Federal Motor Vehicle Theft Prevention Standard

Total Page:16

File Type:pdf, Size:1020Kb

Federal Motor Vehicle Theft Prevention Standard 24402 Federal Register / Vol. 76, No. 84 / Monday, May 2, 2011 / Rules and Regulations benefit a CA in any manner that is based motor vehicles. E-mail is now included Facility (Docket No. NHTSA–2009– upon the number of VRS minutes or as a means to submit the target area 0069) which is accessible at: http:// calls that the CA relays, either designations. Under the Theft www.regulations.gov. Through this individually or as part of a group. Prevention Standard, manufacturers of technical amendment, manufacturers (4) Remote training session calls. VRS high theft passenger motor vehicle lines will have several options when calls to a remote training session or a subject to parts marking, and providing the target area information: comparable activity will not be manufacturers of replacement parts electronic means through the portal compensable from the TRS Fund when designed for high theft lines, must http://www.regulations.gov; paper the provider submitting minutes for submit designation of target areas for copies (via US mail, private courier or such a call has been involved, in any identifying numbers to be marked on hand delivery) to Docket Management at manner, with such a training session. each major part and symbols to be 1200 New Jersey Avenue, SE., Such prohibited involvement includes marked on each major replacement part. (NHTSA’s new address); or faxing the training programs or comparable This rulemaking makes no substantive information. activities in which the provider or any changes to the Theft Prevention Through these new means, it is affiliate or related party thereto, Standard. anticipated that the public will be able including but not limited to its DATES: This final rule becomes effective to view target area information much subcontractors, partners, employees or June 1, 2011. more quickly than was the case in the past. Because the information may go sponsoring organizations or entities, has FOR FURTHER INFORMATION CONTACT: Ms. directly to a publicly reviewable docket, any role in arranging, scheduling, Carlita Ballard, NHTSA, 1200 New (i.e., NHTSA–2009–0069), NHTSA does sponsoring, hosting, conducting or Jersey Ave., SE., Rm. W43–439, NVS– not advise that manufacturers send any promoting such programs or activities. 131, Washington, DC 20590. Ms. information for which a manufacturer * * * * * Ballard’s telephone number is: (202) wishes to assert confidential treatment ■ 366–0846. 5. In § 64.606, revise paragraph (g) to to Docket Management or to http:// read as follows: SUPPLEMENTARY INFORMATION: 49 CFR www.regulations.gov. In the event that a Part 541, Federal Motor Vehicle Theft § 64.606 VRS and IP Relay provider and manufacturer wishes the target location Prevention Standard, specifies that data to be treated as confidential TRS program certification. 1 major parts and major replacement information prior to the release of a new * * * * * parts of motor vehicles subject to the (g) VRS and IP Relay providers model, it should submit the theft area standard must be marked in accordance data to NHTSA’s Office of the Chief certified under this section shall file with Section 541.5, for passenger motor with the Commission, on an annual Counsel and request confidential vehicles, and Section 541.6 for treatment as set forth in 49 CFR Part 512 basis, a report providing evidence that replacement parts. The standard they are in compliance with § 64.604. Confidential Business Information. specifies that each manufacturer that is Because confidential target location data VRS providers shall include within the original producer that installs or these annual submissions a description will become public when a new model assembles the covered major parts on a is released for sale, sections 541.5(e)(2) of all agreements in connection with line shall designate a target area for the marketing and outreach activities, and 541.6(e)(3) also require submission identifying numbers to be marked on of the target location data within seven including those involving sponsorship, each major part. For replacement parts, financial endorsements, awards, and days after the information has been the standard specifies that each made public or the new vehicle line has gifts made by the provider to any manufacturer that is the original individual or entity. been released for sale to the public, producer or assembler of the vehicle for whichever comes first. [FR Doc. 2011–10342 Filed 4–29–11; 8:45 am] which the replacement part is designed This change will not make any BILLING CODE 6712–01–P shall designate a target area for the substantive changes to the Theft identifying symbols to be marked on Prevention Standard and will not each replacement part for a major part. impose any additional substantive DEPARTMENT OF TRANSPORTATION At present, Part 541 specifies that requirements or burdens on designation of target areas is to be manufacturers. Therefore, NHTSA finds National Highway Traffic Safety submitted to: Administrator, National for good cause that a notice of proposed Administration Highway Traffic Safety Administration, rulemaking and opportunity for 400 Seventh Street, SW., Washington, comment on these amendments are not 49 CFR Part 541 DC 20590. NHTSA has moved, and this necessary. In addition, this final rule [Docket No. NHTSA–2009–0069] address is no longer applicable. This will change the address to which technical amendment updates NHTSA’s manufacturers will provide target RIN 2127–AK81 address. In addition, to facilitate timely location data, but will have no effect on release of target area information, and to the collection of information burden Federal Motor Vehicle Theft Prevention maximize use of electronic means, the associated with the Theft Prevention Standard target area information henceforth may Standard (See OMB Clearance No. AGENCY: National Highway Traffic be sent to the Docket Management 2127–0539 Procedure for Selecting Lines Safety Administration, DOT. to be Covered by the Theft Prevention 1 ACTION: Final rule; technical Each of the following parts, if present on a motor Standard, expiration date: 6/30/2011). vehicle: engine; transmission; right front fender; left amendment. front fender; hood; right front door; left front door; List of Subjects in 49 CFR Part 541 right rear door; left rear door; sliding or cargo SUMMARY: In this technical amendment, door(s); front bumper; rear bumper; right rear Crime, Labeling, Motor vehicles, the National Highway Traffic Safety quarter panel (passenger cars); left rear quarter Reporting and recordkeeping Administration (NHTSA) updates the panel (passenger cars); right side assembly (MPVs); requirements. left side assembly (MPVs); pickup box and/or cargo address for submission, and the box (LDTs); rear door(s) (both doors in case of In consideration of the foregoing, procedure to submit designation of double doors), decklid, tailgate, or hatchback, NHTSA amends 49 CFR Part 541 as set target areas on high theft major parts of whichever is present. forth below. VerDate Mar<15>2010 16:25 Apr 29, 2011 Jkt 223001 PO 00000 Frm 00060 Fmt 4700 Sfmt 4700 E:\FR\FM\02MYR1.SGM 02MYR1 jlentini on DSKJ8SOYB1PROD with RULES Federal Register / Vol. 76, No. 84 / Monday, May 2, 2011 / Rules and Regulations 24403 PART 541—FEDERAL MOTOR (e)(3) * * * In those instances where from vessels using jig gear and catcher VEHICLE THEFT PREVENTION a manufacturer has submitted this target vessels greater than or equal to 60 feet STANDARD area information to NHTSA with a (18.3 meters) length overall (LOA) using request for confidential treatment under hook-and-line gear to catcher vessels ■ 1. The authority citation for Part 541 49 CFR Part 512, the manufacturer shall less than 60 feet LOA using hook-and- continues to read as follows: also submit a complete copy of the line or pot gear in the Bering Sea and Authority: 49 U.S.C. 33101, 33102, 33013, target area information within seven (7) Aleutian Islands management area. This and 330105; delegation of authority at 49 days after the information has become action is necessary to allow the 2011 CFR 1.50. public or the new line has been released total allowable catch of Pacific cod to be ■ 2. In § 541.5, paragraph (e)(2) is for sale to the public, whichever comes harvested. amended by revising the second first. The information should be DATES: Effective April 30, 2011, through sentence, by adding third and fourth submitted to: Docket Management, 2400 hrs, Alaska local time (A.l.t.), sentences, and paragraphs (e)(2)(i) Room W12–140, Ground Floor, 1200 December 31, 2011. through (iv) are added to read as New Jersey Avenue, SE., Washington, FOR FURTHER INFORMATION CONTACT: follows: DC 20590 by any of the following Obren Davis, 907–586–7228. methods. In all cases, the docket SUPPLEMENTARY INFORMATION: NMFS § 541.5 Requirements for passenger motor number for the submission, (Docket No. manages the groundfish fishery in the vehicles. NHTSA–2009–0069) must be cited. BSAI according to the Fishery * * * * * (i) Electronic submission to the Management Plan for Groundfish of the (e)(2) * * * In those instances where Federal eRulemaking Portal: http:// Bering Sea and Aleutian Islands a manufacturer has submitted this target www.regulations.gov. Follow the Management Area (FMP) prepared by area information to NHTSA with a instructions for submitting information. the North Pacific Fishery Management request for confidential treatment (ii) By U.S. Mail: Docket Management Council under authority of the pursuant to 49 CFR Part 512, the Facility: U.S. Department of Magnuson-Stevens Fishery manufacturer must also submit a Transportation, 1200 New Jersey Conservation and Management Act. complete copy of the target area Avenue, SE., West Building, Ground Regulations governing fishing by U.S. information within seven (7) days after Floor, Room W12–140, Washington, DC vessels in accordance with the FMP the information becomes public, or the 20590. appear at subpart H of 50 CFR parts 600 new line is released for sale to the (iii) Hand delivery or by courier: 1200 and 679.
Recommended publications
  • The Effects of Retroreflective Conspicuity Tape on Motorcycle Detection Distance Among Car Drivers
    International Journal of Road Safety 1(1) 2020: 20-25 ________________________________________________________________________________________________________ International Journal of Road Safety Journal homepage: www.miros.gov.my/journal _______________________________________________________________________________________________ The Effects of Retroreflective Conspicuity Tape on Motorcycle Detection Distance among Car Drivers Muhamad Syukri Abdul Khalid1,*, Mohd Hafzi Md Isa2, Azhar Hamzah1, Mohd Syazwan Solah1, Aqbal Hafeez Ariffin1, Noor Faradila Paiman1, Zulhaidi Mohd Jawi1, Muhammad Ruhaizat Abd Ghani3, Khairil Anwar Abu Kassim1 & Siti Zaharah Ishak2,4 *Corresponding author: [email protected] 1Vehicle Safety & Biomechanics Research Centre, Malaysian Institute of Road Safety Research, 43000 Kajang, Selangor, Malaysia 2Director General’s Office, Malaysian Institute of Road Safety Research, 43000 Kajang, Selangor, Malaysia 3Road Safety Engineering and Environment Research Centre, Malaysian Institute of Road Safety Research, 43000 Kajang, Selangor, Malaysia 4Faculty of Civil Engineering, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor, Malaysia ________________________________________________________________________________________________________ ABSTRACT ARTICLE INFO _____________________________________________________________________ ___________________________ This study was carried out to determine whether or not retroreflective conspicuity tapes installed Article History: onto the side of a motorcycle would
    [Show full text]
  • Consumer Product Safety Commission § 1512.17
    Consumer Product Safety Commission § 1512.17 in) below the point on the seat surface not be peeled or scraped away without that is intersected by the line of the removal of tire material. seat post. The optical axis of the reflec- (3) The retroreflective material shall tor shall be directed rearward within 5° be as resistant to abrasion as is the ad- of the horizontal-vertical alignment of jacent sidewall material so that when the bicycle when the wheels are trav- retroreflective material is removed eling in a straight line, as defined in from the inflated tire by abrasion with § 1512.18(m)(2). The reflectors and/or a wet, steel bristle brush, tire material mounts shall incorporate a distinct, will be removed along with the preferred assembly method that shall retroreflective material. insure that the reflector meets the op- (4) The retroreflective material shall tical requirements of this paragraph (d) be tested for performance in accord- when the reflector is attached to the ance with the retroreflective tire test, bicycle. The rear reflector shall be § 1512.18(o), to assure the reflectance tested in accordance with the reflector properties over the angles given in mount and alignment test, § 1512.18(m). table 3. When a portion of the (e) Pedal reflectors. Each pedal shall retroreflective material is selected have reflectors located on the front and (and the remainder is masked as speci- rear surfaces of the pedal. The reflector fied in § 1512.18(o)(2)(i)), the selected elements may be either integral with portion shall not contact the ground the construction of the pedal or me- plane when the assembled bicycle is chanically attached, but shall be suffi- resting on that plane in any orienta- ciently recessed from the edge of the tion.
    [Show full text]
  • Me Or Body Is Different from the Manufacturer's Specifications, Unless That Difference Is Caused By: A
    MAINE Definitions Altered Vehicle. A motor vehicle with a gross vehicle weight rating of 10,000 pounds or less that is modified so that the distance from the ground to the lowermost point on any part of the frame or body is different from the manufacturer's specifications, unless that difference is caused by: A. The use of tires that are no more than 2 sizes larger than the manufacturer's recommended sizes; B. The installation of a heavy duty suspension, including shock absorbers and overload springs; or C. Normal wear of the suspension system that does not affect control of the vehicle. Antique Auto. An automobile or truck manufactured in or after model year 1916 that is: A. More than 25 years old; B. Equipped with an engine manufactured either at the same time as the vehicle or to the specifications of the original engine; C. Substantially maintained in original or restored condition primarily for use in exhibitions, club activities, parades or other functions of public interest; D. Not used as its owner's primary mode of transportation of passengers or goods; E. Not a reconstructed vehicle; and F. Not an altered vehicle. Classic Vehicle. A motor vehicle that is at least 16 years old but less than 26 years old that the Secretary of State determines is of significance to vehicle collectors because of its make, model and condition and is valued at more than $5,000. Custom Vehicle. A motor vehicle manufactured after model year 1948 that: A. Is at least 25 years old or was manufactured to resemble a motor vehicle that is at least 25 years old; and B.
    [Show full text]
  • Chapter Trans 305
    Published under s. 35.93, Wis. Stats., by the Legislative Reference Bureau. 401 DEPARTMENT OF TRANSPORTATION Trans 305.02 Chapter Trans 305 STANDARDS FOR VEHICLE EQUIPMENT Subchapter I — General Provisions Trans 305.29 Steering and suspension. Trans 305.01 Purpose and scope. Trans 305.30 Tires and rims. Trans 305.02 Applicability. Trans 305.31 Modifications affecting height of a vehicle. Trans 305.03 Enforcement. Trans 305.32 Vent, side and rear windows. Trans 305.04 Penalty. Trans 305.33 Windshield defroster−defogger. Trans 305.05 Definitions. Trans 305.34 Windshields. Trans 305.06 Identification of vehicles. Trans 305.35 Windshield wipers. Trans 305.065 Homemade, replica, street modified, reconstructed and off−road vehicles. Subchapter III — Motorcycles Trans 305.37 Applicability of subch. II. Subchapter II — Automobiles, Motor Homes and Light Trucks Trans 305.38 Brakes. Trans 305.07 Definitions. Trans 305.39 Exhaust system. Trans 305.075 Auxiliary lamps. Trans 305.40 Fenders and bumpers. Trans 305.08 Back−up lamp. Trans 305.41 Fuel system. Trans 305.09 Direction signal lamps. Trans 305.42 Horn. Trans 305.10 Hazard warning lamps. Trans 305.43 Lighting. Trans 305.11 Headlamps. Trans 305.44 Mirrors. Trans 305.12 Parking lamps. Trans 305.45 Sidecars. Trans 305.13 Registration plate lamp. Trans 305.46 Suspension system. Trans 305.14 Side marker lamps, clearance lamps and reflectors. Trans 305.47 Tires, wheels and rims. Trans 305.15 Stop lamps. Trans 305.16 Tail lamps. Subchapter IV — Heavy Trucks, Trailers and Semitrailers Trans 305.17 Brakes. Trans 305.48 Definitions. Trans 305.18 Bumpers.
    [Show full text]
  • Fenders and Sheet Metal
    FEND= AND SHEET METAL 1964 PASSENGER CAR PARTS CATALOG page 12-1 GROUP 12 - FENDERS AND SHEET METAL SHIELD 23-34-121, FENDER 12-01-5 AOLAMP SPLASH SIDE SHIELD 12-04-4 SHIELD 12-04-4 STRAP13-34-3 f RAY 13-33-61 STUD13-36-5 BRACKET 13-33-62 19x9567A FRONT FENDER - VALIANT W1-2 STRAP FRONT FENDER - DART VL1-2 Printed in U.5.A. Page 12-1 March 16, 1064 Supersedes Sept. 6, 1963. FENDERS AND Page 12-2 1964 PASSENGER CAR PARTS CATALOG SHEET METAL SHIELD 23-34-121 SHIELD 12-04-4 STRAP 13-34-3 STUD 13-36-5 TRAY 13-33-61 BRACE [NOT SERVICED) FRONT FENDER - PLYMOUTH VP1-2 FENDER 12-01-5 SHIELD 23-34-121 STRAP 13.34-3 BRACE 12-07-1 (NOT SERVICEDJ SHIELD 12-04-4 \ 'STUD 13-36-5 '-. '-lBRACE(N0T SERVICED] SHIELD 23-32-110- 19x FRONT FENDER - DODGE VD1-2 March 16, 1964 Supersedes Sept. 6, 1963. FENDERS AND smm -AL 1964 PASSENGER CAR PARTS CATALOG page 12-3 FENDER 12-01-5 SHIELD 12-04-4 STRAP 13-34-3 SHIELD 12-04- BRACE 12-07-1 BRACKET 12-04-5 / FRONT FENDER - DODGE VAS SHIELD 12-04-4 STUD 13-36-5 SHIELD 12-04.4 BRACE 12-07-1 STRAP 13-34-3 BRACE 12 -07-1 BRACKET 12-04-5 FRONT FENDER - CHRYSLER VC1-2-3 Printsd in U.S.A. Pape 12-3 September 6, 1063. FEND= AND page 12-4 1964 PASSENGER CAR PARTS CATALOG smzm ,,, BRACE 12-07-1 BRACKET1 STRUT 12-04-25 COVER 1-88-51 ' BRACKET 12-06-3 - STRAP 13-34-3 fl STllD 13-36.5 BRACE lJ-ll-I2< SHIELD 13-06-20 BRACKET 12-04.5 BRACE 13-33-68 \1 FRONT FENDER - IMPERIAL VY1 \;;; >J:I? NOTES September 6, 1963.
    [Show full text]
  • Chassis Catalog
    Parts for Trucks, Trailers & Buses ® BUS PARTS 7 CHASSIS Proven, reliable and always innovative. TRP® offers reliable aftermarket products that are designed and tested to exceed customers’ expectations regardless of the vehicle make, model or age. FENDERS • SUSPENSION & RIDE CONTROL • WHEEL END Tested. Reliable. Guaranteed. TABLE OF CONTENTS Chassis CHASSIS FENDERS Choosing the right Half Fenders - Poly ............................7-5 replacement part or service for your vehicle—whether you own Full Fenders - Poly ............................7-6 one, or a fleet—is one of the Single Axle Fenders - Poly ......................7-7 most important decisions you can make for your business. Super Single Fenders - Half . 7-9 And, with tested TRP® parts Super Single Fenders - Full .....................7-9 it’s an easy decision. Super Single Fenders - Quarter .................7-11 Regardless of the make you drive, TRP® quality Half Fenders ................................7-13 replacement parts are Full Fenders ................................7-17 engineered to fit your truck, trailer or bus. Choose the Single Axle Fenders ..........................7-21 parts that give you the best Quarter Fenders . 7-26 value for your business. Check them out at an approved Fender Mounting Kits .........................7-29 ® TRP retailer near you. Top Flap for Quarter Fender ....................7-39 Mudflap Hangers ............................7-40 The cross reference information in this catalog is based upon data provided by several industry sources and our partners. While every attempt is made to ensure the information presented is accurate, we bear no liability due to incorrect or incomplete information. Product Availability Due to export restrictions and market ® demands, not all products are TRP North America always available in every location.
    [Show full text]
  • Highmark Fender Flares Ram Hd Front
    HIGHMARK FENDER FLARES RAM HD FRONT AEV30118AC Last Updated: 12/16/16 INSTALLATION GUIDE INSTALLATION PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING ANY WORK. THESE INSTRUCTIONS ASSUME A CERTAIN AMOUNT OF MECHANICAL ABILITY AND ARE NOT WRITTEN NOR INTENDED FOR SOMEONE NOT FAMILIAR WITH AUTO REPAIR. INCLUDED PARTS REQUIRED TOOLS Flare RH Basic hand tools Flare LH Hammer Bumper Extension RH Drill Bumper Extension LH Drill bits - 1/4, 7/16, 1/2, 13/32, 3/4 Wheel Liner RH Rivet gun Wheel Liner LH Plastic rivet gun Fastener Pack Wire strippers LED Lamp Kit Air saw Mounting Bracket Kit Cut off wheel Rocker Panel Trim Templates Grinder Dill Templates Vise Wax & grease remover Rust preventer Silicone ii Front flare installation I. Remove factory components 1. Remove the factory wheel flares (if equipped) and wheel liners (fig. 1). 2. Remove foam inserts (fig. 2). CHRISTMAS TREE Figure 1 Figure 2 3. Remove Grill. 4. Remove headlights and attaching brackets. SAVE all hardware (fig. 3). Figure 3 5. Remove any badges on fender. 1 II. Prepare for cutting 1. Protect fenders, doors, hood, and windshield using crash wrap or welding blankets. Sparks from cut- ting can damage paint and glass. 2. Reposition wire harnesses on driver and passenger sides. A. Remove all body mount bolts along the driver side (fig. 4). B. Wire harnesses will be repositioned on the interior side of the driver-side frame rail (fig. 5). Figure 4 Figure 5 C. Lift cab off of frame just enough to slip wire harnesses to the other side of the body mount.
    [Show full text]
  • New Jersey Administrative Code Title 13, Chapter 20
    NEW JERSEY ADMINISTRATIVE CODE TITLE 13, CHAPTER 20, SUBCHAPTER 32 INSPECTION STANDARDS AND TEST PROCEDURES TO BE USED BY OFFICIAL INSPECTION FACILITIES Amendment Adopted: September 15, 2009 Effective: October 19, 2010 Operative: January 1, 2010 See: 41 N.J.R. 3939(b) TABLE OF CO~TE:--ITS 13:20-32.1 Ddinitions 13:20-32.2 General provisions; official inspection facilities 13:20-323 Cn·dcntials; official inspection facilities 13:20-32.-t License plates; official inspection facilities 13:20-32.5 Steering and suspension; official inspection facilities 13:20-32.6 Front parking lights; official inspection facilities 13:20-32.7 Glazing; official inspection facilities 13:20-32.8 Obstruction to driver's vision; official inspection facilities 13:20-32.9 Horn: official inspection facilities 13:20-32.10 Windshield wipers; official inspection facilities 13:20-32.11 Clcanmce lights; official inspection facilities 13:20-32.12 Turn signals and hazard waming signals; official inspection facilities 13:20-32.13 Reflectors; official inspection facilities 1J:20-32.1-t Identification lights; official inspection facilities IJ:20-32.15 Side-marker lights; official inspection facilities 13:20-32.16 Taillights and license plate light; ofticial inspection facilities 13:20-32.17 Stoplights; official inspection facilities 13:20-32.18 \Vhecls; official inspection facilities 13:20-32.19 Tires; official inspection facilities 13:20-32.20 Exhaust system; official inspl·ction facilities 13:20-32.21 Prescdhed emission or on-hoard diagnostics test(s); official inspection
    [Show full text]
  • Motorcycle Inspections
    PERIODIC MOTOR VEHICLE INSPECTION MANUAL FOR INSPECTORS OF MOTORCYCLES DEPARTMENT OF TRANSPORTATION STATE OF HAWAII AUGUST 2005 TABLE OF CONTENTS Alphabetical by Components Alignment ................................................................................................................1 Battery......................................................................................................................2 Brakes ......................................................................................................................2 Cables.......................................................................................................................4 Clutch ......................................................................................................................4 Controls & Indicators...............................................................................................4 Engine ......................................................................................................................4 Exhaust System........................................................................................................5 Fenders.....................................................................................................................5 Final Drive ...............................................................................................................6 Footrests...................................................................................................................6 Frame .......................................................................................................................6
    [Show full text]
  • NSN Part Number Description 1010015263418 3307129 BRACE
    NSN Part Number Description 1010015263418 3307129 BRACE,ARMAMENT MOUNT 1240014710018 2058200 CAP,OVERFLOW TANK 1350000387715 1389660 SOCKET,PANEL LIGHT 2010015635614 3904972 MODULE,ENG,C15,FLASHED,ASSY 2040011841899 1450130U SHEAVE ASSEMBLY 2320015727956 95SK153 KIT,MTVR REDUCED HGT CAB HRDWR 2320015727969 95SK154 KIT,WEAPON MOUNT HARDWARE 2320015727976 95SK164 KIT,HARDWARE,RHA,CAB&WEAPON MT 2320015982051 3411762 PLATFORM DECKING ASSEMBLY 2510001160458 EE36224 GUIDE,DOVETAIL,FEMALE 2510001163196 345FX6 HOOD HOOK 2510001434354 57613BX PIN SHACKLE MTG 2510010394396 EE36228 GUIDE,DOVETAIL MALE,CAB DOOR 2510010554489 19AS679 SPRING ASSEMBLY 2510010637622 53408BX PIN-SPRG EYE 2510010877156 100YW39 LOCK ASSY 2510011027521 19AS571 TOP PAD 2510011282320 2AD729 GLASS, SLIDING 2510011324983 1313230 SHOCK ABSORBER 2510011493784 1316090W SKID PLATE,MOUNT,LOWER 2510011507786 1316020W STRUCTURE FRAME ASSY 2510011525569 1309810U DOOR ASSY,LH 2510011525570 2AN106 PLATE MAIN 2510011527759 1368090W PANEL ASSY,FENDER 2510011527761 1328840 PANEL,FENDER,FRONT,LH 2510011527765 1332360W GRAB HANDLE,WLDMT 2510011527775 1326720W ASSY,LEG 2510011527822 1325940W HOOD PANEL,SIDE,WLDMT 2510011527903 1323940W 5TH WHEEL 3.5IN KINGPIN,WLDMT 2510011532735 19AS65 SADDLE CAP 2510011532738 19AS268 TORQUE ROD MOUNT,CASTING 2510011538450 2HK435 SHOCK ABSORBER 2510011541288 1357830 PLATE,MTG 2510011542101 1315090W DECKING,REAR 2510011542123 1327520W BRACE,FENDER,LH 2510011544715 1350550W SKID PLATE SUPPORT,LH 2510011548145 1302040 SPRING AND SADDLE 2510011554146 1322400W ENGINE
    [Show full text]
  • 109 Part 541—Federal Motor Vehi- Cle Theft Prevention Stand
    Nat’l Highway Traffic Safety Admin., DOT § 541.4 TABLE I—GALLON EQUIVALENT MEASUREMENTS (a) Passenger motor vehicle parts FOR GASEOUS FUELS PER 100 STANDARD identified in § 541.5(a) that are present: CUBIC FEET—Continued (1) In the passenger motor vehicle lines listed in appendix A of this part; Gallon equivalent Fuel measurement (2) Beginning with model year 1997, in passenger motor vehicle lines which Hythane (Hy5) ......................................... 0.741 NHTSA has finally determined, pursu- * Per gallon unit of measure. ant to 49 CFR part 542, to be high theft based on the 1990/91 median theft rate; PART 541—FEDERAL MOTOR VEHI- and CLE THEFT PREVENTION STAND- (3) Beginning with model year 1997, in ARD passenger motor vehicle lines listed in appendix B of this part. Sec. (b) Replacement parts for passenger 541.1 Scope. 541.2 Purpose. motor vehicle lines described in 541.3 Application. § 541.3(a) (1) and (2), if the part is identi- 541.4 Definitions. fied in § 541.5(a). 541.5 Requirements for passenger motor ve- hicles. [59 FR 64168, Dec. 13, 1994] 541.6 Requirements for replacement parts. APPENDIX A TO PART 541—LINES SUBJECT TO § 541.4 Definitions. THE REQUIREMENTS OF THIS STANDARD (a) Statutory terms. All terms defined APPENDIX A–I TO PART 541—HIGH-THEFT in 49 U.S.C. chapter 331 are used in ac- LINES WITH ANTITHEFT DEVICES WHICH cordance with their statutory mean- ARE EXEMPTED FROM THE PARTS-MARK- ING REQUIREMENTS OF THIS STANDARD ings unless otherwise defined in para- PURSUANT TO 49 CFR PART 543 graph (b) of this section.
    [Show full text]
  • Strength and Stiffness Analysis of Motorcycle Frame Master’S Final Degree Project
    Kaunas University of Technology Faculty of Mechanical Engineering and Design Strength and Stiffness Analysis of Motorcycle Frame Master’s Final Degree Project Hadi Slaiman Project author Assoc. Prof. Dr. Paulius Griskevicius Supervisor Kaunas, 2018 Kaunas University of Technology Faculty of Mechanical Engineering and Design Strength and Stiffness Analysis of Motorcycle Frame Master’s Final Degree Project Vehicle Engineering (621E20001) Hadi Slaiman Project author Assoc. Prof. Dr. Paulius Griskevicius Supervisor Assoc. Prof. Dr. Zilvinas Bazaras Reviewer Kaunas, 2018 Kaunas University of Technology Faculty of Mechanical Engineering and Design Hadi Slaiman Strength and Stiffness Analysis of Motorcycle Frame Declaration of Academic Integrity I confirm that the final project of mine, Hadi Slaiman, on the topic ‘’ Strength and stiffness analysis of motorcycle frame “is written completely by myself; all the provided data and research results are correct and have been obtained honestly. None of the parts of this thesis have been plagiarised from any printed, Internet-based or otherwise recorded sources. All direct and indirect quotations from external resources are indicated in the list of references. No monetary funds (unless required by law) have been paid to anyone for any contribution to this project. I fully and completely understand that any discovery of any manifestations/case/facts of dishonesty inevitably results in me incurring a penalty according to the procedure(s) effective at Kaunas University of Technology. (name and surname filled
    [Show full text]