DOCSLIB.ORG

Gigawatt Pulsed Power Technologies and Applications

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Gigawatt Pulsed Power Technologies and Applications Gigawatt Pulsed Power Technologies and Applications Patrik Appelgren Doctoral Thesis School of Electrical Engineering Space and Plasma Physics Royal Institute of Technology Stockholm, Sweden 2011 KTH School of Electrical Engineering Space and Plasma Physics TRITA-EE 2011:034 Royal Institute of Technology ISSN 1653-5146 SE-100 44 Stockholm ISBN 978-91-7415-962-2 Sweden Akademisk avhandling som med tillstånd av Kungl Tekniska Högskolan framlägges till offentlig granskning för avläggande av teknologie doktorsexamen i fysikalisk elektroteknik den 20:e maj 2011 kl. 10.00 i sal F3, Lindstedtsvägen 26, Kungliga Tekniska Högskolan, Stockholm. © Patrik Appelgren, maj 2011 Tryck: Universitetsservice US AB iii Gigawatt Pulsed Power Technologies and Applications Patrik Appelgren Abstract This thesis summarizes work on electrical pulsed power technologies and applications of very high electric power, of gigawatt levels, and involving high explosives. One pulsed power technology studied utilizes high explosives to generate electromagnetic energy while one application studied uses electromagnetic energy to disrupt fast-moving metal jets created using high explosives. The pulsed power source studied is a helical explosively driven magnetic flux compression generator. This kind of device converts the chemically stored energy in a high explosive into electromagnetic energy in the form of a powerful current pulse. Two generators were studied in order to investigate their performance and to understand their operation. An electrical circuit model was used to simulate the electrical behaviour and a hydrocode was used to simulate the explosion and mechanical deformation of the device. The experimental results obtained were peak currents of 269 kA and 436 kA corresponding to current amplification ratios of 47 and 39. The general shape of the measured and simulated current pulses was in good agreement and the simulated peak currents did not deviate more than 1 % from the measured peak currents. The other application studied is a protection technology against anti-tank warheads with shaped charges. A shaped charge is a device that creates a metal jet travelling at high velocity capable of penetrating several decimetres of steel armour. A powerful current pulse may be passed through the jet and due to iv heating and magnetic forces, the jet may be disrupted and its penetrative capability significantly reduced. A series of experiments has been performed to investigate the physical phenomena and a disruption process is suggested. Descriptors Magnetic Flux Compression, Explosives, Pulsed Power, Shaped Charges, Electric Armour, Circuit Simulations, Hydrodynamic simulations v Preface This work was carried out at the Swedish Defence Research Agency, FOI, Division of Defence & Security, Systems and Technology. Part of the work was performed within a research program on pulsed power technology for electromagnetic weapons, and part was performed within a research program on future armour protection. The work was funded by the Swedish Armed Forces. vi vii Acknowledgements First of all I would like to thank Gert Bjarnholt. He was the designer of the explosive flux compression generator and was managing the FOA (now FOI) project in this research area. Fortunately, for me, only one of the three generators manufactured was exploded. Two generators remained unused and during the last year before his retirement, Gert and I fired the two generators, covered with various measurement devices, very successfully. The second part of my doctoral work was research on electric armour, a novel technology for protection of military vehicles against shaped charge warheads. Thank you, Melker Skoglund - our work on electric armour would not have been such a success without your technical skills, innovative ideas and support. Thank you, Dr. Patrik Lundberg for your support, encouragement and technical expertise. I would like to thank Prof. Nils Brenning and Prof. Anders Larsson, my supervisors at KTH and FOI for their encouragement, support and help in analysing results and writing the papers. Thank you, Dr. Torgny Carlsson, FOI, for encouraging me to begin the PhD-studies, and for your support. A special thanks to you Dr. Bucur Novac, Loughborough University, UK, for your help with the modelling, the analysis of the experiments, and the interpretation of the results from the flux compression generator experiments. Thank you, Dr. Andreas Helte for setting up and performing the hydrodynamic simulations of the explosion process in the flux compression generator, providing valuable input to the electric armour research, and for guiding me into the area of detonics. Dr. Tomas Hurtig and Lars Westerling, it has always been a pleasure to discuss the complex physics observed in the experiments and in the output from your numerical calculations. Other colleagues at FOI that have been supportive and contributed to this work in different ways are Dr. Mose Akyuz, Mattias Elfsberg, Cecilia Möller and Sten Nyholm. My gratitude to the workshop and construction service at FOI Grindsjön for their assistance and help in manufacturing all the necessary auxiliary equipment required when performing these experiments. Finally I would like to thank Anna, my parents Berit and Åke, family and friends for their support, encouragement and patience. viii To Anna and my son Linus x 1 List of papers The work on explosively driven magnetic flux compression generators was thoroughly presented in the licentiate thesis 1. Patrik Appelgren, “Experiments with and modelling of explosively driven magnetic flux compression generators”, Licentiate thesis, TRITA-EE 2008:53, KTH, November 2008 This thesis is based on the work presented in the following journal and conference papers. On explosively driven magnetic flux compression generators: I. P. Appelgren, G. Bjarnholt, N. Brenning, M. Elfsberg, T. Hurtig, A. Larsson, B. M. Novac, and S. E. Nyholm, “Small Helical Magnetic Flux Compression Generators: Experiments and Analysis”, IEEE Transactions on Plasma Science, Vol. 36, No. 5, pp. 2673-2683, October 2008 II. P. Appelgren, N. Brenning, T. Hurtig, A. Larsson, B. M. Novac, and S. E. Nyholm. ”Modeling of a Small Helical Magnetic Flux Compression Generator”, IEEE Transactions on Plasma Science, Vol. 36, No. 5, pp. 2662-2672 , October 2008 III. P. Appelgren, A. Larsson and S. E. Nyholm, “Numerical Simulations of Flux Compression Generator Systems”, proceedings of the 20th IET Pulsed Power Symposium 17-19 September 2007, Oxfordshire, UK pp. 123-127 IV. B.M. Novac, M. Istenič, J. Luo, I.R. Smith, J. Brown, M. Hubbard, P. Appelgren, M. Elfsberg, T. Hurtig, C. Nylander, A. Larsson and S.E. Nyholm, “A 10 GW Pulsed Power Supply for HPM Sources”, IEEE Transactions on Plasma Science, Vol. 34, No. 5, pp. 1814 - 1821 , October 2006 2 On electric armour: V. Patrik Appelgren, Melker Skoglund, Patrik Lundberg, Lars Westerling, Anders Larsson, Tomas Hurtig, “Experimental Study of Electro- magnetic Effects on Solid Copper Jets”, Journal of Applied Mechanics, Vol. 77, No.1, pp. 011010-1 -- 011010-7, January 2010 VI. Patrik Appelgren, Torgny E. Carlsson, Andreas Helte, Tomas Hurtig, Anders Larsson, Patrik Lundberg, Melker Skoglund and Lars Westerling, ”Interaction between Solid Copper Jets and Powerful Electrical Current Pulses”, Journal of Applied Mechanics, Vol.78, No.2, pp. 021006-1 -- 021006-7, March 2011 VII. Patrik Appelgren, Melker Skoglund, Patrik Lundberg, Lars Westerling, Anders Larsson, Tomas Hurtig, ”Disruption Mechanisms in Electrified Solid Copper Jets”, Journal of Applied Mechanics, Vol.78, No.2, pp. 021014-1 -- 021014-5, March 2011 VIII. P. Appelgren, A. Larsson, P. Lundberg, M. Skoglund, L. Westerling, “Studies of Electrically-Exploded Conductors for Electric Armour Applications”, Acta Physica Polonica A, Vol. 115, No. 6, pp. 1072- 1074, 2009 IX. P. Appelgren, L. Westerling, M. Skoglund, P. Lundberg, T. Hurtig, A. Larsson, “Radial Jet Dispersion due to Current Interaction in an Electric Armour Application”, 24th International Symposium on Ballistics, New Orleans, LA, 22-26 September 2008 X. P. Senior, I. R. Smith, P. Appelgren, M. Elfsberg, P. Lundberg, M. Skoglund, “A 400kJ Mobile Pulsed Power System with Variable Pulse Forming”, Proceedings of Megagauss XI, pp 257-261, London, UK, 2006 My contributions to the included publications: Paper I-III: These papers present the experimental work with, and numerical simulations of, explosives driven flux compression generators. The generators were designed and constructed at FOA in 1994-1995. My contribution was to modify, plan and perform the experiments with two remaining generators and to adapt and implement a generator model, developed by Dr. Bucur Novac, into Matlab-Simulink and perform various simulations and parametric studies. I performed the analysis of the experimental data and simulation results and wrote the papers with the support by the co-authors. 3 Paper IV: This paper presents a 10 GW pulsed power supply designed to power a high power microwave (HPM) source. The system was developed by Loughborough University and in order to demonstrate the operation with a microwave source, FOI brought a vircator to Loughborough and mounted the systems together. My contribution was to adapt the FOI vircator to the 10 GW system, participate in the experiments and contribute in writing the paper. Paper V-VII: These papers present the experimental work, results and analysis performed to study the various phenomena occurring when a high velocity metal jet is electrified when passing
Load more

Recommended publications
  • Arxiv:1701.07063V2 [Physics.Ins-Det] 23 Mar 2017 ACCEPTED by IEEE TRANSACTIONS on PLASMA SCIENCE, MARCH 2017 1
    This work has been accepted for publication by IEEE Transactions on Plasma Science. The published version of the paper will be available online at http://ieeexplore.ieee.org. It can be accessed by using the following Digital Object Identifier: 10.1109/TPS.2017.2686648. c 2017 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, including reprinting/republishing this material for advertising or promotional purposes, collecting new collected works for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works. arXiv:1701.07063v2 [physics.ins-det] 23 Mar 2017 ACCEPTED BY IEEE TRANSACTIONS ON PLASMA SCIENCE, MARCH 2017 1 Review of Inductive Pulsed Power Generators for Railguns Oliver Liebfried Abstract—This literature review addresses inductive pulsed the inductor. Therefore, a coil can be regarded as a pressure power generators and their major components. Different induc- vessel with the magnetic field B as a pressurized medium. tive storage designs like solenoids, toroids and force-balanced The corresponding pressure p is related by p = 1 B2 to the coils are briefly presented and their advantages and disadvan- 2µ tages are mentioned. Special emphasis is given to inductive circuit magnetic field B with the permeability µ. The energy density topologies which have been investigated in railgun research such of the inductor is directly linked to the magnetic field and as the XRAM, meat grinder or pulse transformer topologies. One therefore, its maximum depends on the tensile strength of the section deals with opening switches as they are indispensable for windings and the mechanical support.
    [Show full text]
  • Pulsed Power Pulsed Power
    PULSED POWER PULSED POWER Gennady A. Mesyats Institute of High Current Electronics, Tomsk, and Institute of Electrophysics, Ekaterinburg Russian Academy of Sciences, Russia Springe r Library of Congress Cataloging-in-Publication Data Mesiats, G. A. (Gennadii Andreevich) Pulsed power/by Gennady A. Mesyats. p. cm. Includes bibliographical references and index. ISBN 0-306-48653-9 (hardback) - ISBN 0-306-48654-7 (eBook) 1. Pulsed power systems. I. Title. TK2986.M47 2004 621.381534—dc22 2004051665 ISBN: 0-306-48653-9 (hardback) ISBN: 0-306-48654-7 (eBook) Printed on acid-free paper. © 2005 Springer Science+Business Media, Inc. All rights reserved. This work may not be translated or copied in whole or in part without the written permission of the publisher (Springer Science+Business Media, Inc., 233 Spring Street, New York, NY 10013, USA), except for brief excerpts in connection with reviews or scholarly analysis. Use in connection with any form of information storage and retrieval, electronic adap­ tation, computer software, or by similar or dissimilar methodology now known or hereafter developed is forbidden. The use in this publication of trade names, trademarks, service marks and similar terms, even if they are not identified as such, is not to be taken as an expression of opinion as to whether or not they are subject to proprietary rights. Printed in the United States of America. (SPI) 10 98765432 springer.com Contents Preface xiii PART 1. PULSED SYSTEMS: DESIGN PRINCIPLES 1 Chapter 1. LUMPED PARAMETER PULSE SYSTEMS 3 1. Principal schemes for pulse generation 3 2. Voltage multiplication and transformation 6 References 12 Chapter 2.
    [Show full text]
  • Pulsed Power Engineering Switching Devices
    Pulsed Power Engineering Switching Devices January 12-16, 2009 Craig Burkhart, PhD Power Conversion Department SLAC National Accelerator Laboratory Ideal Switch •V = ∞ •I = ∞ • Closing/opening time = 0 • L = C = R = 0 • Simple to control • No delay or jitter •Lasts forever • Never fails January 12-16, 2009 USPAS Pulsed Power Engineering C Burkhart 2 Switches • Electromechanical • Vacuum •Gas – Spark gap – Thyratron – Ignitron – Plasma Opening • Solid state – Diodes • Diode opening switch – Thyrsitors • Electrically triggered • Optically triggered • dV/dt triggered – Transistors •IGBT • MOSFET January 12-16, 2009 USPAS Pulsed Power Engineering C Burkhart 3 Switches • Electromechanical – Open relay • To very high voltages, set by size of device • Commercial devices to ~0.5 MV, ~50 kA – Ross Engineering Corp. • Closing time ~10’s of ms typical – Large jitter, ~ms typical • Closure usually completed by arcing – Poor opening switch • Commonly used as engineered ground – Vacuum relay • Models that can open under load are available • Commercial devices – Maximum voltage ~0.1 MV – Maximum current ~0.1 kA – Tyco-kilovac –Gigavac January 12-16, 2009 USPAS Pulsed Power Engineering C Burkhart 4 Gas/Vacuum Switch Performance vs. Pressure January 12-16, 2009 USPAS Pulsed Power Engineering E Cook 5 Vacuum Tube (Switch Tube) • Space-charge limited current flow 1.5 –VON α V – High power tubes have high dissipation • Similar opening/closing characteristics • Maximum voltage ~0.15 MV • Maximum current ~0.5 kA, more typically << 100 A • HV grid drive • Decreasing availability • High Cost January 12-16, 2009 USPAS Pulsed Power Engineering C Burkhart 6 Spark Gaps • Closing switch • Generally inexpensive - in simplest form: two electrodes with a gap • Can operated from vacuum to high pressure (both sides of Paschen Curve) • Can use almost any gas or gas mixture as a dielectric.
    [Show full text]
  • What Is Pulsed Power
    SAND2007-2984P PULSED POWER AT SANDIA NATIONAL LABORATORIES LABORATORIES NATIONAL SANDIA PULSED POWER AT WHAT IS PULSED POWER . the first forty years In the early days, this technology was often called ‘pulse power’ instead of pulsed power. In a pulsed power machine, low-power electrical energy from a wall plug is stored in a bank of capacitors and leaves them as a compressed pulse of power. The duration of the pulse is increasingly shortened until it is only billionths of a second long. With each shortening of the pulse, the power increases. The final result is a very short pulse with enormous power, whose energy can be released in several ways. The original intent of this technology was to use the pulse to simulate the bursts of radiation from exploding nuclear weapons. Anne Van Arsdall Anne Van Pulsed Power Timeline (over) Anne Van Arsdall SAND2007-????? ACKNOWLEDGMENTS Jeff Quintenz initiated this history project while serving as director of the Pulsed Power Sciences Center. Keith Matzen, who took over the Center in 2005, continued funding and support for the project. The author is grateful to the following people for their assistance with this history: Staff in the Sandia History Project and Records Management Department, in particular Myra O’Canna, Rebecca Ullrich, and Laura Martinez. Also Ramona Abeyta, Shirley Aleman, Anna Nusbaum, Michael Ann Sullivan, and Peggy Warner. For her careful review of technical content and helpful suggestions: Mary Ann Sweeney. For their insightful reviews and comments: Everet Beckner, Don Cook, Mike Cuneo, Tom Martin, Al Narath, Ken Prestwich, Jeff Quintenz, Marshall Sluyter, Ian Smith, Pace VanDevender, and Gerry Yonas.
    [Show full text]
  • Pulsed Power Generator Using Solid-State LTD Modules
    Pulsed Power Generator Using Solid-State LTD Modules Weihua Jiang and Akira Tokuchi Extreme Energy-Density Research Institute, Nagaoka University of Technology, Nagaoka, Japan ABSTRACT Linear transformer driver (LTD) modules using power MOSFETs as switches have been developed and tested for applications to repetitive, compact pulsed power sources. It is based on the same principle as large-scale LTDs being developed abroad for fusion and high energy-density physics purposes, while having advantages in high repetition rate and turning-off capability. It is expected to become a new approach leading to innovative compact pulsed power generators. Keywords Pulsed power, power electronics, high voltage, LTD, MOSFET 1. Introduction solid-state LTD technology is being developed for Linear transformer driver (LTD) technology is industrial applications.4) being developed for large-scale pulsed power facilities aiming at nuclear fusion and high 2. Experimental Setup energy-density physics applications.1-3) In the LTD Figure 1 shows the LTD module using MOSFETs scheme, the pulsed power is generated by a large as switches. It has 35 basic circuits each of which number of synchronized basic circuits, each consists consists of a capacitor, a MOSFET, and driver IC. of a capacitor (or capacitors) and a switch. The These basic circuits are connected in parallel. required output power and output impedance of a There is an optical module which converts the optical system is obtained by connecting these basic circuits control signal to electrical signal and sends it to the in parallel (for the current) and by adding their output driver ICs. The major circuit elements are shown in inductively (for the voltage).
    [Show full text]
  • Modular Marx Generator Based on Sic-MOSFET Generating Adjustable Rectangular Pulses
    energies Article Modular Marx Generator Based on SiC-MOSFET Generating Adjustable Rectangular Pulses Yahia Achour 1,*,† , Jacek Starzy ´nski 2,† and Jacek R ˛abkowski 2,† 1 Ecole Militaire Polytechnique, Algiers 16111, Algeria 2 Faculty of Electrical Engineering, Warsaw University of Technology, Koszykowa 75, 00-662 Warszawa, Poland; [email protected] (J.S.); [email protected] (J.R.) * Correspondence: [email protected] † These authors contributed equally to this work. Abstract: The paper introduces a new design of Marx generator based on modular stages using Silicon Carbide MOSFETs (SiC-MOSFET) aimed to be used in biomedical applications. In this process, living cells are treated with intense nanosecond Pulsed Electrical Field (nsPEF). The electric field dose should be controlled by adjusting the pulse parameters such as amplitude, repetition rate and pulse-width. For this purpose, the structure of the proposed generator enables negative pulses with a quasi-rectangular shape, controllable amplitude, pulse-width and repetition-rate. A complete simulation study was conducted in ANSYS-Simplorer to verify the overall performance. A compact, modular prototype of Marx generator was designed with 1.7 kV rated SiC-MOSFETs and, finally, a set of experiments confirmed all expected features. Keywords: Marx generator; SiC-MOSFET; solid-state; pulsed power Citation: Achour, Y.; Starzy´nski,J.; R ˛abkowski,J. Modular Marx 1. Introduction Generator Based on SiC-MOSFET The rapidly increasing share of semiconductor switches in electrical engineering is Generating Adjustable Rectangular due to their high performances in terms of controllability, compactness and lifetime. This Pulses. Energies 2021, 14, 3492. can be seen in many domains such as power electronics, motor drivers and many other https://doi.org/10.3390/en14123492 areas, including pulsed power.
    [Show full text]
  • Pulsed Power Engineering Basic Topologies
    Pulsed Power Engineering Basic Topologies January 12-16, 2009 Craig Burkhart, PhD Power Conversion Department SLAC National Accelerator Laboratory Basic Topologies • Basic circuits • Hard tube •Line-type – Transmission line – Blumlein – Pulse forming network • Charging circuits • Controls January 12-16, 2009 USPAS Pulsed Power Engineering C Burkhart 2 Basic Circuits: RC • Capacitor charge • Capacitor discharge • Passive integration – low-pass filter – τ << RC: integrates signal, VOUT = (1/RC) ∫ VIN dt – τ >> RC: low pass, VOUT = VIN • Passive differentiation – high-pass filter – τ >> RC: differentiates signal, VOUT = (RC) dVIN /dt – τ << RC: high pass, VOUT = VIN • Resistive charging of capacitors January 12-16, 2009 USPAS Pulsed Power Engineering C Burkhart 3 RC Charge January 12-16, 2009 USPAS Pulsed Power Engineering TTU-PPSC 4 RC Discharge January 12-16, 2009 USPAS Pulsed Power Engineering TTU-PPSC 5 Resistive Charging of a Capacitor It is resistive charging if charging current, IC= ΔVR/R, through full charging cycle January 12-16, 2009 USPAS Pulsed Power Engineering TTU/Burkhart 6 Resistive Charging of a Capacitor In resistive charging a minimum of 50% of the energy is dissipated in the charging resistor January 12-16, 2009 USPAS Pulsed Power Engineering TTU/Burkhart 7 LR Circuit: Inductive Risetime Limit • At t=0, close switch and apply V=1 to LR circuit • Inductance limits dI/dt • Reach 90% of equilibrium current, V/R, in ~2.2 L/R January 12-16, 2009 USPAS Pulsed Power Engineering C Burkhart 8 LR Circuit: Decay of Inductive Current
    [Show full text]
  • DIAGNOSTICS SYSTEM for the 67MJ, 50Kv PULSE POWER CAPACITOR BANK
    CZ9726881 DIAGNOSTICS SYSTEM FOR THE 67MJ, 50kV PULSE POWER CAPACITOR BANK I.V.Galakhov, A.S.Gasheyev, I.A Gruzin., S.N.Gudov, V.M.Murugov, V.A.Osin, V.I.Pankratov, I.N.Pegoev RFNC-VNIIEF, Sarov (Arzamas-16), Russsia Abstract The diagnostics system described in the paper is for charging and discharging to the load of the large 67MJ and 50kV capacitor bank for the iodine laser pulse power of ISKRA-5 facility. Discharging diagnostics of the capacitor bank has used a technique to measure a sequence of times between representative discharge events for 665 discharge circuits of the bank. Benefits of the measurement techniques used are discussed. Introduction High-power laser facilities have been built in many countries for experimental research in laser fusion area. Among its subsystems every such facility has a pulse power system to supply flashlamps in the active medium pumping system of laser amplifiers. The pulse power system is built upon capacitor banks which are separated into individual modules. Each module is a bunch of capacitors which is discharged through a switched of the flashlamp an individual load. High-power operating currents (Imax<300kA) and voltage (Uch^50kV) are what predetermine failure probability for high-voltage components as PfajnlO^-lO^per shot with 4 the total number of component Nc>10 . There fore, in each physics experiments there may be any kind of failure in the pulse power system, which has to be detected and eliminated. This is what the capacitor bank diagnostics system is intended for. There are some considerations that make the diagnostics system development a difficult problem.
    [Show full text]
  • Pulsed Fission – Fusion (Puff) Phase 1 Report
    Pulsed Fission-Fusion (PuFF) – Phase I Report Robert B. Adams, Ph.D. National Aeronautics and Space Administration George C. Marshall Space Flight Center Jason Cassibry, Ph.D. University of Alabama in Huntsville Propulsion Research Center David E. Bradley Yetispace, Inc. Leo Fabisinski International Space Systems, Inc. Geoffrey Statham, D.Phil. ERC, Inc. Executive Summary In September 2013 the NASA Innovative Advanced Concept (NIAC) organization awarded a phase I contract to the PuFF team. Our phase 1 proposal discussed a pulsed fission-fusion propulsion system that injected gaseous deuterium (D) and tritium (T) as a mixture in a column, surrounded concentrically by gaseous uranium fluoride (UF6) and then an outer shell of liquid lithium. A high power current would flow down the liquid lithium and the resulting Lorentz force would compress the column by roughly a factor of 10. The compressed column would reach criticality and a combination of fission and fusion reactions would occur. The fission reactions would further energize the fusion center, and the fusion reactions would generate neutrons that promote more complete burnup of the fission fuel. The lithium liner provides some help as a neutron reflector but also acts as a propulsive medium, being converted to plasma which is then expanded against a magnetic nozzle for thrust. The expansion of the (primarily) lithium plasma against the nozzle’s magnetic field inducts a current that is used to charge the system for the next pulse. Our concept also included secondary injection of a Field Reversed Configuration (FRC) plasmoid that would provide a secondary compression direction, axially against the column, and push the column away from the injection manifold, increasing the manifold’s survivability.
    [Show full text]
  • Review of Solid-State Modulators
    REVIEW OF SOLID-STATE MODULATORS E. G. Cook, Lawrence Livermore National Laboratory, USA Abstract closing switches. The semiconductor industry’s continued development of devices for traction applications and high Solid-state modulators for pulsed power applications frequency switching power supplies have created entire have been a goal since the first fast high-power families of devices that have a unique combination of semiconductor devices became available. Recent switching capabilities. For the first time we are seeing improvements in both the speed and peak power production quantities of devices that may be considered to capabilities of semiconductor devices developed for the be close to "ideal switches". These ideal switches are power conditioning and traction industries have led to a devices that have a fast turn-off capability as well as fast new generation of solid-state switched high power turn-on characteristics; devices that have minimal trigger modulators with performance rivaling that of hard tube power requirements and are capable of efficiently modulators and thyratron switched line-type modulators. switching large amounts of energy in very short periods These new solid-state devices offer the promise of higher of time and at high repetition rates if so required. efficiency and longer lifetimes at a time when availability There are two devices that come close to meeting these of standard technologies is becoming questionable. criteria for ideal switches, Metal Oxide Semiconductor A brief discussion of circuit topologies and solid-state Field Effect Transistors (MOSFETs) and Insulated Gate devices is followed by examples of modulators currently Bipolar Transistors (IGBTs). These devices and in use or in test.
    [Show full text]
  • Gas-Discharge Closing Switches and Their Time Jitter Anders Larsson, Senior Member, IEEE
    IEEE TRANSACTIONS ON PLASMA SCIENCE, VOL. 40, NO. 10, OCTOBER 2012 2431 Gas-Discharge Closing Switches and Their Time Jitter Anders Larsson, Senior Member, IEEE Abstract—Gas-discharge closing switches are still the main op- tion for pulsed-power systems where high hold-off voltage and high-power handling capabilities are required. One property of the switch that often is of great importance is the precision in time when the switch is to be closed. This review is a survey of existing gas-discharge closing switches, and in particular of their switching time jitter. Index Terms—Gas-discharge devices, pulse power system switches, reviews, time jitter. I. INTRODUCTION Fig. 1. Different phases that build up the delay time in a triggered gas- IGH-VOLTAGE CLOSING switches in pulsed-power discharge switch. All of these phases may introduce a time jitter. systems are often subjected to the toughest requirements H II. TIME JITTER IN PULSED-POWER SYSTEMS of all components in the system and a multitude of properties must be considered [1], [2]. Timing precision in the closure Jitter is present in every pulsed-power system, that is, a of the switches is vital if the system contains several sources variation of output parameters even if the initial and control- that need to be switched in a synchronized manner either into lable settings are the same [5]. In particular, closing switches a single load or into separate loads. This review is based on introduce such jitter, and all the different phases of the closing a literature survey of how precisely one can trigger externally of the switch may contribute to this jitter.
    [Show full text]
  • A Tesla-Blumlein PFL-Bipolar Pulsed Power Generator Laurent Pecastaing, Meng Wang
    A Tesla-Blumlein PFL-Bipolar Pulsed Power Generator Laurent Pecastaing, Meng Wang To cite this version: Laurent Pecastaing, Meng Wang. A Tesla-Blumlein PFL-Bipolar Pulsed Power Generator. Electro- magnetism. Loughborough University, 2016. English. tel-02372305 HAL Id: tel-02372305 https://hal-univ-pau.archives-ouvertes.fr/tel-02372305 Submitted on 20 Nov 2019 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. Meng Wang A Tesla-Blumlein PFL-Bipolar Pulsed Power Generator by Meng Wang, MSc, BEng A Doctoral Thesis submitted in partial fulfilment of the requirements for the award of Doctor of Philosophy of Loughborough University, UK March 2016 © Meng Wang, 2016 Meng Wang Acknowledgements I would like to express my sincere gratitude and to acknowledge the assistance and continuous support received from my supervisor Professor Bucur Novac, who was a constant source of inspiration and expert advice during my research work. I am very fortunate to have been associated with him. Special thanks are also due to thank Professor Ivor Smith for his efforts and I am also grateful to him for his reviews and advice throughout the writing of the thesis. I am very grateful to Mr.
    [Show full text]