DOCSLIB.ORG

Experiment No. 9 DESIGN and CHARACTERISTICS of COMMON

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Experiment No. 9 DESIGN and CHARACTERISTICS of COMMON Experiment No. 9 DESIGN AND CHARACTERISTICS OF COMMON BASE AND COMMON COLLECTOR AMPLIFIERS 1. Objective: The objective of this experiment is to explore the basic applications of the bipolar junction transistor (BJT). A common base and a common collector amplifier will be designed and tested. The frequency response will be measured and the DC voltages will be compared to calculated values. In this experiment, transistor type 2N3904 is used. 2. Introduction: Common emitter amplifiers are the most widely used form of BJT in amplifier configurations. It is mostly used to provide reasonably high voltage gain as well as some power gain. However, another two amplifier configurations can also be used to provide some power gain, or to provide simple interface between various circuits with different impedance levels. The common-base amplifier can provide a reasonable level of voltage gain but suffers from low input impedance and a current gain of less than one. However, this circuit is used in high-frequency applications because its terminal characteristics at high frequencies are better than those of a common-emitter configuration using the same transistor. The low input impedance of the common base amplifier will limit its use to specialized RF applications. The common collector configuration, also typically known as emitter follower, is used primarily as an impedance buffer stage to prevent a low impedance load from loading a stage with relatively high output impedance. The emitter follower has a high input impedance and low output impedance, which is almost equal to the emitter resistance. The voltage gain of the emitter follower is less than one, but it has reasonably high current gain. Unlike the common emitter amplifier, the output voltage of the common collector amplifier is in phase with the input voltage. 3. Pre-Lab work: Design the circuit shown in Figures 1 and 2 by calculating the values of R 1, R 2, R 3 and R 4. 2N3904 NPN transistor is to be used. In this design the bias voltage between emitter and collector should be 5V DC. The quiescent collector current is 1mA. The design should provide maximum possible voltage swing at the amplifier output. Figure 1- Circuit diagram of the common base BJT amplifier configuration. Figure 2- Circuit diagram of the common emitter amplifier configuration. 4. Lab work: a. Connect the common base amplifier circuit you designed. Set the values of capacitors C1, C2, and C3 to 1µF each. Make sure the positive polarity of these capacitors are connected to the higher positive voltage in the circuit. Set R L to be 1 k Ω and the supply voltage to 15V DC, as shown in Figure 3. Measure the DC bias voltages on the base, emitter and the collector. Calculate the collector current. Compare the measured voltages with the design intent and calculation. Tabulate the measured versus the calculated bias voltages and current. Figure 3. Common base amplifier circuit under test. b. Measure the frequency response of the amplifier starting from 100 Hz. Change the test frequency to cover the upper cut-off frequency of the amplifier. Through out the measurement of the frequency response, apply low input signal levels (in the order of few milli-Volts) to ensure that the out put signal is not distorted. Monitor both input and output waveforms on the oscilloscope. Insert R5 = 200 Ω between the source and the common base amplifier input to prevent excessive loading of the signal source by the fairly low input resistance of the amplifier. b.1 Plot the obtained frequency response. On the measured plot clearly indicate the lower and upper cut-off frequencies of the amplifier. b.2 What is the mid-band gain of the amplifier? c.3 Calculate the amplifier bandwidth. c. If you know that the output (internal) resistance of the signal source is 50 Ω at 1kHz frequency, can you make some measurement to determine the input resistance of the common base amplifier at 1kHz frequency? Discuss your idea with the lab supervisor before doing the measurement. Figure 4 - Emitter follower circuit under test. d. Connect the common collector amplifier circuit you designed. Set the values of capacitors C1, C2, and C3 to 1µF each. Set R L to be 1 k Ω and the supply voltage to 15V DC, as shown in Figure 4. Measure the DC bias voltages on the base, emitter and the collector. Calculate the collector current. Compare the measured voltages with the design intent and calculation. Tabulate the measured versus the calculated bias voltages and current. e. Measure the frequency response of the amplifier starting from 100 Hz. change the test frequency to cover the upper cut-off frequency of the amplifier. Through out the measurement of the frequency response, apply low input signal levels (in the order of few milli-Volts) to ensure that the out put signal is not distorted. Monitor both input and output waveforms on the oscilloscope. d.1 Plot the obtained frequency response. On the measured plot clearly indicate the lower and upper cut-off frequencies of the amplifier. d.2 What is the mid-band gain of the amplifier? d.3 Calculate the amplifier bandwidth. 5. Report: In addition to reporting the data obtained in this experiment; a. Comment on the differences between the intended bias voltages for the two amplifiers and the measured voltages. Why there is a difference? How can you reduce this difference when you calculate the bias resistors? b. Compare the voltage gain and bandwidths for the three amplifier configurations, namely, the common emitter, common collector and common base. Tabulate the numbers obtained through out this experiment and the previous experiment to quantify the comparison. .
Load more

Recommended publications
  • PH-218 Lec-12: Frequency Response of BJT Amplifiers
    Analog & Digital Electronics Course No: PH-218 Lec-12: Frequency Response of BJT Amplifiers Course Instructors: Dr. A. P. VAJPEYI Department of Physics, Indian Institute of Technology Guwahati, India 1 High frequency Response of CE Amplifier At high frequencies, internal transistor junction capacitances do come into play, reducing an amplifier's gain and introducing phase shift as the signal frequency increases. In BJT, C be is the B-E junction capacitance, and C bc is the B-C junction capacitance. (output to input capacitance) At lower frequencies, the internal capacitances have a very high reactance because of their low capacitance value (usually only a few pf) and the low frequency value. Therefore, they look like opens and have no effect on the transistor's performance. As the frequency goes up, the internal capacitive reactance's go down, and at some point they begin to have a significant effect on the transistor's gain. High frequency Response of CE Amplifier When the reactance of C be becomes small enough, a significant amount of the signal voltage is lost due to a voltage-divider effect of the source resistance and the reactance of C be . When the reactance of Cbc becomes small enough, a significant amount of output signal voltage is fed back out of phase with the input (negative feedback), thus effectively reducing the voltage gain. 3 Millers Theorem The Miller effect occurs only in inverting amplifiers –it is the inverting gain that magnifies the feedback capacitance. vin − (−Av in ) iin = = vin 1( + A)× 2π × f ×CF X C Here C F represents C bc vin 1 1 Zin = = = iin 1( + A)× 2π × f ×CF 2π × f ×Cin 1( ) Cin = + A ×CF 4 High frequency Response of CE Amp.: Millers Theorem Miller's theorem is used to simplify the analysis of inverting amplifiers at high-frequencies where the internal transistor capacitances are important.
    [Show full text]
  • Common Drain - Wikipedia, the Free Encyclopedia 10-5-17 下午7:07
    Common drain - Wikipedia, the free encyclopedia 10-5-17 下午7:07 Common drain From Wikipedia, the free encyclopedia In electronics, a common-drain amplifier, also known as a source follower, is one of three basic single- stage field effect transistor (FET) amplifier topologies, typically used as a voltage buffer. In this circuit the gate terminal of the transistor serves as the input, the source is the output, and the drain is common to both (input and output), hence its name. The analogous bipolar junction transistor circuit is the common- collector amplifier. In addition, this circuit is used to transform impedances. For example, the Thévenin resistance of a combination of a voltage follower driven by a voltage source with high Thévenin resistance is reduced to only the output resistance of the voltage follower, a small resistance. That resistance reduction makes the combination a more ideal voltage source. Conversely, a voltage follower inserted between a small load resistance and a driving stage presents an infinite load to the driving stage, an advantage in coupling a voltage signal to a small load. Characteristics At low frequencies, the source follower pictured at right has the following small signal characteristics.[1] Voltage gain: Current gain: Input impedance: Basic N-channel JFET source Output impedance: (the parallel notation indicates the impedance follower circuit (neglecting of components A and B that are connected in parallel) biasing details). The variable gm that is not listed in Figure 1 is the transconductance of the device (usually given in units of siemens). References http://en.wikipedia.org/wiki/Common_drain Page 1 of 2 Common drain - Wikipedia, the free encyclopedia 10-5-17 下午7:07 1.
    [Show full text]
  • Cascode Amplifiers by Dennis L. Feucht Two-Transistor Combinations
    Cascode Amplifiers by Dennis L. Feucht Two-transistor combinations, such as the Darlington configuration, provide advantages over single-transistor amplifier stages. Another two-transistor combination in the analog designer's circuit library combines a common-emitter (CE) input configuration with a common-base (CB) output. This article presents the design equations for the basic cascode amplifier and then offers other useful variations. (FETs instead of BJTs can also be used to form cascode amplifiers.) Together, the two transistors overcome some of the performance limitations of either the CE or CB configurations. Basic Cascode Stage The basic cascode amplifier consists of an input common-emitter (CE) configuration driving an output common-base (CB), as shown above. The voltage gain is, by the transresistance method, the ratio of the resistance across which the output voltage is developed by the common input-output loop current over the resistance across which the input voltage generates that current, modified by the α current losses in the transistors: v R A = out = −α ⋅α ⋅ L v 1 2 β + + + vin RB /( 1 1) re1 RE where re1 is Q1 dynamic emitter resistance. This gain is identical for a CE amplifier except for the additional α2 loss of Q2. The advantage of the cascode is that when the output resistance, ro, of Q2 is included, the CB incremental output resistance is higher than for the CE. For a bipolar junction transistor (BJT), this may be insignificant at low frequencies. The CB isolates the collector-base capacitance, Cbc (or Cµ of the hybrid-π BJT model), from the input by returning it to a dynamic ground at VB.
    [Show full text]
  • I. Common Base / Common Gate Amplifiers
    I. Common Base / Common Gate Amplifiers - Current Buffer A. Introduction • A current buffer takes the input current which may have a relatively small Norton resistance and replicates it at the output port, which has a high output resistance • Input signal is applied to the emitter, output is taken from the collector • Current gain is about unity • Input resistance is low • Output resistance is high. V+ V+ i SUP ISUP iOUT IOUT RL R is S IBIAS IBIAS V− V− (a) (b) B. Biasing = /α ≈ • IBIAS ISUP ISUP EECS 6.012 Spring 1998 Lecture 19 II. Small Signal Two Port Parameters A. Common Base Current Gain Ai • Small-signal circuit; apply test current and measure the short circuit output current ib iout + = β v r gmv oib r − o ve roc it • Analysis -- see Chapter 8, pp. 507-509. • Result: –β ---------------o ≅ Ai = β – 1 1 + o • Intuition: iout = ic = (- ie- ib ) = -it - ib and ib is small EECS 6.012 Spring 1998 Lecture 19 B. Common Base Input Resistance Ri • Apply test current, with load resistor RL present at the output + v r gmv r − o roc RL + vt i − t • See pages 509-510 and note that the transconductance generator dominates which yields 1 Ri = ------ gm µ • A typical transconductance is around 4 mS, with IC = 100 A • Typical input resistance is 250 Ω -- very small, as desired for a current amplifier • Ri can be designed arbitrarily small, at the price of current (power dissipation) EECS 6.012 Spring 1998 Lecture 19 C. Common-Base Output Resistance Ro • Apply test current with source resistance of input current source in place • Note roc as is in parallel with rest of circuit g v m ro + vt it r − oc − v r RS + • Analysis is on pp.
    [Show full text]
  • Dynamic Microphone Amplifier
    Dynamic Microphone Preamp Description: A low noise pre-amplifier suitable for amplifying dynamic microphones with 200 to 600 ohm output impedance. Notes: This is a 3 stage discrete amplifier with gain control. Alternative transistors such as BC109C, BC548, BC549, BC549C may be used with little change in performance. The first stage built around Q1 operates in common base configuration. This is unusuable in audio stages, but in this case, it allows Q1 to operate at low noise levels and improves overall signal to noise ratio. Q2 and Q3 form a direct coupled amplifier, similar to my earlier mic preamp . Input and Output Impedance: As the signal from a dynamic microphone is low typically much less than 10mV, then there is little to be gained by setting the collector voltage voltage of Q1 to half the supply voltage. In power amplifiers, biasing to half the supply voltage allows for maximum voltage swing, and highest overload margin, but where input levels are low, any value in the linear part of the operating characteristics will suffice. Here Q1 operates with a collector voltage of 2.4V and a low collector current of around 200uA. This low collector current ensures low noise performance and also raises the input impedance of the stage to around 400 ohms. This is a good match for any dynamic microphone having an impedances between 200 and 600 ohms. The output impedance at Q3 is low, the graph of input and output impedance versus frequency is shown below: Gain and Frequency Response: The overall gain of this pre-amplifier is around +39dB or about 90 times.
    [Show full text]
  • Lecture23-Amplifier Frequency Response.Pptx
    EE105 – Fall 2014 Microelectronic Devices and Circuits Prof. Ming C. Wu [email protected] 511 Sutardja Dai Hall (SDH) Lecture23-Amplifier Frequency Response 1 Common-Emitter Amplifier – ωH Open-Circuit Time Constant (OCTC) Method At high frequencies, impedances of coupling and bypass capacitors are small enough to be considered short circuits. Open-circuit time constants associated with impedances of device capacitances are considered instead. 1 ωH ≅ m ∑RioCi i=1 where Rio is resistance at terminals of ith capacitor C with all other v ! R $ i R = x = r #1+ g R + L & capacitors open-circuited. µ 0 π 0 m L ix " rπ 0 % For a C-E amplifier, assuming C = 0 L 1 1 ωH ≅ = Rπ 0 = rπ 0 Rπ 0Cπ + Rµ 0Cµ rπ 0CT Lecture23-Amplifier Frequency Response 2 1 Common-Emitter Amplifier High Frequency Response - Miller Effect • First, find the simplified small -signal model of the C-E amp. • Replace coupling and bypass capacitors with short circuits • Insert the high frequency small -signal model for the transistor ! # rπ 0 = rπ "rx +(RB RI )$ Lecture23-Amplifier Frequency Response 3 Common-Emitter Amplifier – ωH High Frequency Response - Miller Effect (cont.) v R r Input gain is found as A = b = in ⋅ π i v R R r r i I + in x + π R || R || (r + r ) r = 1 2 x π ⋅ π RI + R1 || R2 || (rx + rπ ) rx + rπ Terminal gain is vc Abc = = −gm (ro || RC || R3 ) ≅ −gm RL vb Using the Miller effect, we find CeqB = Cµ (1− Abc )+Cπ (1− Abe ) the equivalent capacitance at the base as: = Cµ (1−[−gm RL ])+Cπ (1− 0) = Cµ (1+ gm RL )+Cπ Chap 17-4 Lecture23-Amplifier Frequency Response 4 2 Common-Emitter Amplifier – ωH High Frequency Response - Miller Effect (cont.) ! # • The total equivalent resistance ReqB = rπ 0 = rπ "rx +(RB RI )$ at the base is • The total capacitance and CeqC = Cµ +CL resistance at the collector are ReqC = ro RC R3 = RL • Because of interaction through 1 ω = Cµ, the two RC time constants p1 ! # rπ 0 "Cπ +Cµ (1+ gm RL )$+ RL (Cµ +CL ) interact, giving rise to a dominant pole.
    [Show full text]
  • Notes on BJT & FET Transistors
    Phys2303 L.A. Bumm [ver 1.1] Transistors (p1) Notes on BJT & FET Transistors. Comments. The name transistor comes from the phrase “transferring an electrical signal across a resistor.” In this course we will discuss two types of transistors: The Bipolar Junction Transistor (BJT) is an active device. In simple terms, it is a current controlled valve. The base current (IB) controls the collector current (IC). The Field Effect Transistor (FET) is an active device. In simple terms, it is a voltage controlled valve. The gate-source voltage (VGS) controls the drain current (ID). Regions of BJT operation: Cut-off region: The transistor is off. There is no conduction between the collector and the emitter. (IB = 0 therefore IC = 0) Active region: The transistor is on. The collector current is proportional to and controlled by the base current (IC = βIC) and relatively insensitive to VCE. In this region the transistor can be an amplifier. Saturation region: The transistor is on. The collector current varies very little with a change in the base current in the saturation region. The VCE is small, a few tenths of volt. The collector current is strongly dependent on VCE unlike in the active region. It is desirable to operate transistor switches will be in or near the saturation region when in their on state. Rules for Bipolar Junction Transistors (BJTs): • For an npn transistor, the voltage at the collector VC must be greater than the voltage at the emitter VE by at least a few tenths of a volt; otherwise, current will not flow through the collector-emitter junction, no matter what the applied voltage at the base.
    [Show full text]
  • Lecture 19 Common-Gate Stage
    4/7/2008 Lecture 19 OUTLINE • Common‐gate stage • Source follower • Reading: Chap. 7.3‐7.4 EE105 Spring 2008 Lecture 19, Slide 1Prof. Wu, UC Berkeley Common‐Gate Stage AvmD= gR • Common‐gate stage is similar to common‐base stage: a rise in input causes a rise in output. So the gain is positive. EE105 Spring 2008 Lecture 19, Slide 2Prof. Wu, UC Berkeley EE105 Fall 2007 1 4/7/2008 Signal Levels in CG Stage • In order to maintain M1 in saturation, the signal swing at Vout cannot fall below Vb‐VTH EE105 Spring 2008 Lecture 19, Slide 3Prof. Wu, UC Berkeley I/O Impedances of CG Stage 1 R = in λ =0 RRout= D gm • The input and output impedances of CG stage are similar to those of CB stage. EE105 Spring 2008 Lecture 19, Slide 4Prof. Wu, UC Berkeley EE105 Fall 2007 2 4/7/2008 CG Stage with Source Resistance 1 g vv= m Xin1 + RS gm 1 vv g AgR==out x m vmD1 vvxin + RS gm R gR ==D mD 1 1+ gRmS + RS gm • When a source resistance is present, the voltage gain is equal to that of a CS stage with degeneration, only positive. EE105 Spring 2008 Lecture 19, Slide 5Prof. Wu, UC Berkeley Generalized CG Behavior Rgout= (1++g mrR O) S r O • When a gate resistance is present it does not affect the gain and I/O impedances since there is no potential drop across it (at low frequencies). • The output impedance of a CG stage with source resistance is identical to that of CS stage with degeneration.
    [Show full text]
  • FJP2145 — ESBC™ Rated NPN Power Transistor MOS- (2) ™ March 2015 FDC655 FJP2145 S C G B Figure 3
    FJP2145 — ESBC™ Rated ESBC™ FJP2145 — March 2015 FJP2145 ESBC™ Rated NPN Power Transistor ESBC Features (FDC655 MOSFET) Description NPN Power Transistor (1) The FJP2145 is a low-cost, high-performance power VCS(ON) IC Equiv. RCS(ON) switch designed to provide the best performance when 0.21 V 2 A 0.105 Ω used in an ESBC™ configuration in applications such as: • Low Equivalent On Resistance power supplies, motor drivers, smart grid, or ignition • Very Fast Switch: 150 kHz switches. The power switch is designed to operate up to 1100 volts and up to 5 amps, while providing exception- • Wide RBSOA: Up to 1100 V ally low on-resistance and very low switching losses. •Avalanche Rated ™ • Low Driving Capacitance, No Miller Capacitance The ESBC switch can be driven using off-the-shelf power supply controllers or drivers. The ESBC™ MOS- • Low Switching Losses FET is a low-voltage, low-cost, surface-mount device that • Reliable HV Switch: No False Triggering due to combines low-input capacitance and fast switching. The High dv/dt Transients ESBC™ configuration further minimizes the required driv- ing power because it does not have Miller capacitance. Applications The FJP2145 provides exceptional reliability and a large • High-Voltage, High-Speed Power Switch operating range due to its square reverse-bias-safe-oper- • Emitter-Switched Bipolar/MOSFET Cascode ating-area (RBSOA) and rugged design. The device is (ESBC™) avalanche rated and has no parasitic transistors, so is not prone to static dv/dt failures. • Smart Meters, Smart Breakers, SMPS, HV Industrial Power Supplies The power switch is manufactured using a dedicated • Motor Drivers and Ignition Drivers high-voltage bipolar process and is packaged in a high- voltage TO-220 package.
    [Show full text]
  • High-Frequency Amplifier Response
    Section H5: High-Frequency Amplifier Response Now that we’ve got a high frequency models for the BJT, we can analyze the high frequency response of our basic amplifier configurations. Note: in the circuits that follow, the actual signal source (vS) and its associated source resistance (RS) have been included. As discussed in the low frequency response section of our studies, we always knew that this source and resistance was there but we just started our investigations with the input to the transistor (vin). Remember - the analysis process is the same and the relationship between vS and vin is a voltage divider! Again, in some instances in the following discussion, I will be using slightly different notation and taking a different approach than your author. As usual, if this results in confusion, or you are more comfortable with his technique, let me know and we’ll work it out. High Frequency Response of the CE and ER Amplifier The generic common-emitter amplifier circuit of Section D2 is reproduced to the left below and the small signal circuit using the high frequency BJT model is given below right (based on Figures 10.17a and 10.17b of your text). Note that all external capacitors are assumed to be short circuits at high frequencies and are not present in the high frequency equivalent circuit (since the external capacitors are large when compared to the internal capacitances – recall that Zc=1/jωC gets small as the frequency or capacitance gets large). We can simplify the small signal circuit by making the following observations and approximations: ¾ Cce is very small and may be neglected.
    [Show full text]
  • Designing a Common-Collector Amplifier
    SCHOOL OF ENGINEERING AND APPLIED SCIENCE DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING ECE 2115: ENGINEERING ELECTRONICS LABORATORY Tutorial #6: Designing a Common-Collector Amplifier BACKGROUND In the previous lab, you designed a common-emitter (CE) amplifier. Voltage gain (AV) is easy to achieve with this type of amplifier. As you discovered, the input impedance (Rin) of the CE amplifier is moderate- to-high (on the order of a few kΩ). The output impedance (Rout) is high (roughly the value of RC). This makes the common-emitter amplifier a poor choice for “driving” small loads. A common-collector (CC) amplifier typically has a high input impedance (typically in the hundred kΩ range) and a very low output impedance (on the order of 1Ω or 10Ω). This makes the common- collector amplifier excellent for “driving” small loads. As you discovered in Lab 6, the common-collector amplifier has a voltage gain of about 1, or unity gain. The common-collector amplifier is considered a voltage-buffer since the voltage gain is unity. The voltage signal applied at the input will be duplicated at the output; for this reason, the common-collector amplifier is typically called an emitter-follow amplifier. The common-collector amplifier can be thought of as a current amplifier. When the common-emitter amplifier is cascaded to a common-collector amplifier, the CC amplifier can be thought of as an “impedance transformer.” It can take the high output impedance of the CE amplifier and “transform” it to a low output impedance capable of driving small loads. Figure 1 shows a typical configuration for a common-collector amplifier.
    [Show full text]
  • BJT Small-Signal Model
    EE105 – Fall 2014 Microelectronic Devices and Circuits Prof. Ming C. Wu [email protected] 511 Sutardja Dai Hall (SDH) Lecture12-Small Signal Model-BJT 1 Introduction to Amplifiers • Amplifiers: transistors biased in the flat-part of the i-v curves – BJT: forward-active region – MOSFET: saturation region • In these regions, transistors can provide high voltage, current and power gains • Bias is provided to stabilize the operating point (the Q-Point) in the desired region of operation • Q-point also determines – Small-signal parameters of transistor – Voltage gain, input resistance, output resistance – Maximum input and output signal amplitudes – Power consumption Lecture12-Small Signal Model-BJT 2 1 Transistor Amplifiers BJT Amplifier Concept The BJT is biased in the active region by dc voltage source VBE. e.g., Q-point is set at (IC, VCE) = (1.5 mA, 5 V) with IB = 15 µA (βF = 100) Total base-emitter voltage is: vBE = VBE + vbe Collector-emitter voltage is: vCE = VCC – iCRC This is the load line equation. Lecture12-Small Signal Model-BJT 3 Transistor Amplifiers BJT Amplifier (cont.) If changes in operating currents and voltages are small enough, then iC and vCE waveforms are undistorted replicas of the input signal. A small voltage change at the base causes a large voltage change at collector. Voltage gain is given by: o Vce 1.65∠180 o Av = = o = 206∠180 = −206 8 mV peak change in vBE gives 5 mA Vbe 0.008∠0 change in iB and 0.5 mA change in iC. Minus sign indicates 180o phase 0.5 mA change in iC produces a 1.65 shift between the input and output V change in vCE .
    [Show full text]