DOCSLIB.ORG

Inverness Yacht Club Adult Sailing Checkout Program Club Laser Rigging Instructions

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Inverness Yacht Club Adult Sailing Checkout Program Club Laser Rigging Instructions Inverness Yacht Club Adult Sailing Checkout Program Club Laser Rigging Instructions Ned Congdon July 8, 2020 7/8/2020 Inverness YC Laser Rigging Instructions 1 Make sure the drain flap is retracted. Otherwise it will break when you slide it down the ramp. The boat should look like this to start IMG_2153 with IMG_2144 These are the two mast sections. The various Jiggle the plug to retract the drain flap lines should be wrapped around the lower IMG_2152 mast section , ideally neater than this, but this 7/8/2020 Inverness YC Laser Rigging Instructions is acceptable. IMG_2159 2 Assemble mast sections together IMG_2154 Arrow on top portion should be pointing to the rivet on the bottom portion IMG_2156 Slide sail over mast and put mast in step while boat is on the dock IMG_2180 Mainsheet rigged and ready to go IMG_2183 7/8/2020 Inverness YC Laser Rigging Instructions 3 Vang, Cunningham and Outhaul 7/8/2020 Inverness YC Laser Rigging Instructions 4 Vang, Outhaul and Cunningham before rigging IMG_2183 7/8/2020 Inverness YC Laser Rigging Instructions 5 Separate Vang from Outhaul from Cunningham. Greg is holding the Cunningham. IMG_2184 7/8/2020 Inverness YC Laser Rigging Instructions 6 Greg is holding the mast portion of the Outhaul IMG_2189 7/8/2020 Inverness YC Laser Rigging Instructions 7 Where Greg is holding the Outhaul, is where the mast portion of the Outhaul will later be joined with the boom portion IMG_2190 7/8/2020 Inverness YC Laser Rigging Instructions 8 Continue to separate Vang from Outhaul from Cunningham. Greg is holding the Vang in his left hand and the Cunningham in his right. IMG_2187 7/8/2020 Inverness YC Laser Rigging Instructions 9 Boom installed on gooseneck. Greg is holding the Vang. IMG_2195 7/8/2020 Inverness YC Laser Rigging Instructions 10 Another view of previous IMG_2196 7/8/2020 Inverness YC Laser Rigging Instructions 11 Vang attached to boom IMG_2197 7/8/2020 Inverness YC Laser Rigging Instructions 12 Vang attached to boom, with control line back to skipper IMG_2217 7/8/2020 Inverness YC Laser Rigging Instructions 13 Half the Outhaul is stored on the boom. It should have been put away like this IMG_2198 7/8/2020 Inverness YC Laser Rigging Instructions 14 Outhaul: Take the line from the end of the boom and attach it to the blue line that is attached to the mast (see IMG_2189) IMG_2199 7/8/2020 Inverness YC Laser Rigging Instructions 15 Preparing to attach the Outhaul. Make sure the mast portion is not twisted IMG_2201 7/8/2020 Inverness YC Laser Rigging Instructions 16 Making the mid-boom Outhaul connection IMG_2203 7/8/2020 Inverness YC Laser Rigging Instructions 17 Another view of previous IMG_2204 7/8/2020 Inverness YC Laser Rigging Instructions 18 Mast portion of Outhaul is now connected to the boom portion of Outhaul. IMG_2205 7/8/2020 Inverness YC Laser Rigging Instructions 19 Another view of Outhaul. Outhaul is fully rigged, with (blue) vertical line down to deck block and then to deck cleat IMG_2207 7/8/2020 Inverness YC Laser Rigging Instructions 20 Special focus on Cunningham 7/8/2020 Inverness YC Laser Rigging Instructions 21 General view IMG_2200 7/8/2020 Inverness YC Laser Rigging Instructions 22 Close-up of previous. Black arrow shows line to be run up on the Starboard side, thru the tack grommet, and then down to connect to the upper Cunningham block on the Port side of the boom IMG_2200 7/8/2020 Inverness YC Laser Rigging Instructions 23 Previously identified line run up past the boom on the Starboard side, then thru the grommet IMG_2206 7/8/2020 Inverness YC Laser Rigging Instructions 24 Another view of previous IMG_2207 7/8/2020 Inverness YC Laser Rigging Instructions 25 Preparing to attach the Cunningham IMG_2208 7/8/2020 Inverness YC Laser Rigging Instructions 26 Close-up of previous. Again, black arrow shows portion of Cunningham that goes up through the grommet in the tack IMG_2209 7/8/2020 Inverness YC Laser Rigging Instructions 27 Attaching the line shown in the previous photo to the upper block of the Cunningham assembly on the Port side. In his left forefinger and thumb, Greg is holding the part of the Cunningham line that goes down to the deck block. IMG_2211 7/8/2020 Inverness YC Laser Rigging Instructions 28 Same as previous IMG_2212 7/8/2020 Inverness YC Laser Rigging Instructions 29 Top of Cunningham is attached. Greg is about to run the Cunningham line thru the deck block. IMG_2213 7/8/2020 Inverness YC Laser Rigging Instructions 30 Cunningham fully rigged thru deck block and back to skipper. IMG_2215 7/8/2020 Inverness YC Laser Rigging Instructions 31 Line that keeps the rudder from kicking up Close-up of previous showing rudder line IMG_2226 cleated to tiller IMG_2230 7/8/2020 Inverness YC Laser Rigging Instructions 32 Dagger board – connect bungee line (arrow) to clips on board Two pins secure the tiller to the rudder IMG_2231 (circled) IMG_2241 Afterdeck should look like this IMG_2244 Now slide the boat down the ramp. If you are using the inner float, watch out for this protruding bolt when sliding the hull down the ramp! See next. IMG_2234 7/8/2020 Inverness YC Laser Rigging Instructions 33 Close-up of previous – nasty lurking bolt will put furrows in the hull if you are not careful! IMG_2233 ON THE DOCK, READY TO DEPART: • Outhaul: put the hook on the boom through the grommet in the clew and adjust the outhaul to desired tightness. • Put down the board and you’re ready to go! 7/8/2020 Inverness YC Laser Rigging Instructions 34 Bon Voyage ! IMG_2245 After sailing, pull the boat up the ramp onto the trailer IMG_2250 Wrap the lines back around the lower mast Tie the bowline to the dolly IMG_2252 section. It should look like this when put away. IMG_2253 7/8/2020 Inverness YC Laser Rigging Instructions 35 Folding the sail IMG_2166 Folding the sail (continued) IMG_2170 Folding the sail (cont) IMG_2175 Folding the sail (concluded) IMG_2177 7/8/2020 Inverness YC Laser Rigging Instructions 36 Putting away the Laser • Wash everything that got wet (including the sail). • Allow sail to dry. Everything else can be put away wet. • Put all the gear on top of the boat and in the cockpit. • Put the cover on and roll the boat back into its stall. - END - 7/8/2020 Inverness YC Laser Rigging Instructions 37.
Load more

Recommended publications
  • King Tides King Tides Are Simply the Very Highest Tides of the Year
    Volume XVIII, No. 07 JULY 2017 July 2017 King Tides King Tides are simply the very highest tides of the year. They are naturally occurring, predictable events associated with the alignment of the moon and the sun orbits to maximize the gravitational pull on the earth. In Hawai‘i these typically occur in the summer months (June and July and December and January. Continued on next page Inside this issue: July 2017 King Tide Attachments “100 years of lifeguarding on O‘ahu” Mangoes return for the 9th annual “Mangoes at the Moana” at Over the Rainbow at Hilton Hawaiian Village The Moana Surfrider, A Westin Resort Spa Makana presented to Hokulea crew on world-circling Renowned artist brings dazzling Hawaii wildlife art event to Malama Honua Voyage on display at Hawaii Convention Center The Moana Surfrider, A Westin Eesort & Spa Four new merchants announced at Pualeilani Atrium Shops WBW celebrating a decade of dining and distinction 47th Annual ‘Ukulele Festival Royal Hawaiian Center news, promotions, entertainment and events Top of Waikiki announces July Special Outrigger Resorts & Henry Kapono present Artist to Artist Concert Series Ron Richter named Dir of Food & Bev at Sheraton Waikīkī Dukes Lane Market & Eatery news Upcoming Ala Moana Centerstage shows Top of Waikīkī July Specials Honolulu Zoo Society’s Wildest Show in Town Sheraton Princess Kaiulani – Hot News International Market Place welcomes Phillip Lim boutique The Surfjack presents – July at the Swim Club Waikīkī Hula Show at the Kūhiō Beach Hula Mound WBW Nā Mele No Nā Pua Sunday concerts WBW July Entertainment & Activities Kani Ka Pila July Entertainment calendar WIA 2017 Ho‘owehiwehi Awards .
    [Show full text]
  • ​470 Rigging Instructions
    ​470 Rigging Instructions 1. Stepping the mast up. a. Ensure the mast partner slit is open. b. With the boat on the grass, step inside (clean or remove shoes first!), and receive the mast. i. Ensure the heel of the mast is clean. ii. If continuous jib sheet, ensure around the mast slot. c. Place the heel of the mast in the shoe inside the boat d. Lean the mast forward, against the deck. e. Free the forestay and attach it. f. Free the shrouds and trapeze, ensure not twisted, and attach them. g. Free the other controls (vang, cunningham, spinnaker halyard, topping lift, down haul), ensure not twisted and attach them. h. Close the mast partner slit. 2. Rigging the boat a. Attach the tack and head of the jib. b. Run the foot of the main sail through the boom, attach the clew and tack. i. On some boats the tack can only be attached after the boom is secured in the gooseneck. ii. On some of the boats it is easier to hoist the mainsail and latch its halyard first, and only then attach the gooseneck and the tack. c. Attach the all 3 ends of the spinnaker and bag it. i. Note: the spinnaker lines should be the outermost, while its halyard stays close to the mast (between the jib lines). ii. Ensure the halyards are not twisted. d. Hoist the jib and attach the halyard cable loop to the tensioner hook. i. VERY IMPORTANT: Make sure the hook catches the metal cable loop and not the messenger line!!! e.
    [Show full text]
  • Specifications and Features Tartan 115 | Specifications & Features
    115 Specifications and Features Tartan 115 | Specifications & Features Sophisticated Designs • Exceptional Performance • Superior Value At Tartan Yachts we have a passion for producing the best high performance racer/cruisers on the market. For over 50 years, our commitment to design and engineering has been based on integrating innovative designs and industry leading technologies that deliver sailing yachts of uncompromising performance. Our designers, builders and sales team understand and appreciate that every yacht we build must be the best yacht we build. At Tartan Yachts we are committed to providing the best owner experience the industry has to offer. Hull • NPG Isophthalic gelcoat • Internal structural grid designed to carry rig • Infused BPA modified epoxy hull and keel loads, glass taped into hull • Locally reinforced at high load areas • UL and ABS approved, corrosion free Marelon flush thru hull fittings • Closed cell synthetic foam hull coring • All hull penetrations made into solid fiberglass “core windows” • Resin infused hull laminated in “one shot” eliminating • Built to meet ABS Plan Certification secondary bonding of structural materials • Transferrable 15-year hull structural and blister warranty • Interior surfaces painted out with enamel gelcoat for aesthetics Deck • NPG Isophthalic gelcoat • Infused BPA modified epoxy deck • CNC computer cut sealed end grain balsa coring • Locally reinforced at high load areas • Molded nonskid surface on working areas • All deck penetrations made into solid fiberglass “core windows” • 6061 T6 aluminum backing plates added at lamination for all loaded hardware • Inward facing hull flange with integrally molded 6061 T6 aluminum bar forming a full length backing plate for hull to deck joint • Hull to deck joint fasteners, stainless steel to meet or exceed ABS standard for offshore use • Hull to deck joint bonded with 3M 5200 adhesive sealant Keel & Ballast • 4,200 lb.
    [Show full text]
  • Viper Owner's Manual.Pdf
    Contents Contents ........................................................................................................................................................................ 1 Introduction .................................................................................................................................................................. 4 About this Owner’s Manual ......................................................................................................................................... 4 General Information .................................................................................................................................................... 5 Assembly ....................................................................................................................................................................... 7 Glossary ....................................................................................................................................................................... 7 Tools needed ................................................................................................................................................................ 8 Arrival of goods ........................................................................................................................................................... 8 Platform ......................................................................................................................................................................
    [Show full text]
  • Newsletter Nov 2009-FINAL to Printer-4
    POLYNESIAN VOYAGING SOCIETY volume III December 2009 Training the Next Generation Expanding the oppor- islands or taking part kind, while honoring tunity to participate in deep sea voyages. our heritage and per- CREW TRAINING in PVS’ crew training petuating our culture. Beginning in May, Ho- SCHEDULE: program is another kule’a will undergo an Sailing on this world- Tuesdays & Thursdays venue for our organi- extensive dry dock. wide voyage will re- zation to perpetuate 5:30 p.m. All hands are welcome quire taking part in the culture & traditions. Marine Education & & needed. All of this Crew Training Program According to Crew Training Center training will culminate & Canoe Building/Dry Training Director 10 Sand Island Parkway with a four-year Dock work. In addi- BRUCE BLANKENFELD, Worldwide Voyage, tion, all crew must this is a golden oppor- targeted to begin in pass an ocean safety/ tunity for anyone who 2012. swim test & have a has ever entertained clean bill of health. the idea of sailing on The theme for this Opportunity for Hokule’a. There is world voyage is Come down to register the next something for every- “Malama Honua” & get acquainted with generation. one — be it sailing where we share the the programs that PVS offshore Oahu, sailing message of caring for has to offer. Schedule between the Hawaiian the Earth & human- is posted at right. 1 Experiencing Pristine Palmyra On March 10, 2009, after 10 days of waiting for clear skies, crew members of Hokule'a and Kama Hele set sail on a training voyage to Palmyra Atoll. The majority of crew had never been on a deep sea voyage on Hokule'a.
    [Show full text]
  • Sailing Course Materials Overview
    SAILING COURSE MATERIALS OVERVIEW INTRODUCTION The NCSC has an unusual ownership arrangement -- almost unique in the USA. You sail a boat jointly owned by all members of the club. The club thus has an interest in how you sail. We don't want you to crack up our boats. The club is also concerned about your safety. We have a good reputation as competent, safe sailors. We don't want you to spoil that record. Before we started this training course we had many incidents. Some examples: Ran aground in New Jersey. Stuck in the mud. Another grounding; broke the tiller. Two boats collided under the bridge. One demasted. Boats often stalled in foul current, and had to be towed in. Since we started the course the number of incidents has been significantly reduced. SAILING COURSE ARRANGEMENT This is only an elementary course in sailing. There is much to learn. We give you enough so that you can sail safely near New Castle. Sailing instruction is also provided during the sailing season on Saturdays and Sundays without appointment and in the week by appointment. This instruction is done by skippers who have agreed to be available at these times to instruct any unkeyed member who desires instruction. CHECK-OUT PROCEDURE When you "check-out" we give you a key to the sail house, and you are then free to sail at any time. No reservation is needed. But you must know how to sail before you get that key. We start with a written examination, open book, that you take at home.
    [Show full text]
  • Sunfish Sailboat Rigging Instructions
    Sunfish Sailboat Rigging Instructions Serb and equitable Bryn always vamp pragmatically and cop his archlute. Ripened Owen shuttling disorderly. Phil is enormously pubic after barbaric Dale hocks his cordwains rapturously. 2014 Sunfish Retail Price List Sunfish Sail 33500 Bag of 30 Sail Clips 2000 Halyard 4100 Daggerboard 24000. The tomb of Hull Speed How to card the Sailing Speed Limit. 3 Parts kit which includes Sail rings 2 Buruti hooks Baiky Shook Knots Mainshoat. SUNFISH & SAILING. Small traveller block and exerts less damage to be able to set pump jack poles is too big block near land or. A jibe can be dangerous in a fore-and-aft rigged boat then the sails are always completely filled by wind pool the maneuver. As nouns the difference between downhaul and cunningham is that downhaul is nautical any rope used to haul down to sail or spar while cunningham is nautical a downhaul located at horse tack with a sail used for tightening the luff. Aca saIl American Canoe Association. Post replys if not be rigged first to create a couple of these instructions before making the hole on the boom; illegal equipment or. They make mainsail handling safer by allowing you relief raise his lower a sail with. Rigging Manual Dinghy Sailing at sailboatscouk. Get rigged sunfish rigging instructions, rigs generally do not covered under very high wind conditions require a suggested to optimize sail tie off white cleat that. Sunfish Sailboat Rigging Diagram elevation hull and rigging. The sailboat rigspecs here are attached. 650 views Quick instructions for raising your Sunfish sail and female the.
    [Show full text]
  • Assembly-Manual-F18-Evolution.Pdf
    ASSEMBLY MANUAL ! CAREFULLY READ THIS MANUAL BEFORE OPERATING YOUR NACRA. Dear Customer, Thank You for purchasing a Nacra F18 Evolution. Before you start using this Nacra, read this Operator’s Manual and owner’s Manual carefully and familiarize yourself with this boat and its operations. For your own safety and a longer operating lifespan of your brand new Nacra, follow the instructions and warning notices in this Manual and owner’s manual carefully. Outside manuals we have an extensive dealer network around the world. Naturally, these Nacra dealers knows everything there is to know about your Nacra and can provides you with the best service possible. So please call your dealer in your region for any servicing needed and make sure that only genuine spares are used for your Nacra. This manual will familiarize you with the operation and maintenance of your new Nacra. It will also provide you with important safety information which should be read and understood before moving on to assemble your Nacra. If this is your first sailboat, or you are not familiar with this kind of sailboat? For your own comfort and safety, please ensure that you obtain handling and operating experience before assuming control of this Nacra catamaran. Nacra Sailing experience centres, National Sailing Federations or yacht clubs will be pleased to advise you about sailing schools or competent instructors. When you have any query, please feel free to contact your local dealer. Manuals can also be found on our website https://www.nacrasailing.com/support/ Table of Content 0. Tools ................................................................................................................................................................................................ 5 1. Platform assembly .......................................................................................................................................................................
    [Show full text]
  • Catboats of the Point
    Table 1 year built owner(s) name builder description Source Other information 1833 Julia Frederick, Charles 23’ Point Boat thought to be JL the first “catboat” at that time labeled “Point Boat” in drawing by Frederick 1852 Peggoty Barker, Bob 17.5’ x 8’ One of the fist catboats. Used as a ferry between Little Compton and Middletown. Later used for fishing. 1852 1879-89 Joshua Collector Pratt 27.5 x 11.4 x 3.4 JL She served as a waterboat in Newport Harbor for many years. She was Sayre broken up in 1899 1870 Frank James Jack Rose Barker, John W. one of a series of “Rose cats” built by George and Harold Baker on purchased by Bill and W.H. Long Wharf in the 1890s Primrose, Rose, Wild Rose MacLeod then Good example of a Newport Cat said to have have been anchored off owned by Arakel 72 Washington St for a year in the 1960s Bozyan 1870 Frank James Primrose Barker, John W. 16’ JL book says that Primrose was built in the 1890s and was one of the and W.H. Rose cats that also included Jack Rose, Rose and Wild Rose 1870 Frank James Rose Barker, John W. 15.0’ one of a series of “Rose cats” built by George and Harold Baker on and W.H. Long Wharf in the 1890s Jack Rose, Primrose, Wild Rose 1870 Mr. Burnham Wild Rose Barker, John W. 23.5’ one of a series of “Rose cats” built by George and Harold Baker on and W.H.
    [Show full text]
  • The First Fifty Years People, Memories and Reminiscences Contents
    McCrae Yacht Club – the First Fifty Years People, Memories and Reminiscences Contents Championships Hosted at McCrae ...................................................................................................2 Our champion sailors...........................................................................................................................5 Classes Sailed over the years.......................................................................................................... 12 Stories from various sailing events.............................................................................................. 25 Rescues and Tall Tales...................................................................................................................... 31 Notable personalities........................................................................................................................ 37 Did you know? – some interesting trivia.................................................................................... 43 Personal Recollections and Reminiscences .............................................................................. 46 The Little America’s Cup – what really happened ….. ............................................................ 53 McCrae Yacht Club History - firsts ................................................................................................ 58 Championships Hosted at McCrae The Club started running championships in the second year of operation. The first championships held in 1963/64
    [Show full text]
  • 420 Tuning Hints
    420 Tuning suggestions College of Charleston 2012 Boat Setup on land: 1) Before sailing check that your shroud pin/ring dings are taped and secure, your tiller extension universal is solid, there’s no wiggle in your pintles and your hiking straps knots secure. 2) Tie your main halyard to the head of your main with a figure eight through the headboard grommet and then a half hitch back around the halyard. (see picture) 3) Hoist your jib and tension the rig tightly by placing a foot on the bow and pulling on the head stay while your team mate tensions the jib halyard. Don’t be afraid to over tension at this point as you’ll double check and most likely reset the tension once on the water. It’s easier to loosen once sailing than to tighten it! 4) Hoist your main and tension the halyard tightly. Use the 2:1 purchase to sock it up tight to the top of the mast. Again, it’s much easier to set it up tight on the dock than to rehoist once sailing! Set up on the water, before the start: 1) Trim your sails and head upwind. 2) Watch/study your leeward shroud as it is your guide to proper rig tension (through jib halyard tension). 3) Ideally the leeward shroud will just start to slacken to the point a slight wiggle (not more than ½”) is visible when the main is sheeted to maximum trim for the breeze/conditions at that time. Note: The advantage of using the “leeward shroud wiggle” is that you can gauge the amount of tension based on a given condition.
    [Show full text]
  • January 2017
    Pipers C of C’s Bluegrass Hoover Fling Clamdigger HIGHLANDER Volume LXIII, No. 1 January 2017 The !1 The HIGHLANDER President's Pespective Official publication of The Highlander Class As I write this, it’s looking to be 14 degrees tonight and International Association Highlander Web Page blustery, Not typical Highlander weather. As I sit at home www.sailhighlander.org without Skye winterized, I wonder how many of the projects I Webmaster: Boyd Barnwell will actually complete on the boat before mid winters… and if [email protected] Editor: Gillian Bauer I will be able to find where I “stored” all her gear… that's next [email protected] year’s issue! President: Chris Hansen [email protected] 2016 was a good year for the Highlander fleet! We had Charlestown, RI good breezes, too big breezes, and no breezes; and that was Executive Secretary-Treasurer just one regatta! The 50th Pipers was a great turnout this year. Debbie Busbey The weather was fickle in the breeze department but otherwise Greer, SC, [email protected] P: 864-244-6433 a great weekend and an awesomely hosted regatta. I was glad to see so many HCIA members travel to support such a Commodore: Doug Fisher Xenia,OH, [email protected] monumental regatta despite the weather predictions. Vice President: Pete Breidenbach Looking forward to the 2017 season, I am brought to one Vandalia, OH of my favorite subjects; youth sailing. As none of us are getting Secretary: Ashley Breidenbach younger (except the ladies, of course) getting youth involved in Englewood, OH the Highlander class is a huge issue for me.
    [Show full text]