Removal and Lnstallation of Torsion Bar on Rear Axle (Diagonal Swing Axle) 32.1

Removal and lnstallation of Torsion Bar on Rear Axle (Diagonal Swing Axle) 32.1 Data Model Torsion Bar Rubber mount on torsion bar mounting Part No. I Oiameter PartNo. I Aoredia. I 107 326 20 65 1 ) 19 107 326 14 81 17.5-0.5 107 .024 (USA) 107 .044 (USA) 107 326 23 6521 1B 1 16 326 0B 81 16.5-0.5 1) Previous version 2) Present version Tightening torques Nm (kpm) Hexagonal bolts of torsion bar mounting M 12x 1.5 65 (6.5) (4.5) Ball joints f or torsion bar connecting rods M 10 45 Removal 3 D isconnect connecting rod ( 1 5) on right and lef t of torsion bar (Fig. 2l . 1 Jack vehicle up at rear. 2 On veh icles with level control , sepa rate con nect i ng rod l\ for level control (3) from the lever (6) on the torsion bar (Fig. 1). Fig.2 Fig. 1 1 0 Torsion bar 18 Rear spring pump level control 15a Ball joint of 23 Supplementary rubber sPring 81 Pressure line oil - (buffer 82 Pressure line level control spring-loaded brake unit connecting rod stop) - 16 Def lection plate C Return line level control - oil reservoir 7 Co n nect i ng rod 3 Level control (13) on and left of 3a Level control lever B Level control holder 4 Unscrew retaining clamp right 6 Lever on torsion bar 10 Torsion bar torsion bar mounting (Fig. 3). e Ax les Vo lu me 1 Supplement 4 Modification April 7 4 31011 at tt 1 Removal and lnstallation of Torsion Bar on Rear Axle 51.1 (Diagonat Swing Axte) lnstallation 8 Check the rubber mount (12) of the torsion bar mounting and the connecting rods (1 5) (Figs. 5 and 6). I lf applicable, mount the lever for activating the level control on the torsion bar (32.3-660). 10 lnsert torsion bar. Push the rubber mount onto the torsion bar with the slit uppermost. On types 114, 1 15, put the upper retaining clamp on top (Figs. 5 and 6). Fig. 3 5 Shock absorber 17 Rubber mount for rear 10 Torsion bar spring 13 Retaining clamp 1B Rear spring for torsion bar 19 Control arm 5 On types 1 14, 1 15, disconnect the breather pipes from the fuel tank. Unscrew the fuel supply and return line clamp from the frame floor in front of the fuel tank. Detach the f ront f uel tank fastening, lower f uel tank slightly and support with a suitable prop (46) (Fig.4). R 32 -5636 Fig. 5 Type 1 07 1 0 Torsion bar 15a Ball joints of connecting 12 Rubber mount rod with sprine washers 13 Retaining clamp 16 Def lection plate 15 Connecting rod Fig. 4 10 Torsion bar 24 Fuel tank 15 Connecting rod 25 Breather pipes 19 Control arm for fuel tank 23 Supplementary rubber 46 Prop spring (buffer stop) 6 Detach the rubber r:ings of rear exhaust system attach ment, lower exhaust pipe slightly and support. Fis.6 Types 114,115 7 Remove torsion bar downwards on type 107 and 10 Torsion bar 13 Lower retaining clamp R nt 14 retaining clamp to the left vehicle side on types 114, 1 15. 12 ubber mou Upper 31012 Removal and lnstallation of Torsion Bar on Rear Axle r.l ft I (Diagonal Swing Axle) 5 Z.l 11 lnstall torsion bar mounting on f rame f loor 14 Mount rear exhaust pipe. (Figs.7 and B). 15 Lower veh icle. 12 Attach connecting rods to right and left of torsion bar (Figs. 7 and B). lf applicable, renew def lect- 16 Add itionally on veh icles with level control . ion plates. a) Hook connecting rod (7lrto the lever (6) on the 13 On types 1 14, 1 1 5, connect breather pipes Q5\ torsion bar (F ig. 1 ). to the f uel tank. Attach f uel supply and return line clamp on the frame floor in front of the fuel tank. b) Check vehicle level and correct if necessary Retighten fuel tank. @0.1 -310). Fis. 7 Type 1 07 i 0 Torsion bar 13 Retaining clamp 15a Ball joints of connecting rod 16 Def lection plate 12 Rubber mou nt 15 Connecting rod with spring washers 16 15 i I( o @ Fis. B Types 114,115 10 Torsion bar 13 Lower reta in ing cla mp 1 5 Co n nect ing rod 16 Deflection plate 12 Rubber mou nt 14 Upper retaining clamp 15a Ball pin with spring disc 19 Contro I arm .Ls Axles Volume 1 Supplement 4 Modif ication April 7 4 310/3.

Load more