Economic Recovery of Selenium by Flotation from Sandstone Ores Of

Total Page:16

File Type:pdf, Size:1020Kb

Economic Recovery of Selenium by Flotation from Sandstone Ores Of Circular 58 Economic Recovery of Selenium by Flotation From Sandstone Ores of New Mexico by Roshan B. Bhappu NEW MEXICO INSTITUTE OF MINING AND TECHNOLOGY E J. Workman, President STATE BUREAU OF MINES AND MINERAL RESOURCES A. J. Thompson, Director Circular 58 ECONOMIC RECOVERY OF SELENIUM BY FLOTATION FROM SANDSTONE ORES OF NEW MEXICO by ROSHAN B. BHAPPU 1961 STATE BUREAU OF MINES & MINERAL RESOURCES NEW MEXICO INSTITUTE OF MINING & TECHNOLOGY CAMPUS STATION SOCORRO, NEW MEXICO ABSTRACT Investigation has shown that the selenium-bearing sandstone ores from the Morrison and Galisteo formations of New Mexico are amenable to simple froth-flotation procedures. The common flotation reagents used are soda ash, sodium silicate, a neutral oil (kerosene), a xanthate, and a frother. Conditioning of the pulp prior to flotation plays an important role in the proc- ess, especially if the sandstone contains excessive amounts of slimy clays and shale s. Under optimum conditions, the selenium flotation is rapid and selective; selenium recovery above 85 percent is possible; and an acceptable grade of concentrates above 4 percent is obtainable. From the economic viewpoint, flotation recovery of selenium ap- pears attractive. The cutoff grades for the profitable recovery of selenium as the major ore constituent are 0.12 and 0. 04 percent for underground and open-pit mining operations respectively. On the other hand, when selenium is recovered as a byproduct of some other mining operation, such as mining for uranium, the cutoff grade is only 0. 01 percent. INTRODUCTION If an element could be said to have "magical properties," it is prob- able that high-purity selenium would come closest to fitting this description. Despite this tribute, selenium remains a metal with an unimpressive back- ground and an unknown and unpredictable future. Although selenium is widely distributed in the earth's crust, the known deposits are either so small or of such low grade that they cannot be processed economically for selenium alone. Many years ago the sole source of selenium was thought to be the flue dusts from metallurgical processes uti- lizing sulfur ores; today, however, recovery from this source is virtually nonexistent. The anode slimes from electrolytic copper refineries are now providing the source of most of the world's selenium, and its production is centered at such refineries in the industrialized nations of the world. The most serious problem confronting the selenium industry is its dependence on the refining of electrolytic copper, for this byproduct source is not sufficiently flexible to permit a normal supply-demand balance. The remedy, it is apparent, lies in the development of alternate sources of selenium on an economic and commercial scale. Efforts, however, to find such sources, even under a price inducement nearly double that in effect today, have not been successful. 1 Most of the growth in selenium output has been within the last dec- ade. In view of the relative immaturity of this segment of the mining industry, it is not surprising that so little is known of the geology of selenium deposits and that only limited progress has been made in developing techniques in mineral beneficiation and metallurgy especially adapted to the production of this metal. Although the chemical and physical properties of selenium have been studied extensively and are fully covered in the literature, numerous problems of application to potential new uses remain unsolved. The apparent lack of knowledge about selenium goes back to a his- torical attitude of aloofness. The metal had few applications at first and was looked upon as a poisonous contaminant. A program of educational promotion, with a direct appeal to those interested in both the exploitation and utilization of selenium, could eradicate much of the cautious indifference that has ham- pered growth in the use of this metal. Since selenium is a strategic metal in short supply, new sources are being sought by both government and private interests. Although considerable attention has been given to this effort during the last few years, hardly any research has been published that is devoted to the recovery of the small amounts of selenium present in low-grade deposits in which the metal occurs as native selenium or as selenides of copper, silver, lead, mercury, bismuth, thallium, and iron. In recent years, some native selenium (in both the red and gray forms) and selenides, especially iron selenide (ferroselite), reportedly have been found in the sandstones of the Morrison formation in New Mexico. •Sun and Weege (1959) encountered a sample containing considerable native sele- nium, in the course of working on a calibration curve for the determination of selenium by an X-ray spectroscopic method. This sample had been collected from the Marquez mine, operated by Calumet and Hecla, Inc. , near Grants, New Mexico. Similar occurrences in the same area have been reported by other writers and mine operators. Elsewhere, Wilson (1960) and the Dial Exploration Co. , of Albuquerque, New Mexico have discovered an ore body containing some selenium in the Hagan coal basin, in Sandoval County, New Mexico. Samples from New Mexico ores submitted to the State Bureau of Mines and Mineral Resources, and assayed in the Bureau's laboratory, have contained from a trace amount to as high as 0.425 percent selenium. Some of these samples have come from uranium mines in the Grants area and repre- sent mined ore and mill feed for uranium reduction plants. In such cases, the selenium usually is reported as an undesirable impurity and is lost in the tailings. At present, no attempt is being made to recover this waste metal. Owing to recent advances in mining and milling technology, many valuable minor metals and mineralscan be recovered economically even though their total content in the ore may appear to be very low and unworthy of ex- ploitation. At a price of $7 per pound for commercial-grade selenium, it would appear justifiable to investigate the possibility of recovering small amounts of 2 this metal contained in such ore, especially if it occurs along with other valu- able metals and can be recovered as a byproduct. In view of the economic importance of selenium and its presence in some ores from New Mexico, the metallurgical staff of the State Bureau of Mines and MineralResources undertook the present investigation on the recovery of selenium from such ores by froth flotation. This report covers the experimental work carried out on the flotation recovery of selenium from sandstone ore samples from the Morrison formation, near Grants, New Mexico (especially Poison Canyon sandstone), and from samples of selenium ores submitted by the Dial Exploration Co. from its development work on the We Hope mining claims, in Sandoval County, New Mexico. Since many of these ores contain. uranium and molybdenum besides selenium, efforts have been made to develop procedures and flowsheets to in- corporate the recovery of these associated metals as well. Realizing, moreover, the need for rapid, reliable methods for the qualitative (including field tests) and quantitative determination of selenium in ores, the Bureau has spent considerable time on developing such methods in its analytical laboratory. These methods are included in the report for the benefit of prospectors and mine -mill operator s. Since knowledge of the economics of a metal is essential for obtain- ing a clear overall picture of the metal under investigation, efforts were made to include in the first part of the report a brief discussion of topics included under the broad classification of mineral economics. Selected references have been given at the end of the report for the use of those interested in obtaining more detailed information on the subject. It is hoped that the present investigation will provide the basis for more detailed study on the recovery of selenium contained in New Mexico ores. ECONOMICS OF SELENIUM General Selenium was discovered in 1817 by John Jacob Berzelius while looking for a new source of the then rare element tellurium in the flue dust from the lead chambers of the sulfuric acid plant in Gripsholm, Sweden. So closely akin were these two elements that Berzelius decided to call the former selenium, from the Greek word Selene (moon), tellurium having been derived from the Latin word tellus (the earth). Although discovered in 1817, selenium remained but a laboratory curiosity for a little over half a century. Finally, in 1873, selenium was brought to public attention by the work of Willoughby Smith, who discovered the 3 particular characteristics of the electrical conductivity of selenium that helped in the development of the photoelectric cell. Thereafter, a multitude of appli- cations developed, so that this metal now plays a definite part in everyday life. Physical and Chemical Properties Selenium might be described as a paradoxical element, being either a metal or a nonmetal, a conductor or a nonconductor, a colorant or a decol- orant, and a hydrogenator or a dehydrogenator, as well as being either amor- phous or crystalline. The properties of selenium are understood more easily when its po- sition in the periodic table of the elements is examined. It stands in the sixth group (VIA), between sulfur and tellurium, both of which it resembles. Like sulfur, selenium occurs in a number of allotropic forms. However, the various forms of selenium are not so well defined as those of sulfur. Selenium boils at 684. 8°C, giving off dark-red vapors; at higher temperatures it sublimes, emitting yellowish vapors. Optically, metallic selenium is pleochroic and anisotropic, having an "0" index of 3. 0 and an "E" index of 4. 04. Electrically, selenium is a photoelectric semiconductor, a property that has contributed substantially to its great value in the modern electronic world. The chemical behavior of selenium is intermediate between that of sulfur and that of tellurium.
Recommended publications
  • Principles of Extractive Metallurgy Lectures Note
    PRINCIPLES OF EXTRACTIVE METALLURGY B.TECH, 3RD SEMESTER LECTURES NOTE BY SAGAR NAYAK DR. KALI CHARAN SABAT DEPARTMENT OF METALLURGICAL AND MATERIALS ENGINEERING PARALA MAHARAJA ENGINEERING COLLEGE, BERHAMPUR DISCLAIMER This document does not claim any originality and cannot be used as a substitute for prescribed textbooks. The information presented here is merely a collection by the author for their respective teaching assignments as an additional tool for the teaching-learning process. Various sources as mentioned at the reference of the document as well as freely available material from internet were consulted for preparing this document. The ownership of the information lies with the respective author or institutions. Further, this document is not intended to be used for commercial purpose and the faculty is not accountable for any issues, legal or otherwise, arising out of use of this document. The committee faculty members make no representations or warranties with respect to the accuracy or completeness of the contents of this document and specifically disclaim any implied warranties of merchantability or fitness for a particular purpose. BPUT SYLLABUS PRINCIPLES OF EXTRACTIVE METALLURGY (3-1-0) MODULE I (14 HOURS) Unit processes in Pyro metallurgy: Calcination and roasting, sintering, smelting, converting, reduction, smelting-reduction, Metallothermic and hydrogen reduction; distillation and other physical and chemical refining methods: Fire refining, Zone refining, Liquation and Cupellation. Small problems related to pyro metallurgy. MODULE II (14 HOURS) Unit processes in Hydrometallurgy: Leaching practice: In situ leaching, Dump and heap leaching, Percolation leaching, Agitation leaching, Purification of leach liquor, Kinetics of Leaching; Bio- leaching: Recovery of metals from Leach liquor by Solvent Extraction, Ion exchange , Precipitation and Cementation process.
    [Show full text]
  • Understanding Fluid–Rock Interactions and Lixiviant/Oxidant Behaviour for the In-Situ Recovery of Metals from Deep Ore Bodies
    School of Earth and Planetary Science Department of Applied Geology Understanding Fluid–Rock Interactions and Lixiviant/Oxidant Behaviour for the In-situ Recovery of Metals from Deep Ore Bodies Tania Marcela Hidalgo Rosero This thesis is presented for the degree of Doctor of Philosophy of Curtin University February 2020 1 Declaration __________________________________________________________________________ Declaration To the best of my knowledge and belief, I declare that this work of thesis contains no material published by any other person, except where due acknowledgements have been made. This thesis contains no material which has been accepted for the award of any other degree or diploma in any university. Tania Marcela Hidalgo Rosero Date: 28/01/2020 2 Abstract __________________________________________________________________________ Abstract In-situ recovery (ISR) processing has been recognised as a possible alternative to open- pit mining, especially for low-grade resources. In ISR, the fluid–rock interaction between the target ore and the lixiviant results in valuable- (and gangue-) metal dissolution. This interaction is achieved by the injection and recovery of fluid by means of strategically positioned wells. Although the application of ISR has become more common (ISR remains the preferential processing technique for uranium and has been applied in pilot programs for treating oxide zones in copper deposits), its application to hard-rock refractory and low-grade copper-sulfide deposits is still under development. This research is focused on the possible application of ISR to primary copper sulfides usually found as deep ores. Lixiviant/oxidant selection is an important aspect to consider during planning and operation in the ISR of copper-sulfide ores.
    [Show full text]
  • Treatment and Microscopy of Gold
    TREATMENT AND MICROSCOPY OF GOLD AND BASE METAL ORES. (Script with Sketches & Tables) Short Course by R. W. Lehne April 2006 www.isogyre.com Geneva University, Department of Mineralogy CONTENTS (Script) page 1. Gold ores and their metallurgical treatment 2 1.1 Gravity processes 2 1.2 Amalgamation 2 1.3 Flotation and subsequent processes 2 1.4 Leaching processes 3 1.5 Gold extraction processes 4 1.6 Cyanide leaching vs. thio-compound leaching 5 2. Microscopy of gold ores and treatment products 5 2.1 Tasks and problems of microscopical investigations 5 2.2 Microscopy of selected gold ores and products 6 (practical exercises) 3. Base metal ores and their beneficiation 7 3.1 Flotation 7 3.2 Development of the flotation process 7 3.3 Principles and mechanisms of flotation 7 3.4 Column flotation 9 3.5 Hydrometallurgy 10 4. Microscopy of base metal ores and milling products 10 4.1 Specific tasks of microscopical investigations 11 4.2 Microscopy of selected base metal ores and milling products 13 (practical exercises) 5. Selected bibliography 14 (Sketches & Tables) Different ways of gold concentration 15 Gravity concentration of gold (Agricola) 16 Gravity concentration of gold (“Long Tom”) 17 Shaking table 18 Humphreys spiral concentrator 19 Amalgamating mills (Mexican “arrastra”, Chilean “trapiche”) 20 Pressure oxidation flowsheet 21 Chemical reactions of gold leaching and cementation 22 Cyanide solubilities of selected minerals 23 Heap leaching flowsheet 24 Carbon in pulp process 25 Complexing of gold by thio-compounds 26 Relation gold content / amount of particles in polished section 27 www.isogyre.com Economically important copper minerals 28 Common zinc minerals 29 Selection of flotation reagents 30 Design and function of a flotation cell 31 Column cell flotation 32 Flowsheet of a simple flotation process 33 Flowsheet of a selective Pb-Zn flotation 34 Locking textures 35 2 1.
    [Show full text]
  • Identification and Description of Mineral Processing Sectors And
    V. SUMMARY OF FINDINGS As shown in Exhibit 5-1, EPA determined that 48 commodity sectors generated a total of 527 waste streams that could be classified as either extraction/beneficiation or mineral processing wastes. After careful review, EPA determined that 41 com modity sectors generated a total of 354 waste streams that could be designated as mineral processing wastes. Exhibit 5-2 presents the 354 mineral processing wastes by commodity sector. Of these 354 waste streams, EPA has sufficient information (based on either analytical test data or engineering judgment) to determine that 148 waste streams are potentially RCRA hazardous wastes because they may exhibit one or more of the RCRA hazardous characteristics: toxicity, ignitability, corro sivity, or reactivity. Exhibit 5-3 presents the 148 RCRA hazardous mineral processing wastes that will be subject to the Land Disposal Restrictions. Exhibit 5-4 identifies the mineral processing commodity sectors that generate RCRA hazardous mineral processing wastes that are likely to be subject to the Land D isposal Restrictions. Exhibit 5-4 also summarizes the total number of hazardous waste streams by sector and the estimated total volume of hazardous wastes generated annually. At this time, however, EPA has insufficient information to determine whether the following nine sectors also generate wastes that could be classified as mineral processing wastes: Bromine, Gemstones, Iodine, Lithium, Lithium Carbonate, Soda Ash, Sodium Sulfate, and Strontium.
    [Show full text]
  • Gold Extraction from Paleochannel Ores Using an Aerated Alkaline Glycine Lixiviant for Consideration in Heap and In-Situ Leaching Applications E.A
    Gold extraction from paleochannel ores using an aerated alkaline glycine lixiviant for consideration in heap and in-situ leaching applications E.A. Orabya,c, J.J. Eksteena*, A. Karrechb, M. Attarb aFaculty of Science and Engineering, Western Australian School of Mines: Minerals, Energy and Chemical Engineering, Curtin University, GPO Box U1987, Perth, WA 6845, Australia bDepartment of Civil, Environmental and Mining Engineering, The University of Western Australia, Australia c Mining and Metallurgical Engineering, Faculty of Engineering, Assiut University, Egypt *Corresponding Author: [email protected] ABSTRACT The decreasing grades of some gold deposits combined with the increasing depths, difficult surface topography, socioeconomic and geopolitical pressures often make the processing of such deposits infeasible by conventional mining, comminution and leaching technologies. To overcome these problems, the application of in-place, in-situ, and heap leaching often represent an optimal solution that minimises the capital and operating costs associated with mining and processing operations. Non- toxic, low cost lixiviants that are stable over an extended range of pH and Eh are required to provide any practical solution to ISL. Since ISL has the inherent benefit of increased natural rock temperature and pressure, glycine-based systems can be considered to extract valuable metals. Based on earlier studies on glycine leaching of pure gold foil, this research shows that Western Australian paleochannel ores are amenable to glycine-based ISL, at elevated alkalinity. The effects of pH, temperature, free glycine, ferric ions, sodium chloride and solids percentages on the kinetics of gold extraction were assessed. More than 85% of the gold can be extracted from ore with solutions containing 15 g/L glycine at pH 12.5 in 336 hours.
    [Show full text]
  • The Metallurgy of Antimony
    Chemie der Erde 72 (2012) S4, 3–8 Contents lists available at SciVerse ScienceDirect Chemie der Erde journal homepage: www.elsevier.de/chemer The metallurgy of antimony Corby G. Anderson ∗ Kroll Institute for Extractive Metallurgy, George S. Ansell Department of Metallurgical and Materials Engineering, Colorado School of Mines, Golden, CO 80401, United States article info abstract Article history: Globally, the primary production of antimony is now isolated to a few countries and is dominated by Received 4 October 2011 China. As such it is currently deemed a critical and strategic material for modern society. The metallurgical Accepted 10 April 2012 principles utilized in antimony production are wide ranging. This paper will outline the mineral pro- cessing, pyrometallurgical, hydrometallurgical and electrometallurgical concepts used in the industrial Keywords: primary production of antimony. As well an overview of the occurrence, reserves, end uses, production, Antimony and quality will be provided. Stibnite © 2012 Elsevier GmbH. All rights reserved. Tetrahedrite Pyrometallurgy Hydrometallurgy Electrometallurgy Mineral processing Extractive metallurgy Production 1. Background bullets and armory. The start of mass production of automobiles gave a further boost to antimony, as it is a major constituent of Antimony is a silvery, white, brittle, crystalline solid that lead-acid batteries. The major use for antimony is now as a trioxide exhibits poor conductivity of electricity and heat. It has an atomic for flame-retardants. number of 51, an atomic weight of 122 and a density of 6.697 kg/m3 ◦ ◦ at 26 C. Antimony metal, also known as ‘regulus’, melts at 630 C 2. Occurrence and mineralogy and boils at 1380 ◦C.
    [Show full text]
  • Extractive Metallurgy of Copper This Page Intentionally Left Blank Extractive Metallurgy of Copper
    Extractive Metallurgy of Copper This page intentionally left blank Extractive Metallurgy of Copper Mark E. Schlesinger Matthew J. King Kathryn C. Sole William G. Davenport AMSTERDAM l BOSTON l HEIDELBERG l LONDON NEW YORK l OXFORD l PARIS l SAN DIEGO SAN FRANCISCO l SINGAPORE l SYDNEY l TOKYO Elsevier The Boulevard, Langford Lane, Kidlington, Oxford OX5 1GB, UK Radarweg 29, PO Box 211, 1000 AE Amsterdam, The Netherlands First edition 1976 Second edition 1980 Third edition 1994 Fourth edition 2002 Fifth Edition 2011 Copyright Ó 2011 Elsevier Ltd. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise without the prior written permission of the publisher Permissions may be sought directly from Elsevier’s Science & Technology Rights Department in Oxford, UK: phone (+44) (0) 1865 843830; fax (+44) (0) 1865 853333; email: permissions@ elsevier.com. Alternatively you can submit your request online by visiting the Elsevier web site at http://elsevier.com/locate/permissions, and selecting Obtaining permission to use Elsevier material Notice No responsibility is assumed by the publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, products, instructions or ideas contained in the material herein British Library Cataloguing in Publication Data A catalogue record for this book is available from the British Library Library of Congress Cataloging-in-Publication Data A catalog record for this book is available from the Library of Congress ISBN: 978-0-08-096789-9 For information on all Elsevier publications visit our web site at elsevierdirect.com Printed and bound in Great Britain 11 12 13 14 10 9 8 7 6 5 Photo credits: Secondary cover photograph shows anode casting furnace at Palabora Mining Company, South Africa.
    [Show full text]
  • Technospheric Mining of Rare Earth Elements from Bauxite
    www.nature.com/scientificreports OPEN Technospheric Mining of Rare Earth Elements from Bauxite Residue (Red Mud): Process Optimization, Received: 3 May 2017 Accepted: 3 October 2017 Kinetic Investigation, and Published: xx xx xxxx Microwave Pretreatment Sable Reid1, Jason Tam2, Mingfan Yang1 & Gisele Azimi 1,2 Some rare earth elements (REEs) are classifed under critical materials, i.e., essential in use and subject to supply risk, due to their increasing demand, monopolistic supply, and environmentally unsustainable and expensive mining practices. To tackle the REE supply challenge, new initiatives have been started focusing on their extraction from alternative secondary resources. This study puts the emphasis on technospheric mining of REEs from bauxite residue (red mud) produced by the aluminum industry. Characterization results showed the bauxite residue sample contains about 0.03 wt% REEs. Systematic leaching experiments showed that concentrated HNO3 is the most efective lixiviant. However, because of the process complexities, H2SO4 was selected as the lixiviant. To further enhance the leaching efciency, a novel process based on microwave pretreatment was employed. Results indicated that microwave pretreatment creates cracks and pores in the particles, enabling the lixiviant to difuse further into the particles, bringing more REEs into solution, yielding of 64.2% and 78.7% for Sc and Nd, respectively, which are higher than the maximum obtained when HNO3 was used. This novel process of “H2SO4 leaching-coupled with-microwave pretreatment” proves to be a promising technique that can help realize the technological potential of REE recovery from secondary resources, particularly bauxite residue. Rare earth elements (REEs) have unique physicochemical properties that make them indispensable in many emerging critical and green innovations.
    [Show full text]
  • (12) United States Patent (10) Patent No.: US 8,097,227 B2 Hacklet Al
    USO0809.7227B2 (12) United States Patent (10) Patent No.: US 8,097,227 B2 Hacklet al. (45) Date of Patent: Jan. 17, 2012 (54) METHOD FOR THOSULFATE LEACHING 4,721,526 A 1/1988 Elmore et al. OF PRECIOUS METAL-CONTAINING 4,723,998 A 2, 1988 O’Neil 4,738,718 A 4, 1988 Bakshani et al. MATERLALS 4,740,243 A 4, 1988 Krebs-Yuillet al. 4,765,827 A 8/1988 Clough et al. (75) Inventors: Ralph Peter Hackl, Vancouver (CA); 4,778,519 A 10, 1988 Pesic Jinxing Ji, Burnaby (CA); Paul George 4,801,329 A 1/1989 Clough et al. 4,816,234 A 3, 1989 Brison et al. West-Sells, Vancouver (CA) 4,816,235 A 3, 1989 Pesic 4.902,345 A 2f1990 Ball et al. (73) Assignee: Placer Dome Technical Services 4,913,730 A 4, 1990 Deschenes et al. Limited, Vancouver (CA) 4,923,510 A 5/1990 Ramadorai et al. 4,925.485 A 5, 1990 Schulze (*) Notice: Subject to any disclaimer, the term of this 4,980,134 A 12, 1990 Butler 5,051,128 A 9, 1991 Kubo patent is extended or adjusted under 35 5,071.477 A 12/1991 Thomas et al. U.S.C. 154(b) by 0 days. 5,114,687 A 5/1992 Han et al. 5,127.942 A 7/1992 Brierley et al. (21) Appl. No.: 12/683,967 5,147,617 A 9, 1992 Touro et al. 5,147,618 A 9, 1992 Touro et al. (22) Filed: Jan.
    [Show full text]
  • Manual of Acid in Situ Leach Uranium Mining Technology
    IAEA-TECDOC-1239 Manual of acid in situ leach uranium mining technology August 2001 The originating Section of this publication in the IAEA was: Nuclear Fuel Cycle and Materials Section International Atomic Energy Agency Wagramer Strasse 5 P.O. Box 100 A-1400 Vienna, Austria MANUAL OF ACID IN SITU LEACH URANIUM MINING TECHNOLOGY IAEA, VIENNA, 2001 IAEA-TECDOC-1239 ISSN 1011–4289 © IAEA, 2001 Printed by the IAEA in Austria August 2001 FOREWORD An important part of the IAEA programme for reactor fuels involves eliciting and circulating information on innovative uranium production technologies. As compared with conventional mining, in situ leach (ISL) technology is both innovative and relatively young. It is recognized as having economic and environmental advantages when properly employed by knowledgeable specialists to extract uranium from suitable sandstone type deposits. In recent years ISL uranium mining has been producing about 13 to 15 per cent of world output. Because of its potential for both low cost recovery and having environmental advantages, the use of the technology will very probably increase. This may occur because sandstone hosted uranium deposits amenable to ISL recovery are relatively widespread in the world. ISL technology recovers uranium using two alternative chemical leaching systems — acid and alkaline. Acid leach is the more widely employed and has historically produced a majority of the world’s ISL production. This technology, with its origins in the 1960s, was developed and employed in the former Soviet Union and the successor states, as well as in central and eastern Europe. The report describes operational practices developed under the economic systems, together with the governmental policies and programmes prevailing over this period.
    [Show full text]
  • In Situ Resource Recovery from Waste Repositories: Exploring the Potential for Mobilization and Capture of Metals from Anthropogenic Ores
    J. Sustain. Metall. DOI 10.1007/s40831-016-0102-4 RESEARCH ARTICLE In Situ Resource Recovery from Waste Repositories: Exploring the Potential for Mobilization and Capture of Metals from Anthropogenic Ores 1 1 1 Devin Sapsford • Peter Cleall • Michael Harbottle Ó The Author(s) 2016. This article is published with open access at Springerlink.com Abstract Wastes and the waste repositories in which they Introduction reside are becoming targets for resource recovery, both for legacy wastes and for future waste arisings as part of a Waste repositories can be considered the ore deposits of the desire to move toward a circular economy. There is an ‘anthropocene.’ Having historically disposed of vast urgent requirement to explore concepts for practicable quantities of industrial, municipal, metallurgical, and technologies that can be applied to these ends. This paper mining waste into or onto the ground, societies have put presents a synthesis of concepts concerning in situ tech- into geological storage an enormous quantity of resource in nologies (developed from mining and contaminated land a range of materials of value such as metals and energy (in remediation industries) that have enormous potential for the form of biomass and polymers). Therefore, instead of application to technospheric mining. Furthermore, poten- considering these waste repositories to be a legacy waste tial target waste streams and their mineralogy and character issue and a long-term liability, a paradigm shift is required are presented along with a discussion concerning lixiviant to view these installations as ‘resource hubs’ for future and metal capture systems that could be applied. Issues of recovery.
    [Show full text]
  • Simulation and Modelling of Zinc Recovery Process from Steel Scrap
    SIMULATION AND MODELLING OF ZINC RECOVERY PROCESS FROM STEEL SCRAP A Thesis Submitted to the College of Graduate and Postdoctoral Studies In Partial Fulfillment of the Requirement For the Degree of Master of Science In the Department of Chemical and Biological Engineering University of Saskatchewan Saskatoon, SK, Canada By OLATUNJI OLABIYI © Copyright Olatunji Olabiyi, October 2020. All Rights Reserved. Unless otherwise noted, copyright of the material in this thesis belongs to the author i PERMISSION TO USE In presenting this thesis in partial fulfillment of the requirements for a Postgraduate degree from the University of Saskatchewan, I agree that the Libraries of this University may make it freely available for inspection. I further agree that the permission for copying of this thesis in any manner, in whole or in part, for scholarly purposes may be granted by Dr. Shafiq Alam who supervised my thesis work, or in his absence, by the Head of the Department or the Dean of the College in which my thesis work was done. It is understood that any copying or publication or use of this thesis or parts thereof for financial gain shall not be allowed without my written permission. It is also understood that due recognition shall be given to me and to the University of Saskatchewan in any scholarly use which may be made of any material in my thesis Request for permission to copy or make other use of material in this thesis in whole or part should be addressed to: Head of the Department of Chemical and Biological Engineering University of Saskatchewan 57 Campus Drive Saskatoon, Saskatchewan Canada, S7N 5A9 Or Dean College of Graduate and Postdoctoral Studies University of Saskatchewan Room 116, 110 Science Place Thorvaldson Building, Saskatoon, Saskatchewan Canada, S7N 5C9 i ABSTRACT This research project addressed a practical problem besetting electric arc furnace (EAF) steelmakers and environmentalists for many years.
    [Show full text]