TechNotes V1.0
Industrial Mainboard Series Mini-ITX
D3433-S D3434-S
Content
1 Safety Instructions 6 2 Feature Overview 7 2.1 Summary: Feature overview D343x-S 7 2.2 Basic Layout & External Connectors D3433-S 9 2.3 Basic Layout & External Connectors D3434-S 10 2.4 Block Diagram D3433-S 11 2.5 Block Diagram D3434-S 12 2.6 Onboard components D3433-S & D3434-S 13 2.7 I/O-Shield 14 3 Interfaces & Connectors 15 3.1 Frontpanel Connector 15 3.2 Internal Serial (COM) Port Connector 16 3.3 External Serial (COM) Port Connector 16 3.4 Internal USB2.0 Connector (2 Ports) 17 3.5 Internal USB3.0 Pin Connector (2 Ports) 17 3.6 Internal USB3.0 Stick Socket 18 3.7 External USB3.0 Connector 18 3.8 PS/2 Keyboard Port 19 3.9 PS/2 Mouse Port 19 3.10 LAN Connector 20 3.11 DVI-D Connector 20 3.12 DisplayPort V1.2 Connector 21 3.13 Embedded DisplayPort Connector 22 3.14 Serial ATA Connector 23 3.15 mSATA Pinout / Mini-PCIe Pinout – Fullsize 24 3.16 mSATA / Mini-PCIe BIOS Setup Options 25 3.17 m-SATA / Mini-PCIe Socket Assembly Note 26 3.18 M.2 (Key M) – 2242 & 2260 27
a TechNotes D343x-S V0.2 Page 2 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
3.19 M.2 Socket Assembly Note 28 3.20 Possible configurations for M.2 & Minicard –Modules 29 3.21 PCIe x16 Slot Configuration for Riser cards (only supported for D3433-S) 30 3.22 Fan Connectors 31 3.23 Rear Audio / Frontpanel Audio Connector 32 3.24 S/PDIF Connector 34 3.25 GPIO (Feature Connector) 35 3.26 Power Supply Connector (Multirail) 36 3.27 Additional Power Supply Connector (12V for Processor) 36 3.28 Power Supply Connectors (ATX Multirail or Single 12V Operation) 37 3.28.1 ATX Multirail Operation 37 3.28.2 Single 12V Operation 38 3.28.3 Single 12V Operation – Config 39 3.29 Chassis Intrusion 40 4 System Monitoring 41 4.1 D343x-S: Temperature Sensors and Fan Connectors (preliminary) 42 4.2 SystemGuard 43 4.3 SystemGuard - Details 44 4.4 SilentFanConfigManager – Customize System Monitoring Settings 45 4.5 Components for continous 24/7 operation @ +60°C 46 4.6 Capacitor Endurance Time Comparison 47 4.7 Temperature Reference Points D343x-S 48 4.8 Temperature Reference Points D343x-S (rear) 49 4.9 BMC – BIOS Default Settings D343x-S 50 5 Power Supply 51 5.1 ATX Power Supply 51 5.2 Typcial Power Consumption (to be added soon) 52 6 USB Implementation 53 6.1 USB Ports & USB Power Fuses (D3433-S) 53 6.2 USB Ports & USB Power Fuses (D3434-S) 55 7 Display Options 57 7.1 Summary: Video Output Options D343x-S 57 7.2 LVDS Display & Backlight Inverter 59 7.3 LVDS Connector Details 60
a TechNotes D343x-S V0.2 Page 3 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
7.4 Backlight Inverter Connector Details 61 7.5 LVDS Timing & Screen Resolution 62 7.6 LVDS Tool 65 7.7 LVDS – Influence on Graphics Output (prelim.) 66 7.8 LVDS Cabling Reference 67 7.9 LVDS Sample Cabling for AuO-G150 68 7.10 Embedded DisplayPort (prelim.) 69 7.11 Embedded Display Port Power 70 8 Operating System Support 71 8.1 Support for Windows 7 / Windows 8.1 / Windows 10 72 8.2 Linux Support (to be added soon) 73 9 Mainboard Tools 74 Common Mainboard Tools 74 9.1 BIOS Boot Logo Tool 74 9.2 EditCMOS 74 9.3 OEMIDENT 74 9.4 SystemGuard 75 Industrial Tools 76 9.5 SilentFanConfig-Manager 76 9.6 Windows System-Monitoring API (BMCAPI) 77 9.7 Linux System-Monitoring Driver (“LM-Sensors”) To be added soon 77 10 Known Issues & Important Notes 78 10.1 USB 2.0 / MS Windows 7 78 10.2 TPM2.0 / MS Windows 7 78 11 Miscellaneous 79 11.1 Battery Lifetime 79 11.2 RealTime Clock (RTC) Accuracy 80 11.3 System Watchdog (WD) 81 11.4 BIOS Update / BIOS Recovery 84 11.5 BIOS/CMOS: Reset Defaults 85 11.6 BIOS integrated HW Diagnostic Tool 86 11.7 BIOS integrated Erase Disk Tool 86 11.8 Power indicator 87
a TechNotes D343x-S V0.2 Page 4 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
Revision History:
V1.0 First Version 22.02.2016
Technical data are subject to change without prior notice. Fujitsu accepts no responsibility with regards to technical or editorial mistakes or omissions.
a TechNotes D343x-S V0.2 Page 5 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
Safety Instructions 1 Safety Instructions
Do not connect or disconnect any cables or modules to or from any onboard connectors (except for the rear I/O connectors) until the mainboard is completely powered down.
Any damage caused to the mainboard by misuse of the onboard connectors is excluded from the standard warranty. Fujitsu Technology Solutions cannot be held liable for any damage that results from incorrect use of any onboard connectors.
The system integrator is fully responsible for the usage of appropriate connectors and cables in order to fulfill the technical requirements (electrical contact, durability, power/current levels, signal integrity etc.)
TechNotes D307x-S V1.1 3 Copyright 2011 FUJITSU
a TechNotes D343x-S V0.2 Page 6 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
2 Feature Overview 2.1 Summary: Feature overview D343x-S
Feature D3433-S D3434-S Note
Chipset (PCH) Q170 H110 incl. heatsink 2 / 32GB DDR4-2133 2 / 32GB DDR4-2133 Memory Sockets / max. RAM / ECC Support SO-DIMM / Non-ECC / Non-ECC Intel® Core™ i7 / i5 / i3 – (6th gen.) processor series (max. 65W TDP) x x K-Series not supported!
Intel® Pentium® / Celeron® processor series (max. 65W TDP) x x
TPM V1.2 / TPM V2.0 -- / Infineon -- / Intel integrated
1) 1) halfsize / fullsize possible, mSATA Socket / Mini-PCIe Socket / 8 Bit GPIO x / x / x -- / x / x incl. USB2.0 PCIe x2 & SATA based M.2 SATA based M.2 Mechanical support for M.2 Socket 42mm and 60mm modules; modules supported modules supported Key M USB2.0 Ports internal / external 2 / 4 2 / 3
USB3.0 Ports internal / external / USB 3.0 Stick Socket onboard 2 / 4 / x 2 / 2 / -
Fan 1 /2 / 3 / 4 x / -- / x / -- x / -- / x / --
FAN3: PWM or 3Pin x x BIOS Setup option
Onboard LVDS 24bit / eDP (2 lanes) x / x x / x Simultaneous use possible
SATA3 / RAID Support (0/1/5/10) 4 / x 2 / --
S/P-DIF / Intrusion x / x x / x
1) Shared socket mSATA / Mini-PCIe
a TechNotes D343x-S V0.2 Page 7 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
Feature Overview Summary: Feature overview D343x-S (continued)
Feature D3433-S D3434-S Notes Gen3; Support for lane split Gen3 Slot #1: PCIe x16 (PEG Slot) Riser: 2x PCIe x8 or 1x No lane split support PCIe8 and 2x PCIe4 COM-Port external / COM-Port internal / Parallel Port internal 1 / 1 / -- 1 / 1 / --
Up to 3 independent displays DVI-I / DVI-D / DisplayPort 1 / DisplayPort 2 / LVDS / Emb. DisplayPort -- / x / x / x / x / x -- / x / x / -- / x / x (D3434 / H110: max. 2) 1) Dual LAN / Intel iAMT 11 - vPro 2015 Manageability x / x x / -- Incl. Teaming Support;
BIOS-POST / BIOS-Boot / OS – HW Watchdog onboard x / x / x x / x / x Improved electrical signal 8 Layer PCB x x quality & improved durability Approved for 24/7 operation @ 60°C / full load x x
UL/CSA 60950-1 certification planned planned
FCC/B approval planned planned
EraseDisk (BIOS Feature) included x x
1) iAMT (Q170) requires appropriate Core i5 / Core i7 processor;
a TechNotes D343x-S V0.2 Page 8 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
Feature Overview
2.2 Basic Layout & External Connectors D3433-S
Mouse 4x USB2.0 COM1 LAN2 LAN1 (iAMT)
Kbd 2x DisplayPort V1.2 DVI-D 4x USB 3.0 Audio
a TechNotes D343x-S V0.2 Page 9 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
9
Feature Overview
2.3 Basic Layout & External Connectors D3434-S
Mouse 1x USB2.0 COM1 LAN2 LAN1
Kbd 1x DisplayPort V1.2 DVI-D 2x USB 2.0 2x USB 3.0 Audio
a TechNotes D343x-S V0.2 Page 10 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Feature Overview
2.4 Block Diagram D3433-S
a TechNotes D343x-S V0.2 Page 11 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Feature Overview
2.5 Block Diagram D3434-S
a TechNotes D343x-S V0.2 Page 12 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Feature Overview
2.6 Onboard components D3433-S & D3434-S CPU LGA1151 max. 65W
eDP (2Lanes) mSATA(D3433-S only) / Mini-PCIe Intrusion Fan3 (4 pin PWM / 3 pin) Frontpanel COM2 Port
4 x SATA-III = D3433-S M.2 - SATA / PCIe (D3433-S only)
USB 3.0 Socket (D3433-S only) PCIe x16 (16 Lanes, Gen3)
D3433-S only: Lane split 2 x SATA-III = D3434-S supported 2 x USB 2.0 (Internal)
8 Layer PCB 2x USB 3.0 (Frontpanel)
24 pin ATX PSU / 12V DC Supply
12V Supply (Processor)
Processor Fan (4 Pin) Frontpanel Audio
Backlight LVDS GPIO Port
24bit dual channel LVDS S/PDIF Output
a TechNotes D343x-S V0.2 Page 13 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Feature Overview
2.7 I/O-Shield
USB/DP-cover to be removed for D3433-S
Spring Steel Sheet
Enforcement Sheet
Nominal force: ~ 75 N Rear Side: EMI Gasket for specified ATX IO “letterbox”
(Foam with Copper Nickel Note: ATX Chassis “letterbox” for I/O shield: fabric) Nom. size = 158.75 x 44.45mm
Tolerance = +/- 0.2mm
a TechNotes D343x-S V0.2 Page 14 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
3 Interfaces & Connectors 3.1 Frontpanel Connector
Pin Signal Pin Signal 1 HD-LED + 2 Power LED + Pin 1 Pin 2 3 HD-LED - 4 Power LED - 5 GND 6 Power_Button 7 RST_L 8 GND 9 reserved 10 Key 11 reserved 12 GND 13 BMC Alert LED + 14 BMC Alert LED - 15 reserved 16 reserved 17 Speaker + 18 BIOS Testmode (reserved) 19 GND 20 GND (0,1K) 21 Key 22 GND (0,1K) 23 Speaker - 24 Recover BIOS
Power LED: Anode: Pin 2 – current source 3mA up to 4V Cathode: Pin 4 (suitable for various LED colors)
HDD LED: Anode: Pin 1 – current source 3mA up to 4V Cathode: Pin 3 (suitable for various LED colors)
Internal Speaker Output: Differential audio signal; mono, max. 2W RMS / 4Ohm Note: System Beeps are audible via the internal speaker output only, even if a device is connected to the external audio ports (rear/front) .
a TechNotes D343x-S V0.2 Page 15 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Interfaces & Connectors
3.2 Internal Serial (COM) Port Connector
Pin Signal Pin Signal
1 DCD 2 2 DSR 2 Pin 1 Pin 2 3 SIN 2 4 RTS 2 5 SOUT 2 6 CTS 2 7 DTR 2 8 RI 2 9 GND 10 Key
Note: D3433/34: The internal COM-Port is COM2
3.3 External Serial (COM) Port Connector
Pin Signal Pin Signal Pin 1 1 DCD 1 6 DSR 1 2 SIN 1 7 RTS 1 3 SOUT 1 8 CTS 1 4 DTR 1 9 RI 1 Pin 6 5 GND
a TechNotes D343x-S V0.2 Page 16 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Interfaces & Connectors
3.4 Internal USB2.0 Connector (2 Ports) Note: All USB3 connectors provide separate signal Pin Signal Pin Signal lines for USB3.0 and USB2.0! 1 VCC AUX (fuse protected) 2 VCC AUX (fuse protected) Pin 1 Pin 2 3 Data negative Port X 4 Data negative Port Y All “fused” ports provide max. 500mA 5 Data positive Port X 6 Data positive Port Y (USB2.0) resp. . 900mA (USB3.0) for each 7 GND 8 GND port 9 Key 10 Not connected
3.5 Internal USB3.0 Pin Connector (2 Ports)
Pin Signal Pin Signal Pin 1 Pin 19 1 VCC AUX (polyswitch fused and power 2 USB3_RX negative (P2) supervision with over current detection) 3 USB3_RX positive (P2) 4 GND 5 USB3_TX negative (P2) 6 USB3_TX positive (P2) 7 GND 8 Data negative (P2) [USB2.0] 9 Data positive (P2) [USB2.0] 10 FP Detect 11 Data positive (P3) [USB2.0] 12 Data negative (P3) [USB2.0] 13 GND 14 USB3_TX positive (P3) 15 USB3_TX negative (P3) 16 GND 17 USB3_RX positive (P3) 18 USB3_RX negative (P3) 19 VCC AUX (polyswitch fused and power supervision with over current detection)
a TechNotes D343x-S V0.2 Page 17 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Interfaces & Connectors
3.6 Internal USB3.0 Stick Socket Note: Pin Signal All USB3 connectors provide separate signal 1 VCC auxiliary lines for USB3.0 and USB2.0! (polyswitch fused and power supervision with over current detection) Pin 9 2 Data negative [USB2.0] All “fused” ports provide max. 500mA (USB2.0) resp. . 3 Data positive [USB2.0] 4 GND 900mA (USB3.0) for each port 5 USB3_RX negative 6 USB3_RX positive Pin 1 7 GND 8 USB3_TX negative 9 USB3_TX positive
3.7 External USB3.0 Connector
Pin Signal 1 VCC auxiliary (polyswitch fused and power supervision with over current detection) Pin 9 2 Data negative [USB2.0] 3 Data positive [USB2.0] 4 GND 5 USB3_RX negative 6 USB3_RX positive Pin 1 7 GND 8 USB3_TX negative 9 USB3_TX positive
a TechNotes D343x-S V0.2 Page 18 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Interfaces & Connectors 3.8 PS/2 Keyboard Port
Pin Signal 1 KBD Data Pin 6 Pin 5 2 Not connected 3 GND Pin 4 Pin 3 (polyswitch fused) 4 VCC Pin 2 Pin 1 5 KBD CLK 6 Keyboard_On (low asserted pulse)
3.9 PS/2 Mouse Port
Pin Signal 1 MOUSE Data Pin 6 Pin 5 2 Not connected Pin 4 Pin 3 3 GND 4 VCC (polyswitch fused) Pin 2 Pin 1 5 MOUSE CLK 6 Not connected
a TechNotes D343x-S V0.2 Page 19 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
1
Interfaces & Connectors
3.10 LAN Connector
Pin Signal with 10/100/1000 Signal with 10/100 1 MX1 + TX + 2 MX1 - TX - 3 MX2 + RX + 4 MX3 + TERMPLANE 5 MX3 - TERMPLANE Pin 1 6 MX2 - RX - 7 MX4 + TERMPLANE 8 MX4 - TERMPLANE
3.11 DVI-D Connector
Pin Signal Pin Signal 1 Data2+ 13 NC 2 Data2- 14 Vcc (fused) 3 GND 15 ND 4 NC 16 Hot_Plug_detect 5 NC 17 Data0- 6 DDC_CLK 18 Data0+ 7 DDC_DAT 19 GND 8 NC 20 NC 9 Data1- 21 NC 10 Data1+ 22 GND 11 GND 23 CLK+ C5 Note: Supports Single-Link only! 12 NC 24 CLK- C5 GND C3 Blue (DVI-I) C1 Red (DVI-I) C4 H-Sync (DVI-I) C2 Green (DVI-I)
a TechNotes D343x-S V0.2 Page 20 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.12 DisplayPort V1.2 Connector
Pin Signal Pin Signal 1 Link0+ 11 GND 19 1 2 Link0- 12 Link1+ 3 GND 13 Link1- 20 2 4 Link2+ 14 GND 5 Link2- 15 Link3+ 6 GND 16 Link3- 7 DVI dongle detect / (GND 17 GND / (CEC for HDMI (N/A)) (N/A)) 8 AUX+ 18 GND 9 AUX- 19 Hotplug detect 10 GND (Return) 20 P3V3P
a TechNotes D343x-S V0.2 Page 21 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.13 Embedded DisplayPort Connector
Pi Signal Assignment Comment Pi Signal Assignment Comment n1 NC n16 LCD GND 2 GND 17 Hotplug detect 3 Link1- 18 Backl. GND Pin 1 4 Link1+ 19 Backl. GND Pin 30
5 GND 20 Backl. GND 6 Link0- 21 Backl. GND 7 Link0+ 22 Backl enable activ high 8 GND 23 Backl PWM / Dimm 9 AUX+ 24 NC 10 AUX- 25 NC 11 GND 26 Backl 12V 12 LCD VCC 27 Backl 12V 3,3V or 5V 13 LCD VCC 28 Backl 12V 14 NC 29 Backl 12V 15 LCD GND 30 NC
Note: Connector type:
Onboard: I-PEX: 20455-030E-12 (or compatible) eDP Cable (mating housing): I-PEX: 20453-030T-11 (or compatible) Cable requires 1:30 connection (pin 1 to pin 30, pin2 to pin29 etc.)
a TechNotes D343x-S V0.2 Page 22 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.14 Serial ATA Connector
Pin Signal Pin Signal 1 GND 2 Transmit data positive 3 Transmit data negative 4 GND 5 Receive data negative 6 Receive data positive 1 7 GND
a TechNotes D343x-S V0.2 Page 23 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.15 mSATA Pinout / Mini-PCIe Pinout – Fullsize Pin Signal Assignment Comment Pin Signal Assignment Comment mSATA Mini PCIe mSATA Mini PCIe 1 NC WAKE# 27 GND 2 +3.3V +3.3V STBY 28 +1.5V 3 NC 29 GND 4 GND 30 NC 5 NC 31 SATA RX- PCIe RX- Fullsize socket can be used for mSATA (D3433 only!) 6 +1.5V 32 NC or Mini-PCIe (D3433 and D3434) and supports auto 7 NC 33 SATA RX+ PCIe RX+ detection mode. 8 NC 34 GND 9 GND 35 GND (D3433: Mode also selectable via BIOS Setup) 10 NC 36 USB Data negative selectable by BIOS 11 RSVD REFCLK- 37 GND 12 NC 38 USB Data positive selectable by BIOS NC: pin not connected to mainboard 13 RSVD REFCLK+ 39 +3.3V +3.3V STBY 14 NC 40 GND RSVD: pin reserved, connected on mainboard 15 GND 41 +3.3V +3.3V STBY 16 RSVD 42 NC 17 NC 43 GND 18 GND 44 NC 19 NC 45 NC
20 EN_WLAN for PCIe miniCard 46 NC 21 GND 47 NC 22 NC PERST# 48 +1.5V 23 SATA TX+ PCIe TX+ 49 NC 24 +3.3V +3.3V STBY 50 GND 25 SATA TX- PCIe TX- 51 MSATA Present low 26 GND 52 +3.3V +3.3V STBY
a TechNotes D343x-S V0.2 Page 24 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
fInterfaces & Connectors 3.16 mSATA / Mini-PCIe BIOS Setup Options
Mini-PCIe Card Mode (only for D3433-S):
The Halsize / Fullsize socket always supports Mini-PCI Express, mSATA and USB 2.0.
The socket can be configured as: - Standard SATA mode - [Disabled] - MiniCard auto detection – [Auto] - Mini SATA mode – [mSATA] - Mini PCIe mode – [mPCIe] (BIOS Setup option; default = auto).
Note: BIOS Setup option “WLAN” (for D3433-S and D3434) This option can be used to enable/disable Mini-PCIe WLAN modules. (BIOS Setup option; default = Enabled).
a TechNotes D343x-S V0.2 Page 25 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.17 m-SATA / Mini-PCIe Socket Assembly Note
Solder nut for Halfsize Minicard Solder nut for Fullsize Minicard Module Assembly Kit (included in mainboard shipment) contains 1metal spacers and 1 mounting screws. (mounting screw)
Mandatory torque for mounting screws: 0.25Nm +/- 0.05Nm
Max. torque must never be exceeded, otherwise the mainboard (solder nuts) may be damaged.
Note: Damaged solder nuts are not (spacer) covered by any warranty!
a TechNotes D343x-S V0.2 Page 26 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.18 M.2 (Key M) – 2242 & 2260
D3433-S: M.2 cards with SATA or PCIe are supported. PCIe is connected via 2lanes. D3434-S: M.2 SATA only supported.
a TechNotes D343x-S V0.2 Page 27 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.19 M.2 Socket Assembly Note
Solder nut for Solder nut for M.2 2260 M.2 2242 Module Assembly Kit (included in mainboard shipment) contains 1metal spacer nut and 1 mounting screw (M3 x 3.5mm ,bolt head ø = 4.5mm). (mounting screw)
Mandatory torque for mounting M3 screw: 0.4Nm +/- 0.05Nm
Mandatory torque for mounting spacer nut: 0.6Nm +/- 0.05Nm
Max. torque must never be exceeded, (spacer nut) otherwise the mainboard (solder nuts) may be damaged.
Note: Damaged solder nuts are not covered by any warranty!
a TechNotes D343x-S V0.2 Page 28 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.20 Possible configurations for M.2 & Minicard –Modules Configuration Solder nut for example: M.2 2260 Solder nut for Minicard M.2 2242 Module Minicard Solder nut for Fullfsize Halfsize M.2 2242
Solder nut for Minicard Fullfsize
Important Note: Possible configurations: 1. Minicard fullsize + M.2 - 2242, 2. Minicard Halfsize + M.2 – 2260, 3. Minicard Halfsize + M.2 – 2242; Minicard Fullsize + M.2 – 2260: Not supported!
a TechNotes D343x-S V0.2 Page 29 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
2
Interfaces & Connectors
3.21 PCIe x16 Slot Configuration for Riser cards (only supported for D3433-S)
The PCIe x16 Slot (PEG) is compatible for riser cards up to 3 PCIe slots.
The PCIe x16 Slot (PEG) can be configured for: - Single PCIe x16 Slot usage - [PEG] - Riser card with 2x PCIe x8 Slot usage – [Riser] - Riser card with 1x PCIe x8 and 2x PCIe x4 Slot usage – [Riser] (BIOS Setup option; default = PEG).
a TechNotes D343x-S V0.2 Page 30 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors
3.22 Fan Connectors
Pin Signal Pin 1 1 GND 2 12V Note: 3 FAN Sense Fans must never be attached or 4 FAN PWM removed while the system is powered. Mainboard may be damaged! Fan speed control is supported for 4 pin (PWM) fans. Fan3 can be changed from 4-pin mode to 3-pin controlled mode via BIOS Setup. 3-pin fans (voltage controlled) connected to Fan3 connector will always operate at full speed resp. 12V supply voltage!
Fan1 current: max. 2A continuous / 4A peak
Fan3 current: max. 1,2A
a TechNotes D343x-S V0.2 Page 31 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors 3.23 Rear Audio / Frontpanel Audio Connector
Frontpanel Audio: High Definition Mode
Pin Signal Pin Signal 1 HDA Port 1 Left 2 Analog GND 3 HDA Port 1 Right 4 FP Presence Detect 5 HDA Port 2 Right 6 Jack Sense Port 1 7 Jack Sense common 8 Key 9 HDA Port 2 Left 10 Jack Sense Port 2
Frontpanel Audio: Legacy Mode (AC97)
Pin Signal Pin Signal Note: Front audio operating 1 Mic Left 2 Analog GND mode (High Definition Audio 3 Mic Right 4 reserved or Legacy Audio) selectable in 5 Headphone out Right 6 reserved BIOS Setup 7 Analog GND 8 Key 9 Headphone out Left 10 reserved
Note: In case of using this connector in AC97 = Legacy mode (BIOS Setting) take care for pin 7. This pin is tied to GND. HP_ON# signaling on this pin is not supported.
a TechNotes D343x-S V0.2 Page 32 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors Rear Audio / Frontpanel Audio Connector
Rear Audio Connectors
Pin A Pin Signal Line IN (light blue) A Line input
Pin A Pin Signal Headphone OUT (lime) A Headphone output
Electrical input characteristics
Line: Stereo max. 1,2Vrms (Gain=0dB) input voltage
Electrical output characteristics
Headphone: Stereo max. 1,2 Vrms output voltage at 32Ohm load System Speaker (via frontpanel connector): Mono, typ. 2W (RMS) at 4Ohm load
Mute Topology
When an outPut device (HeadPhone, HifiAmp...) is attached to an output jack, the following mute topology is required: FrontOut mutes RearOut and MonoOut RearOut mutes MonoOut (frontpanel system speaker)
Remark: System beeps are only audible via the internal (frontpanel) system speaker. System beeps are also audible on the internal speaker if an external device is plugged in.
a TechNotes D343x-S V0.2 Page 33 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors
3.24 S/PDIF Connector
Pin 1 Pin Signal 1 VCC 2 SPDIF out 3 GND
Note: Standard connector bracket should directly connect to SPDIF out and GND pins (no signal converter required)
(Sample S/PDIF connector bracket)
a TechNotes D343x-S V0.2 Page 34 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors 3.25 GPIO (Feature Connector) Feature Connector: CompuPack R-DRK2-20-S3-SMT (Note: Any 2mm pitch ribbon cable standard parts can be used)
1 GPI/O_0 GPI/O_1 2 3 GPI/O_2 GPI/O_3 4 5 GPI/O_4 GPI/O_5 6 2 1 7 GPI/O_6 GPI/O_7 8 9 VCC_3.3V GND 10 11 VCC_3.3V VCC_5Vaux 12 13 EN WLAN H (Input) GND 14 15 WLAN LED+ (Output ~5mA) GND 16 17 GND VCC_5V 18 (preliminary) 19 VCC_12V VCC_12V 20
Note: Current max. 1.5 A per power pin! Parameter Range GPI/O Input Low Voltage -0.5V … 0.8V GPIO access is provided via the SM-Bus controller PCA9554A GPI/O Input High Voltage 2V … 3.3V ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/ GPI/O Output Low Voltage max. 0.7V D343x-S_Mini-ITX/Documentation/Specification/GPIO_Chip_PCA9554a.pdf Note: SM-Bus address: 0x78h (8-bit) GPI/O Output High Voltage min. 2.5V
Note: max. load per GPI/O pin: 10mA For Windows OS, the FTS BMC API provides easy access to the GPIO: (overall current for all GPI/O pins must be < 85mA) ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/ Each GPI/O pin has an integrated serial resistor of 150 Ohm D343x-S_Mini-ITX/IndustrialTools_D343x-S/
a TechNotes D343x-S V0.2 Page 35 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors
3.26 Power Supply Connector (Multirail)
Pin 13 Pin 1 Pin Signal Pin Signal 13 + 3.3V (P3V3P) 1 + 3.3V (P3V3P) 14 - 12V (P12VN) 2 + 3.3V (P3V3P) 15 GND 3 GND 16 PS on (low asserted) 4 + 5V (VCC) 17 GND 5 GND 18 GND 6 + 5V (VCC) 19 GND 7 GND 20 NC 8 Powergood (high asserted) 21 + 5V (VCC) 9 + 5V Auxiliary (VCC Aux) 22 + 5V (VCC) 10 + 12V (P12VP) 23 + 5V (VCC) 11 + 12V (P12VP) 24 GND 12 + 3.3V (P3V3P)
3.27 Additional Power Supply Connector (12V for Processor)
Pin Signal Pin Signal Pin 3 Pin 1 3 + 12V 1 GND 4 + 12V 2 GND
a TechNotes D343x-S V0.2 Page 36 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors
3.28 Power Supply Connectors (ATX Multirail or Single 12V Operation)
3.28.1 ATX Multirail Operation Important Note:
If the Power Supply is changed from Multirail to single 12V or vice versa, make sure to disconnect the mainboard from any power at least for 10 minutes!
(24 pin ATX connector)
2)Requirement for ATX Multirail operation:
Operational state from the main PSU is off. The mainboard checks
(4 pin 12V connector for CPU power) if PIN10 and PIN11 = 0V & PIN 9 = 5V 24 pin ATX connector: 1) Pin 14 (-12V) and pin 20 (-5V) are not required only then the main PSU starts and the 2) Pin 9, Pin 10 & Pin11 are responsible for operational state mainboard is in ATX Multirail operating mode.
a TechNotes D343x-S V0.2 Page 37 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors 3.28.2 Single 12V Operation
Important Note (Single 12V mode):
The “output” pins (3.3Vout, 5Vout, 12Vout) provide power for drives or extra devices.
Maximum “output” power ratings:
(24 pin ATX connector) +3.3Vout: max. 4A = combined output current of 3.3V PCIe x16 and 3.3Vout pins (1, 2, 12, 13)
+5Vout: max. 9A = combined output current of all USB ports and +5Vout pins (4, 6, 21, 22, 23)
+12V : max. 6A out depends on output power of single
12V PSU! (12V = pin 20) (4 pin 12V connector for CPU power) out
For single 12V operation both connectors 24 pin and 4 pin are required! 2)Requirement for Single 12V operation: 24 pin ATX connector: IF PIN10 and PIN11 = 12V 1) Pin 8, 9, 14, 16 (NC) must NOT be used in single 12V mode! & 2) Pin 9, Pin 10 & Pin 11 are responsible for the operating mode PIN 9 = 0V
only then the mainboard is in Single 12V operating mode.
a TechNotes D343x-S V0.2 Page 38 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors 3.28.3 Single 12V Operation – Config
Important Note: Sample supply cabling for single 12V configuration: e.g. processor 65W, additional graphics card, several SATA drives The switching / mode detection between ATX- and single 12V- operating mode is different to the mainboard D3243-S!!! All four +12Vin pins must be connected to the +12V supply source. Both GND pins (4-pin conn.) & two GND pins (24-pin connector) must be connected to the supply source.
+12V
GND
(Single 12V PSU)
Note: Each single pin of both connectors is capable of max. 8A! All pins of the 4-pin connector must be used due to peak current in Turbo Mode.
a TechNotes D343x-S V0.2 Page 39 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
3
Interfaces & Connectors 3.29 Chassis Intrusion
Pin Signal Pin 1 1 GND 2 Case open (low asserted) 3 Intrusion switch present (low asserted)
Note: The intrusion supervision feature needs to be enabled in BIOS Setup first (Menu „Security“ „Cabinet Monitoring“). This BIOS option is only available if pin 3 („Intrusion Switch Present“) is connected to GND!
Note: Chassis intrusion is active even if the system is switched off (S5 state) or disconnected from mains power. The intrusion event is monitored by the chipset (PCH) and stored in the BIOS Eventlog during the next Boot. A timestamp (Boot date/time) will be added then. Note: This timestamp does not represent date/time of the intrusion event! If a Supervisor Password is enabled in BIOS Setup, the system will stop during BIOS POST if an intrusion event has been detected. In order to continue, the Supervisor Password must be entered to confirm the intrusion event.
The intrusion status can be easily monitored by using the BMCAPI (Windows): ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/IndustrialTools_D343x-S/
a TechNotes D343x-S V0.2 Page 40 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
4 System Monitoring
- Temperature Sensors and Fans - SystemGuard: Fan / Temperature Monitor - SilentFanConfig-Manager - Temperature Reference Points - BMC – BIOS Default Settings
a TechNotes D343x-S V0.2 Page 41 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring
4.1 D343x-S: Temperature Sensors and Fan Connectors (preliminary)
Fan 3 (PWM or 3-pin) 2) 3)
Sensor “PCH” Sensor “Ambient”
Sensor “CoreRegulator” Sensor “Memory”
Sensor “Processor”
Processor (Fan1; PWM) 1) Sensor “PCIe Graphics”
1) 2A continuous / 4A peak current
2) 1,2A continuous
3) FAN 3: PWM or 3-Wire Selectable via BIOS Setup Note: Do not attach more than one fan per connector! Default = PWM) Remove or connect fans only when unit is powered off!
a TechNotes D343x-S V0.2 Page 42 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring
4.2 SystemGuard
System Monitoring Tool: • Visualize processor and sensor temperature data
• Display current speed for all attached fans
• User can configure fan aging control (menu “Special”)
• User can configure system watchdog (menu “Special”)
User can adjust system behaviour via “Silent PC / Performance PC” slider by forced processor throttling
a TechNotes D343x-S V0.2 Page 43 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring
4.3 SystemGuard - Details
Temperature Sensors Processor Sensor 1)
Sensor PCIe Graphics
Ambient Temperature
Core Voltage Regualtor Sensor
Memory Sensor
PCH Sensor
Sensor / Fan Matrix Indicates which sensor influences the specific fan speed Note: Characteristics for FAN1 is always dependent on the CPU temperature – fully controlled by the system BIOS. Due to safety reasons the influence of the CPU sensor for FAN1 cannot be disabled!
(Note: Sample screenshot only; data may differ for specific mainboard model)
1) Note: The temperature value shown for the processor (digital „PECI“ measurement =Platform Environment Control Interface) does NOT provide the absolute processor temperature, but it is a calculated value based on the relative PECI data.
a TechNotes D343x-S V0.2 Page 44 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring
4.4 SilentFanConfigManager – Customize System Monitoring Settings
Windows-based System Management Configuration Tool ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/IndustrialTools_D343x-S/SilentFanConfig-Manager/
1. Windows-based configuration tool (SilentFanConfig) to create customized system monitoring settings like minimum fan speed and temperature sensor influence. These customized settings are stored in a specific “SMCO” flash file.
2. DOS-based tool “SMCO” to flash the customized system monitoring settings (SMCO file) to the system BIOS of the target unit.
SilentFanConfig-Tool: SMCO-Tool SilentFanConfig-Tool + Create specific system SMCO Flash File Flash SMCO file to SMCO-Tool = monitoring settings mainboard BIOS SilentFanConfigManager
(any Windows-based PC) (each unit in production)
Note: New settings are written permanently to system BIOS.
Any BIOS update will not reset the new settings
SilentFanConfig V1.82.0 or higher required for D343x-S
Please see documentation in ZIP file (link below) for further details. ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/IndustrialTools_D343x-S/
a TechNotes D343x-S V0.2 Page 45 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring 4.5 Components for continous 24/7 operation @ +60°C
Operating Conditions: 8-layer PCB for improved Circulating air signal quality within full (mainboard) max. 60°C operating temperature range Usage 24h / 7 days Extra Heatsink on PCH Oscillator with enhanced operating temperature range High Efficiency Processor Core Voltage Regulator All onboard electrolyte for reduced thermal capacitors: Polymer type only dissipation loss (= solid electrolyte)
Note: Power Consumption PCH P max ~ 4.1W COM Driver with enhanced P idle ~ 0.7W operating temperature range
Capacitor Endurance Time Lx = effective endurance time Lo = endurance time @ 105°C Solid Electrolyte: (e.g. 2.000hrs) to = 105°C tx = capacitor surface temperature Fluid Electrolyte: (e.g. 68°C)
a TechNotes D343x-S V0.2 Page 46 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring
4.6 Capacitor Endurance Time Comparison
a TechNotes D343x-S V0.2 Page 47 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring
4.7 Temperature Reference Points D343x-S Operating Conditions: Circulating air TPM max. 70°C All capacitors max. 70°C (mainboard) max. 60°C Usage 24h / 7 days
PCH max. 95°C (chip surface)
Qscillator max. 70°C
Inductor max. 100°C
Power MOS-FETs / MOS-FET Drivers max. 100°C Battery max. 60/70°C 1)
Audio Codec max. 75°C
1) Note: Battery operation is specified in temperature range up to 60°C. Operation between 60°C and 70°C may result in: - Higher self discharge rate - Decline of specified characteristics Reference Point Limit Temperatures (Component Surface) must not be exceeded! - Danger of leakage increases
a TechNotes D343x-S V0.2 Page 48 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring
4.8 Temperature Reference Points D343x-S (rear) Operating Conditions: Quartz max. 70°C Circulating air (mainboard) max. 60°C Usage 24h / 7 days
LVDS Converter max. 85°C LAN max. 85°C COM Driver max. 70°C
SP-Caps max. 95°C Note: Humidity should not exceed 75% at 60°C
COM Driver max. 70°C Super I/O max. 70°C
Quartz max. 70°C
Reference Point Limit Temperatures (Component Surface) must not be exceeded!
a TechNotes D343x-S V0.2 Page 49 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
4
System Monitoring
4.9 BMC – BIOS Default Settings D343x-S
The default system monitoring settings like fan speed, sensor influence, and Alert temperatures are fixed by the system BIOS. All relevant settings can be customized by system builders via the SilentFanConfig-Manager tool kit.
Sensors PECI (Processor) PCIe Graphics Ambient Core regulator Memory PCH Fan1 (CPU) X X Fan3 X X X X X X
“X” indicates that this specific sensor influences the speed of this specific fan
StartUp 1) FullSpeed 2) Alert 3) Note These settings are fixed by the BIOS (depends on the PECI (Processor) n.a. n.a. n.a. individual installed processor) and cannot be changed via SilentFanConfig-Manager. Ambient 45°C 60°C 68°C Core Regulator 50°C 75°C 80°C These settings are implemented for the current Memory 40°C 60°C 65°C BIOS version and may be changed for upcoming PCH 50°C 60°C 70°C BIOS versions! Default minimum fan speed = 30% (all fans). PCIe Graphics 40°C 60°C 65°C
1) If the sensor temperature is below “StartUp” the fan rotates a its defined minimum fan speed 2) Between “StartUp” and “FullSpeed” the fan speed increases linear 3) If the sensor temperature achieves “Alert”, the system can provide a warning (e.g. via SystemGuard tool)
a TechNotes D343x-S V0.2 Page 50 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
5 Power Supply 5.1 ATX Power Supply Connectors for ATX (Multirail) Power Supply
(2) (1) 24 pin connector (ATX layout) (1) (3) (2) 4 pin connector (+12V, GND)
Note: The +12V supply (up to 12A) for processor and chipset is provided via the 4 pin connector! Onboard voltage regulators convert the +12V input power to the appropriate processor / chipset supply voltages.
(3) Processor Core Voltage Regulator: High Efficiency design for enhanced power saving and less thermal dissipation loss.
Power Supply Requirements for onboard components (worst case incl. processor & memory; w/o USB devices; w/o PCIe cards, w/o M.2 / mSATA / SATA drives) Mainboard Source 1) Voltage Min. PS Max.Voltage Max. Mainboard Capacitive Load Tolerance Current Load + 12V 0.05A ± 5 % 1.300µF 8A/12A 2) - 12V 0A -- not used ATX Power + 5V 0.2A ± 5 % 900µF 3A Supply + 3.3V 0A ± 5 % 350µF 0.5A + 5Vaux 0A +5 % / -3% 330µF 0.5A
2) The power supply must support the minimum load 12V only PSU +12V 0A ± 5 % 1.300µF 8A/12A 1) ATX PSU or 12V only DC Supply conditions as mentioned in the left chart. 2) Max. Cont. Current = 8A; max. Surge Current = 10A (< 100sec) / 12A (< 10ms)
a TechNotes D343x-S V0.2 Page 51 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
Power Supply
5.2 Typcial Power Consumption (to be added soon)
a TechNotes D343x-S V0.2 Page 52 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
6 USB Implementation 6.1 USB Ports & USB Power Fuses (D3433-S)
D3433-S: There is one USB controller (xHCI) for all USB ports USB Ports: #8 Max. Current Description USB Port # Common Fuse Note per Port USB 3.0 #2 / #3 2A 900mA Frontpanel USB 2.0 #13 for internal Internal #6 / #7 500mA devices 1) #6 / #7 2A USB 3.0 for internal #2 / #3 #13 900mA Stick Socket 1) devices 1) USB 3.0 Rear (right) #0 / #1 2A 900mA (USB/USB/LAN) USB 3.0 Rear (left) #4 / #5 2A 900mA (USB/USB/LAN) USB 2.0 Rear #9 / #10 / #12 / #11 2A 500mA USB 2.0 for internal #8 (not fused) 500mA mSATA / mPCIe 1) devices 1)
1) Note: These “internal” ports do not provide “Windows Device Eject”
a TechNotes D343x-S V0.2 Page 53 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
USB Implementation Rear USB Ports for D3433-S:
#11 #5 #1 #12
#10
#9
#4 #0
a TechNotes D343x-S V0.2 Page 54 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
USB Implementation
6.2 USB Ports & USB Power Fuses (D3434-S)
D3434-S: There is one USB controller (xHCI) for all USB ports USB Ports:
#8 Max. Current Description USB Port # Common Fuse Note per Port USB 3.0 #2 / #3 2A 900mA Frontpanel USB 2.0 for internal #6 / #7 2A 500mA Internal devices 1) USB 3.0 Rear #6 / #7 (right) #0 / #1 2A 900mA (USB/USB/LAN) #2 / #3 USB 2.0 Rear (left) #4 / #5 2A 500mA (USB/USB/LAN) USB 2.0 Rear #9 2A 500mA USB 2.0 for internal #8 (not fused) 500mA mPCIe 1) devices 1)
1) Note: These “internal” ports do not provide “Windows Device Eject”
a TechNotes D343x-S V0.2 Page 55 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
USB Implementation Rear USB Ports for D3434-S:
#5 #1
#9 #4 #0
a TechNotes D343x-S V0.2 Page 56 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
7 Display Options 7.1 Summary: Video Output Options D343x-S
Up to three independent displays supported (D3434-S: max. two displays) Supports Clone Mode, Extended Desktop and Collage Mode (combine 2 or 3 displays to one screen) Support of 4K display technology via DisplayPort output DisplayPort is compatible with DP to HDMI – adapter, DP to DVI – adapter and DP to VGA – adapter DVI-D is compatible with DVI to HDMI – adapter and (active) DVI to VGA - adapter Second DisplayPort can be used as DP, eDP or LVDS (via onboard DP to LVDS converter) eDP and LVDS can be used simultanously
a TechNotes D343x-S V0.2 Page 57 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
Display Options
eDP (2 lanes)
eDP: max. 1920 x 1200 @ 60Hz (18, 24-bit)
LVDS 24bit 8max. 1920 x 1200)
DVI-D
DVI-D: max. 1920 x 1200 @ 60Hz
1 x or 2 x Displayport V1.2
DP: max. 4096 x 2304 @ 60 Hz
a TechNotes D343x-S V0.2 Page 58 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
Display Options 7.2 LVDS Display & Backlight Inverter
Integrated Backlight, powered by Inverter
Backlight Inverter
a TechNotes D343x-S V0.2 Page 59 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
5
Display Options 7.3 LVDS Connector Details
LVDS Connector: Hirose DF13-40 (or compatible)
PIN SIGNAL SIGNAL PIN 2 Ground Ground 1 40. 2. 4 LVDS_H3+ (EVEN_3+) LVDS_L3+ (ODD_3+) 3 39. 1. 6 LVDS_H3- (EVEN_3-) LVDS_L3- (ODD_3-) 5 8 Ground Ground 7 10 LVDS_H2+ (EVEN_2+) LVDS_L2+ (ODD_2+) 9 12 LVDS_H2- (EVEN_2-) LVDS_L2- (ODD_2-) 11 14 Ground Ground 13 16 LVDS_H1+ (EVEN_1+) LVDS_L1+ (ODD_1+) 15 18 LVDS_H1- (EVEN_1-) LVDS_L1- (ODD_1-) 17 LVDS operating voltage selector jumper 20 Ground Ground 19 22 LVDS_H0+ (EVEN_0+) LVDS_L0+ (ODD_0+) 21 24 LVDS_H0- (EVEN_0-) LVDS_L0- (ODD_0-) 23 26 Ground Ground 25 28 LVDS_CLK_H+ (CLK_EVEN+) LVDS_CLK_L+ (CLK_ODD+) 27 30 LVDS_CLKH- (CLK_EVEN-) LVDS_CLK_L- (CLK_ODD-) 29 32 Ground Ground 31 34 DDC-Data DDC-Clock 33 36 LCD-Power 1) LCD-Power 1) 35 38 Ground LCD-Power 1) 37 40 LCD_Power_Enable Ground 39 1) selectable via Jumper
Note: LVDS pinning is compatible to D2703-S / D2963-S / D3003-S / D3313-S / D3243-S D3433-S / D3434-S
a TechNotes D343x-S V0.2 Page 60 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options 7.4 Backlight Inverter Connector Details Backlight Inverter Connector: JST PHR-8
1. 8.
LVDS Backlight Brightness Control Jumper Backlight Brightness Control: (Select analog or PWM output) Provides a variable DC voltage between 0V and 4V via an RC filter (10kOhm / 20uF; buffered output). Alternatively a PWM control is available, please see related jumper setting. Basically the brightness level can be selected by BIOS Setup, but it is also accessible from Windows OS.
If this control signal is used, the system integrator is responsible for the implementation of a backlight converter that fits to the control output voltage range.
Backlight On/Off Control: Active High, 3.3V Note: Polarity can be changed via BIOS Setup
a TechNotes D343x-S V0.2 Page 61 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options 7.5 LVDS Timing & Screen Resolution
There are 9 default LVDS settings available BIOS Setup – Advanced –LVDS Config Select
Note: Option 10 (LVDS adjusted Parameters) becomes visible after running the “LVDS Tool” for implementing customized LVDS settings once.
Important note: “Non-EDID Support” must be set to
a TechNotes D343x-S V0.2 Page 62 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options LVDS Timing & Screen Resolution
LVDS Mode: The correct mode must be set for the attached LVDS panel.
Note: This setting is also required if customized LVDS timings are implemented (LVDS tool)!
LVDS Brightness: Set the level for the „Backlight Brightness Pin“. Typical voltage level (analog mode) resp. PWM level:
BIOS-Setting Voltage Level / PWM Level (prelim.) 0 0.1V / 0.4% 255 4.1V / 100%
Preliminary (not yet implemented): The LVDS brightness level can be adjusted in BIOS Setup or via Windows 7 / Windows 8.1 Mobility Center (
a TechNotes D343x-S V0.2 Page 63 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options LVDS Timing & Screen Resolution
POST Screen Mode: Default setting = Graphic Mode (800 x 600).
For panels < 800 x 600 mode could be changed to
a TechNotes D343x-S V0.2 Page 64 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options 7.6 LVDS Tool
The LVDS tool (DOS-based) allows to flash specific LVDS settings to the system BIOS of D343x-S.
The LVDS tool needs a panel-specific EDID configuration file based on the spec data of the LVDS panel.
Note: Sample configuration EDID files are available in the LVDS Tool kit. For adjusting EDID files the “Phoenix EDID tool” Is required (see link below).
(Sample screen message after running LVDS tool)
Download-Link for LVDS Tool: ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/IndustrialTools_D343x-S/LVDS-Tool/ LVDS tool ≥ V2.2.1 must be used to implement customized LVDS settings
Note: The onboard LVDS converter switches automatically between single channel and dual channel mode. The reference resolution is 1366 x 800 pixels. If H > 1366 or V > 800, the scaler switches to dual channel mode. Otherwise, LVDS will operate in single channel mode. The scaler supports clock rates up to 105Mhz; LVDS displays with clock rates > 105Mhz are not supported
a TechNotes D343x-S V0.2 Page 65 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options 7.7 LVDS – Influence on Graphics Output (prelim.)
When LVDS support is enabled in BIOS Setup, this has some effect on the support of the other graphics output ports (DVI-D, DisplayPort). Furthermore, the setting “Secure Boot” also influences the supported graphics output modes.
a TechNotes D343x-S V0.2 Page 66 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options 7.8 LVDS Cabling Reference
Sample cabling diagrams for following LVDS displays & related inverters are available:
Display Size TFT Pixel Inverter 10.4" NEC NL6448BC33-63D 640 x 480 NEC 104PW201 12.1" AUO G121SN01-V0 800 x 600 Green-C&C GH093A-ROHS 12.1" LG-Philips LB121S03-TL01 800 x 600 Green-C&C GH001HB-ROHS 15" Sharp LQ150X1LW71N 1024 x 768 TDK CXA-0349 15" AUO G150XG01V0 1024 x 768 Green-C&C GH001A-ROHS 17" AUO M170EG01-VD 1280 x 1024 Green-C&C GH053A-ROHS 19" Sharp LQ190E1LW01 1280 x 1024 Power Systems PS-DA0412-05 19" AUO M190EG01 1280 x 1024 GH053(A1)-ROHS
ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/Documentation/LVDS_Cabling-Samples/
a TechNotes D343x-S V0.2 Page 67 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options 7.9 LVDS Sample Cabling for AuO-G150
a TechNotes D343x-S V0.2 Page 68 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options 7.10 Embedded DisplayPort (prelim.)
Cable requires 1:30 connection (pin 1 to pin 30, pin2 to pin29 etc.)
Pin 30 Pin 1 Pin 1 Pin 30
a TechNotes D343x-S V0.2 Page 69 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
6
Display Options 7.11 Embedded Display Port Power
Pin 1
eDP-Power Jumper
Pin Signal Pin Signal 1 P5VP 2 VCC 3 P3V3P
With this jumper you can select the level of the power for embedded display port connector.
Note: The default state is VCC = 3,3V
a TechNotes D343x-S V0.2 Page 70 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
8 Operating System Support
- Windows® 7 - Windows® 8.1 - Windows® 10 - Linux
a TechNotes D343x-S V0.2 Page 71 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
Operating System Support
8.1 Support for Windows 7 / Windows 8.1 / Windows 10
• Mainboards D343x-S are designed according to the
Microsoft Guidelines for Windows 7, Windows 8.1 and Windows 10
• MS certified drivers are available via OEM DU-DVD and OEM FTP Server
ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/Drivers_D343x-S/
a TechNotes D343x-S V0.2 Page 72 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
Operating System Support
8.2 Linux Support (to be added soon)
a TechNotes D343x-S V0.2 Page 73 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
9 Mainboard Tools
Common Mainboard Tools
Note: Make sure to not use any DOS memory manager like himem.sys oder emm386!
9.1 BIOS Boot Logo Tool
- Tool to integrate a customized boot logo ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/BootLogo_4_UEFI/
9.2 EditCMOS
- DOS-based production tool to change BIOS settings and freeze customized BIOS settings (= customized default settings) ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/EditCMOS_UEFI/
9.3 OEMIDENT
- Production tool to add MS OEM licence data (SLP1 / SLP2.x / OA3.0) - Add an individual customer serial no / add a chassis asset tag and patch several DMI data - Disable and hide TPM feature in BIOS Setup ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/OEM-Ident/
a TechNotes D343x-S V0.2 Page 74 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
Mainboard Tools
9.4 SystemGuard
- Windows-based tool to monitor temperatures and fan speed of FTS mainboards - Option to configure automatic fan ageing supervision - Provides access to the System Watchdog
ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/SystemGuard/
Note: SystemGuard V4.07 (or higher) required for D3433-S, D3434-S
a TechNotes D343x-S V0.2 Page 75 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
Mainboard Tools
Industrial Tools
9.5 SilentFanConfig-Manager - Windows-based configuration tool to implement customized fan characteristics and temperature parameters. Includes DOS-based tool "SMCO" to flash the configuration file permanently into the system BIOS.
ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/IndustrialTools_D343x-S/Silent FanConfig-Manager/
a TechNotes D343x-S V0.2 Page 76 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
Mainboard Tools
9.6 Windows System-Monitoring API (BMCAPI) - BMC-Management-Controller to access and adjust System Monitoring parameters like fan speed and temperatures. This API also provides access to the mainboard watchdog, the 8Bit GPIO interface and the intrusion feature of the mainboard. ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/IndustrialTools_D343x-S/BMC_ Management-Controller-API/
9.7 Linux System-Monitoring Driver (“LM-Sensors”) To be added soon
- BMC-Management-Controller to access and adjust System Monitoring parameters like fan speed and temperatures. This driver also provides access to the mainboard watchdog.
a TechNotes D343x-S V0.2 Page 77 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
10 Known Issues & Important Notes 10.1 USB 2.0 / MS Windows 7 Skylake provides no longer native USB 2.0 support for MS Windows 7 --> PS/2 keyboard/mouse for OS setup recommended
Note: Intel removed the EHCI USB controller, which is replaced by the xHCI USB controller. MS Windows 7 only provides inbox driver support for EHCI; the xHCI USB device driver must be installed first before any USB port can be used when running MS Windows 7. A BIOS workaround for this USB issue is available from BIOS R1.10.0.
10.2 TPM2.0 / MS Windows 7 All Fujitsu Skylake-based mainboards provide TPM V2.0. as recommended for MS Windows 10.
Win7 (x32/x64) Win7 (x32) Win7 (x64) Win8.x (x32/x64) Win8.x (x32/x64) Win10 (x32/x64) Win10 (x32/x64) legacy UEFI UEFI Legacy UEFI Legacy UEFI TPM 2.0 Support No No YES 1) No YES No YES
1) MS Hotfix required: Update to add support for TPM 2.0 in Windows 7 and Windows Server 2008: https://support.microsoft.com/en-us/kb/2920188
As TPM 2.0 is not supported by MS Windows 7 (except for 64Bit/UEFI), TPM should be disabled in BIOS Setup then
a TechNotes D343x-S V0.2 Page 78 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
11 Miscellaneous 11.1 Battery Lifetime
The typical battery lifetime is designed for 5 years.
This is based on following usage profile:
G3 28% / two days per week (System Off, Power disconnected)
Deep S5/S4/S3 48% / 17 hrs per working day (System Off, Power connected)
S0 24% / 8 hrs per working day (System Working)
On-Temperature (S0): 70°C Off-Temperature (G3, S5/S4/S3): 23°C
Note: If the system is never in G3 mode or if the S0 “working” temperature is lower than 70°C, this may result in much higher battery lifetime.
If the mainboard is just stored (no operating voltage attached), the typical battery lifetime is also 5 years. Due to tolerances of the installed battery, the effective battery lifetime may be in the range of 4.5 years – 6 years
a TechNotes D343x-S V0.2 Page 79 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
7
Miscellaneous 11.2 RealTime Clock (RTC) Accuracy
The onboard realtime clock is approved for an accuracy of +/-30ppm (= max. 75sec deviation per month).
The RTC crystal itself is specified with +/-10ppm (= max. 26 seconds deviation per month). Each year of ageing adds around +/-3ppm on top of this.
a TechNotes D343x-S V0.2 Page 80 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
Miscellaneous 11.3 System Watchdog (WD)
Mainboards provide full BIOS POST-, Operating System Boot-, and Operating System-Runtime watchdog supervision.
Power On Init BIOS POST OS Boot OS running “BIOS POST Watchdog 1)” “BIOS Boot Watchdog 1)” “OS Watchdog” 1) 2)
POST-WD-timeout = 120sec. BOOT-WD-timeout OS-WD-timeout (max. 255 minutes) (fix defined by BMC firmware) (according to BIOS Setup) (according to specific WD software agent)
OS started. If the watchdog has been enabled by BIOS (timeout set to xy minutes in BIOS Setup) it must be switched off or retriggered (continuously) by a specific OS application (=WD software agent), otherwise the system will be reset after xy minutes (= BOOT- WD-timeout) respectively after nn minutes (repetitive OS-WD-timeout).
If the watchdog is enabled in BIOS Setup (timeout set to xy minutes) and the system hangs during OS boot, the system will be reset after xy minutes.
BIOS checks at the end of POST if the watchdog must be switched off (timeout set to 0 in BIOS Setup) or retriggered according to the timeout setting in BIOS Setup (1 - 255 minutes)
BMC initializes watchdog (fixed timeout = 2 minutes; no user setting possible). If the operator runs BIOS Setup the watchdog is set on hold. Additional PCI/PCEe extensions cards that provide an Option ROM may cause a system reset due to BIOS POST watchdog timeout, if the user activates any menu within the Option ROM for more than 2 minutes!
1) Note: All three watchdogs are physical identical, but they are handled from different application levels 2) As the SystemGuard tool offers access to the watchdog it can be used as “WD software agent” to retrigger the watchdog during OS runtime
a TechNotes D343x-S V0.2 Page 81 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
Miscellaneous
System Watchdog (WD)
How to handle the different watchdog levels
BIOS POST Watchdog
o No user interaction possible – POST Watchdog is always enabled!
BIOS Boot Watchdog
o Set Watchdog in BIOS Setup
0 = WD disabled 1 – 255 = WD enabled (timeout = 1 – 255 minutes)
a TechNotes D343x-S V0.2 Page 82 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
Miscellaneous
System Watchdog (WD)
OS Watchdog
o Use “WD software agent” to stop or retrigger the watchdog during OS runtime Note: This “agent” needs to be provided by the customer, dependent on his needs. For easy access to the watchdog functions, the Windows API (BMCAPI) or the related Linux driver (lm-sensors) can be used: ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/IndustrialTools_D343x-S/
o For easy testing, the SystemGuard tool provides access to the OS Watchdog. After enabling the Watchdog, SystemGuard retriggers the WD continuously. In case the system freezes, SystemGuard does no longer provide the retrigger signal and the watchdog resets the system after the timeout. Note: When SystemGuard is closed, the WD is stopped in order to avoid a unwanted system reset!
Menu “Special”: --> Enable WD --> Set timeout to 1 – 8 minutes
a TechNotes D343x-S V0.2 Page 83 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
Miscellaneous 11.4 BIOS Update / BIOS Recovery
BIOS update options
Link to related BIOS files (OEM FTP Server): ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/BIOS_D343x-S/
DOS-based BIOS update (DOS-bootable USB stick)
Required BIOS files:
o EfiFlash.exe (DOS flash tool) o DosFlash.bat (batch file) o Dxxx-y.upd (flash file)
Copy unzipped files to a DOS-bootable USB stick, boot system from stick and run DosFlash.bat
Note: In order to easily create a Free-DOS bootable stick, the Fujitsu BootStick tool can be used: ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/USB-FreeDOS-Bootstick/
Note: Make sure not to use any DOS memory manager like himem.sys or emm386!
a TechNotes D343x-S V0.2 Page 84 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
Miscellaneous BIOS Update / BIOS Recovery
Windows-based BIOS update (Deskflash tool)
Required BIOS file:
o Dxxxx-Sx.R1.x.y.DFI.exe (Windows executable flash tool)
Copy file from FTP (link see above), rename filename.$xe to filename.exe and copy to target system (e.g. Windows desktop). Doubleclick to start BIOS update and follow instructions on the screen.
DOS-based BIOS Recovery (DOS-bootable USB stick)
Required BIOS files:
o EfiFlash.exe (DOS flash tool) o DosFlash.bat (batch file) o Dxxxx-S1.upd (flash file) o Dxxxx-S1.rom --> Important: These files must be located in the root directory of the USB stick!
Copy the *.ROM file (included in the ZIP file) to the root directory of a FAT32 formatted bootable USB stick. Power off the mainboard, insert the USB stick, set the jumper to Recovery Mode (see picture), then turn on the mainboard. You will hear short beeps while the BIOS is recovered. Wait until you hear a series of "long-long-short-short" beeps. Then turn off the mainboard and move the jumper back to the standard position.
The Recovery process can take a few minutes. Note: BIOS Recovery should only be used to repair a corrupted BIOS. All customized data except for OEM SLP data will be reset.
11.5 BIOS/CMOS: Reset Defaults
Set BIOS Setup to Defaults (“Clear CMOS”): Power off system, set Jumper to “Recovery”, power on system and wait until picture appears on screen. Power off again and set jumper to previous position. CMOS settings should now be reset to default mode. (For this procedure no BIOS update/ USB stick is required!).
a TechNotes D343x-S V0.2 Page 85 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
Miscellaneous 11.6 BIOS integrated HW Diagnostic Tool Starting with the D323x mainboards, there is a hardware test module integrated in the system BIOS. In order to run the tool, please select “Diagnostic Program” as boot device and follow the instructions on the screen. This test module analyzes CPU, Memory and HDD.
11.7 BIOS integrated Erase Disk Tool
All Industrial Mainboard include the BIOS tool “EraseDisk” for easy and secure deletion of any data on the harddisk
Detailed information about Erase Disk is available here:
ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D343x-S_Mini-ITX/Documentation/PF_EraseDisk_e.pdf
a TechNotes D343x-S V0.2 Page 86 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
Miscellaneous 11.8 Power indicator
a TechNotes D343x-S V0.2 Page 87 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8
TechNotes D307x-S V1.1 54 Copyright 2011 FUJITSU
a TechNotes D343x-S V0.2 Page 88 of 88 http://www.fujitsu.com/fts/products/computing/pc/accessories/mainboards Page g mainboards e
8