DOCSLIB.ORG

Inst-Book-6260Qc.Pdf

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Inst-Book-6260Qc.Pdf INSTRUCTION BOOK IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be followed, including the followings: Read all instructions before using this appliance. DANGER— To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning. 2. Always unplug before replacing a sewing machine bulb. Replace bulb with same type rated 12 Volts, 5 Watts. WARNING— To reduce the risk of burns, fire, electric shock, or injury to persons: 1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near children. 2. Use this appliance only for its intended use as described in this owner’s manual. Use only attachments recommended by the manufacturer as contained in this owner’s manual. 3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return this sewing machine to the nearest authorized dealers or service center for examination, repair, electrical or mechanical adjustment. 4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine and foot controller free from accumulation of lint, dust and loose cloth. 5. Never drop or insert any object into any opening. 6. Do not use outdoors. 7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered. 8. To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet. 9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 10. Keep fingers away from all moving parts. Special care is required around the sewing machine needle. 11. Always use the proper needle plate. The wrong plate can cause the needle to break. 12. Do not use bent needles. 13. Do not pull or push fabric while stitching. It may deflect the needle causing it to break. 14. Switch this sewing machine off (“0”) when making any adjustment in the needle area, such as threading the needle, changing the needle, threading the bobbin or changing the presser foot, and the like. 15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or when making any other adjustments mentioned in this owner’s manual. SAVE THESE INSTRUCTIONS TABLE OF CONTENTS Name of Parts ............................................................ 2 Overcasting .............................................................. 22 Standard Accessories and Storage ............................ 3 • Zigzag stitch .................................................... 22 Extension Table and Free Arm Sewing ..................... 4 • Multiple zigzag stitch (Tricot stitch) .................. 22 GETTING READY TO SEW • Knit stitch ......................................................... 22 • Overedge stitch ................................................ 23 Connecting to the Power Supply................................ 5 • Serging stitch ................................................... 23 Controlling Sewing Speed .......................................... 5 Sewing on Buttons .................................................. 24 Function Keys and Buttons ........................................ 6 Automatic Buttonhole .......................................... 25-31 Reverse stitch button ......................................... 6 • Corded buttonhole ................................................... 32 Auto-lock button ................................................. 6 • Zipper Application ............................................... 33-35 Needle Up/Down button ..................................... 6 • Rolled Hem .............................................................. 36 Dropping the Feed Dog .............................................. 7 Eyelet ....................................................................... 36 Adjusting the Foot Pressure....................................... 7 Blind Hem Stitch ...................................................... 37 Changing the Presser Foot ........................................ 8 Darning .................................................................... 38 Detaching and Attaching the Foot Holder .................. 8 Raising and Lowering the Presser Foot ..................... 9 SEWING APPLICATION AND DECORATIVE Balancing Thread Tension.......................................... 9 STITCHES • Auto tension ....................................................... 9 Appliqué ................................................................... 39 • Manual tension adjustment ................................ 9 Quilting ..................................................................... 39 Changing the Needle ............................................... 10 Pin Tucking .............................................................. 40 Selecting Threads and Needles ............................... 10 Patchwork ................................................................ 40 Winding the Bobbin .................................................. 11 Fagoting ................................................................... 41 • Removing the Bobbin ...................................... 11 Scallop Stitch ........................................................... 41 • Winding the Bobbin .......................................... 11 Smocking ................................................................. 42 • Inserting the Bobbin ......................................... 12 Decorative Satin Stitches ......................................... 42 Threading the Machine ............................................ 13 Pattern Combination ................................................ 43 • Threading the needle thread ............................ 13 Cross Stitch .............................................................. 43 Automatic Needle Threader ..................................... 14 Cording .................................................................... 44 Drawing Up Bobbin Thread ...................................... 15 Elastic Stretch Stitch ................................................ 44 Selecting the Stitch Pattern ...................................... 16 Decorative Stretch Stitch ......................................... 45 Adjusting Stitch Width .............................................. 16 Adjusting Stretch Stitch Balance .............................. 45 Adjusting Stitch Length ............................................ 16 CARE OF YOUR MACHINE UTILITY STITCHES Replacing the Light Bulb .......................................... 46 Straight Stitch ........................................................... 17 Cleaning Hook Race and Feed Dog ........................ 47 • Starting to sew ................................................. 17 PROBLEMS AND WARNING SIGNALS ...................... 48 • Changing sewing direction ............................... 17 TROUBLESHOOTING.................................................. 49 • Fastening the seam/Thread cutter ................... 17 • Adjusting the stitch length ................................ 18 • Changing the needle drop position .................. 18 • Using the seam guide lines .............................. 19 • Sewing from the edge of thick fabric ................ 19 Variety of straight stitches ........................................ 20 Basic Zigzag Stitch .................................................. 21 • Adjusting the stitch width ................................. 21 • Adjusting the stitch length ................................ 21 1 Name of Parts 15 14 17 12 11 10 9 13 8 16 7 1 Speed control lever 2 Direct pattern selection keys 18 6 3 Stitch width control keys 4 Stitch length control keys 5 LED display 5 6 Bobbin winder stopper 7 Bobbin winder spindle 4 8 Accessory storage compartment 9 Spool pin 3 19 10 Spool holder 2 11 Stitch reference chart 20 12 Top cover 13 Hole for additional spool pin 21 1 14 Bobbin winder thread guide 22 15 Thread guide A 31 23 30 16 Thread guide B 29 28 17 Tension control dial 24 27 26 18 Foot pressure control dial 25 19 Thread take-up lever 20 Faceplate 34 21 Thread cutter 22 Automatic needle threader 23 Needle plate 24 Extension table 25 Accessory storage box 26 Hook cover plate 35 27 Hook cover plate release button 32 28 Stitch balance adjusting dial 29 Reverse stitch button 37 30 Auto lock button 36 33 31 Needle Up/Down button 32 Drop feed lever 33 Zigzag foot 34 Needle clamp screw 44 35 Needle 38 36 Presser foot holder 37 Carrying handle 43 38 Handwheel 39 Power switch 40 Machine socket for power cord 42 41 Machine socket for foot control 42 Free arm 43 Buttonhole lever 44 Presser foot lifter 39 NOTE: The design and specifications are subject 41 40 to change without prior notice. 2 5 4 Standard Accessories and Storage 1 A: Zigzag foot (set in the machine) G 2 F: Satin stitch foot 3 3 C: Overedge foot D 4 D: Rolled hem foot 5 G: Blind hem foot C 2 6 R: Automatic buttonhole foot F A 1 6 Accessory storage box 17 Accessories are conveniently stored in the storage box. 10 7 12 Draw out the storage box by pulling the dent on the box to the left. 7 Accessory storage box 20 8 E: Zipper foot 16 9 L: Quilting bar 10 Set of needles 15 11 Screwdriver 18 12 Bobbins 13 Seam ripper (Buttonhole opener) 14 Lint brush 15 Additional spool pin 9 16 Felt 17 Spool holder (Large) (set on the 13 8 19 spool pin 18 Spool
Load more

Recommended publications
  • Taking Your Measurements \ I / \ I / ' ------/ / ' ,,,__
    • 1mp s __ ...,... ___ _. _____ ___ ,,.­ -, Bulletin 498 / January 1956 / ' : TAKING YOUR MEASUREMENTS \ I / \ I / ' ------ / / ' ,,,__..... --- ------- ./ _,."' / / --- --- 1 -------------- \ \ ' A good looking dress is a well-fitted dress. Achieving a good fit depends upon three things: knowing your own figure measurements, selecting the size and type pattern which most nearly corres­ ponds to your measurements, and then making any necessary alterations in the pattern before cutting your dress. This leaflet tells you how to take your measurements and provides a place for you to record them. What Is A Well-fitted Dress? A dress that fits you well adapts itself to your body. Ir brings out your good points and skillfully hides your poor ones. You will know a good fit by- Direction of grain of fabric. - Crosswise yarns are parallel to the floor at the center-front and back busdine, and at the hipline, unless the dress has unusual style details. lengthwise yarns are at right angles to the floor at the center-front and back of both skirt and bodice of a dress. lengthwise yarns on the sleeve cap lie in the direction of the arm when it hangs straight at the side . This varies slightly on different figures but in general the crosswise yarns are also parallel are straight in front and back of your arm except to the floor. when special style features, such as extended shoul­ Direction of seam lines. - Seam lines that ders, requir.e otherwise. lie and hang straight keep your dress in proper li~e The waistline seam appears to be straight around on your figure.
    [Show full text]
  • Sewing Technique: Lock Stitch (Hem 1”)
    Sewing Technique: Lock Stitch (Hem 1”) The lock stitch is a hand stitch used for hemming purposes. It gives a secure hold with limited view of the thread on the outer side of the garment. STEP 1: Stay stitch ¼-inch from the fabric edge. (A stay stitch is a single line that is used for guidance and to keep the fabric from fraying. It is a normal stitch length and backstitching is a personal preference.) STEP 2: Fold the hem edge back 1-inch. Press fold in order to make a crease in the fabric. Press fabric 1 again ¼-inch. This press will follow the stay stitch seam. STEP 3: Secure thread to the folded edge of fabric on stay stitch line in order to hide the knot. STEP 4: Moving left, make a small stitch (1/2 to ¾ inch). The stitch should first go through the ¼-inch fold; then a small stitch is made that only goes through the outside layer of the garment. Pull thread gently back through to the inside of the garment. Avoid pulling the thread tight as the needle passes back through the loop created from the stitch. 5 3 5 STEP 6: To tighten lock stitch, pull thread to the left. STEP 7: Continue moving left and repeating step 5 until seam is complete. STEP 8: Once finished, secure thread to prevent it from unraveling. NOTE: The lock stitch can be used in place of a catch stitch. 7 6 Industry Standards for a Well-Constructed Hem: • Hem is level • Hem lies flat • No puckers, twists, or extra bulk • Hand stitching is not visible on correct side of garment • Hand stitches are evenly spaced • Topstitching is even and parallel to hemline References: Readers Digest.
    [Show full text]
  • Tailoring Series TECHNIQUES for TAILORING UNDERLINING a TAILORED GARMENT—Underlining Is a Second Layer of Fabric. It Is Cut By
    tailoring series TECHNIQUES FOR TAILORING UNDERLINING A TAILORED GARMENT—Underlining is a second layer of fabric. It is cut by the garment pattern pieces and staystitched to the wrong side of the corresponding outer sections before any seams are joined. The two layers are then handled as one. As a general guide, most suit jackets and coats look more pro- fessional when underlined. Underlining is especially recommended for lightweight wool materials, loosely woven materials and light- colored materials. For additional information on selecting fabrics for underlining and applying the underlining, see Lining a Shirt 01' Dress HE 72, N. C. Agricultural Extension Service. STAYSTITCHING—Staystitch all outer garment pieces before construction begins. If garment is underlined, stays-titching is done when the two layers of fabric are sewn together. Staystitch 1/3 in. outside seamline (on the seam allowance). Stay- stitch “ with matching cotton thread on all curved *areas that may stretch during construction such as necklines, side seams, shoulder seams, armholes, and side seams of skirt. Use directional stitching always to prevent stretching of fabric and to prevent one layer of fabric from riding. The direction to stitch is indicated by small arrows on the pattern on the seamlines. INTERFACINGS—Select a high quality hair canvas for the front and collar of coats and jackets. The percentage of wool indicates the quality—the higher the wool content of the canvas the better the quality. Since a high percentage of wool makes the hair canvas fairly dark in color, it cannot be used successfully under light-colored fabrics. In these cases use an interfacing lighter in color and lower in wool content.
    [Show full text]
  • Placket Construction Options
    Placket Construction Options 1 Type1: Two Separate Bound Edges on a rectangular stitching box The key to this structure is that the bindings are initially stitched only to the seam allowances on each side, and NOT stitched across the end, of the clipped box, which means that they, and the clipped triangle at the bottom, remain loose and can be arranged before the nal nishing to go on either side of the fabric, as well as either over or under the other, after joining them at the sides. The widths and lengths of the bindings and the space between the sides of the clipped box determine all the other options available in this most exible of all the placket types I know of. Variation 1: Both bindings t inside the stitching box If you cut the bindings so the nished, folded widths of both are equal to or smaller than the space between the initial stitching lines, as shown above, you can arrange both ends at the clipped corners to all go on one side of the fabric (right or wrong side), along with the clipped triangle on the garment. You’ll get the best results if the underlapping binding is slightly smaller than the overlapping one. This can be man- aged by taking slightly deeper seam allowances when you join this piece, so they can initially be cut from the same strip. Or, you can place one end on each side with the Both ends on RS One end on RS, Both ends on WS triangle sandwiched in between.
    [Show full text]
  • 'L::C Make a Gathered Skirt
    H7l.f -·'1~ 'l::c Make A Gathered Skirt CIRCULAR 580 OCTOBER 1964 AGRICULTURAL EXTENSION SERVICE VIRGINIA POLYTECHNIC INSTITUTE BLACKSBURG, VIRGINIA Make a Gathered Skirt Prepared by MarrJaret Groseclose, Err:tension ClothinrJ Specialist •Many girls like gathered skirts and they Make a Placket • are easy to make. Plump girls look best in 1. Work with the side seam where the gored skirts. When you make a gathered opening was left for the placket. skirt, you learn to make seams, put in a 2. Fold back the front placket extension placket, fit a waistband, hem a skirt, and put to the seam line. Press and pin. on a fastener. You study what to look for in 3. Machine stitch the length of the placket choosing a fabric and how to prepare it for opening 5/ 8" from the folded edge. Stitch cutting a garment. This will help you in diagonally to the folded edge (or seam line), making other garments. catching the back extension. 4. Clip the back seam allowance almost Supplies You Will Need to the stitching line, approximately 1/2" be- low the end of the placket. Include a sewing box, thread to match 5. Press the side seams open. background of fabric, hooks and straight eyes, 6. Two snap fasteners may be used to i:maps, and fabric. The amount of fabric keep the placket closed. needed will be twice the length of your skirt, including 3" for hem plus 5" for waistband. Figure 2 Measure and Cut 1. Straighten the fabric. 2. If you are using 2 lengths for the skirt, cut a 5-1/8" strip across the fabric for the band.
    [Show full text]
  • Key Details We Look for at Inspection
    Key Details We Look for at Inspection Please not that these lists are not all inclusive but highlight areas that most often cause difficulty. Additional details are included on spec sheets for individual costumes. Boys’ Costumes Achterhoek: 1. Overall appearance of costume 2. Do you have the correct hat? This is the high one. Volendam is shorter. 3. The collar extends to the edge of the shirt and can be comfortably buttoned at the neck. 4. Ring on scarf and is visible above vest. If necessary use a gold safety pin to hold the ring in place. 5. Is the scarf on the inside of the vest, front and back? 6. Shirt buttons are in the center of the front band 7. The vest closes left over right. 8. The chain is in the 2nd buttonhole from the bottom 9. Welt pockets are made correctly and in the correct position. 10. Pants clear shoes. 11. Pants have a 6” hem Marken: 1.Overall appearance of costume 2.Red shirt underneath jacket 3.Red stitching on jacket placket 4.Closes as a boy (L. over R.) 5.Pants at mid-calf when pulled straight 6.Pants down 1” from waist Nord Holland Sunday: 1. Overall appearance of costume 2. Correct hat and scarf 3. Neck - can fit 1 finger 4. 2 dickies (one solid and one striped) 5. Jacket - collar flaps lay smooth 6. Buttonholes are horizontal 7. Jacket closes as a boy (left over right) 8. Cord, hook and eye at back of pants 9. Pants clear shoes 10.6 inch hem Noord Holland Work: 1.
    [Show full text]
  • SEWING MACHINE MACHINE a CO UDRE MAQUINA DE COSER I Illlllllll Ill Illlllllllllll I MODELS 385
    OWNER'S MANUAL MANUEL D'INSTR UCTIONS MANUALDE INSTRUCCIONES SEWING MACHINE MACHINE A CO UDRE MAQUINA DE COSER I Illlllllll Ill Illlllllllllll I MODELS 385. 17026 MODELES MODELOS 385, 17828 SEARS, ROEBUCK AND CO. Dear Customer: You have iust invested in a very fine zigzag sewing machine. Before using your new Kenmore machine, please pause tor a moment and carelully read this booklet which contains instructions on how to operate and care tot your machine. Specific instructions are given on threading, tension adjustments, cleaning, oiling, etc. This wiI] help you obtain the best sewing results and avoid unnecessary service expense tot conditions beyond our control. Advice on the operation and care ot your machine is afways available at your nearest Sears Retal] Store. Please remember, if you have questions about your machine or need parts and service, always mention the model number and serial number when you inquire. Kenmore Sewing Machine Record in space provided below the model number and serial number of this appliance. The model number and serial number are located on the nomenclature plate, as identified on Page 4 of this book]eL Model No. 385. Senal No. Retain these numbers for future reference. THIS MODEL IS A CENTER NEEDLE, LOW BAR SEWING MACHINE. IMPORTANT SAFETY 4. Never operate the sewing machine with any air opening blocked. Keep ventilation openings of the sewing machine and toot controller tree trom accumulation INSTRUCTIONS of lint, dust, and loose cloth. 5. Never drop or insert any obiect into any opening, Your sewing machine is designed and constructed only for HOUSEHOLD use.
    [Show full text]
  • Intihil'jami's
    HINKLE & REASONER Slender Silhouette in Tailored Gowns PHONE MAIN 51 23—Day or Night Pool Hall & Barber Shop C IG ARB mkZM DOUGLASS UNDERTAKING COMPANY SHOES SHINED BY EXPERTS J. R. CONTEE Pres, INCOIIBORATED AND BONDED PHONE MAIN <ilsS> and Mgr. 2051 Champa Street Denver, Colorado RESIDENCE PH ONE YORK 7992. WE SAVE YOU a 0.00 Parlors, 1830 Arapahoe Street Denver, Colorado Drink Capitol Beer DENVER’S PRIDE We Deliver the Best $2O to $25 Tailor Made Suit in Denver. Best Goods. The purity of Capitol Beer is demon- Best Workmanship. Tailoring in all tailored gowns there Is little de- tion. Its thoroughly practical points INparture from the 6lender silhouette. make themselves evident. cling are strated by its superior flavor and for LADIES Skirts, with all their drapery, Combinations of two materials its Branches AND GEN= rather closely to the figure. featured in tailored gowns for spring. Coats are short In the front and A plain cloth skirt with a plaid jacket, strength-giving qualities. It’s capital. TLEMEN.. lengthen more or less toward the or a cross-barred skirt with a plain back. Many of thenf reach only a coat, or a figured material trimmed IN’ curtis street little below the waist line. Most of with checks, are bright and pleasing. Ferry, 1905 them open at the front and are fin- Perhaps the best-liked combination of HAVE A CASE SENT HOME ished with revers. The rolling, or all is that of black moire silk in bands standing collar, worn with the coat, is and flounces on cloth of a contrasting p made of fine net or lace and wired to color.
    [Show full text]
  • Measurement Chart
    Measurement Chart NAME: ___________________________________ DATE: __________________ 1. High bust circumference: 2. Full bust circumference: 2a. Distance between bust points: 3. Distance from shoulder/neck point to bust point: 4. Waist circumference: 5. High Hip circumference: 5a. Distance from waist: 6. Full hip circumference: 6a. Distance from waist: 7. Stride (crotch length) plus 1" to 2": 8. Length from waist to floor minus 1": 9. Shoulder length: 10. Upper arm circumference: 11. Sleeve length: 12. Back width: 13. Back length to waist: © The Sewing Workshop Fitting the Bust: Ease Chart Garment Minimum Bust Ease Blouse, Dress 2½" to 3" Unlined jacket 3" to 4" Lined jacket 3½" to 4½" Coat 4" to 5" Fitting the Bust: Ease Chart © The Sewing Workshop Fitting the Back: Ease Chart Garment Minimum Back Ease Blouse, Dress ½" to 1" Jacket 1" Coat 1" to 2" Fitting the Back: Ease Chart © The Sewing Workshop Fitting Sleeves: Ease Chart Garment Minimum Upper Arm Ease Blouse 1" to 1½" Dress 1½" to 2" Unlined jacket 3" to 4" Lined jacket 3" to 4½" Coat 4" to 5½" Fitting Sleeves: Ease Chart © The Sewing Workshop Fitting Pants: Ease Chart Minimum Pants Ease Waist 1" to 2" Hip 2" - Fitted Pants 4" - Elastic Waist Pants Crotch Length 1" - If hips are less than 37" 1½" - If hips are 37"-40" 2" - If hips are 40" or more Fitting Pants: Ease Chart © The Sewing Workshop How to Measure For Successful Fitting by Linda Lee Tips! Tips! Tips! Gather Your Tools Know Your Notions Two very specific tools are recommended: Elastic - Use 1”-wide Stretchrite woven polyester flat non-roll elastic.
    [Show full text]
  • Dressmaking up to Date
    PRICE, 25 CENTS or Is. PUBLISHED BY THE BUTTERICK PUBLISHING COMPANY, Limited AT THE BUTTERICK BUILDING, NEW YORK PARIS LONDON NEW YORK TORONTO Copyright, /QOj, by The Butter ick Publishing Co., Limited. Entered at Stationers’ Hall. A ll rights reserved. ■r o: ; < A Dressmaking, TUp to Date h.-K'ARV,^ rorS^BiS1 f'flsi $cp»es jits,wiYW( { . > i SfcP Hi ; « Ooiwngns umt J-^/ o2 &. I c/C61 / a 1X733! COPY f;s> . 3 FRONTISPIECE —THE SEWING CIRCLE HAND-SEWING STITCHES IMPORTANT POINTS AND AIDS IN DRESSMAKING THE CORRECT METHOD OF ALTERING PATTERNS SHIRT-BLOUSES DRAPED WAISTS SKIRTS NOVEL, ARTISTIC SEAMS WEDDING AND EVENING GOWNS THE TAILOR-MADE GOWN COATS AND JACKETS PRACTICAL AND ORNAMENTAL STITCHES BIAS BANDS AND FOLDS—TURNING CORNERS AN EMPIRE TEA-GOWN DESIRABLE GARMENTS FOR MATERNITY WEAR MAKING /ND FINISHING UNDERWEAR THE BATH-ROBE. CHILDREN’S CLOTHES BOYS’ SUITS XTlp to 5>ate inning (EirrU SDressmahtrtg, TUp to Date SIMPLE SEWING STITCE1ES AKING A KNOT.—Holding the threaded needle in the right hand, twist the end of the thread once and a half, around the forefinger of the left hand; press, roll downward on the ball of the thumb, twisting once or twice; slip off and draw down M with the middle finger of the left hand. BASTING.—There are two kinds of basting; even and uneven. In even basting the stitches; and spaces are the same length; in uneven basting, as its name implies, the stitches are so formed that they are not of equal length. EVEN BASTING STITCH.—Start with a knot in basting and always have it on the right side; it is more easily removed.
    [Show full text]
  • A Manual for Home Sewing
    Extension Bulletin 468 December 1933 Home Economics Series A Manual for Home Sewing 41, THIS BULLETIN IS PREPARED TO SERVE THREE GROUPS OF OREGON HOME- MAKERS THOSE WHO HAVE LITTLE EX- PERIENCE IN HOME SEWING AND WHO FIND IT ECONOMICAL TO MAKE MUCH OF THE FAMILY'S CLOTHING. THE MORE EXPERIENCED WHO DESIRE A READY REF- ERENCE ON HOME SEWING. THOSE FAM- ILIES WHO AT THIS TIME ARE UNDER THE NECESSITY OF RECEIVING CLOTH- ING FROM THEIR FEDERAL AND STATE GOVERNMENT. 41, IT IS HOPED THAT THE DIRECTIONS MAY BE FOUND HELP- FUL IN THE PROGRAM OF SELF-HELP AND HOME-MADE LIVING IN WHICH A LARGE PROPORTION OF THESE CITIZENS DESIRE TO PARTICIPATE. Oregon State Agricultural College Extension Service Corvallis, Oregon Cooperative Extension Work in Agriculture and Home Economics Paul V. Maria, Director Oregon State Agricultural College and United States Department of Agriculture, Cooperating Printed and distributed in furtherance of the Acts of Congress of May 8 and June dO, 1914 TABLE OP CONTENTS Page Sewing Equipment and Technique 3 Sewing Machine 3 Other Equipment 4 Pressing Equipment 6 Seams and Seam Finishes 7 Plain Seams and Finishes 7 Special Seams 8 Hems and Hemstitches 10 Stitches Used in Hems 10 Hems and Hem Finishes 11 Mitered Corners 14 Fabric Buttonholes 15 Pockets 18 Plackets 22 Bindings, Pipings, and Folds 24 Preparation of Bias 25 Bindings 25 Pipings 26 French Fold 26 Plaits 27 Fastenings 27 Garment Repair 29 Darning 29 Patching 30 Index 32 A Manual for Home Sewing By AZALEA SAGER Extension Specialist in Clothing and Textiles and satisfaction are the two chief reasons for making or ECONOMYremodeling garments at home.
    [Show full text]
  • Instructions and Free Patterns
    Instructions and free patterns www.mybernette.com “Romantic style” project sewing instructions Frilly blouse Sizes 3434––––4242 European (4(4(4-(4 ---1212 US/6US/6----1414 UK) You'll need - 1.2m (1 3/8 yd) pink taffeta (fabric width 1.5m (5')) - 0.45m (½ yd) white tulle (fabric width 1.5m (5')) - 0.50 m (1/2 yd) pink voile (fabric width 1.5m (5')) - 1.5m (1 2/3 yd) satin ribbon, approx. 4mm (1/6") wide - Assorted sewing and embroidery threads in pink - Embroidery stabilizer for the facing - Spray adhesive - Sewing thread to match the color of the fabric - Gathering foot - Cording foot Fabric rerecommendationcommendation Taffeta or other shiny, slightly crisp fabric for the blouse. Sheer fabrics that can be gathered with the gathering foot for the frills. Good to know The decorative stitches will cause the fabric to shrink slightly, so be sure to add 2.5cm (1") seam allowance to the outer facing when cutting it out. After embellishing the facing with decorative stitching, reposition the paper pattern on the stitched fabric and trim the seam allowance to 1.5cm (5/8"). Cutting out Seam allowanceallowancess ––– When cutting out, add 1.5cm (5/8") seam allowance to all edges and the hem, and 1cm (3/8") to armhole curves. Pink taffeta 2 x front 1 x back to fabric fold 2 x facing 2 x belt loops: 1.5cm x 8cm (5/8" x 3 ¼"), including seam allowance 1 x belt: 8cm x 66cm (3 ¼" x 26"), including seam allowance 2 x bias binding for armhole, cut on cross-grain: 4cm x 47cm (1 5/8" x 18 1/2") Sheer voile, taffetataffeta,,,, or tulle Tear or cut (depending on the fabric's texture) 2cm- (7/8"-) wide strips for the frill on the facing.
    [Show full text]