DOCSLIB.ORG

Capacitor-Based DC Uninterruptible Power Supplies Catalog Numbers 1606-XLSCAP24-6, -XLSCAP24-12 Important User Information

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Capacitor-Based DC Uninterruptible Power Supplies Catalog Numbers 1606-XLSCAP24-6, -XLSCAP24-12 Important User Information Reference Manual Original Instructions Capacitor-based DC Uninterruptible Power Supplies Catalog Numbers 1606-XLSCAP24-6, -XLSCAP24-12 Important User Information Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards. Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited Throughout this manual, when necessary, we use notes to make you aware of safety considerations. WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence. IMPORTANT Identifies information that is critical for successful application and understanding of the product. Labels may also be on or inside the equipment to provide specific precautions. SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present. BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures. ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE). Table of Contents Topic Page Topic Page Additional Resources 3 Ready and Buffer Relay Contact 15 Terminology and Abbreviations 4 Inhibit Input 16 Product Overview 5 PC-mode 16 Front Side and User Elements 6 Efficiency and Power Loss 17 Accessories 7 Lifetime Expectancy and Mean Time Between 17 Failure Protection Features 7 Functional Diagram 19 Safety Features 8 EMC 20 Installation Notes 8 Application Notes 21 Terminals and Wiring 10 Troubleshooting 26 Input 11 Specifications 26 Output 12 Environment 27 Charging 14 Standards Compliance and Certifications 28 Buffer Time 14 Approximate Dimensions and Weight 29 Additional Resources These documents contain additional information concerning related products from Rockwell Automation. Resource Description Switched Mode Power Supply Technical Data, publication Provides specifications and approximate dimensions 1606-TD002 for full line of switched mode power supplies. Industrial Automation Wiring and Grounding Guidelines, Provides general guidelines for installing a Rockwell publication 1770-4.1 Automation industrial system. Product Certifications website, http:// Provides declarations of conformity, certificates, and www.rockwellautomation.com/global/certification/ other certification details. overview.page You can view or download publications at http://www.rockwellautomation.com/global/literature-library/overview.page. To order paper copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales representative. Rockwell Automation Publication 1606-RM054A-EN-P - September 2016 3 Capacitor-based DC UPS Power Supplies Terminology and Abbreviations Term Definition Normal mode Describes a condition where the capacitor is charged, the input voltage is in range, and the output is loaded within the allowed limits. Buffer mode Describes a condition where the input voltage is below the transfer threshold level, the unit is running on capacitor (buffering) and the output is loaded within the allowed limits. Charging mode Describes a condition where the capacitor is being charged, the input voltage is in range and the output is loaded within the allowed limits. Inhibit mode Describes a condition where buffering is disabled on purpose (service actions) AC 24V A figure displayed with the AC or DC before the value represents a nominal voltage with standard tolerances included. For example, DC 12V describes a 12V battery disregarding whether it is full (13.7V) or flat (10V) 24V AC A figure with the unit (V AC) at the end is a momentary figure without any additional tolerances included. DC-UPS Direct Current- Uninterruptible Power Supplies ELDC Electrochemical Double Layer Capacitors EMC Electromagnetic Compatibility VRLA Valve-regulated Lead-acid PELV Protected Extra-low Voltage SELV Separated Extra-low Voltage 4 Rockwell Automation Publication 1606-RM054A-EN-P - September 2016 Capacitor-based DC UPS Power Supplies Product Overview Bulletin 1606 DC- Uninterruptible Power Supplies (DC-UPSs) use electrochemical double-layer capacitors (EDLC), commonly known as ultracapacitors or supercapacitors, that are installed inside. They can bridge power failures or voltage fluctuation and supply voltage to the DC 24V bus for a certain period, which allows for a controlled shut-down of the system. Expensive downtimes, long restart cycles, and loss of data can be avoided. The power supply provides sufficient voltages, the DC-UPS stores energy in the capacitors. If there is a mains voltage fault, this energy is released to the DC bus in a regulated process. The DC-UPSs require no maintenance and have a similar lifetime expectancy as standard power supplies. No regular replacement of the capacitors is necessary as is required for battery-based DC-UPS systems. The wide temperature range makes the unit suitable for many applications. Two versions of the DC-UPSs are available and differ by the size of the installed capacitor. • Built-in capacitors as energy source, EDLC • Wide temperature range: -40…+60 °C (-40…+140 °F) • Typically >10 years operational lifetime expectancy •Regulated output voltage in Buffer mode • No ventilated cabinets required, no generation of hydrogen as valve- regulated lead-acid (VRLA) batteries do • Active balancing for longest life and buffer times • Short charging time, unit is rapidly back in Ready mode • Output is decoupled from the input to separate load • Circuits into buffered and non-buffered sections • Supports PC-mode function • One year warranty Rockwell Automation Publication 1606-RM054A-EN-P - September 2016 5 Capacitor-based DC UPS Power Supplies Front Side and User Elements Figure 1 - Front Side of DC-UPS A. Input Terminals (quick-connect spring-clamp terminal) B. Output Terminals (quick-connect spring-clamp terminal) Minus-pole has the same reference as the minus-pole of the input terminals C. Signal Connector (plug connector) • Ready: contact is closed when status indicator shows ready • Buffering: contact is closed during buffering • Inhibit: a voltage applied on this input signal disables buffering (during service) • PC-mode: To activate the PC-mode connect the two pins of the signal connector together (See PC-mode on page 16) D. Status Indicator (green) Figure 2 • Ready: capacitors are fully charged, no failures detected. • Charging: capacitors are being charged • Buffering: capacitors are being discharged Figure 2 - Updating pattern for the green E. Diagnosis status indicator (yellow) Figure 3 status indicator 1 Ready 0 Helps troubleshooting and indicates the following: 1 0 Charging 1 • Current Overload: output voltage below 20V DC due to a too high 0 Buffering output current, ready contact is open • High Temperature: signals capacitor temperature is too high(>65 ºC), charging and buffering is still possible, ready contact is open • Buffer Time Expired: buffering stopped due to discharged capacitors - Inhibit Active: buffering is blocked by the inhibit signal Figure 3 - Updating Pattern for the Yellow F. Warning status indicator (red) Figure 4 Diagnosis Status Indicator: 1 Current • Check Input Voltage: Indicates a too low or too high input voltage. The 0 Overload input voltage must be between 23V DC and 30V DC to turn-on the 1 High Temperature 0 output and to start charging of the capacitors. 1 Buffer time 0 expired • PC-mode activated indicates, that the PC-mode (See PC-mode on 1 Inhibit 0 active page 16) is activated. Figure 4 - Updating pattern for the Red G. Chassis Ground (screw) Warning Status Indicator: 1 Check input Use a M4 ring-type terminal to connect the housing to ground, when
Load more

Recommended publications
  • What Is an SMPS and How Does It Generate Harmonics?
    MIRUS FREQUENTLY ASKED QUESTIONS FAQ’s___ International Inc. 6805 Invader Cres., Unit #12, Mississauga, Ontario, Canada L5T 2K6 Harmonic Mitigating Transformers <Back to Questions> 4. What is an SMPS and how does it generate harmonics? The Switch-mode Power Supply (SMPS) is found in most power electronics today. Its reduced size and weight, better energy efficiency and lower cost make it far superior to the power supply technology it replaced. Electronic devices need power supplies to convert the 120VAC receptacle voltage to the low voltage DC levels Rectifier Lls that they require. Older generation power supplies used Bridge large and heavy 60 Hz step-down transformers to i convert the AC input voltage to lower values before ac Smoothing Switch-mode rectification. The SMPS avoids the heavy 60 Hz step- vac Capacitor dc-to-dc Cf converter down transformer by directly rectifying the 120VAC Load using an input diode bridge (Figure 4-1). The rectified voltage is then converted to lower voltages by much smaller and lighter switch-mode dc-to-dc converters using tiny transformers that operate at very high Figure 4-1: Typical circuit diagram of Switch-mode Power frequency. Consequently the SMPS is very small and Supply light. The SMPS is not without its downside, however. The operation of the diode bridge and accompanying smoothing capacitor is very non-linear in nature. That is, it draws current in non-sinusoidal pulses at the peak of the voltage Voltage waveform (see Figure 4-2). This non-sinusoidal current waveform is very rich in harmonic currents. Because the SMPS has become the standard computer power supply, they are found in large quantities in commercial buildings.
    [Show full text]
  • EE 462: Laboratory # 4 DC Power Supply Circuits Using Diodes (Lab 3 Report Due at Beginning of the Period) (Pre-Lab4 and Lab-4 D
    EE 462: Laboratory # 4 DC Power Supply Circuits Using Diodes by Drs. A.V. Radun and K.D. Donohue (2/14/07) Department of Electrical and Computer Engineering University of Kentucky Lexington, KY 40506 Updated by Stephen Maloney (2/12/08) (Lab 3 report due at beginning of the period) (Pre-lab4 and Lab-4 Datasheet due at the end of the period) I. Instructional Objectives Design and construct circuits that transform sinusoidal (AC) voltages into constant (DC) voltages. Design and construct a voltage regulator based on the characteristics of the Zener diode. Evaluate the performance of simple rectifier and regulator circuits. See Horenstein 4.3 and 4.4 II. Background Electric power transmits best over long distances at high voltages. Since P = I V, a larger voltage implies a smaller current for the same transmitted power. And smaller currents allow for the use of smaller wires with less loss. The high voltages used for power transmission must be reduced to be compatible with the needs of most consumer and industrial equipment. This is done with transformers that only operate with AC (DC does not pass through a transformer). However, most electronic devices powered by a home outlet require DC (constant) voltages. Therefore, the device must have a power supply that converts AC voltages into a DC (constant) voltage. The terminology "DC" is somewhat ambiguous. DC can mean the voltage or current always has the same polarity but changes with time (pulsating DC), or it can mean a constant value. In this lab assignment DC will refer to a constant voltage or current.
    [Show full text]
  • Custom Power Supplies, Transformers, Chokes & Reactors
    YOUR POWER SOURCE Custom Power Supplies, Transformers, Chokes & Reactors NeeltranThe Story Transformers and Power Supplies • Industry Leader since 1973 Neeltran has become the most reliable supplier of Transformers and Power Supply Systems in the industry. Our engineers, along with our manufacturing team, have the knowledge and ability to meet the special needs of our customers. All power supplies are custom designed to your specifications by our engineering staff and completely fabricated in-house at our manufacturing facility. Our facilities and experience include: • Research & Development Since 1973 Neeltran has been a leading • Test Laboratory manufacturer of transformers and • Design Engineering power supplies. • Printed Circuit Board Manufacturing Our general product range is: • Steel Cutting Machinery • Dry Type and Water Cooled Transformers: • Baking Ovens 5–10,000 KVA (up to 25 KV input) • Vacuum Pressure Impregnation Tanks (Outputs up to 300 KV and 50 KHZ) • Coil Winding Equipment • Oil filled Transformers (Rectifier type only): 100 KVA to 50 MVA (up to 69 KV input) • Painting and Steel Fabrication to manufacture our own enclosures • Oil filled high frequency Transformers: • Assembly Areas up to 50 KHZ, 2000 KVA, up to 50 KV output Industry standards are maintained with our • Cast Coil Transformers: up to 20 MVA testing equipment assuring that all shipped (up to 35 KV input) products meet customer’s requirements and • Chokes and Reactors air or iron: specifications. Impulse testing as well as customer up to 25 KV, 20,000 amps specific testing is available upon request. • Power Supplies: 100 A to 500,000 amp (AC or DC) 1500 VDC. Special outputs up to 300,000 volts AC or DC and high frequencies are available.
    [Show full text]
  • Design Tips for Linear and Switched‐Mode Power Supplies
    Analog Design Journal Power Design tips for linear and switched-mode power supplies By Billy Long Systems Engineer Introduction the rate of change of flux in that conductor. Energy transmitted through the electric grid is transmit- dΦ VN= (1) ted at very high voltages to reduce the amount of copper dt lost as heat in the wires; however, most electrical and where N is the number of turns of the conductor subject electronic applications use much lower voltages. to the change in flux, Φ. One of the main reasons why the power grid uses AC The magnetic flux in a single-conductor loop = B × A, currents and voltages is that it is relatively easy to use where B is the flux density/unit area and A is the area of transformers to convert AC power from one voltage to the loop. The relationship of induced voltage to induced another. This technology was readily available during the flux density is shown by Equation 2. initial development and deployment of power grids in the (2) late 19th and early 20th centuries. ∫ V× dt = N ×Φ = NB× × A To convert the typical grid voltage of 90 VAC to 240 VAC Because the inductance (and hence impedance) of the (depending on global location) down to a lower voltage, transmission lines used in the AC grid increases with early electronic applications used a linear power supply, frequency, the operating frequency of grids around the shown in Figure 1. world was standardized in the 50- to 60-Hz range. This The line voltage is applied to a transformer, which frequency, in conjunction with the rms grid voltages converts the input voltage down to a lower voltage.
    [Show full text]
  • Switch Mode Power Supplies and Their Magnetics Tutorial
    Datatronic Switch Mode Power Supplies and their Magnetics Many factors must be considered by designers when choosing the magnetic components required in today’s electronic power supplies DATATRONIC DISTRIBUTION, INC. Datatronic In today’s day and age the most often used topology for electronic power supplies is that of the Switch Mode Power Supply (SMPS), which is a major user of magnetics. In some applications the “older type” linear supplies are still used, but in the early 70’s SMPS came into being spurred by the development of faster switching transistors. This facilitated the use of much smaller magnetic components and greater efficiencies. DATATRONIC DISTRIBUTION, INC. Datatronic SMPS and their General Magnetic Usage In general, there are four different types of magnetic components that are needed for the typical SMPS. They include the Output Transformer, usually the most noticeable because of its size compared to the others, the Output Inductors, the Input Inductors and the Current Sense Transformer, each with its own important function. DATATRONIC DISTRIBUTION, INC. Datatronic SMPS and their General Magnetic Usage 1.The Output Transformer or “Main” Transformer takes the input voltage that is supplied to its primary winding and then transforms the input voltage to one or more voltages that are the output of the secondary winding or windings. 2. The Output Inductors are used to filter the output voltage so that the load “sees” a filtered DC voltage. DATATRONIC DISTRIBUTION, INC. Datatronic SMPS and their General Magnetic Usage 3. The Input Inductors filter out the noise generated by the switching transistors so that this noise isn’t emitted back to the source.
    [Show full text]
  • How to Select a Capacitor for Power Supplies
    CAPACITOR FUNDAMENTALS 301 HOW TO SELECT A CAPACITOR FOR POWER SUPPLIES 1 Capacitor Committee Upcoming Events PSMA Capacitor Committee Website, Old Fundamentals Webinars, Training Presentations and much more – https://www.psma.com/technical-forums/capacitor Capacitor Workshop “How to choose and define capacitor usage for various applications, wideband trends, and new technologies” The day before APEC, Saturday March 14 from 7:00AM to 6:00PM Capacitor Industry Session as part of APEC “Capacitors That Stand Up to the Mission Profiles of the Future – eMobility, Broadband” Tuesday March 17, 8:30AM to Noon in New Orleans Capacitor Roadmap Webinar – Timing TBD – Latest in Research and Technology Additional info here. Short Introduction of Today‘s Presenter Eduardo Drehmer Director of Marketing FILM Capacitors Background: • Over 20 years experience with knowledge on +1 732 319 1831 Manufacturing, Quality and Application of Electronic Components. [email protected] • Responsible for Technical Marketing for Film Capacitors www.tdk.com 2018-09-25 StM Short Introduction of Today‘s Presenter Edward Lobo was born in Acushnet, MA in 1943 and graduated from the University of Massachusetts in Amherst in 1967 with a BS in Chemistry. Ed worked for Magnetek, Aerovox and CDE where he is currently Chief Engineer for New Product Development. Ed Lobo Ed has served for over 52 years in Chief Engineer, New Product capacitor product development. He holds [email protected] 14 US patents involving capacitors. 4 ABSTRACT This presentation will guide individuals selecting components for their Electronic Power Supplies. Capacitors come in a wide variety of technologies, and each offers specific benefits that should be considered when designing a Power Supply circuit.
    [Show full text]
  • Aluminum Electrolytic Capacitors Power Application Capabilities
    VISHAY INTERTECHNOLOGY, INC. aluMinuM electrolYtic capacitors Power Application Capabilities Aluminum Electrolytic Capacitors in Power Applications POWER APPLICATIONS • Motor Drives • Solar Inverters • Traction in trains or rolling stock • Uninterruptible Power Supply (UPS) • Pulsed Power RESOURCES • For technical questions contact [email protected] • Sales Contacts: http://www.vishay.com/doc?99914 A WORLD OF SOLUTIONS CAPABILITIES 1/11 VMN-PL0453-1610 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 www.vishay.com VISHAY INTERTECHNOLOGY, INC. aluMinuM electrolYtic capacitors for Motor Drives Introduction to the Application Motor drives are used to control the speed of various motors in all kinds of systems, from the small pumps and motors in household washing machines and central heating and air-conditioning systems to the large motors found in industrial machinery. Selecting the Best Capacitor for Your Motor Drive Application Aluminum capacitors are often used as DC link capacitors in motor drives, both in 1-phase and 3-phase designs. The aluminum capacitor is used as an energy buffer to ensure stable operation of the switch mode inverter driving the motor. The aluminum capacitor also functions as a filter to prevent high-frequency components from the switch mode inverter from polluting the mains voltage. The key selection criterion for the aluminum capacitor is the required ripple current. The ripple current consists of two components, a low-frequency ripple (50 Hz to 200 Hz) from the input and a high-frequency component from the inverter, typically 8 kHz to 20 kHz.
    [Show full text]
  • AN-500: Depletion-Mode Power Mosfets and Applications
    INTEGRATED CIRCUITS DIVISION Application Note AN-500 Depletion-Mode Power MOSFETs and Applications AN-500-R03 www.ixysic.com 1 INTEGRATED CIRCUITS DIVISION AN-500 1 Introduction Applications like constant current sources, solid state relays, and high voltage DC lines in power systems require N-channel depletion-mode power MOSFETs that operate as normally-on switches when the gate-to-source voltage is zero (VGS=0V). This paper will describe IXYS IC Division’s latest N-channel, depletion-mode, power MOSFETs and their application advantages to help designers to select these devices in many industrial applications. Figure 1 N-Channel Depletion-Mode MOSFET D ID + G V + DS IG V - GS I - S S A circuit symbol for an N-channel depletion-mode power MOSFET is given in Figure 1. The terminals are labeled as G (gate), S (source) and D (drain). IXYS IC Division depletion-mode power MOSFETs are built with a structure called vertical double-diffused MOSFET, or DMOSFET, and have better performance characteristics when compared to other depletion-mode power MOSFETs on the market such as high VDSX, high current, and high forward biased safe operating area (FBSOA). Figure 2 shows a typical drain current characteristic, ID, versus the drain-to-source voltage, VDS, which is called the output characteristic. It’s a similar plot to that of an N-channel enhancement mode power MOSFET except that it has current lines at VGS equal to -2V, -1.5V, -1V, and 0V. Figure 2 CPC3710 - MOSFET Output Characteristics Output Characteristics (TA=25ºC) 300 270 VGS=0.0V 240 210 V =-1.0V 180 GS 150 (mA) D I 120 V =-1.5V 90 GS 60 V =-2.0V 30 GS 0 0123456 VDS (V) The on-state drain current, IDSS, a parameter defined in the datasheet, is the current that flows between the drain and the source at a particular drain-to-source voltage (VDS), when the gate-to-source voltage (VGS) is zero (or short-circuited).
    [Show full text]
  • Differences Between Power Supplies, Inverters, and Transformers
    Differences Between Power Supplies, Inverters, and Transformers [0m:0s] [0m:4s] Hi I'm Josh Bloom, welcome to another video in the RSP Supply education series. In today's video we're going to be looking at some of the differences between several pieces of hardware that often get confused, even though they are intended for very different purposes. This hardware includes power supplies, [0m:23s] transformers, inverters, and voltage converters. [0m:28s] All of this hardware is intended to alter or change the type of power or voltage that you might be using. [0m:35s] The result you need will directly impact which type of hardware you may want to choose. [0m:41s] However, it is very common for people to confuse the different types of hardware. Let's discuss each type and what it is intended to do so hopefully by the end of the video you'll be able to have a very clear understanding of each and when you might want to use them. Let's first start with power supplies. A power supply can have many different functions, RSPSupply www.rspsupply.com 1-888-532-2706 www.youtube.com/RSPSupply [1m:2s] but most of the time the power supply is intended to take one type of power and convert it to another type of power. The most common example of this is a power supply that takes AC power and converts it to DC power. [1m:17s] While it is very common to use power supplies and industrial applications, one very common place you will see a power supply being used is for the gadgets you have around your home, such as your smartphone or laptop or tablet, RSPSupply www.rspsupply.com 1-888-532-2706 www.youtube.com/RSPSupply [1m:31s] or many other devices we use on a daily basis.
    [Show full text]
  • Ten Fundamentals You Need to Know About Your DC Power Supply
    Keysight Technologies Ten Fundamentals You Need to Know About Your DC Power Supply Application Note Introduction Understanding how measurement tools operate can provide insight into how to improve testing methods. With modern performance and safety features in power supplies, the lexibility exists to create test setups that are simpler and more effective. Use these 10 fundamentals about your power supply to take advantage of these features. Contents 1 Program Your Power Supply Correctly to Operate in Constant Voltage or Constant Current Mode / 3 2 Use Remote Sense to Regulate Voltage at Your Load / 4 3 Use Your Power Supply to Measure DUT Current / 5 4 Connect Power Supply Outputs in Series or Parallel for More Power / 6 5 Minimize Noise From Your Power Supply to Your DUT / 7 6 Safeguard Your DUT Using Built-in Power Supply Protection Features / 8 7 Use Output Relays to Physically Disconnect Your DUT / 9 8 Capture Dynamic Waveforms Using a Power Supply’s Built-in Digitizer / 10 9 Create Time-Varying Voltages Using Power Supply List Mode / 11 10 Tips for Rack-Mounting Your Power Supply / 12 Glossary / 13 Resources / 14 2 DC Power Supply Fundamentals Program your Power Supply Correctly to Operate 1 in Constant Voltage or Constant Current Mode The output of a power supply can operate current limit setting. This operating mode Possible causes of UNR include: in either constant voltage (CV) mode or is known as constant current (CC). In –The power supply has an constant current (CC) mode depending on Figure 1, the power supply will operate on internal fault.
    [Show full text]
  • MOSFET Gate Drive Circuit Application Note
    MOSFET Gate Drive Circuit Application Note MOSFET Gate Drive Circuit Description This document describes gate drive circuits for power MOSFETs. © 2017 - 2018 1 2018-07-26 Toshiba Electronic Devices & Storage Corporation MOSFET Gate Drive Circuit Application Note Table of Contents Description ............................................................................................................................................ 1 Table of Contents ................................................................................................................................. 2 1. Driving a MOSFET ........................................................................................................................... 3 1.1. Gate drive vs. base drive.................................................................................................................... 3 1.2. MOSFET characteristics ...................................................................................................................... 3 1.2.1. Gate charge ........................................................................................................................................... 4 1.2.2. Calculating MOSFET gate charge ....................................................................................................... 4 1.2.3. Gate charging mechanism ................................................................................................................... 5 1.3. Gate drive power ................................................................................................................................
    [Show full text]
  • EXP4: Rectifiers
    EXP4: Rectifiers OBJECTIVES. The general objective of this experiment is for you to become familiar with the response of a diode in a circuit, whether the circuit is supplied with a DC, AC or AC-DC voltage. In this part we will also see how to couple AC and DC sources, and finally we will illustrate the use of diodes in rectifying circuits. INTRODUCTION AND TEST CIRCUITS. The circuits we will be studying are the basic limiting circuit, half-wave and full-wave rectifiers. We will be doing the analysis of the circuits using aproximation, such as assuming we know the diodes’ voltage Vf . Also we will make use of the graphical method to find the voltage and current in the diode. We will run a bias analysis using PSpice which is the same as using an iterative method. And finally we will measure in lab the actual voltage and current values. That way we will be able to evaluate the accuracy of the different methods. We will also get the transfer characteristic, and use it to predict the output waveform for a given input. We will check our estimate using PSpice and in lab. For theory on the behavior of the circuits we will be studying please refer to the textbook or some book that covers the topics, limiting and rectifying circuits. PREPARATION. For the first two circuits, the limiting and the half-wave rectifier we will do the analysis using different methods. If you are not familiar with any of these methods please refer to the textbook or some book that covers this topic.
    [Show full text]