Trail Project and Equipment Checklist

Project: Trail Layout, Flagging and Trail Work Log Development

Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand Level sighting linear grades ea. used when one person is too short to sight on or organic layers are too deep to obtain accurate ground Sighting Rod elevation ea. Altimeter identify elevation of control points ea. Compass identify directions and locating position on landform ea. Topographic Map identify landform topographic features and elevations ea. Lidar Map identify landform topographic features and elevations ea. Shalstab Map identify slope stability ea. Aerial Photos identify landform geomorphic features ea. identify location on the landform and approximate elevation, provide topographic and GIS data maps, and plot control points, trail corridors and trail Hand Held GPS Unit alignments ea. 25 Foot Tape Measure measuring dimensions of prescribed trail structures ea.

100 Foot Cloth Tape Measure measuring length of prescribed trail bridges ea. Range Finder measuring length of prescribed trail bridges ea. Flagging identifying trail alignment rolls identifying trail alignment and marking trail features bundles Wire Flagging and structures 100 ea. bundles Wiskas identifying trail alignment 25 ea. 50 lb. 40D Nails staking wiskas into the ground box tree marking paint identifying trail alignment in rocky areas can measuring length and location of prescribed trail Rolotape Wheel features and structures (trail work log) ea. Clip Board storage for trail work log forms and writing surface ea. write in the rain forms to record trail construction Work Log Forms prescriptions ea. used to write trail work log footage (station) and Felt Tip Marker construction prescription on wire flags ea. Used to record trail work log footage and prescriptions Data Logger in electronic format ea. Project: Best Management Practices (BMPs)

Tool/Equipment Function/Use No. Unit

Metal T Post 6' used to support silt fencing ea. used to drive T post used with silt fencing into the Fence Post Driver ground ea. used to cut non woven fabric to length and cut holes Utility Knife for wire ties ea.

used to tie 9 gauge wire, fencing and non woven fabric Fence Pliers together around fence post and tie rebar together ea.

Wire Fencing, 9 Gauge, 3' High used to support non woven geotextile in silt fence With 4" Square Openings application lin. ft. Non Woven Geotextile Fabric used to construct silt fences lin. ft.

Staple Gun Manual 1/2" used to fasten geotextile fabric to wood stakes ea. used with staple gun to fasten geotextile fabric to Staples 1/2" wood stakes box Zip Ties, Black 5" Weather Resistant 25 lb. Test used to fasten geotextile fabric to T post pack used to hold sterile straw bales when carrying and Hay Hooks placing bales ea. Sandbags Heavy Duty With Tie used to dam and divert stream flow when installing String, 14.5" x 26" culverts ea.

Flexible Plastic Pipe, Dia. Sized According To Stream used with sand bags to divert stream flow when Flow installing culverts ea.

Drop Cloth, Non Woven secured under bridge to catch fasteners, and Geotextile Fabric debris falling from bridge lin. ft.

to attach under stringer to push the fabric out to catch 2" x 4" x 10' Wood Board materials and help to weight things down ea.

Twine used to tie drop cloth to bridge roll

Rebar Staples used to secure ends of drop cloth into ground ea. Straw Wattles 9" x 25' used to contain sediment at project site ea. Wood Stakes 18" used to pin straw wattles to ground ea. Straw Wattles 12" x 25' used to contain sediment at project site ea. Wood Stakes 24" used to pin straw wattles to ground ea.

used to drive wood stakes into straw wattles and rebar Hand Sledge 4lb. staples (used to secure fabric drop cloth) into ground ea.

Scaffolding Frame, Aluminum, used to provide temporary crossing and working Ladder Style, 5' High x 5' Wide platform to protect stream banks and channel unit 7' 10" x 19" Aluminum Scaffold used with scaffolding frame to provide a walking Planks surface and working platform for trail workers ea. used to provide temporary crossing to protect stream banks and channel (See Bridge Structure Pipe Bridge Construction Pipe Bridge ) Project: Trail Tread Construction & Maintenance

Clearing and Brushing (Includes All Trail Structure Sites) Tool/Equipment Function/Use No. Unit used to carry tools to worksite and transport fuel and Wheelbarrow bar oil containers ea. used to carry tools to worksite and transport fuel and Toter 1,500 lb. Capacity bar oil containers ea. used to carry tools to worksite and transport fuel and Toter 2,500 lb. Capacity bar oil containers ea. used to carry tools to worksite and transport fuel and Toter 3,500 lb. Capacity bar oil containers ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. fell standing trees and buck down trees within the With 16" Bar clearng limits ea. fell standing trees and buck down trees within the Chainsaw With 24" Bar clearng limits ea. fell standing trees and buck down trees within the Chainsaw With 36" Bar clearng limits ea. fell standing trees and buck down trees within the Chainsaw With 48" Bar clearng limits ea. fell standing trees and buck down trees within the Chainsaw With 60" Bar clearng limits ea. fell standing trees and buck down trees within the Chainsaw With 72" Bar clearng limits ea.

Chainsaw Power Pruner limbing tree branches in trail clearing limits ea. cover over chainsaw bar to facilitate carrying the Bar Covers (scabbard) chainsaw safely ea. chainsaw tools, file guides, files, file handles, drop Chainsaw Box center depth gauge, extra saw , grease gun ea. hardened carbide saw chain used when sawing through down trees or stumps with soil and small Carbide Saw Chain aggregate ea. Dolmar saw gas and bar oil container ea. High Impacting Plastic Wedges wedges used to fell trees and keep saw kerf open 8" while bucking ea. High Impacting Plastic Wedges wedges used to fell trees and keep saw kerf open 10 1/2" while bucking ea. High Impacting Plastic Wedges wedges used to fell trees and keep saw kerf open 12" while bucking ea. used to drive plastic wedges, remove undercut and Felling 5lb. chop through partially sawn down trees ea. fell standing trees and buck down trees within the Single 3' 6" clearng limits ea. fell standing trees and buck down trees within the Crosscut Saw Double 5' 6" clearng limits ea. fell standing trees and buck down trees within the Crosscut Saw Double 7' clearng limits ea. fell standing trees and buck down trees within the Crosscut Saw Double 8' clearng limits ea. fire hose cover over saw teeth to facilitate carrying the Bar Covers (scabbard) crosscut saw safely ea. setting hammer, setting stake, spider set gauge, combination jointer/raker gauge and crosscut Crosscut Saw Box sharpener/jointing file ea.

Lubricant Spray Bottle spray bottle with diesel oil to lubricate crosscut saw ea. Cobra Combi Gas Powered used to drill holes in rocks for the purpose of splitting Rock Drill and Breaker rock ea. Drill Steel With Threaded used to drill holes in rocks for the purpose of splitting Carbide Bits 1 1/4" x 12" rock ea. Drill Steel With Threaded used to drill holes in rocks for the purpose of splitting Carbide Bits 1 1/4" x 24" rock ea. Drill Steel With Threaded used to drill holes in rocks for the purpose of splitting Carbide Bits 1 1/4" x 36" rock ea. Drill Steel With Threaded used to drill holes in rocks for the purpose of splitting Carbide Bits 1 1/4" x 48" rock ea. Drill Steel With Threaded used to drill holes in rocks for the purpose of splitting Carbide Bits 1 1/4" x 60" rock ea. Rechargeable Aerosol Spray used to blow rock dust out drill holes before gluing Can 200 PSI stainless steel rod ea. chemical expansion agent used in vertical drill holes to Betonamit Type R fracture and break rock box chemical expansion agent used in horizontal drill holes Betonamit Type S to fracture and break rock box non explosive cartridges placed in drill holes filled with Magnum Boulder Buster water that fracture and break rock ea. Magnum Boulder Buster Cartridge #10 used on smaller size rocks ea. Magnum Boulder Buster Cartridge #20 used on medium size rocks ea. Magnum Boulder Buster Cartridge #30 used on larger size rocks ea. Cobra Pro Gas Powered Breaker used to break rock and excavate rock and hard soil ea. used with breaker to break apart exposed fractured Moil Point Breaker Bit 18" rock surfaces ea. used with breaker to fracture exposed rock surfaces Narrow Chisel Breaker Bit 18" and remove rock projecting above grade ea. used with breaker to break apart and excavate highly Digging Chisel Breaker Bit 18" fractured rock and rocky soils ea. used with breaker to break apart and excavate hard Clay Spade Breaker Bit 14" clay soils ea.

Dolmar breaker gas/two cycle oil mix container ea.

Breaker Tool Kit wrenches and screwdrivers to tune and repair ea.

used to brush the trail within the clearing limits, light to Powered Brushcutters 36-46cc medium brush with maximum 1/2" diameter stems ea.

used to brush the trail within the clearing limits, Powered Brushcutters 47-57cc medium brush with maximum 3/4" diameter stems ea. Dolmar brushcutter gas/two cycle oil mix container ea. used to protect operator's face and neck from flying Hard Hat With Face Shield woody debris ea. brushcutter tools, shear pins, mill bastard files, file Brushcutters Tool Box handles, grease gun, extra saw ea. Swedish Brush Axe used for cutting light to medium brush ea. Brush used for cutting heavy brush ea. used to protect shin and foot when using brush hook Shin-Instep Guard and Swedish brush axe ea.

leg protection while using , crosscut , Chainsaw Chaps brushcutters, brush hooks and Swedish brush ea. Grass Whip used to cut grass and small succulent plants ea.

Bow Saw used to cut larger brush and buck small downed trees ea. used to prune small limbs encroaching in the trail Loppers clearing limits ea. used to perform face cut when felling trees, chop Single -Bit Axe through downed trees and drive plastic wedges ea. used to perform face cut when felling trees and chop Double-Bit Axe through downed trees ea. Pole Saws, Telescoping limbing tree branches in trail clearing limits ea. Rigging Equipment For Trail See Rigging Operations (Direct Pulls and Choker Rolls Clearing Used in Clearing) Peavy used to roll and rotate logs out of the trail alignment ea. used to roll and rotate logs out of the trail alignment ea. used to lift, carry or rotate logs out of the trail Timber Carrier AKA Log Tongs alignment ea. used to dig out, roll or lever rocks off the trail Pinch Point Crow Bar 60" alignment ea. Peeler Bar 6' used to roll or lever logs off the trail alignment ea. used to dig out and remove tree stobs/roots ea. Cutter used to dig out and remove tree stobs/roots ea. Pick Mattock used to dig out and remove tree stobs/roots ea.

Round Point Shovel used to dig out and remove rocks and tree stobs/roots ea. used to rake small limbs and organics off the trail McLeod alignment ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to rake small limbs and organics off the trail Bow Rake alignment ea. used to toss small limbs and organics off the trail Pitch Fork alignment ea. Native Material Fabrication Tool/Equipment Function/Use No. Unit used to peel bark off of downed logs and pry open Peeler Bar 6' logs being split apart ea. used to peel bark off of downed logs and pry open Bark Spud logs being split apart ea. used to mark the line across the end of the log the Checker Wedge wedges will be driven in to split the log apart ea.

Redwood Splitting Wedge 8 lb. driven into the end of the log to spit it apart ea.

Redwood Splitting Wedge 6 lb. driven into the end of the log to spit it apart ea. Double Jack 8 lb. used to drive splitting wedges into the log ea. Slick used to remove splinters and shape split lumber ea. Drawknife used to remove splinters and shape split lumber ea. used to carry tools to worksite and transport fuel and Wheelbarrow bar oil containers ea. used to carry tools to worksite and transport fuel and Toter 1,500 lb. Capacity bar oil containers ea. used to carry tools to worksite and transport fuel and Toter 2,500 lb. Capacity bar oil containers ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea.

used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Can gas container for toters ea. Log Wizard Chainsaw Attachment used to remove bark and plane/shape split lumber ea. Alaskan Saw Mill With 7 cu. in. Powerhead Min. used to mill lumber from downed logs ea. Ripping Chain, 3/8" Pitch used with chainsaw to rip boards from logs ea. Mini Mill With 5 cu.in. Powerhead Min used to trim edges of sawn boards into desired widths ea.

Dolmar chainsaw gas/two cycle oil mix and bar oil container ea. Cobra Combi Gas Powered used to drill holes in rocks for the purpose of splitting Rock Drill and Breaker and shaping rock ea. Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. Dolmar breaker gas/two cycle oil mix container ea. Drill Steel With Threaded used with gas powered drill to drill holes in rocks for Carbide Bits 1 1/4" x 12" the purpose of splitting and shaping rock ea. Drill Steel With Threaded used with gas powered drill to drill holes in rocks for Carbide Bits 1 1/4" x 24" the purpose of splitting and shaping rock ea. Drill Steel With Threaded used with gas powered drill to drill holes in rocks for Carbide Bits 1 1/4" x 36" the purpose of splitting and shaping rock ea. Drill Steel With Threaded used with gas powered drill to drill holes in rocks for Carbide Bits 1 1/4" x 48" the purpose of splitting and shaping rock ea. Drill Steel With Threaded used with gas powered drill to drill holes in rocks for Carbide Bits 1 1/4" x 60" the purpose of splitting and shaping rock ea. Feathers and Wedges 1 1/4" x 8" steel wedges drive in drill holes to split rocks set

Bosche Rotary Hammer used to drill holes in rocks for plugs and feathers ea.

Generator 2,500 Watt used to power bosch rotary hammer ea. used with rotary hammer to drill holes in rocks for the SDS Max 1/2" Bit purpose of splitting and shaping rock ea. used with rotary hammer to drill holes in rocks for the SDS Max 1 1/4" Bit purpose of splitting and shaping rock ea.

Feathers and Wedges 1/2" x 4" steel wedges drive in drill holes to split rocks set used to drive steel wedges and strike slab and rifting Striking Hammer 8lb. hammers ea. Slab Hammer used to split and shape rock ea. Rifting Hammer used to split and shape rock ea. Trail Tread Excavation Tool/Equipment Function/Use No. Unit used to rake organics off the trail alignment, cast McLeod excavated soil off the trail and shape the trail tread ea.

Pick Mattock used to excavate rocky or consolidated soils ea.

Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils, cast excavated soil off Hazel the trail and shape the trail tread ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils and cast excavated soil Round Point Shovel off the trail ea. used to dig out smaller rocks protruding into the trail Pinch Point Crow Bar 60" tread ea. Tamper 10" x10", 15 lb. used to compact trail tread ea. used to break or smash rocks protruding into the trail Double Jack 10 lb. tread ea. used to break soft rock and excavate soft rock and Slide Hammer hard soil ea. used with slide hammer to break apart exposed Moil Point Breaker Bit 12" fractured rock surfaces ea. used with slide hammer to fracture exposed rock Narrow Chisel Breaker Bit 12" surfaces and remove rock projecting above grade ea. used with slide hammer to break apart and excavate Digging Chisel Breaker Bit 12" highly fractured rock and rocky soils ea. Cobra Pro Gas Powered Breaker used to break rock and excavate rock and hard soil ea. used with breaker to break apart exposed fractured Moil Point Breaker Bit 18" rock surfaces ea. used with breaker to fracture exposed rock surfaces Narrow Chisel Breaker Bit 18" and remove rock projecting above grade ea. used with breaker to break apart and excavate highly Digging Chisel Breaker Bit 18" fractured rock and rocky soils ea. used with breaker to break apart and excavate hard Clay Spade Breaker Bit 14" clay soils ea. Dolmar breaker gas/two cycle oil mix container ea. Breaker Tool Kit wrenches and screwdrivers to tune and repair ea. Dozer (SWECO) 48" Max. used to excavate trail tread, lay back cutbank, remove Width outside berm and outslope trail tread ea.

Dozer Slope Board Attachment used to lay back cutbank and cut off berm. ea. Dozer Hydraulic Winch used to pull down trees out of trail alignment and Attachment extricate dozer when stuck ea. Dozer Air Compressor and used to operate assorted air tools and blow dust off Hose Attachment dozer engine and air filters ea. Dozer Hydraulic Hammer Attachment used to break rock and drive in post ea. cutbank, remove outside berm, outslope trail tread, excavate drainage crossings and load wheelbarrows Mini Excavator, 4' overall width and toters ea. Excavator Hydraulic Thumb used to grasp and place brush, organics, logs and Attachment rocks when excavating trail alignment ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea.

used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Cans For Dozer and Excavator diesel fuel to operate dozer and excavator ea. used to carry tools and materials to worksite, export soil away from drainages, or transport soil being used Wheelbarrow for fill material ea. used to carry tools and materials to worksite, transport dozer and mini excavator attachments and fuel cans, export soil away from drainages and transport soil Toter 1,500 lb. Capacity being used for fill material ea. used to carry tools and materials to worksite, transport dozer and mini excavator attachments and fuel cans, export soil away from drainages and transport soil Toter 2,500 lb. Capacity being used for fill material ea. used to carry tools and materials to worksite, transport dozer and mini excavator attachments and fuel cans, export soil away from drainages and transport soil Toter 3,500 lb. Capacity being used for fill material ea. 5 Gallon Fuel Can gas container for toters ea. Viberplate Compactor 180 lb. used to compact trail tread ea. Tool Box With Assorted used to perform minor adjustments, maintenance and Wrenches, Sockets, Screw repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. Dolmar gas container for viberplate compactor ea. Clinometer or Abney Hand used to monitor and verify final linear grade meets Level design standard ea. used to monitor and verify final cross slope meets Smart Level design standard ea. Trail Hardening Aggregate Tool/Equipment Function/Use No. Unit used to cover aggregate pile to prevent erosion, Plastic Tarp raveling and segregation due to rain water ea.

used to load aggregate and soil into wheelbarrows or Round Point Shovel toters and spread aggregate once dumped on the trail ea.

used to load aggregate and soil into wheelbarrows or Square Point Shovel toters and spread aggregate once dumped on the trail ea. Small Tractor With Front End used to load aggregate and soil into wheelbarrows or Loader toters ea.

Wheelbarrow used to transport aggregate and soil out trail ea. Toter 1,500 lb. Capacity used to transport aggregate and soil out trail ea.

Toter 2,500 lb. Capacity used to transport aggregate and soil out trail ea.

Toter 3,500 lb. Capacity used to transport aggregate and soil out trail ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea.

used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Can gas container for toters ea. used to perform initial spreading of aggregate and soil McLeod dumped on trail. ea. used to perform initial spreading of aggregate and soil Bow Rake dumped on trail. ea. used to perform final shaping of aggregate and soil to Asphalt Lute designed grade and cross slope ea. ATV With Water Tank and used to water aggregate and soil to achieve proper Spray Bar compaction ea.

Water Tank 1,500 Gal. Min. storage for water used to dampen aggregate and soil ea.

Gas Powered Water Pump used to pressurize water through fire hose ea. 1" Fire Hose used to transport water from storage tank to trail feet Spray Nozzle used to dampen aggregate and soil ea. Tamper 10" x10", 15 lb. used to compact loose soils in foundation ea. Viberplate Compactor 180 lb. used to compact trail tread ea. Roller Smooth Double Drum 38" width used to compact trail tread ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea.

used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. Dolmar gas container for viberplate compactor and roller ea. Clinometer or Abney Hand used to monitor and verify final linear grade meets Level design standard ea. used to monitor and verify final cross slope meets Smart Level design standard ea. Trail Hardening, Stone Pitching and Rip Rap

Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for stone pitching and rip Level rap structures ea. used to rake organics off the structure footprint and McLeod shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea.

used to excavate loamy soils and cast excavated soil Round Point Shovel off the foundation or load into wheel barrow or toter ea. used to cast excavated soil off the foundation or load Square Point Shovel into wheel barrow or toter ea. used to dig out smaller rocks protruding into the foundation, move larger rocks into position and lever Pinch Point Crow Bar 60" rocks together ea.

Tamper 10" x10", 15 lb. used to compact loose soils in foundation ea. used to break or smash rocks protruding into the Double Jack 10 lb. foundation ea. used to break potruding pieces of rock off for better contacts, used to breakdown and compress rock Single Jack 4lb. backfill called crush ea.

Bosche Rotary Hammer used to drill holes in rocks for plugs and feathers ea.

Generator 2,500 Watt used to power bosch rotary hammer ea. used with rotary hammer to drill holes in rocks for the SDS Max 1/2" Bit purpose of splitting and shaping rock ea.

Feathers and Wedges 1/2" x 4" used to split rock using smaller holes more frequently set used to excavate foundation, load wheelbarrows and Mini Excavator, 4' overall width toters and place rocks ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation and place rocks ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. used to carry stones to worksite or to location where Rock Litter they are placed in the structure. ea. used to carry tools and stones to worksite or transport Wheelbarrow soil being used for fill material elsewhere ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 1,500 lb. Capacity elsewhere ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 2,500 lb. Capacity elsewhere ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 3,500 lb. Capacity elsewhere ea. 5 Gallon Fuel Can gas container for toters ea.

Rigging Equipment For Stone See Rigging Operations (Highleads and Skylines, Pitching and Rip Rap Transverse Anchors and Highleads off of Skylines used to measure stones for sorting, breaking and Tape Measure 25' shaping and monitoring the rise of a rip rap course ea.

Chalk used to mark stones for sorting, breaking and shaping ea. Striking Hammer 8lb. used to strike slab and rifting hammers ea. Slab Hammer 8lb. used to split and shape rock ea. Rifting Hammer 8lb. used to split and shape rock ea. Cutter's Hammer used to strike steel rock shaping tools ea.

Hand Tracer Carbide 11/8"x3" used to score line on stone where it is to be broken ea. Hand Point Carbide 1" used to take off high points on stone ea. used to take off high points on stone, remove small Hand Chisel Carbide 1" ledges or score lines ea. used to remove material parallel to a flat stone or to Hand Set Carbide 11/8" x 3" remove drill marks ea.

Drift Pin Straight 1/4" Point used to set small rocks in the gaps between rocks ea.

Drift Pin Straight 3/8" Point used to set small rocks in the gaps between rocks ea. Hammer Point Carbide 3lb. used to remove high points and shape stone ea. Spalling Hammer 4lb. used to break and shape rock ea. Cross Pien Hammer used to break and shape rock ea.

Mason (Mash) Hammer 6lb. used to break and crush rock for gaps between rocks ea. Road to Trail Conversion Tool/Equipment Function/Use No. Unit used on roads 12' or less wide to scarify road bench, cut and push outside of road bench into cutbank, Dozer 18,000 to 22,000 lbs. compact soil placed against cutbank, excavate max. 7' Track Width (2.9 cy drainage crossings and push crossing material to capacity) storage locations outside of crossing ea. used on roads 13'-18' wide to scarify road bench, cut and push outside of road bench into cutbank, compact Dozer 40,000 to 55,000 lbs. soil placed against cutbank, excavate drainage max. 9.5' Track Width (8 cy crossings and push crossing material to storage blade capacity) locations outside of crossing ea. used on roads 19'-24' wide to scarify road bench, cut and push outside of road bench into cutbank, compact Dozer 77,000 to 85,000 lbs. soil placed against cutbank, excavate drainage max. 9.5' Track Width (11 cy crossings and push crossing material to storage blade capacity) locations outside of crossing ea. used on roads 25'-30' wide to scarify road bench, cut and push outside of road bench into cutbank, compact Dozer 95,000 to 105,000 lbs. soil placed against cutbank, excavate drainage max. 10' Track Width (15 cy crossings and push crossing material to storage blade capacity) locations outside of crossing ea.

used on roads 12' or less wide to brush road prism, scarify cutbank, excavate fill material and place it against cutbank, compact soil placed against cutbank, Excavator 26,000 to 36,000 excavate drainage crossings and establish original lbs. max. 11.5' Total Swing channel morphology and place brush onto cutbank, Width (.7 cy bucket capacity) embankment and crossing slopes ea.

used on roads 13'-18' wide to brush road prism, scarify cutbank, excavate fill material and place it against cutbank, compact soil placed against cutbank, Excavator 50,000 to 70,000 excavate drainage crossings and establish original lbs. max. 15' Total Swing Width channel morphology and place brush onto cutbank, (2 cy bucket capacity) embankment and crossing slopes ea.

used on roads 19'-24' wide to brush road prism, scarify cutbank, excavate fill material and place it against cutbank, compact soil placed against cutbank, Excavator 81,000 to 110,000 excavate drainage crossings and establish original lbs. max. 18.5' Total Swing channel morphology and place brush onto cutbank, Width (4 cy bucket capacity) embankment and crossing slopes ea.

used on roads 25'-30' wide to brush road prism, scarify cutbank, excavate fill material and place it against cutbank, compact soil placed against cutbank, Excavator 155,000 to 190,000 excavate drainage crossings and establish original lbs. max. 20.5' Total Swing channel morphology and place brush onto cutbank, Width (6.6 cy bucket capacity) embankment and crossing slopes ea.

used to clean up deisel, oil , hydraulic oil spills realted Universal Bag Spill Kit, 20 Gal. to dozer and excavator operations ea. used to end haul crossing material to designated Dump Truck (ten cy capacity) storage location ea. Articulated Dump Truck (30 cy used to end haul crossing material to designated capacity) storage location ea. Loader Wheeled 45,000 to 65,000 lbs. (6 cy bucket capacity) used to load crossing material into dump trucks ea. Dozer (SWECO) 48" Max. used to scape loose soil off of trail bench, outslope Width trail bench and remove berm

Dozer Slope Board Attachment used to cut off berm. ea. McLeod used to shape the trail tread Hazel Hoe used to shape the trail tread File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools Wheelbarrow used to carry tools, fuel and materials to worksite ea. 5 Gallon Fuel Cans For Dozer and Excavator diesel fuel to operate dozer and excavator ea. used to carry tools and materials to worksite and Toter 1,500 lb. Capacity transport dozer attachments and fuel cans ea. used to carry tools and materials to worksite and Toter 2,500 lb. Capacity transport dozer attachments and fuel cans ea. used to carry diesel fuel cans for , heavy equipment servicing and repair tools and Toter 3,500 lb. Capacity SWECO attachments ea.

Tool Box For Excavator, Toters tools for servicing and repairing excavator/toters and and Other Power Equipment installing attachments ea. 5 Gallon Fuel Can gas container for toters ea. Roller Smooth Double Drum 38" width used to compact trail tread ea.

Viberplate Compactor 180 lb. used to compact trail tread ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea.

used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. Dolmar gas container for viberplate compactor and roller ea. Clinometer or Abney Hand used to monitor and verify final linear grade meets Level design standard ea. used to monitor and verify final cross slope meets Smart Level design standard ea. Project: Retaining Structure Construction

Single Tier Log Retaining Walls Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for single tier log retaining Level walls ea.

used with clinometer or abney hand level to layout 25' Tape Measure foundations for single tier log retaining walls ea. used for laying out retaining wall location and finished Form Stakes 5' elevations ea.

String Line used with form stakes for laying out retaining walls roll Chainsaw With 24" Bar buck down logs used for retaining wall ea. Chainsaw With 36" Bar buck down logs used for retaining wall ea. Chainsaw With 48" Bar buck down logs used for retaining wall ea. cover over chainsaw bar to facilitate carrying the Bar Covers (scabbard) chainsaw safely ea.

chainsaw tools, file guides, files, file handles, drop Chainsaw Saw Box center depth gauge, extra saw chain, grease gun ea. hardened carbide saw chain used when sawing through down trees or stumps with soil and small Carbide Saw Chain aggregate ea. Saw Chaps used to protect sawyers legs ea. Dolmar saw gas and bar oil container ea. High Impacting Plastic Wedges 8" wedges used to keep saw kerf open while bucking ea. High Impacting Plastic Wedges 10 1/2" wedges used to keep saw kerf open while bucking ea. Felling Axe 5lb. used to drive plastic wedges into saw kerf ea. Crosscut Saw Single 3' 6" buck down logs used for retaining wall ea. Crosscut Saw Double 5' 6" buck down logs used for retaining wall ea. Crosscut Saw Double 7' buck down logs used for retaining wall ea. fire hose cover over saw teeth to facilitate carrying the Bar Covers (scabbard) crosscut saw safely ea. setting hammer, setting stake, spider set gauge, combination jointer/raker gauge and crosscut Crosscut Saw Box sharpener/jointing file ea.

Lubricant Spray Bottle spray bottle with diesel oil to lubricate crosscut saw ea. Cutter Mattock used to excavate footing and remove roots ea. Pick Mattock used to excavate footing and remove small rocks ea. Pulaski used to excavate footing and remove roots ea. Round Point Shovel used to excavate footing and shape footing to log ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate footing and place smaller logs in Mini Excavator, 4' overall width footing ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation and place logs ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea.

used to carry tools, fuel and materials to worksite and Wheelbarrow transport footing soil to sites needing fill material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil being used for fill material in Toter 1,500 lb. Capacity structures ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil being used for fill material in Toter 2,500 lb. Capacity structures ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil being used for fill material in Toter 3,500 lb. Capacity structures ea. 5 Gallon Fuel Can gas container for toters ea. Rigging Equipment For See Rigging Operations (Highleads and Skylines, Retaining Wall Construction Transverse Anchors and Highleads off of Skylines Peavy used to roll and rotate logs into footing ea. Cant Hook used to roll and rotate logs into footing ea. Timber Carrier used to lift, carry or rotate logs into footing ea. Pinch Point Crow Bar 60" used to roll or lever logs into footing ea. Peeler Bar 6' used to roll or lever logs into footing ea. Gas Powered Drill used to drill hole through log ea. Auger Drill Bit 9/16" Dia. used to drill hole through log ea. Double Jack 10 lb. used to drive 5/8" rebar through log ea.

Viberplate Compactor 180 lb. used to compact trail tread behind wall ea. Single and Multi Tier Rock Retaining Walls (dry stone and wet masonry)

Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand Level used to layout foundations for rock retaining walls ea. used with clinometer or abney hand level to layout 25' Tape Measure foundations for rock retaining walls ea. used with clinometer or abney hand level to layout 100' Tape Measure foundations for rock retaining walls ea. Form Stakes used to anchor sting line ea. used to turn form stakes to line up the holes in the 12" Aluminum Pipe Wrench stakes ea. used to designate finished height of wall course and String Line as a guide to keep the courses level roll used to quality check final course of rock wall to 2' level ensure it is same height as stringline ea. used to rake organics off the structure footprint and McLeod shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea.

used to excavate loamy soils and cast excavated soil Round Point Shovel off the foundation or load into wheel barrow or toter ea. used to excavate and shape the bottom of the Square Point Shovel foundation or load soil into wheelbarrow or toter ea. used to dig out smaller rocks protruding into the foundation, move larger rocks into position and lever Pinch Point Crow Bar 60" rocks together ea. Tamper 10" x10", 15 lb. used to compact loose soils in foundation ea. used to drive form stakes into ground, break or smash rocks protruding into the foundation and making crush Double Jack 10 lb. fill ea. Used to break potruding pieces of rock off for better contacts, used to breakdown and compress rock Single Jack 4lb. backfill called crush ea. Bosche Rotary Hammer used to drill holes in rocks for plugs and feathers ea. Generator 2,500 Watt used to power bosch rotary hammer ea. used with rotary hammer to drill holes in rocks for the SDS Max 1/2" Bit purpose of splitting and shaping rock ea.

Feathers and Wedges 1/2" x 4" used to split rock using smaller holes more frequently set used to excavate retaining structure foundation, load Mini Excavator, 4' overall width wheelbarrows and toters and place rocks ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation and place wall rocks ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. used to carry stones and crush fill to worksite or to Rock Litter location where they are placed in the structure. ea.

used to carry tools, stones and crush fill to worksite or Wheelbarrow transport soil being used for fill material elsewhere ea.

used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 1,500 lb. Capacity transport soil being used for fill material and crush fill ea.

used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 2,500 lb. Capacity transport soil being used for fill material and crush fill ea.

used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 3,500 lb. Capacity transport soil being used for fill material and crush fill ea. 5 Gallon Fuel Can gas container for toters ea. See Rigging Operations (Highleads and Skylines, Rigging Transverse Anchors and Highleads off of Skylines used to measure stones for sorting, breaking and Tape Measure 25' shaping ea.

Chalk used to mark stones for sorting, breaking and shaping ea. Striking Hammer 8lb. used to strike slab and rifting hammers ea. Slab Hammer 8lb. used to split and shape rock ea. Rifting Hammer 8lb. used to split and shape rock ea. Cutter's Hammer used to strike steel rock shaping tools ea.

Hand Tracer Carbide 11/8"x3" used to score stone where it is to be broken ea. Hand Point Carbide 1" used to take off high points on stone ea. used to take off high points on stone, remove small Hand Chisel Carbide 1" ledges or score lines ea. used to remove material parallel to a flat stone or to Hand Set Carbide 11/8" x 3" remove drill marks ea. Hammer Point Carbide 3lb. used to remove high points and shape stone ea. Spalling Hammer 4lb. used to break and shape rock ea. Cross Pien Hammer used to break and shape rock ea. Mason (Mash) Hammer 6lb. used to break and crush rock for fill ea. used to maneuver and position rocks once placed on Crowbar 18" the wall ea. Wire Brush used to clean rocks of dirt and organics ea. Masonry Sponge used to clean rocks ea. Grout Sponge used to wet rocks before applying mortar ea. Mortar Mixing Tub container used to mix mortar and water ea. Mortar Mixing Hoe tool used to mix mortar and water ea. used to supply water to mixing tub and sponge used to Water Bucket 5 Gal. clean and wet rocks ea. Brick Trowel used to apply, level and shape mortar to rocks ea. Pointing Trowel used to apply, level and shape mortar to rocks ea. used to apply, level and shape mortar to rocks in Margin Trowel narrow hard to reach areas ea. used to apply and form/shape mortar between rocks Tuck Pointer on exposed faces ea. used to apply and form/shape mortar between rocks Brick Jointer on exposed faces ea. Roto Hammer, Gas Powered 1/2" used to drill 13/16" hole in rock for stainless steel rod ea.

13/16" x 24" Rock Drill Bit used to drill hole in rock for 3/4" stainless steel rod ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. Rechargeable Aerosol Spray used to blow rock dust out drill holes before gluing Can 200 PSI stainless steel rod ea. used to pin rock to the bottom course when on an Stainless Steel Rod 3/4" Dia. incline ea.

Hilti Glue Gun and Glue used to secure stainless steel rod and seal drill hole ea.

Portable Coring Machine used to drill hole in rock for 3/4" stainless steel rod ea. Viberplate Compactor 180 lb. used to compact trail tread behind wall ea.

used to monitor how level each course is and the Carpenter's Level 4' prescribed tilt back for the foundation and each course ea.

used to monitor how level each course is and the Smart Level prescribed tilt back for the foundation and each course ea. Multi-Tier Interlocking Retaining Structures (dimensioned lumber and log structures)

Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for interlocking retaining Level structure ea.

used with clinometer or abney hand level to layout 25' Tape Measure foundations for interlocking retaining structure ea. used with clinometer or abney hand level to layout 100' Tape Measure foundations for rock retaining walls ea. used to rake organics off the structure footprint and McLeod shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea.

used to excavate loamy soils and cast excavated soil off the foundation, load soil into wheel barrow or toter Round Point Shovel or shovel backfill material behind structure ea. used to excavated and shape the bottom of the foundation or load soil into wheel barrow or toter or Square Point Shovel shovel backfill material behind structure ea. used to dig out smaller rocks protruding into the Pinch Point Crow Bar 60" foundation ea. used to break or smash rocks protruding into the Double Jack 10 lb. foundation ea. Timber Carrier used to lift and place logs ea. Stringer Cart used to transport logs or lumber to structure site ea. Trail Cart used to transport logs or lumber to structure site ea. buck down logs used for retaining wall an power log Chainsaw With 24" Bar wizard attachment ea. cover over chainsaw bar to facilitate carrying the Bar Covers (scabbard) chainsaw safely ea.

chainsaw tools, file guides, files, file handles, drop Chainsaw Saw Box center depth gauge, extra saw chain, grease gun ea. hardened carbide saw chain used when sawing through down trees or stumps with soil and small Carbide Saw Chain aggregate ea. Dolmar saw gas and bar oil container ea. High Impacting Plastic Wedges 8" wedges used to keep saw kerf open while bucking ea. High Impacting Plastic Wedges 10 1/2" wedges used to keep saw kerf open while bucking ea. Felling Axe 5lb. used to drive plastic wedges into saw kerf ea. Crosscut Saw Single 3' 6" buck down logs used for retaining wall ea. Crosscut Saw Double 5' 6" buck down logs used for retaining wall ea. Crosscut Saw Double 7' buck down logs used for retaining wall ea. fire hose cover over saw teeth to facilitate carrying the Bar Covers (scabbard) crosscut saw safely ea. setting hammer, setting stake, spider set gauge, combination jointer/raker gauge and crosscut Crosscut Saw Box sharpener/jointing file ea.

Lubricant Spray Bottle spray bottle with diesel oil to lubricate crosscut saw ea.

Rigging Equipment For See Rigging Operations (Highleads and Skylines, Retaining Wall Construction Transverse Anchors and Highleads off of Skylines used to excavate retaining structure foundation, load Mini Excavator, 4' overall width wheelbarrows and toters and place logs ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation and place logs ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. Tamper 10" x10", 15 lb. used to compact loose soils in foundation ea. used to compact loose soils in foundation and trail Viberplate Compactor 180 lb. tread behind wall ea. Dolmar gas container for viberplate compactor ea. used to carry tools to worksite or transport soil being Wheelbarrow used for fill material elsewhere or crush fill ea.

used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 1,500 lb. Capacity transport soil being used for fill material and crush fill ea.

used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 2,500 lb. Capacity transport soil being used for fill material and crush fill ea.

used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 3,500 lb. Capacity transport soil being used for fill material and crush fill ea. 5 Gallon Fuel Can gas container for toters ea. used to layout notches on facers, wings and anchor Tape Measure 25' post ea. used to layout notches on facers, wings and anchor Framing Square post ea. used to layout notches on facers, wings and anchor Combination Square post ea. used to scribe the shape and depth of the notch on log Log Scribe interlocking structures Carpenter's Pencil used to scribe notch lines ea. used to support lumber while performing layout and Saw Horse notching ea. used to pin logs in position while scribing and notching Log Dog logs ea. Peavey used to roll and maneuver logs into position ea.

Cordless Circular Saw 7 1/4" used to cut out notches ea. Extra Battery Packs charged battery packs for circular saw ea. Circular Saw 7 1/4" Electric used to cut out notches ea. Circular Saw 7 1/4" Saw Blades extra saw blades ea. Generator 2,500 Watt used to power electric circular saw and drill ea. Power Cord 50' With GFI Water Proof Receptacle used to supply power to electric saw and drill ea. Chainsaw, With 12" Carving Bar used to cut out notches ea. chainsaw tools, file guides, files, file handles, drop Chainsaw Saw Box center depth gauge, extra saw chain, grease gun ea. Dolmar saw gas and bar oil container ea. cover over chainsaw bar to facilitate carrying the Bar Covers (scabbard) chainsaw safely ea. Chainsaw Chaps leg protection while using chainsaws ea. Handsaw Crosscut used to cut out notches ea. used to break out wood/plastic wood between saw Hand Axe cuts ea. used to break out wood/plastic wood between saw Wood Chisel 1" cuts and shape bottom of notches ea. used to break out wood/plastic wood between saw Wood Chisel 1 1/2" cuts and shape bottom of notches ea. used to break out wood/plastic wood between saw Wood Chisel 2" cuts and shape bottom of notches ea. Log Wizard Chainsaw Attachment used to plane/shape notches in logs ea. Slick 3 1/2" used to shape notches in logs ea. Inshave Draw Knife used to shape notches in logs ea. Gouge, Shallow Sweep, 2" used to perform final shaping of log notches ea. Wood Mallet used to strike gouge and chisels ea. Rasp, Surform Flat Bottom used to shape the bottom and sides of the notches ea. Rasp Blades replacement blades for surform rasp ea. used to monitor how level each course is and the Carpenter's Level 4' slope of the foundation and the anchor post ea. used to monitor how level each course is and the Smart Level slope of the foundation and the anchor post ea. used for drilling pilot nail holes in facers and anchor Cordless Drill 1/2" post ea. Extra Battery Packs charged battery packs for cordless drill ea. used to drill pilot holes for 60d nails used to pin lap Drill Bit 7/32" joints in facers ea. used to drill pilot holes for 12" spikes used to pin the Drill Bit 5/16" top anchor posts ea. used to drive nails and spikes into facers and anchor Hammer 20 oz. Rip Claw post ea. used to drive nails and spikes into facers and anchor Hand Sledge 2lb. post ea. Soldier Pile Retaining Structures Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for soldier pile retaining Level structure ea.

used with clinometer or abney hand level to layout 25' Tape Measure foundations for soldier pile retaining structure ea.

used with clinometer or abney hand level to layout 100' Tape Measure foundations for soldier pile retaining structure ea. used to layout foundations for soldier pile retaining Pin Flags structures bundle String Line used to establish finished height of retaining wall ea. used to rake organics off the structure footprint and McLeod shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils and cast excavated soil off the foundation, load soil into wheel barrow or toter Round Point Shovel or shovel backfill behind wall ea. used to compact loose soils in foundation and soil or Tamper 10" x10", 15 lb. aggregate placed behind wall ea. used to compact loose soils in foundation and soil or Viberplate Compactor 180 lb. aggregate placed behind wall ea. Dolmar gas container for viberplate compactor ea.

used to carry tools to worksite or transport soil being Wheelbarrow used for fill material elsewhere or crush fill behind wall ea. used to carry tools and materials to worksite, transport fuel cans, and transport soil or aggregate being used Toter 1,500 lb. Capacity for fill material behind wall ea. used to carry tools and materials to worksite, transport fuel cans, and transport soil or aggregate being used Toter 2,500 lb. Capacity for fill material behind wall ea. used to carry tools and materials to worksite, transport fuel cans, and transport soil or aggregate being used Toter 3,500 lb. Capacity for fill material behind wall ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Can gas container for toters ea. Cobra Combi Gas Powered used to drive in 1" rebar, H beam post and duckbill Rock Drill and Breaker anchors into earth and drill 1 1/8" hole in rock ea.

Hydraulic Hammer Drill 50lb. used to drive in 1" rebar, H beam post and duckbill With Hoses anchors into earth and drill 1 1/8" hole in rock ea.

Portable Hydraulic Power Unit used to power hydraulic hammer ea. Dolmar fuel for hydraulic power unit ea. used with gas or hydraulic drill breakers to drive 1" Rebar Driver Head rebar into earth ea. Post Driver, Manual used to drive 1" rebar into soft earth ea. used with gas or hydraulic drill breakers to drill 1 1/8" 1 1/8" x 12" Rock Drill Bit hole into rock ea. Hilti Glue Gun and Glue used to glue 1" rebar into rock ea. used with gas or hydraulic drill breakers to drive H H Beam Post Driving Head beam post into earth ea. Duckbill Ground Anchor, 3,000 lb. Holding Capacity used to anchor H beam post ea. Drive Gad 54" used to drive duckbill anchor into earth ea. High Lift Jack used to pull on duckbill anchor cable to set duckbill ea. Generator 2,500 Watt used to power roto hammer drill ea. Roto Hammer, Electric 1/2" used to drill 11/16" hole in rock for expansion bolt ea. 11/16" x 6" Rock Drill Bit used to drill hole in rock for 5/8" wedge anchor ea. Wedge Anchor 5/8" x 3' used to anchor all thread rod ea. Ratchet 3/8" Drive, Socket Set used to secure fasteners used to attach all thread to and Wrenches anchors and H beam post ea. Cordless Drill 1/2" used to drill holes in metal cap ea. Extra Battery Packs charged battery packs for cordless drill ea. 1/4" x 3" High Speed Steel Drill used with cordless drill to drill 1/4" hole through metal Bit cap ea. used to adapt 3/8" drive ratchet to 1/4" nut drive 1/4" x 3/8" Adaptor Socket sockets ea. used with ratchet to drive 1/4" cap screws through Nut Drive Socket Set metal cap and into H beam post ea. Geotextile Retaining Structures Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for geotextile retaining Level structure ea.

used with clinometer or abney hand level to layout 25' Tape Measure foundations for geotextile retaining structure ea.

used with clinometer or abney hand level to layout 100' Tape Measure foundations for geotextile retaining structure ea. used to layout foundations for geotextile retaining Pin Flags structures bundle used to rake organics off the structure footprint and McLeod shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils and cast excavated soil off the foundation, load soil into wheel barrow or toter Round Point Shovel or shovel backfill on fabric ea. used to excavated and shape the bottom of the foundation or load soil into wheel barrow or toter or Square Point Shovel shovel backfill material on fabric ea. used to dig out smaller rocks protruding into the Pinch Point Crow Bar 60" foundation ea. used to break or smash rocks protruding into the Double Jack 10 lb. foundation ea.

used to excavate retaining structure foundation, load Mini Excavator, 4' overall width wheelbarrows and toters and place fill on top of fabric ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. used to compact loose soils in foundation and soil or Tamper 10" x10", 15 lb. aggregate placed on fabric ea. used to compact loose soils in foundation and soil or Viberplate Compactor 180 lb. aggregate placed on fabric ea. Dolmar gas container for viberplate compactor ea. used to carry tools to worksite or transport soil being Wheelbarrow used for fill material elsewhere or crush fill ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 1,500 lb. Capacity on top of fabric ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 2,500 lb. Capacity on top of fabric ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 3,500 lb. Capacity on top of fabric ea. 5 Gallon Fuel Can gas container for toters ea. 3/8" Rebar Staples 12" Wide x used to pin and secure geotextile fabric to the rear of 18" Long the wall ea. used to cut geotextile fabric to designed length and cut Utility Knife holes in fabric where staples are drive through it ea. Double Jack 8 lb. used to drive rebar staples into the ground ea.

used to monitor how level each course is and the Carpenter's Level 4' prescribed tilt back for the foundation and each course ea.

used to monitor how level each course is and the Smart Level prescribed tilt back for the foundation and each course ea. Cellular Confinement Retaining Structures Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for cellular confinement Level retaining structure ea.

used with clinometer or abney hand level to layout 25' Tape Measure foundations for cellular confinement retaining structure ea.

used with clinometer or abney hand level to layout 100' Tape Measure foundations for cellular confinement retaining structure ea. used to layout foundations for cellular confinement Pin Flags retaining structures bundle used to rake organics off the structure footprint and McLeod shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils and cast excavated soil off the foundation, load soil into wheel barrow or toter Round Point Shovel or shovel backfill into cells ea. used to excavated and shape the bottom of the foundation or load soil into wheel barrow or toter or Square Point Shovel shovel backfill material into cells ea. used to dig out smaller rocks protruding into the Pinch Point Crow Bar 60" foundation ea. used to break or smash rocks protruding into the Double Jack 10 lb. foundation ea.

Hand Saw Cross Cut used to cut cell strips to the proper length and width ea. Circular Saw 71/4" Cordless With Plywood Blade used to cut cell strips to the proper length and width ea. Extra Battery Packs used to power circular saw ea. Staple Pliers used to staple cell strips together ea. Cordless Drill 1/2" used to perforate cells if drainage is required ea. Battery Pack used to power circular saw ea.

Drill Bit Twist 1/2" used with drill to perforate cells if drainage is required ea.

used to excavate retaining structure foundation, load Mini Excavator, 4' overall width wheelbarrows and toters and place fill into cells ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. used to compact loose soils in foundation and soil or Tamper 10" x10", 15 lb. aggregate placed into cells ea. used to compact loose soils in foundation and final trail Viberplate Compactor 180 lb. tread on top of wall ea. Dolmar gas container for viberplate compactor ea. used to carry tools to worksite or transport soil being Wheelbarrow used for fill material elsewhere or crush fill ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 1,500 lb. Capacity in cells ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 2,500 lb. Capacity in cells ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill material Toter 3,500 lb. Capacity in cells ea. 5 Gallon Fuel Can gas container for toters ea.

3/8" Rebar Spreader used to spread and keep cells open while being filled ea.

used to monitor how level each course is and the Carpenter's Level 4' prescribed tilt back for the foundation and each course ea.

used to monitor how level each course is and the Smart Level prescribed tilt back for the foundation and each course ea. Gabion Basket Retaining Structures Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for gabion basket retaining Level structure ea.

used with clinometer or abney hand level to layout 25' Tape Measure foundations for gabion basket retaining structure ea.

used with clinometer or abney hand level to layout 100' Tape Measure foundations for gabion basket retaining structure ea. used to layout foundations for gabion basket retaining Pin Flags structures bundle used to rake organics off the structure footprint and McLeod shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea.

used to excavate loamy soils and cast excavated soil off the foundation, load soil into wheel barrow or toter Round Point Shovel and shovel trail tread material on top of baskets ea. used to excavate and shape the bottom of the foundation or load soil into wheel barrow or toter and Square Point Shovel shovel trail tread material on top of baskets ea. used to dig out smaller rocks protruding into the Pinch Point Crow Bar 60" foundation ea. used to break or smash rocks protruding into the Double Jack 10 lb. foundation ea. used to excavate retaining structure foundation, load wheelbarrows and toters, place rocks into baskets Mini Excavator, 4' overall width and tread material over baskets ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. Tamper 10" x10", 15 lb. used to compact loose soils in foundation ea. used to compact loose soils in foundation and final trail Viberplate Compactor 180 lb. tread on top of wall ea. Dolmar gas container for viberplate compactor ea. used to carry tools to worksite or transport soil being used for fill material elsewhere or rocks used to fill Wheelbarrow baskets ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 1,500 lb. Capacity transport rocks being used to fill baskets ea.

used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 2,500 lb. Capacity transport rocks being used to fill baskets ea.

used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans, and Toter 3,500 lb. Capacity transport rocks being used to fill baskets ea. 5 Gallon Fuel Can gas container for toters ea. Long Nose Pliers Used to crimp the ends of spiral binders ea.

used to monitor how level each course is and the Carpenter's Level 4' prescribed tilt back for the foundation and each course ea.

used to monitor how level each course is and the Smart Level prescribed tilt back for the foundation and each course ea. Project: Drainage Structure Construction

Armored Drain Swale and Stream Crossings, Rock Culverts, Energy Dissipaters, Drain Lense, Step Stone Crossing Structures, Rock Causeways and Turnpikes

Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for drainage crossing Level structures ea. used to layout causeway locations and finished Form Stakes 5' elevations ea. used with form stakes to layout causeway locations String Line and finished elevations roll used to rake organics off the structure footprint and McLeod shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils or load them into wheel Round Point Shovel barrow or toter ea. used to load excavated material into wheel barrow or Square Point Shovel toter ea. used to dig out smaller rocks protruding into the foundation, move larger rocks into position and lever Pinch Point Crow Bar 60" rocks together ea. Tamper 10" x10", 15 lb. used to compact loose soils in foundation ea. used to break or smash rocks protruding into the Double Jack 10 lb. foundation ea. used to break or smash rocks protruding into the Single Jack 4lb. foundation ea. used to excavate foundation, load wheelbarrows and Mini Excavator, 4' overall width toters and place rocks ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation and place rocks ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. used to carry stones to worksite or to location where Rock Litter they are placed in the structure. ea.

used to carry tools and stones to worksite or transport Wheelbarrow soil being used for fill material elsewhere ea.

used to carry tools, stones and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 1,500 lb. Capacity material for structures outside of drainage ea. used to carry tools, stones and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 2,500 lb. Capacity material for structures outside of drainage ea.

used to carry tools, stones and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 3,500 lb. Capacity material for structures outside of drainage ea. 5 Gallon Fuel Can gas container for toters ea. Rigging Equipment For Drainage Structure See Rigging Operations (Highleads and Skylines, Construction Transverse Anchors and Highleads off of Skylines used to measure stones for sorting, breaking and Tape Measure 25' shaping ea.

Chalk used to mark stones for sorting, breaking and shaping ea. Striking Hammer 8lb. used to strike slab and rifting hammers ea. Slab Hammer 8lb. used to split and shape rock ea. Rifting Hammer 8lb. used to split and shape rock ea. Cutter's Hammer used to strike steel rock shaping tools ea.

Hand Tracer Carbide 11/8"x3" used to score line on stone where it is to be broken ea. Hand Point Carbide 1" used to take off high points on stone ea. used to take off high points on stone, remove small Hand Chisel Carbide 1" ledges or score lines ea.

Drift Pin Straight 1/4" Point used to set small rocks in the gaps between rocks ea.

Drift Pin Straight 3/8" Point used to set small rocks in the gaps between rocks ea. used to remove material parallel to a flat stone or to Hand Set Carbide 11/8" x 3" remove drill marks ea. Hammer Point Carbide 3lb. used to remove high points and shape stone ea. Spalling Hammer 4lb. used to break and shape rock ea. Cross Pien Hammer used to break and shape rock ea. Mason (Mash) Hammer 6lb. used to break and crush rock for gaps ea. Log/Lumber Turnpikes Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations for single tier log or lumber Level retaining walls ea.

used with clinometer or abney hand level to layout 25' Tape Measure foundations for single tier log or lumber retaining walls ea.

Carpenter's Level 4' used to monitor how level the foundation and logs are ea.

Smart Level used to monitor how level the foundation and logs are ea. buck down logs used for turnpike wall and cut lap Chainsaw With 24" Bar joints where turnpike logs join ea. Chainsaw With 36" Bar buck down logs used for turnpike wall ea. Chainsaw With 48" Bar buck down logs used for turnpike wall ea. cover over chainsaw bar to facilitate carrying the Bar Covers (scabbard) chainsaw safely ea.

chainsaw tools, file guides, files, file handles, drop Chainsaw Saw Box center depth gauge, extra saw chain, grease gun ea. hardened carbide saw chain used when sawing through down trees or stumps with soil and small Carbide Saw Chain aggregate ea. Dolmar saw gas and bar oil container ea. High Impacting Plastic Wedges 8" wedges used to keep saw kerf open while bucking ea. High Impacting Plastic Wedges 10 1/2" wedges used to keep saw kerf open while bucking ea. Felling Axe 5lb. used to drive plastic wedges into saw kerf ea. Crosscut Saw Single 3' 6" buck down logs used for turnpike wall ea. Crosscut Saw Double 5' 6" buck down logs used for turnpike wall ea. Crosscut Saw Double 7' buck down logs used for turnpike wall ea. fire hose cover over saw teeth to facilitate carrying the Bar Covers (scabbard) crosscut saw safely ea. setting hammer, setting stake, spider set gauge, combination jointer/raker gauge and crosscut Crosscut Saw Box sharpener/jointing file ea.

Lubricant Spray Bottle spray bottle with diesel oil to lubricate crosscut saw ea. Cutter Mattock used to excavate footing and remove roots ea. Pick Mattock used to excavate footing and remove small rocks ea. Pulaski used to excavate footing and remove roots ea. Round Point Shovel used to excavate footing and shape footing to log ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate footing and place smaller logs in Mini Excavator, 4' overall width footing ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation and place logs ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. Stringer Cart used to transport logs or lumber to structure site ea. Trail Cart used to transport logs or lumber to structure site ea.

used to carry tools, fuel and materials to worksite and Wheelbarrow transport footing soil to sites needing fill material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 1,500 lb. Capacity material for structures ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 2,500 lb. Capacity material for structures ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 3,500 lb. Capacity material for structures ea. 5 Gallon Fuel Can gas container for toters ea.

Rigging Equipment For Log See Rigging Operations (Highleads and Skylines, Turnpike Construction Transverse Anchors and Highleads off of Skylines Peavy used to roll and rotate logs into footing ea. Cant Hook used to roll and rotate logs into footing ea. Timber Carrier used to lift, carry or rotate logs into footing ea. Pinch Point Crow Bar 60" used to roll or lever logs into footing ea. Peeler Bar 6' used to roll or lever logs into footing ea. Gas Powered Drill 1/2" used to drill hole through log ea. Auger Drill Bit 9/16" Dia. used to drill hole through log ea. Double Jack 10 lb. used to drive 5/8" rebar through log ea.

Viberplate Compactor 180 lb. used to compact trail tread behind turnpike wall ea. Dolmar gas container for viberplate compactor ea. Wallless Turnpikes Tool/Equipment Function/Use No. Unit used to scarify trail, remove roots and excavate Cutter Mattock parallel ditches ea. Pick Mattock used to scarify trail and excavate parallel ditches ea. used to scarify trail, remove roots and excavate Pulaski parallel ditches ea. used to excavate and shape ditches and used to load Round Point Shovel soil or aggregate into wheel barrow or toter ea. used to load soil or aggregate into wheel barrow or Square Point Shovel toter ea. McLeod used to shape soil or aggregate used for turnpike ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to scarify trail, remove roots and excavate Mini Excavator, 4' overall width parallel ditches ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. tools for servicing and repairing dozer, Tool Box For Excavator, Toters excavator,toters and other large power equipment and Other Power Equipment and installing attachments ea.

used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea.

used to carry tools, fuel and materials to worksite and Wheelbarrow transport soil or aggregate used to build turnpike ea.

used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, Toter 1,500 lb. Capacity and transport soil or aggregate used to build turnpike ea.

used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, Toter 2,500 lb. Capacity and transport soil or aggregate used to build turnpike ea.

used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, Toter 3,500 lb. Capacity and transport soil or aggregate used to build turnpike ea. 5 Gallon Fuel Can gas container for toters ea.

Viberplate Compactor 180 lb. used to compact trail tread behind turnpike wall ea. used to load soil or aggregate into wheel barrow or Round Point Shovel toter ea. used to load soil or aggregate into wheel barrow or Square Point Shovel toter ea. McLeod used to shape soil used for turnpike ea.

Viberplate Compactor 180 lb. used to compact trail tread ea. Dolmar gas container for viberplate compactor ea. Tamper 10" x10", 15 lb. used to compact trail tread ea. Carpenter's Level 4' used to monitor trail cross slope ea. Smart Level used to monitor trail cross slope ea. Metal, Plastic and Wood Culverts Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand Level used to layout footings for culverts ea. used to rake organics off the structure footprint and McLeod shape the bottom of the footing ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the footing ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils or load them into wheel Round Point Shovel barrow or toter and place soil over culvert ea. used to load excavated material into wheel barrow or Square Point Shovel toter and place soil over culvert ea. used to dig out smaller rocks protruding into the Pinch Point Crow Bar 60" footing ea. used to compact loose soils in footing and around Tamper 10" x10", 15 lb. culvert ea. used to compact loose soils in footing and around Rammer Compactor 10" Foot culvert ea. Dolmar 2 cycle gas container for rammer compactor ea. used to break or smash rocks protruding into the Double Jack 10 lb. foundation ea. used to excavate footing, load wheelbarrows and Mini Excavator, 4' overall width toters and backfill over culvert ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment footing ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. Stringer Cart used to transport culvert to structure site ea. Trail Cart used to transport culvert to structure site ea. Rope Nylon 1/2" used to lower culvert on to excavated footing ea. Ratchet 3/8" Drive, Socket Set and Wrenches used to tighten band couplers ea. used to carry headwall stones to worksite or to Rock Litter location where they are placed in the structure. ea.

used to carry tools and stones to worksite or transport Wheelbarrow soil being used for fill material elsewhere ea.

used to carry tools, stones and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 1,500 lb. Capacity material for structures outside of drainage ea.

used to carry tools, stones and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 2,500 lb. Capacity material for structures outside of drainage ea.

used to carry tools, stones and materials to worksite, transport mini excavator attachments and fuel cans, and transport soil or aggregate being used for fill Toter 3,500 lb. Capacity material for structures outside of drainage ea. 5 Gallon Fuel Can gas container for toters ea.

Viberplate Compactor 180 lb. used to compact trail tread over culvert ea. Dolmar gas container for viberplate compactor ea. used to drill pilot holes in wood culvert boards or drive Cordless Drill 1/2" wood screws into boards ea. used with cordless drill to drill pilot holes in wood Wood Drill Bit 7/32" culvert boards ea. used with cordless drill to drive 5" wood screws into Wood Screw Driver Bit wood culvert boards ea. Hammer 20 oz. Rip Claw used to drive 50d nails into culvert boards ea. used to measure headwall stones for sorting, breaking Tape Measure 25' and shaping ea. used to mark headwall stones for sorting, breaking Chalk and shaping ea. Striking Hammer 8lb. used to strike slab and rifting hammers ea. Slab Hammer 8lb. used to split and shape rock ea. Rifting Hammer 8lb. used to split and shape rock ea. Cutter's Hammer used to strike steel rock shaping tools ea.

Hand Tracer Carbide 11/8"x3" used to score line on stone where it is to be broken ea. Hand Point Carbide 1" used to take off high points on stone ea. used to take off high points on stone, remove small Hand Chisel Carbide 1" ledges or score lines ea. used to remove material parallel to a flat stone or to Hand Set Carbide 11/8" x 3" remove drill marks ea. Hammer Point Carbide 3lb. used to remove high points and shape stone ea. Spalling Hammer 4lb. used to break and shape rock ea. Cross Pien Hammer used to break and shape rock ea. Wood and Rock Waterbars Tool/Equipment Function/Use No. Unit used to rake organics off the structure footprint and McLeod shape trail tread in front of culvert ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea.

used to excavate loamy soils and shape the bottom of Hazel Hoe the footing and trail tread in front of culvert ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils and place them on Round Point Shovel downhill side of culvert ea. used to dig out smaller rocks protruding into the Pinch Point Crow Bar 60" footing ea. used to carry waterbar stones to worksite or to location Rock Litter where they are placed in the structure. ea. used to carry tools, materials and stones to worksite or transport soil/aggregate being used for trail tread Wheelbarrow material ea. used to carry tools, materials and stones to worksite or transport soil/aggregate being used for trail tread Toter 1,500 lb. Capacity material ea. used to carry tools, materials and stones to worksite or transport soil/aggregate being used for trail tread Toter 2,500 lb. Capacity material ea. 5 Gallon Fuel Can gas container for toters ea. used to compact loose soils in footing and around Tamper 10" x10", 15 lb. waterbar ea. used to compact trail tread in the front and back of the Viberplate Compactor 180 lb. waterbar ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. Dolmar gas container for viberplate compactor ea. Gas Powered Drill 1/2" used to drill hole through wood waterbar ea. Auger Drill Bit 9/16" Dia. used to drill hole through wood waterbar ea. Dolmar gas container for gas powered drill ea. Double Jack 10 lb. used to drive 5/8" rebar through wood waterbar ea. used to measure waterbar stones for sorting, breaking Tape Measure 25' and shaping ea. used to mark waterbar stones for sorting, breaking Chalk and shaping ea. Striking Hammer 8lb. used to strike slab and rifting hammers ea. Slab Hammer 8lb. used to split and shape rock ea. Rifting Hammer 8lb. used to split and shape rock ea. Cutter's Hammer used to strike steel rock shaping tools ea. Hand Tracer Carbide 11/8"x3" used to score line on stone where it is to be broken ea. Hand Point Carbide 1" used to take off high points on stone ea. used to take off high points on stone, remove small Hand Chisel Carbide 1" ledges or score lines ea. used to remove material parallel to a flat stone or to Hand Set Carbide 11/8" x 3" remove drill marks ea. Hammer Point Carbide 3lb. used to remove high points and shape stone ea. Spalling Hammer 4lb. used to break and shape rock ea. Cross Pien Hammer used to break and shape rock ea. Project: Timber Planking, Puncheon and Boardwalk Structure Construction Timber Planking Structures Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand Level used to layout footings and timber planking sills ea. used with clinometer or abney hand level to layout 25' Tape Measure footings for timber planking sills ea. Form Stakes used to layout curved timber planking ea. used to turn form stakes to line up the holes in the 12" Aluminum Pipe Wrench stakes ea. String Line used to layout curved timber planking roll

used to remove dense vegetation "tussocks and Cutter Mattock tundra mat", excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils, and shape and level the Hazel Hoe log sill footing ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. Round Point Shovel used to excavate wet loamy soils ea. Tamper 10" x10", 15 lb. used to compact log sill footing ea. Tools To Fabricate Sills and Planks See Native Material Fabrication Framing Square used to layout and scribe curved planking cuts ea. Carpenter's Pencil used to scribe curved planking cuts ea. used to cut angles on planking used in curved Hand Saw Cross Cut planking applications ea. used to cut angles on planking used in curved Cordless Circular Saw 7 1/4" planking applications ea. Extra Battery Packs charged battery packs for circular saw ea. Circular Saw 7 1/4" Combination Saw Blades extra saw blades ea. used to cut angles on planking used in curved Chainsaw With 16" Bar planking applications ea. cover over chainsaw bar to facilitate carrying the Bar Covers (scabbard) chainsaw safely ea. chainsaw tools, file guides, files, file handles, drop Chainsaw Saw Box center depth gauge, extra saw chain, grease gun ea. Trail Cart used to transport sills and planking to structure site ea.

used to carry tools, fuel and materials to worksite and Wheelbarrow transport footing soil to sites needing fill material ea.

used to carry tools, fuel and materials to worksite and Toter 1,500 lb. Capacity transport footing soil to sites needing fill material ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea.

used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea.

used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Can gas container for toters ea. Timber Carrier used to lift, carry or rotate sills into footing ea. Peavy used to roll and rotate sills into footing ea. Gas Powered 1/2" Drill used to drill pilot holes for 5/8" rebar and 7" spikes ea. Dolmar gas container for chainsaw and 1/2" drill ea. Cordless Drill 1/2" used to drill pilot holes for 70d nails ea. Extra Battery Packs charged battery packs for cordless drill ea. Auger Drill Bit 9/16" Dia. used to drill hole for 5/8" rebar through wood sills ea. used to drive form stakes into the ground and drive Double Jack 10 lb. 5/8" rebar through wood sills ea. 1/4" Wood Drill Bit used to drill pilot holes for 7" spikes ea. Hammer 20 oz. Rip Claw used to drive 70d nails into planks ea. Hand Sledge 2lb. used to drive 70d nails into planks ea. Drift Pin Straight 3/8" Point used to set nail heads on 7" spikes ea. Carpenter's Level 4' used to monitor how level the sills and planking are ea. Smart Level used to monitor how level the sills and planking are ea.

Pipe Wrench used to remove auger bits if they get stuck in wood ea. Adjustable Wrench used to remove auger bits if they get stuck in wood ea. used to cut nails or rebar flush when they cannot be Reciprocating Saw driven flush with the sill ea. used to cut nails or rebar flush when they cannot be Metal Cutting Grinder driven flush with the sill ea. Puncheon Structures Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout foundations and sills for puncheon Level structure ea.

used with clinometer or abney hand level to layout 25' Tape Measure foundations and sills for puncheon structure ea.

used with clinometer or abney hand level to layout 50' Cloth Tape Measure foundations and sills for puncheon structure ea. used to establish starting and ending locations and centerline for the puncheon structure, mark the outside location of the sills and mark the outside of the sills on Form Stakes curved puncheons ea. used to turn form stakes to line up the holes in the 12" Aluminum Pipe Wrench stakes ea. used with form stakes to identify the centerline for the puncheon structure and layout of curved puncheon String Line sills roll

Framing Square used with string line to layout curved puncheon sills ea. used to identify the location of the sills and for Ledger Boards squaring up the sills ea. used to identify and maintain the front location of the 12" Spikes sills ea.

used to brush the puncheon footprint , light to medium Powered Brushcutters 36-46cc brush with maximum 1/2" diameter stems ea.

used with clinometer or abney hand level to sight on tape measure and rake organics off the structure McLeod footprint and shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils and cast excavated soil off the foundation and load soil into wheelbarrow or Round Point Shovel toter ea. used to excavated and shape the bottom of the Square Point Shovel foundation or load soil into wheelbarrow or toter ea. used to dig out smaller rocks protruding into the Pinch Point Crow Bar 60" foundation ea. used to drive form stakes into the ground, break or smash rocks protruding into the foundation and drive Double Jack 10 lb. 5/8" rebar through mudsills ea.

Pipe Wrench used to remove auger bits if they get stuck in wood ea.

Adjustable Wrench used to remove auger bits if they get stuck in wood ea. used to cut nails or rebar flush when they cannot be Reciprocating Saw driven flush with the sill ea. used to cut off rebar if rocky soil prohibits driving it to Hacksaw full depth ea. used with hacksaw to cut off rebar if rocky soil Metal Cut Hacksaw Blades prohibits driving it to full depth ea. used to excavate foundation and load soil into Mini Excavator, 4' overall width wheelbarrows or toters ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. Stringer Cart used to transport lumber to structure site ea. Trail Cart used to transport lumber to structure site ea.

used to carry tools, fuel and materials to worksite and Wheelbarrow transport foundation soil to sites needing fill material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 1,500 lb. Capacity material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 2,500 lb. Capacity material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 3,500 lb. Capacity material ea. 5 Gallon Fuel Can gas container for toters ea. Tamper 10" x10", 15 lb. used to compact puncheon foundation ea.

Viberplate Compactor 180 lb. used to compact puncheon foundation ea. Dolmar gas container for viberplate compactor ea.

Timber Carrier used to lift, carry or rotate mudsills onto foundation ea. Peavy used to roll and rotate mudsills onto foundation ea.

used to rip decking and soil dam boards and cut taper Cordless Circular Saw 7 1/4" in decking boards used with curved puncheon ea. Extra Battery Packs charged battery packs for circular saw ea.

used to rip decking and soil dam boards and cut taper Circular Saw 7 1/4" Electric in decking boards used with curved puncheon ea. Circular Saw 7 1/4" Combination Saw Blades extra saw blades ea. Generator 2,500 Watt used to power electric circular saw and drill ea. Power Cord 50' With GFI Water Proof Receptacle used to supply power to electric saw and drill ea. used to support lumber while performing layout, cutting Saw Horse and ripping ea. Tape Measure 25' used to measure decking overhang ea.

Chalk Liner used to mark the center of the joist for nailing decking ea. Bottle of Chalk used to refill chalk liner ea. used to drill pilot holes for 5/8" rebar, 60d and 70d nails and holes for 3/8" carriage bolts if bull rails are Carpenter's Brace Drill installed ea. used with carpenter's brace to drill pilot holes for 5/8" Drill Brace Bit Set 1/4"-1", 9 rebar, 60d and 70d nails and holes for 3/8" carriage 1/2" long bolts if bull rails are installed set used to drill pilot holes for 5/8" rebar, 60d and 70d nails and holes for 3/8" carriage bolts if bull rails are Gas Powered 1/2" Drill installed ea. Dolmar gas container for chainsaw and 1/2" drill ea.

Ship Auger Drill Bit 9/16" Dia. used to drill hole for 5/8" rebar through wood sills ea. Cordless Drill 1/2" used to drill pilot holes for 60d and 70d nails ea. Extra Battery Packs charged battery packs for cordless drill ea. used to drill pilot holes for 5/8" rebar, 60d and 70d nails and holes for 3/8" carriage bolts if bull rails are Electric Drill 1/2" installed ea.

7/32" x 6" Wood Twist Drill Bit used to drill pilot holes for 60d nails ea.

1/4" x 6" Wood Twist Drill Bit used to drill pilot holes for 70d nails ea.

3/8" x 6" Wood Twist Drill Bit used to drill holes for 3/8" carriage bolts ea. C Clamp 12 1/2" Opening x 6 used to hold bull rails in place while drilling and 1/4" Throat Opening fastening ea. Wooden Hand Screw Clamp, used to hold bull rails in place while drilling and 18" Opening fastening ea. used to treat sawn cuts and holes in pressure treated 1 Gallon Of Wood Preservative wood gal. used to contain wood preservative while it is being Plastic Pale 1/2 Gal. applied to pressure treated wood. ea. Paint Brush used to apply wood preservative (cut ends) ea. Bottle Brush used to apply wood preservative (holes) ea. used to protect hands while applying wood Rubber Gloves preservative pair

Hammer 20 oz. Rip Claw used to drive 60d nails into decking and soil dams ea.

Hand Sledge 2lb. used to drive 60d nails into decking and soil dams ea. Drift Pin Straight 3/8" Point used to set nail heads on 60d and 70d nails ea. Crowbar 2' used to pull nails ea. Cordless Drill 1/2" used to drive 6" decking screws into decking ea.

Wood Screw Driver Bit used with cordless drill to drive 6" screws into decking ea. Battery Pack used as additional power source for cordless drill ea. used to tighten bolts and nuts used to assemble bull Ratchet 1/2" Drive rail ea. Extension 1/2" Drive 4" used with ratchet ea. Deep Well Socket Set 5/16"-1 used with ratchet to tighten bolts and nuts used to 1/2" assemble bull rail ea. Carpenter's Adz used to level hand split decking if used ea. Chainsaw With Log Wizard Attachment used to level hand split decking if used ea. used to support lumber while performing layout, cutting Saw Horse and ripping ea. Cloth Tool/Nail Apron used to hold tools and fasteners ea. Leather Tool/Nail Belt used to hold tools and fasteners ea. used to monitor how level the foundation, sills and Carpenter's Level 4' decking are ea. used to monitor how level the foundation, sills and Smart Level decking are ea. used to rake up wood shavings and debris on and Leaf Rake around structure ea. used to sweep up saw dust and wood shavings on Push Broom 24" Heavy Bristle deck ea. used to pick up saw dust and debris swept from Dust Pan decking ea. Plastic Lawn and Leaf Bags used to collect and store sawdust, wood shavings and Extra Strong 39 Gal. debris box Job Security Box used to secure and store tools at job site ea. Boardwalk Structures Tool/Equipment Function/Use No. Unit used to layout form stakes, batter boards and string lines, square up batter boards and square up string 50' Cloth Tape Measure lines using the 3-4-5 measurement ea. used to layout form stakes, batter boards and string lines, square up batter boards and square up string 100' Cloth Tape Measure lines using the 3-4-5 measurement ea. used to establish center line, starting and ending Form Stakes locations and support for batter boards ea.

used with form stakes and batter boards to identify the centerline, starting and ending locations and locations String Line of sills or piers used to support the boardwalk structure roll used to turn form stakes to line up the holes in the 12" Aluminum Pipe Wrench stakes ea. Clinometer or Abney Hand used to identify ground elevations needed for locating Level auto level ea. used with clinometer or abney hand level to identify 25' Tape Measure ground elevations ea. used to layout boardwalk foundation and batter board Auto Level With Tripod elevations ea. used with auto level to layout boardwalk foundation, Stadia Rod In Feet and Inches sill, and pier elevations ea.

used with clinometer or abney hand level to sight on tape measure and rake organics off the structure McLeod footprint and shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils, cast excavated soil off the foundation, load soil into wheelbarrow or toter and Round Point Shovel excavate pier footings ea. used to excavated and shape the bottom of the Square Point Shovel foundation or load soil into wheelbarrow or toter ea. used to dig out smaller rocks protruding into the Pinch Point Crow Bar 60" foundation ea.

used to drive form stakes into the ground, break or smash rocks protruding into the foundation, drive 5/8" Double Jack 10 lb. rebar through mudsills and drive diamond pier pins ea.

Pipe Wrench used to remove auger bits if they get stuck in wood ea.

Adjustable Wrench used to remove auger bits if they get stuck in wood ea. used to cut nails or rebar flush when they cannot be Reciprocating Saw driven flush with the sill ea. used to cut off rebar if rocky soil prohibits driving it to Hacksaw full depth ea. used with hacksaw to cut off rebar if rocky soil Metal Cut Hacksaw Blades prohibits driving it to full depth ea. used to excavate foundation and load soil into Mini Excavator, 4' overall width wheelbarrows or toters ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. Tamper 10" x10", 15 lb. used to compact boardwalk foundation ea.

Viberplate Compactor 180 lb. used to compact boardwalk foundation ea. Dolmar gas container for viberplate compactor ea. Stringer Cart used to transport lumber to structure site ea. Trail Cart used to transport lumber to structure site ea. used to carry tools, fuel and materials to worksite, transport foundation soil to sites needing fill material Wheelbarrow and mix concrete ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 1,500 lb. Capacity material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 2,500 lb. Capacity material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 3,500 lb. Capacity material ea. 5 Gallon Fuel Can gas container for toters ea. used to layout batter board form stakes, square up batter board string lines, layout and scribe lines for pier, header, joist, post, decking, railing, soil dam and Framing Square bull rail cuts and notching ea. attached to form stakes and used to layout and square 1" x 6 " Batter Boards up the boardwalk structure ea.

used to drill holes through batter boards, piers, headers, joist and post, also drill pilot holes through Carpenter's Brace Drill piers, headers, joists, decking, post and railing ea. used with carpenter's brace to drill holes through batter boards, piers, headers, joist and post, also drill Drill Brace Bit Set 1/4"-1", 9 pilot holes through piers, headers, joists, decking, post 1/2" long and railing set used to drill holes through batter boards, piers, headers, joist and post, also drill pilot holes through Cordless Drill 1/2" piers, headers, joists, decking, post and railing ea. Battery Pack used as additional power source for cordless drill ea. used to drill holes through batter boards, piers, headers, joist and post, also drill pilot holes through Gas Powered Drill 1/2" piers, headers, joists, decking, post and railing ea. Dolmar gas container for 1/2" drill ea. used to drill holes through batter boards, piers, headers, joist and post, also drill pilot holes through Electric Drill 1/2" piers, headers, joists, decking, post and railing ea. Generator 2,500 Watt used to power electric circular saw and drill ea. Power Cord 50' With GFI Water Proof Receptacle used to supply power to electric saw, drill and jig saw ea. Auger Drill Bit 9/16" Dia. used to drill hole for 5/8" rebar through mudsills ea. used to drill pilot holes for 16d nails, 1/8" machine 1/8" x 6" Wood Twist Drill Bit screws and deck screws ea.

3/16" x 6" Wood Twist Drill Bit used to drill pilot holes for 40d nails ea.

3/8" x 6" Wood Twist Drill Bit used to drill holes for 3/8" carriage bolts ea. 1/8" x 3" Machine Screw and Nut used to attach the batter boards to the form stakes ea.

16d duplex nails used to attach the batter boards to the form stakes lbs. used to attach the string lines to top of the batter 8d duplex nails boards lbs. used to drive the 16d duplex nails through form stakes batter boards and the 8d duplex nail into the top of Hammer 16 oz. Rip Claw batter board ea. used to layout locations for batter board string lines and pier post, headers, joist, post, decking, hand rails, 25' Tape Measure bull rails and soils dams layout and cuts ea. used to scribe lines for batter board string lines, pier, header, joist, post, decking, railing, soil dam and bull Carpenter's Pencil rail cuts and notching ea. used to scribe locations for batter board string lines and pier post, headers, joist, post, decking, hand rails, Combination Square bull rails and soils dams cuts ea. used to scribe locations for batter board string lines and pier post, headers, joist, post, decking, hand rails, Speed Square bull rails and soils dams cuts ea. used to mark locations on string line for side batter Felt Tip Marker boards ea. used with string lines to identify the center of pier Plumb Bob blocks, diamond piers and helical anchors ea. used with plumb bob to identify the center of pier 40d nails blocks, diamond piers and helical anchors ea. used with 40d nails to identify the center of pier blocks, Rolled Flagging diamond piers and helical anchors roll used to treat sawn cuts and holes in pressure treated 1 Gallon Of Wood Preservative wood gal. used to contain wood preservative while it is being Plastic Pale 1/2 Gal. applied to pressure treated wood. ea. Paint Brush used to apply wood preservative (cut ends) ea. Bottle Brush used to apply wood preservative (holes) ea. used to protect hands while applying wood Rubber Gloves preservative pair Timber Carrier used to lift, carry or rotate sills onto foundation ea. Peavy used to roll and rotate sills onto foundation ea.

ATV With Trailer/Water Tank used to supply water to mix with concrete ea. Water Bucket 5 Gal. used to supply water to mix with concrete ea. container used to mix concrete and water used in pier Concrete Mixing Tub footing ea. Concrete Mixing Hoe tool used to mix concrete and water ea.

Brick Trowel used to apply, level and shape concrete under piers ea. Cobra Combi Gas Powered Rock Drill and Breaker used to drive diamond pier pins into ground ea. used with rock drill/breaker to drive diamond pier pins Driving Head into ground ea. Dolmar breaker gas/two cycle oil mix container ea. used to monitor surface of diamond pier and ensure Torpedo Level that it is level ea. used to cut off pins when they can't be driven fully into Electric Reciprocating Saw ground ea. used with reciprocating saw to cut off pins when they Steel Cutting Saw Blade can't be driven fully into ground ea. used to cut off pins when they can't be driven fully into Pipe Cutter ground ea. Gas Powered Hole Auger, Two Person use to screw helical anchors into ground ea. Drive Head Adapter used to attach hole auger to the helical anchor ea. used to tighten bolts and nuts used to assemble Ratchet 1/2" Drive boardwalk components ea. Extension 1/2" Drive 4" used with ratchet ea. Deep Well Socket Set 5/16"-1 used with ratchet to tighten bolts and nuts used to 1/2" assemble boardwalk components ea. Combination Wrench Set 5/16"- used to tighten bolts and nuts used to assemble 1 1/2" boardwalk components ea. used to cut pier post, headers, joist, post, decking, railing, bull rails and soil dams to prescribed angles and lengths and rip decking and soil dam boards to Cordless Circular Saw 7 1/4" prescribed widths ea. Extra Battery Packs charged battery packs for circular saw ea. used to cut pier post, headers, joist, post, decking, railing, bull rails and soil dams to prescribed angles and lengths and rip decking and soil dam boards to Circular Saw 7 1/4" Electric prescribed widths ea. Circular Saw 7 1/4" Combination Saw Blades extra saw blades ea. used to support lumber while performing layout, cutting Saw Horse and ripping ea. Tape Measure 25' used to measure decking overhang ea.

Chalk Liner used to mark the center of the joist for nailing decking ea. Bottle of Chalk used to refill chalk liner ea. used to drive 40d nails into decking and railing and Hammer 20 oz. Rip Claw 60d nails into soil dams ea. used to drive 40d nails into decking and railing and Hand Sledge 2lb. 60d nails into soil dams ea. used to drive 40d nails into decking and railing and Single Jack 4lb. 60d nails into soil dams ea. Drift Pin Straight 1/4" Point used to set nail heads on 40d nails ea. Drift Pin Straight 3/8" Point used to set nail heads on 60d nails ea.

Wood Screw Driver Bit used with drills to drive 5" decking screws into decking ea. Crowbar 2' used to pull nails ea. used to monitor how plumb post are and used with Carpenter's Level 2' carpenter's pencil to scribe lines ea. C Clamp 12 1/2" Opening x 6 used to hold post, bull rails and diagonal railing in 1/4" Throat Opening place while drilling and scribing ea. Wooden Hand Screw Clamp, used to hold post, bull rails and diagonal railing in 18" Opening place while drilling and scribing ea. used to hold post, bull rails and diagonal railing in Bar Clamp 24" Opening place while drilling and scribing ea. Handsaw Crosscut used to cut out notches on decking and handrails ea. Handsaw Ripping used to rip boards to proper width and taper ea. Keyhole Saw used to cut out notches on decking ea. Coping Saw used to cut out notches on decking ea. Electric Jig Saw used to cut out notches on decking ea. used to drill holes in corners of notching layouts to 3/4" Speed Bore Drill Bit allow saw to cut out notches ea.

Beveled used to break out wood between saw cuts on notches ea. used to break out wood between saw cuts and shape Wood Chisel 1" bottom of notches ea. used to break out wood between saw cuts and shape Wood Chisel 1 1/2" bottom of notches ea. used to break out wood between saw cuts and shape Wood Chisel 2" bottom of notches ea. used to shape the bottom and sides of the notches Rasp, Surform Flat Bottom and smooth railing surfaces ea. Rasp Blades replacement blades for surform rasp ea. Drawknife 9" Straight Blade used to hewn posts and railings ea. Chainsaw With Log Wizard Attachment used to hewn posts and railings ea. used with sand paper to smooth surface of posts and Sanding Block railing ea. used with sanding block to smooth surface of posts Sandpaper 80 Grit and railing sheet Cloth Tool/Nail Apron used to hold tools and fasteners ea. Leather Tool/Nail Belt used to hold tools and fasteners ea. used to monitor how level and plumb boardwalk Carpenter's Level 4' structural members are ea. used to monitor how level and plumb boardwalk Smart Level structural members are ea. used to rake up wood shavings and debris on and Leaf Rake around structure ea. used to sweep up saw dust and wood shavings on Push Broom 24" Heavy Bristle deck ea. used to pick up saw dust and debris swept from Dust Pan decking ea. Plastic Lawn and Leaf Bags used to collect and store sawdust, wood shavings and Extra Strong 39 Gal. debris box Job Security Box used to secure and store tools at job site ea. Project: Bridge Structure Construction Tool/Equipment Function/Use No. Unit used to layout form stakes, batter boards and string lines, square up batter boards and square up string 50' Cloth Tape Measure lines using the 3-4-5 measurement ea. used to layout form stakes, batter boards and string lines, square up batter boards and square up string 100' Cloth Tape Measure lines using the 3-4-5 measurement ea. used to layout form stakes, batter boards and string lines, square up batter boards and square up string 200' Cloth Tape Measure lines using the 3-4-5 measurement ea.

used to identify the centerline, starting and ending locations and support batter boards used to layout locations of sills, beam seats, J bolts, beam seat Form Stakes brackets and soil dams and support concrete forms ea. used with form stakes and batter boards to identify the centerline, starting and ending locations and locations of sills, beam seats, J bolts, beam seat brackets and String Line soil dams roll used to mark locations on string line for side batter Felt Tip Marker boards ea. used to turn form stakes to line up the holes in the 12" Aluminum Pipe Wrench stakes ea. Clinometer or Abney Hand used to identify ground elevations needed for locating Level auto level ea. used with clinometer or abney hand level to identify 25' Tape Measure ground elevations ea. used to layout bridge foundations and batter board Auto Level With Tripod elevations ea. used with auto level to layout bridge foundations and Stadia Rod In Feet and Inches batter board elevations ea.

used with clinometer or abney hand level to sight on tape measure and rake organics off the structure McLeod footprint and shape the bottom of the foundation ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the bottom of Hazel Hoe the foundation ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to excavate loamy soils, cast excavated soil off the foundation, load soil into wheelbarrow or toter and Round Point Shovel excavate footings ea. used to excavated and shape the bottom of the Square Point Shovel foundation or load soil into wheelbarrow or toter ea. used to dig out smaller rocks protruding into the foundation, lever bridge stringers into position and spread bridge stringers apart when placing Pinch Point Crow Bar 60" diaphragms ea.

used to drive form stakes into the ground, break or smash rocks protruding into the foundation and drive Double Jack 10 lb. 5/8" rebar through wood or plastic mudsills ea. used to cut off rebar if rocky soil prohibits driving it to Hacksaw full depth ea. used with hacksaw to cut off rebar if rocky soil Metal Cut Hacksaw Blades prohibits driving it to full depth ea.

Pipe Wrench used to remove auger bits if they get stuck in wood ea.

Adjustable Wrench used to remove auger bits if they get stuck in wood ea. used to cut nails or rebar flush when they cannot be Reciprocating Saw driven flush with the sill ea. used to excavate foundation and load soil into Mini Excavator, 4' overall width wheelbarrows or toters ea. Excavator Hydraulic Thumb used to grasp and move rocks when excavating Attachment foundation ea. Excavator Hydraulic Breaker Attachment used to break rock and excavate rock and hard soil ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. Tamper 10" x10", 15 lb. used to compact bridge foundations ea.

Viberplate Compactor 180 lb. used to compact bridge foundations ea. Dolmar gas container for viberplate compactor ea. used to transport bridge stringers and mud sills to Stringer Cart structure site ea. Trail Cart used to transport lumber to structure site ea. used to carry tools, fuel and materials to worksite, transport foundation soil to sites needing fill material Wheelbarrow and mix concrete ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 1,500 lb. Capacity material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 2,500 lb. Capacity material ea. used to carry tools, and materials to worksite, transport mini excavator attachments and fuel cans, and transport foundation soil to sites needing fill Toter 3,500 lb. Capacity material ea. 5 Gallon Fuel Can gas container for toters ea. used to layout batter board form stakes, square up batter board string lines, layout and scribe lines for post sills, post, decking, railing, and soil dam cuts and Framing Square notching ea. attached to form stakes and used to layout and square 1" x 6 " Batter Boards up the bridge structure ea. used to drill holes through batter boards, mudsills, trestle sills and braces, form boards, stringers, post sills and post, also drill pilot holes through soil dams, Carpenter's Brace Drill decking, post and railing ea.

used with brace to drill holes through batter boards, mudsills, trestle sills and braces, form boards, Drill Brace Bit Set 1/4"-1", 9 stringers, post sills and post, also drill pilot holes 1/2" long through soil dams, decking, post and railing set used to drill holes through batter boards, mudsills, trestle sills and braces, form boards, stringers, post sills and post, also drill pilot holes through soil dams, Cordless Drill 1/2" decking, post and railing ea. Battery Pack used as additional power source for cordless drill ea.

used to drill holes through batter boards, mudsills, form boards, stringers, post sills and post, also drill Gas Powered Drill 1/2" pilot holes through soil dams, decking, post and railing ea. Dolmar gas container for 1/2" drill ea. used to drill holes through batter boards, mudsills, trestle sills and braces, form boards, stringers, post sills and post, also drill pilot holes through soil dams, Electric Drill 1/2" decking, post and railing ea. used to power electric circular saw, drill, jig saw and Generator 2,500 Watt concrete vibrator ea. Power Cord 50' With GFI used to supply power to electric saw, drill, jig saw and Water Proof Receptacle concrete vibrator ea.

Ship Auger Drill Bit 3/8" x 18" used to drill holes for 3/8" carriage bolts ea. used to drill holes for 1/2" carriage and hex headed Ship Auger Drill Bit 1/2" x 18" bolts and all thread (she bolts) ea. used to drill hole for 5/8" rebar through wood and Ship Auger Drill Bit 9/16" x 18" plastic sills ea. used to drill holes for 5/8" carriage and hex headed bolts and align diaphragm, beam seat bracket and Ship Auger Drill Bit 5/8" x 18" post bolt holes in wood stringers ea. used to drill holes for 3/4" carriage and hex headed bolts and align diaphragm, beam seat bracket and Ship Auger Drill Bit 3/4" x 18" post bolt holes in wood stringers ea. High Speed Steel Drill Bit 1/2" used to align bolt holes in metal diaphragms and x 6" stringers ea. High Speed Metal Drill Bit 5/8" used to align bolt holes in metal diaphragms and x 6" stringers ea. High Speed Metal Drill Bit 3/4" used to align bolt holes in metal diaphragms and x 6" stringers ea. used to drill pilot holes for 16d nails, 1/8" machine 1/8" x 6" Wood Twist Drill Bit screws and deck screws ea.

3/16" x 6" Wood Twist Drill Bit used to drill pilot holes for 40d nails ea.

7/32" x 6" Wood Twist Drill Bit used to drill pilot holes for 60d nails ea.

1/4" x 6" Wood Twist Drill Bit used to drill pilot holes for 70d nails ea.

1/2" x 6" Wood Twist Drill Bit used to drill she bolt holes in form boards ea.

5/8" x 6" Wood Twist Drill Bit used to drill snap tie holes in form boards ea. 1/8" x 3" Machine Screw and Nut used to attach the batter boards to the form stakes ea.

16d duplex nails used to attach the batter boards to the form stakes lbs. used to attach the string lines to top of the batter 8d duplex nails boards lbs. used to drive the 16d duplex nails through form stakes batter boards and the 8d duplex nail into the top of Hammer 16 oz. Rip Claw batter board ea.

used to layout locations for batter board string lines and trestle sills and braces, post sills, post, decking, 25' Tape Measure hand rails, bull rails and soils dams layout ea. used to scribe lines for batter board string lines, trestle sills and braces, post sills, post, decking, railing, soil Carpenter's Pencil dam and bull rail cuts and notching ea. used to scribe locations for batter board string lines and trestle sills and braces, post sills, post, decking, Combination Square hand rails, bull rails and soils dams cuts ea. used to scribe locations for batter board string lines and trestle sills and braces, post sills, post, decking, Speed Square hand rails, bull rails and soils dams cuts ea. used to cut trestle braces, post, decking, railing, bull rails and soil dams to prescribed angles and lengths and rip decking and soil dam boards to prescribed Cordless Circular Saw 7 1/4" widths ea. Extra Battery Packs charged battery packs for circular saw ea. used to cut trestle braces, post, decking, railing, bull rails and soil dams to prescribed angles and lengths and rip decking and soil dam boards to prescribed Circular Saw 7 1/4" Electric widths ea. Circular Saw 7 1/4" Combination Saw Blades saw blades for cross cut and ripping ea. Circular Saw 7 1/4" Plywood Saw Blades saw blades for cutting plywood from boards ea. used to support lumber while performing layout, cutting Saw Horse and ripping ea. used to treat sawn cuts and holes in pressure treated 1 Gallon Of Wood Preservative wood gal. used to contain wood preservative while it is being Plastic Pale 1/2 Gal. applied to pressure treated wood. ea. Paint Brush used to apply wood preservative (cut ends) ea. Bottle Brush used to apply wood preservative (holes) ea. used to protect hands while applying wood Rubber Gloves preservative pair Timber Carrier used to lift, carry or rotate sills onto foundation ea. Peavy used to roll and rotate sills onto foundation ea. used to pick up saw dust and debris swept from Dust Pan decking ea. Plastic Lawn and Leaf Bags used to collect and store sawdust, wood shavings and Extra Strong 39 Gal. debris box

Rock, Wood, Log, Plastic Wood, Cellular Confinement and Gabion Abutments See Retaining Structure Construction Roto Hammer, Gas Powered 1/2" used to drill 5/8" hole in bedrock for rebar ea. 5/8" x 12" Rock Drill Bit used to drill hole in rock for 5/8" rebar ea. Hilti Glue Gun and Glue used to secure rebar in bedrock ea. Rechargeable Aerosol Spray used to blow rock dust out drill holes before gluing Can 200 PSI stainless steel rod ea. Rebar Cutter and Bender used to cut and bend rebar used in concrete forms ea. 9 Gauge Wire used to tie rebar together ea. Metal Tie Straps used to join and secure form board corners ea. used to keep the form boards rigid and from spreading Snap Ties apart ea. used with snap ties to keep the form boards rigid and 2" x 4" Walers from spreading apart ea. used to tighten and hold snap ties and walers together and keep the form boards rigid and from spreading Forming Wedge apart ea. used to keep the form boards rigid and from spreading All Thread 1/2" apart ea. Malleable Bridge Washers and used to tighten and hold all thread and keep the form 1/2" Nuts boards rigid and from spreading apart ea.

Concrete Form Oil used to keep concrete from sticking to form boards can used to contain form oil while it is being applied to One Gallon Pail form boards. ea. Paint Brush used to apply form oil ea. Rubber Gloves used when applying form oil ea. Concrete Transit Truck used to transport mixed concrete to job site ea. Concrete Pump and Hose used to pump mixed concrete to forms ea.

ATV With Trailer/Water Tank used to supply water to mix with concrete ea. used to supply water to mix with concrete and pour Water Bucket 5 Gal. mixed concrete into forms ea. container used to mix concrete and water used in Concrete Mixing Tub concrete sill or abutment ea. Concrete Mixing Hoe tool used to mix concrete and water ea. used to test the consistency or stiffness of the Slump Cone concrete

Concrete Vibrator used to agitate concrete in forms to eliminate voids ea.

Concrete Jitterbug used to agitate concrete in forms to eliminate voids ea.

Brick Trowel used to level and shape concrete sills and abutments ea.

Pointing Trowel used to level and shape concrete sills and abutments ea. used to create an edge and separation between the top of the form boards and the concrete sill or Concrete Edger abutment ea. used to tighten bolts and nuts used to assemble bridge Ratchet 1/2" Drive components ea. used to tighten bolts and nuts used to assemble bridge Breaker Bar 1/2" Drive 15" components ea. Extension 1/2" Drive 4" used with ratchet and breaker bar ea. Deep Well Socket Set 5/16"-1 used with ratchet and breaker bar to tighten bolts and 1/2" nuts used to assemble bridge components ea. Combination Wrench Set 5/16"- used to tighten bolts and nuts used to assemble bridge 1 1/2" components ea. used to tighten bolts and nuts used to assemble bridge Adjustable Wrench 8" components ea. used to tighten bolts and nuts used to assemble bridge Adjustable Wrench 10" components ea. used to tighten bolts and nuts used to assemble bridge Adjustable Wrench 15" components ea. Broad Head Bull Pin 1 1/4" Top used to align bolt holes in metal diaphragms and x 13 3/4" Length stringers ea. Broad Head Bull Pin 1 1/16" used to align bolt holes in metal diaphragms and Top x 10" Length stringers ea. used to align bolt holes in metal diaphragms and Aligning Pry Bar 30" stringers ea.

Rigging Equipment Used to See Rigging Operations (Highleads and Skylines, Construct Abutments Transverse Anchors and Highleads off of Skylines worn by trial workers while assembling bridge and Full Arrest Body Harness anchored to skyline ea. Arbor-Plex Climbing Rope 1/2" tied to body harness to and skyline to secure trail x 30' worker ea. used to secure arbor-plex rope to skyline and slide Carabiner Locking rope along skyline ea. Block, Standard 5", 4 ton WLL attached to skyline and used for moving bridge Min. diaphragms along skyline ea.

2,000 lb. capacity hoist attached to 5" block and used to lift and lower diaphragms into position and pull and hold post sills in position, also used to pull warped Griphoist TU 17 stringers together, includes short mainline and handle ea. Chain, High Test, 5/16"" x 10' Includes Grab Hooks used to attach TU 17 griphoist to diaphragm ea. used to anchor griphoist to stringer when pulling Nylon Sling, eye each end, 2 stringers together and attaching post sill to griphoist ply 4" x 10' (9,200 lb. WLL when holding post sill up against the bottom of the choker set min.) stringers ea. Choker 1/2" x 10' used with TU 17 griphoist to pull stringers together ea.

used to spread bridge stringers apart and lift ends of High Lift Jack stringers to facilitate minor position adjustments ea.

Crowbar 4' used to spread stringers apart and positon diaphragm ea. used to hold post sills in place while drilling and Ratchet Strap attaching to stringer ea. used to hold post sills in place while drilling and Pipe Clamp 30" Opening attaching to stringer ea. Tape Measure 25' used to measure decking overhang ea. used to mark the center of the stringers or nailers for Chalk Liner nailing decking ea. Bottle of Chalk used to refill chalk line ea. used to drive 40d nails into railing and 60d nails into Hammer 20 oz. Rip Claw soil dams and decking ea. Hand Sledge 2lb. used to drive 60d and 70d nails into decking ea. Single Jack 4lb. used to drive 60d and 70d nails into decking ea. Drift Pin Straight 1/4" Point used to set nail heads on 40d nails ea. Drift Pin Straight 3/8" Point used to set nail heads on 60d and 70d nails ea. used with drills to drive 5" and 6" decking screws into Wood Screw Driver Bit decking ea. Crowbar 2' used to pull nails ea.

Carpenter's Level 2' used to layout posts and monitor how plumb post are ea. C Clamp 12 1/2" Opening x 6 used to hold post, bull rails and diagonal railing in 1/4" Throat Opening place while drilling or scribing ea. Wooden Hand Screw Clamp, used to hold post, bull rails and diagonal railing in 18" Opening place while drilling or scribing ea. used to hold post, bull rails and diagonal railing in Bar Clamp 24" Opening place while drilling or scribing ea. used to cut lumber to length and to cut out notches on Handsaw Crosscut decking and handrails ea. Handsaw Ripping used to rip decking and mudsill boards ea. Keyhole Saw used to cut out notches on decking ea. Coping Saw used to cut out notches on decking ea. used to cut jagged line along bottom of concrete sill Electric Jig Saw forms and cut out notches on decking ea. used to drill holes in corners of notches to allow saw to 3/4" Speed Bore Drill Bit cut out notches ea. used to break out wood between saw cuts on railing Beveled Hatchet notches ea. used to break out wood between saw cuts and shape Wood Chisel 1" bottom of railing notches ea. used to break out wood between saw cuts and shape Wood Chisel 1 1/2" bottom of railing notches ea. used to break out wood between saw cuts and shape Wood Chisel 2" bottom of railing notches ea. used to shape the bottom and sides of the notches Rasp, Surform Flat Bottom and smooth railing surfaces ea. Rasp Blades replacement blades for surform rasp ea. Drawknife 9" Straight Blade used to hewn posts and railings ea. Chainsaw With Log Wizard Attachment used to hewn posts and railings ea. used with sand paper to smooth surface of posts and Sanding Block railing ea. used with sanding block to smooth surface of posts Sandpaper 80 Grit and railing sheet Cloth Tool/Nail Apron used to hold tools and fasteners ea. Leather Tool/Nail Belt used to hold tools and fasteners ea. used to monitor how level and plumb bridge structural Carpenter's Level 4' members are ea. used to monitor how level and plumb bridge structural Smart Level members are ea. used to rake up wood shavings and debris on and Leaf Rake around structure ea. used to sweep up saw dust and wood shavings on Push Broom 24" Heavy Bristle deck ea. used to pick up saw dust and debris swept from Dust Pan decking ea. Plastic Lawn and Leaf Bags used to collect and store sawdust, wood shavings and Extra Strong 39 Gal. debris box Job Security Box used to secure and store tools at job site ea. Bridge Scaffolding Tool/Equipment Function/Use No. Unit (4) 8' x 6" x 3/4" AB Marine used to support 11/2 OD schedule 80 , Type 304SS Grade Plywood Uprights pipe and ea. (4) 6" x 6" x 3/4" AB Marine used to prevent the pipe riding on top of the stringers Grade Plywood Washers from sliding off the stringers ea. used to prevent the plywood washer from sliding off of (4) 5/16" x 2 1/2" Linch Pin the pipe riding on top of the stringers ea.

(2) 6' x 1 1/2" OD schedule 80, upper pipe used to support the scaffolding assembly Type 304SS Pipe and roll the scaffolding along the top of the stringers ea. (2) 10' x 1 1/2" OD schedule lower pipe used to support the aluminum scaffold 80, Type 304SS Pipe planks ea. (4) 7' 10" x 19" Aluminum Scaffold Planks used to provide a working platform for trail workers ea.

Wire Rope Sling Stabilizers (4) 1/4" Dia. X 66" Galvanized Aircraft Cable, 2,800 lb. Nominal Breaking Strength, Pressed Eyes With Thimbles Measured Eye To Eye used to stabilize and support the lower pipe ea. (8) 3/8" x 2 1/2" Shoulder Eye used to attach turnbuckle and proof coil chain to the Bolt top of the plywood upright ea. used between the shoulder eye bolts and the plywood (16) 3/8" Timber Washers uprights ea. used to secure and tighten the shoulder bolts used (4) 1/2" Nuts with the proof coil chain ea. used to secure and tighten the shoulder bolts used (4) 1/2" Wing Nuts with the turnbuckles ea. attaches to wire rope sling stabilizer and shoulder eye bolt and attaches to proof coil chain and eye bolt, (6) 1/2" x 9" Jaw And Jaw adjusts the sling's and chain's length to increase or Turnbuckle decrease tension ea. attaches wire rope sling stabilizer to the end of the (4) 5/16" x 2 1/2" Snap Link lower 1 1/2" pipe ea. (2) Proof Coil Chains 1 3/4" x attaches to the opposing upright plywood post and 1/4" x 24" prevents them from spreading apart ea. used to tighten bolts and nuts used to assemble Adjustable Wrench 10" scaffolding components ea. Combination Wrench Set 5/16"- used to tighten bolts and nuts used to assemble 1 1/2" scaffolding components ea.

Hammer 20 oz. Rip Claw used to drive 16d duplex nails into plywood uprights ea. fastens plywood uprights to wooden bridge stringers to (8) 16d Duplex Nails prevent them from swaying ea. fastens plywood uprights to metal bridge stringers to (4) 24" Bar Clamps prevent them from swaying ea. Crowbar 2' used to pull duplex nails ea. Rope Nylon 1/2" x 20' used to lower scaffold planking onto lower pipe ea. worn by trial workers while assembling bridge and Full Arrest Body Harness anchored to skyline ea. Arbor-Plex Climbing Rope 1/2" tied to body harness to and skyline to secure trail x 30' worker ea. used to secure arbor-plex rope to skyline and slide Carabiner Locking rope along skyline ea. Pipe Bridge Tool/Equipment Function/Use No. Unit used to layout deck beams, braces, decking and 25' Tape Measure anchor brackets ea. used to layout and scribe deck beams, braces, Framing Square decking and anchor brackets ea. used to layout and scribe deck beams, braces, Combination Square decking and anchor brackets ea. used to layout and scribe deck beams, braces, Speed Square decking and anchor brackets ea. used to scribe lines for deck beams, braces, decking Carpenter's Pencil and anchor brackets ea. used to support lumber while performing layout, cutting Saw Horse and drilling ea. used to cut deck beams, braces and decking to Cordless Circular Saw 7 1/4" prescribed lengths ea. Extra Battery Packs charged battery packs for circular saw ea. used to cut deck beams, braces and decking to Circular Saw 7 1/4" Electric prescribed lengths ea. Circular Saw 7 1/4" Combination Saw Blades saw blades for cross cut and ripping ea. used to drill holes through deck beams, braces and Carpenter's Brace Drill pilot holes through decking ea. Drill Brace Bit Set 1/4"-1", 9 used with brace to drill holes through deck beams, 1/2" long braces and pilot holes through decking set

used to drill holes through deck beams, braces and Cordless Drill 1/2" pilot holes through decking and drive deck screws ea. Battery Pack used as additional power source for cordless drill ea.

used to drill holes through deck beams, braces and Gas Powered Drill 1/2" pilot holes through decking and drive deck screws ea. Dolmar gas container for 1/2" drill ea.

used to drill holes through deck beams, braces and Electric Drill 1/2" pilot holes through decking and drive deck screws ea. Generator 2,500 Watt used to power electric circular saw and drill ea. Power Cord 50' With GFI Water Proof Receptacle used to supply power to electric saw and drill ea.

7/16" x 6" Wood Twist Drill Bit used to drill holes for 1/2" lag screws ea.

9/16" x 6" Wood Twist Drill Bit used to drill holes for 1/2" hex head bolts ea. 11/16" x 6" High Speed Steel Drill Bit used to drill holes for 5/8" shackle pin in anchor pipe ea. Chalk Liner used to mark the center of deck beams ea. Bottle of Chalk used to refill chalk line ea.

1/8" x 6" Wood Twist Drill Bit used to drill pilot holes for 5" deck screws ea.

3/16" x 6" Wood Twist Drill Bit used to drill pilot holes for 40d nails ea. Hammer 20 oz. Rip Claw used to drive 40d nails into decking ea. Drift Pin Straight 1/4" Point used to set nail heads on 40d nails ea.

Wood Screw Driver Bit used with drills to drive 5" decking screws into decking ea. used to tighten bolts and nuts used to assemble pipe Ratchet 1/2" Drive bridge components ea. Extension 1/2" Drive 4" used with ratchet ea. Deep Well Socket Set 5/16"-1 used with ratchet to tighten bolts and nuts used to 1/2" assemble pipe bridge components ea. Combination Wrench Set 5/16"- used to tighten bolts and nuts used to assemble pipe 1 1/2" bridge components ea.

Stringer Cart used to transport 8' pipe bridge sections to bridge site ea. used to pound 1 1/2" diameter pipe (support post into Post Driver stream bed ea. used to pound 1 1/2" diameter pipe (support post and Double Jack 10 lb. anchor post) into stream bed ea. used to cut off top of 1 1/2" diameter support post pipes when they are mushroomed from being pounded Hacksaw on ea. used with hacksaw to cut off top of 1 1/2" diameter support post pipes when they are mushroomed from Metal Cut Hacksaw Blades being pounded on ea. used to cut off top of 1 1/2" diameter support post pipes when they are mushroomed from being pounded Reciprocating Saw on ea. used with reciprocating saw to cut off top of 1 1/2" diameter support post pipes when they are Steel Cutting Saw Blade mushroomed from being pounded on ea. used to cut off top of 1 1/2" diameter support post pipes when they are mushroomed from being pounded Pipe Cutter on ea. used to lubricate pipe threads on 2" pipe and 3/4" x 2" Pipe Dope tee can used to thread 3/4" x 2" bull nose galvanized tee onto Aluminum Pipe Wrench 12" 2" dia. pipe (railing post). ea. used to thread 3/4" pvc male adapters into bull nose 12" Adjustable Wrench galvanized tees ea. Shackle, bell shaped screw pin, 5/8" pin, 3.5 ton WLL used to attach turnbuckle to anchor pipe ea. Wire Rope Clips 3/8" used to fasten 3/8" vinyl coated wire to turnbuckle ea. attached to pipe anchor and 3/8" vinyl coated aircraft 1/2" x 12" Jaw And Jaw cable (handrail) and used to tighten vinyl cable to Turnbuckle desired tension ea. Project: Trail Steps Wood & Plastic Wood Steps Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout step carriage overall rise and run, step Level rise and tread and landing depths ea. used with clinometer or abney hand level to layout step carriages, rise and run, step rise and tread and landing depths, also used to measure and layout step 25' Tape Measure drill holes, and notches ea. used to identify elevation stations, end of ledger board locations and center of curved step locations when Pin Flags laying out step carriages ea. used to establish starting and ending step centerline Form Stakes locations for curved step carriages ea. used to turn form stakes to line up the holes in the 12" Aluminum Pipe Wrench stakes ea. Ledger Board 4" x 6" x 5' used to layout curved step carriages ea.

10" spikes used with ledger board to layout curved step carriages ea. used with form stakes to identify the centerline when String Line laying out curved step carriages roll

used with string line to layout curved steps also used Framing Square to layout step notches and cutout stringer stairway ea. used with 25' tape measure to mark the center string Felt Tip Marker line when laying out curved step carriages ea. used to rake organics off the structure footprint and McLeod shape the step footing ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the step Hazel Hoe footing ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea.

used to excavate loamy soils and cast excavated soil off the footing and load soil into wheelbarrow or toter Round Point Shovel and load and offload aggregate used for step tread ea. used to excavated and shape the bottom of the footing or load soil into wheelbarrow or toter and load and off Square Point Shovel load aggregate used for step tread ea. used to dig out smaller rocks protruding into the step Pinch Point Crow Bar 60" footing ea.

used to drive form stakes into the ground, break or smash rocks protruding into the step footing and drive Double Jack 10 lb. 5/8" rebar through wood and plastic wood steps ea. used to cut off rebar if rocky soil prohibits driving it to Hacksaw full depth ea. used with hacksaw to cut off rebar if rocky soil Metal Cut Hacksaw Blades prohibits driving it to full depth ea. Stringer Cart used to transport lumber to structure site ea. Trail Cart used to transport lumber to structure site ea. used to carry tools, and aggregate to worksite or Wheelbarrow transport soil being used for fill material elsewhere ea. used to carry tools, materials, fuel cans, and aggregate to worksite or transport soil being used for Toter 1,500 lb. Capacity fill material elsewhere ea. used to carry tools, materials, fuel cans, and aggregate to worksite or transport soil being used for Toter 2,500 lb. Capacity fill material elsewhere ea. used to carry tools, materials, fuel cans, and aggregate to worksite or transport soil being used for Toter 3,500 lb. Capacity fill material elsewhere ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea.

Tamper 10" x10", 15 lb. used to compact step footings and aggregate backfill ea. 5 Gallon Fuel Can gas container for toters ea.

Carpenter's Brace Drill used to drill pilot holes for 5/8" rebar 60d and 40d nails ea. Drill Brace Bit Set 1/4"-1", 9 used with carpenter's brace to drill pilot holes for 5/8" 1/2" long rebar and 60d nails set

Gas Powered 1/2" Drill used to drill pilot holes for 5/8" rebar 60d and 40d nails ea. Dolmar gas container for chainsaw and 1/2" drill ea. Generator 2,500 Watt used to power electric drill and circular saw ea. Power Cord 50' With GFI Water Proof Receptacle used to supply power to electric drill and circular saw ea.

Electric Drill 1/2" used to drill pilot holes for 5/8" rebar 60d and 40d nails ea. used to drill pilot holes for 40d nails used on cutout 3/16" x 6" Wood Twist Drill Bit stringer stairways ea. used to drill pilot holes for 60d nails used on cutout 7/32" x 6" Wood Twist Drill Bit stringer stairways ea.

Ship Auger Drill Bit 11/32" x used to drill pilot hole for 3/8" x 10" spikes used to pin 18" the top step on an interlocking cribbed step carriage ea.

Ship Auger Drill Bit 1/2" x 18". used to drill hole for 3/8" wire rope used in cable steps ea. used to drill pilot hole for 5/8" rebar used to pin wood Ship Auger Drill Bit 9/16" x 18" and plastic wood steps ea. used to cut wood and plastic step material to the prescribed lengths, cut notches in interlocking steps Handsaw Crosscut and cut out the steps on the cutout stringer. ea. Handsaw Ripping used to cut notches in interlocking steps ea. used to cut wood and plastic step material to the prescribed lengths, cut notches in interlocking steps Cordless Circular Saw 7 1/4" and cut out the steps on the cutout stringer. ea. Extra Battery Packs charged battery packs for circular saw ea. used to cut wood and plastic step material to the prescribed lengths, cut notches in interlocking steps Circular Saw 7 1/4" Electric and cut out the steps on the cutout stringer. ea. Circular Saw 7 1/4" Combination Saw Blades saw blades for cross cut and ripping ea. used to support lumber while performing layout, cutting Saw Horse and notching ea.

Table Saw 10" 3 HP used to cut octagon shaped steps for cable steps ea. used to treat sawn cuts and holes in pressure treated 1 Gallon Of Wood Preservative wood gal. used to contain wood preservative while it is being Plastic Pale 1/2 Gal. applied to pressure treated wood. ea. Paint Brush used to apply wood preservative (cut ends) ea. Bottle Brush used to apply wood preservative (holes) ea. used to protect hands while applying wood Rubber Gloves preservative pair used to break out wood between saw cuts on step Beveled Hatchet notches ea. used to break out wood between saw cuts and shape Wood Chisel 1" bottom of step notches ea. used to break out wood between saw cuts and shape Wood Chisel 1 1/2" bottom of step notches ea. used to break out wood between saw cuts and shape Wood Chisel 2" bottom of step notches ea. Rasp, Surform Flat Bottom used to shape the bottom and sides of notches ea. Rasp Blades replacement blades for surform rasp ea. Hammer 20 oz. Rip Claw used to drive 40d nails into decking ea. Hand Sledge 2lb. used to drive 60d nails into decking ea. Drift Pin Straight 1/4" Point used to set nail heads on 40d nails ea. Drift Pin Straight 3/8" Point used to set nail heads on 60d nails ea.

Wood Screw Driver Bit used with drills to drive 6" decking screws into decking ea. Ratchet 1/2" Drive used to tighten nuts on cable step wire rope clips ea. Deep Well Socket Set 5/16"-1 used with ratchet to tighten nuts on cable step wire 1/2" rope clips ea. Cloth Tool/Nail Apron used to hold tools and fasteners ea. Leather Tool/Nail Belt used to hold tools and fasteners ea. used to monitor the prescribed front to back and side Carpenter's Level 4' to side slope of the steps ea. used to monitor the prescribed front to back and side Smart Level to side slope of the steps ea. Rock Steps Tool/Equipment Function/Use No. Unit Clinometer or Abney Hand used to layout step carriage overall rise and run, step Level rise and tread and landing depths ea. used with clinometer or abney hand level to layout step carriages, overall rise and run, step rise and tread 25' Tape Measure and landing depths ea. Pin Flags used to identify elevation stations ea. used to rake organics off the structure footprint and McLeod shape the step footing ea. Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate loamy soils and shape the step Hazel Hoe footing ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea.

used to excavate loamy soils and cast excavated soil off the footing, load soil into wheelbarrow or toter and Round Point Shovel load and offload aggregate used for step tread ea. used to excavated and shape the bottom of the footing, load soil into wheelbarrow or toter and load Square Point Shovel and off load aggregate used for step tread ea. used to break or smash rocks protruding into the Double Jack 10 lb. footing and making crush fill ea. used to break or smash rocks protruding into the Single Jack 4lb. footing and making crush fill ea. used to dig out smaller rocks protruding into the footing, move larger rocks into position and lever rocks Pinch Point Crow Bar 60" together ea. Tamper 10" x10", 15 lb. used to compact loose soils in footing ea. used to carry stones and crush fill to worksite or to Rock Litter location where they are placed in the structure. ea.

used to carry tools, stones and crush fill to worksite or Wheelbarrow transport soil being used for fill material elsewhere ea. used to carry tools, materials, fuel cans, stones and crush fill to worksite or transport soil being used for fill Toter 1,500 lb. Capacity material elsewhere ea. used to carry tools, materials, fuel cans, stones and crush fill to worksite or transport soil being used for fill Toter 2,500 lb. Capacity material elsewhere ea. used to carry tools, materials, fuel cans, stones and crush fill to worksite or transport soil being used for fill Toter 3,500 lb. Capacity material elsewhere ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Can gas container for toters ea.

Rigging Equipment Used to See Rigging Operations (Highleads and Skylines, Construct Rock Steps Transverse Anchors and Highleads off of Skylines used to measure stones for sorting, breaking and Tape Measure 25' shaping ea.

Chalk used to mark stones for sorting, breaking and shaping ea. Feathers and Wedges 1 1/4" x 8" steel wedges to drive in drill holes to split rocks set Bosche Rotary Hammer used to drill holes in rocks for plugs and feathers ea. Generator 2,500 Watt used to power bosch rotary hammer ea. used with rotary hammer to drill holes in rocks for the SDS Max 1/2" Bit purpose of splitting and shaping rock ea. used with rotary hammer to drill holes in rocks for the SDS Max 1 1/4" Bit purpose of splitting and shaping rock ea.

Feathers and Wedges 1/2" x 4" steel wedges to drive in drill holes to split rocks set Striking Hammer 8lb. used to strike slab and rifting hammers ea. Slab Hammer 8lb. used to split and shape rock ea. Rifting Hammer 8lb. used to split and shape rock ea. Cutter's Hammer used to strike steel rock shaping tools ea.

Hand Tracer Carbide 11/8"x3" used to score stone where it is to be broken ea. Hand Point Carbide 1" used to take off high points on stone ea. used to take off high points on stone, remove small Hand Chisel Carbide 1" ledges or score lines ea. used to remove material parallel to a flat stone or to Hand Set Carbide 11/8" x 3" remove drill marks ea. Hammer Point Carbide 3lb. used to remove high points and shape stone ea. Spalling Hammer 4lb. used to break and shape rock ea. Cross Pien Hammer used to break and shape rock ea. Mason (Mash) Hammer 6lb. used to break and crush rock for fill ea. Crowbar 18" used to maneuver and position rocks ea. used to monitor the prescribed front to back and side Carpenter's Level 4' to side slope of the steps ea. used to monitor the prescribed front to back and side Smart Level to side slope of the steps ea. Project: Railings Wooden Railings Tool/Equipment Function/Use No. Unit Pick Mattock used to excavate rocky or consolidated soils ea. Cutter Mattock used to excavate consolidated soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. used to excavate soft loamy soils or remove soil and rocks loosened by other excavation tools and place soil next to post hole or footing for use as backfill or Round Point Shovel load soil into wheelbarrow or toter ea. used to dig out smaller rocks or hard soil in the post Pinch Point Crow Bar 60" hole or footing ea. used to dig out smaller rocks or hard soil in the post hole or footing and tamp and compact soil backfilled Digging Bar 60" around post or post sill ea.

used to dig post hole in soft loamy soils or remove soil Post Hole Digger and rocks loosened by other excavation tools ea.

used in post sill footings to remove soil and rocks loosened by other excavation tools, shape the bottom of the footing and place soil next to footing for use as Square Point Shovel backfill or load soil into wheelbarrow or toter ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. Double Jack 10 lb. used to drive 5/8" rebar through post sill ea. used to cut off rebar if rocky soil prohibits driving it to Hacksaw full depth ea. used with hacksaw to cut off rebar if rocky soil Metal Cut Hacksaw Blades prohibits driving it to full depth ea. Tamper 10" x10", 15 lb. used to compact post sill footing ea.

Viberplate Compactor 180 lb. used to compact backfill over post sill ea. Dolmar gas container for viberplate compactor ea.

Trail Cart used to transport post and railing materials to worksite ea. used to carry tools, fuel and materials to worksite, transport excess foundation soil to sites needing fill Wheelbarrow material and mix concrete ea.

used to carry tools, aggregate and materials to worksite, transport fuel cans, and transport excess Toter 1,500 lb. Capacity foundation soil to sites needing fill material ea.

used to carry tools, aggregate and materials to worksite, transport fuel cans, and transport excess Toter 2,500 lb. Capacity foundation soil to sites needing fill material ea.

used to carry tools, aggregate and materials to worksite, transport fuel cans, and transport excess Toter 3,500 lb. Capacity foundation soil to sites needing fill material ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Can gas container for toters ea. used to layout post sill, post brace, post, railing and 25' Tape Measure soil dam cuts and notching ea. used to scribe lines for post sill, post brace, post, Carpenter's Pencil railing and soil dam cuts and notching ea. used to layout and scribe lines for post sill, post brace, Framing Square post, railing and soil dam cuts and notching ea.

used to layout and scribe lines for post sill, post brace, Combination square post, railing and soil dam cuts and notching ea.

used to layout and scribe lines for post sill, post brace, Speed Square post, railing and soil dam cuts and notching ea. used to identify the angle of the cut on top of the post String Line on a sloping grade. roll used to treat sawn cuts and holes in pressure treated 1 Gallon Of Wood Preservative wood post sills gal. used to contain wood preservative while it is being Plastic Pale 1/2 Gal. applied to pressure treated wood post sills. ea. Paint Brush used to apply wood preservative (cut ends) ea. Bottle Brush used to apply wood preservative (holes) ea. used to protect hands while applying wood Rubber Gloves preservative pair

ATV With Trailer/Water Tank used to supply water to mix with concrete ea. Water Bucket 5 Gal. used to supply water to mix with concrete ea. container used to mix concrete and water used in post Concrete Mixing Tub hole ea. Concrete Mixing Hoe tool used to mix concrete and water ea. used to level and shape concrete around steel post Brick Trowel brackets ea. used to cut post sills, soil dams, post braces, post and Handsaw Crosscut railing to length and notches on railing ea. Generator 2,500 Watt used to power electric circular saw and drill ea. Power Cord 50' With GFI Water Proof Receptacle used to supply power to electric saw and drill ea. used to cut post sills, soil dams, post braces, post and Cordless Circular Saw 7 1/4" railing to length and notches on railing ea. Extra Battery Packs charged battery packs for circular saw ea. used to cut post sills, soil dams, post braces, post and Circular Saw 7 1/4" Electric railing to length and notches on railing ea. Circular Saw 7 1/4" Combination Saw Blades extra saw blades ea. used to support lumber while performing layout, cutting Saw Horse and ripping ea. Beveled Hatchet used to break out wood between saw cuts on notches ea. used to break out wood between saw cuts and shape Wood Chisel 1" bottom of notches ea. used to break out wood between saw cuts and shape Wood Chisel 1 1/2" bottom of notches ea. used to break out wood between saw cuts and shape Wood Chisel 2" bottom of notches ea. used to shape the bottom and sides of the notches Rasp, Surform Flat Bottom and smooth railing surfaces ea. Rasp Blades replacement blades for surform rasp ea. used to drill holes through posts, also drill pilot holes through post sills, soil dams, post braces, posts and Carpenter's Brace Drill railing ea. used with carpenter's brace to drill holes through Drill Brace Bit Set 1/4"-1", 9 posts, also drill pilot holes through post sills, soil dams, 1/2" long post braces, posts and railing set used to drill holes through posts, also drill pilot holes through post sills, soil dams, post braces, posts and Cordless Drill 1/2" railing ea. Battery Pack used as additional power source for cordless drill ea. used to drill holes through posts, also drill pilot holes through post sills, soil dams, post braces, posts and Gas Powered Drill 1/2" railing ea. Dolmar gas container for 1/2" drill ea. used to drill holes through posts, also drill pilot holes through post sills, soil dams, post braces, posts and Electric Drill 1/2" railing ea. Auger Drill Bit 9/16" x 18" used to drill hole for 5/8" rebar through post sills ea.

5/32" x 6" Wood Twist Drill Bit used to drill pilot holes for 30d nails ea.

3/16" x 6" Wood Twist Drill Bit used to drill pilot holes for 40d nails ea. used to drill holes for 5/8" hex head bolts anchoring 5/8" x 6" Wood Twist Drill Bit post to steel post brackets ea. used to tighten bolts and nuts used on steel post Ratchet 1/2" Drive anchors ea. Deep Well Socket Set 5/16"-1 used with ratchet to tighten bolts and nuts used on 1/2" steel post anchors ea. Combination Wrench Set 5/16"- used to tighten bolts and nuts used on steel post 1 1/2" anchors ea. used to drive 30d nails into post braces and post and Hammer 20 oz. Rip Claw 40d nails into soil dams and railings ea. Drift Pin Straight 1/4" Point used to set nail heads on 30d and 40d nails ea. Crowbar 2' used to pull nails ea. Carpenter's Level 2' used to monitor how plumb post are ea. Drawknife 9" Straight Blade used to hewn posts and railings ea. Chainsaw With Log Wizard Attachment used to hewn posts and railings ea. used with sand paper to smooth surface of posts and Sanding Block railing ea. used with sanding block to smooth surface of posts Sandpaper 80 Grit and railing sheet Cloth Tool/Nail Apron used to hold tools and fasteners ea. Leather Tool/Nail Belt used to hold tools and fasteners ea. Refer to Single and Multi Tier Rock Retaining Rock Masonry Railings Walls (dry stone and wet masonry) Project: Administrative Spike Camps Camp Facilities Tool/Equipment Function/Use No. Unit

Aluminum Tent Frame 12' x 14' used to support canvas wall tent ea.

Tent Frame Carry Bag used to contain tent frame when storing or transporting ea. 1/2" Double Braided Polyester Rope, 200' hung from trees and used to support roof of wall tent ea. used to support and anchor corners and sides of wall Metal T Post 6' tent when using rope to support roof ea.

12 Oz. Canvas Wall Tent 12' x used for cook kitchen and food and kitchen supplies 14' With Screened Window storage ea.

Wall Tent Carry Bag used to contain wall tent when storing or transporting ea. 12 Oz. Canvas Wall Tent 12' x 14' With Stove Jack and Screened Window used for community tent ea. 12" Metal Tent Stakes (20 Pack) used to stake down wall tent and rain fly pack used to contain tent stakes when storing or Tent Stake Carry Bag transporting ea. 1/4" Black Poly Rope (200') Coil used with tent stakes to tie down wall tent and rain fly coil Tent Rope Tensioners used to tighten black poly rope doz. Wall Tent Rain Flys (Relite) used to shed rain from wall tent roof ea. used to contain rain fly, tensioners and poly rope when Rain Fly/Rope Carry Bag storing or transporting ea. Wood Stove 13" x 13" x 22" used to heat community tent ea. Nesting Stove Pipe 4" to 5", Five Piece Set used with wood stove to carry smoke out of tent set used with wood stove to reduce sparks exiting stove Spark Arrestor For 4" Pipe pipe ea. hung over camp and used to provide shade and rain Rain Fly protection ea. used to anchor corners of rain fly to trees, wall tent 1/2" Double Braided Polyester frames, or ground anchors, also used to secure toilet Rope, 400' and shower tarps coil Chemical Toilet used for frontcountry spike camp toilet facility ea. Toilet Tent With Frame, 3' x 5'Interior, 6' Wall Height, 7'6" Ridge Height and Screened Gable Ends used to provide privacy for camp toilet ea. Tarp, Heavy Duty 16 Mil. Poly, 6' x 18' used to provide privacy for camp privy ea. Toilet Seat, Wood used with camp privy ea. Toilet Tent With Frame, 3' x 5'Interior, 6' Wall Height, 7'6" Ridge Height and Screened Gable Ends used to provide privacy for camp shower ea. Shower Trailer used for frontcountry spike camp shower facility ea. Solar Shower Bag, 5 Gal. used to provide hot water for showering ea. Tarp, Heavy Duty 16 Mil. Poly, 6' x 18' used to provide privacy for camp shower ea. Tent, Three Season, Two used by individual trail crew worker for sleeping Person Size Min. quarters ea. Tent Ground Cloth, Coated Polyester, 87" x 50" Min. used to protect tent floor and provide moister barrier ea. Sleeping Pad, 25" x 77" x 3" Min. used to provide sleeping comfort and insulation ea. Sleeping Bag, Synthetic Fill, 20 Degree Rating used by trail workers to sleep in ea. Bear Resistant Locker, 30 Cu. used in frontcountry spike camps to keep bears out of Ft. Capacity, 48" x 37" food supplies ea. Bear Resistant Trash Can, used in frontcountry spike camps to keep bears out of Double 140 gallon Capacity garbage ea. Bear Resistant Food Canisters, Carbon Fiber, 900 Cu. In. used in backcountry spike camps to keep bears out of Capacity food supplies ea.

Bear Resistant Food Hanging Rope 100' 1/2" Double Braided used in backcountry spike camps, tied between two Polyester Rope trees 20'-25' off the ground ea. used in backcountry spike camps, with bear hanging rope, attached to rope via shackle and used to lift food 4 1/2" Block With Shackle supplies off the ground. ea. used in backcountry spike camps, ran through 4 1/2" Bear Resistant Food Hanging block and tied to food supplies, either tied to a single Rope 50' 1/2" Double Braided load and then tied off to a nearby tree or tied off to two Polyester Rope loads counterbalancing each other ea.

Cargo Net, Heavy Duty, 5' x 7' used in backcountry spike camps with food hanging Min. With Storage Bag rope to contain food storage canisters or bags. ea. Carabiner, Locking used to tie cargo net together ea. Heavy Duty Campfire Grill 18" x 24" x 12" Height Min. used to support hot water (jungle) can ea.

Igloo Beverage Cooler 5 Gal. used to store cool drinking water and beverages ea. Commercial 160 Quart Stainless Steel Brewing Kettle used to provide hot water for washing hands, dishes (Jungle Can) and showering ea. Propane Lanterns, Double used in frontcountry spike camps to provide light in Mantle kitchen and common areas ea. Propane Lantern, Carrying Case used to protect lantern during transport ea.

Propane Outlet Distribution used in frontcountry spike camps with propane lantern Post to provide light in kitchen and common areas ea. attached to propane outlet post to supply fuel to Propane Tank 5 Ga. lantern ea. Fueled Lantern, Duel Fuel, used in backcountry spike camps to provide light in Double Mantle kitchen and common areas ea.

Fueled Lantern, Carrying Case used to protect lantern during transport ea.

Fueled Lantern Mantles spare mantles used with propane and fueled lanterns pack. 1/4" Wire Mesh Screen 2.5' x 5' on 2" x 4" Wood Frame place on top of gray water sump to catch silverware ea. Inline Water Filters, Min. 5 Micron used to provide potable to spike camp ea. Water Filter Stand Wood used to hold water filters ea. 1" Fire Hose used to supply water to filters feet Sandbags Heavy Duty With Tie used to anchor 1" fire hose inlet when siphoning String, 14.5" x 26" stream water to feed filters ea. Bag Filter 10 Liter Min. used to provide potable to spike camp ea. Dromatory Bag 10 Liter Min. used to store and distribute filtered water ea.

Folding Aluminum Camp Table 55" x 28' x 28" Assembled, 55" x 6.5' x 4.5" Disassembled used for food prep in kitchen and for dining ea. Camp Table Carrying Case used for storing and transporting camp table ea. Camp Stool 15" W x 16" D x used by trail crew for sitting at camp table or relaxing 17.5" H around camp ea. Camp Stool Carrying Case used for storing and transporting camp stool ea. Picnic Table 8' Wood used in frontcountry spike camps for dining ea. Kitchen Items Tool/Equipment Function/Use No. Unit

Ice Chest 2.5 Cu. Ft. With Bear Prevention Locking Capacity used to store perishable food ea.

Ice Chest 3.3 Cu. Ft. With Bear Prevention Locking Capacity used to store perishable food ea. Bear Prevention Ice Chest Locks used to lock the lid on ice chest ea.

Propane Camp Stove, 3 Burner, 30,000 BTU Per Burner, With Detachable legs used as stove top for cooking meals ea. Propane Camp Stove Carrying Case used to protect stove during transport ea.

Propane Camp Oven, 24"L x 18"W x 16"H Min., 6,000 BTU Burners, 3,000 BTU Oven used as oven and stove top for cooking meals ea. Oven Stand, Collapsible used to support oven ea. used in front country spike camps to supply propane to Propane Tank 25 Ga. stove and oven ea. Propane Tank 5 Ga. used to supply propane to stove and oven ea.

Liquid Fuel Stove, Two Burner, 14,000 BTU Per Burner used as stove top for cooking meals ea. Stove Stand, Collapsible used to support stove ea. Cast Iron Dutch Oven 12", 6 Quart used as oven for cooking meals ea. Cast Iron Dutch Oven 12", 6 Quart Tote Bag used to protect oven during transport ea. Cast Iron Dutch Oven Deep 12", 8 Quart used as oven for cooking meals ea. Cast Iron Dutch Oven Deep 12", 8 Quart Tote Bag used to protect oven during transport ea. Cast Iron Dutch Oven 14", 8 Quart used as oven for cooking meals ea. Cast Iron Dutch Oven 14", 8 Quart Tote Bag used to protect oven during transport ea. Cast Iron Dutch Oven Deep 14", 10 Quart used as oven for cooking meals ea. Cast Iron Dutch Oven Deep 14", 10 Quart Tote Bag used to protect oven during transport ea. Cast Iron Dutch Oven Deep 16", 12 Quart used as oven for cooking meals ea. Cast Iron Dutch Oven Deep 16", 12 Quart Tote Bag used to protect oven during transport ea. Charcoal Chimney Starter used to ignite charcoal used to heat dutch ovens ea. Dutch Oven Lid Lifter used to lift lids off of dutch ovens when in used ea. used to support dutch oven lid on ground when Dutch Oven Lid Stand checking contents of oven or serving out of oven ea. used to pick up and place charcoal while heating dutch 16" Tongs oven ea. used for cooking on top of propane and liquid fuel Cast Iron Griddle 20" x 10.5" burners ea. Cast Iron Skillet Deep 12" With used for cooking on top of propane and liquid fuel Lid burners ea. used for cooking on top of propane and liquid fuel Cast Iron Skillet 12" burners ea. used for cooking on top of propane and liquid fuel Cast Iron Skillet 15" burners ea. used for cooking on top of propane and liquid fuel Cast Iron Skillet 17" burners ea. Stainless Steel 10 Quart used for cooking on top of propane and liquid fuel Brazier Pan With Cover burners ea. Stainless Steel 8 Quart Stock used for cooking on top of propane and liquid fuel Pot With Cover burners ea. Stainless Steel 6 Quart Stock used for cooking on top of propane and liquid fuel Pot With Cover burners ea. Stainless Steel 4 Quart Sauce used for cooking on top of propane and liquid fuel Pan With Cover burners ea. Stainless Steel 2.75 Quart used for cooking on top of propane and liquid fuel Sauce Pan With Cover burners ea. Round Cake Pan 10" x 2" used to bake cakes ea.

Square Baking Pan 9" x 9" x 2" used for baking ea. Rectangular Baking Pan 13" x 9" x 2" used for baking ea. Loaf Pan 9 1/4" x 5 1/4" x 2 1/2" used for baking ea.

Deep Dish Pie Pan 9 1/2" x 2" used to bake pies ea. Cookie Sheet 9" x 13" used for baking ea. Round Pizza Pan 12" used for baking pizzas ea. Stainless Steel Mixing Bowl 3 Quart used for mixing and serving ea. Stainless Steel Mixing Bowl 4 Quart used for mixing and serving ea. Stainless Steel Mixing Bowl 5 Quart used for mixing and serving ea. Stainless Steel Mixing Bowl 13 Quart used for mixing and serving ea. Stainless Steel Colander 5 Quart used for straining pasta and vegetables ea. Stainless Steel Manual Egg Beater used for mixing ea. Wood Spoon 14" used for mixing and stirring ea. Wood Spoon 18" used for mixing and stirring ea. Stainless Steel Tongs 9" used for handling food while cooking ea. Stainless Steel Slotted Spoon 13" used for stirring and serving food ea.

Stainless Steel Ladle 13 3/4"" used for serving food ea. Silicone Square Turner 11" used for turning food over in cooking pans ea. Silicone Round Turner 11" used for turning food over in cooking pans ea. Stainless Steel Square Turner 18" used for turning food over on grill ea. Can Opener Manual used to open can goods ea. Silicone Spatula 11 3/4" used to mix and stir baking mixes ea. Stainless Steel Swivel Peeler 7" used to peel fruit and vegetables ea. Stainless Steel Grater 10" used to grate vegetables and cheese ea. Stainless Steel Balloon Wisk 11" used to mix and stir baking mixes and eggs ea. Stainless Steel Potato Masher 10" used to mash potatoes, squash, pumpkin, etc. ea. Pizza Wheel 9" used to cut pizzas ea.

Cutting Board 13' x 10" x 1/32" surface for cutting vegetables, fruit, meat, etc. ea. Stainless Steen Nesting Measuring Cups used to measure food ingredients set Stainless Steen Nesting Measuring Spoons used to measure slice and baking ingredients set Salt Shaker used to apply salt to food ea. Pepper Shaker used to apply pepper to food ea. Paring Knife 4" used to cut and peel vegetables and fruit ea. Boning Knife 6" used to cut up vegetables, fruit and meat ea. used to cut up vegetables, fruit and meat and carve Chef's Knife 8" meat ea. Bread Knife 9" used to slice bread ea. Poly Carbonate Food Trey used to hold plate, bowl, cups and utensils doz. Poly Carbonate Dinner Plate used to eat off of doz. Poly Carbonate Bowl used to eat off of doz.

Poly Carbonate Drinking Glass used to drink from doz. Poly Carbonate Coffee Mug used to drink from doz. Stainless Steel Knife, Fork Spoon Set used to eat with ea. Steak Knife used to cut meat ea. Commercial 4 hole Stainless Steel Cylinder Flatware Utensil Holder used to store flatware and steak knives ea. used to grasp and carry hot pots, pans and cast iron Oven Mits cookware Scrub Sponge Non Scratch 4 1/2" x 3" used for washing pots, pans and dishes ea.

Kitchen Wash Cloths 13" x 13" used to wash dishes and clean kitchen appliances ea. Kitchen Towels 18" x 26" used to dry dishes and hands at wash station ea. used to wash and rinse dishes and as a hand washing Polyethylene Tub 20" x 15" x 5" station ea. See retaining structure, drainage structure, timber Project: Drainage and planking, puncheon and boardwalk, bridge, step Structure Maintenance and railing construction

Project: Trail Removal and Site Restoration Trail Removal Tool/Equipment Function/Use No. Unit used to rake organics below the trail alignment for later use, excavate loamy soil below outboard hinge, rake soil onto recontoured trail bench and rake organics on top of soil used to recontour the trail McLeod bench ea. used to de-compact the trail bench, excavate the outboard hinge of the trail and pull soil onto de- Pick Mattock compacted trail bench ea. used to de-compact the trail bench, excavate the outboard hinge of the trail and pull soil onto de- Cutter Mattock compacted trail bench ea.

used to excavate loamy soils below the outboard hinge Hazel Hoe and pull that soil onto de-compacted trail bench ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea.

used to excavate loamy soils below the outboard hinge Round Point Shovel and place that soil onto de-compacted trail bench ea. used to dig out or loosen smaller rocks embedded into the trail tread so they can be used to recontour the trail Pinch Point Crow Bar 60" bench ea. used to compact the soil used to recontour the trail Tamper 10" x10", 15 lb. bench ea. Slide Hammer used to de-compact the trail tread ea. used with slide hammer to break apart and loosen Digging Chisel Breaker Bit 12" hard compacted or rocky soils ea. Cobra Pro Gas Powered Breaker used to de-compact the trail tread ea. used with gas powered breaker to break apart and Digging Chisel Breaker Bit 18" loosen hard compacted or rocky soils ea. used with gas powered breaker to break apart and Clay Spade Breaker Bit 14" loosen hard compacted or rocky soils ea. Dolmar breaker gas/two cycle oil mix container ea. Breaker Tool Kit wrenches and screwdrivers to tune and repair ea. used to de-compact the trail bench, excavate the outboard hinge of the trail and pull soil onto de- Mini Excavator, 4' overall width compacted trail bench ea. Excavator Hydraulic Thumb used to grasp and place brush, organics and logs on Attachment top of the recontoured trail bench ea. Tool Box For Dozer, Excavator, tools for servicing and repairing dozer, Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea. used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. 5 Gallon Fuel Cans For Excavator diesel fuel to operate excavator ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans and Toter 1,500 lb. Capacity transport excess soil to soil deficit areas ea. used to carry tools and materials to worksite, transport mini excavator attachments and fuel cans and Toter 2,500 lb. Capacity transport excess soil to soil deficit areas ea. 5 Gallon Fuel Can gas container for toters ea. Site Restoration Tool/Equipment Function/Use No. Unit used to retain soil and reduce surface erosion on trail Straw Wattles 9" x 25' removal and recontour projects ea. Wood Stakes 18" used to pin straw wattles to ground ea. used to retain soil and reduce surface erosion on trail Straw Wattles 12" x 25' removal and recontour projects ea. Wood Stakes 24" used to pin straw wattles to ground ea. Hand Sledge 4lb. used to drive wood stakes into straw wattles ea. Manual Hand Operated Seed used to spread grass seed over recontoured trail Broadcaster areas and exposed soils ea. Bow Rake 16 Tine used to rake grass seed into soil for germination ea.

Burlap Sack With Drawstring, used to store and transport salvaged native plants that 10 oz. 14" x 26" are used to revegetate disturbed areas bundle Clinometer or Abney Hand Level used to layout rock and wood check dams ea. used with clinometer to layout rock and wood check 25' Tape Measure dams and layout wood check dam boards ea. used to rake organics off the entrenched trail where McLeod check dams are to be installed ea. used to excavate check dam footings in rocky or Pick Mattock consolidated soils ea. used to excavate check dam footings in consolidated Cutter Mattock soils and cut roots ea. Pulaski used to excavated loamy soils and cut roots ea. Pitchfork use to spread native mulch and organics ea. used to excavate check dam footings in loamy or Hazel Hoe unconsolidated soils ea. File 10" Mill Bastard With Handle used to sharpen excavation and cutting tools ea. used to transplant native vegetation, excavate and shape the bottom of the soil dam footing, removing soil behind silt fences and loading that soil into Round Point Shovel wheelbarrows or toters ea. used to excavate and shape the bottom of the soil dam footing, removing soil behind silt fences and Square Point Shovel loading that soil into wheelbarrows or toters ea. used to dig out smaller rocks protruding into the soil dam footing, move larger rocks into position and lever Pinch Point Crow Bar 60" rocks together ea. Tamper 10" x10", 15 lb. used to compact loose soils in footing ea.

used to drive wood soil dam stakes into ground and Double Jack 10 lb. break or smash rocks protruding into the footing ea. Trail Cart used to transport lumber and tools to worksite ea. used to carry stones to worksite or to location where Rock Litter they are placed in the structure. ea. used to carry tools or stones to worksite or transport Wheelbarrow soil excavated from behind silt fences ea. used to carry tools or stones to worksite or transport Toter 1,500 lb. Capacity soil excavated from behind silt fences ea. used to carry tools or stones to worksite or transport Toter 2,500 lb. Capacity soil excavated from behind silt fences ea. used to carry tools or stones to worksite or transport Toter 3,500 lb. Capacity soil excavated from behind silt fences ea. Toters and Other Power excavator,toters and other large power equipment Equipment and installing attachments ea.

used to clean up deisel, gas, oil hydraulic oil spills Universal Bag Spill Kit, 10 Gal. realted to dozer, excavator and toter operations ea. 5 Gallon Fuel Can gas container for toters ea.

Chalk used to mark stones for sorting, breaking and shaping ea. Striking Hammer 8lb. used to strike slab and rifting hammers ea. Slab Hammer 8lb. used to split and shape rock ea. Rifting Hammer 8lb. used to split and shape rock ea. Cutter's Hammer used to strike steel rock shaping tools ea.

Hand Tracer Carbide 11/8"x3" used to score stone where it is to be broken ea. Hand Point Carbide 1" used to take off high points on stone ea. used to take off high points on stone, remove small Hand Chisel Carbide 1" ledges or score lines ea. used to remove material parallel to a flat stone or to Hand Set Carbide 11/8" x 3" remove drill marks ea. Hammer Point Carbide 3lb. used to remove high points and shape stone ea. Spalling Hammer 4lb. used to break and shape rock ea. Cross Pien Hammer used to break and shape rock ea. used to layout and scribe saw cuts for wood check Framing Square dams ea. used to layout and scribe saw cuts for wood check Combination Square dams ea. Carpenter's Pencil used to scribe notch lines ea. used to support lumber while performing layout and Saw Horse cutting ea. Hand Saw Crosscut used to cut soil dam boards ea.

Cordless Circular Saw 7 1/4" used to cut soil dam boards ea. Extra Battery Packs charged battery packs for circular saw ea. Circular Saw 7 1/4" Electric used to cut soil dam boards ea. Circular Saw 7 1/4" Saw Blades extra saw blades ea. Generator 2,500 Watt used to power electric circular saw and drill ea. Power Cord 50' With GFI Water Proof Receptacle used to supply power to electric saw and drill ea. used to monitor how level each check dam is when Carpenter's Level 4' installed ea. used to monitor how level each check dam is when Smart Level installed ea. used for drilling pilot nail holes in wood check dam Cordless Drill 1/2" boards ea. Extra Battery Packs charged battery packs for cordless drill ea. used to drill pilot holes for 70d nails used to fasten Drill Bit 1/4" check dam boards ea. Hammer 20 oz. Rip Claw used to drive 70d nails into check dam boards ea. Hand Sledge 2lb. used to drive 70d nails into check dam boards ea. Propane Burner Torch Set With 60" Hose used to ignite project debris burn piles ea. Five Gallon Propane Tank fuel source for burner torch ea. Project: Rigging Operations Direct Pulls and Choker Rolls Used in Clearing Tool/Equipment Function/Use No. Unit 2,000 lb. capacity hoist used to pull small size trees and stobs out of the ground and move small size downed trees out of the trail clearing limits, hoist Griphoist TU 17 includes mainline and handle ea.

4,000 lb. capacity hoist used to pull small to medium size trees and stobs out of the ground and move medium size downed trees out of the trail clearing Griphoist TU 28 limits, hoist includes mainline and handle ea. 8,000 lb. capacity hoist used to pull medium size trees and stobs out of the ground and move large size downed trees out of the trail clearing limits, hoist Griphoist TU 32 includes mainline and handle ea. sockets and ratchet for removing side covers, shear pins for all three hoist, pickle fork, ball peen hammer Griphoist Repair Kit and quart of 90 weight oil ea. Wire Rope Sling 3/8" x 50' used with TU 17 griphoist to pull and move logs ea. Wire Rope Sling 3/8" x 100' used with TU 17 griphoist to pull and move logs ea. Wire Rope Sling 1/2" x 50' used with TU 28 griphoist to pull and move logs ea. Wire Rope Sling 1/2" x 100' used with TU 28 griphoist to pull and move logs ea. Wire Rope Sling 3/4" x 50' used with TU 32 griphoist to pull and move logs ea. Wire Rope Sling 3/4" x 100' used with TU 32 griphoist to pull and move logs ea. Synthetic Rope (amsteel blue) 1/2" x 150' used with TU 17 griphoist to pull and move logs ea. Synthetic Rope (amsteel blue) 9/16" x 150' used with TU 28 griphoist to pull and move logs ea. Synthetic Rope (amsteel blue) 5/8" x 150' used with TU 32 griphoist to pull and move logs ea. Choker 1/2" x 10' used with TU 17 griphoist to pull and move logs ea. Choker 5/8" x 15' used with TU 28 griphoist to pull and move logs ea. Choker 3/4" x 20' used with TU 32 griphoist to pull and move logs ea. Chain, Grade 100, 9/32" x 20' Includes Grab Hooks used with TU 28 griphoist to pull and move logs ea. Chain, Grade 100, 3/8" x 20' Includes Grab Hooks used with TU 28 griphoist to pull and move logs ea. used to attach wire rope sling to log for pulling across Tong, Skidding, 24" spread the ground ea. Gripper, Klein Extra Strength 8,000 lb. min. (3/16" to 1/2" wire rope) used to splice into wire rope slings without a shackle ea. Gripper, Klein Extra Strength15,000 lb. min. (1/2" to 3/4" wire rope) used to splice into wire rope slings without a shackle ea. Shackle, bell shaped screw pin, 5/8" pin, 3.5 ton WLL used to attach wire rope slings and chokers together ea. Shackle, bell shaped screw pin, 7/8" pin, 6.5 ton WLL used to attach wire rope slings and chokers together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 1" pin, 8.5 ton WLL endless slings together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 11/4" pin, 12 ton WLL endless slings together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 11/2" pin, 17 ton WLL endless slings together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 13/4" pin, 25 ton WLL endless slings together ea. Nylon Sling, eye each end, 2 ply 3" x 15' (7,100 lb. WLL choker set min.) used to anchor blocks and griphoist ea. Nylon Sling, eye each end, 2 ply 4" x 10' (9,200 lb. WLL choker set min.) used to anchor blocks and griphoist ea. Nylon Sling, eye each end, 2 ply 6" x 10' (13,000 lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Endless Sling, one ply, 1" x 8' (2,500lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Endless Sling, one ply, 3" x 10' (7,600lb. WLL choker set min.) used to anchor blocks and griphoist ea. Endless Sling, two ply, 3" x 10' (14,000lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Pig Tail, 7/8" x 2' Sling, Swaged Eyes, 13,200 lb. WLL used to attach griphoist to eye of nylon sling ea.

Pig Tail, 7/8" x 2', Swaged Eye and Eye Hook With Safety Latch, 13,200 lb. WLL used to attach griphoist to eye of nylon sling ea. Block, Standard 4", 4 ton WLL used for change of direction and mechanical Min. advantage with 3/8" - 1/2" wire rope ea. Block, Standard 5", 4 ton WLL used for change of direction and mechanical Min. advantage with 3/8" - 1/2" wire rope ea. Block, Standard 6", 8 ton WLL used for change of direction and mechanical Min. advantage with 1/2" - 3/4" wire rope ea. used to climb trees (to be pulled over) to hang choker Climbing Ladders Segmented and attach wire rope ea. Tree Saddle, Small used to support climber and attach pass rope ea. Tree Saddle, Medium used to support climber and attach pass rope ea. Tree Saddle, Large used to support climber and attach pass rope ea. Pass Rope Hemp Wire Core 15' used to climb trees and hold climber in tree ea. Pass Rope, Synthetic Wire Core 15' used to climb trees and hold climber in tree ea. Climbing Gaffs With Pads and used to climb trees (to be pulled over) to hang choker Straps and attach wire rope ea. Tag Line, 5/16" Climbing Rope, 50' used to pull up choker and wire rope ea. Carabiner, Locking used to attach small rigging items to tree saddle ea. used to anchor climber in tree while unhooking pass Lanyard rope or setting rigging ea. Hatchet used to remove limbs on tree ea. Chainsaw, 12" Bar used to remove limbs on tree ea. used to attach hatchet or chainsaw to climbing belt to Nylon Sling 1" x 3' tree saddle or micro block to tree limb ea. Nylon Sling 1" x 6' used to attach micro block to tree limb or tree ea. Dynamometer, 12.5 ton used to monitor the amount of force being applied at Capacity various locations in the rigging system ea. Shackles, Bow 1 1/2" Pin, 17 ton WLL used to attach dynamometer to wire rope ea. used to monitor the amount of force being applied at Dynamometer, 25 ton Capacity various locations in the rigging system ea. Shackles, Bow 2" Pin, 35 ton WLL used to attach dynamometer to wire rope ea. Wire Rope Cutter 1 1/6" Capacity used to cut wire rope in the field ea. Double Jack 8lb. used to strike wire rope cutter ea. Pliers used to remove cotter pins from blocks ea. High Leads Used in Moving Materials and Placing Logs, Rocks and Bridge Stringers

Tool/Equipment Function/Use No. Unit used to identify height of anchors in spar trees, determine angle of deflection and estimate lengths of Clinometer wire rope needed for rigging operation ea. used with clinometer to estimate length as of wire rope Tape Measure Cloth, 200' needed for rigging operation ea. used to estimate lengths of wire rope needed for Range Finder rigging operation ea. 2,000 lb. capacity hoist used to lift, move and place materials, logs, rocks and stringers (hoist includes Griphoist TU 17 mainline and handle) ea. 4,000 lb. capacity hoist used to lift, move and place materials, logs, rocks and stringers (hoist includes Griphoist TU 28 mainline and handle) ea. 8,000 lb. capacity hoist used to lift, move and place materials, logs, rocks and stringers (hoist includes Griphoist TU 32 mainline and handle) ea. sockets and ratchet for removing side covers, shear pins for all three hoist, pickle fork, ball peen hammer Griphoist Repair Kit and quart of 90 weight oil ea.

Wire Rope Sling 3/8" x 50' used with TU 17 griphoist to pull, lift and move loads ea.

Wire Rope Sling 3/8" x 100' used with TU 17 griphoist to pull, lift and move loads ea.

Wire Rope Sling 3/8" x 200' used with TU 17 griphoist to pull, lift and move loads ea.

Wire Rope Sling 1/2" x 50' used with TU 28 griphoist to pull, lift and move loads ea.

Wire Rope Sling 1/2" x 100' used with TU 28 griphoist to pull, lift and move loads ea.

Wire Rope Sling 1/2" x 200' used with TU 28 griphoist to pull, lift and move loads ea.

Wire Rope Sling 3/4" x 50' used with TU 32 griphoist to pull, lift and move loads ea.

Wire Rope Sling 3/4" x 100' used with TU 32 griphoist to pull, lift and move loads ea.

Wire Rope Sling 3/4" x 200' used with TU 32 griphoist to pull, lift and move loads ea. Synthetic Rope (amsteel blue) 1/2" x 200' used with TU 17 griphoist to pull, lift and move loads ea. Synthetic Rope (amsteel blue) 9/16" x 200' used with TU 28 griphoist to pull, lift and move loads ea. Synthetic Rope (amsteel blue) 5/8" x 200' used with TU 32 griphoist to pull, lift and move loads ea. used with TU 17 griphoist to attach loads to wire rope Choker 1/2" x 10' sling and move to desired location ea. used with TU 28 griphoist to attach loads to wire rope Choker 5/8" x 15' sling and move to desired location ea. used with TU 32 griphoist to attach loads to wire rope Choker 3/4" x 20' sling and move to desired location ea. Chain, Grade 100, 9/32" x 20' used with TU 17 and 28 griphoist to attach loads to Includes Grab Hooks wire rope sling and move to desired location ea. Chain, Grade 100, 3/8" x 20' used with TU 32 griphoist to attach loads to wire rope Includes Grab Hooks sling and move to desired location ea. used to attach rocks to wire rope sling and move rocks Nylon Rock Sling to desired location ea. used to attach rocks to wire rope sling and move rocks Chain Rock Sling to desired location ea. used to attach rocks to wire rope sling and move rocks Cable Rock Sling to desired location ea. used to attach rocks to wire rope sling and move rocks to desired location, sling grabs rocks on its sides to facilitate setting rock at desired location without having Ratchet Nylon Rock Sling sling under the rock ea. Gripper, Klein Extra Strength 8,000 lb. min. (3/16" to 1/2" used to splice into wire rope slings without a shackle wire rope) and tighten wire rope used as guy lines ea. Gripper, Klein Extra Strength15,000 lb. min. (1/2" to used to splice into wire rope slings without a shackle 3/4" wire rope) and tighten wire rope used as guy lines ea. Shackle, bell shaped screw pin, 5/8" pin, 3.5 ton WLL used to attach wire rope slings and chokers together ea. Shackle, bell shaped screw pin, 7/8" pin, 6.5 ton WLL used to attach wire rope slings and chokers together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 1" pin, 8.5 ton WLL endless slings together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 11/4" pin, 12 ton WLL endless slings together ea. Shackle, Counter Sunk Pin, used to attach wire rope slings together and pull them 3/4" pin, 6 ton WLL through a pass block ea. Shackle, Counter Sunk Pin, used to attach wire rope slings together and pull them 7/8" pin, 9 ton WLL through a pass block ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 11/2" pin, 17 ton WLL endless slings together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 13/4" pin, 25 ton WLL endless slings together ea. Nylon Sling, eye each end, 2 ply 3" x 15' (7,100 lb. WLL choker set min.) used to anchor blocks and griphoist ea. Nylon Sling, eye each end, 2 ply 4" x 10' (9,200 lb. WLL choker set min.) used to anchor blocks and griphoist ea. Nylon Sling, eye each end, 2 ply 6" x 10' (13,000 lb. WLL choker set min.) used to anchor blocks and griphoist ea. Nylon Sling, eye each end, 2 ply 6" x 20' (13,000 lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Endless Sling, one ply, 1" x 8' (2,500lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Endless Sling, one ply, 3" x 10' (7,600lb. WLL choker set min.) used to anchor blocks and griphoist ea. Endless Sling, two ply, 3" x 10' (14,000lb. WLL choker set min.) used to anchor blocks and griphoist ea. Endless Sling, two ply, 3" x 20' (14,000lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Pig Tail, 7/8" x 2' Sling, Swaged Eyes, 13,200lb. WLL used to attach griphoist to eye of nylon sling ea.

Pig Tail, 7/8" x 2', Swaged Eye and Eye Hook With Safety Latch, 13,200 lb. WLL used to attach griphoist to eye of nylon sling ea. Block, Standard 4", 4 ton WLL used for change of direction and mechanical Min. advantage with 3/8" - 1/2" wire rope ea. Block, Standard 5", 4 ton WLL used for change of direction and mechanical Min. advantage with 3/8" - 1/2" wire rope ea. Block, Standard 6", 8 ton WLL used for change of direction and mechanical Min. advantage with 1/2" - 3/4" wire rope ea.

Block, pass or rig up 8", 8 ton used for change of direction, mechanical advantage SWL Min. and passing shackle through block 1/2"-3/4" wire rope ea. Climbing Ladders, Segmented (Stackable) used to climb trees to hang rigging ea. Tree Saddle, Small used to support climber and attach pass rope ea. Tree Saddle, Medium used to support climber and attach pass rope ea. Tree Saddle, Large used to support climber and attach pass rope ea. Pass Rope Hemp Wire Core 15' used to climb trees and hold climber in tree ea. Pass Rope Hemp Wire Core 20' used to climb trees and hold climber in tree ea. Pass Rope Hemp Wire Core 30' used to climb trees and hold climber in tree ea. Pass Rope, Synthetic Wire Core 15' used to climb trees and hold climber in tree ea. Climbing Gaffs With Pads and Straps used to climb trees to hang rigging ea. Hatchet used to remove limbs on tree ea. Chainsaw, 12" Bar used to remove limbs on tree ea. Micro Rope Pulley used with tag line to send rigging up to climber ea. Tag Line, 5/16" Climbing Rope, 50' used with micro pulley to send rigging up to climber ea. Tag Line, 5/16" Climbing Rope, 100' used with micro pulley to send rigging up to climber ea. Tag Line, 5/16" Climbing Rope, 150' used with micro pulley to send rigging up to climber ea. Carabiner, Locking used to attach small rigging items to tree saddle ea. used to anchor climber in tree while unhooking pass Lanyard rope or setting rigging ea. used to attach hatchet or chainsaw to climbing belt to Nylon Sling 1" x 3' tree saddle or micro block to tree limb ea. Nylon Sling 1" x 6' used to attach micro block to tree limb or tree ea. Dynamometer, 12.5 ton used to monitor the amount of force being applied at Capacity various locations in the rigging system ea. Shackles, Bow 1 1/2" Pin, 17 ton WLL used to attach dynamometer to wire rope ea. used to monitor the amount of force being applied at Dynamometer, 25 ton Capacity various locations in the rigging system ea. Shackles, Bow 2" Pin, 35 ton WLL used to attach dynamometer to wire rope ea. Wire Rope Cutter 1 1/6" Capacity used to cut wire rope in the field ea. Double Jack 8lb. used to strike wire rope cutter ea. used with Flemish eye to form an eye at the end of a Wire Rope Clips 3/8" wire rope and secure guy line ea. used with Flemish eye to form an eye at the end of a Wire Rope Clips 1/2" wire rope and secure guy line ea. used with Flemish eye to form an eye at the end of a Wire Rope Clips 3/4" wire rope and secure guy line ea. Sockets and Ratchet used to secure clips to wire rope ea. used with Flemish eye to form an eye at the end of a Swages Oval 3/8" wire rope ea. used with Flemish eye to form an eye at the end of a Swages Oval 1/2" wire rope ea.

Hydraulic Hand Swaging Tool used to compress swales tightly around wire rope ea. used to lift bridge stringers when adjusting their High Lift Jack position on the beam seat brackets ea. used to lever bridge stringers when making minor Rock Bar position adjustments ea. Pliers used to remove cotter pins from blocks ea. Skylines, Transverse Anchors and High leads off of Skylines Used in Moving Materials and Placing Logs, Rocks and Bridge Stringers

Tool/Equipment Function/Use No. Unit used to identify height of anchors in spar trees, determine angle of deflection and estimate lengths of Clinometer wire rope needed for rigging operation ea. used with clinometer to estimate length as of wire rope Tape Measure Cloth, 200' needed for rigging operation ea. used to estimate lengths of wire rope needed for Range Finder rigging operation ea. 2,000 lb. capacity hoist used to lift, move and place materials, logs, rocks and stringers (hoist includes Griphoist TU 17 mainline and handle) ea. 4,000 lb. capacity hoist used to lift, move and place materials, logs, rocks and stringers (hoist includes Griphoist TU 28 mainline and handle) ea. 8,000 lb. capacity hoist used to lift, move and place materials, logs, rocks and stringers (hoist includes Griphoist TU 32 mainline and handle) ea. sockets and ratchet for removing side covers, shear pins for all three hoist, pickle fork, ball peen hammer Griphoist Repair Kit and quart of 90 weight oil ea. 2,200 lb. capacity winch used to pull haul back line on Capstan Winch, Gas Powered skyline ea. 3/8" Double Braided Polyester Rope, 600' rope used as haul back line with capstan winch ea. 2,200 lb. capacity winch used to pull haul back line on Tirfor Gripwinch skyline ea. 12 KVA 3 Phase Generator used to power Tirfor gripwinch ea.

Tirfor 8 MM Wire Rope 1,000' wire rope haul back line required to use with gripwinch ea. used to transport and anchor gripwinch, generator and 1 Ton Flatbed Truck wire rope spool ea.

Wire Rope Sling 3/8" x 50' used with TU 17 griphoist to pull, lift and move loads ea. used with TU 17 griphoist to pull, lift and move loads Wire Rope Sling 3/8" x 100' and skylines ea. used with TU 17 griphoist to pull, lift and move loads Wire Rope Sling 3/8" x 200' and skylines ea.

Wire Rope Sling 1/2" x 50' used with TU 28 griphoist to pull, lift and move loads ea. used with TU 28 griphoist to pull, lift and move loads Wire Rope Sling 1/2" x 100' and skylines ea. used with TU 28 griphoist to pull, lift and move loads Wire Rope Sling 1/2" x 200' and skylines ea.

Wire Rope Sling 3/4" x 50' used with TU 32 griphoist to pull, lift and move loads ea. used with TU 32 griphoist to pull, lift and move loads Wire Rope Sling 3/4" x 100' and skylines ea. used with TU 32 griphoist to pull, lift and move loads Wire Rope Sling 3/4" x 200' and skylines ea.

Wire Rope Spool 3/8" x 1000' used for the skyline when > 200' wire rope is required ea.

Wire Rope Spool 1/2" x 1000' used for the skyline when > 200' wire rope is required ea. Wire Rope Spool 3/4" x 1000' used for the skyline when > 200' wire rope is required ea. Rubber Coated Wire Rope used when transporting stringers with helicopters to Sling 5/8" x 50' eliminate static shock to ground workers ea. rope is tied to bridge stringers being transported by 1/2" Double Braided Polyester helicopter and used by ground crews to guide stringers Rope, 100' onto abutments ea. Sauerman Continuous Cable used to splice into spools of 3/8" wire rope used as Clamp 3/8" Capacity skylines ea. Sauerman Continuous Cable used to splice into spools of 1/2" wire rope used as Clamp 1/2" Capacity skylines ea. Sauerman Continuous Cable used to splice into spools of 3/4" wire rope used as Clamp 3/4" Capacity skylines ea. Synthetic Rope (amsteel blue) 1/2" x 300' used with TU 17 griphoist as haul back lines ea. Synthetic Rope (amsteel blue) 9/16" x 300' used with TU 28 griphoist as haul back lines ea. Synthetic Rope (amsteel blue) 5/8" x 300' used with TU 32 griphoist as haul back lines ea. used with TU 17 griphoist to attach loads to wire rope Choker 1/2" x 10' sling and move to desired location ea. used with TU 28 griphoist to attach loads to wire rope Choker 5/8" x 15' sling and move to desired location ea. used with TU 32 griphoist to attach loads to wire rope Choker 3/4" x 20' sling and move to desired location ea. Chain, Grade 100, 9/32" x 20' used with TU 17 and 28 griphoist to attach loads to Includes Grab Hooks wire rope sling and move to desired location ea. Chain, Grade 100, 3/8" x 20' used with TU 32 griphoist to attach loads to wire rope Includes Grab Hooks sling and move to desired location ea. used to attach rocks to wire rope sling and move rocks Nylon Rock Sling to desired location ea. used to attach rocks to wire rope sling and move rocks Chain Rock Sling to desired location ea. used to attach rocks to wire rope sling and move rocks Cable Rock Sling to desired location ea. used to attach rocks to wire rope sling and move rocks to desired location, sling grabs rocks on its sides to facilitate setting rock at desired location without having Ratchet Nylon Rock Sling sling under the rock ea. Gripper, Klein Extra Strength 8,000 lb. min. (3/16" to 1/2" used to splice into wire rope slings without a shackle wire rope) and tighten wire rope used as guy lines ea. Gripper, Klein Extra Strength15,000 lb. min. (1/2" to used to splice into wire rope slings without a shackle 3/4" wire rope) and tighten wire rope used as guy lines ea. Shackle, bell shaped screw pin, 5/8" pin, 3.5 ton WLL used to attach wire rope slings and chokers together ea. Shackle, bell shaped screw pin, 7/8" pin, 6.5 ton WLL used to attach wire rope slings and chokers together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 1" pin, 8.5 ton WLL endless slings together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 11/4" pin, 12 ton WLL endless slings together ea. Shackle, Counter Sunk Pin, used to attach wire rope slings together and pull them 3/4" pin, 6 ton WLL through a pass block ea. Shackle, Counter Sunk Pin, used to attach wire rope slings together and pull them 7/8" pin, 9 ton WLL through a pass block ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 11/2" pin, 17 ton WLL endless slings together ea. Shackle, bell shaped screw used to attach wire rope slings, chokers, nylon and pin, 13/4" pin, 25 ton WLL endless slings together ea. Nylon Sling, eye each end, 2 ply 3" x 15' (7,100 lb. WLL choker set min.) used to anchor blocks and griphoist ea. Nylon Sling, eye each end, 2 ply 4" x 10' (9,200 lb. WLL choker set min.) used to anchor blocks and griphoist ea. Nylon Sling, eye each end, 2 ply 6" x 10' (13,000 lb. WLL choker set min.) used to anchor blocks and griphoist ea. Nylon Sling, eye each end, 2 ply 6" x 20' (13,000 lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Endless Sling, one ply, 1" x 8' (2,500lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Endless Sling, one ply, 3" x 10' (7,600lb. WLL choker set min.) used to anchor blocks and griphoist ea. Endless Sling, two ply, 3" x 10' (14,000lb. WLL choker set min.) used to anchor blocks and griphoist ea. Endless Sling, two ply, 3" x 20' (14,000lb. WLL choker set min.) used to anchor blocks and griphoist ea.

Pig Tail, 7/8" x 2' Sling, Swaged Eyes, 13,200lb. WLL used to attach griphoist to eye of nylon sling ea.

Pig Tail, 7/8" x 2', Swaged Eye and Eye Hook With Safety Latch, 13,200 lb. WLL used to attach griphoist to eye of nylon sling ea. Block, Standard 4", 4 ton WLL used for change of direction and mechanical Min. advantage with 3/8" - 1/2" wire rope ea. Block, Standard 5", 4 ton WLL used for change of direction and mechanical Min. advantage with 3/8" - 1/2" wire rope ea. Block, Swivel 5", 4 ton WLL used for attaching high lead rigging to skyline and Min. change of direction 3/8" - 1/2" wire rope ea. Block, Standard 6", 8 ton WLL used for change of direction and mechanical Min. advantage with 1/2" - 3/4" wire rope ea. Block, Swivel 6", 8 ton WLL used for attaching high lead rigging to skyline and Min. change of direction 1/2" - 3/4" wire rope ea.

Block, pass or rig up 8", 8 ton used for change of direction, mechanical advantage SWL Min. and passing shackle through block 1/2"-3/4" wire rope ea. Climbing Ladders, Segmented (Stackable) used to climb trees to hang rigging ea. Tree Saddle, Small used to support climber and attach pass rope ea. Tree Saddle, Medium used to support climber and attach pass rope ea. Tree Saddle, Large used to support climber and attach pass rope ea. Pass Rope Hemp Wire Core 15' used to climb trees and hold climber in tree ea. Pass Rope Hemp Wire Core 20' used to climb trees and hold climber in tree ea. Pass Rope Hemp Wire Core 30' used to climb trees and hold climber in tree ea. Pass Rope, Synthetic Wire Core 15' used to climb trees and hold climber in tree ea. Climbing Gaffs With Pads and Straps used to climb trees to hang rigging ea. Hatchet used to remove limbs on tree ea. Chainsaw, 12" Bar used to remove limbs on tree ea. Micro Rope Pulley used with tag line to send rigging up to climber ea. Tag Line, 5/16" Climbing Rope, 50' used with micro pulley to send rigging up to climber ea. Tag Line, 5/16" Climbing Rope, 100' used with micro pulley to send rigging up to climber ea. Tag Line, 5/16" Climbing Rope, 150' used with micro pulley to send rigging up to climber ea. Carabiner, Locking used to attach small rigging items to tree saddle ea. used to anchor climber in tree while unhooking pass Lanyard rope or setting rigging ea. used to attach hatchet or chainsaw to climbing belt to Nylon Sling 1" x 3' tree saddle or micro block to tree limb ea. Nylon Sling 1" x 6' used to attach micro block to tree limb or tree ea. Dynamometer, 12.5 ton used to monitor the amount of force being applied at Capacity various locations in the rigging system ea. Shackles, Bow 1 1/2" Pin, 17 ton WLL used to attach dynamometer to wire rope ea. used to monitor the amount of force being applied at Dynamometer, 25 ton Capacity various locations in the rigging system ea. Shackles, Bow 2" Pin, 35 ton WLL used to attach dynamometer to wire rope ea. Wire Rope Cutter 1 1/6" Capacity used to cut wire rope in the field ea. Double Jack 8lb. used to strike wire rope cutter ea. used with Flemish eye to form an eye at the end of a Wire Rope Clips 3/8" wire rope and secure guy line ea. used with Flemish eye to form an eye at the end of a Wire Rope Clips 1/2" wire rope and secure guy line ea. used with Flemish eye to form an eye at the end of a Wire Rope Clips 3/4" wire rope and secure guy line ea. Sockets and Ratchet used to secure clips to wire rope ea. used with Flemish eye to form an eye at the end of a Swages Oval 3/8" wire rope ea. used with Flemish eye to form an eye at the end of a Swages Oval 1/2" wire rope ea.

Hydraulic Hand Swaging Tool used to compress swages tightly around wire rope ea.

Tripod (Forest Service Style) With Leg Extensions, Max. 10' Height, 2 Ton Capacity used as spars for taught skylines ea.

Tripod (Forest Service Style) With Leg Extensions, Max. 20' Height, 4 Ton Capacity used as spars for taught skylines ea. Tripod Aluminum With Leg Extensions Max Height 13', 2 Ton Capacity used as spars for taught skylines ea. Duckbill Ground Anchor, 5,000 used to anchor hoist/winches in absence of trees and lb. Holding Capacity rock ea. Driving Rod used to drive anchor into earth ea. Cobra Combi Gas Powered used to drive in duckbill anchor and drill expansion bolt Rock Drill and Breaker anchor holes into rock ea. Tool Box With Assorted Wrenches, Sockets, Screw used to perform minor adjustments, maintenance and Drivers, & Rags repairs to gas powered tools ea. used to clean up minor gas and oil spills realted to gas Universal Bag Spill Kit, 5 Gal. powered tools ea. used to anchor hoist/winches in absence of trees and Tirfor Earth Anchor Plates rock ea. Double Jack 8 lb. used to drive in anchor pins ea. used to anchor hoist/winches in absence of trees and Tirfor Earth Screw Anchors rock ea. Generator 2,500 Watt used to power roto hammer drill ea. Roto Hammer, Electric 1/2" used to drill 3/4" hole in rock for expansion bolt ea. 11/16" Rock Drill Bit used to drill hole in rock for 5/8" wedge anchor ea. Wedge Anchor 5/8" x 5' used to anchor plate ea. Anchor Plate 1/4" Steel With attached to 5/8" wedge anchor to anchor 3/4" Attachment Holes hoist/winches in absence of trees and rock ea.

7/8" Rock Drill Bit used to drill hole in rock for 3/4" Flemish eye anchor ea. 3/4" Wire Rope Flemish Eye With 12" Tail glued into rock to anchor hoist/winch ea. Rechargeable Aerosol Spray used to blow rock dust out drill holes before gluing Can 200 PSI stainless steel rod ea. Hilti Glue Gun and Glue used to secure Flemish eye to rock ea. 1 7/8" Rock Drill Bit used to drill 1 7/8" hole in rock for expansion bolt ea. used to anchor hoist/winches in absence of trees and Rock Expansion Bolt rock ea. I Beam Lifting Clamp 6"-14" Opening, 20,000 lb. WLL used to attach steel I beam bridge stringers to skyline ea. Broad Head Bull Pin 1 1/4" Top used to align bolt holes in segmented steel I beam and x 13 3/4" Length aluminum truss bridge stringers ea. Broad Head Bull Pin 1 1/16" used to align bolt holes in segmented steel I beam and Top x 10" Length aluminum truss bridge stringers ea. used to align bolt holes in segmented steel I beam and Aligning Pry Bar 30" aluminum truss bridge stringers ea. Deep Well Socket Set 1/2" used to attach bolts and nuts holding steel I beam Drive stringer segments together ea. used with sockets to attach bolts and nuts holding Ratchet 1/2" Drive steel I beam stringer segments together ea. used with sockets to attach bolts and nuts holding Box End Wrench Set steel I beam stringer segments together ea. used to transport 5 gal. buckets of earth/rock over Bucket Sling skyline ea. used to attach 55 gallon drum to skyline and dump 55 Gallon Drum Tipper contents at destination ea. used to lift bridge stringers when adjusting their High Lift Jack position on the beam seat brackets ea. used to lever bridge stringers when making minor position adjustments and aligning bolt holes when splicing steel I beam and aluminum truss segments Pinch Point Crow Bar 60" together ea. Pliers used to remove cotter pins from blocks ea.