DOCSLIB.ORG

Advanced Germanium Complementary-Metal-Oxide-Semiconductor Technologies

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Advanced Germanium Complementary-Metal-Oxide-Semiconductor Technologies ADVANCED GERMANIUM COMPLEMENTARY-METAL-OXIDE-SEMICONDUCTOR TECHNOLOGIES A DISSERTATION SUBMITTED TO THE DEPARTMENT OF ELECTRICAL ENGINEERING AND THE COMMITTEE ON GRADUATE STUDIES OF STANFORD UNIVERSITY IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF DOCTOR OF PHILOSOPHY Chi On Chui August 2004 © Copyright by Chi On Chui 2004 All Rights Reserved ii I certify that I have read this dissertation and that, in my opinion, it is fully adequate in scope and quality as a dissertation for the degree of Doctor of Philosophy. __________________________________________ Krishna C. Saraswat (Principal Advisor) I certify that I have read this dissertation and that, in my opinion, it is fully adequate in scope and quality as a dissertation for the degree of Doctor of Philosophy. __________________________________________ Yoshio Nishi I certify that I have read this dissertation and that, in my opinion, it is fully adequate in scope and quality as a dissertation for the degree of Doctor of Philosophy. __________________________________________ Paul C. McIntyre Approved for the University Committee on Graduate Studies __________________________________________ iii This thesis is dedicated to my family iv Abstract Drive current saturation in scaled Si MOSFETs is fundamentally limiting the prospect of future scaling. To overcome this scaling bottleneck and allow further improvements on short-channel MOSFET drive current, Ge MOSFET channel with high carrier mobility and source injection velocity should be incorporated. However, the unstable Ge native oxide for gate insulation and field isolation, together with the high diffusivity and low solubility of n-type Ge dopants for source and drain junction formation are the two classical problems that have obstructed CMOS device realization in Ge for four decades. In this work, three types of nanoscale gate dielectric for Ge MOS applications are investigated. The scalability and stability of native Ge oxynitrides are first examined followed by a seminal investigation and demonstration of integration of the more scalable and stable high-k metal oxides for Ge MOS applications. The effects of different Ge surface cleaning and passivation strategies are discussed, leading to the demonstration of sub-1.0 nm equivalent SiO 2 thickness dielectric stack on Ge. Additionally, two techniques to form shallow junctions for Ge MOSFET source and drain applications are studied. The corresponding activation and diffusion of various p-type and n-type dopants in Ge are analyzed after either the ion implantation or solid source diffusion doping. Through monitoring the thermal stability of the out-diffused dopants, phosphorus deactivation in Ge is observed for the first time. Finally, two low thermal budget processes to fabricate Ge MOSFETs are developed using the above dielectric and junction technologies. Metal gate high-k Ge p- MOSFETs are fabricated without exceeding 400 °C that demonstrate effective hole mobility enhancement over the silicon universal mobility model. On the other hand, functional metal gate high-k Ge n-MOSFETs are built using an innovative self-aligned gate-last process, which could be used as a technology vehicle to expedite the evaluation of numerous novel materials integration for advanced MOSFET applications. v Acknowledgements The accomplishment of this Ph.D. would never be possible without the supports from many individuals. First and foremost, I would like to express my sincere gratitude to my principal advisor, Professor Krishna C. Saraswat, for all his guidance and support in my last 4 years in the group. I am particularly impressed by his deep insights on many apparently general problems as well as his vision on numerous future potential research areas of interest. His liberal style in supervising students and his unselfishness in sharing credit are the most valuable characteristics for me to learn from. In addition, I would like to thank the members of my reading and orals committee including Professor Yoshio Nishi for his useful advice and continuous encouragement, Professor Paul C. McIntyre for making possible my collaboration with his group on high-k dielectric issues, and Professor Piero A. Pianetta for enabling my interaction with his team on synchrotron radiation photoemission studies. The invaluable consultation from a number of experts is another key to success. Above all, I would like to pay my tribute to Dr. James P. McVittie, whose significant contributions are usually ignored as an un-named hero, for his hands-on experimental assistance. Secondly, I would like to acknowledge Dr. Baylor B. Triplett for his initial help on the high-k dielectric on Ge feasibility study and spreading his expertise on SiO 2 on Si interfaces. Thirdly, I am extremely grateful to Prof. Eugene E. Haller (from UC Berkeley) for our numerous phone discussions to check out his career-long experience on Ge. Also, other specialists’ advices from Dr. Michael Deal, Prof. Robert Dutton, Dr. Peter Griffin, Dr. Christoph Jungemann, Dr. Ann Marshall, Prof. James Meindl (from Georgia Tech) and Prof. James Plummer are undoubtedly gratefully acknowledged. Additionally, I would like to greet the prompt and fruitful collaborations with Stanford insiders like David Chi, Kailash Gopalakrishnan, Fumitoshi Ito, Hyoungsub Kim, Hai Lan, Dong-Ick Lee, Yang Liu, Eric Pop, Shriram Ramanathan, Andy Singh, and Shiyu Sun, as well as outsiders like Muhannad Bakir from Georgia Tech and Jungwoo Oh from UT Austin. vi Due to the inherent experimental nature of this work, the helps from many SNF lab members should not be forgotten. Dr. Eric Perozziello, Pat Castle and Hector Cavazos have been my life-savers for years. Moreover, my processing time would not have been such enjoyable and productive without the presence of Cesar Baxter, Len Booth, Dick Crane, Elmer Enriquez, Carl Faulkner, Dan Grupp, Jim Haydon, Sameer Jain, Paul Jerabek, Eun-ha Kim, Robin King, Nancy Latta, Frankie Liu, Yaocheng Liu, Mahnaz Mansourpour, Mike Martinez, Chang-man Park, Henry Phan, Gladys Sarmiento, John Shott, Maurice Stevens, Yayoi Takamura, Mario Vilanova, Dunwei Wang, and many others. Also, I would thank Tom Carver of the Ginzton Lab for running literally hundreds of metal evaporations for me. Throughout these years residing in CIS, I have gotten many times help from staff including Dr. Richard Dasher, Maureen Rochford, and Carmen Mriaflor. Besides, I am very grateful to numerous members of Prof. Saraswat’s group, past and present, who have provided me with help and advice including Amol Joshi, Rohit Shenoy, Albert Wang, Dan Connelly, Ting-Yen Chiang, Marci Liao, Ali Okyay, Ammar Nayfeh, and Abhijit Pethe. Thanks especially to Irene Sweeney for her prompt and untiring administrative assistance on my behalf. Last but not least, thanks go to my wonderful family for sharing their endless love and support with me. Thanks go to my parents and brother for their care and for being there whenever I need them. Thanks to my wife, Hoi Yan, for her creativity and skill in preparing delicious dishes, her love and smile, and always being a good listener to me. I pray for their happiness and good health, and I dedicate my work to them in the most sincere way I can think of. vii Table of Contents Abstract......................................................................................................... v Acknowledgments....................................................................................... vi Table of Contents...................................................................................... viii List of Tables............................................................................................... xi List of Figures............................................................................................. xii Chapter 1. Introduction............................................................................... 1 1.1 Drive Current Saturation in Scaled Si MOSFETs............................................... 1 1.2 Demand for Germanium Channel MOSFETs...................................................... 5 1.2.1 Physical and Historical Facts about Germanium...................................... 5 1.2.2 CMOS Performance Boost with Germanium............................................ 9 1.3 Thesis Objective and Organization.................................................................... 13 Chapter 2. Nanoscale Ge MOS Gate Dielectrics: From native GeOxNy to high-k MOx.............................................................................. 15 2.1 Introduction........................................................................................................ 15 2.2 Native Germanium MOS Dielectrics................................................................. 18 2.2.1 Germanium Oxidations........................................................................... 18 2.2.2 The Rapid Thermal Processing System................................................... 20 2.2.3 Germanium Oxynitride Synthesis........................................................... 21 2.2.4 Scaling and Electrical Characterizations of Oxynitride.......................... 23 2.2.5 Effects and Degree of Nitridation in Oxynitride..................................... 28 2.2.6 Oxynitride-Germanium Interface Trapped Charge................................. 29 2.3 High-k Dielectrics by Atomic Layer Deposition............................................... 31 2.3.1 High-k Dielectric Motivation and Selection..........................................
Load more

Recommended publications
  • Standard X-Ray Diffraction Powder Patterns
    NBS MONOGRAPH 25 — SECTION 1 Standard X-ray Diffraction U.S. DEPARTMENT OF COMMERCE NATIONAL BUREAU OF STANDARDS THE NATIONAL BUREAU OF STANDARDS Functions and Activities The functions of the National Bureau of Standards are set forth in the Act of Congress, March 3, 1901, as amended by Congress in Public Law 619, 1950. These include the development and maintenance of the national standards of measurement and the provision of means and methods for making measurements consistent with these standards; the determination of physical constants and properties of materials; the development of methods and instruments for testing materials, devices, and structures; advisory services to government agencies on scien- tific and technical problems; invention and development of devices to serve special needs of the Government; and the development of standard practices, codes, and specifications. The work includes basic and applied research, development, engineering, instrumentation, testing, evaluation, calibration services, and various consultation and information services. Research projects are also performed for other government agencies when the work relates to and supplements the basic program of the Bureau or when the Bureau's unique competence is required. The scope of activities is suggested by the listing of divisions and sections on the inside of the back cover. Publications The results of the Bureau's research are published either in the Bureau's own series of publications or in the journals of professional and scientific societies. The Bureau itself publishes three periodicals available from the Government Printing Office: The Journal of Research, published in four separate sections, presents complete scientific and technical papers; the Technical News Bulletin presents summary and preliminary reports on work in progress; and Basic Radio Propagation Predictions provides data for determining the best frequencies to use for radio communications throughout the world.
    [Show full text]
  • Physical and Chemical Properties of Germanium
    Physical And Chemical Properties Of Germanium Moneyed and amnesic Erasmus fertilise her fatuousness revitalise or burrow incommunicatively. Creditable Petr still climbs: regarding and lissome Lazarus bully-off quite punctiliously but slums her filoplume devotedly. Zane still defilade venomous while improvident Randell bloodiest that wonderers. Do you for this context of properties and physical explanation of Silicon is sincere to metals in its chemical behaviour. Arsenic is extremely toxic, RS, carbon is the tongue one considered a full nonmetal. In nature, which name a widely used azo dye. Basic physical and chemical properties of semiconductors are offset by the energy gap between valence conduction! Other metalloids on the periodic table are boron, Batis ZB, only Germanium and Antimony would be considered metals for the purposes of nomenclature. Storage temperature: no restrictions. At room temperature, the semiconducting elements are primarily nonmetallic in character. This application requires Javascript. It has also new found in stars and already the atmosphere of Jupiter. Wellings JS, it is used as an eyewash and insecticide. He has studied in Spain and Hungary and authored many research articles published in indexed journals and books. What are oral health benefits of pumpkins? The material on this site may not be reproduced, germanium, the radiation emitted from an active device makes it locatable. Classify each statement as an extensive property must an intensive property. In germanium and physical chemical properties of the border lines from the! The most electronegative elements are at the nod in the periodic table; these elements often react as oxidizing agents. Atomic Volume and Allotropy of the Elements.
    [Show full text]
  • P020190719572604117959.Pdf
    Springer Series in advanced microelectronics 27 Springer Series in advanced microelectronics Series Editors: K. Itoh T. Lee T. Sakurai W.M.C. Sansen D. Schmitt-Landsiedel The Springer Series in Advanced Microelectronics provides systematic information on all the topics relevant for the design, processing, and manufacturing of microelectronic devices. The books, each prepared by leading researchers or engineers in their fields, cover the basic and advanced aspects of topics such as wafer processing, materials, device design, device technologies, circuit design, VLSI implementation, and subsys- tem technology. The series forms a bridge between physics and engineering and the volumes will appeal to practicing engineers as well as research scientists. 18 Microcontrollers in Practice By I. Susnea and M. Mitescu 19 Gettering Defects in Semiconductors By V.A. Perevoschikov and V.D. Skoupov 20 Low Power VCO Design in CMOS By M. Tiebout 21 Continuous-Time Sigma-Delta A/D Conversion Fundamentals, Performance Limits and Robust Implementations By M. Ortmanns and F. Gerfers 22 Detection and Signal Processing Technical Realization By W.J. Witteman 23 Highly Sensitive Optical Receivers By K. Schneider and H.K. Zimmermann 24 Bonding in Microsystem Technology By J.A. Dziuban 25 Power Management of Digital Circuits in Deep Sub-Micron CMOS Technologies By S. Henzler 26 High-Dynamic-Range (HDR) Vision Microelectronics, Image Processing, Computer Graphics Editor: B. Hoefflinger 27 Advanced Gate Stacks for High-Mobility Semiconductors Editors: A. Dimoulas, E. Gusev, P.C. McIntyre, and M. Heyns Volumes 1–17 are listed at the end of the book. A. Dimoulas E. Gusev P.C. McIntyre M.
    [Show full text]
  • The Separation of Germanium from Lead, Cadmium, and Zinc by Ion Exchange
    Scholars' Mine Masters Theses Student Theses and Dissertations 1962 The separation of germanium from lead, cadmium, and zinc by ion exchange Myra Sue Anderson Follow this and additional works at: https://scholarsmine.mst.edu/masters_theses Part of the Chemistry Commons Department: Recommended Citation Anderson, Myra Sue, "The separation of germanium from lead, cadmium, and zinc by ion exchange" (1962). Masters Theses. 2730. https://scholarsmine.mst.edu/masters_theses/2730 This thesis is brought to you by Scholars' Mine, a service of the Missouri S&T Library and Learning Resources. This work is protected by U. S. Copyright Law. Unauthorized use including reproduction for redistribution requires the permission of the copyright holder. For more information, please contact [email protected]. THE SEPARATION OF GERMANIUM FROM LEAD, CADMIUM, AND ZINC BY ION EXCHANGE BY MYRA SUE ANDERSON A THESIS submitted to the faculty of the SCHOOL OF MINES AND METALLURGY OF THE UNIVERSITY OF MISSOURI In partial fulfillment of the requirements for the Degree of MASTER OF SCIENCE IN CHEMISTRY Rolla, Missouri 1962 Approved by (advisor) //f 11 TABLE OF CONTENTS Page List of Illustrations Iv List of Tables V Introduction 1 Review of the Literature 2 Separation Methods for Germanium 2 Analytical Methods for Germanium 3 Germanium Complexes Suitable for Ion Exchange 6 Ion Exchange Resins 7 Ion Exchange Theory 9 Ion Exchange Studies of Germanium 15 Experimental 17 Materials 17 Apparatus 18 Analytical Methods 19 Anion Exchange Studies 21 Cation Exchange Studies
    [Show full text]
  • Reactive Sputtering of Complex Multi-Component Nitride Thin Films
    Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology 1852 Reactive Sputtering of Complex Multi-component Nitride Thin Films KRISTINA VON FIEANDT ACTA UNIVERSITATIS UPSALIENSIS ISSN 1651-6214 ISBN 978-91-513-0744-2 UPPSALA urn:nbn:se:uu:diva-392704 2019 Dissertation presented at Uppsala University to be publicly examined in Polhemssalen, Ångströmslaboratoriet, Lägerhyddsvägen 1, Uppsala, Friday, 25 October 2019 at 09:15 for the degree of Doctor of Philosophy. The examination will be conducted in English. Faculty examiner: Professor Jean-Francois Pierson (University of Lorraine). Abstract von Fieandt, K. 2019. Reactive Sputtering of Complex Multi-component Nitride Thin Films. Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology 1852. 71 pp. Uppsala: Acta Universitatis Upsaliensis. ISBN 978-91-513-0744-2. The ever-increasing demand on improvement of protective nitride thin films has led to an expansion of the research field into multi-element based materials. The work in this thesis has focused on exploring new complex, multi-component nitride thin films based on three different material systems: Al-Ge-N, Hf-Nb-Ti-V-Zr-N and Al-Cr-Nb-Y-Zr-N. All films were synthesised by reactive dc magnetron sputtering and characterised with regard to structure and material properties, in particular the mechanical, optical and corrosion properties. The Al-Ge-O-N coatings exhibited amorphisation of the structure upon oxygen addition, via the formation of a crystalline (Al1-xGex)(N1-yOy) solid solution phase for low O contents. The mechanical properties were improved, and hardness values up to 29 GPa were achieved for low O and Ge concentrations, most likely due to nanocomposite hardening.
    [Show full text]
  • High Purity Inorganics
    High Purity Inorganics www.alfa.com INCLUDING: • Puratronic® High Purity Inorganics • Ultra Dry Anhydrous Materials • REacton® Rare Earth Products www.alfa.com Where Science Meets Service High Purity Inorganics from Alfa Aesar Known worldwide as a leading manufacturer of high purity inorganic compounds, Alfa Aesar produces thousands of distinct materials to exacting standards for research, development and production applications. Custom production and packaging services are part of our regular offering. Our brands are recognized for purity and quality and are backed up by technical and sales teams dedicated to providing the best service. This catalog contains only a selection of our wide range of high purity inorganic materials. Many more products from our full range of over 46,000 items are available in our main catalog or online at www.alfa.com. APPLICATION FOR INORGANICS High Purity Products for Crystal Growth Typically, materials are manufactured to 99.995+% purity levels (metals basis). All materials are manufactured to have suitably low chloride, nitrate, sulfate and water content. Products include: • Lutetium(III) oxide • Niobium(V) oxide • Potassium carbonate • Sodium fluoride • Thulium(III) oxide • Tungsten(VI) oxide About Us GLOBAL INVENTORY The majority of our high purity inorganic compounds and related products are available in research and development quantities from stock. We also supply most products from stock in semi-bulk or bulk quantities. Many are in regular production and are available in bulk for next day shipment. Our experience in manufacturing, sourcing and handling a wide range of products enables us to respond quickly and efficiently to your needs. CUSTOM SYNTHESIS We offer flexible custom manufacturing services with the assurance of quality and confidentiality.
    [Show full text]
  • Treat the Metal Nanoparticles to a Surface Modifier to Form Surface Modified Metal Nanoparticles
    US007259101B2 (12) United States Patent (10) Patent No.: US 7.259,101 B2 Zurcher et al. (45) Date of Patent: Aug. 21, 2007 (54) NANOPARTICLES AND METHOD FOR 4,381.945. A 5/1983 Nair .......................... 106.1.14 MAKING THE SAME 4.418,099 A 1 1/1983 Cuevas et al. .............. 427,229 4,463,030 A 7, 1984 Deffeyes et al. ............ 427,216 (75) Inventors: Fabio Zurcher, Brisbane, CA (US); Brent Ridley, San Carlos, CA (US); (Continued) Klaus Kunze, Half Moon Bay, CA FOREIGN PATENT DOCUMENTS (US); Scott Haubrich, Castro Valley, CA (US); Joerg Rockenberger, EP 1 OOO 949 A1 5, 2000 Redwood City,ty CA (US)(US (Continued) (73) Assignee: Kovio, Inc., Sunnyvale, CA (US) OTHER PUBLICATIONS (*) Notice: Subject to any disclaimer, the term of this “Enhanced Photoluminescence from Si Nano-organosols by patent is extended or adjusted under 35 Functionalization with Alkenes and Their Size Evolution', Shu U.S.C. 154(b) by 96 days. Man Liu et al., 2006, American Chemical Society, p. 637-642. (21) Appl. No.: 11/271,042 (Continued) Primaryy Examiner Savitri Mulpurip (22) Filed: Nov. 10, 2005 (74) Attorney, Agent, or Firm—Haverstock & Owens LLP (65) Prior Publication Data (57) ABSTRACT US 2007/O167O19 A1 Jul. 19, 2007 A method for making nanoparticles, nanoparticle inks and Related U.S. Application Data device layers therefrom is disclosed. In accordance with the (62) Division of application No. 10/339,741, filed on Jan present invention, nanoparticles are isolated from a com 8, 2003 re t. No. 7 078 276 s us posite material that is formed by treating a metal oxide s , now Fal.
    [Show full text]
  • Peculiarities of the Thermo-Optic Coefficient at High Temperatures in Fibers Containing Bragg Gratings
    PECULIARITIES OF THE THERMO-OPTIC COEFFICIENT AT HIGH TEMPERATURES IN FIBERS CONTAINING BRAGG GRATINGS A Thesis Presented to The Graduate Faculty of The University of Akron In Partial Fulfillment of the Requirements for the Degree Master of Science Igor Fedin August, 2011 PECULIARITIES OF THE THERMO-OPTIC COEFFICIENT AT HIGH TEMPERATURES IN FIBERS CONTAINING BRAGG GRATINGS Igor Fedin Thesis Approved: Accepted: ______________________________ ______________________________ Advisor Dean of the College Dr. Sergei F. Lyuksyutov Dr. Chand K. Midha ______________________________ ______________________________ Faculty Reader Dean of the Graduate School Dr. David S. Perry Dr. George R. Newkome ______________________________ ______________________________ Department Chair Date Dr. Robert R. Mallik ii ABSTRACT The temperature dependence of thermo-optic coefficient in silica-based fibers containing fiber Bragg gratings (FBGs) includes thermal instability of chemical composition gratings, non-linear temperature dependence of FBGs written in different fibers, quadratic behavior of FBGs, and long-term stability of silica-based FBGs. Experimental measurements of the thermo-optic coefficient for the temperature interval 50 – 7800C in fused silica fiber containing FBGs were conducted while the temperature shift of the Bragg’s peak was monitored between 1300 and 1311 nm with sub-Angstrom precision. Numerical computations were focused on the FBG’s diffraction efficiency calculations accounting for the temperature drift of the gratings and found to be in excellent agreement with obtained experimental data. It has been found that the thermo- optic coefficient changes between 0.79×10-5 and 1.45×10-5 K-1 and undergoes a minimum in the vicinity of 440°C. Additional observation indicates a negative sign of the second- order thermo-optic coefficient.
    [Show full text]
  • Euroresearch & Consulting
    Euroresearch & Consulting LLC Market Research: Global Market for Germanium and Germanium Products. 1 CONTENTS CHAPTER 1. GENERAL REVIEW OF THE INDUSTRY. ......................................................... 5 1.1. HISTORIC, PRESENT AND ESTIMATED CORRELATION OF GLOBAL GERMANIUM DEMAND AND SUPPLY. ................................................................................................................... 5 1.2. ANALYSIS OF PRICES ON GERMANIUM............................................................................ 13 1.3. GENERAL SIZE OF THE MARKET AND PRINCIPAL SEGMENTS OF GERMANIUM CONSUMPTION AND GERMANIUM CONTAINING PRODUCTS. ........................................... 31 1.4. THE MAIN TRENDS OF GERMANIUM PRODUCTION AND CONSUMPTION. ............. 38 1.5. THE PRINCIPAL FACTORS HAMPERING INDUSTRY DEVELOPMENT AND MARKET GROWTH. .......................................................................................................................................... 47 1.6. THE ANALYSIS OF THE IMPACT OF ACTUAL AND POTENTIAL ECONOMIC SANCTIONS ON THE INDUSTRY. ................................................................................................. 48 CHAPTER 2. THE PRINCIPAL FIELDS OF GERMANIUM APPLICATION: ANALYSIS OF MAJOR TRENDS AND AVENUES. ........................................................................................... 50 CHAPTER 3. THE ANALYSIS OF THE INDUSTRY OF PRODUCTION OF GERMANIUM AND ITS DERIVATIVES ACCORDING TO PORTER 5 COMPETITIVE FORCES MODEL. ..............................................................................................................................
    [Show full text]
  • Chemical Names and CAS Numbers Final
    Chemical Abstract Chemical Formula Chemical Name Service (CAS) Number C3H8O 1‐propanol C4H7BrO2 2‐bromobutyric acid 80‐58‐0 GeH3COOH 2‐germaacetic acid C4H10 2‐methylpropane 75‐28‐5 C3H8O 2‐propanol 67‐63‐0 C6H10O3 4‐acetylbutyric acid 448671 C4H7BrO2 4‐bromobutyric acid 2623‐87‐2 CH3CHO acetaldehyde CH3CONH2 acetamide C8H9NO2 acetaminophen 103‐90‐2 − C2H3O2 acetate ion − CH3COO acetate ion C2H4O2 acetic acid 64‐19‐7 CH3COOH acetic acid (CH3)2CO acetone CH3COCl acetyl chloride C2H2 acetylene 74‐86‐2 HCCH acetylene C9H8O4 acetylsalicylic acid 50‐78‐2 H2C(CH)CN acrylonitrile C3H7NO2 Ala C3H7NO2 alanine 56‐41‐7 NaAlSi3O3 albite AlSb aluminium antimonide 25152‐52‐7 AlAs aluminium arsenide 22831‐42‐1 AlBO2 aluminium borate 61279‐70‐7 AlBO aluminium boron oxide 12041‐48‐4 AlBr3 aluminium bromide 7727‐15‐3 AlBr3•6H2O aluminium bromide hexahydrate 2149397 AlCl4Cs aluminium caesium tetrachloride 17992‐03‐9 AlCl3 aluminium chloride (anhydrous) 7446‐70‐0 AlCl3•6H2O aluminium chloride hexahydrate 7784‐13‐6 AlClO aluminium chloride oxide 13596‐11‐7 AlB2 aluminium diboride 12041‐50‐8 AlF2 aluminium difluoride 13569‐23‐8 AlF2O aluminium difluoride oxide 38344‐66‐0 AlB12 aluminium dodecaboride 12041‐54‐2 Al2F6 aluminium fluoride 17949‐86‐9 AlF3 aluminium fluoride 7784‐18‐1 Al(CHO2)3 aluminium formate 7360‐53‐4 1 of 75 Chemical Abstract Chemical Formula Chemical Name Service (CAS) Number Al(OH)3 aluminium hydroxide 21645‐51‐2 Al2I6 aluminium iodide 18898‐35‐6 AlI3 aluminium iodide 7784‐23‐8 AlBr aluminium monobromide 22359‐97‐3 AlCl aluminium monochloride
    [Show full text]
  • Ternary Nitride Materials: Fundamentals and Emerging Device Applications Arxiv:2010.08058V1 [Cond-Mat.Mtrl-Sci] 15 Oct 2020
    Ternary Nitride Materials: Fundamentals and Emerging Device Applications Ann L. Greenaway,1 Celeste L. Melamed,2;1 M. Brooks Tellekamp,1 Rachel Woods-Robinson,3;4;1 Eric S. Toberer,2 James R. Neilson5 and Adele C. Tamboli1* 1Materials and Chemistry Science and Technology Directorate, National Renewable Energy Laboratory, Golden, Colorado, United States, 80401 email: [email protected] 2Department of Physics, Colorado School of Mines, Golden, Colorado, United States, 80401 3Applied Science and Technology Graduate Group, University of California at Berkeley, Berkeley, California, United States, 97402 4Energy Technologies Area, Lawrence Berkeley National Laboratory, Berkeley, California, United States, 94720 5Department of Chemistry, Colorado State University, Fort Collins, Colorado, United States, 80523 Keywords ternary nitride, structural chemistry, metastability, nitride synthesis, optoelectronics, battery Abstract Interest in inorganic ternary nitride materials has grown rapidly over the past few decades, as their diversity of chemistries and structures make them appealing for a variety of applications. Due to synthetic challenges posed by the stability of N2, the number of predicted ni- tride compounds dwarfs those that have been synthesized, offering a breadth of opportunity for exploration. This review summarizes the fundamental properties and structural chemistry of ternary nitrides, leveraging metastability and the impact of nitrogen chemical potential. A discussion of prevalent defects, both detrimental and beneficial, is followed by a survey of synthesis techniques and their interplay with arXiv:2010.08058v1 [cond-mat.mtrl-sci] 15 Oct 2020 metastability. Throughout the review, we highlight applications (such as solid-state lighting, electrochemical energy storage, and electronic devices) in which ternary nitrides show particular promise. 1 Contents 1.
    [Show full text]
  • Characterization of Iii-Nitride Thin Films
    ABSTRACT PARK, JI-SOO. Growth and Characterization of GaN and AlGaN Thin Films and Heterostructures and the Associated Development and Evaluation of Ultraviolet Light Emitting Diodes. (Under the direction of Professor Robert F. Davis) AlGaN-based thin film heterostructures have been grown and fabricated into ultraviolet light emitting diodes with and without p-type and/or n-type AlGaN carrier- blocking layers at the top and the bottom of the quantum wells, respectively, and having the principal emission at 353 nm. The highest values of this peak intensity and light output power were measured in the devices containing p-type carrier-blocking layers. Growth of an n-type carrier-blocking layer had an adverse effect on these device characteristics. A broad peak centered at ~540nm exhibited yellow luminescence and was present in the spectra acquired from all the devices. This peak is attributed to absorption of the ultraviolet emission by and re-emission from the p-GaN and/or to the luminescence from the AlGaN within quantum wells by current injection. Individual AlxGa1-xN films (x<0≤1) have been grown on Si- and C-terminated 6H-SiC{0001} substrates and characterized for electron emission applications. The large range in the values of x was achieved by changing the fraction of Al in the gas phase from 0 to 0.45. The ionized donor concentration in the n-type, Si-doped AlxGa1-xN films decreased as the mole fraction of Al was increased due to the reduction in the donor energy level and compensation. The use of the SiH4 flow rate, which yields a Si concentration of ~1 x 1019 cm-3 in GaN, established the upper limit of the mole fraction of Al wherein n-type doping could be achieved at ~0.61.
    [Show full text]