DOCSLIB.ORG

Ts-480Hx Ts-480Sat

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Ts-480Hx Ts-480Sat INSTRUCTION MANUAL HF/50MHz ALL MODE TRANSCEIVER TS-480 CL XIT PF ANT 1/2 RIT ATT/PRE AT 1 REC 2 REC 3 REC M.IN CH1 CH2 CH3 DNL QMI TF-SET NAR MODE AF SQL 46TX MONI 5 RF.G DELAY M VFO IF F.LOCK MULTI SHIFT PWR MIC KEY NR FIL QMR 7 8 9 MENU M/V NB/T VOX PROC BC CW.T A / B SPLIT CLR 0 OFF STEP SG.SEL MHz A=B MTR AGC ENT FINE SCAN HF/ 50 MHz ALL MODE TRANSCEIVER TS-480HX TS-480SAT NOTIFICATION This equipment complies with the essential requirements of Directive 2014/53/EU. This equipment requires a licence and is intended for use in the countries below. AT BE DK FI FR DE GR IS IE IT LI LU NL NO PT ES SE CH GB CY CZ EE HU LV LT MT PL SK SI BG RO HR TR ISO3166 B62-1735-50 (K, E) NOTICE TO THE USER BEFORE STARTING One or more of the following statements may be Amateur radio regulations vary from country to applicable for this equipment. country. Confirm your local amateur radio regulations and requirements before operating the transceiver. FCC WARNING Depending on the size and type of vehicle, the This equipment generates or uses radio frequency energy. maximum transmission output power for the mobile Changes or modifications to this equipment may cause harmful operation will vary. The maximum transmission interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to output power is usually specified by the car operate this equipment if an unauthorized change or manufacturer to avoid interference with other electric modification is made. devices used in the vehicle. Consult your car manufacturer and amateur radio equipment dealer for the requirements and installation. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Information on Disposal of Old Electrical and • Consult the dealer for technical assistance. Electronic Equipment and Batteries (applicable for countries that have adopted separate waste collection systems) Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment. THANK YOU THANK YOU SUPPLIED ACCESSORIES Thank you for choosing this KENWOOD TS-480HX/ After carefully unpacking the transceiver, identify the SAT transceiver. It has been developed by a team of items listed in the table below. We recommend you engineers determined to continue the tradition of keep the box and packing materials in case you need excellence and innovation in KENWOOD to repack the transceiver in the future. transceivers. Quantity This transceiver features a Digital Signal Processing (DSP) unit to process AF signals. By taking Accessory Part Number TS-480SAT TS-480HX maximum advantage of DSP technology, the TS-480HX/ SAT transceiver gives you enhanced K E K E interference reduction capabilities and improves the quality of audio. You will notice the differences when MXicrophone T91-0638-X 1111 you fight QRM and QRN. As you learn how to use DXC power cable E30-3489-X 1122 this transceiver, you will also find that KENWOOD is mini DIN plug E57-0404-XX 1111 pursuing “user friendliness”. For example, each time (6-pin male) you change the Menu No. in Menu mode, you will see mini DIN plug scrolling messages on the display that tell you what E57-0405-XX 1111 (8-pin male) you are selecting. Modular cable E30-3488-XX 1111 Though user friendly, this transceiver is technically (RJ-11 4 m) sophisticated and some features may be new to you. Modular cable Consider this manual to be a personal tutorial from E30-3500-XX –1–1 (RJ-11 20 cm) the designers. Allow the manual to guide you through the learning process now, then act as a reference in FXuse (25 A) F05-2531-X 1122 the coming years. FXuse (4 A) F06-4027-X 1111 Screw Set for N99-2035-XX 1111 brackets (A) FEATURES LX-bracket J29-0706-X 2222 • All mode operation from HF to 50 MHz amateur PXanel holder J29-0663-X 1212 radio band Panel bracket J29-0707-XX 1111 • Separate Remote Control panel for mobile (mobile) operation Panel bracket J09-0409-XX 1111 • Digital Signal Processing (DSP) unit (base) Line filter with a • Adjustable DSP filter frequencies L79-1408-XX –1–2 retaining band • A built-in Antenna Tuner for the HF/ 50 MHz band Line filter for (TS-480SAT) L79-1417-XX 1111 Panel • 200 watts✽1 output power (SSB, CW, FSK, FM) PXortable bracket J29-0705-X –1–1 and 50 watts✽2 output power (AM) for the TS-480HX. CXarrying handle K01-0420-X –1–1 ✽1 50 MHz band: 100 watts Screw set for ✽2 50 MHz band: 25 watts Portable bracket N99-2041-XX –1–1 (B) • 100 watts output power (SSB, CW, FSK, FM) and 25 watts output power (AM) for the TS-480SAT. B62-1735-XX E1111 B62-1750-XX –1–1F Instruction B62-1752-XX –1–1S Manual B62-1736-XX –1–1G B62-1751-XX –1–1I B62-1753-XX –1–1D Schematic/ B52-0619-XX 1–1– Block Diagrams B52-0620-XX Warranty card – 1111 i THANK YOU MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual. TS-480HX : HF/ 50 MHz All mode Transceiver (200 watts✽1 output power: SSB, CW, FSK, FM/ 50 watts✽2 output power: AM) ✽1 50 MHz band: 100 watts ✽2 50 MHz band: 25 watts TS-480SAT : HF/ 50 MHz All mode Transceiver with Automatic Antenna Tuner (100 watts output power: SSB, CW, FSK, FM/ 25 watts output power: AM) MARKET CODES K-type : The Americas E-type : Europe/ General The market code is shown on the carton box. Refer to the specifications {page 91} for information on the available operating frequencies. WRITING CONVENTIONS FOLLOWED The writing conventions described below have been followed to simplify instructions and avoid unnecessary repetition. Instruction What to Do Press [KEY].ePress and releas KEY. Press Press KEY1 momentarily, release [KEY1], [KEY2]. KEY1, then press KEY2. Press Press and hold KEY down for a [)KEY] (1 s . second and then release KEY. Press and hold KEY1 down, then press KEY2. If there are more Press than two keys, press and hold [KEY1]+[KEY2]. down each key in turn until the final key has been pressed. With the transceiver OFF, press Press and hold KEY, then switch ON [KEY]+[ ]. the transceiver power by pressing [] (POWER). ii PRECAUTIONS Please observe the following precautions to prevent • Locate the transceiver away from heat sources fire, personal injury, and transceiver damage: such as a radiator, stove, amplifier or other • Connect the transceiver only to a power source devices that produce substantial amounts of heat. described in this manual or as marked on the • Do not use volatile solvents such as alcohol, paint transceiver itself. thinner, gasoline or benzene to clean the cabinet • Route all power cables safely. Ensure the power of the transceiver. Use a clean cloth with warm cables can neither be stepped upon nor pinched water or a mild detergent. by items placed near or against the cables. Pay • Disconnect the input power cable from the power particular attention to locations near AC source when the transceiver is not used for long receptacles, AC outlet strips, and points of entry to periods of time. the transceiver. • Remove the transceiver’s enclosure only to do • Take care not to drop objects or spill liquid into the accessory installations described in this manual or transceiver through enclosure openings. Metal accessory manuals. Follow provided instructions objects, such as hairpins or needles, inserted into carefully, to avoid electrical shocks. If unfamiliar the transceiver may contact voltages resulting in with this type of work, seek assistance from an serious electrical shocks. Never permit children to experienced individual, or have a professional insert any objects into the transceiver. technician do the task. • Do not attempt to defeat methods used for • Enlist the services of qualified personnel in the grounding and electrical polarization in the following cases: transceiver, particularly involving the power input a) The power supply or plug is damaged. cable. b) Objects have fallen or liquid has spilled into the • Adequately ground all outdoor antennas for this transceiver. transceiver using approved methods. Grounding helps protect against voltage surges caused by c) The transceiver has been exposed to rain.
Load more

Recommended publications
  • Telecommunication Switching Networks
    TELECOMMUNICATION SWITCHING AND NETWORKS TElECOMMUNICATION SWITCHING AND NffiWRKS THIS PAGE IS BLANK Copyright © 2006, 2005 New Age International (P) Ltd., Publishers Published by New Age International (P) Ltd., Publishers All rights reserved. No part of this ebook may be reproduced in any form, by photostat, microfilm, xerography, or any other means, or incorporated into any information retrieval system, electronic or mechanical, without the written permission of the publisher. All inquiries should be emailed to [email protected] ISBN (10) : 81-224-2349-3 ISBN (13) : 978-81-224-2349-5 PUBLISHING FOR ONE WORLD NEW AGE INTERNATIONAL (P) LIMITED, PUBLISHERS 4835/24, Ansari Road, Daryaganj, New Delhi - 110002 Visit us at www.newagepublishers.com PREFACE This text, ‘Telecommunication Switching and Networks’ is intended to serve as a one- semester text for undergraduate course of Information Technology, Electronics and Communi- cation Engineering, and Telecommunication Engineering. This book provides in depth knowl- edge on telecommunication switching and good background for advanced studies in communi- cation networks. The entire subject is dealt with conceptual treatment and the analytical or mathematical approach is made only to some extent. For best understanding, more diagrams (202) and tables (35) are introduced wherever necessary in each chapter. The telecommunication switching is the fast growing field and enormous research and development are undertaken by various organizations and firms. The communication networks have unlimited research potentials. Both telecommunication switching and communication networks develop new techniques and technologies everyday. This book provides complete fun- damentals of all the topics it has focused. However, a candidate pursuing postgraduate course, doing research in these areas and the employees of telecom organizations should be in constant touch with latest technologies.
    [Show full text]
  • Analog Access to the Telephone Network
    Telecommunications Telephony Analog Access to the Telephone Network Courseware Sample 32964-F0 Order no.: 32964-00 First Edition Revision level: 01/2015 By the staff of Festo Didactic © Festo Didactic Ltée/Ltd, Quebec, Canada 2001 Internet: www.festo-didactic.com e-mail: [email protected] Printed in Canada All rights reserved ISBN 978-2-89289-541-4 (Printed version) Legal Deposit – Bibliothèque et Archives nationales du Québec, 2001 Legal Deposit – Library and Archives Canada, 2001 The purchaser shall receive a single right of use which is non-exclusive, non-time-limited and limited geographically to use at the purchaser's site/location as follows. The purchaser shall be entitled to use the work to train his/her staff at the purchaser's site/location and shall also be entitled to use parts of the copyright material as the basis for the production of his/her own training documentation for the training of his/her staff at the purchaser's site/location with acknowledgement of source and to make copies for this purpose. In the case of schools/technical colleges, training centers, and universities, the right of use shall also include use by school and college students and trainees at the purchaser's site/location for teaching purposes. The right of use shall in all cases exclude the right to publish the copyright material or to make this available for use on intranet, Internet and LMS platforms and databases such as Moodle, which allow access by a wide variety of users, including those outside of the purchaser's site/location.
    [Show full text]
  • Maintenance News Index
    Editor: Ron Quinney (ES5.4.3) Published by BTHO/NE/ES5.4.3 Room1230, 207 Old Street LONDON EC1V9PS 01 -739 3464 Ext. 7695 Maintenance News ISSN 0143-6627 Produced by Management Communications ( BTHO /PR3.1.5) Maintenance News Index ISSUE 1 1 981 This Maintenance News index is divided alphabetically under subject headings, and articles are listed under these in publication date order. Space has been left to allow readers to update their own index as future articles are published. Where the content of an article is not clear from its title, clarification is given in brackets. For completeness some articles have more than one entry in the index, for example, Those Gas Leaks (MN 7 p10) appears under 'Underground' and 'Safety'. The intention is to re-issue the index every two years. Editor. Issue page Issue page Coin boxes Answer to the 3300B Indicator Problem 10 25 Digital Timer for Coinbox Mechanisms 2 20 Secrets of Line 6 (A51 Telephone Instrument Faults) 12 3 Call Office Maintenance in Midland Region 6 6 Automatic Callmakers 1 2 10 News on Call Offices 10 1 6 Keyphones and MF Signalling- Glasgow Area's Tester 13 30 Call Offices-Customers and Complaints 1 3 2 Key System 4+ 12- Proprietary SBS 16 29 Maintenance Thoughts on New Coinboxes 18 27 How Much Does A Fault Report Cost Now? 17 9 Special Range Telephones-Maintenance 17 25 Herald Call Connect System 19 30 Microphone Inset 21A 19 18 Customers' apparatus PABXs- See 'Exchanges PABX' 1\Jo Access Cards-A108 (m) 1 1 2 Subscribers Apparatus Maintenance Policy 2 17 Data and Datel Keyphones 3
    [Show full text]
  • FT2232D DUAL USB to SERIAL UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI# 127
    Document No.: FT_000173 FT2232D DUAL USB TO SERIAL UART/FIFO IC Datasheet Version 2.05 Clearance No.: FTDI# 127 Future Technology Devices International Ltd FT2232D Dual USB to Serial UART/FIFO IC The FT2232D is a dual USB to serial UART or Fully assisted hardware or X-On / X-Off FIFO interface with the following advanced software handshaking. features: UART Interface supports 7/8 bit data, 1/2 stop Single chip USB to dual channel serial / parallel bits, and Odd/Even/Mark/Space/No Parity. ports with a variety of configurations. Operational configuration mode and USB Entire USB protocol handled on the chip. No Description strings configurable in external USB specific firmware programming required. EEPROM over the USB interface. Transfer Data Rate 300 to 3 Mbaud. USB to parallel FIFO transfer data rate up to 1 Low operating and USB suspend current. megabyte / second. Multi-Protocol Synchronous Serial Engine Supports bus powered, self powered and high- (MPSSE) to simplify synchronous serial power bus powered USB configurations. 2 protocol (USB to JTAG, USB to I C, USB to UHCI/OHCI/EHCI host controller compatible. SPI) design. CPU-style FIFO interface mode simplifies CPU USB 2.0 Full Speed (12Mbits/Second) interface design. compatible. MCU host bus emulation mode configuration Extended -40°C to 85°C industrial operating option. temperature range. Fast Opto-Isolated serial interface option. Compact 48-LD Lead Free LQFP package FTDI‟s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the +4.35V to +5.25V single supply operating requirement for USB driver development in voltage range.
    [Show full text]
  • Inventing the Communications Revolution in Post-War Britain
    Information and Control: Inventing the Communications Revolution in Post-War Britain Jacob William Ward UCL PhD History of Science and Technology 1 I, Jacob William Ward, confirm that the work presented in this thesis is my own. Where information has been derived from other sources, I confirm that this has been indicated in the thesis. 2 Abstract This thesis undertakes the first history of the post-war British telephone system, and addresses it through the lens of both actors’ and analysts’ emphases on the importance of ‘information’ and ‘control’. I explore both through a range of chapters on organisational history, laboratories, telephone exchanges, transmission technologies, futurology, transatlantic communications, and privatisation. The ideal of an ‘information network’ or an ‘information age’ is present to varying extents in all these chapters, as are deployments of different forms of control. The most pervasive, and controversial, form of control throughout this history is computer control, but I show that other forms of control, including environmental, spatial, and temporal, are all also important. I make three arguments: first, that the technological characteristics of the telephone system meant that its liberalisation and privatisation were much more ambiguous for competition and monopoly than expected; second, that information has been more important to the telephone system as an ideal to strive for, rather than the telephone system’s contribution to creating an apparent information age; third, that control is a more useful concept than information for analysing the history of the telephone system, but more work is needed to study the discursive significance of ‘control’ itself. 3 Acknowledgements There are many people to whom I owe thanks for making this thesis possible, and here I can only name some of them.
    [Show full text]
  • Telecommunications Reform in Germany: Lessons and Priorities
    TELECOMMUNICATIONS t REFORM IN GERMANY: LESSONS AND PRIORITIES Bonn, Germany Conference Repor 20 November 1997 American Institute for Contemporary German Studies The Johns Hopkins University Conference Report TELECOMMUNICATIONS REFORM IN GERMANY: LESSONS AND PRIORITIES Bonn, Germany 20 November 1997 American Institute for Contemporary German Studies The Johns Hopkins University The American Institute for Contemporary German Studies (AICGS) is a center for advanced research, study, and discussion on the politics, culture, and society of the Federal Republic of Germany. Established in 1983 and affiliated with The Johns Hopkins University but governed by its own Board of Trustees, AICGS is a privately incorporated institute dedicated to independent, critical, and comprehensive analysis and assessment of current German issues. Its goals are to help develop a new generation of American scholars with a thorough understanding of contemporary Germany, deepen American knowledge and understanding of current German developments, contribute to American policy analysis of problems relating to Germany, and promote interdisciplinary and comparative research on Germany. Executive Director: Jackson Janes Research Director: Carl Lankowski Board of Trustees, Cochair: Steven Muller Board of Trustees, Cochair: Harry J. Gray The views expressed in this publication are those of the author(s) alone. They do not necessarily reflect the views of the American Institute for Contemporary German Studies. ©1998 by the American Institute for Contemporary German Studies ISBN 0-941441-37-7 This AICGS Conference Report paper is made possible through grants from the German Program for Transatlantic Relations, AT&T and o.tel.o communications GmbH. Additional copies are available at $5.00 each to cover postage and processing from the American Institute for Contemporary German Studies, Suite 420, 1400 16th Street, NW, Washington, D.C.
    [Show full text]
  • IBM SDK, Java Technology Edition, Version 6: Windows User Guide Preface
    IBM SDK, Java Technology Edition Version 6 Windows User Guide IBM IBM SDK, Java Technology Edition Version 6 Windows User Guide IBM Note Before you use this information and the product it supports, read the information in “Notices” on page 123. Copyright information This edition of the user guide applies to the IBM SDK, Java Technology Edition, Version 6, for all supported 32-bit Windows architectures, and to all subsequent releases, modifications, and service refreshes, until otherwise indicated in new editions. The platforms this guide applies to are: v IBM 32-bit SDK for Windows, Java Technology Edition, Version 6 v IBM 32-bit Runtime Environment for Windows, Java Technology Edition, Version 6 Note: The SDK and Runtime Environment are available only as part of an IBM product or service. Portions © Copyright 1997, 2016, Oracle and/or its affiliates. © Copyright IBM Corporation 2003, 2016. US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp. Contents Preface ............... v Java Debugger (JDB) .......... 32 Selective debugging .......... 33 Chapter 1. Overview ......... 1 Determining whether your application is running on a 32-bit or 64-bit JVM ........... 34 Version compatibility ........... 1 | Determining which JVM version your application is Migrating from earlier IBM SDK or JREs ..... 1 | running on .............. 34 Supported environments .......... 2 How the JVM processes signals........ 35 Signals used by the JVM ......... 36 Chapter 2. Contents of the SDK and Linking a native code driver to the Runtime Environment ......... 5 signal-chaining library .......... 36 Contents of the Runtime Environment ...... 5 Writing JNI applications .......... 37 Contents of the SDK ...........
    [Show full text]
  • UNIT-V Embedded Communications Protocols and Internet of Things
    UNIT-V Embedded Communications Protocols and Internet of Things COMMUNICATION: Communication between electronic devices is like communication between humans. Both sides need to speak the same language. In electronics, these languages are called communication protocols. Luckily for us, there are only a few communication protocols we need to know when building most electronics projects. In this series of articles, we will discuss the basics of the three most common protocols: SPI, I2C and UART. SPI, I2C, and UART are quite a bit slower than protocols like USB, Ethernet, Bluetooth, and Wi-Fi, but they’re a lot simpler and use less hardware and system resources. SPI, I2C, and UART are ideal for communication between microcontrollers and between microcontrollers and sensors where large amounts of high speed data don’t need to be transferred. DATA COMMUNICATION TYPES: (1) PARALLEL (2) SERIAL: (I) ASYNCHRONOUS (II) SYNCHRONOUS Parallel Communication: In parallel communication, all the bits of data are transmitted simultaneously on separate communication lines. Used for shorter distance. In order to transmit n bit, n wires or lines are used. More costly. Faster than serial transmission. Data can be transmitted in less time. Example: printers and hard disk Serial Communication Basics: In serial communication the data bits are transmitted serially one by one i.e. bit by bit on single communication line It requires only one communication line rather than n lines to transmit data from sender to receiver. Thus all the bits of data are transmitted on single lines in serial fashion. Less costly. Long distance transmission. Example: Telephone. Serial communication uses two methods: Asynchronous.
    [Show full text]
  • Cherry Trail Soc
    Cherry Trail SoC External Design Specification (EDS) (Volume 1 of 2) For Volume 2 of 2 refer Document ID: 543698 June 2014 Revision 1.2 Intel Confidential Document Number: 539071 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. A “Mission Critical Application” is any application in which failure of the Intel Product could result, directly or indirectly, in personal injury or death. SHOULD YOU PURCHASE OR USE INTEL'S PRODUCTS FOR ANY SUCH MISSION CRITICAL APPLICATION, YOU SHALL INDEMNIFY AND HOLD INTEL AND ITS SUBSIDIARIES, SUBCONTRACTORS AND AFFILIATES, AND THE DIRECTORS, OFFICERS, AND EMPLOYEES OF EACH, HARMLESS AGAINST ALL CLAIMS COSTS, DAMAGES, AND EXPENSES AND REASONABLE ATTORNEYS' FEES ARISING OUT OF, DIRECTLY OR INDIRECTLY, ANY CLAIM OF PRODUCT LIABILITY, PERSONAL INJURY, OR DEATH ARISING IN ANY WAY OUT OF SUCH MISSION CRITICAL APPLICATION, WHETHER OR NOT INTEL OR ITS SUBCONTRACTOR WAS NEGLIGENT IN THE DESIGN, MANUFACTURE, OR WARNING OF THE INTEL PRODUCT OR ANY OF ITS PARTS. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined”.
    [Show full text]
  • Intel Atom® Processor Z3600 and Z3700 Series Datasheet, Vol 1
    Intel® Atom™ Processor Z3600 and Z3700 Series Datasheet December 2014 Revision 003 Document Number: 329474-003 You may not use or facilitate the use of this document in connection with any infringement or other legal analysis concerning Intel products described herein. You agree to grant Intel a non-exclusive, royalty-free license to any patent claim thereafter drafted which includes subject matter disclosed herein. No license (express or implied, by estoppel or otherwise) to any intellectual property rights is granted by this document. The products described may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. All information provided here is subject to change without notice. Contact your Intel representative to obtain the latest Intel product specifications and roadmaps. Copies of documents which have an order number and are referenced in this document may be obtained by calling 1-800-548- 4725 or visitwww.intel.com/design/literature.htm. Intel, Intel Atom and the Intel logo, are trademarks of Intel Corporation in the U.S. and/or other countries. *Other names and brands may be claimed as the property of others. See Trademarks on intel.com for full list of Intel trademarks. © 2014 Intel Corporation. 2 Datasheet Contents 1Introduction............................................................................................................ 16 1.1 Terminology ....................................................................................................
    [Show full text]
  • TXE-Xxx-KH Manual 12-31-04.Qxd
    TXE-315-KH TXE-418-KH TXE-433-KH WIRELESS MADE SIMPLE KH SERIES TRANSMITTER/ENCODER DATA GUIDE DESCRIPTION The KH Series is ideally suited for volume use in OEM applications such as remote 1.220" control/command and keyless entry. It combines a highly optimized RF transmitter with an on-board encoder. When paired with a 0.630" RF TRANSMITTER/ENCODER matching KH series receiver / decoder module, TXE-418-KH a highly reliable wireless link is formed, capable LOT 2000 of transferring the status of 8 parallel inputs for distances in excess of 300 feet. Ten tri-state address lines provide 310 addresses for security and uniqueness. Housed in a compact 0.18" SMD package, the KH transmitter utilizes a SAW architecture to achieve an unmatched blend of performance, size, and cost. No Figure 1: Package Dimensions external RF components, except an antenna, are required, making integration straightforward. FEATURES Low cost Ultra-low power consumption On-board encoder Compact SMD Package 8 parallel binary outputs Stable SAW-based architecture 310 addresses for security and Adjustable output power uniqueness Transmit enable line No external RF components No production tuning required APPLICATIONS INCLUDE Remote Control / Command ORDERING INFORMATION Keyless Entry PART # DESCRIPTION Garage / Gate Openers EVAL-***-KH Basic Evaluation Kit Lighting Control TXE-315-KH Transmitter 315 MHz Call Systems TXE-418-KH Transmitter 418 MHz Home / Industrial Automation TXE-433-KH Transmitter 433 MHz Fire / Security Alarms RXD-315-KH Receiver 315 MHz Remote Status Monitoring RXD-418-KH Receiver 418 MHz Wire Elimination RXD-433-KH Receiver 433 MHz *** Insert Frequency Transmitters are supplied in tubes of 20 pcs.
    [Show full text]
  • On the Electric Telegraph, and the Principal Improve- Ments in Its Construction.” by FREDERICRRICH.4RD WINDOW, Assoc
    THETELEGRAPII. ELECTRIC 329 In the year 1848, there were but six thousand miles in operation ; so that in three years the amount has been nearly quintupled. Theelectric telegraph is now extendingin all directions,new lines are being constantly opened, and new proofs of its wonderful powers are recorded. The Dover Straithas been successfully crossed, and the continental nations are extending the system, as rapidly as their finances willpermit; the governments of Austria,Prussia, Bavaria,and Saxony, are adopting a general tariff, for messages transmittedthroughout their dominions. Russia is contemplating the connexion of its capital on the Baltic,with its ports on the Black Sea,while a stillampler conception presents itself, in which tire great lines of Eastern Europe may form but a link in the chain of general telegraphic communication. However premature, or sanguine, the expressionof these views may now appear, one fact is certain ; the electric telegraph is but in its infancy, and will yet become a powerful agent, in promoting the cause of civilization and the preservation of unity, peace and good-will throughout the world. NO.863.-“ On the Electric Telegraph, and the principal improve- ments in its Construction.” By FREDERICRRICH.4RD WINDOW, Assoc. Inst. C.E. THEnecessity of a means of communicating intelligence of events happening in any place, to another point at a distance, in a time less than that in which thedistance could be travelled, has been felt from the most remote ages ; and even among theearliest records there are instances of contrivauces for accomplishing this end, with more, or less certainty and success.
    [Show full text]