STANDARD SAIL and EQUIPMENT SPECIFICATIONS (Updated October, 2016)
Total Page:16
File Type:pdf, Size:1020Kb
Load more
Recommended publications
-
Armed Sloop Welcome Crew Training Manual
HMAS WELCOME ARMED SLOOP WELCOME CREW TRAINING MANUAL Discovery Center ~ Great Lakes 13268 S. West Bayshore Drive Traverse City, Michigan 49684 231-946-2647 [email protected] (c) Maritime Heritage Alliance 2011 1 1770's WELCOME History of the 1770's British Armed Sloop, WELCOME About mid 1700’s John Askin came over from Ireland to fight for the British in the American Colonies during the French and Indian War (in Europe known as the Seven Years War). When the war ended he had an opportunity to go back to Ireland, but stayed here and set up his own business. He and a partner formed a trading company that eventually went bankrupt and Askin spent over 10 years paying off his debt. He then formed a new company called the Southwest Fur Trading Company; his territory was from Montreal on the east to Minnesota on the west including all of the Northern Great Lakes. He had three boats built: Welcome, Felicity and Archange. Welcome is believed to be the first vessel he had constructed for his fur trade. Felicity and Archange were named after his daughter and wife. The origin of Welcome’s name is not known. He had two wives, a European wife in Detroit and an Indian wife up in the Straits. His wife in Detroit knew about the Indian wife and had accepted this and in turn she also made sure that all the children of his Indian wife received schooling. Felicity married a man by the name of Brush (Brush Street in Detroit is named after him). -
Mainsail Trim Pointers, Reefing and Sail Care for the Beneteau Oceanis Series
Neil Pryde Sails International 1681 Barnum Avenue Stratford, CT 06614 203-375-2626 [email protected] INTERNATIONAL DESIGN AND TECHNICAL OFFICE Mainsail Trim Pointers, Reefing and Sail Care for the Beneteau Oceanis Series The following points on mainsail trim apply both to the Furling and Classic mainsails we produce for Beneteau USA and the Oceanis Line of boats. In sailing the boats we can offer these general ideas and observations that will apply to the 311’s through to the newest B49. Mainsail trim falls into two categories, upwind and downwind. MAINSAIL TRIM: The following points on mainsail trim apply both to the Furling and Classic mainsail, as the concepts are the same. Mainsail trim falls into two categories, upwind and downwind. Upwind 1. Upwind in up to about 8 knots true wind the traveler can be brought to weather of centerline. This ensures that the boom will be close centerline and the leech of the sail in a powerful upwind mode. 2. The outhaul should be eased 2” / 50mm at the stopper, easing the foot of the mainsail away from the boom about 8”/200mm 3. Mainsheet tension should be tight enough to have the uppermost tell tail on the leech streaming aft about 50% of the time in the 7- 12 true wind range. For those with furling mainsails the action of furling and unfurling the sail can play havoc with keeping the telltales on the sail and you may need to replace them from time to time. Mainsail outhaul eased for light air upwind trim You will find that the upper tell tail will stall and fold over to the weather side of the sail about 50% of the time in 7-12 knots. -
Spinnakers and Poles/Bowsprits Explained
SPINNAKERS AND POLES/BOWSPRITS EXPLAINED The RORC Rating Office is sometimes asked whether symmetric and asymmetric spinnakers are rated differently, and whether there is a rating increase if you use both types. The question is often prompted by the IRC application form asking questions about the spinnakers of each type carried aboard, rather than just the largest spinnaker area (SPA) and total number of spinnakers. There are two aspects of downwind sail rating: the sail itself and the type of pole (if any) it is set on - as explained below. Text in italics is taken from the IRC 2018 Rule text. SPINNAKERS For the calculation of your rating, IRC considers the largest spinnaker area (SPA) and the total number of spinnakers carried. 21.6 Spinnakers 21.6.1 Boats carrying more than three spinnakers in total on board while racing will incur an increase in rating. 21.6.2 Spinnaker area (SPA) shall be calculated from: SPA = ((SLU + SLE)/2) * ((SFL + (4 * SHW))/5) * 0.83 SLU, SLE, SFL and SHW of the largest area spinnaker on board shall be declared. The calculated area of this spinnaker will be shown on a boat’s certificate as the maximum permitted SPA. 8.10.1 Values stated on certificates for LH, Hull Beam, Bulb Weight, Draft, x, P, E, J, FL, MUW, MTW, MHW, HLUmax, HSA, PY, EY, LLY, LPY, Cutter Rig HLUmax, SPA, STL are maximum values. Are symmetric or asymmetric spinnakers rated differently? Not directly, but see the section on pole type below. Is there a rating increase if I carry both symmetric and asymmetric spinnakers? Not directly, but see the section on pole type below. -
The New York Sloop
The New York Sloop The most important of the sloop-rigged small-boat types used in the fisheries was the New York sloop, which had a style of hull and rig that influenced the design of both yachts and work-boats for over thirty years. The New York boats were developed sometime in the 1830's, when the centerboard had been accepted. The boats were built all about New York Bay, particularly on the Jersey shore. The model spread rapidly, and, by the end of the Civil War, the shoal centerboard sloop of the New York style had appeared all along the shores of western Long Island Sound, in northern New Jersey, and from thence southward into Delaware and Chesapeake waters. In the postwar growth of the southern fisheries, during the 1870's and 80's, this class of sloop was adopted all along the coasts of the South Atlantic states and in the Gulf of Mexico; finally, the boats appeared at San Francisco. The model did not become very popular, however, east of Cape Cod. The New York sloop was a distinctive boat—a wide, shoal centerboarder with a rather wide, square stern and a good deal of dead rise, the midsection being a wide, shallow V with a high bilge. The working sloops usually had a rather hard bilge; but in some it was very slack, and a strongly flaring side was used. Originally, the ends were plumb, and the stem often showed a slight tumble home at the cutwater. V-sterns and short overhanging counters were gradually introduced in the 1850's, particularly in the boats over 25 feet in length on deck. -
Designing Sails Since 1969
SAILRITE SAIL KITS Designing sails since 1969. Catalina 30 Tall Rig Mainsail Kit by Frederick Leroy Carter F 31R Screecher Kit by Patrick Pettengill Capri 18 Main & Jib Sail Kits by Brent Stiles “ We built this sail ourselves!” Custom Lateen Main Kit by Steve Daigle -Karen Larson Building your own sail is a very rewarding and satisfying Each kit comes with the sail design data and a set of instructions experience. Not only is there a real sense of accomplishment, and illustrations that have been perfected from over 40 years of but the skills developed in the process will make you a more self- experience and feedback. Sail panels are pre-cut, labeled and reliant sailor. Sailrite makes the process very easy and affordable numbered for easy assembly. Panel overlap and hemming lines from start to finish by providing sail kits that include materials come plotted on each panel and double-sided tape is included used by professional sailmakers at up to 50% less the cost! to adhere panels together prior to sewing to ensure that draft and shape are maintained during construction. Batten pockets, Sailrite uses state-of-the-art design programs and hardware to windows, draft stripes, reef points, and other details will also prepare each kit. Sail panels and corner reinforcements are all come plotted on the appropriate panels if required for your sail. computer-cut and seaming lines are drawn along the edges. Draft, twist, and entry and exit curves are all carefully calculated, controlled, and positioned for each sail to maximize performance. Getting Started All materials are carefully selected by our sail designers to Getting started is easy and Sailrite’s expert staff is available toll best suit your application and only high quality sailcloths and free every working day to answer questions and help guide you laminates from Bainbridge, Challenge, Contender and others who through the ordering and construction process. -
Additional Specs, Equipment and Information
http://sailnorthwest.com Bob Ross Toll-free 877-213-7441 7001 Seaview Ave NW, ste 140 Tel 206 286 1004 Tel 206 286 1004 Seattle, WA 98117 United States Fax 206 286 1353 Email [email protected] 29' C&C 29 Year: 1983 Last Listed Price: US$ 19,900 (12/14) Sold: US$ 17,750 (01/15) Located in Seattle, WA Hull Material: Fiberglass Engine/Fuel Type: Single diesel YW# 22784-2793845 Sold Antsea Quality, clean, reliable and fun C&C. Renowned for being well built and a great performer, the C&C 29 Mk2 is a great boat for Pacific Northwest PHRF racing, day sailing, fishing and weekend or extended cruising for families. She moves well in light air, cruises at 6 knots, is lively and fun to sail and is able to explore most anywhere with her 4' 3" shoal draft keel. She is ready for your next journey. Additional Specs, Equipment and Information: Dimensions LOA: 28.42 feet LWL: 24.75 feet Beam: 9.42 feet Displacement: 6700 pound Ballast: 2700 pound Cruising Speed: 6 knots Max Speed: 6.5 knots General Description On deck a large cockpit and wheel steering provides ample room for crew and fold out table for eating outside on warm days, but protected with a dodger when the weather turns, which can also fold down for racing. All lines lead back to the cockpit, which is great for single-handing. At 29 feet she is also very easy to maneuver in the marina. Under power, a super reliable fresh water-cooled Yanmar Diesel moves her easily through the water. -
Are We Having Fun Yet! Created by John Barnett
Are we having fun Yet! created by John Barnett { Rule 1, Never go down below specially with the engine running packing food, that should have been done at the dock. If you feel it coming on, do something active like steering. If you are prone to sea sickness take the proper drugs, before leaving the dock, better at night before to start. If sick, keep warm, try to drink, stay on deck, small bucket can be your friend. I have small buckets on my boat. No Cotton underwear will keep you cold. No! you can’t swim with the dolphins. Follow what the doc told you today. If wind is coming in the Galveston channel and against the current. Leave the channel going close to the east jetty, sail out until the waves calm down, then turn to the start. This can be the worst part of the race. Seasickness is the major problem! Understand the clouds and winds Watch the barometer, if it starts dropping shorten sail. If you smell ozone that fresh lighting smell, all hell is about to happen sails should have been reefed. Which way is the wind blowing? If the wind is blowing from the aft and the big clouds are coming from forward. Shorten sail. Make sure someone go down close and lock everything early. Fronts: Time to change sails or prepare for a wind shift. Do you have your harness on with life jacket? Jib should be rolled up, main ready to be reefed or done, look at the waves up there for a shift looking at white caps, flying spray starts at 27kts in salt water Shortening Sails First of all, does everyone in the crew know how? Skipper maybe sea sick down below. -
Sailing Course Materials Overview
SAILING COURSE MATERIALS OVERVIEW INTRODUCTION The NCSC has an unusual ownership arrangement -- almost unique in the USA. You sail a boat jointly owned by all members of the club. The club thus has an interest in how you sail. We don't want you to crack up our boats. The club is also concerned about your safety. We have a good reputation as competent, safe sailors. We don't want you to spoil that record. Before we started this training course we had many incidents. Some examples: Ran aground in New Jersey. Stuck in the mud. Another grounding; broke the tiller. Two boats collided under the bridge. One demasted. Boats often stalled in foul current, and had to be towed in. Since we started the course the number of incidents has been significantly reduced. SAILING COURSE ARRANGEMENT This is only an elementary course in sailing. There is much to learn. We give you enough so that you can sail safely near New Castle. Sailing instruction is also provided during the sailing season on Saturdays and Sundays without appointment and in the week by appointment. This instruction is done by skippers who have agreed to be available at these times to instruct any unkeyed member who desires instruction. CHECK-OUT PROCEDURE When you "check-out" we give you a key to the sail house, and you are then free to sail at any time. No reservation is needed. But you must know how to sail before you get that key. We start with a written examination, open book, that you take at home. -
Sunfish Sailboat Rigging Instructions
Sunfish Sailboat Rigging Instructions Serb and equitable Bryn always vamp pragmatically and cop his archlute. Ripened Owen shuttling disorderly. Phil is enormously pubic after barbaric Dale hocks his cordwains rapturously. 2014 Sunfish Retail Price List Sunfish Sail 33500 Bag of 30 Sail Clips 2000 Halyard 4100 Daggerboard 24000. The tomb of Hull Speed How to card the Sailing Speed Limit. 3 Parts kit which includes Sail rings 2 Buruti hooks Baiky Shook Knots Mainshoat. SUNFISH & SAILING. Small traveller block and exerts less damage to be able to set pump jack poles is too big block near land or. A jibe can be dangerous in a fore-and-aft rigged boat then the sails are always completely filled by wind pool the maneuver. As nouns the difference between downhaul and cunningham is that downhaul is nautical any rope used to haul down to sail or spar while cunningham is nautical a downhaul located at horse tack with a sail used for tightening the luff. Aca saIl American Canoe Association. Post replys if not be rigged first to create a couple of these instructions before making the hole on the boom; illegal equipment or. They make mainsail handling safer by allowing you relief raise his lower a sail with. Rigging Manual Dinghy Sailing at sailboatscouk. Get rigged sunfish rigging instructions, rigs generally do not covered under very high wind conditions require a suggested to optimize sail tie off white cleat that. Sunfish Sailboat Rigging Diagram elevation hull and rigging. The sailboat rigspecs here are attached. 650 views Quick instructions for raising your Sunfish sail and female the. -
“F-27 1996 Sail Plan ”-Layer#1
Sail Luff Leach Foot Material Area RECOMMENDED 50mm MAINSAIL CAMBER: 100/4" 2" Mainsail 33' 4" 35' 1" 12' 10" Mylar 317sq.ft. Top Third 10% at 44% aft Cutout for Middle 12% at 48% aft halyard Jib 33' 9" 30' 2" 11' 7" Mylar 185sq.ft. Bottom Third 6% at 46% aft clearance Recommended mast pre-bend is 3" Genoa 33' 9" 30' 8" 16' 1" Mylar 272sq.ft. Maximum headstay tension is 2700lbs, HEAD 9mm Rope Luff sag is 4-5" DETAIL Asy. Spinn. 39' 8" 36' 26' 11" Nylon 772sq.ft. 3/8" min. gap for Screacher 34' 10' 31' 9" 21' Mylar 343sq.ft. feeder clearance 31" Storm Jib 17' 12' 11" 9' 11" Mylar 59sq.ft. Batten Plastic Batten pocket end plate, bolted R. Furling 31' 9" 29' 11" 15' 8" Mylar 231sq.ft. Genoa or riveted through sail 1996 F-27 ® Class Rules: Mainsail BATTEN END DETAIL Max. Main Head Width (MHW) = 31" Maximum P (Luff) = 33' 4" Maximum E (Foot) = 12' 10" Maximum 1/4 P girth = 7' 4" 8oz Teflon Maximum 1/2 P girth = 10' 3" tape The mainsail shall be attached to the mast with a bolt rope and/or slugs. The mainsail shall be roller reefing and 9mm hard furling. 3/4" 12" 16" ® braided rope 9 1/4" Headsails (Jib & Genoa) MAIN LUFF TAPE: to be 8oz Number of headsails carried within these 25" measurements is left to the owners Teflon Tape or similar over 9mm discretion. 3"27 solid braided rope Maximum Luff = 33' 9" MAIN FOOT TAPE: to be 8oz Maximum Luff Perp. -
Further Devels'nent Ofthe Tunny
FURTHERDEVELS'NENT OF THETUNNY RIG E M H GIFFORDANO C PALNER Gi f ford and P art ners Carlton House Rlngwood Road Hoodl ands SouthamPton S04 2HT UK 360 1, lNTRODUCTION The idea of using a wing sail is not new, indeed the ancient junk rig is essentially a flat plate wing sail. The two essential characteristics are that the sail is stiffened so that ft does not flap in the wind and attached to the mast in an aerodynamically balanced way. These two features give several important advantages over so called 'soft sails' and have resulted in the junk rig being very successful on traditional craft. and modern short handed-cruising yachts. Unfortunately the standard junk rig is not every efficient in an aer odynamic sense, due to the presence of the mast beside the sai 1 and the flat shapewhich results from the numerousstiffening battens. The first of these problems can be overcomeby usi ng a double ski nned sail; effectively two junk sails, one on either side of the mast. This shields the mast from the airflow and improves efficiency, but it still leaves the problem of a flat sail. To obtain the maximumdrive from a sail it must be curved or cambered!, an effect which can produce over 5 more force than from a flat shape. Whilst the per'formanceadvantages of a cambered shape are obvious, the practical way of achieving it are far more elusive. One line of approach is to build the sail from ri gid componentswith articulated joints that allow the camberto be varied Ref 1!. -
Setting, Dousing and Furling Sails the Perception of Risk Is Very Important, Even Essential, to Organization the Sense of Adventure and the Success of Our Program
Setting, Dousing and Furling Sails The perception of risk is very important, even essential, to Organization the sense of adventure and the success of our program. The When at sea the organization for setting and assurance of safety is essential dousing sails will be determined by the Captain to the survival of our program and the First Mate. With a large and well- and organization. The trained crew, the crew may be able to be broken balancing of these seemingly into two groups, one for the foremast and one conflicting needs is one of the for the mainmast. With small crews, it will most difficult and demanding become necessary for everyone to know and tasks you will have in working work all of the lines anywhere on the ship. In with this program. any event, particularly if watches are being set, it becomes imperative that everyone have a good understanding of all lines and maneuvers the ship may be asked to perform. Safety Sailing the brigantines safely is our primary goal and the Los Angeles Maritime Institute has an enviable safety record. We should stress, however, that these ships are NOT rides at Disneyland. These are large and powerful sailing vessels and you can be injured, or even killed, if proper procedures are not followed in a safe, orderly, and controlled fashion. As a crewmember you have as much responsibility for the safe running of these vessels as any member of the crew, including the ship’s officers. 1. When laying aloft, crewmembers should always climb and descend on the weather side of the shrouds and the bowsprit.