Broderie Anglaise Lace' Shoettes

Total Page：16

File Type：pdf, Size：1020Kb

Instructions for 'Broderie Anglaise Lace' Shoettes You Will Need: Water Soluble Vilene Pre-Shrunk Fabric – either a good quality Linen fabric or Poly – Cotton Embroidery Thread 2 x Length of ribbon no wider than ¼ inch / 5mm & 10 inches / 25 cm in length Wing Needle Quick Unpick Regular Sewing Machine 'Bodkin' – to help thread the ribbon through the eyelet holes Magic Tape You will need to Stitch out per Pair Of Shoettes: 2 x Front 2 x Back 2 x Left Side 2 x Right Side 2 x Sole Please check with your Dealer which is the best 'Wing Needle' to use for your machine. When using a Wing Needle, please use an embroidery foot with a biggish hole – please check with your Dealer which foot they would recommend. All the Design Pieces are stitched out using the method below: Hoop a Double Layer of Water Soluble Vilene. Please ensure that the water soluble vilene is flat and smooth when it is hoop and is 'firm' in the hoop. There must be no folds or bubbles as this will affect the stitch out. Stitch out the First Colour – this is an outline of the design piece. Place a piece of fabric on top of this running stitch outline. Stitch out the second colour – this is again an outline of the design piece and will hold the fabric in place. Remove the hoop from the machine. Replace your 'regular' embroidery needle with the wing needle. Replace the hoop in the machine and stitch out the third colour. This will be the broderie anglaise patterning. Remove the hoop from the machine. Remove the wing needle and replace with your regular embroidery needle. Using a sharp nosed pair of scissors, carefully cut the surrounding fabric from around the design piece. Replace the hoop in the machine and stitch out the next colour. This will be the edging around the design piece. Stitch out the rest of the design. Stitching out the Soles: Hoop a double layer of water soluble vilene. Stitch out the first colour – this is an outline of the sole. Place a double layer of fabric on to of the outline. Stitch out the second colour – this is again an outline of the sole. Using a sharp nosed pair of scissors, trim away the excess fabric from around the sole. Stitch out the final colour – this is a satin stitch edging. Assembly: You will need your regular sewing machine to assemble the shoettes. I used a zig zag stitch. Density approximately .5 and a width of 3 mm Tape the sides to the sole and stitch into place: Next, pin the Front to the sole and gently 'ease' while stitching into place: Pin the Back to the Sole and stitch into place. Gently and carefully use the 'quick unpick' to open the eyelet holes. Rinse out the shoettes. Allow to dry. Using the Bodkin thread the ribbon through the eyelet holes to complete. Enjoy! Kind regards Phil [email protected] www.bargainembstore.com.

Copy Link

Recommended publications

Palmetto Tatters Guild Glossary of Tatting Terms (Not All Inclusive!)
Palmetto Tatters Guild Glossary of Tatting Terms (not all inclusive!) Tat Days Written * or or To denote repeating lines of a pattern. Example: Rep directions or # or § from * 7 times & ( ) Eg. R: 5 + 5 – 5 – 5 (last P of prev R). Modern B Bead (Also see other bead notation below) notation BTS Bare Thread Space B or +B Put bead on picot before joining BBB B or BBB|B Three beads on knotting thread, and one bead on core thread Ch Chain ^ Construction picot or very small picot CTM Continuous Thread Method D Dimple: i.e. 1st Half Double Stitch X4, 2nd Half Double Stitch X4 dds or { } daisy double stitch DNRW DO NOT Reverse Work DS Double Stitch DP Down Picot: 2 of 1st HS, P, 2 of 2nd HS DPB Down Picot with a Bead: 2 of 1st HS, B, 2 of 2nd HS HMSR Half Moon Split Ring: Fold the second half of the Split Ring inward before closing so that the second side and first side arch in the same direction HR Half Ring: A ring which is only partially closed, so it looks like half of a ring 1st HS First Half of Double Stitch 2nd HS Second Half of Double Stitch JK Josephine Knot (Ring made of only the 1st Half of Double Stitch OR only the 2nd Half of Double Stitch) LJ or Sh+ or SLJ Lock Join or Shuttle join or Shuttle Lock Join LPPCh Last Picot of Previous Chain LPPR Last Picot of Previous Ring LS Lock Stitch: First Half of DS is NOT flipped, Second Half is flipped, as usual LCh Make a series of Lock Stitches to form a Lock Chain MP or FP Mock Picot or False Picot MR Maltese Ring Pearl Ch Chain made with pearl tatting technique (picots on both sides of the chain, made using three threads) P or - Picot Page 1 of 4 PLJ or ‘PULLED LOOP’ join or ‘PULLED LOCK’ join since it is actually a lock join made after placing thread under a finished ring and pulling this thread through a picot.
[Show full text]
NEEDLE LACES Battenberg, Point & Reticella Including Princess Lace 3Rd Edition
NEEDLE LACES BATTENBERG, POINT & RETICELLA INCLUDING PRINCESS LACE 3RD EDITION EDITED BY JULES & KAETHE KLIOT LACIS PUBLICATIONS BERKELEY, CA 94703 PREFACE The great and increasing interest felt throughout the country in the subject of LACE MAKING has led to the preparation of the present work. The Editor has drawn freely from all sources of information, and has availed himself of the suggestions of the best lace-makers. The object of this little volume is to afford plain, practical directions by means of which any lady may become possessed of beautiful specimens of Modern Lace Work by a very slight expenditure of time and patience. The moderate cost of materials and the beauty and value of the articles produced are destined to confer on lace making a lasting popularity. from “MANUAL FOR LACE MAKING” 1878 NEEDLE LACES BATTENBERG, POINT & RETICELLA INLUDING PRINCESS LACE True Battenberg lace can be distinguished from the later laces CONTENTS by the buttonholed bars, also called Raleigh bars. The other contemporary forms of tape lace use the Sorrento or twisted thread bar as the connecting element. Renaissance Lace is INTRODUCTION 3 the most common name used to refer to tape lace using these BATTENBERG AND POINT LACE 6 simpler stitches. Stitches 7 Designs 38 The earliest product of machine made lace was tulle or the PRINCESS LACE 44 RETICELLA LACE 46 net which was incorporated in both the appliqued hand BATTENBERG LACE PATTERNS 54 made laces and later the elaborate Leavers laces. It would not be long before the narrow tapes, in fancier versions, would be combined with this tulle to create a popular form INTRODUCTION of tape lace, Princess Lace, which became and remains the present incarnation of Belgian Lace, combining machine This book is a republication of portions of several manuals made tapes and motifs, hand applied to machine made tulle printed between 1878 and 1938 dealing with varieties of and embellished with net embroidery.
[Show full text]
Bobbin Lace You Need a Pattern Known As a Pricking
“Dressing” a Lace Pillow © Jean Leader 2014 pricking pin-cushion this edge should be a selvage if possible — the other edges lace in progress should be hemmed. cover cloth between bobbins and lower part of pricking cover cloth ready to cover pillow when not in use The pillow, a square or round piece of polystyrene (preferably high density) about 40 cm (16 in) across and 5 cm (2 in) thick, should be covered with a firmly woven dark cotton material. Avoid synthetic materials as these will attract dust and fluff. Cut a piece of material so that it is about 8-10 cm (3-4 in) wider than the pillow all round. Make a hem (with an opening) round the edge and thread either tape or elastic through it. Fit the cover over the pillow and pull the tape or elastic tight. (If you’re in a hurry just pin the cover in place.) This cover should be removed and washed occasionally. You will also need at least two cover cloths about 40 cm (16 in) square made of the same sort of material as the cover (they should be hemmed so no bits of thread can catch in the lace). One of these is placed over the lower part of the pricking and the bobbins lie on top of it. The other cloth is placed over the whole pillow when it is not in use so that the lace you’re working on stays clean. Making a Pricking In order to make bobbin lace you need a pattern known as a pricking.
[Show full text]
Powerhouse Museum Lace Collection: Glossary of Terms Used in the Documentation – Blue Files and Collection Notebooks
Book Appendix Glossary 12-02 Powerhouse Museum Lace Collection: Glossary of terms used in the documentation – Blue files and collection notebooks. Rosemary Shepherd: 1983 to 2003 The following references were used in the documentation. For needle laces: Therese de Dillmont, The Complete Encyclopaedia of Needlework, Running Press reprint, Philadelphia, 1971 For bobbin laces: Bridget M Cook and Geraldine Stott, The Book of Bobbin Lace Stitches, A H & A W Reed, Sydney, 1980 The principal historical reference: Santina Levey, Lace a History, Victoria and Albert Museum and W H Maney, Leeds, 1983 In compiling the glossary reference was also made to Alexandra Stillwell’s Illustrated dictionary of lacemaking, Cassell, London 1996 General lace and lacemaking terms A border, flounce or edging is a length of lace with one shaped edge (headside) and one straight edge (footside). The headside shaping may be as insignificant as a straight or undulating line of picots, or as pronounced as deep ‘van Dyke’ scallops. ‘Border’ is used for laces to 100mm and ‘flounce’ for laces wider than 100 mm and these are the terms used in the documentation of the Powerhouse collection. The term ‘lace edging’ is often used elsewhere instead of border, for very narrow laces. An insertion is usually a length of lace with two straight edges (footsides) which are stitched directly onto the mounting fabric, the fabric then being cut away behind the lace. Ocasionally lace insertions are shaped (for example, square or triangular motifs for use on household linen) in which case they are entirely enclosed by a footside. See also ‘panel’ and ‘engrelure’ A lace panel is usually has finished edges, enclosing a specially designed motif.
[Show full text]
Identifying Handmade and Machine Lace Identification
Identifying Handmade and Machine Lace DATS in partnership with the V&A DATS DRESS AND TEXTILE SPECIALISTS 1 Identifying Handmade and Machine Lace Text copyright © Jeremy Farrell, 2007 Image copyrights as specified in each section. This information pack has been produced to accompany a one-day workshop of the same name held at The Museum of Costume and Textiles, Nottingham on 21st February 2008. The workshop is one of three produced in collaboration between DATS and the V&A, funded by the Renaissance Subject Specialist Network Implementation Grant Programme, administered by the MLA. The purpose of the workshops is to enable participants to improve the documentation and interpretation of collections and make them accessible to the widest audiences. Participants will have the chance to study objects at first hand to help increase their confidence in identifying textile materials and techniques. This information pack is intended as a means of sharing the knowledge communicated in the workshops with colleagues and the public. Other workshops / information packs in the series: Identifying Textile Types and Weaves 1750 -1950 Identifying Printed Textiles in Dress 1740-1890 Front cover image: Detail of a triangular shawl of white cotton Pusher lace made by William Vickers of Nottingham, 1870. The Pusher machine cannot put in the outline which has to be put in by hand or by embroidering machine. The outline here was put in by hand by a woman in Youlgreave, Derbyshire. (NCM 1912-13 © Nottingham City Museums) 2 Identifying Handmade and Machine Lace Contents Page 1. List of illustrations 1 2. Introduction 3 3. The main types of hand and machine lace 5 4.
[Show full text]
Project Gutenberg's Beeton's Book of Needlework, by Isabella Beeton
Project Gutenberg's Beeton's Book of Needlework, by Isabella Beeton This eBook is for the use of anyone anywhere at no cost and with almost no restrictions whatsoever. You may copy it, give it away or re-use it under the terms of the Project Gutenberg License included with this eBook or online at www.gutenberg.net Title: Beeton's Book of Needlework Author: Isabella Beeton Release Date: February 22, 2005 [EBook #15147] Language: English Character set encoding: ISO-8859-1 *** START OF THIS PROJECT GUTENBERG EBOOK BEETON'S BOOK OF NEEDLEWORK *** Produced by Julie Barkley and the PG Online Distributed Proofreading Team. BEETON'S BOOK OF NEEDLEWORK. CONSISTING OF DESCRIPTIONS AND INSTRUCTIONS, ILLUSTRATED BY SIX HUNDRED ENGRAVINGS, OF TATTING PATTERNS. CROCHET PATTERNS. KNITTING PATTERNS. NETTING PATTERNS. EMBROIDERY PATTERNS. POINT LACE PATTERNS. GUIPURE D'ART. BERLIN WORK. MONOGRAMS. INITIALS AND NAMES. PILLOW LACE, AND LACE STITCHES. Every Pattern and Stitch Described and Engraved with the utmost Accuracy and the Exact Quantity of Material requisite for each Pattern stated. CHANCELLOR PRESS Beeton's Book of Needlework was originally published in Great Britain in 1870 by Ward, Lock and Tyler. This facsimile edition published in Great Britain in 1986 by Chancellor Press 59 Grosvenor Street London W 1 Printed in Czechoslovakia 50617 SAMUEL BUTLER'S PREFACE The Art of Needlework dates from the earliest record of the world's history, and has, also, from time immemorial been the support, comfort, or employment of women of every rank and age. Day by day, it increases its votaries, who enlarge and develop its various branches, so that any addition and assistance in teaching or learning Needlework will be welcomed by the Daughters of England, "wise of heart," who work diligently with their hands.
[Show full text]
All About Macramé History of Macramé
August 2019 Newsletter All about Macramé For August we thought we would ring the changes and dedicate this edition of the newsletter to a fibre art that was popular in the 1970’s and 80’s for making wall hangings and potholders but which has recently made a resurgence in fibre art. Some customers have also found that the weaversbazaar cotton and linen warps are ideally suited to macramé. So we have all been having a go. Dianne Miles, one of the weaversbazaar tutors, has extensive experience in Macramé and has designed a one day course to show how the techniques can be incorporated into Tapestry for stunning effect – more details below. So we would like to show you some of the best work going on and introduce you to some of the cross overs with other textile art. History of Macramé The earliest recorded macramé knots appear in decorative carvings of the Babylonians and Assyrians. Macramé was introduced to Europe via Spain during its conquest by the Moors and the word is believed to derive from a 13th century Arabic weavers term meaning fringe as the knots were used to turn excess yarn into decorative edges to finish hand woven fabrics. Probably introduced to England by Queen Mary in the late 17th century it was also practiced by sailors who made decorative objects (such as hammocks, belts etc.) whilst at sea thereby disseminating it even further afield when they sold their work in port. It was also known as McNamara’s Lace. The Victorians loved macramé for “rich trimming” for clothing and household items with a favourite book being “Sylvia’s Book of Macramé Lace” which is still available today.
[Show full text]
African Lace
Introduction Does changing an original material destroy its traditional context? If a material assumes new meaning or significance in a new context, is this inherently an appropriation of the object? What loss does this cause, and is it a positive change, a negative one, or neither? This lexicon revolves around African Lace. Through an analysis of this particular material, I broadly explain, craftsmanship, authenticity and reasons behind an object’s creation, including why and how it is made, from which materials, and how the object translates into a specific environment. Various kinds of objects are created in and relate to specific places and time periods. If situated in an environment in which it did not originate, the meaning of an object changes. In fact, the object is used from a new perspective. Although it is possible to reuse an object as a source of inspiration or research, it cannot be used as it was in its previous context. Thus, it is necessary to rethink the authenticity of an object when it is removed from its past context. History is important and can explain a materials origin, and it therefore warrants further attention. A lack of knowledge results in a loss of authenticity and originality of a historical material. In view of this, I develop this Lexicon to elaborate on the importance of this historical attention. It is interesting to consider how an object can influence a user in relation to emotional or even material value. The extent of this influence is uncertain, but it is a crucial aspect since any situation could diminish the value and the meaning of an object.
[Show full text]
Sheila Machines in Switzerland Are Busy As I Write, Re- Running Some Old Favorites
Bear in Mind An electronic newsletter from Bear Threads Ltd. Volume 10 – Issue 6 June/July 2018 From The Editor – however, is that we will be introducing some gorgeous NEW embroideries in our next issue – “A rainy day in Georgia” indeed as Alberto dumps August. These are beautiful designs and very more rain on our soggy ground. But a great much in line with our two-part feature on Broidere stitching week as well, as we are officially into Anglaise. summer, albeit not by the calendar!!! I gathered supplies for my summer stitching projects before And put the date of Sunday, September 9, 2018 on the Memorial Day weekend, my porches are clean your calendar NOW to make sure you can see us and everything ready for summer sipping and at the Birmingham Creative Sewing Market. I stitching. assure you, it would be tragic not to be one of the first to see the new Swiss Broderie Anglaise Remember that we publish ‘Bear In Mind’ 10 times embroideries, as well as our newest lace set. And a year, combining June and July as well as for icing on the cake we will have certain Maline November and December. So this issue is really laces available for ½ price – guess that your eyes not late, but rather we are stretching the lazy days and ears perked up!!! of summer. We have definitely not been lazy here at the office, as the website now has been updated So for now, enjoy your summer, be saving your with the newsletter index, our newest lace set, and money for September, and all the past newsletters.
[Show full text]
ABOUT LACE by Anna Haraldsson Cutwork Needle Embroidery
ALL ABOUT LACE by Anna Haraldsson Cutwork Needle Embroidery ( ) Cut inside marked area if not using INSPIRA™ Cutwork Embroider cutwork with Embroider cutwork using Needles INSPIRA™ Cutwork traditional scissor for cut Needles outs in design. 1. 1. Add a new heavy weight water soluble stabilizer underneath the hoop for cutwork embroidery, or add fabric underneath Eylet 4 mm * the hoop for reversed applique. Eylet 4 mm 2. 2. Trim and remove the cut fabric if using INSPIRA™ Cutwork Cut inside marked area Cut inside marked area ( ) if not using INSPIRA™ Needles ( ) if not using INSPIRA™ Cutwork Needles Cutwork Needles 3. 3. Needle #1 Needle #1 Clean the Bobbin Area 4. 4. Needle #2 Needle #2 Add a heavy weight This design cannot be rotated or mirrored Add a heavy weight water soluble stabilizer water soluble stabilizer * underneath the hoop * underneath the hoop 5. 5. INSPIRA™ Cutwork Needle #1 Trim and remove the Trim and remove the cut fabric INSPIRA™ Cutwork Needle #2 cut fabric 6. 6. INSPIRA™ Cutwork Needle #3 Clean the Bobbin Area Clean the Bobbin Area INSPIRA™ Cutwork Needle #4 IMPORTANT RESIZING NOTICE: Embroideries digitized for Cutwork Needles CAN NOT be resized or scaled. Appliqué *✶ Heavyweight water Freestanding Cut Edge soluble stabilizer Embroideries creative™ GRAND ENDLESS HOOP Endless embroideries Design #18-27 All designs in this collection are shown in 50% of real size. All designs are stitched with Robison-Anton 40 wt decorative thread. Gütermann Sulky thread numbers are given below the Robison-Anton numbers. www.pfaff.com, www.myembroideries.com Design #2, 7, 11, 15, 17 The design begins with 4 position stitches for easy matching when creating All Over-embroidered fabric.
[Show full text]
Techniques Represented in Each Pattern
(updated) November 12, 2020 Dear Customer: Thank you for requesting information about my lace instruction and supply business. If you have any questions about the supplies listed on the following pages, let me use my 36 years of lacemaking experience to help you in your selections. My stock is expanding and changing daily, so if you don't see something you want please ask. It would be my pleasure to send promotional materials on any of the items you have questions about. Call us at (607) 277-0498 or visit our web page at: http://www.vansciverbobbinlace.com We would be delighted to hear from you at our email address [email protected]. All our orders go two day priority service. Feel free to telephone, email ([email protected]) or mail in your order. Orders for supplies will be ﬁlled immediately and will include a free catalogue update. Please include an 8% ($7.50 minimum to 1 lb., $10.50 over 1 lbs.-$12.00 maximum except for pillows and stands which are shipped at cost) of the total order to cover postage and packaging. New York State residents add sales tax applicable to your locality. Payment is by check, money order or credit card (VISA, MASTERCARD, DISCOVER) in US dollars. If you are looking for a teacher keep me in mind! I teach courses at all levels in Torchon, Bedfordshire, Lester, Honiton, Bucks Point lace, Russian and more! I am happy to tailor workshops to suit your needs. Check for scheduled workshops on the page facing the order form.
[Show full text]
Madeira Embroidery
Blackwork Journey Inspirations Madeira Embroidery Madeira is an island located in the Atlantic Ocean west and slightly south of Portugal. The capital of Madeira is Funchai on the main island’s south coast and it was to Funchai, the capital that I travelled to explore the history of Madeira embroidery and find some modern examples of this traditional form of whitework embroidery. The hand embroidery of Madeira is generally recognised as being the finest of its kind available in the world. Over the last 150 years, Madeira has collected expertise from the fast disappearing regional centres of hand embroidery across Europe and moulded these various styles into a distinctive form of handwork recognised throughout the world. The Development of Madeira Embroidery The story began in the 1860’s when a wine shipper’s daughter, Elizabeth Phelps turned the rural pastime of simple embroidery into a cottage industry using her skills to motivate, organise and sell the work of the embroiders to Victorian England. In the 1860’s it was estimated that there were 70,000 women embroiderers (bordadeiras) in Madeira working on linen, silk, organdy and cotton to create table linen, clothing, bedding and handkerchiefs. Today there are about 30 companies producing handmade embroideries employing around 4,500 embroiderers. During the 19th century the main exports were to England and Germany. In the 20th century Madeiran Embroidery was exported to many parts of the world. Italy, the United States, South America and Australia became important markets. France, Singapore, Holland, Brazil and other countries also contributed to the trading expansion of and reputation of Madeira Embroidery.
[Show full text]