Owner's Manual Carefully and Familiarize Yourself with the Equipment Descriptions and Operating Instruc- Tions Before Driving

BSVI OWNER’S MANUAL

CUSTOMER ASSISTANCE In our constant endeavor to provide assistance and complete You can also approach nearest TATA MOTORS dealer. A sepa- service backup, TATA MOTORS has established an all India cus- rate Dealer network address booklet is provided with the tomer assistance centre. Owner’s manual. In case you have a query regarding any aspect of your vehicle, TATA MOTORS 24X7 Roadside Assistance Program offers tech- our Customer Assistance Centre will be glad to assist you on nical help in the event of a breakdown. Call the toll-free Road- our Toll Free no. 1800 209 7979 side Assistance. For additional information, refer to "24X7 Roadside Assis-

tance" section in the Owner’s manual.

ii FORWARD

Dear Customer,

Welcome to the TATA MOTORS family.

We congratulate you on the purchase of your new vehicle and are privileged to have you as our valued customer.

We urge you to read this Owner's Manual carefully and familiarize yourself with the equipment descriptions and operating instructions before driving.

Always carry out prescribed service / maintenance work as well as any required repairs at an authorized TATA MOTORS Dealers or Authorized Service Centre’s (TASCs). Use only genuine parts for continued reliability, safety and performance of your vehicle.

You are welcome to contact our dealer or Customer Assistance toll free no. (1800 209 7979) in case of any query or support required.

We wish you a safe and pleasant driving experience.

iii IMPORTANT INFORMATION  Before driving, read this Owner’s manual carefully and familiarize yourself with your vehicle. For your own safety and a longer vehicle life, follow the instructions, ‘Warnings’ and ‘Notes’ in this manual. Ignoring them could result in damage to the vehicle or personal injury to you or others.

 The Owner’s manual and other booklets are important documents and should always be kept in the vehicle. If you sell the vehicle, always pass on the documents to the new owner.

 This Owner's Manual describes all variants of the model and all standard/optional equipment of your vehicle available at the time of printing. Please note that your vehicle may not be equipped with all features described.

 TATA MOTORS Limited reserves the right to introduce changes in the design, equipment and technical features without any obligation to install them on the vehicles previously sold. The equipment in your vehicle may therefore differ from that shown in the descriptions and illustrations.

 Do not carry out any modification including fitment of non-genuine accessories on your vehicle. Safety, handling, performance and durability, may otherwise be adversely affected and may violate government regulations. TATA MOTORS Limited accepts no liability for damage resulting from the modifications or use of non-genuine accessories.

1 Safety 2 Opening & Closing 3 Dashboard & Features

Important Information 01 Keys 25 Cockpit 47

Safe Driving 01 Doors 33 Instrument Cluster (for TFT) 48

Seat Belts 04 Windows 34 Driver Information System 52

Child Restraint System (CRS) 08 Bonnet Opening 36 Display Messages 61

Air Bags 12 Tailgate Opening 38 Instrument Cluster (for LCD) 69

Child Lock 19 Fuel Lid 40 Driver Information System 73

Anti-theft Device: Immobilizer 20 Power Sunroof 41 Display Messages 78 12 ABS 21 Tell Tales 81

EBD 22 Audio Reminders 90

Additional safety features 22 Combi Switches 91 20

Fascia Switches 94

v CONTENTS

3 Dashboard & Features 3 Dashboard & Features 4 Stowage Areas

Steering Wheel Switches 95 Puddle / Ajar Lamp 102 Glove Box 107

Mic 97 Roof Lamp 102 Goggle Holder 108

Infotainment System Display 97 Side Reading lamps 103 Utility Pockets on Front Doors 108

Speakers & Tweeter 98 Boot Lamp 104 Utility Pockets on Rear Doors 109

USB/AUX 98 Side Indicator Lamp Mobile / Wallet Stowage 109

on ORVM 104 Smart charger 99 Cup Holder 109

Front Lamp 104 Power Socket 99 Stowage for Rear Passenger 110 Tail Lamp 105 Antenna 100 Stowage below Arm Rest 110

Roof Grab Handles 100 Foldable Arm Rest 110

Front Fog Lamp 101 Tailgate Compartment 111

Rear Fog Lamp 101

vi CONTENTS

4 Stowage Areas 5 Climate Control 6 Starting & Driving

Hooks 112 Air Distribution 113 Pre-Driving Checks 125

Front seat back pockets 112 Air Vents 114 Driving Tips 126

Side vent for rear passenger 114 Seat Adjustments 129

Rear Seat folding 132 HVAC Controls 115

Rear View Mirrors 134 Fully Automatic Temperature Control (FATC) 119 Sun Visors 137

Quick Cooling 124 Steering Wheel Adjustments 138

HVAC Sensors 124 Steering Lock Cum Ignition Switch 138

Starting and Stopping 139

Gear Shifting & Driving 141

vii CONTENTS

6 Starting & Driving Starting & Driving Emergency & Break- 6 7 down Assistance Reverse Gear 141 Vehicle Parking 158 Emergency Equipment 173 Braking 142 Reverse Park Assist 159 Hazard Warning Switch 176 Automatic Transmission 142 Reverse Park Assist with Sensor 159 In Case of Flat Tyre 176 Shift Lever Manually Unlock 145 Reverse Park Assist with Jump Lead Starting 180 Shift Lock System 148 Camera 162 Towing 182 Starting and Stopping (PEPS) 150 Drive Mode 169

145 Fuses 184 Starting the Engine 152 Terrain Response Mode 169 145 Bulb Specification 194 Gear Shifting and Driving 154 145 24x7 Road Side Assistance 196 Braking 155

Driving 156

Parking Brake 157

viii CONTENTS

8 Maintenance 8 Maintenance 9 Technical Information

Maintenance & Service 201 Exhaust After Fuel Specification 231 Treatment System 223 Engine Compartment 202 Lubricant Specification 232

Oil / Fluid Level 203 Technical Specification 233

Battery 207 Vehicle Dimensions 237

Tyres 210 Aggregate Identification Nos 238

Remote Key Battery Replacement 212

On Board Diagnostic (OBD) 214

Diesel Particulate Filter 215 (DPF) Warning Indicator

Service Schedule 216

Parking for Long Durations 223

ix CONTENTS

Car Care and Value Warranty – Terms and 10 11 12 Environment Safety Added Services Conditions

Car Care 239 Warranty – Environment Safety 255

Terms & Conditions 253 Washing 239

Waxing 240

Polishing 240

Interior Fabric Cleaning 240

Paint Care 241

Wiper Care 241

Value Care AMC 242

Extended Warranty 246

Value Added Services 248

x SAFETY Important Information Safe Driving Safety Tips In this Owner's Manual, you will find the Safety consciousness not only ensures  Always take into account the road text under the heading “WARNING” and your safety and the safety of other road conditions, weather conditions, vehi- “NOTE” which highlights important infor- users, but it also helps to reduce the cle speed in order to prevent acci- mation. Pay particular attention to these wear and tear on your vehicle. dents. highlighted messages. Safe driving depends on:  Turn ‘ON’ the side indicators at least 30 meters before taking a turn or  How quickly you make decisions to NOTE changing the lane. Indicates additional information avoid an accident.  Decelerate to a safe speed before that will assist you in gaining the  Your ability to concentrate. taking turn. Do not apply brakes dur- optimum benefit and care for your ing cornering. vehicle.  How well you can see and judge objects.  When overtaking other vehicles, WARNING  How well familiar you are with your watch out for the oncoming vehicle. Indicates procedures or infor- vehicle controls and its capabilities.  Never drive under the influence of al- mation that must be followed pre- cohol or drugs. NOTE cisely in order to avoid the possibil-  If your vehicle is equipped with info- ity of severe personal injury and se- Fatigue is a result of physical or tainment/navigation system, set and mental exertion that impairs judg- rious damage to the vehicle. make changes to your travel route ment. Driver fatigue may be due to only when the vehicle is parked. inadequate sleep, extended work hours, strenuous work or non-work  Program radio presets with the vehi- activities or combination of other cle parked, and use your pro- factors. Take rest at regular inter- grammed presets to make radio use vals. quicker and simpler.

1 SAFETY

Driving Through Water Driving on a Rainy Day NOTE Do not drive through flooded areas.  Check wiper blades, lights and If you have driven for a long time in Judge the depth of water before driving brakes for proper functioning and heavy rain without braking, there through it. Otherwise, water may enter condition. may be a delayed reaction from the the vehicle interior or the engine com-  Check the tyre treads depth, the con- brakes when braking for the first partment. dition of the tread and tyre. time. You have to press the brake pedal more firmly. Maintain a If at all the situation demands that you  Avoid harsh braking and sharp turns. greater distance from the vehicle in have to drive through water then; It may cause loss of control and lead front.  Keep engine in higher RPM and crawl to a skid. the vehicle in low gear.  For slowing down, shift to lower gears Driving on Snowy Roads and brake gently.  Flowing or rushing water creates While driving in snow, it is advisable to  Keep lights ‘ON’ if visibility is poor. strong forces. Driving through flow- use the snow chain on roads. Follow as- ing water could cause the vehicle to Driving on Wet Roads sembly and safety instruction provided be carried away. Be cautious while by the snow chain manufacturers. driving through flowing water. On wet road or during light showers, “Aq- uaplaning” can occur. “Aquaplaning” is  Lightly apply the brake pedal to dry the loss of direct contact between the the liners until the brakes work nor- road surface and the vehicle’s tires due mally once you are out of water. to a water film forming between them. WARNING Steering or braking the vehicle can be Do not attempt to start the engine very difficult, and loss of control can oc- if vehicle gets flooded due to water. cur. Tow the vehicle to a safe place. There is no hard and fast rule about aq- Contact a nearest TATA MOTORS uaplaning. The best advice is to slow Authorised Service Centre down when the road is wet. 2 SAFETY Night Driving Driving on Gradients Driving on Highway  Ensure that all lights are working and When climbing gradient, the vehicle may Stopping distance progressively in- windshield, window glasses are begin to slow down and show a lack of creases with vehicle speed. Maintain a clean. power. If this happens, shift to a lower sufficient distance between your vehicle  Drive more slowly at night than in the gear and apply power smoothly so that and the vehicle ahead. daytime, as the visual range is re- there is no loss of traction. For long distance driving, perform safety stricted at night. Maintain a speed When driving down a hill, the engine checks before starting a trip and take such that you can stop within illumi- braking should be used by shifting into a rest at certain intervals to prevent fa- nated distance of headlamps. lower gear. Do not drive in neutral gear tigue.  Do not use the high beam unless in- or switch off the engine. evitable. It may dazzle the driver of the oncoming vehicle, thus causing WARNING an accident. On long and steep gradients you  Use headlamp main/dip beam to must reduce the load on the brakes alert other road users on turns/ by shifting early to a lower gear. cross roads etc. This allows you to take advantage  Use side indicators for lane change of the engine braking effect and or turning. helps avoid overheating of service brakes resulting in reduced braking efficiency.

3 SAFETY Seat Belts Buckling the Shoulder Seat Belt Releasing the Seat Belt This section of user manual describes  Grasp the tongue and slowly pull out To release the seat belt, push the red your vehicle seat belt, airbag and Child the seat belt over the shoulder and button on the lock buckle. The seat belt restraints system. Please read and fol- across the chest. When the seat belt will automatically retract to its stowed low all these instructions carefully to is long enough to fit, insert the position. If necessary, slide the tongue minimise risk of severe injury or death. tongue into the lock buckle until you down the webbing to allow the seat belt to retract fully.  Seat belts are the primary restraints hear a “CLICK” which indicates that system in the vehicle. All occupants, the seat belt is securely locked. including the driver, should always  Position the lap portion of seat belt wear their seat belts to minimize the across your pelvic bone (hips), below risk of injury. your abdomen. To remove slack, pull  Sit back and adjust (if equipped), the up a bit on the shoulder seat belt. To seat. Make sure that your seat is ad- loosen the lap portion seat belt if it is justed to a good driving position and too tight, tilt the tongue and pull on the back of the seat is upright. the lap seat belt. A snug seat belt reduces the risk of sliding under the seat belt in a collision. Ensure that the seat belt running over the body (shoulder segment and lap segment) does not have any twist. Twisted seat belt may not offer effective protec- NOTE tion when required. The above images are for reference purpose only.

4 SAFETY Fixed Rear Centre Lap Seat Belt  If the seat belt webbing or Seat Belts with Pre – tensioner hardware is damaged, get it (If equipped)  When buckling, make sure you hear replaced immediately at TATA a click confirming that the tab is You can use pre-tensioner seat belts in Motors Authorized service centre. latched into the seat belt lock. To the same manner as ordinary seat belts. tighten it, pull the loose end through  Do not insert any items such as The seat belt pre-tensioner system the buckle until the seat belt is com- coins, clips, etc. into the seat belt works in conjunction with the fortably adjusted around the pelvic buckles, and be careful not to SUPPLEMENTARY RESTRAINTS SYSTEM bone (hips). spill liquids into these parts. If (SRS-Airbags). foreign materials get into a seat In the event of a collision, as may be WARNING belt buckle, the seat belt will not necessary, pre-tensioner tightens the  Each seating position and seat work properly. seat belt so that it fits the occupant’s belt assembly must be used by  Do not wear seat belts over hard, body more snugly. When pre-tensioner one occupant. It is not sharp or fragile items in clothing, activates, there could be some noise recommended to put a seat belt such as pens, keys, spectacles and release of smoke. This is normal around a child, being carried on etc. and there are no health hazards or fire risk. an occupant's lap.  Do not use any accessories on

 Be careful not to damage or seat belts or modify in any way

tamper the seat belt webbing or the seat belt system. Devices hardware. Inspect the seat belt claiming to improve occupant system periodically, checking for comfort or repositioning the seat cuts, frays, or loose parts. A belt, can reduce the protection frayed or torn seat belt could rip provided by the seat belt and apart in a collision and leave you increase the chance of serious injury in a collision. with no protection.

5 SAFETY

WARNING Seat Belt with Load Limiter Use of seat belts for pregnant woman In a collision, the pre-tensioner (If equipped) seat belt assembly mechanisms You can use the load limiter seat belts in WARNING become hot during activation. Do the same manner as ordinary seat belts. not touch the pre-tensioner seat  Pregnant woman must wear a The seat belt load limiter system works correctly positioned seat belt. It belt assemblies for several in conjunction with the SUPPLEMEN- minutes after they have been is safer for mother as well as TARY RESTRAINTS SYSTEM (SRS-Air- activated. unborn child. bags).  Pregnant woman should wear If the vehicle has been involved in a In the event of a collision, as may be nec- the lap part of the seat belt collision, get it inspected immediately at essary, load limiter reduces the load on across the pelvic bone (hips) and authorised TATA MOTORS SERVICE the rib cage region of the occupant. as snug across the hips as Center. If the vehicle has been involved in a col- possible. Keep the seat belt low lision, get it inspected immediately at Au- so that it does not come across thorised TATA MOTORS SERVICE Center. the abdomen. That way the strong bones of the hips will take the force if there is a collision.

6 SAFETY Seat Belt Warning Lamp  If front passenger seat is occupied by child, system may detect occupancy and warn with front passenger seat belt warning. It is not taken to mean child can occupy front passenger For Driver For Front seat and use seat belt. Please refer Passenger CRS section for recommended seating position. The seat belt warning lamp reminds you to fasten the seat belt. NOTE  If the driver does not fasten seat belt, Using unauthorized after-market seat belt reminder lamp will blink seat cover may affect function of and a buzzer will sound for pre- occupant sensor. TATA motors defined duration until the driver’s does not recommended any non- seat belt is buckled. validated seat covers on seats.  If front passenger seat is occupied by adult and does not fasten seat belt, seat belt reminder lamp will blink and a buzzer will sound for pre- defined duration until the front passenger seat belt is buckled.  If this system is also provided for other than Front row seats, applicable above warnings will appear until seat belts are buckled.

7 SAFETY Child Restraint System (CRS) Once your child outgrows the forward- facing CRS, your child is ready for a TATA MOTORS strongly recommends the booster seat. use of Child Restraint Systems (CRS) for all children up to age of 12 years and to Selection and Installation of CRS: be placed at recommended positions only. Children travelling without recom- Always select the CRS that complies with latest safety standards (AIS072 / ECE mended CRS and seated at other posi- R44). The CRS are classified according tions may face serious injuries in case of to the child's size, height and weight. a collision. Select the appropriate CRS for your CRS can be installed in the vehicle using child. Ensure that the CRS is securely seat belts and/or ISOFIX only (if installed in the vehicle and subsequently equipped) or ISOFIX with Top Tether (if child fits properly in it and wears harness equipped). of CRS. For installation, please refer CRS manufacturer’s instruction manual. The harness system of CRS holds the child in place, and in a collision, acts to keep the child positioned in the seat and reduce the risk of injuries. All children below age of one year must always ride in a rear-facing infant CRS.

Keep children above age of one year, in a forward-facing CRS with a harness un- NOTE til they reach the size or weight limit al- The above images are for reference lowed by your CRS manufacturer. purpose only. 8 SAFETY

Recommended CRS Position Rear Rear Mass Age Front Rear as per the Vehicle Matrix Group Outboard Outboard Group Group Passenger Center The suitability of seat position for LH RH carriage of children and recommended category of CRS is shown 0 Up to 10 Up to 9 X U U X in the table below as per the child kg months group. Up to 13 Up to 24 0+ X U U X X - Seat Position not suitable for kg months children in this age group.

- Suitable for “universal” 9 months to U I 9 to 18 kg X U U X category restraints approved 48 months for use in this age group.

Universal is a category in the Approx. 3 to II 15 to 25 kg X U U X AIS072 / ECE R44 norm. 7 years

WARNING If a child is seated in the Approx. 6 to front seat it may cause III 22 to 36 kg X U U X serious injury or even death 12 years during any collision.

9 SAFETY

WARNING WARNING NOTE If your vehicle is equipped with a Do not use an infant carrier or a  Do not install a booster seat or a front passenger airbag (PAB) and child safety seat that "hooks“ over booster cushion with only the lap does not have PAB deactivation a seatback, it will not provide strap of the seat belt. switch, do not install a rear-facing adequate protection in a collision.  Do not install a booster seat or a CRS in the front passenger seat. If After a collision, we recommend to get booster cushion with a seat belt the PAB inflates, a child in a rear that is slack or twisted. facing CRS could be seriously seat belts, seats, ISOFIX and top-tether injured or killed. anchorages (as may be applicable)  Do not put the safety seat belt investigated at TATA MOTORS under your child’s arm or behind If you install a CRS in the rear seat, slide Authorised service centre. its back. the front seat far enough forward so that  Do not use pillows, books or the child’s feet do not touch the front NOTE towels to boost your child’s seatback. This will help avoid injury to A CRS in a closed vehicle can height. the child in the event of a collision. become very hot. To prevent burns,  Make sure that your children sit check the seating surface and in an upright position. NOTE buckles before placing your child  Do not allow children to stand up Children could be endangered in a in CRS.

or kneel on either the rear or the collision if their CRS is not properly front seats. An unrestrained secured in the vehicle. Be sure to WARNING child could suffer serious or fatal secure the child in the restraint injuries during a collision. system according to the  Do not leave unattended children manufacturer’s instructions. in your vehicle.  Do not leave any toys or other  Do not modify CRS in any way. objects loose in the CRS or on the seat while the vehicle is in motion.

10 SAFETY Each CRS should be used for one child only. When PAB deactivation switch (if provided) is turned ‘OFF’, make sure ‘PAB’ operational status lamp illuminates with ignition ‘ON’, indicating that the passenger airbag is NOT operational. If the airbag SRS warning indicator in the instrument cluster illuminates continuously, it means that there is malfunction in the system. Remove the CRS from front passenger seat and contact your TATA MOTORS authorised service center.

NOTE The above images are for reference purpose only. 11 SAFETY Supplementary Restraint System Airbag ECU judges that the signals breathing problems , in such cases get (SRS - Airbags) (if equipped) represent a severe collision, will trigger fresh air promptly. the airbags. The inflated Airbags provide After inflation, airbag provides a gradual The airbag ‘SRS’ system comprises of a cushion to the occupants. The Airbag cushioning effect for the occupant the following components depending inflates and deflates so quickly that you thereafter deflates. It is not advisable to upon the provided safety features in may not even realize that it has vehicle. activated. The Airbag will neither hinder drive your vehicle after the airbags have been deployed. If you are involved in your view nor make it hurdle to exit the  Seat belt Pre-tensioners another collision, the airbags will not be vehicle.  Seat belt with load limiters in place to protect you.  Driver Airbag Airbag inflation is virtually instantaneous and occurs with considerable force,  Front Passenger Airbag accompanied by loud noise and smoke,  Side Airbags (if equipped) which is normal. The inflated airbag,  Curtain Airbag (if equipped) together with seat belts, limit the movement of an occupant, thereby  Airbag ‘SRS’ ECU (Electronic reducing the risk of injury. Control Unit)  Collision Sensors When an airbag inflates, you may see  SRS wiring harness some smoke-like particles. The particles are a normal by-product of the process  SRS Warning lamp that generates the non-toxic gas used for The System is active when ignition airbag inflation. These airborne particles switch is in the “ON” position or the may irritate the skin, eyes, nose, or ignition mode is “ON”. Airbags are throat. If you have skin or eye irritation, NOTE designed to inflate in severe collisions. rinse the area with water. For nose or The above images are for reference In the event of a collision, the collision throat irritation, move to fresh air. Also purpose only. sensors will detect signals, and if the sometimes the smoke can cause 12 SAFETY NOTE Side airbags (if equipped), are mounted Curtain airbags (if equipped), are in front row seats for outboard mounted above the doors along the roof  Open your windows and doors as occupants only. on both sides. soon as possible after collision to reduce prolonged exposure to the smoke and powder released by the inflating airbag.  Do not touch the airbag container’s internal components immediately after an Airbag has inflated. The parts that come into contact with an inflating Airbag may be very hot.  Always wash exposed skin areas thoroughly with lukewarm water and mild soap. NOTE The driver airbag is mounted in the NOTE The above image is for reference centre of the steering wheel. The front purpose only. The above image is for reference passenger airbag is located inside the purpose only. dashboard in front of the passenger seat. The vehicle fitted with the airbags have suitable indications on steering wheel and on dash board. The word ‘AIRBAG’ is embossed on the airbag covers.

13 SAFETY

WARNING their feet on the floor until the Not Recommended Seating  Even in vehicles with Airbags, you vehicle is parked and the engine Position and your passengers must is turned off. always wear the seat belts  If an occupant is out of position provided. In order to minimize during collision, the rapidly the risk and severity of injury in deploying Airbag may forcefully the event of a collision. contact the occupant causing  ALWAYS use seat belts and CRS serious or fatal injuries. – during every trip and at all  Do not allow the front passenger times. Even with airbags, you can to place their feet or legs on the be seriously injured or killed in a dashboard. collision if you are not wearing seat belt properly or not wearing seat belt when airbag inflates.  You and your passengers should NOTE never sit or lean unnecessarily close to the Airbags. The above images are for reference purpose only.  Move your seat as far back as possible from front Airbags, while still maintaining control of the vehicle.  All occupants should sit upright with the seatback in an upright position, centred on the seat cushion with their seat belt on, legs comfortably extended and

14 SAFETY Not Recommended Seating Position

NOTE

The above images are for reference purpose only. 15 SAFETY

WARNING collision or sudden stop, causing WARNING injuries to occupants in the If your SRS malfunctions, the Airbag  Never place your arm over the vehicle. airbag as a deploying airbag can may not inflate properly during a col- result in serious arm fractures or  Coat hooks (if provided), must be lision thereby increasing risk of seri- other injuries. used only for that purpose. Never ous injury or death. If any of the fol- hang other items on to those  Do not allow the passengers to lowing conditions occur, your SRS is hooks. This could affect malfunctioning: lean their heads or bodies onto deployment of the Airbags, and  The SRS warning lamp does not doors or place objects between may lead to severe to fatal turn ‘ON’ when the ignition switch the doors and passengers when injuries. they are seated on seats is placed in the ‘ON’ position for equipped with side and/or  ALWAYS contact your TATA few seconds. MOTORS authorised service curtain Airbags.  The SRS warning lamp stays ‘ON’ centre if the vehicle is damaged, after illuminating  Do not place or stick any item/s even if airbag has not inflated. in the vehicle, except at  The SRS warning lamp comes  ALWAYS contact your TATA designated locations (such as ‘ON’/stays ‘ON’ while the vehicle MOTORS authorised service utility bins, cup/bottle holders, is in motion. boot space etc). Loose items centre if any part of an airbag  The SRS warning lamp blinks may act as a projectile during a module cover shows sign of when the engine is running. collision and cause severe to cracking or damage. fatal injuries. We recommend the customer to immediately visit TATA MOTORS author-  Please be aware that any ised service centre and get the SRS unsecured item in your vehicle, system inspected if any of the above such as your pet, unsecured CRS conditions occur. or a laptop, can become a potential hazard in the event of a

16 SAFETY

WARNING performance of system and may It is not taken to mean child can occupy cause serious injury or death. front passenger seat and use seat belt.  Never make any modifications to Please refer CRS section for recom- your vehicle. The modifications Airbag Warning Sticker on Front mended seating position for children. carried out, but not limited to the Passenger Sun Visor vehicle frame, bumpers, front WARNING fenders, ride height, suspension, Never use a rearward facing child seat belts, interior trims, steering restraint on a seat protected by an wheel (especially holders), are active Airbag in front of it, Death or not acceptable. This will affect serious injury to the child can oc- the intended performance of cur. SRS system.

 Fitment of bull bars, seat covers on seats with airbags etc, is strictly prohibited, unless authorised by TATA MOTORS. This will affect the intended performance of SRS system.  If you need to make any modifications to accommodate any disability you may have, please contact your Authorized The Airbag Warning Symbol on sun visor TATA MOTORS Dealer for reminds extreme hazards associated necessary guidance. with the use of rearward-facing child re-  Do not tamper with SRS in any straint on front passenger seat during way. This will lead to unexpected airbag deployment. 17 SAFETY Airbag Deployment Conditions will not protect the occupant. Head re- other fixed objects; the airbags may de- straints and seat belts provide occupant ploy depending upon the severity of col- When front airbags (if equipped) protection during a rear collision. lision. In some of these conditions, dam- should not deploy? age to the vehicle may be minor or not Rollovers collision: During a rollover be readily visible. Minor frontal collision: Seat belt (if collision, unbelted occupants may float worn) offers adequate occupant protec- inside the passenger compartment. This When front airbags/side air- tion in low severity collisions. The air- will increase the risk of injuries and may bags/side curtain airbags (if bags are triggered only when there is a prove to be fatal. Wearing seat belts pro- equipped) may not deploy, even collision severe enough to trigger the air- vide highly effective occupant protection with exterior visible vehicle dam- bags. Deployment of frontal airbags is during rollover collision. Front airbags, age? not beneficial in low severity collisions. are not designed to deploy in a rollover The airbags are triggered only when Side collision: During a side collision, as frontal airbags cannot offer any protection in rollover collision. there is a collision severe enough to trig- occupants tend to move sideways. ger the airbags. The amount of visible ve- Therefore, deploying frontal airbags in When front airbags/side air- hicle damage is not always the correct such situations will not benefit the occu- bags/side curtain airbags (if indicator for airbag deployment. Some pants. Side airbags and side curtain air- equipped) deploy with minor or no collisions can result in visible damage bags (if equipped) are specifically de- visible vehicle damage? but with no airbag deployment, because signed to reduce the injuries that can oc- the airbags would not have been needed cur in side collision. The airbags are triggered only when or would not have provided protection there is a collision severe enough to trig- even if they had deployed. Seat belts, if Rear collision: During a rear collision, ger the airbags. The extent of vehicle occupants tend to move (rearwards) worn, offer adequate occupant protec- damage is not always the correct indication in such cases. away from frontal airbags. Therefore, de- tor for airbag deployment. In some ex- ploying frontal airbags in such situations treme/rare conditions; of rough road driving, running into a curb or hitting

18 SAFETY

Child Lock (if equipped) NOTE  Lift the lock lever upward to deactivate the childproof lock when not required.  Child safety lever to be used for safety of child for preventing them to open rear door while seating in passenger seat to avoid accident while vehicle is running.

Both the rear doors of the vehicle are provided with a child proof lock. Push the lock lever located on vertical face of the door downward before closing the door. The door which has been closed by acti- vating the child lock cannot be opened from inside, it can be opened only from the outside.

19 SAFETY

Anti-Theft Device-Immobilizer/ PEPS NOTE (If equipped) Use only Flip key, the other should be Immobilizer system is designed to pre- kept in a safe location. Note down vent vehicle theft by electronically disa- “key Tag no.” information (and keep it bling the engine ignition system. The en- safe) which is required while getting gine can be started only with vehicle’s new/spare keys. Re-member that it is original Immobilizer ignition key which not possible to prepare new/spare has an electronic identification pro- keys without the “key Tag number.” grammed code. Take pre-caution about Flip key, as without Flip key vehicle cannot be started.

Immobilizer Vehicle Condition Vehicle State Meaning / Function of the state Lamp Status Ignition OFF Blinking Locked Vehicle Immobilized and awaiting electronic key Ignition ON OFF Unlocked Normal condition and ready to start the vehicle - Problem with key (Wrong key used to start vehicle) Ignition ON ON Locked - Problem with Immobilizer system. Contact a TATA MOTORS Authorized Service Centre Ignition ON Blinking Unlocked - Contact a TATA MOTORS Authorized Service Centre immediately

tally

20 SAFETY Anti-lock Braking System (ABS) While Braking judgment. Drive within safety margin taking into consideration pre- (If equipped)  In an emergency situation take your vailing weather and traffic condi- foot off the accelerator and press the ABS regulates brake pres- tions. sure in such a way that the brake pedal fully. This allows the ABS wheels do not lock when to regulate braking for you and have you brake. This allows you to continue steering control along with maximum steering the vehicle when braking. possible braking.  When ABS is active driver will feel The ABS warning lamp in the instrument brake pedal pulsating and very low cluster lights up when the ignition is motor (ABS) activation noise from en- switched on. It goes off after 2-3 sec- gine compartment which is normal onds if system is healthy. during ABS braking.

WARNING WARNING  If ABS is faulty, the wheels could  On certain surfaces, such as lock when braking. The steer abil- gravel or firm ground covered by ity and braking characteristics snow, the standard ABS system may be severely impaired. There may have the effect of increasing is an increased danger of skid- the stopping distance, but ABS ding and accidents. will still offer the advantage of  Drive on carefully. Have ABS helping you to maintain direc- checked immediately at the TATA tional control of vehicle. MOTORS Authorized Service Cen- tre as soon as possible.  However, remember that ABS will not compensate for bad road or weather conditions or poor driver 21 SAFETY Electronic brake force distribution Additional safety features critical situation and to prevent the vehicle rollover. This is done by active brake (EBD) Cornering Stability Control (CSC) EBD monitors and controls interventions on selected wheels, the brake pressure on the Corner stability Control supports / stabi- thereby reducing the forces that cause a rear wheels to improve driv- lizes vehicle during partial braking on roll-over situation. curves by reducing pressure at required ing stability while braking. Brake Disc Wiping (BDW) EBD provides optimal braking pressure inner wheel of the vehicle. Water on the brake disc leads to a delay distribution between front and rear This helps to reduce probability of vehi- in brake response time. The purpose of wheels to optimize braking distance and cle over steering during cornering. to ensure vehicle stability by means of the function Brake Disc wiping is to re- lowering braking pressure at rear OFF Road ABS move moisture when driving in wet con- wheels. Based on wheel speed information off ditions automatically. To get quick response form Brake and better decelera- road ABS helps to avoid wheel lock on WARNING tion. uneven surfaces like loose gravel, pot  If EBD is malfunctioning, the rear holes by reducing the stopping distance Electronic Brake Pre-fill (EBP) wheels can lock, e.g. under full compared to standard ABS. braking. This increases the risk of The Electronic Brake Prefill (EBP) func- skidding and an accident. Electronic Traction Control (ETC) tion reduces the air gap of the brake pad  You should therefore adapt your The Electronic Traction Control system and the brake disc. The function is trig- driving style to the different han- function (ETC) is designed as a slip con- gered after a sudden release of the ac- dling characteristics. Have the trol system to prevent the driven wheels celerator pedal due to an unexpected brake system checked immedi- of a vehicle from excessive wheel slip. emergency brake situation. By actively pre-filling the brake-system the brake re- ately at a TATA MOTORS Author- Roll over Mitigation (ROM) ized Service Centre as soon as sponse time is reduced and results in a The main feature of the Roll over Mitiga- shorter stopping distance. possible. tion function is the detection of a rollover

22 SAFETY Hydraulic Brake Assist (HBA) inner wheels during turning. DWT-B reduces understeer tendency of the car In a dangerous emergency situation, and a higher curve speed can be most drivers don't use the full available achieved. performance of the brake system, because they brake too soft. The HBA func- Engine Drag Torque Control tion detects the critical situation and (EDTC) builds up additional brake pressure to reduce the braking distance. On slippery road conditions during in- gear Braking or Shift down of gear or Hydraulic Fading compensation sudden throttle release on a curve road. (HFC) This causes high Engine drag on the In dangerous fading situations most driv- driven wheel resulting into brake slip sit- ers operate the brake pedal with a small uations without any brake application. or regular braking force and they never reach to the maximum possible vehicle This makes vehicle highly under steera- deceleration. The HFC function improve ble. EDTC controls such brake slip on the the stopping distance by eliminating re- driven wheels by increasing the engine quired pressure build-up lag by the torque to makes the vehicle stable and driver. steerable. Dynamic Wheel Torque by Brake Hill Hold control (HHC) (DWT-B) Hill Hold Control is a comfort function. The main goal of the function is to im- The main intend is to prevent the vehicle prove the agility of a vehicle and to ena- from rolling backwards while driving off ble a more direct steering. This is mainly up-hill on an inclined surface. achieved by braking interventions at the 23

SAFETY

24 OPENING AND CLOSING Keys (as available) SN Name Remote key Description

1. Unlocking all doors 2. Approach light/Tail gate opening 1. Flip key with remote 3. Locking all doors 4. Folding key blade in/out

1. Locking all doors 2. Mechanical key 2. Unlocking all doors

1. Locking all doors 2. Approach light 3. Smart Key (PEPS) 3. Tail gate opening 4. Unlocking all doors

25 OPENING AND CLOSING Keys WARNING Flip Key with Remote A key is an electronic access and author-  Do not turn ‘ON’ ignition switch ization system which is provided as a by using key with any type of standard feature on your vehicle. metal wound around its grip or in contact with it. This may be de- Unlocking Principle tected as abnormal condition by The transponder which is built into the immobilizer and prevent engine ignition key carries a unique identifica- from starting. tion code. The vehicle unlocks when the  Do not leave the key in areas of code on the key matches with the code high temperature. The tran- on the Engine Management System sponder in it will behave abnor- (EMS). In case of PEPS variant, Immobi- mally when reused. lizer function is provided by PEPS.  Do not try to start the vehicle Engine Starting when the Immobilizer 1. Unlocking all doors When the key is inserted and the ignition indicator lamp on the 2. Approach Light/Tail gate unlatch instrument cluster is glowing. In is switched ‘ON’, all codes are communi- this condition the vehicle will not 3. Locking all doors cated within key, Immobilizer and EMS. start and the vehicle’s battery will The engine will start only if all the codes 4. Folding key blade IN/OUT also be drained due to frequent match. cranking. 1. Unlocking all Doors Loss of Keys Pressing the unlock button (1) of remote will unlock all the Doors. One flash is If one of the key is lost, contact your nearest TATA MOTORS authorised coming on side indicators. dealer immediately.

26 OPENING AND CLOSING 2. Approach Light 4. Folding Key Blade IN / OUT Flip Key Features Press approach light button (2) once, low Press button (4) to flip out the key blade. Vehicle Search beam and positon lamp will turn ‘ON’. For folding, press the button (4) and fold In vehicle, locked condition if lock button This feature helps to find and reach the the key blade inside. on remote key is pressed the turn indica- parked vehicle or to reach home in dark/ tors of vehicle flashes for 4 times. cloudy condition after parking. Red LED will be flash on the remote. To switch Automatic Activation of Immobilizer ‘OFF’ the approach lights, press and re- If key is removed from ignition switch, lease the same button or it automatically turns ‘OFF’ after certain time. the engine will be immobilized automatically even if you forget to lock the vehi- Tail Gate Unlatch cle. To unlatch the Tail gate, long press the For few variant, Ignition off is required to approach light button (2) on remote for immobilize the vehicle. more than 2 sec. Auto Locking / Unlocking of Doors /

NOTE Auto Relock

Tail gate once unlatched will not NOTE  Vehicle doors are automatically get lock automatically with doors. Do not fold the key blade without locked when all doors are closed and It will locked by slamming. pressing the button. Also, it should the vehicle speed crosses 10 kmph. 3. Locking all Doors not be forced in any direction apart  When key is taken out all the doors from folding direction to avoid get automatically unlocked. Pressing the Lock button (3) once. Re- damage to flip mechanism.  For few variant, when ignition is mote locks all the doors of the vehicle. turned off all the doors get automatically unlocked.

27 OPENING AND CLOSING Also, when unlocked with remote key Smart Key (PEPS) 1. Locking all Door and if no door is opened within 30 sec- Pressing the Lock button (1) once. Re- onds, vehicle doors get automatically mote locks all the doors of the vehicle. locked. Please refer section starting and driving for more information. Anti-grab / Anti-scan Coding The remote control set of this security 2. Approach Light system is protected against the use of Press approach light button (2) once, low devices called ‘scanners’ and ‘grabbers’ beam and position lamp will turn ‘ON’. which can record and reproduce some This feature helps to find and reach the types of remote codes. parked vehicle or to reach home in dark/ cloudy condition. To switch ‘OFF’ the approach lights, press and release the NOTE same button or it automatically turns In case any button of the key is ac- Keep the smart key with user to perform ‘OFF’ after certain time. cidentally pressed for more than the passive access. It is used for locking, 20 seconds, the remote stops func- unlocking and starting the vehicle. 3. Tail Gate Opening tioning till the time the button is To open the Tail gate press the button (3) 1. Locking all doors pressed. The LED on the Remote once on the smart key, Tail gate will un- also stops glowing. The function of 2. Approach Light latch. Please refer section starting and the remote gets reinstated imme- driving for more information. diately when the user stops press- 3. Tail gate opening ing the push button of remote. 4. Unlocking all Doors 4. Unlocking all doors Pressing the unlock button (4) once. Re- mote will unlock all the Doors. Please refer section starting and driving for more information.

28 OPENING AND CLOSING

NOTE Unlocking Door with Emergency  Outer cover of door handle will be unlock first. If smart key battery is low/drained Key or vehicle battery is low/drained,  Slot is provided below driver door  Remove the cover to access the door user can unlock and enter into ve- handle. lock slot. hicle by using Emergency key blade. Provision is given on driver door handle only. Emergency Key blade In / Out

 Insert the key blade in slot and press.  Insert the key blade in slot and turn clockwise to unlock the door.

Slide the knob (1) to unlatch the key. Pull the key blade (2) out.

29 OPENING AND CLOSING Smart Key Features Auto Locking / Unlocking of Doors / Smart Key Precautions auto Relock Force Panic ON operation 1. If smart key is close to radio transmit- When vehicle is in OFF condition, if we In PEPS variants, door will get unlocked ter such as radio station or an airport press lock button and unlock button sim- when ignition is OFF by pressing Start which can interfere with normal oper- ultaneously, Force panic operation gets Stop switch. ation of the transmitter. 2. If smart key is near a mobile two way activated. In this case, turn indicators of Anti-grab / Anti-scan Coding vehicle start flashing and horn will blow radio system or a cellular phone, automatically. The remote control set of this security then it will not work properly. system is protected against the use of 3. If another vehicle’s smart key is be- Force Panic OFF operation devices called ‘scanners’ and ‘grabbers’ ing operated close to your vehicle, By pressing any button of smart key, which can record and reproduce some signal will fluctuate. Force panic operation gets deactivated types of remote codes. WARNING Vehicle Search Important Keep smart key away from electro- In vehicle locked condition, if lock button  Don’t operate Unlock button of re- magnetic materials that blocks on smart key is pressed, the turn indica- mote in the vicinity of your vehicle, as electromagnetic waves to the key tors of vehicle flashes 4 times. it could lead to an unintentional un- surface. locking your vehicle. Automatic Activation of Immobilizer  For battery, replacement procedure If smart key is not found within the pas- refer ‘MAINTENANCE’ section. senger compartment, engine will be im-  Do not remove the battery connec- mobilized and vehicle cannot start. tion of the vehicle while the vehicle has been locked by remote.

30 OPENING AND CLOSING Two Smart Keys Scenarios SN Scenarios Precondition Action PEPS behavior

One smart key is inside the Lock the vehicle with out- vehicle (away from Immobi- side smart key (passive Vehicle is in OFF lizer antenna) and other lock / RKE lock) and keep When user tries to start the vehicle with 1 mode and all door smart key is outside the vehi- outside smart key away inside smart key, vehicle doesn’t start. closed cle within authentication from authentication range. range.

When user tries to start the vehicle with inside smart key, vehicle would start with back up start. User presses start/stop button twice with the interval One smart key is inside the Lock the vehicle with out- of 2.5 sec between two presses within vehicle (near Immobilizer an- Vehicle is in OFF side smart key and keep 5 seconds. 2 tenna) and other smart key is mode and all door outside smart key away Note: The vehicle doesn’t start if inside outside the vehicle within au- closed. from authentication smart key is kept away from Immobi- thentication range. range. lizer antenna until vehicle is unlocked by outside smart key via outside door handle OR RKE unlock command from inside/outside smart key is received.

31 OPENING AND CLOSING

SN Scenarios Precondition Action PEPS behavior Lock the vehicle with out- One smart key is inside the vehicle (near When user tries to unlock/lock the ve- Vehicle is in side smart key and keep Immobilizer antenna) and other smart hicle ((RKE lock / unlock) with inside 3 OFF mode and outside smart key away key is outside the vehicle within authen- smart key, RKE lock/ unlock opera- all door closed. from authentication tication range. tion takes place normally. range. Lock the vehicle with out- One smart key is inside the vehicle When user tries to start the vehicle Vehicle is in side smart key (passive (away from Immobilizer antenna) and with inside smart key, vehicle doesn’t 4 OFF mode and lock / RKE lock) and then other smart key is outside the vehicle start. However, RKE operations all door closed unlock the vehicle with within authentication range. (lock/unlock) take place normally. mechanical key. When user tries to unlock the vehicle passively with outside One smart key is inside the vehicle Vehicle is in Smart key (from drive), vehicle (away from Immobilizer antenna) and ACC/IGN mode Lock the vehicle with in- 5 doesn’t get unlocked in ACC/IGN other smart key is outside the vehicle and all door ternal knob. mode. Also, when user tries to unlock within authentication range. closed. the Tail gate passively, Tail gate doesn’t get unlocked. Vehicle is in Keep the outside smart One smart key is inside the vehicle ACC/IGN key within driver door vi- (away from Immobilizer antenna) and mode, all door cinity and try to lock ve- Vehicle doesn’t get locked in ACC / 6 other. Smart key is outside the vehicle closed, and vehicle with driver door IGN mode. within authentication range. hicle is in un- handle switch from driver lock state. side. 32 OPENING AND CLOSING Doors Option 2 Horn Honking when Door Locking using Door Handle Switch (DHS) Option 1 Door Locking / Unlocking using If vehicle is in unlock condition and Door Locking / Unlocking with Key Door Handle Switch (DHS) smart key is not available, (i.e. Smart Driver / front passenger doors can be To lock/unlock all the doors without op- Key is present away from authentication locked or unlocked from outside using erating smart key button/ key blade. range) and if you tries to lock the vehicle the key blade. Press the door handle switch (DHS) pro- through door handle switch then vehicle vided on the driver door to lock/unlock horn honking gets activated for 9 sec. all the four doors except tailgate. If vehicle is in unlock condition and Smart key is present inside the vehicle. If you tries to press the door handle switch then vehicle horn honking gets activated for 9 sec.

NOTE  Authentication range for smart key shall be 1 to 1.5 meter from outside the respective door or Tail gate. Insert the key and turn it clockwise to lock and anticlockwise to unlock the  Passive entry only works during ignition off. door.

33 OPENING AND CLOSING Locking without a Key from Inside Unlocking the Doors from Inside Windows Power Windows (if available)

All the doors can also be locked from in- 1. Door opening knob side by pressing knob on driver door and Door opening Lever independently on other doors respec- 2. 1. Front Window Winding Switch (Right) tively. All doors can be opened from inside. To 2. Front Window Winding Switch (Left) open, pull the door opening knob (1) and 3. Rear Window Winding Switch (Right) then opening lever (2). 4. Rear Window Winding Switch (Left) NOTE 5. Inhibit Switch There is a single pull override fea- Window glasses on all four doors can be ture on driver door. All door can be operated by switches provided on the unlocked by inner handle without main control panel located on the operating lock knob of inner han- driver’s arm rest. They work only when dle. the key is in the ‘IGN ON’ position.

34 OPENING AND CLOSING

NOTE The Anti-pinch module is provided. It will stop window upward movement if any Power windows can be operated obstruction or resistance detected. for 30 sec. in ‘IGN OFF’ and ‘KEY OUT’ position, provided doors are Thus, it gives full and reliable protection Glasses are wound up by pulling the not open. for hand, neck and any obstacles as switch and are lowered by pressing. well. Anti-pinch function is provided for Express Down (if available) driver door only. WARNING Window glasses can be opened by a sin- Individual Switches While raising the glass, take care gle long press of the switch. Express to avoid fingers/hands getting down feature is provided for driver door Individual window winding switches trapped between glass and the only. have been provided for front passenger door frame. and rear passengers. Anti-pinch Function (if available)

35 OPENING AND CLOSING Inhibit Switch (if available) Inhibit Switch OFF Bonnet Opening When switch is 1. Ensure that the vehicle is in neutral pressed, red light gear with the parking brake applied. turns ‘ON’. The indi- 2. Pull the bonnet release lever. The vidual switches pro- bonnet will pop up slightly. vided on rear and front passenger door can be operated. It can also be operated from the switches on driver's arm rest.

WARNING  If children operate the windows they could be get trapped, partic- Inhibit Switch ON ularly if they are left unsuper- When switch is vised. There is a risk of injury. pressed, red light  Activate the window inhibit fea- turns ‘OFF’. The indi- ture when children are travelling. vidual switches pro- While leaving the vehicle, always 3. Raise the bonnet slightly and with vided on rear and take the key with you and lock your finger lift (up) the secondary front passenger door cannot be oper- the vehicle. Never leave children lock lever located under the bonnet ated. Still it can be operated from the unsupervised in the vehicle. center.

switches on driver's arm rest.

36 OPENING AND CLOSING Engine Bonnet Stay rod Closing 1. To close the bonnet, hold the bonnet by one hand, disengage the stay rod and clamp it back properly. 2. Lower the bonnet close to the bumper, then let it drop down.

WARNING Ensure that the bonnet is properly locked before driving or it can fly up

unexpectedly during driving. NOTE Make sure that the wiper arms are not raised before you lift up the WARNING bonnet to avoid damaging the  The stay rod can be hot enough wiper arms and the bonnet. to burn your finger right after

4. Lift the bonnet up. Pull the bonnet driving. To avoid this, use rubber stay rod from its clip and insert the packing given on stay rod. free end into the slot provided on  Touch the rod after it becomes frame. cool enough.  Insert the stay rod into the hole securely. If the rod drops off, your body may be caught below the bonnet.

37 OPENING AND CLOSING Tail Gate Opening (as available) Option II Option III

NOTE Some variants may have multiple options.

Option I

When user press the Tail gate button on If vehicle is locked and tail gate is remote, Tail gate gets unlatched. closed. Tail gate switch is pressed with valid smart key in the authentication range, Tail gate gets unlatched.

On closing the tail gate door, Tail gates gets locked. Remote operated Tail gate unlatching can be done through long press (2 sec) approach light button on remote key.

38 OPENING AND CLOSING

NOTE Option IV 4. And access the tailgate-opening lever from inside.  During closing Tail gate if doors Emergency Tailgate Opening are in locked condition and valid 5. Turn the lever clockwise to unlatch smart key is inside the trunk, and open the tailgate. then Tail gate can be unlocked by pressing tailgate switch. NOTE This can be used in emergency  For Tail gate unlatch remote op- when you are inside the vehicle. eration, vehicle shall be in OFF mode.  Tail gate once unlatch it will not get locked automatically with other doors.  If doors are in unlocked condition, Tail gate can be unlocked via Tail gate handle switch inde- In emergency situation like key or vehi- pendent of smart key. cle battery is discharged or electrical  Avoid keeping smart key inside malfunctioning, you can unlock the tail- the boot space area while clos- gate from inside as per procedure given ing Tail gate. below:

1. Open driver door using mechanical WARNING key. Tail gate can’t be locked using mechanical key/ flip key/ smart key. It 2. Open the rear door. can be locked by slamming it. 3. Fold the rear seat. 39 OPENING AND CLOSING Fuel Lid  Do not continue adding fuel after the automatic shut ‘OFF’ func- 1. To open the fuel flap, gently press on tion is operated if it is equipped fuel flap. Make sure the smart key on the fuel station. Overfilling the should be in authentication range fuel tank could damage the fuel and the vehicle is in unlock condi- system.

tion. NOTE NOTE For mechanical/flip key (without  Remove the fuel filler cap slowly, smart key), to open the fuel flap. and wait for any hissing to stop. Make sure that vehicle is in unlock The fuel may be under pressure condition. Then gently press the and may spray out. fuel flap. 3. To open the fuel cap by turning it in  When smart key is inside the car, 2. Open the fuel flap by gently pressing counter clockwise for fuel filling. fuel flap can be open by pressing flap. 4. For closing, close the fuel cap and the flap. gently push the fuel flap till it gets locked. If fuel cap needs replacement, ensure that it is replaced by a genuine cap at the WARNING TATA MOTORS Authorized Service Centre  Fuel vapour is extremely hazard- only. ous. Always switch ‘OFF’ the engine before refueling and never refill near sparks or open flames. Do not use cell phone while refueling.

40 OPENING AND CLOSING Power Sunroof (if available) 1. Location of Controls and their To operate the sliding sunroof and Rollo functions shade. Push the switch as shown in above fig. after every operation switch goes to Home position automatically.

WARNING You must switch on the ignition to operate the power sunroof. After switching off the ignition, You can still open or close the power sunroof for 3 minutes as long as the driver or front passenger door has not been opened.

A Sunroof will make the driving expe- Power Sunroof Switches rience more enjoyable by bringing 1 — Sunroof Open light and sunshine into the vehicle. It 2 — Sunroof Close provides a real open air feeling along 3 — Tilt Up with pure driving fun. With fresh air, your driving experience automati- 4 — Tilt Down cally becomes significantly more re- 5 — Sunshade Open laxed. 6 — Sunshade Close A sunroof allows air to flow evenly from above the driver, which is much quieter and less intrusive than wind blowing through a side window.

41 OPENING AND CLOSING 2. Sunshade Open Position Manual (long press) open and stop at desired position. 3. Sunshade Close Position

Push the switch (6) to close the Sun- shade. Express (one touch) close to close Sun- shade completely. Manual (long press) Close and stop at desired position.

Push the switch (5) to open the Sun- shade. Express (one touch) open to open Sun- shade completely.

42 OPENING AND CLOSING

4. Sunroof Open Position NOTE 6. Sunroof Tilt Open/Close Posi- During sliding sunroof Express (one tion touch) open operation, Sunshade will also open in synchronization with sliding sunroof (Express Complete Open Feature).

5. Sunroof Close Position

Push the switch (3) for Sunroof Tilt Open. Push the switch (4) for Sunroof Tilt Close. Express (one touch) Tilt Open / Close sunroof completely. Manual (long press) Tilt Open / Close and stop at desired position.

Push the switch (1) to open the Sunroof. Express (one touch) open to open Sun- Push the switch (2) to close the Sunroof. roof completely. Express (one touch) close to close sun- Manual (long press) open and stop at de- roof completely. sired position. Manual (long press) close and stop at

desired position. 43 OPENING AND CLOSING

Auto Sunroof Close WARNING Follow the emergency close command as below: Sliding Sunroof will automatically close  Without pinch protection, the under following conditions: power sunroof will close with Emergency close feature can be used, if enough force to cause serious Sliding sunroof or Sunshade consecu-  Rain detection- As soon as rain de- personal injury. tive reversal movement observed 3 tected & Wiper speed is slow/high  Always be careful when closing times within 10 sec then follow the steps based on Rain, the Sunroof will the power sunroof. given below: close.  Pinch protection cannot prevent  Ignition off and driver came out of 1. On the 4th attempt continuously fingers or other parts of the body the vehicle by carrying the Remote press the sunroof close switch - posi- from being pressed against the key and driver locking the vehicle tion (2) or Sunshade close switch - edge of the roof; may result in in- through remotely or through driver position (6) until it closes completely juries. door. to ensure occupant privacy, safety & theft prevention from Sunroof open Emergency Close Feature NOTE window. This is Emergency Close If the power sunroof malfunctions, If Express (One Touch) / Manual (long Feature. press) Sunroof and Sunshade close pinch protection may not function WARNING properly. Visit an authorized TATA function did not work due to: Motors dealer or an authorized  Consecutive several attempts to Never keep your hands or head in TATA Motors Service Facility for as- Open / close Sunroof and Sun- the Sunroof window while perform- sistance. shade. ing this operation it may cause severe injury, since Anti-pinch func-  Excessive Ice / Dirt accumulation tion will not work at this 4th at- on the Sunroof Glass / guiderails. tempt.

44 OPENING AND CLOSING 2. Once the sunroof or Sunshade is Initializing the power sunroof clicking sound comes from Sun- completely closed, release the shade. switch. Condition for initializing the sunroof 4. The Initializing command is com- 3. Alternatively, User may wait for min. If the vehicle battery is disconnected and plete, Check if the Express 30 secs before operating Sunroof reconnected during Sunroof / Sunshade open/close features are working. and Sunshade, then Sunroof can be movement or while replacing the dead operated with Normal Functions. fuse, the sunroof/ Sunshade must be in- NOTE itialized. NOTE If the initializing procedure is not completely performed, then it has Otherwise Express (one touch) function If the Sunroof doesn’t operate as to be run again from step 2. above, Visit an authorized TATA (open/close/tilt) and pinch protection Motors dealer or an authorized function will be deactivated. Self-learning procedure of Sunroof TATA Motors Service Facility for as- Initializing command procedure:  Sliding sunroof and Sunshade shall sistance. be in open position within 4 mm to To initialize the sliding sunroof and Sun- 200 mm from the cutout.

shade, use the following procedure:  Close the sunroof fully by pressing 1. Turn ON the ignition. ‘sunroof close switch’ and keep the 2. Close the sunroof fully by pressing switch pressed continuously. Do not ‘sunroof close switch’ and keep the release the switch and wait for fol- switch pressed for 1-2 seconds after lowing actions to perform. the roof is fully closed, till clicking  Sliding sunroof will start opening af- sound comes from Sunroof. ter 5 sec pause and close automati- 3. Close the Sunshade fully by pressing cally. Release the Switch to com- ‘Sunshade close switch’ and keep plete the procedure. the switch pressed for 1-2 seconds  Close the sunshade fully by pressing after the Sunshade is fully closed, till ‘Sunshade close switch’ and keep

45 OPENING AND CLOSING the switch pressed continuously. Do before opening or tilting it in win-  Always close the sunroof while not release the switch and wait for ter season. washing the vehicle. following actions to perform.  Always close the sunroof before  Sunshade will start opening after 5 leaving the vehicle or if it begins WARNING sec pause and close automatically. to rain. If the sunroof is open or Improper use of the power sunroof Release the Switch to complete the tilted, rain could enter the vehi- can result in serious personal injury. procedure. cle interior and cause extensive  Always make sure that no one is  The self-learning command is com- damage to the electrical system. in the Path/Cutout of the power plete. This could result in further vehi- sunroof when it is Closing OR cle damage. Opening NOTE  Remove leaves and other ob-  Always take the key with you while jects from the sunroof guiderails Incase Sunroof and Sunshade leaving the vehicle. Close switch is released in the mid- regularly either by hand or using  Never leave children or disabled dle of procedure, repeat from step a vacuum cleaner. persons in the vehicle particu-  If the power sunroof malfunc- 1. larly, if they have access to the ve- tions, pinch protection may not hicle key. Unsupervised use of the function properly. See an author- NOTE remote control vehicle key makes ized TATA Motors dealer or an it possible to lock the vehicle,  You can still open or close the authorized TATA Motors Service start the engine, turn on the igni- power sunroof for 3 minutes af- Facility. tion and operate the sunroof. ter you switch off the ignition, as  The Sunshade can be opened long as the driver or front pas- and closed independently when senger door has not been the sliding sunroof is in closed opened. position but will not operate in  To help prevent damage, remove case sliding sunroof is open or in ice and snow from the sunroof tilt position.

46 DASHBOARD AND FEATURES

Cockpit 1 A.C. Air vent 2 Airbag (PAB) 3 Infotainment Display (if available) 4 Combi-Switch 5 Horn pad 6 Start/Stop switch (if available) 7 Airbag (DAB) 8 Steering Wheel Switches (if available) 9 Controls 10 Foot Rest 11 Terrain Response Knob (if available) 12 Cooled storage box 13 Parking Brake Lever 14 Gear Shift Lever 15 USB/AUX Port 16 HVAC Control panel 17 Fascia switches NOTE: All location shown may not be applicable to your vehicle / Variants. 18 Center Air Vent 19 Glove Box

47 DASHBOARD AND FEATURES Instrument Cluster ( TFT Screen) Tachometer Driver Information Display Speedometer

DEF Gauge Temperature Gauge Fuel Gauge

NOTE: All indicators shown may not be applicable to your vehicle.

48 DASHBOARD AND FEATURES Speedometer Tachometer Fuel Gauge When the ignition switch is in “ON” position, fuel gauge gives an approximate indication of the amount of fuel in the fuel tank. In indication window, “F” stands for full and “E” stands for empty.

Speedometer indicates the vehicle Tachometer indicates engine speed in speed in km/h. revolutions per min (rpm). NOTE WARNING Whenever you turn the ignition ON, Never drive the vehicle with high the instrument cluster needles and engine rpm. This may cause severe gauges move to maximum value When fuel in the tank is near to empty engine damage. and return to '0' position. This is a position, low fuel warning telltale turns welcome strategy and a self-check Amber. Refill the tank as soon as possi- feature. ble.

49 DASHBOARD AND FEATURES

NOTE Temperature Gauge WARNING  Check the fuel level when the ve- When the ignition switch is in the “ON” The red progress bar on high cool- hicle is stationary on a level road. position, this gauge indicates the engine ant temperature indicates over-  The fuel level displayed can vary coolant temperature. heating that may damage the en- when you drive on inclines, gine. Continuing to drive the vehi- curves, brake and accelerate cle when engine overheating is in- suddenly. This is due to the dicated can result in severe engine movement of fuel in the tank. The indicator should be within the nor- damage or fire. The low fuel warning lamp may mal, acceptable temperature range i.e. DEF Gauge turn to ON or OFF earlier or later between “H” and “C”. If the indicator ap- than usual. proaches “H”, overheating is indicated When the ignition switch is in the “ON”

by red progress bar. position, arrow in the gauge indicates level of DEF left in the tank. WARNING If the coolant temperature is very high, If there is any fault in the system, the engine coolant temperature telltale the low fuel warning symbol will flashes with an audio warning. In this blink. Take your vehicle to the near- case, stop the vehicle, switch ‘OFF’ the est TATA MOTORS Authorized ser- engine and allow it to cool down for vice centre.. some time. Contact the nearest TATA The Indicator should be within the ac- MOTORS authorized service centre im- ceptable range. i.e., between "E" and "F". mediately for rectification. When DEF in tank is near to empty position, DEF tell tale near to gauge will glow with subsequent Text alert on DIS Screen. If DEF level reaches to critically

50 DASHBOARD AND FEATURES low level, then DEF Gauge will be re- NOTE placed by the permanent text alert along with buzzer.  Check the DEF Level when the vehicle is on level road. Similarly for Low DEF Quality & SCR Fault  DEF Level Displayed may vary there are featured text and warnings present to alert the driver regarding condi- when you drive on inclines, de- tion of DEF System. clines, curves, brakes & accelerate suddenly. This is due to the WARNING movement of DEF in the tank.  If DEF Level or DEF Quality or SCR  If SCR Fault issue comes the take Fault becomes Critical after suffi- your vehicle to the nearest TATA MOTORS Authorized service cen- cient alerts, warnings, Buzzers & ter. If not rectified then Text alert will be displayed permanently on DIC Screen stating vehicle will not re-

start in next key ON & Vehicle will not start.

 If any problem comes then, Take your vehicle to the nearest TATA MOTORS Authorized service center.

51 DASHBOARD AND FEATURES Driver Information System

Driver Information System Image Description Indicates distance travelled by a vehicle. The odometer reading does not Odometer return to “0” when maximum value is reached, the display will freeze to maximum value.

The trip meter can be used to measure the distance travelled on short trips

Trip meter A & B or between fuel stops. It can be reset to “0”. The Trip meter reading becomes “0.0” after it crosses 9999.9 km.

Indicates current time in AM/PM mode. Whenever the battery terminals or related fuses are connected, you must reset the clock time. This feature is available when ignition switch is in Clock

‘ON’’ position. NOTE: Clock settings can also be changed through infotainment system. For more information, refer infotainment manual.

Indicates the value of Power and Torque delivered by engine in the particular Power and Torque driving condition.

52 DASHBOARD AND FEATURES

Driver Information System Image Description Indicates the number of days/kilometers in which service is due. If service is overdue, it will display “0” km or “0” days and spanner symbol will blink at every ignition ON for few seconds. Never reset the display between service intervals otherwise this may result in to incorrect readings. Information is re- Service reminder tained in the service interval display even after the vehicle battery is disconnected. NOTE: This option is for indicative purpose only. Keep track of your odometer reading and follow the maintenance schedule.

Respective door open display pop up comes up for sec and then minimize Door Ajar 5 telltale glows with respective door open will displayed.

Current gear engaged by the transmission shall be displayed on DIS. Current gear position NOTE: If “Fault” is displayed it means a ‘Fault’ condition. Contact the TATA (indicator) (for MT & AT- MOTORS authorized service centre. Manual Mode) In case of Manual Transmission, the gear number shall be displayed when the clutch is fully released.

53 DASHBOARD AND FEATURES

Driver Information System Image Description

Current gear engaged by the transmission shall be displayed on DIS. NOTE: If “Fault” is displayed it means ‘Fault’ condition. Contact the TATA Current gear position MOTORS Authorised Service Centre. (indicator) (for AT) In case of Automatic Transmission, the gear type P-Park, D-Drive, N-Neutral and R-Reverse will be displayed as per automatic gear selected.

Up or down arrow shall be displayed on DIS whenever a gear should be shifted Gear Recommendation up or down. (for MT) No arrow shall be displayed when the selected gear is as per the vehicle dynamics. This message displayed when gear shift is denied in manual mode. Driver Control Shift Denied User has to drive the vehicle in recommended speed to change the gear.

Electronic Brake Distribution (EBD) System Fault Electronic Brake Distribution Fault User has to take the vehicle to Authorized Tata motors service station.

54 DASHBOARD AND FEATURES

Driver Information System Image Description This message displayed when transmission oil temperature is higher than al- Transmission Oil lowable limit. Temperature High User has to take the vehicle to Authorized Tata motors service station. Transmission Failure This message displayed when transmission related failure is present. Drive Cautiously Visit User has to take the vehicle to Authorized Tata motors service station. Service Centre Transmission failure This message displayed when transmission related failure is present. Malfunction detected User has to take the vehicle to Authorized Tata Motors service station. contact service center

Shift to Park to Exit This message displayed when shift lever not in P (park) mode.

Shift to Park or Neutral This message displayed when shift lever not in P (park) or N (neutral) mode to start the Engine while starting the engine.

55 DASHBOARD AND FEATURES

1. Instantaneous Fuel Economy NOTE 3. Average Fuel Economy (AFE) (IFE)  IFE will vary frequently as per driving pattern.  IFE display does not show Fuel Economy of last drive.

2. Power and Torque

Trip A

It indicates fuel economy of current drive when Ignition is turned ‘ON’. To reach the Instant Fuel Economy in the Instrument cluster. Press the switch, which is on the RHS steering Indicates the amount of power and switch. torque delivered by engine in the partic-

The display does not show actual value ular driving condition. Trip B unless vehicle is moving. AFE value is estimate of fuel economy. It may vary significantly based upon driving conditions, driving habits and condition of the vehicle.

56 DASHBOARD AND FEATURES

To see the Average fuel economy in the 4. Distance to Empty (DTE) NOTE Instrument cluster. Press the  If DTE is displayed as ‘---‘, then switch on the RHS of the steering switch. take your vehicle to the TATA Trip time, Average speed and Trip dis- MOTORS Authorized Service tance will reset to ‘0’ when respective Centre. Trip meter is reset.  The DTE will update with new NOTE value when fuel is added for  Average Fuel Economy, Trip more than 7 Litres at a time. time and Average speed will get 5. Infotainment Information on In- reset to ‘0’ when Battery is re- strument Cluster Display unit. moved and refitted. The above DTE screen indicates approx-  Average Fuel Economy will be imate distance in ‘km’ that your vehicle displayed as ‘--.--‘for initial 0.5 can travel with available fuel in the tank. km of respective trip. Once 0.5 To reach the Distance to empty in the In- km distance is covered, Average strument cluster. Press the Fuel Economy will be displayed. switch, which is on RHS steering switch. The Instrument Cluster will display the  Even after 0.5 km distance covered for particular trip, if Aver- DTE values may vary significantly based Infotainment information like Media, age Fuel Economy is displayed on driving conditions, driving habits, and Navigation and FM. as ‘--.--‘, then take your vehicle to condition of the vehicle. It is an estimate TATA MOTORS Authorized Ser- value of the available driving distance. vice Centre. If low fuel warning light turns ‘ON’, fill the fuel tank immediately regardless the

value of displayed DTE.

57 DASHBOARD AND FEATURES 6. Setting Screen Following options are displayed in the Illumination Screen setting screen: You can select illumination setting by scroll down using up or down on the RHS steering switch and by pressing select button. You can increase the Illumination from (20% to100%) in 5 steps by pressing on the RHS of steering switch. Following screen gets displayed: You can enter into setting screen by pressing select button while To change the option from unit to service being in setting screen. reminder reset by pressing on the RHS of steering switch.

58 DASHBOARD AND FEATURES Service Reminder Reset About Screen 7. Outside Ambient Temperature You can select Service reminder reset You can select about option by scroll up screen by scroll down & pressing set but- or down and pressing set ton in settings screen. button on RHS steering switches. It displays open source license disclosure. You can select Yes or No option by up or down arrows & set button.

This displays outside ambient temperature in units of °C with the resolution of 1 °C. NOTE NOTE Pressing select button while in The temperature sensor is located on about screen, the screen will be the front bumper of the vehicle, there- In setting menu if there is no user close and goes to previous screen. fore the temperature reading can be af- input for 10 sec, previous screen fected by heat reflection from the road shall be displayed. surface, engine heat and the exhaust from surrounding traffic.

59 DASHBOARD AND FEATURES

NOTE

For an accurate temperature reading, make sure the vehicle speed is above 30 kmph.

WARNING

If display shows OAT temp as “- - “, take your car to a TATA authorized service Centre.

60 DASHBOARD AND FEATURES

Display Messages on Instrument Cluster Below messages can be displayed in the screen for 3 sec based on the priority. 1. Warning Messages (messages displayed within the Red border)

NOTE: All messages may not be applicable to your vehicle SN Warning / Information Title Warning Message Title Warning Messages on Instrument Cluster

1 Fasten Seat Belt - Driver Seat Belt Reminder Fasten Driver Seat Belt 2 Speed Limit Warning Speed Limit Warning Over Speeding Detected Slow Down

61 DASHBOARD AND FEATURES

SN Warning / Information Title Warning Message Title Warning Messages on Instrument Cluster Transmission Failure Drive Cau- Transmission Malfunction Drive Cautiously Contact Service Center 3 tiously Visit Service Center 4 Drive Control Shift Denied Drive Mode Warning Drive Control Shift Denied 5 Hill Hold Control Failure Hill Hold Control Malfunction Detected Contact Service Center 6 Hill Decent Control Failure Hill Decent Control Malfunction Detected Contact Service Center 7 Fuel Level Low State Fuel Level Warning Fuel Level Low 8 Fasten seat belt front passenger Seat Belt Reminder Fasten Front passenger Seat Belt Transmission Failure Limp home Ac- Transmission System Malfunction Detected Contact Service Center 9 tivated Visit Service Center 10 DEF level warning 1 DEF Level Low DEF Level Low Refill Soon Engine Stops in “Value” Km 11 DEF level warning 2 DEF Level Low Refill DEF Engine Stops in “Value” Km 12 DEF level warning 3 DEF Level Low Refill DEF Engine Stops in “Value” Km 13 DEF level warning 4 DEF Level Low Refill DEF

62 DASHBOARD AND FEATURES

SN Warning / Information Title Warning Message Title Warning Messages on Instrument Cluster Engine Stops in “Value” Km 14 DEF level warning 5 DEF Level Low Refill DEF 15 DEF level warning 6 DEF Level Low Engine Will Not Restart In Next Key On Engine Stop 16 DEF level warning 7 DEF Level Low DEF Tank Empty DEF Quality Low 17 DEF quality warning 1 DEF Quality Low Check DEF System Engine Stops in “Value” Km 18 DEF quality warning 2 DEF Quality Low Check DEF System Engine Stops in “Value” Km 19 DEF quality warning 3 DEF Quality Low Check DEF System Engine Stops in “Value” Km 20 DEF quality warning 4 DEF Quality Low Check DEF System Engine Stops in “Value” Km 21 DEF quality warning 5 DEF Quality Low Check DEF System 22 DEF quality warning 6 DEF Quality Low Engine Will Not Restart In Next Key On Engine Stop 23 DEF quality warning 7 DEF Quality Low Check DEF System SCR System Fault 24 DEF fault warning 1 SCR System Fault Contact Service Centre

63 DASHBOARD AND FEATURES

SN Warning / Information Title Warning Message Title Warning Messages on Instrument Cluster Engine Stops in “Value” Km 25 DEF fault warning 2 DEF System Fault Contact Service Centre Engine Stops in “Value” Km 26 DEF fault warning 3 DEF System Fault Contact Service Centre Engine Stops in “Value” Km 27 DEF fault warning 4 DEF System Fault Contact Service Centre Engine Stops in “Value” Km 28 DEF fault warning 5 DEF System Fault Contact Service Centre 29 DEF fault warning 6 DEF System Fault Engine Will Not Restart In Next Key On Engine Stop 30 DEF fault warning 7 DEF System Fault Contact Service Centre

64 DASHBOARD AND FEATURES 2. Alert Messages (messages displayed within Grey border)

NOTE: All messages may not be applicable to your vehicle.

SN Alert / Information Title Alert Message Title Action to be taken HDC Deactivation Due To Speed Hill Decent Control System Deactivated Speed Crossed Set Limit 1 Above Set Value 2 Park Brake Engaged Brake Alert Park Brake Engaged 3 Electronic Stability Off Electronic Stability System ESP Turned Off 4 Traction Control Off Traction Control System TCS Turned Off 5 Gear shift denied Transmission alert Drive shift denied

65 DASHBOARD AND FEATURES

SN Alert / Information Title Alert Message Title Action to be taken Shift to Park to Vehicle Off func- Transmission alert Shift to Park (P) to Exit 6 tion on AT Vehicle 7 Hill Descent Control Active Hill Descent Control HDC Activated 8 Auto Headlamp Lamp Alert Auto Headlamp Activated Resume to Target Speed Not Pos- Cruise Control Shift to higher gear to resume Cruise Speed 9 sible in Current Gear 10 Cruise Override Cruise Control Cruise Override 11 Hill Descent Control Switched On Hill Descent Control HDC Turned ON Shift to Park (P/N) - vehicle Start Transmission Alert Shift to Park or Neutral to Start Engine 12 function for AT vehicle

66 DASHBOARD AND FEATURES 3. Interrupt Messages

NOTE: All messages may not be applicable to your vehicle.

SN Alert / Information Title Action to be taken 1 Rotate steering wheel (In ESCL jam condition) Press Start Button while Turning Wheel 2 Smart key out of range Smart Key Out of Range 3 Drive Alert - Tea Break Take a Break 4 Steering Failure-Visit Garage Steering Failure Contact Service Center 5 Steering Failure-Stop Driving Steering Failure Stop the Vehicle Safely 6 Door Ajar Door open

67 DASHBOARD AND FEATURES

SN Alert / Information Title Action to be taken 7 Combination alerts Check Tires 8 Air Leak Leakage Detected Check Tires 9 ESCL Press Start Button While Turning Wheel 10 No Key Smart Key Out of Range 11 Low Key Battery Smart Key Battery Low Replace Battery 12 Press Clutch Pedal Press Clutch Pedal to Start Engine 13 Press Brake Pedal Press Brake Pedal to Start Engine 14 Drive Modes Respective drive mode 15 Tea Break Take a Break

68 DASHBOARD AND FEATURES Instrument Cluster (LCD Screen) Tachometer Driver Information Display Fuel Gauge Speedometer

Set knob Temperature Gauge Mode knob

NOTE: All indicators shown may not be applicable to your vehicle

69 DASHBOARD AND FEATURES Speedometer Tachometer Fuel Gauge When the ignition switch is in “ON” position, fuel gauge gives an approximate indication of the amount of fuel in the fuel tank. “F” stands for full and “E” stands for empty.

When fuel in the tank is near to empty Speedometer indicates the vehicle Tachometer indicates engine speed in position, low fuel warning telltale turns speed in km/h. revolutions per min (rpm). Amber. Refill the tank as soon as possible. NOTE WARNING Whenever you turn the ignition ON, Never drive the vehicle with high the instrument cluster needles and engine ‘rpm’. This may cause se- gauges move to maximum value vere engine damage. and return to '0' position. This is a welcome strategy and a self-check feature.

70 DASHBOARD AND FEATURES

NOTE Temperature Gauge WARNING  Check the fuel level when the ve- When the ignition switch is in the “ON” The Red bar on high coolant tem- hicle on a level road. position, this gauge indicates the engine perature warning indicates over-  The fuel level displayed can vary coolant temperature. heating that may damage the en- when you drive on inclines, gine. Continuing to drive the vehi- curves, brake and accelerate cle when engine overheating is in- suddenly. This is due to the dicated can result in severe engine movement of fuel in the tank. damage or fire. The low fuel warning lamp may IFE Gauge turn to ON or OFF earlier or later The indicator should stay within the nor- than usual. mal, acceptable temperature range between “H” and “C”. If the indicator ap- WARNING proaches “H”, overheating is indicated

If there is any fault in the system, by a red bar. It indicates fuel economy of current drive the low fuel warning symbol will If the coolant temperature reading is when Ignition is turned ‘ON’. start blinking. Take your vehicle to very high, the engine coolant tempera- the nearest TATA MOTORS author- ture telltale flashes with an audible To reach the Instant Fuel Economy in the ized service centre. buzzer. In this case, stop the vehicle, Instrument cluster. Press the SET and switch ‘OFF’ the engine and cool it down MODE button. for some time. Contact the nearest TATA The display does not show actual value MOTORS Authorised Service Centre im- unless vehicle is moving. mediately for rectification.

71 DASHBOARD AND FEATURES

NOTE Similarly for Low DEF Quality & SCR Fault NOTE there are featured text and warnings pre-  IFE will vary frequently as per sent to alert the driver regarding condi-  Check the DEF Level when the ve- driving pattern. tion of DEF System. hicle is on level road.  IFE display does not show Fuel  DEF Level Displayed may vary Economy of last drive. WARNING when you drive on inclines, de- clines, curves, brakes & acceler- DEF Gauge  If DEF Level or DEF Quality or SCR Fault becomes critical after de- ate suddenly. This is due to the When the ignition switch is in the “ON” fined interval of warnings text movement of DEF in the tank. position, this gauge indicates level of alert will be displayed perma-  If SCR Fault issue comes the take urea left in the tank. nently on LCD screen stating vehi- your vehicle to the nearest TATA cle will not restart in next key ON. MOTORS Authorized service cen-  On getting defined text messages ter. related to Quality and SCR Fault,  IFE gauge and DEF Gauge can be take your vehicle to the nearest rollover each other with all combi- TATA MOTORS Authorized service nations when DEF level in vehicle center. is not critical. The Indicator should be within the acceptable range. i.e., between "E" and "F".

When DEF in tank is near to empty position, DEF tell tale near to gauge will glow with subsequent text messages on LCD screen. If DEF level reaches to critically low level, only DEF gauge will be displayed.

72 DASHBOARD AND FEATURES Driver Information System

Driver Information System Image Description Indicates distance travelled by a vehicle. The Odometer reading does not Odometer return to “0” when maximum value is reached, the display will freeze to maximum value.

The trip meter can be used to measure the distance travelled on short trips Trip meter A & B or between fuel stops. It can be reset to “0”. The Trip meter reading becomes “0.0” after it crosses 9999.9 km.

Indicates current time in AM/PM mode. Clock time can be changed using ‘SET’ & ‘MODE’ knob. Whenever the battery terminals or related fuses are connected, you must

Clock reset the clock time. This feature is available when ignition switch is in ON’ position. NOTE: Clock settings can also be changed through infotainment system. For more information, refer infotainment manual.

This warning will be indicated when driver door is open. Door Ajar NOTE: If any other door is open, the roof lamp will be ‘ON’.

73 DASHBOARD AND FEATURES

Driver Information System Image Description Indicates the number of days/kilometers in which service is due. If service is overdue, it will display “0” km or “0” days and spanner symbol will blink at every ignition ON for few seconds. Never reset the display between service intervals otherwise this may result in to incorrect readings. Infor- Service reminder mation is retained in the service interval display even after the vehicle battery is disconnected. NOTE: This option is for indicative purpose only. Keep track of your odometer reading and follow the maintenance schedule.

Current gear engaged by the transmission shall be displayed on Driver In- formation System. Current gear position indica- NOTE: If “F” is displayed it means a ‘Fault’ condition. Contact the TATA tor (For MT) MOTORS authorized service centre. In case of Manual Transmission, the gear number shall be displayed when the clutch is fully released.

Up or down arrow shall be displayed on DIS whenever a gear should be shifted up or down. Gear Recommendation No arrow shall be displayed when the selected gear is as per the vehicle dynamics.

74 DASHBOARD AND FEATURES

Driver Information System Image Description

-Park Current gear engaged by the transmission shall be displayed on DIS. NOTE: If “F” is displayed it means ‘Fault’ condition. Contact the TATA Current gear position indica- -Reverse tor (For AT) MOTORS Authorised Service Centre. In case of Automatic Transmission, the Gear numbers shall be dis- -Neutral played as per automatic gear selected.

-Drive

75 DASHBOARD AND FEATURES

1. Average Fuel Economy (AFE) NOTE If low fuel warning light turns ‘ON’, fill the fuel tank immediately regardless the  AFE value is an estimate of fuel value of displayed DTE. economy. It may vary significantly based upon driving condi- NOTE tions, driving habits and condi- If DTE is displayed as ‘---‘, then take tion of vehicle. your vehicle to the TATA MOTORS  Average Fuel Consumption will authorized service centre. get Reset to ‘0’ when Battery is Trip time, Average speed and Trip dis- removed and refitted. 3. Instrument Cluster Illumination tance will reset to ‘0’ when respective Trip meter is reset. 2. Distance to Empty (DTE) Average Fuel Economy will be displayed as ‘--.--‘for initial 0.5 km of respective trip. Once 0.5 km distance is covered, Av- erage Fuel Economy will be displayed. The above image indicates an approxi- Even after 0.5 km distance covered for mate distance in ‘km’ that your vehicle particular trip, if Average fuel economy is can travel with available fuel in tank. displayed as ‘--.--‘, then take your vehicle DTE values may vary significantly based to TATA MOTORS Authorized Service on driving conditions, driving habits, and Centre. condition of the vehicle. It is an estimate value of the available driving distance. Instrument cluster illumination & back- The DTE will update with new value when light illumination will turn on after Park fuel is added more than 7 litres at a time. lamp is ON.

76 DASHBOARD AND FEATURES Illumination can be changed by SET button short press (less than 1.5 seconds).

WARNING The clock and instrument cluster illumination settings should be changed only when the vehicle is in stationary condition for safety pur- poses.

4. Outside Ambient Temperature

This displays outside ambient temperature in units of °C with the resolution of 1 °C. The temperature sensor is located on the front bumper of the vehicle, therefore the temperature reading can be affected by heat reflection from the road surface, engine heat and the exhaust from surrounding traffic.

77 DASHBOARD AND FEATURES

Display Messages on Instrument Cluster Warning Messages on SN Warning Title/ Title Instrument Cluster 1 Speed Limit Warning OVER SPEED HDC Deactivation Due To HDC DEACTIVE 2 Speed Above Set Value 3 Engine Is Locked ENGINE LOCKED 4 Low Brake Fluid LOW BRAKE FLUID 5 Electronic Stability Off ESP OFF 6 Hill Decent Control Active HDC ACTIVE 7 Service Reminder Days SERVICE DUE 8 Service Reminder Kms SERVICE DUE 9 Fuel Level Low State LOW FUEL 10 Drive Alert1 - Tea Break TAKE A BREAK 11 Smart key out of range KEY OUT OF RANGE Rotate steering wheel (In ROTATE STEERING 12 ESCL jam condition)

Resume to Target Speed 13 Not Possible in Current UNABLE TO RESUME Gear

NOTE: All messages may not be applicable to your vehicle.

78 DASHBOARD AND FEATURES

Warning Messages on Warning Messages on SN Warning Title/ Title SN Warning Title/ Title Instrument Cluster Instrument Cluster Transmission oil temp 14 Cruise off CRUISE OFF AT TEMP HIGH 24 high Cruise deactivated/can- CRUISE CANCELLED 15 cel 25 DEF Level Low Level 1 DEF LOW REFILL SOON Cruise is Resuming to ENG NOT START AFTER CRUISE RESUMED 26 DEF Level Low Level 2 16 set speed “VALUE” KM ENG NOT START AFTER 17 Press Clutch for MT PRESS CLUTCH DEF Level Low Level 3 27 “VALUE” KM Press Brake for MT PRESS BRAKE 18 ENG NOT START AFTER DEF Level Low Level 4 Transmission Failure 28 “VALUE” KM 19 Limp home Activated AT FAULT ENG NOT START AFTER DEF Level Low Level 5 Visit Service Center 29 “VALUE” KM Transmission Failure ENG NOT START NEXT DEF Level Low Level 6 20 Drive Cautiously Visit AT FAULT 30 KEY ON Service Centre 31 DEF Level Low Level 7 ENG STOP DEF EMPTY Shift to Park (P) - vehi- 32 DEF Quality Low Level 1 LOW DEF QLTY 21 cle Stop function for AT SHIFT-> P LOW DEF QLTY ENG OFF vehicle DEF Quality Low Level 2 33 “VALUE” KM Shift to Park (P/N) - ve- LOW DEF QLTY ENG OFF DEF Quality Low Level 3 22 hicle Start function for SHIFT->P/N 34 “VALUE” KM AT vehicle LOW DEF QLTY ENG OFF DEF Quality Low Level 4 23 Jet Pump Fault FUEL SYS FAULT 35 “VALUE” KM

79 DASHBOARD AND FEATURES

Warning Messages on SN Warning Title/ Title Instrument Cluster LOW DEF QLTY ENG OFF DEF Quality Low Level 5 36 “VALUE” KM LOW DEF QLTY ENG NOT DEF Quality Low Level 6 37 START 38 DEF Quality Low Level 7 LOW DEF QLTY ENG STOP

SCR Fault Level 1 SCR FAULT 39 SCR FAULT ENG OFF SCR Fault Level 2 40 “VALUE” KM SCR FAULT ENG OFF SCR Fault Level 3 41 “VALUE” KM SCR FAULT ENG OFF 42 SCR Fault Level 4 “VALUE” KM SCR FAULT ENG OFF SCR Fault Level 5 43 “VALUE” KM SCR FAULT ENG NOT SCR Fault Level 6 44 START 45 SCR Fault Level 7 SCR FAULT ENG STOP

80 DASHBOARD AND FEATURES Tell Tales Warning Lamps Color Indicator Remarks

1. This lamp comes on when ignition is switched ‘ON’. Once engine is Malfunction started, it turns ‘OFF’. Indication Lamp Amber 2. It remains ‘ON’ for any engine related fault that may increase emis- (MIL) sion levels of the vehicle beyond the regulatory norms. Contact the TATA MOTORS Authorised Service Centre for rectification.

1. This lamp comes on when ignition is switched ‘ON’. Once engine is started, it turns ‘OFF’. Check Engine Lamp Amber 2. This lamp comes on continuously if a fault arises in Engine Man- agement System. Contact the TATA MOTORS authorized service centre. 1. This lamp comes on when the system disables engine start if the original key is not used. 2. Lamp blinks: Vehicle is in immobilized condition when key is not inserted. Immobilizer Red 3. Lamp ON: Problem with key/system. Contact a TATA MOTORS Au- thorized Service Centre. 4. Lamp OFF: Normal condition (Authenticated user) and engine will start.

81 DASHBOARD AND FEATURES Warning Lamps Color Indicator Remarks

Pre-Heat indicator / 1. This lamp comes on when ignition key is in ‘ON’ position. Glow Plug indicator Amber 2. Engine shall be started only after this indicator goes ‘OFF’. (Diesel)

Indicates direction indicated by the turn signal. Blinks along with buzzer while operating left/right turn indicator only when ignition is switched ‘ON’. The direction indicator arrow on Instru- Turn Signal Green ment Cluster flashes along with external indicator lights as selected. Both Tell tales shall blink simultaneously when Hazard switch is pressed irrespective of Ignition ON and the Tick-Tock sound shall be given when any one or both the Tell tales are ON.

This lamp comes on when the high beam headlamps are switched High Beam Blue ‘ON’ or flashed.

1. This lamp comes on when ignition is switched ‘ON’ and goes ‘OFF’ once required engine oil pressure is developed after starting the engine. Low Oil Pressure Red 2. If the low oil pressure indicator does not glow or remains ‘ON’ with indicator the ‘IGN’ ‘ON’ and engine is running, it indicates a fault in the electrical circuit / lubrication system. Contact the TATA MOTORS Au- thorized service centre.

82 DASHBOARD AND FEATURES Warning Lamps Color Indicator Remarks

This lamp comes on when ignition is switched ‘ON’ however it will be switched OFF after pre check of 4sec. Battery charging Red If it remains ‘ON’ while the engine is running, it indicates that the battery is not getting charged. Switch off all unnecessary electrical equipment and contact the TATA MOTORS Authorized service centre.

Seat belt warning indicator comes ‘ON’ for 4 seconds, when ignition is turned ‘ON’. If seat belt is not fastened and speed is less than 15 Kmph, then seat belt telltale will turn ON as initial warning. If seat belt is not fastened and vehicle speed goes above 15 Kmph, then final warning will start with telltale flashing and Audio chime for 90 sec- Driver seat belt warning Red onds. After 90 seconds, telltale will be ON and Audio chime will be OFF. Note:  Telltale will turn off either when seatbelt is buckled or Reverse gear is engaged when it is in initial warning stage.  When it is in final warning with Chime ON, the telltale will be OFF on fastening the seat belt or engaging the reverse gear. In case of HHC malfunction HHC warning lamp will remain continuously HHC Warning lamp Amber ON. Please take your vehicle to nearest TATA authorized service centre at (if available) the earliest.

83 DASHBOARD AND FEATURES Warning Lamps Color Indicator Remarks This lamp comes on when ignition is switched ‘ON’ and goes ‘OFF’ Airbag status Red in approx. 4 seconds. If it continuously remains on or blinks then (if available) contact the TATA MOTORS Authorized service centre immediately. This lamp comes on momentarily when ignition is switched ‘ON’. Once parking brake is released, it turns ‘OFF’. If it remains ‘ON’, it Park Brake / Brake Fluid indicates Red Low / EBD malfunction 1. Brake fluid level is low. 2. Park brake is applied & turns ‘OFF’ when it is released. 3. EBD malfunctioning Illuminates when ignition is switched ‘ON’ and goes ‘OFF’ in approx. 4 seconds. If the engine is overheating, this indicator blinks along with an audible buzzer at his stage Contact the TATA MOTORS Authorised Ser- vice Centre immediately. This symbol blinks along with audible High Coolant Red buzzer when engine coolant temperature is more than normal. Temperature When engine coolant temp increases to hazardous level, Tell tale shall blink with RED color and it is accompanied by audio warning. Note: Never remove the radiator pressure cap from the radiator when the engine is hot. Do not restart the engine until the problem has been duly attended.

84 DASHBOARD AND FEATURES Warning Lamps Color Indicator Remarks

The lamps comes on when ignition is switched ‘ON’ and goes ‘OFF’ in 3 seconds. The lamps remains on continuously if there is any malfunction ABS Amber in ABS. Normal braking system will be operational without assistance of ABS. Contact the TATA MOTORS Authorized service centre. Illuminates momentarily when ignition is switched ‘ON’. The symbol lights up continuously if fuel level in the tank is low. Fuel needs to be filled immediately. Low Fuel indicator Amber IMPORTANT: The telltale warning lamp will start flashing if there is any fault in the fuel system. Contact the TATA MOTORS Authorized service centre immediately. This symbol lights up when the ‘IGN’ is turned ‘ON’ and shall go ‘OFF’ after Cruise Control lamp 4 sec. The Cruise Control is used to indicate the status of cruise control Green (if available) system to the driver. Lamp ON indicates cruise control feature is present and it is activated.

Press Clutch Pedal to Press Clutch: The lamps comes on ON with IGN ON till user presses the Start Engine Amber clutch pedal to start the engine. (if available) The lamp remains on continuously if excess water is accumulated in the Water in fuel fuel filter. Contact the TATA MOTORS Authorised service centre to drain indicator Amber the water immediately to avoid serious damage to the fuel injection sys- (Diesel) tem.

85 DASHBOARD AND FEATURES

Warning Lamps Color Indicator Remarks

Daytime running lamps DRL are used to increase the visibility of the vehicle to other drivers during Green (DRL) (if available) daytime. This lamps comes on when the Day Time Running lamp is ‘ON’.

All four door and Tail gate are indicated independently when the Door Ajar lamp Red respective door or tail gate is open.

The lamps comes on if Hill Decent Control System is activated. If HDC Warning lamp Amber continuously ON then HDC system is at fault condition, Please take your (if available) vehicle to nearest TATA authorized service centre at the earliest

Rear Fog Lamp Amber The lamps comes on when the rear fog lamp is ‘ON’. (if available)

Front Fog Lamp Green The lamps comes on when the front fog lamp is ‘ON’. (if available)

Key Not Detected This lamps comes on when the Valid Smart key is not detected inside the Amber (if available) vehicle.

86 DASHBOARD AND FEATURES Warning Lamps Color Indicator Remarks

Electronic Stability Pro- If continuously ON then ESP system is at fault condition, Please take gram (ESP) Amber your vehicle to nearest TATA authorized service center at the earliest. (if available)

The Front passenger seatbelt warning indicator turns ON when ignition is turned ON. If front passenger seat is occupied by adult, the warning lamp remains ON as long as the co-driver seatbelt is not fastened. Front passenger Seat If seatbelt remains unbuckled and vehicle goes above 15 kmph, Red Belt Indicator then final audio warning will go on for 90 seconds. Note: Once the seatbelt is fastened the buzzer and warning lamp turns OFF. Seatbelt reminder remains OFF when reverse gear is engaged.

87 DASHBOARD AND FEATURES Warning Lamps Color Indicator Remarks This lamps comes on when ignition is switched ‘ON’ and goes ‘OFF’ after 4 Seconds. When the vehicle speed cross 80 kmph, then speed limit warning indicator turns ‘ON’ along with audio chime for every 2 minute chime (Audible warning). If vehicle speed crosses 120 kmph, the speed limit warning indicator turns Speed limit warning 'ON' along with an audio chime (audio warning) continuously, until the vehicle Amber indicator speed is above 120 kmph. If vehicle speed is between 80 kmph and 120 kmph, then the audio chime (audio warning) will become less frequent but the speed limit warning indicator will remain ‘ON’ continuously. When the vehicle speed is reduced below 80kmph, then the speed limit warning indicator and the audio chime (audio warning) will turn off.

The lamp blinks constantly to indicate that the DPF needs to eliminate the trapped pollutants (particulate matter) through the regeneration process, it therefore does not indicate a malfunction. The lamp remains off during the entire DPF regeneration and it lamp up only when driving conditions require the driver to be notified. To switch off the lamp, keep the car running until rd DPF Lamp Amber regeneration is complete (ideally at 3 gear, 60 kmph. with engine speed over 2000 rpm). The process normally takes about 20 minutes. Note: Failure to obey the correct procedure for long distance when the DPF lamp comes ON can cause the warning lamp (MIL) to come ON. In that case, please contact nearest TATA authorized service center to restore correct DPF operation.

88 DASHBOARD AND FEATURES Warning Lamps Color Indicator Remarks

ECO ECO lamp ON indicates Economy drive. This mode is used to achieve Green (if available) better fuel economy.

SPORT SPORT lamp ON indicates Sport drive mode. This mode is used to when (if available) Amber more torque is required.

CITY CITY lamp ON indicates City drive mode. This mode is used to achieve (if available) White optimum torque with fuel economy.

This Telltale warns the driver once urea level is detected to be low. Urea Level Amber This TT monitors for emission issues.

This features monitors the catalyst health & warns the user if there is SCR Fault Amber a malfunction

89 DASHBOARD AND FEATURES Audio Reminders (if available) 5. Driver Seat Belt Reminder sounds and informs user to rotate steering wheel. 1. Key-in Reminder/Audio Warning If seatbelt is not fastened and vehicle goes above 15 kmph, then final audio 8. Drive Mode Chime While leaving the vehicle, if you forget warning will go on for 90 seconds. Seat If you changes drive modes from city to the key inside the vehicle in ignition belt tell-tale lamp will remain continu- eco or eco to sports one time drive mode ‘OFF’ position, an audio warning will ously ON when audio alarm is active. sound. Remove key to stop the warning. chime sounds. 2. Park Lamp ‘ON’ Reminder NOTE 9. DEF System Chimes Fasten the seatbelt to stop audio While leaving the vehicle, if you forget to warning. If DEF Level or DEF Quality or SCR Fault turn ‘OFF’ the headlamps, buzzer will becomes critical low then continuous pe- sound. Switch ‘OFF’ lamps to stop the 6. Front Passenger Seat Belt Re- riodic chime will sound. warning sound. Do not forget to turn minder ‘OFF’ your lamps as it may drain the ve- 10. AT Chimes If front passenger has not fastened seat- hicle battery. belt and if vehicle speed goes above 15  Whenever Driver try to switch off igni- 3. Park Brake ‘ON’ Reminder kmph, then final audio warning will go on tion while gear lever not in Park posi- If park brake is applied and vehicle is for 90 seconds. Seat belt tell-tale lamp tion then single chime will sound to driven, Telltale lamp will turn ‘ON’ and will remain continuously ON when audio remind driver to move gear level to buzzer will provide audio warning contin- alarm is active. Park position and then switch off ig- uously. Disengage the park brake to stop nition. NOTE audio warning.  Whenever Gear level not in Neutral Fasten the seatbelt to stop audio or Park position & if driver tries to 4. Reverse Gear Reminder warning. start the vehicle then single chime If reverse gear is engaged, the buzzer will be sound to remind driver to take sound will alert you. 7. ESCL Chime gear level in Park or Neutral position If electronic steering column lock gets in- and then start the vehicle. advertently engaged, this chimes 90 DASHBOARD AND FEATURES Combi-Switch (RH Stalk) Pull the lever back to normal for low 1. To activate and deactivate DRL, keep beam. the ignition switch in ‘ON’ position and switch ON-OFF parking lamp 4. High Beam Flash (spring return) twice within approximately three sec. To flash the high beam, pull the lever 2. Activation and deactivation of DRL towards you from the normal posi- can be done by DRL soft switch tion. It will return to its normal posi- which is available on head unit display. tion when you release it.

iv. Low Beam 5. Headlamp Rotary Switch Rotate stalk to turn ‘ON’ the Low i. OFF Position Beam function. All lamps will remain ‘OFF’. v. Auto Light 1. Left Turn Signal - Move the lever ii. Parking Lamp The headlights will be automati- fully upward. cally switched ON depending on Rotate stalk to turn ‘ON’ the Park- 2. Right Turn Signal - Move the lever ambient light conditions (while en- ing lamps. fully downward. tering a tunnel or when it is twi- light). NOTE iii. Day Time Running lamps (DRL) 6. Lane Change Signal When the turn is completed, the (if available) signal will cancel and the lever will To signal a lane change, move the lever Day time running lamp are used to in- return to its normal position. slightly up or down to the point where the crease the visibility of the vehicle to oth- turn signal light begins to flash, but the - Move the lever forward ers drivers during daytime. 3. High Beam lever does not latch. The turn signal will to select the high beam function. flash 6 times automatically.

91 DASHBOARD AND FEATURES 7. Head Lamp leveling Rotary Combi-Switch (LH Stalk) 2) Slow Wipe Switch Push the stalk towards position (2) for continuous slow wipe. 3) Fast Wipe Push the stalk towards position (3) for continuous fast wipe. 4) Flick Wipe (spring return) Pull the stalk downwards and hold it for continuous wipe, the wiper continuously wipes across the windshield at low speed till the stalk is released. 0) ‘OFF’ Position 5) Front Windshield Washer Inner rotary switch on right hand stalk is  Pull the lever little longer, The wiper is switched ‘OFF’. provided for head lamp leveling. With the to spray the washer fluid inner rotary switch, Head lamp leveling 1) Intermittent Wipe on the windshield. can be done with head lamp in Low  The windshield wipers operate for 3 Push the stalk upwards to op- Beam and in ‘ON’ position. Select cor- cycles after the lever is released and erate intermittent wipe. rect position before start of trip when the 1 more cycle after 5 seconds. vehicle is stationary. Depending on the Inner rotary switch on left hand number of passengers and luggage in stalk is provided for intermittent front the vehicle headlamp focus may change. wiper delay. The switch has 5 delay tim- This can be adjusted by rotating the ers. knob to one of the 3 level positions.

92 DASHBOARD AND FEATURES Auto Front Wipe (if available) 6) Rear Wash and Wipe Rear Wipe If your vehicle is fitted with rain and light (if available) Turn the rotary knob counter sensor, the wipers will automatically clockwise such that it aligns wipe the windscreen, if it senses rainfall. its positions with arrow mark to operate Make sure that the wiper stalk is in Auto rear windshield wiper continuously. position. NOTE NOTE Rear wiper will not work as long as When you crank the engine, the tailgate is open. supply to washer motor is momentarily cut off. Rear Windshield / Wiper and Washer Switch Turn the rotary knob counter clockwise such that it aligns its positions with arrow mark Rear Windshield / Wiper and and hold it to operate rear Washer windshield wash and wipe function. It Turn the rotary knob clockwise will return to ‘Rear wipe’ position as soon and release to operate rear as it released and continue to wipe. windshield wash and wipe. The windshield wipers operate for 3 cycles.

93 DASHBOARD AND FEATURES

WARNING Fascia Switches If you operate wash and wipe func- Fascia switches are provided on the cen- tion for more than 15 seconds the ter console below HVAC control panel. controller cuts off the supply to the washer motors to avoid overheating.

Rain / Light Sensor (if available) Rain & light sensor is integrated sensor & mounted on front windshield glass to sense rain & light. As per the input from sensor, the wipe and light function will work automatically.

1. Rear fog lamp switch (if available)

2. Front fog lamp switch(if available)

3. Hazard warning switch

4. Economy mode switch (if available)

5. Sports mode switch (if available)

94 DASHBOARD AND FEATURES Steering Wheel Switches (LHS) 3. Phone receive / PTT 4. Source (if available) (Push to Talk) Press above switch to select Press above switch to accept incoming the required source in the infotain- call when a cell phone is connected via ment system i.e. USB, AUX, AM, FM Bluetooth. and Bluetooth. Voice Recognition 5. Mute / Phone Reject To start, long press the voice activation Press above switch to reject button provided on the steering wheel. or hang up a phone call. It is The system mutes/ pauses the currently also used to mute the volume of music played audio and you will hear a beep system / radio. sound to indicate the activation of the voice recognition feature. The system NOTE also display the icon on the top right cor- For more information of steering 1. Volume ner of the screen to indicate activation of wheel switches refer infotainment voice recognition. manual. Press above switch to increase or de- ((Refer link -http://service.tatamo- crease volume of music system / radio. NOTE tors.com/content/owners-manual 2. Seek Forward/Back- The system will start recognizing )if available) ward your voice command only after the beep. So, speak your command Press above switch to change radio only after you hear the voice acti- channels. vation beep.

95 DASHBOARD AND FEATURES Steering Wheel Switches (RHS) 2. OK / Select & Long Press Changing the Set Cruise (if available) for Setting Speed Press above switch to select the op- The set cruise speed can be adjusted tion and also press long (approx. 3) (i.e. increased or decreased) using ‘+’ (to to go directly to Instrument cluster increase) or ‘-’ (to decrease) switches on settings. steering wheel. The speed increases and 3. Cruise Resetting/Set- decreases on a single press. The ting Speed Increas- changed speed will be shown on the ing/Decreasing Switch speedometer. Keeping the switch pressed increases or decreases the Press the cruise control master  speed continuously till the switch is re- switch on steering wheel. leased. The set speed can also be in-  Accelerate the vehicle to the decreased by pressing the accelerator pe- sired speed. dal till the desired speed is achieved and 1. Instrumentation Controls(IC)  Press the ‘SET’ button on steering then pressing the ‘SET’ button. The set wheel switch to set the desired i. Instrumentation Controls speed can also be decreased by press-

Scroll Up cruise speed. The cruise control indicator on instrument cluster will ing the brake pedal (The cruise indicator Press above switch to scroll up on In- turn ‘ON’. will turn OFF) and slowing down to de- strument Cluster display.  Remove your foot from the acceler- sired speed and then pressing the ‘SET’ ii. Instrumentation Controls Scroll ator pedal. button (The cruise control indicator will Down turn ‘ON’ again). Once Cruise control is activated the ve- Press above switch to scroll hicle automatically maintains the stored down on Instrument Cluster display. speed.

96 DASHBOARD AND FEATURES 4. Cruise Control Master Mic (if available) Infotainment System Display Switch (if available) Cruise speed can be resumed only if cruise control is deactivated by depressing Brake Pedal. To resume the previously set cruise speed, accelerate the vehicle to a speed above approx. 32 kmph and press reset (‘RES’) switch. 5. Cruise Control Deac- tivating Switch There are several ways to deactivate cruise control: Mics are provided on roof near the roof  Applying brake / clutch. lamp.  Press deactivation switch on Steer- NOTE ing Wheel For more information, refer info-  Activation of ESP/ TCS system. tainment manual. ((Refer link -http://service.tatamo- tors.com/content/owners-manual )if available)

97 DASHBOARD AND FEATURES Speakers & Tweeter (if available) USB/AUX Port (if available)

Tweeter

Speaker Connect your portable digital music play- Speakers and tweeters are provided on ers, pen drives etc. to this socket for models with infotainment system. Provi- playing music tracks through the vehi- sions are given for music system and cles music system. speakers on versions without infotainment system.

98 DASHBOARD AND FEATURES

Smart Charger (if available) Power Socket NOTE Use of inappropriate electrical accessories can cause damage to your vehicle’s electrical system. Make sure that any electrical accessories you use are designed to plug into this type of socket and rating.

It is available between the front passen- Power socket is available inside the ger seats below the rear stowage area cooled storage box on the center con- for second row passengers. sole. It is used to charge the mobile phone, The power socket will work when the ig- Power Bank etc. nition switch is in the “ACC” or “ON” position. This socket can be used to provide 12V (10A) power for electrical accessories.

99 DASHBOARD AND FEATURES Antenna Option II Roof Grab Handle (if available) Option I

Grab handles are installed on the roof Shark fin antenna is provided on the for all seats except for the driver’s seat. roof at rear end. Antenna is located on the roof. Turn an- These help the passengers to position tenna anticlockwise to remove from ve- themselves comfortably during the jour- hicle, if required. ney.

100 DASHBOARD AND FEATURES Front Fog Lamps An indicator on the switch will be illumi- Rear Fog Lamps nated when the front fog light is ‘ON’. (if available) (if available) Cornering Feature: Rear Fog Lamp is provided on Front fog lamp is located on front rear bumper to improved visibility in ad- bumper. When visibility is poor due to For front fog lamp cornering feature the verse weather conditions to vehicles be- fog, snow or rain, use the fog lamps to Head Lamp must be ‘ON’. hind you. improve visibility as well as making it As you turn steering wheel to left or right, easier for other road users to see you. the corresponding fog lamp will automatically get ‘ON’.

For switching ‘ON’ the rear fog lamps, front fog lamp must be ‘ON’. For switching ‘ON’ the Fog lamps, either Operate the rear fog lamp switch pro- the Head Lamp or Parking lamp must be vided on fascia to ‘ON’ or ‘OFF’ the fog ‘ON’. lamp. Operate the front fog lamp switch pro- An indicator on the switch will be illumi- vided on fascia to ‘ON’ or ‘OFF’ the fog nated when the rear fog light is ‘ON’. lamp.

101 DASHBOARD AND FEATURES Puddle / Ajar Lamp Roof Lamp Option 2 Interior roof lighting lamp is provided on the roof with inbuilt switch. Front Roof lamp Option 1

Puddle / Ajar Lamp is provided on driver, Rear Roof lamp (if available) front passenger & rear doors trim. It will be ON only when particular door is in open condition.

1. Spot / Reading Lamp for Front passenger side 2. OFF 3. DOOR 4. ON 5. Spot / Reading Lamp for Driver side 102 DASHBOARD AND FEATURES The switches has below functions: 4. ON - The lamp will turn Side reading lamps (applicable for var- ‘ON’ as long as the switch iants with Sunroof) are provided above 1. Spot / Reading Lamp for Front second row seat passenger doors. is in this position. passenger side The lamps will turn ‘ON’ with dimming 5. Spot / Reading Lamp for Driver The front row interior lamp when either of the door is open. When

side has separate switches to the all doors are closed and auto lock operate the spot / reading lamp for The front row interior lamp mode is active, the lamps will turn Front passenger side. has separate switches to ‘OFF’ with dimming. This helps settling in the seat. operate the spot / reading lamp for 2. OFF - In this position, the Driver side. Inbuilt switches are also provided on

lamp will remain ‘OFF’. both lamp to operate (Switch ‘ON’ or Side Reading Lamps (if available) 3. DOOR - In this position, ‘OFF’) the lamps independently when the lamp turns ‘ON’ with required during journey. dimming when either of the doors are opened. When the

last door is closed, the lamp will turn ‘OFF’ with dimming. This helps settling in the seat and inserting the key in the ignition switch. When the key is turned to the ‘IGN’ position,

the lamp goes ‘OFF’ immediately.

103 DASHBOARD AND FEATURES Boot Lamp Side Indicator Lamp on ORVM Front Lamp

Boot lamp is available in the rear lug- It is provided on outer part of ORVM. 1. Position / DRL /Turn indicator lamp (if available) gage compartment to light up the lug- It will turn ON when the turn signal in- gage area. dicator switch is ON and Hazard Warn- 2. High beam lamp Boot lamp is without switch type. It will ing indicator switch is ON. 3. Front fog lamp (if available) be ON only when tailgate is open. 4. Low beam lamp

104 DASHBOARD AND FEATURES Lamp Condensation / Fogging Tail Lamp Condition Condensation is a natural phenomenon in Lamp. This occurs mainly because of atmospheric condition/weather change. During normal condensation, thin film of mist is visible on the inside surface of the exterior lens. Generally, this condition is considered normal and can be eliminated by turning on the headlamp with engine running or during normal driving conditions. 1. Turn indicator NOTE 2. Reverse lamp  Headlamp fogging / condensation is natural occurrence and 3. Stop lamp there is no need to replace the 4. Parking lamp unit to resolve the issue.

 High-pressure washer jet direct on vent system of lamp are not recommended, there might be possibility of water ingress causing heavy fogging.

105

DASHBOARD AND FEATURES

106 STOWAGE AREAS 1) Glove Box ii) Glove Box Illumination iii) Stowage Detail i) Opening and Closing

The glove box lamp illuminates when the Following items can be stowage in glove glove box is opened. box. To Open – Pull the lever to open the glove box flap. NOTE 1. Owner’s manual and other vehicle document, To Close - Lift glove box flap until it en- Make sure that glove box flap is gages. closed while driving. 2. First aid kit, Visiting card, Pen, Re- ceipts etc.

107 STOWAGE AREAS iv) Cooling Facility (if available) 2) Goggle Holder (if available) 3) Utility Pockets on Front Doors

On selected models cooling facility is Goggle holder is provided near the roof Utility pockets are provided on front provided below driver foldable arm rest. lamp. doors and it can be used to keep follow- It cools only when the A/C is ON. Close ing items. the vent by rotating the knob, whenever Magazine/ paper cooling is not required. 1. 2. Umbrella holder 3. Water bottle

NOTE Remove the water from umbrella and fold it properly before storing it in umbrella holder. 108 STOWAGE AREAS 4) Utility Pockets on Rear Doors 5) Mobile / Wallet Stowage 6) Cup Holder for Front Passenger

Utility pockets are provided on rear Place for keeping wallet / mobile is pro- Space for cup holder are provided in cen- doors and it can be used to keep follow- vided in front of Gear shifter lever. tre console. ing items. 1. Mobile holder 2. Magazines/books 3. Water bottles etc.

109 STOWAGE AREAS 7) Stowage for Rear Passenger 8) Stowage below Arm Rest 9) Foldable Arm Rest (if available) (if available)

Stowage below front arm rest with chiller A foldable arm rest has been provided in Stowage for rear passenger is provided is provided on center console between the rear seat. It also has two cup holders, on rear side of floor console between the the front passenger seats. It can be used which can be accessed by opening the front passenger seats. It can be used to to keep small items. cover. When not required, fold the arm- keep mobile charger, mobile and small rest back into the seat. items like wallet, Power bank etc. NOTE  Remove all items and cups before folding the cup holders.  Use cups, containers, bottles of right size and which have lids. The content could otherwise spill. 110 STOWAGE AREAS

10) Tailgate Compartment WARNING Stowage below Load Floor  Distribute the items of luggage as evenly as possible.  Position heavy loads as far forwards as possible and as low down in the trunk as possible.  Never allow occupants to travel in the luggage compartment.  Do not place anything on luggage cover as it could obstruct driver’s rear view. Also in case of an accident or sudden braking, it could cause an injury to occupants. Store the luggage in tailgate compart-  The luggage cover can be lift. Luggage cover is designed only for hid- ment. You can keep suitcase bag etc. ing the luggage compartment.

111 STOWAGE AREAS 11) Hooks  Never hang hard, sharp-edged or Front Seat Back Pockets (if available) fragile objects on the coat hook. i) Coat Hanger (if available) ii) Hooks in Luggage Compartment (if available)

Rear pockets are provided behind the front seats for keeping small magazines Coat hanger is provided for rear passen- /Notebook etc. ger near grab handle. NOTE WARNING These hooks are provided on both sides in luggage compartment for hanging Do not hang objects on coat hooks  The coat hook cannot restrain small carry bags carrying up to 3 kg which can obstruck the curtain heavy objects or items. weight only. airbag deployment during impact.  Do not hang objects on coat

hooks which can obstruck the NOTE curtain airbag deployment during impact. Do not use these hooks for secur- ing luggage like using nets etc.

112 CLIMATE CONTROL The Climate Control regulates the temperature inside the vehicle and filter the dust particles in cabin based on the user set temperature settings. Air Distribution- The air is distributed through the vents in the passenger compartment as shown below:

113 CLIMATE CONTROL Air Vents Side Vent for Rear Passenger (if available) Centre Vent Side air vents are provided on both side Centre air vents are provided on dash- of B pillar for rear passenger. board. Air flow and its direction can be adjusted with the help of knob provided Air flow and its direction can be adjusted on respective vent. with the help of knob provided on respective vent.

Side Air Vents (Front)

Centre Air Vents (Front) Side Air Vents (Rear)

114 CLIMATE CONTROL 1. HVAC Controls (if available) A. Temperature Control B. Fresh / Recirculation Air Mode Press the switch to activate / deactivate air recirculation mode.

LOW HIGH

The temperature control knob allows you to adjust the temperature. The temperature can be increased by rotating the Press to ‘ON’ or ‘OFF’ knob towards the red segment (clock- A. Temperature Control wise) and decreased by rotating it to- Recirculation mode: (Indicator light B. Fresh / Recirculation air mode wards the blue segment (anti-clockwise). ‘ON’) C. Blower Speed Control Air in the passenger compartment recir- culates. No fresh air enters the compart- D. AC ON/OFF Switch ment. E. Air Distribution Control Always use when:  Driving on a dusty road or through tunnel.

 On signals or slow traffic to avoid

traffic pollution.  Maximum cooling is required.

115 CLIMATE CONTROL Fresh Air Mode: (Indicator light ‘OFF’) C. Blower Speed Control D. AC ON/OFF Fresh air is drawn into the vehicle. Always use when: OFF HIGH  Discomfort is felt or windows are fogging up.

 Using or air flow modes during demist / defrost. This is to turn ‘ON’ the blower and select Press the switch to activate / deactivate desired blower speed.  Using normal heating mode. the AC. The indicator lamp in the button will light up when climate control is activated.

NOTE The AC can be switched ‘ON’ only if the blower is ‘ON’ and engine is running. When AC is switched ‘ON’, engine idling RPM increases marginally to adjust the AC compressor load. When desired temperature at evapora- tor is achieved Ac compressor will self displace optimum refrigerant flow.

116 CLIMATE CONTROL

NOTE  While starting the vehicle itself E. Air Distribution Control after long duration (more than  Condensation may drip from the days), following procedure underside of the vehicle when it 15 needs to be followed to meet AC is in cooling mode. Traces of wa- performance. ter on the ground are normal and are not a sign of leakage or - Start the vehicle with AC & malfunction. Blower in OFF condition in idling for 2~3 minutes.  Ventilate the vehicle for a brief Then switch ON the AC & period during warm weather. - This is to select the air distribution pat- Blower and run it for another tern as described in the table. This will speed up the cooling minutes in idling for process and the desired vehicle 2~3 Directs air through the cen- proper circulation of refriger- interior temperature will be ter and side air vents ant & oil to lubricate the inter- reached quickly. Directs air through the cen- nal parts of AC system.  Never cover the air vents or air ter, side and foot well vents  Rear blower will be effective af- intake grilles in the vehicle inte- Directs air through the foot ter min of front HVAC run- rior. 5-10 well air vents ning (after cabin cooling).  If the AC is not used for a long Directs air through the de- period, such as during winter, it froster & foot well vents

may not give the best perfor- (Default fresh air mode)

mance when you start using it Directs air through the defroster vents (Default fresh again. Operate the AC at least once a month to maintain opti- air mode) mum performance. Directs fresh air enters in

the compartment.

117 CLIMATE CONTROL Recommended basic settings of the control elements of air conditioning system for the respective operating modes. These may vary depending on individual requirements and weather conditions.

Control Knob Position Button Position Fresh / Recircula- Air Flow Direction Blower Speed Air Temperature AC ON/OFF Functions tion air mode

Normal heating or 2nd or 3rd Desired temp. Fresh air mode. Switched OFF To MAX speed Briefly switch ON to To the extreme right and then 2nd or Fresh air mode Switched OFF Quick heating up to the stop 3rd then Recirculation mode Recirculation 1st to 3rd Desired temperature Switched ON Normal Cooling mode To MAX speed To the extreme left Recirculation and then 2nd or Switched ON Quick Cooling up to the stop mode 3rd Fresh air mode Switched ON Demisting 2nd or 3rd Desired temperature (Default) (Optional) Fresh air mode Switched ON To MAX speed Desired temperature Defrosting (Default) (Optional)

118 CLIMATE CONTROL 2. Fully Automatic Temperature 5. Blower speed control up switch Also, when the display is not in climate mode then climate information will be Control (FATC) (if available) 6. Temperature control knob displayed on the all-time display provide FATC system controls the inside temper- 7. Auto ‘ON’ selection switch on the bottom bar. ature of the vehicle automatically and provides maximum passenger conven- 8. Fresh air / recirculation switch 1. Rear Window Demister Switch ience regardless of outside weather con- 9. AC compressor ‘ON / OFF’ switch This switch operates rear win- ditions. 10. OFF mode switch dow demister. The system will be deactivated after 15 Display Unit min of continuous operation. 2. Maximum Defrost Switch A. This switch directs the main airflow towards windscreen for faster defrosting. (It also overrides any mode selection you may have made.) FATC display is shown on infotainment display screen. B. When you turn off the button, the system returns to its default setting. FATC functions can be controlled using 1. Rear window demister switch both the FATC control panel and the NOTE touch screen display. 2. Maximum defrost switch For your safety make sure you 3. Air distribution (mode) switch Whenever the user presses any switch or have a clear view through all the turns the rotary knob, then the display windows before driving. 4. Blower speed control down switch unit will show the relevant Climate Infor-

mation. 119 CLIMATE CONTROL 3. Air Distribution (Mode) Switch 4. Blower Speed Control Down increased by steps of 0.5ºC. User can se- Switch (Low) lect temperature range from 18ºC to In AUTO mode, the FATC sys- Press the Blower Speed con- 30ºC. Whereas the anticlockwise direc- tem will regulate the mode tion decreases the temperature. automatically. However, user trol down button to decrease override is possible with the the blower speed. When you set the temperature to its use of MODE button to select the desired 5. Blower Speed Control Up Switch lower limit (Lo) or its upper limit (Hi), the airflow mode. (High) system runs at full cooling or heating only. It doesn’t regulate the interior tem- Each time you press the MODE button, Press the Blower Speed con- perature. the display shows the mode selected. trol up button to increase the 7. Auto ON Selection Switch blower speed. Directs air through the center and side air vents NOTE Directs air through the cen- In ‘AUTO’ mode, the FATC system ter, side and foot well vents will regulate the blower speed au- Directs air through the foot tomatically. well air vents 6. Temperature Control Knob To put the automatic climate control in fully automatic mode: Directs air through the defroster & foot well vents A. Press the ‘AUTO’ button. (Default fresh air mode) B. Set the desired temperature by turning temperature control knob. The Directs air through the defroster vents (Default fresh display will show all the functions Turning the temperature control knob during ‘AUTO’ mode. air mode) clockwise increases the temperature of C. The system automatically selects the the air. The desired temperature will be proper mix of conditioned and / or

120 CLIMATE CONTROL heated air that will, as quickly as pos- 8. Fresh Air / Recirculation Switch in recirculation mode, particularly with sible, raise or lower the interior tem- AC OFF, can cause the windows fog up. perature to your preference. A. When the recirculation switch or LED is switched D. When you set the temperature to its NOTE ‘ON’, air from the vehi- lower limit (Lo) or its upper limit (Hi), When Reverse gear is selected , air the system runs at full cooling or cle’s interior is sent throughout the system. intake may switch to recirculation heating only. It does not regulate the mode if previously in fresh mode to interior temperature. B. When the recirculation switch is prevent exhaust fumes from enter- switched ‘OFF’, air is brought in from ing in the vehicle. Semi-automatic Operation outside of the vehicle (fresh mode). You can manually select various func- Whenever discomfort is felt, switch 9. AC ON/OFF Button tions of the climate control system when to fresh air mode. Press the AC compressor it is in fully automatic mode. All other ON/OFF button to turn the air features remain automatically con- NOTE conditioning ON or OFF. The trolled. Making any manual selection The outside air intakes for the cli- AC icon will be activated on causes the word ‘AUTO’ in the display to mate control systems are at the the display when the AC will be ON. go OFF and overridden setting is dis- base of windscreen. Keep this played. System will remain in semiauto- area clear from leaves and other 10. OFF Switch matic mode till ‘AUTO’ is re-pressed. debris. Press the OFF button to switch OFF The system. OFF

The system should be used with recircu- will be displayed on the info- lation air mode for faster heat up and tainment screen cool down, however keeping the system

121 CLIMATE CONTROL

Control Knob Position Button Position (6) (7) (1) (2) (3) (4) (5) (8) (9) (10) Rear Maximum Func- Temperature Auto Air Blower Blower Fresh/air A/C OFF demister defrost Recir tions Distribution Down Up Button Culation

Normal Desired No No No No Desired Desired No No OFF heating Temperature change change change change Speed Speed change change To the ex- Quick No Max treme right till OFF OFF NA Fresh ON OFF change speed heating temp ‘HI’

Normal Desired No No No Desired Desired No No No change OFF Cooling Temperature change change change Speed Speed change change

To the ex- Quick No Max Recircu- treme left till OFF OFF NA ON OFF change lation Cooling temp ‘LO’ Speed To the right up Demist- No No No No No No to the desired ON No change No change ing change change change change change change temperature

122 CLIMATE CONTROL

To the right up Defrost- No Max to the desired OFF ON NA Fresh ON OFF ing change Speed temperature

Panel No No OFF OFF OFF OFF OFF OFF OFF ON OFF change change

123 CLIMATE CONTROL

Quick Cooling HVAC Sensors: 2. Outside Ambient Temperature (OAT) Sensor If your vehicle is parked under the sun, HVAC system is fitted with three sensors you can cool it down fast by following the It is located under the front bumper grill. 1. Solar Sensor steps given below: A solar sensor is on top of the dashboard NOTE Start the engine. 1. at the middle of defroster grill.  Do not cover or spill any liquid 2. Turn on A/C by pressing the button. on sensors. Make sure the temperature control is  Do not cover sensor, this may set to maximum cool. In case of FATC cause the sensor to malfunc- set temperature to ‘Low’ mode. tion. This may lead to FATC not 3. Set the blower to maximum speed functioning to desired level. 4. Open windows half, set air direction towards face and fresh air mode. 3. In-car Sensor on Control Panel 5. When the interior has cooled down to a more comfortable level, close windows and set the controls as required in normal cooling, with recirculation mode ON.

124 STARTING AND DRIVING Pre Driving Checks Daily Check Weekly Check Make sure that  Tyres for abnormal wear, cracks or  Engine oil level damage and embedded foreign ma-  Windshield, windows, mirrors, lights,  Coolant level and reflectors are clean and unob- terial such as nails, stones, etc. structed.  Traces of fluid and oil below vehicle.  Brake fluid level  Tools kit, jack & handle, warning tri-  Windshield washer fluid level angle, owner’s manual, first aid kit NOTE and vehicle documents are available Water dripping from the air condi-  Battery electrolyte level and stored at their locations. tioning system after use is normal.  Fuel level WARNING  All lamps, wipers, wiper blades and NOTE Never put any mat on top of the horn for proper operation.  Tyre pressure to be measured at floor carpet near pedal region.  All switches, gauges and tell tales are cold condition.  All doors, engine bonnet and tail gate working properly.  Check tyre pressure and condi- are securely closed and latched. tion after every 15 days includ- Adjust ing spare wheel.  All passengers are properly re-

strained. All occupants travelling  Seats, head restraints (if available) should always wear seat belts or suit- and steering wheel position. able CRS as applicable.  All the mirrors properly adjusted.  Objects/luggage are secure properly against slipping or tipping.  Rear seat is securely latched.  Sufficient fuel for the trip. 125 STARTING AND DRIVING Driving Tips Personal Driving Style  Driving safety systems are merely aids designed to assist driving. You Fuel consumption, engine, transmission,  Do not press the accelerator pedal are responsible for the distance to brake and tyre wear are mainly affected while starting the engine. the vehicle in front, for vehicle speed by below factors:  Do not warm up the engine when the and anticipating braking in good  Operating conditions of your vehicle vehicle is stationary. time.  Your personal driving style  Always adapt your driving style to suit the prevailing road, weather condi- WARNING Operating Conditions tions, and maintain a safe distance You could lose control of your vehi-  Avoid frequent start and stop as from the vehicle in front. Drive care- cle if you try to adjust the driver's these increase fuel consumptions. fully. seat, head restraint, mirror, steering wheel and fasten the seat belt  Always make sure that the tyre pres-  Avoid frequent, sudden acceleration while driving. There is a risk of an and braking. sures are correct. accident.  Do not carry any unnecessary weight.  Select appropriate gear according to  Regularly, service your vehicle and varying speeds and load conditions. adhere to the recommended service maintenance schedule. NOTE Do not rest your foot on the clutch pedal while driving.

 Switch ‘OFF’ the engine in stationary traffic or at signals.  Keep an eye on the vehicle's fuel consumption.

126 STARTING AND DRIVING Recommended Fuel Economy  Avoid high speed when cornering or  Keep the vehicle clean. Get rid of the Speeds (MT only) turning. not in use luggage/stuff lying in the  Press the clutch fully while shifting boot etc. Gear Speed (km/h) gears (for MT)  Regularly inspect your vehicle for any 1 15  Make sure that vehicle is completely leakages, worn out wires, rat bites etc. 2 30 stationary before you attempt to shift in reverse gear.  Always follow periodic & regular ser- 3 50  Drive slowly on wet roads. vice schedule of the vehicle. 4 70  You can get extra braking from the  Drive smart and smooth in an antici- patory manner. Select driving mode 5 90 engine by shifting to a lower gear. This can help you to maintain a safe to suit your style. 6 105 speed and prevent your brakes from  Do not accelerate excessively when overheating specially while going you are in lower gears (1st or 2nd). Be Good Driving Practices down a hill. gentle on the accelerator when you  Slow down before shifting to a lower are in traffic. In lower gear, opening Tips for Obtaining Better Fuel Effi- gear. This will help avoiding revving more throttle will shoot the engine ciency of the engine causing damage (for RPM keeping the vehicle still at lower MT).  Always maintain the specified tyre speeds which indirectly implies less  Avoid frequent brake application pressure during fuel top-ups and also distance with more fuel. which can cause overheating of before a long trip. Vehicle running  Be in the maximum possible higher brakes. with low tyre pressure will consume gear at a given speed. This reduces more fuel than the one running with  Slow down the vehicle speed while the engine operating speeds which specified tyre pressure. travelling in cross winds. This gives means the engine is running at lower much better control over the vehicle. rpm (Revolutions per Minute) for the 127 STARTING AND DRIVING

same vehicle speed. Lesser the num- the windows the higher will be the re- Gear Speed(km/h) ber of engine revolution lesser the sistance to the vehicle at higher fuel burned. speeds which will reduce the fuel ef- 1 15  Avoid harsh braking. ficiency. 2 30 3 45  Maintain healthy driving habits &  Do not over speed; follow the speed while decelerating, do coasting in limits. More the speed, higher the ex- 4 60 gear and not in neutral or with clutch ternal resistance on the vehicle 5 80 pedal pressed. which will finally result into unneces- 6 100 sary consumption of fuel.  Consider using the car AC when you Avoid heavy loads, e.g. driving at full really require. Consider using lower Running-in Period throttle, during this period. Change blower speeds rather than higher for The more you look after the engine when gears judiciously. cooling as at higher blower speeds it it is new, the more satisfied you will be consumes more electric power which While cruising, brief full-throttle acceler- with its performance in the future. is ultimately drawn from engine by ation within the limits of local traffic laws burning fuel. Avoid rapid acceleration and prolonged contributes to a good break-in. Wide- opened throttle acceleration can be det-  Avoid unnecessary extra electrical high speed running of the engine for the rimental and should be avoided. loading on the car. first 2,000 km.  Stop the engine wisely at traffic sig- Do not exceed the following road speeds NOTE nals. Switch ‘OFF’ the engine at the during running in period. Avoid excessive revving up of en- traffic signal only if the stoppage gine rpm. Do not keep engine at time is high (typically more than 30 idling for long duration. sec).  While driving on highways, drive with

windows closed. The more you open 128 STARTING AND DRIVING

Seat Adjustments WARNING 2. Seat Height Adjustment (if available) Option I Do not adjust the driver's seat while driving. Adjusting the seat while To raise the seat, pull and continue Front Seat Adjustments driving could cause the driver to pumping the lever (2) in the upward di- Following seat adjustments can be car- lose control of the vehicle. rection until the seat is at the desired ried out manually. height. 1. Seat Backrest Angle Adjustment To lower the seat, pump the lever down- To change the seat back rest angle, lean ward until the seat is at desired height. forward slightly and pull up the lever (1). Adjust seat backrest until it reaches de- 3. Seat Forward / Rearward Adjust- sired comfortable position. Make sure ment that lever returns to its original position Lift lever (3) and slide the seat forwards and seat is securely latched. or rearwards. Release lever and make sure that seat is securely latched. NOTE Adjust the seat backrest until your NOTE arms are slightly angled when Adjust the driver seat position in holding the steering wheel. such a way that the driver will be

1. Backrest Angle able to operate the control pedals WARNING comfortably. 2. Seat Height Adjustment (if available) Never travel in a moving vehicle 3. Seat forward / rearward adjustment with the seat backrest in an excessively reclined position as this can be dangerous. You could slide un-

der the seat belt in a collision. 129 STARTING AND DRIVING

Option II WARNING To lower the seat, operate control (2) downward slightly until the seat is at de- Power Seat Adjustment Do not travel in a moving vehicle sired comfortable position. Release the with the seat backrest in an exces- Following seat adjustments can be car- control once seat reaches desired posi- sively reclined position as this can tion. ried out manually. be dangerous. You could slide under the seat belt in a collision. 3. Seat Forward / Rearward Adjust- ment 1. Backrest Angle To adjust the seat position forward, op- To adjust the seat back forward, operate erate control (3) in forward direction control (1) in forward direction slightly slightly until the seat is at desired com- until the seat is at desired comfortable fortable position. Release the control position. Release the control once seat once seat reaches desired position. reaches desired position. To adjust the seat position rearward, op- To adjust the seat back rearward, oper- erate control (3) in rearward direction ate control (1) in rearward direction slightly until the seat is at desired com- slightly until the seat is at desired comfortable position. Release the control

fortable position. Release the control once seat reaches desired position. 1. Backrest Angle once seat reaches desired position.

2. Seat Height Adjustment 2. Seat Height Adjustment

3. Seat forward / rearward adjustment To raise the seat, operate control (2) upward slightly until the seat is at desired comfortable position. Release the control once seat reaches desired position.

130 STARTING AND DRIVING Lumbar Support (if available) Adjustable Head Restraint Front Seat

WARNING Do not drive the vehicle without the seat head restraints. Head restraints are intended to help reduce injuries during an accident.

Continuous (Multiple adjusting position) lumbar support is provided on driver and Adjust the head restraint so that it is as front passenger seat to give you comfort close to the head as possible and the while driving. It is adjusted by the lever center of the head restraint supports the provided on the side of the seat back of the head at eye level. This will backrest. reduce the potential for injury to the head and neck in the event of an accident or similar situation.

131 STARTING AND DRIVING Rear Seat Folding  Press the backrest release knob to  Fold the backrest seat forward. Move fold the backrest seat forward. the driver and front passenger seat Option 1 forward if necessary. 60:40 % Split Seat You can increase the luggage capacity by folding the respective rear seats as required. To fold the seat:

 Follow the same procedure for other rear seat.

132 STARTING AND DRIVING  Press the backrest release knob to  Fold the backrest seat forward. Move Option 2 fold the backrest seat forward. the driver and front passenger seat Rear Seat Folding (Complete Seat forward if necessary. 100%) To fold the seat:  Simultaneously, press the backrest release knobs provided on both side.

NOTE  Ensure that ‘foldable arm rest’ is close before seat folding.  Fold both seats if required.

133 STARTING AND DRIVING

WARNING Rear View Mirrors  You should always engage the Inside Rear View Mirror (IRVM) rear seat back rest if you do not need the through loading fea- (if available) ture. To adjust the mirror move the mirror up,  If the rear bench seat and seat move down or sideways to obtain the backrest are not engaged they best rear view. could fold forwards, e.g. when When driving at night, set the selector braking suddenly or in the event of an accident. tab to select anti-glare mode (if available) to reduce glare from the headlights  The vehicle occupant would of vehicles behind you.  Fold the backrest seat forward. Move thereby be pushed into the seat the driver and front passenger seat belt by the rear bench seat or by forward if necessary. the seat backrest. The seat belt can no longer offer the intended level of protection and could even cause injuries.  Objects or loads in the trunk cannot be restrained by the seat backrest. There is an increased risk of injury.  Before every trip, make sure that the seat backrests and the rear

bench seat/rear seat are engaged and securely latched.

134 STARTING AND DRIVING

NOTE ON/OFF button to turn ON the automatic NOTE dimming function. Use antiglare position only when Objects visible in mirror are actu- necessary, as it reduces rear view The LED indicator on the IRVM shows the ally closer than they appear. Al- clarity. active status of auto dimming function. ways make sure of the actual dis- The auto dimming IRVM is defaults to tance from the road users travel- Automatic Dimming IRVM the ON position whenever the ignition ing behind by glancing over your (if available) switch is turned ON and it is switched shoulder. OFF whenever reverse gear is engaged.

NOTE For proper operation, keep the photocell sensors clean and do not cover the area between the IRVM and the windshield.

Outer Rear View Mirrors (ORVM) You can adjust the outer rear view mirrors manually by joy stick or remotely by 1. Photocell Sensors knob. Adjust the outside rear view mir- 2. ON/OFF button rors to desired position. Automatic dimming rear view mirror automatically controls the glare from the headlights of the car behind you in night time or low light driving conditions. Press 135 STARTING AND DRIVING

Motorized Outer Rear View mirrors NOTE Rear View Mirrors with Joy Stick

(if available) When vehicle is locked, mirrors will Knob (if available) The switch to adjust the motorized mir- be folded automatically. When is rors is located on the driver’s door. You unlock mirrors will be unfolded au- can adjust the mirrors when the ignition tomatically. switch is in the “ACC” or “ON” position. To Adjust the Mirrors 1. Move the mirror selection switch to L Mirror Folding (for left side) and R (for right side) to To fold / unfold the ORVMs, keep the Se- select the mirror you wish to adjust. lector switch in center position (i.e. nei- 2. Use the 4 positions of the knob to ad- ther ‘L’ nor ‘R, position) and then toggle just the rear view mirrors to required down. position.

You can adjust the outer rear view mirrors manually by joy stick knob located in the driver and front passenger door panel. If required mirrors are folded manually.

136 STARTING AND DRIVING Sun Visors 2. Vanity Mirror (if available) Vanity mirror is provided on the back of the front passenger side sun visor.

3. Light for Vanity Mirror (if available) It is provided beside the vanity mirror. Light glows ‘ON’ as soon as flap of vanity mirror is open.

1. Mirror Flap 2. Vanity Mirror 3. Light for Vanity Mirror 1. Mirror Flap (if available) The sun visors can be pulled down to block the glare coming through the windshield. To block the glare from side windows: Pull down the sun visor and release it from retainer. Swing the sun visor to the side. 137 STARTING AND DRIVING

Steering Wheel Adjustment 3. Adjust the steering wheel to the de- NOTE sired position by moving steering (if available) When adjusting the steering wheel in axial and radial direction wheel, make sure that: (telescopic & tilt).  You can operate control pedals without any obstacles.  You can see all the displays in the instrument cluster clearly.

WARNING  Before starting off, make sure that the steering wheel position is locked.  Never unlock or adjust the steer- You can adjust the steering wheel posi- ing wheel while the vehicle is in tion to suit your convenience. motion. The release lever is located under the 4. Push release lever up completely to steering column. lock the steering column. 5. Make sure that steering wheel is se- To Adjust the Steering Wheel curely lock by checking up and down 1. Adjust the seat to a comfortable po- direction. sition.

2. Pull down release lever completely to unlock the steering column.

138 STARTING AND DRIVING Steering Lock and Ignition Switch ACC - Accessories such as the infotain- Starting and Stopping (without (if available) ment system can be operated, but the PEPS) engine remains ‘OFF’. Steering gets unlocked. Manual Transmission (MT) Starting the Engine ON - This is the normal operating position. All electrical systems are ‘ON’. Make sure that parking brake is engaged and vehicle is in neutral gear. START - Turn the key further clockwise to the START position, (spring loaded) to Press the clutch pedal fully and crank start the engine. As soon as the engine the engine. Do not press the accelerator starts, release the ignition key, which re- pedal while starting the engine. turns to ON position. While cranking, all accessories will be momentarily ‘OFF’. NOTE

Illuminated Key Ring (if available) The Starter protection sys- The ignition switch has the following four tem fitted in this vehicle positions: When the vehicle is unlocked, the illumi- does not allow you to crank nated key ring glows up. This helps to lo- the engine until you fully LOCK - This is the normal parking posi- cate ignition switch in the dark. press the clutch pedal. tion. Key from lock can be removed in this position only. NOTE Release the key as soon as the engine “LOCK” position prevents normal use of The engine can only be started starts. Repeat if engine does not start. the steering wheel after the key is re- when the gearshift lever is in “N” moved. position with the clutch pedal firmly pressed. To release the steering lock, insert the key and turn it clockwise to one of the other positions. 139 STARTING AND DRIVING

NOTE Starting Off WARNING The Starter protection system To start off, press the clutch pedal fully  A quick burst on the accelerator switches off the starter when it is and shift into first gear. before turning off the engine continuously cranked for more After releasing the parking brake, gradu- serves no practical purpose, it than 10 secs. In such a case, get ally release the clutch and slowly press wastes fuel and can damage tur- the key back to ‘OFF’ position & the accelerator. bocharger. wait for 30 secs.  Do not switch off the engine NOTE when it is running at high speed. WARNING When shifting or starting off, do not This will lead to premature turbo- race the engine. Racing the engine charger bearing wear.

The engine emits poisonous ex-

haust gases such as carbon mon- can shorten engine life and affect oxide. Inhaling these exhaust smooth shifting. gases leads to poisoning. There is Stopping the Engine a risk of fatal injury. Therefore, never leave the engine running in Turn the key to ‘ACC’ position to switch enclosed spaces without sufficient off the engine. Before switching off the ventilation. engine, run the engine in idle condition for at least 30 seconds and then switch NOTE off. This will allow the engine oil to lubricate the turbocharger, till its speed is After starting, run the engine in fully reduced and also allow the unit to idle speed for at least 30 seconds. cool down. Do not press accelerated pedal while starting the engine to avoid damage to turbocharger.

140 STARTING AND DRIVING

Gear Shifting and Driving NOTE Reverse Gear  Press the clutch fully when gear shifting. The reverse gear should be engaged only when the vehicle is stationary. Wait for 5 seconds after declutching to ensure smooth engagement of the reverse gear.  Do not press clutch pedal while driving the vehicle or when stationary on a slope.  When vehicle is in ACC/IGN/RUN mode and user The gearshift pattern is as shown on the does any door state transition For engaging reverse gear, lift the latch gear lever knob. Gear shifting should al- including tailgate and if PEPS and keeping latch lifted, shift to reverse ways be done with clutch pedal pressed does not detect smart key inside position. the vehicle when last door in- NOTE cluding tailgate is closed, then WARNING  Gear recommendation is dis- audio warning chime comes ON.  Never run the vehicle out of gear played when the clutch pedal is and coast down a hill. This is ex- in fully released position. tremely hazardous. Always run  If “F” is displayed in DIS of in- the vehicle in gear. strument cluster, it means  Slow down before shifting to a

‘Fault’ condition. Contact a TATA lower gear. This will help avoid MOTORS Authorized Service over-revving the engine, which Centre. can cause damage. 141 STARTING AND DRIVING  Be ensure the vehicle is com-  Never press the brake pedal and take advantage of the engine braking ef- pletely stopped before you put- the accelerator pedal at the fect and helps avoid overheating and ex- ting into reverse gear. It may same time. cessive wear of the brakes. cause damaged to the transmis- Automatic Transmission (if availa- sion. If you have driven for a long time in heavy rain without braking, there may be ble) Braking a delayed reaction from the brakes when braking for the first time. This may also Your vehicle has power-assisted brakes. occur after the vehicle has been The distance needed to bring the vehicle washed. to a halt increases with the speed of the Brake performance may become poor vehicle. Start applying brake anticipating and unpredictable if brakes are wet. the distance and slow down gradually. After driving through water or washing WARNING the underside of the vehicle, test the  Never use the brake pedal as a brakes while driving at a slow speed to footrest. see if they have maintained their normal  If you rest your foot on the brake effectiveness. If the brakes are less ef- pedal while driving, the braking fective than normal, dry them by repeat- The Automatic transmission has 6 for- system can overheat. This in- edly applying the brakes while driving ward and one reverse gear. The individ- creases the stopping distance slowly until the brakes have regained ual gears are select automatically, de- and can even cause the braking their normal effectiveness. pending on position of gear shift lever. system to fail. There is a risk of Braking on downhill gradients Starting Off an accident. On long and steep gradients, you must To start off depress the brake pedal fully reduce the load on the brakes by shifting and release the parking brake. Press the early to a lower gear. This allows you to 142 STARTING AND DRIVING

shift lock button on the knob of gear se- Reverse (R) handle of the selector lever and at the lector lever and move the lever from This position puts the same time press the brake pedal fully. Parking (P) mode to Drive (D) mode. transmission in reverse Manual/Sport mode (M/S)

Park (P) gear when engaged in stationary condition with This display shows vehicle Use Park (P) position is in Manual/Sport mode. when starting the engine brake pedal fully pressed. or parking the vehicle. Ap- The selector shall never This position allows the ply the parking brake be moved into reverse while driving for- driver to switch to activate whenever the vehicle is to ward. Manual mode to select be parked. gears like a manual gear-

Neutral (N) box. The selector lever must be engaged in The transmission is in Park (P) position only when the vehicle is Pressing the shift lever towards left side Neutral position. stationary. DO not engage Parking Posi- while in Drive mode will put the transmis- tion (P) in running condition. It enables the engine to sion in Manual mode. start and operate without If engaged while the vehicle is in motion The gear selector moves freely between driving the vehicle. it may severely damage the transmis- the Manual (M) and Drive (D) positions. As soon as shifter is moved forward or sion. Drive Mode (D) backward, the Manual (M) mode is acti- This position is for normal Before leaving the driver's seat, always vated. make sure the shift lever is in the P driving conditions for (Park) position; then apply parking brake maximum efficiency and It is possible to shift from D mode to fully and shut the engine off. If this is not fuel economy. It should be Manual mode and vice versa at any time followed, Unexpected and sudden vehi- used as often as possible. during driving. cle movement can occur. To move the selector to D To return back to Manual mode if it has mode; press the Shift lock button in the been selected; move the selector lever 143 STARTING AND DRIVING to Drive mode (by tapping the lever to- slows down. 1st gear is automatically se- Shifting sequence will get ad- wards right) and engage it again to M lected when the vehicle stops. justed after few shift cycle by TCU mode. In Manual/sports mode, when the en- (Transmission Control Unit). gine rpm approaches the intended lim- If Manual mode is selected, 1st gear must be used for moving off from sta- its, upshift will be made automatically by tionary condition. varying the shift points. In sports mode, only the 6 forward gears NOTE can be selected. To reverse or park the  Transmis- vehicle, move the shift lever to the R (Re- sion Control verse) or P (Park) mode as required. Unit may dis- ‘+’ For Upshifting in Manual mode allow incorrect manual shift com- Push the gearshift lever to the “+” direc- mand by user and a message tion and release it. Every time the lever ‘Driver Control Shift denied’ is dis- is operated, upshifting takes place one played on Instrument Cluster. step at a time in the order of 1st > 2nd >  In order to protect the engine, the 3rd > 4th > 5th > 6th gear. transmission will automatically ‘−’ For Downshifting in Manual mode upshift to prevent engine over-revving OR downshift to prevent en- Pull the gearshift lever to the “–” direc- gine stalling at certain specified tion and release it. Every time the lever engine rpm limits. is operated, downshifting takes place in the or-der 6th > 5th > 4th > 3rd > 2nd > 1st  The first few shifts on a new vehi- gear. cle, maybe somewhat abrupt after TCU replacement or software up- In Manual/sports mode, downshifts are dation. This is normal condition. made automatically when the vehicle 144 STARTING AND DRIVING Shift Lever -Manually Unlock Process (park) mode to other mode with the brake pedal depressed, below steps to be followed:

1. Apply the parking brake first.

2. Carefully squeeze & remove the bellow (1) by pulling it in upward direction as shown in area by arrows

(shown in fig. ) 1 3. Press & hold the release button (2) provided on shifter housing till you Fig 1 move the shift lever from P (park) mode to other mode by simultaneously pressing the knob button (3). (Shown in fig.2) 4. Carefully insert the bellow lugs (4) & snap fit in console cutout (5) highlighted as dotted area. (shown in fig.2) 5. Ensure the system is inspected by authorized dealer or service partner. Fig 2

When vehicle is in ON condition and shift lever is locked/cannot moved from P

145 STARTING AND DRIVING Automatic Gear Shifter Lever Movement and Conditions Driver Intervention for Shift Lever Position Movement Brake Pedal Driver Shift

P ->>R

R->>N Not required Not required

N->>D Not required

D->>M/S Not required Not required

Not required M/S->>D Not required

146 STARTING AND DRIVING

Driver Intervention for Shift Lever Position Movement Brake Pedal Driver Shift

D->>N Not required Not required

N->>R Not required

R->>P Not required

Brake Pedal Pressed Shifter Lever Knob Pressed

147 STARTING AND DRIVING

NOTE WARNING Shift Lock System  Before engaging in any mode (P-  To avoid damage of transmis- For your safety, the automatic transmis- R-N-D), Apply brake first then sion, do not accelerate the en- sion has a shift lock system which pre- knob button to be pressed for gine in R (Reverse) or any for- vents shifting the transmission from P safety reason. ward gear positions with the (Park) into R (Reverse) unless the brake  Before selecting the ‘M’ mode brakes ON. pedal is depressed. (manual mode), Ensure shift  When stopped on an incline To shift the transmission from P (Park) lever is placed in D mode first. roads, Use the service brake or into R (Reverse): Then engage M mode smoothly the parking brake, do not hold & vice versa. This sequence to be the vehicle stationary with en- 1. Press and hold the brake pedal. followed to ensure safety of sys- gine power. 2. Start the engine or turn the ignition tem.  Do not shift from N (Neutral) or P switch to the ON position. (Park) into D (Drive), or R (Re- 3. Move the shift lever to R mode. verse) when the engine is above If the brake pedal is repeatedly de- idle rpm.  Always shift the gears inline in pressed and released with the shift lever in the P (Park) position, a chattering sequence of (P-R-N-D). Do not try to shifts abruptly. noise near the shift lever may be heard. This is a normal condition.

148 STARTING AND DRIVING

WARNING  Optimum vehicle performance Always depress the brake pedal fully, and fuel economy is obtained by before and while shifting out of the P smoothly depressing and releas- (Park) mode into another position. ing the accelerator pedal. This is to avoid unintended motion of the vehicle which could injure the passengers inside or around the vehicle.

NOTE

Good Driving Practices (AT)

Never move the shift lever from P  (Park) or N (Neutral) to any other position with the accelerator pedal depressed.  Never move the shift lever into P (Park) when the vehicle is in motion.  Be ensure the vehicle is completely stopped before shifting into R (Reverse) or D (Drive).  Always use the parking brake. Do not depend on placing the transmission in P (Park) to keep the vehicle from moving. 149 STARTING AND DRIVING

Starting and Stopping (PEPS) NOTE with valid smart key near Immobilizer an- (If available) tenna (located below front cup holder).  If Smart key is inside the vehicle Engine Passive Start/Stop and on pressing start stop switch, if start stop switch green LED blink for 10 sec. duration then rotate steering wheel and simultaneously press start stop switch again.  If smart key is inside the vehicle and on pressing start stop switch, if start stop switch green LED blinks more than 10 sec. duration then contact authorized TATA MOTORS dealer. Emergency Start  If ESCL (Electronic Column Steer- ing Lock) is not unlocked Start/Stop switch is provided on the If vehicle engine is switched from ON to properly, then vehicle doesn’t go OFF and Start Stop button is pressed dashboard towards the right side of into ACC mode steering wheel. with clutch press within 5 sec, Engine Backup Start gets cranked. Start / Stop Switch If smart key battery voltage is low or NOTE A Start Stop Switch (SSSW) or Push to empty and vehicle is in OFF mode then If ESCL (Electronic Column Steer- Start Button is a main component of Pas- to start the engine user needs to press sive (Engine) Start and Stop system. It is ing Lock) is not unlocked properly, start/stop button two times with interval then Engine will not get cranked. used to control ACC, IGN outputs as well of 2.5 sec. between two switch press af- as to start and stop the engine. ter pressing the clutch pedal OR brake 150 STARTING AND DRIVING  Single Press Start: system can be used. Steering is un- 4. Limited display on instrument cluster locked. will be ON and steering will be un- 1. Bring the smart key with you and sit locked. Engine remain OFF. in the driver seat. b) Step 2 b) Step 2 2. Press the clutch pedal and then 1. Press the clutch pedal and then press the start-stop switch. press start-stop switch to start the 1. Press the start-stop switch without engine. pressing clutch pedal again. 3. Green colour LED on start-stop switch will turn ON. 2. Green colour LED on start-stop 2. Green colour LED on start-stop switch will turn ON. switch will turn ON. 4. Once engine starts successfully, green colour LED on start-stop switch 3. Once engine start successfully, 3. Engine will remain OFF and all elec- will remain ON. green colour LED on start-stop switch trical equipment and infotainment will remain ON. system can be used.  Two Step Start:  Three Step Start: c) Step 3 a) Step 1 a) Step 1 1. Press the clutch pedal and then 1. Bring the smart key with you and sit press start-stop switch to start the in the driver seat. 1. Bring the smart key with you and sit engine. in the driver seat. 2. Press the start-stop switch without 2. Green colour LED on start-stop pressing clutch pedal. 2. Press the start-stop switch without switch will turn ON. pressing clutch pedal. 3. Amber colour LED on start-stop 3. Once engine started successfully, switch turns ON. 3. Amber colour LED on start-stop green colour LED on start-stop switch switch will turn ON. 4. Engine will remain OFF and all elec- will remain ON. trical equipment and infotainment

151 STARTING AND DRIVING Option I  IGN relay turns OFF, ACC relay re- Manual Transmission (MT) mains ON. Passive Stop / OFF -Single Press Starting the Engine Stop:  Amber colour LED on start-stop Make sure that parking brake is en- switch turns ON.  IGN is ON and engine is running. gaged and vehicle is in neutral gear. WARNING  Customer presses start-stop switch Press the clutch pedal fully and crank with clutch pedal When vehicle is in OFF mode ( ACC, the engine. Do not press the accelerator IGN and Crank OFF) and user tries pedal when starting the engine.  ACC and IGN relay turns OFF. to lock the vehicle from outside by pressing any door handle switch NOTE  LED on start-stop switch turns OFF. and if PEPS detect smart key left The Starter protection system fit- inside the vehicle, then audio Option II ted in this vehicle does not allow warning / chime comes ON. you to crank the engine Emergency Stop / OFF -Single Long until you fully press the Press Stop: clutch pedal.  IGN is ON and engine is running Release the key as soon as the engine starts. Repeat if engine does not start.  Vehicle is in running condition i.e. wheel rpm >10 RPM or wheel sensor faulty.

 Customer does long press of start- stop switch i.e. pressed for more than 3 seconds

152 STARTING AND DRIVING

NOTE  When vehicle is in ACC/IGN/RUN  Do not switch off the engine The Starter protection system mode and user does any door when it is running at high speed. switches off the starter when it is state transition including tailgate This will lead to premature turbo- continuously cranked for more and if PEPS does not detect charger bearing wear. smart key inside the vehicle than 10 secs. In such a case, get Starting Off the key back to ‘OFF’ position & when last door including tailgate is closed, then audio warning To start off, press the clutch pedal fully wait for 30 secs. chime comes ON. and shift into first gear. After releasing the parking brake, gradu- WARNING Stopping the Engine ally release the clutch and slowly press The engine emits poisonous ex- Press the start stop switch to switch off the accelerator. haust gases such as carbon mon- the engine. Before switching off the en- NOTE oxide. Inhaling these exhaust gine, run the engine in idle condition for gases leads to poisoning. There is at least 30 seconds and then switch off. When shifting or starting off, do not a risk of fatal injury. Therefore, This will allow the engine oil to lubricate race the engine. Racing the engine never leave the engine running in the turbocharger, till its speed is fully re- can shorten engine life and affect enclosed spaces without sufficient duced and also allow the unit to cool smooth shifting. down. ventilation.

WARNING NOTE  A quick burst on the accelerator  After starting, run the engine in before turning off the engine idle speed for at least 30 sec- serves no practical purpose, it onds. Do not press accelerated wastes fuel and can damage tur- pedal while starting the engine to bocharger. avoid damage to turbocharger.

153 STARTING AND DRIVING Gear Shifting and Driving Reverse Gear  Press the clutch fully while shifting the gear. The reverse gear should be engaged only when the vehicle is stationary. Wait for 5 seconds after declutching to ensure smooth engagement of the reverse gear.  Do not press clutch pedal while driving the vehicle or when stationary on a slope

WARNING The gearshift pattern is as shown on the For engaging reverse gear, lift the latch  Do not switch off the ignition gear lever knob. Gear shifting should al- and by keeping latch lifted, shift to re- while driving. ways be done with clutch pedal pressed. verse position.  If you switch off the ignition while driving, safety-relevant functions NOTE are only available with limitations, or not at all. This could af-  Gear recommendation is displayed when the clutch pedal is fect the power steering and the

in fully released position. brake boosting effect. You will require considerably more effort to  If “F” is displayed in DIS of instru- steer and brake. There is a risk of ment cluster, it means ‘Fault’ an accident. condition. Contact the TATA MO- TORS Authorized Service Centre.

154 STARTING AND DRIVING

NOTE Recommended Driving Precau-  If you rest your foot on the brake You may notice a noise from trans- tions: pedal while driving, the braking mission under certain circum-  Shift to lower gear as per gear- system can overheat. This in- stances. This noise is normal and shift indicator (GSI) on cluster. creases the stopping distance and can even cause the braking is not an indication of a problem  To start-off (marching/ drive with your clutch or transmission. system to fail. There is a risk of away), always engage in first an accident. This noise may be noticed when gear. vehicle is idling in NEUTRAL condi-  Never press the brake pedal and While down shifting (from rd to tion with the clutch engaged  3 the accelerator pedal at the nd gear) at low engine RPM’s (clutch pedal released) or when 2 same time. (below rpm) press acceler- the transmission is warm. It may 1000 ator pedal to provide required If you have driven for a long time in also be heard while driving. rpm. heavy rain without braking, there may be a delayed reaction from the brakes when NOTE Braking braking for the first time. This may also occur after the vehicle has been  Your vehicle is equipped with Your vehicle has power assisted brakes. Dual Mass Flywheel (DMF), washed. which plays important role in The distance needed to bring the vehicle Brake performance may become poor providing refined powertrain / to a halt increases with the speed of the and unpredictable if brakes are wet. driveline experience. vehicle. Start applying brake anticipating  Driving at very low engine speed the distance and slow down gradually. After driving through water or washing is likely to stall the engine, espe- the underside of the vehicle, test the cially when driven without any WARNING brakes while driving at a slow speed to accelerator pedal inputs.  Never use the brake pedal as a see if they have maintained their normal footrest. effectiveness. If the brakes are less effective than normal, dry them by repeatedly applying the brakes while driving 155 STARTING AND DRIVING slowly until the brakes have regained Driving If the wheels start to slip within few feet their normal effectiveness. of the end of the climb, motion can be Climbing Sharp Gradients on Loose maintained by swinging the steered Braking on Downhill Gradients Surfaces wheels left and right, thereby providing On long and steep gradients, you must Start off smoothly in a suitable gear. Ac- increased grip. celerate smoothly so that there is no loss reduce the load on the brakes by shifting If the vehicle stalls or losses headway of traction by over-revving of the engine. early to a lower gear. This allows you to while climbing a steep hill, make a quick take advantage of the engine braking ef- Choose a slope as smooth as possible shift to reverse and allow the vehicle to fect and helps avoid overheating and ex- and select the appropriate gear so that move back with the control of engine cessive wear of the brakes. gear changing in the middle of the climb compression. is not required. WARNING Descending Sharp Gradients Changing gears in the middle of the  Do not shift to lower gear on a Depending on the severity of the gradi- climb can cause loss of momentum and slippery road surface in an at- ent, shift into appropriate gear. Use en- engine stalling. Shifting to lower gear tempt to increase the engine's gine braking judiciously without over-rev- has to be done cautiously to avoid loss braking effect, the drive wheels ving the engine. could lose their grip. of traction. Brake application under such situations  There is an increased danger of Under no conditions should the vehicle should be done very. skidding and accidents. be moved diagonally across a hill. The danger is in loss of traction and sideways WARNING slippage, possibly resulting in toppling over. If unavoidable, choose as mild an When descending on sharp gradi- angle as possible and keep the vehicle ents, NEVER turn the ignition key to moving. the ‘OFF’ position. Emission control system damage may result.

156 STARTING AND DRIVING Stopping the Vehicle Parking Brake Parking Brake Applied Turn the key to ‘ACC’ position to switch Mechanical parking brake acting on the off the engine. Before switching off the rear wheels is provided on the vehicle. engine, run the engine in idle condition for at least 30 seconds and then switch off. This will allow the engine oil to lubricate the turbocharger, till its speed is fully reduced and also allow the unit to cool down.

WARNING A quick burst on the accelerator before turning off the engine serves absolutely no practical pur- To apply the parking brake, hold the pose, it wastes fuel and can dam- lever as shown in above figure with age turbocharger. Parking Brake knuckle facing towards vehicle front and

pull the lever.

WARNING WARNING Do not switch the engine off when Do not press the button, while ap- it is running at high speed. This will plying parking brake. lead to premature turbocharger bearing wear.

157 STARTING AND DRIVING Parking Brake Released Mechanical parking brake acting only on  Block the wheels and engaged in the rear wheels is provided on the vehi- gear if parked on a slope. cle. To apply the parking brake, pull the lever up fully. The parking brakes tell- NOTE tale illuminates on the instrument clus- When parking on a downhill gradi- ter. To release it, pull the lever up ent, place the gear lever in slightly, press the release knob and push ‘Reverse’ position. While parking the lever down. Parking brakes tell-tale on uphill gradient, place the gear on the instrument cluster will turn ‘OFF’ lever in the ‘1st’ position. when the lever is fully released. WARNING Vehicle Parking Never leave children unsupervised  Park the vehicle in a safe place. in the parked vehicle. They could To release parking brake, hold the lever  Apply the parking brake. also operate the vehicle's equipment. There is a risk of an accident and pull the lever up slightly, press the  Engage the gear shift lever in Park (P) knob with the help of middle and ring fin- and injury. mode. ger as shown in figure and release the parking brake.  Ensure that all window glasses are closed and all lamps are turned

NOTE ‘OFF’.

Apply the parking brake properly  At night, put on the parking lights if before leaving the vehicle and re- required.

lease it before moving the vehicle.  Remove the key from the vehicle and lock the vehicle.

158 STARTING AND DRIVING

NOTE Reverse Park Assist Reverse Park Assist with Sensor Do not use parking brake for brak- (if available) ing unless unavoidable circum- The user can view the Park assist screen stances like when service brake is by selecting this feature in Infotainment not working properly. The braking display to see any obstacle behind the distance is considerably longer vehicle while parking. and the wheels could lock. There is an increased danger of skidding and accidents.

WARNING During parking, Ensure that Vehi- cle should not be keyed off in D The system also displays the Park assist mode. Operation screen when the reverse gear is engaged. The reverse park assist system can also be activated manually through infotain- It provides audio and visual information ment screen. Display will be seen on in- through the vehicles infotainment sys- fotainment screen. tem / Buzzer. Always look at surrounding before initiating reverse parking for kids, NOTE pets and elderly people moving around Turning the ignition ‘OFF’ ‘while the vehicle. the Park assist feature in running would disable the feature.

159 STARTING AND DRIVING

Reverse Park Assist Limitations should use extreme caution while WARNING parking the vehicle. Reverse Park Assist system is not a colli- Due to any reason, if the sensor sion avoiding system. It is solely the  If height of the bumper is changed gets misaligned or loses its in- due to alteration to the suspension or driver’s responsibility to park the vehicle tended fitment position, contact other causes. safely. your dealer for refitment.  If the sensor areas are extremely hot Reverse Park Assist feature works on ul- from direct sunlight or cold due to tra sound echo technology, due to which freezing weather. NOTE performance is not guaranteed in follow-  If Sensors are covered by a hand, Turning the ignition ‘OFF’ ‘while ing scenarios: sticker, accessory, etc. the Park assist feature in running would disable the feature.  If the object has a sharp edge sur-  If ultrasonic noise is present around face, where surface may divert ech- Vehicle due to other vehicle sensors, oes from sensor reception. horn, engine, air braking system WARNING (large vehicles), Exhaust Fans, Wire-  If object is mesh fence made up of 0 to 25 cm obstacle detection per- less transmitters or mobile phones. thin wires, where echoes can’t be formance is not guaranteed due to given by the surface.  If the vehicle speed exceeds 10 ultrasonic sensor technology limi-  Fast moving objects passes in the km/h, the system will not warn you tation. sensor field of detection, where ech- even though objects are detected, er- oes are not processed by the system. ror message 'Vehicle Speed is high, drive slowly!' will appear.  If object is made/covered by foam or sponge or snow where ultrasonic  Driving on uneven road surfaces e.g. sound signals are absorbed. Gravel, unpaved roads, Artificial Speed Breakers, or gradient.  Objects close to the rear bumper can go undetected by the Reverse Park Assist field of detection. Driver 160 STARTING AND DRIVING

Reverse Park Assist System Pre-  In case of damage of the rear Park Assist Malfunction Indications ventive Maintenance/Cleaning portion of the vehicle, Reverse In case of Reverse park assist system 1. Regularly clean the Sensors and Park Assist sensors position malfunctions, the following screen may keep them free from dust, ice, mud, may change which causes appear on the infotainment system. water, chewing gum etc. for proper wrong visual information on dis- Reason for this fault may be working of the system. Use a smooth play. In case of damage, make cloth for cleaning. sure that, Reverse Park Assist a. Body Control Module Failure sensors are fitted properly at the 2. Do not use water at high pressure for intended location. b. Sensor Malfunction cleaning the sensor.  In case of uneven road condi- c. Partner components such as Info- 3. Do not cover the sensors. This will in- tions or up-hill or downhill condi- tainment music system, Instrument terrupt park assist performance. tions, do not depend on Reverse Cluster failure. Park Assist aid.

4. Do not remove mud, snow on the  Do not apply any kind of force on sensors using stick or hard material. the reverse park assist sensors. Use normal water and soft cloth.

WARNING  In low light conditions, the screen may darken or image

may appear faint.  If the tire sizes are changed, the position of the fixed guidelines displayed on the screen may change.

161 STARTING AND DRIVING Rear Park Assist with Camera (If available)

Display screen Three color moving grid lines guide the user to understand the rear object distance exactly. The grid lines are updated by the motion of the vehicle as well as by the steering input.

Guidelines will help you to rightly find the

sufficient parking place, helps you to Rear View Camera is a visual reverse keep the vehicle straight, rear object guiding system. When reversing or park- proximity indication etc. ing, make sure that there are no persons, animals or objects in the area in NOTE which you are reversing. Turning the ignition ‘OFF’ ‘while the Park assist feature in running would disable the feature.

162 STARTING AND DRIVING Audio Warning Audio warning may come from Infotainment system speaker or through Buzzer, depending on vehicle model and configura- tion. Distance Range from Audible Infor- Visual Information Bumper (in mation cm) All six zones are highlighted (Red, Continuous 25 – 50 Green and Yellow Beep zones) Activation Bottom four zones are highlighted (Yel- Reverse Gear 51 – 100 Fast Beep low and Green This System will activate, if reverse gear is engaged. zones) Bottom two zones Deactivation 101 – 150 are highlighted Slow Beep (Green zones) System will deactivate, if reverse gear is disengaged, or park assist button (if available) is pressed

163 STARTING AND DRIVING Understanding Guidelines Indica- Green Line Do’s and Don’t tion Indicates, if rear object is in this colored  As the camera is, IP protected, do not zone, you have to be cautious. Still you detach, disassemble or modify in any can go backward safely. manner from the actual position. This will show required visual infor- Yellow Line mation in display. Indicates, if rear objects are in this col-  Do not use camera when tailgate is ored zone, you have to take utmost care. open. If tailgate is open, visual infor- However, objects fall in this zone, may mation may not be the actual rear not hit vehicle. view of the vehicle & system will warn with message 'Tail Gate Open, Static guidelines Red Line Please close. Indicates, if rear objects are in this col-  When the camera is operated under ored zone, you have to stop the vehicle fluorescent lights, sodium light or and not allowed to go backward. If you mercury light etc., illuminated areas still go backward, your vehicle will hit the on the lens may appear to flicker in object. the display.  Do not attach any advertisement or styling or any kind of stickers on top of camera. If this happens, camera cannot provide you the visual image Dynamic guidelines and may damage camera.  Do not add any accessory, which will obstruct camera field of view.

164 STARTING AND DRIVING Cleaning Camera 7. Do not remove mud, snow on the  The camera used in the vehicle, camera lens using stick or hard ma- may not reproduce the same 1. Due to environmental reasons, dust, terial. Use normal water and soft color of the real object. mud or fog may accumulate on the cloth. camera lens. So regularly clean the  In case of damage of the rear camera lens. WARNING portion of the vehicle, camera position may change. Which Use water to clean the camera lens. 2.  The camera uses fish eye lens. causes wrong visual information Do not use extreme cold or hot water. So the size of the objects or in on display. In case of damage, Rapid changes in temperature may the display may differ from the make sure that, camera is fitted brittle the camera lens. Do not apply actual size and distances in low properly at the intended location. High Pressure water for cleaning. light conditions, the screen may  In case of uneven road condi- 3. Wipe the camera lens with soft cloth. darken or image may appear faint. tions or up-hill or downhill condi- 4. Do not use hard cloth or material to tions, do not depend on rear view wipe the camera lens. This will cause  If the tire sizes are changed, the camera park aid. scratches on the camera, and leads position of the fixed guidelines displayed on the screen may  Do not apply any kind of force on to deteriorated visual image on the the camera. display. change. Always use rear View mirrors  During rainy conditions, image  Do not apply organic solvent, car 5. may get obscured. In such condi- along with Rear View Camera for wax, window cleaner or glass coat to tions, do not depend on camera confirming the safety of the rear clean the camera. If this is applied, view. The camera used in the ve- and the surrounding conditions. wipe it off as soon as possible. hicle, may not reproduce the  High humidity and variation in 6. Do not apply heavy force on lens, same color of the real object. ambient temperature may result while cleaning. into condensation inside the camera lens, which may further

165 STARTING AND DRIVING result into degradation of cam- Rear View Camera System Pre-  The area displayed on the screen era video feed on the screen. It is cautions may vary according to vehicle orien- recommended that not to rely on 1. Area Displayed on Screen tation conditions. camera video feed for parking The rear view camera system displays an  Objects, which are close to either cor- assistance in such scenario. This image of the view from the bumper of ner of the bumper or under the phenomenon is temporary and the rear area of the vehicle. To adjust the bumper, cannot be seen on the will be automatically recovered image on the rear view monitor system screen. with reduction in humidity and screen.  The camera uses a special lens. The less variation in ambient temper- distance of the image that appears ature. on the screen differs from the actual  The area displayed by the rear distance. The monitor may not dis- view camera is limited. The cam- play items that are located higher era does not display objects that than the camera field of view. are close to or below the bumper, underneath the vehicle, or ob- 2. When the Ground Behind the Ve- jects out of the camera’s field of hicle Slopes Up Sharply view. The area displayed on the screen may vary according to vehicle orientation or road conditions.

166 STARTING AND DRIVING 3. When the Ground Behind the Ve- The distance guidelines will appear to be hicle Slopes Down Sharply further from the vehicle than the actual distance. Because of this, objects will appear to be closer than they actually are. In the same way, there will be a margin of error between the guidelines and the actual distance/course on the road. 4. When Any Part of the Vehicle Sags The distance guidelines will appear to be closer to the vehicle than the actual distance. Because of this, objects will appear to be farther away than they actually are. In the same way, there will be a margin of error between the guidelines and the actual distance/course on the road.

When any part of the vehicle sags due to the number of passengers or the distribution of the load, there is a margin of error between the fixed guide lines on 167 STARTING AND DRIVING the screen and the actual dis- b. Vehicle Width Guidelines tance/course on the road. 5. When Approaching Three-dimensional Objects The distance guidelines are displayed according to flat surfaced objects (such as the road). It is not possible to deter- mine the position of three-dimensional objects (such as vehicles) using the distance guidelines. When approaching a three-dimensional object. Visually check the surroundings and the area behind the vehicle. On the screen, a. Distance Guidelines it appears that a truck is parked at point B. However, in reality if you back up to point A, you will hit the truck. On the screen, it appears that A is closest and C is furthest away. However, in reality, the distance to A and C is the same, and B is farther than A and C.

168 STARTING AND DRIVING

Visually check the surroundings and the Drive mode selection switches are pro- NOTE area behind the vehicle. In the case vided on center console for activation. shown below, the truck appears to be Press the switch to select the mode. When vehicle is in ECO or SPORT outside of the vehicle width guidelines mode, by pressing current mode ‘ECO ‘, ‘CITY’ and ‘SPORT’ drive modes and the vehicle does not look as if it hits switch again, mode will switch to are provided. These modes can be used the truck. However, the rear body of the CITY mode. truck may actually cross over the vehicle to adjust engine characteristics and vehicle performance in line with desired re- Terrain Response Mode (if availa- width guidelines. In reality if you back up quirement. ble) as guided by the vehicle width guidelines, the vehicle may hit the truck. Drive Performance Drive Mode (if available) Mode Increased engine Torque CITY and Power output for

BALANCED performance. It is default

mode. Optimum engine Torque ECO and Power output for FUEL EFFICIENT performance. SPORT Rotate the knob clockwise to select the Produce more torque terrain mode. from engine.

169 STARTING AND DRIVING 1. Normal Road Mode The wet mode is designed for driving in all customers specially novice or inexpe- In this mode vehicle performance opti- the rain. It is characterized by having bet- rienced user. mized to support, all surface condition. ter traction and handling so you can ef- NOTE Stopping distance progressively, in- fectively and safety drive during these creases with vehicle speed. Maintain a conditions. Cautiously drive the vehicle on a sufficient distance between your vehicle rough road or off the road. Other- NOTE and the vehicle ahead. wise, the tires and wheels may be For long distance driving, perform safety If you have driven for a long time in damaged. After driving those ar- checks before starting a trip and take wet road without braking, there eas, inspect the tires and wheels. may be a delayed reaction from rest at certain intervals to prevent fa- the brakes when braking for the 4. Electronic Stability Program tigue. first time. You have to depress the (ESP) (if available) 2. Wet Mode brake pedal more firmly. Maintain ESP monitors driving stabil- a greater distance from the vehicle ity and traction. On wet road or during light showers, “Aq- in front. uaplaning” can occur. “Aquaplaning” is If ESP detects that the vehicle is deviat- the loss of direct contact between the 3. Rough Road Mode ing from the direction desired by the road surface and the vehicle’s tires due Rough Road Mode optimizes the vehicle driver, one or more wheels are braked to to a water film forming between them. stabilize the vehicle. The engine output Steering or braking the vehicle can be behavior for driving over rough road or other unyielding obstacles. is also modified to keep the vehicle on very difficult, and loss of control can oc- the desired course within physical limits. cur. Braking performance is also tuned to ESP assists the driver when pulling away The best advice is to slow down when the support Rough road surfaces as com- on wet or slippery roads. ESP can also road is wet. pared to other drive modes. stabilize the vehicle during braking and acceleration. Activate the ESP feature by System allows improved rough road per-

pressing on the center console. formance to be more easily accessible to 170 STARTING AND DRIVING 5. Hill Descent Control (HDC) required (No press of HDC button is re- (if available) quired).HDC is permanently switched off if the vehicle speed exceeds 60 kmph While driving down on a hill and Active state on HDC switch will go off slope, activate the HDC fea- automatically. HDC works in both Neu- ture by pressing on the cen- tral and in Gear forward and reverse po- ter console. sition. HDC provides a smooth and controlled While driving down a hill, the engine hill descent by enabling the vehicle to braking should be used by shifting into a control the speed of each wheel. The lower gear. Do not drive in neutral gear system will automatically apply the or switch off the engine. brakes to slow down to the desired vehicle speed. Cruise control +/-buttons or WARNING Brake and accelerator pedal can be ad- HDC cannot take account of road, just the speed to a comfortable level. weather, traffic and tyre condi- HDC interventions will be automatically tions. You are always responsible disabled once the descent is complete for keeping control of the vehicle and vehicle is on levelled road. Non-zero and for assessing whether the speed less than 35 kmph would be re- downhill gradient can be man- quired to turn ON HDC. A speed greater aged. than 40 kmph will end all active HDC control and switch HDC to standby mode. Once the vehicle speed is lower than the specified threshold of 40 kmph HDC becomes activated again whenever

171

STARTING AND DRIVING

172 EMERGENCY AND BREAKDOWN ASSISTANCE Emergency Equipment Tool kit, Jack and Spare wheel Spare Wheel You should be familiar with the location of the emergency equipment provided in the vehicle and how to use it. Check this equipment periodically and ensure that they are in proper working condition and stowed at their locations. First Aid Kit The first aid kit is kept inside the glove box compartment.

The kit contains items that can be used in case of minor injuries only. Tool kit, Jack are provided in rear boot. Spare wheel removal spanner NOTE 1. Check contents of the first aid kit 2. Jack periodically and replenish con- 3. Reversible screw driver sumed or expired items. 4. Jack Handle 5. Wheel Spanner

173 EMERGENCY AND BREAKDOWN ASSISTANCE Advance Warning Triangle Spare Wheel Removal Process  To remove the spare wheel, open the tail gate.  Open the cover and take out the advance warning triangle.

Keep the warning triangle at an approxi-

mate distance of 50-150 m behind your An advance warning triangle is kept on vehicle in the same lane of traffic. The the tool tray in the luggage compart- reflecting side of the triangle should face ment. the oncoming traffic and it should be free from any obstacles. Use advance warning triangle to warn the approaching traffic in case of vehicle NOTE breakdown or during emergency, where  Open the flap with the help of screw your vehicle could become a potential After using the warning triangle tie driver provided in tool kit for access- traffic hazard. it firmly and keep it inside the bag ing to spare wheel removal retaining to avoid rattling noise. bolt. Press hazard warning switch, all turn signal lamps will start blinking.

174 EMERGENCY AND BREAKDOWN ASSISTANCE  Remove the holding bracket from the spare wheel and get the spare wheel separated.

 Insert the spare wheel removal span-  As the retaining bolt gets loosened, ner and rotate anticlockwise to un- the spare wheel lowers down as screw the retaining bolt. shown.

175 EMERGENCY AND BREAKDOWN ASSISTANCE Spare Wheel Fitment Process Hazard Warning Switch In Case of Flat Tyre Engage the holding brackets in spare   Reduce vehicle speed gradually, wheel. Avoid sudden steering movement or braking.  Pay attention to the traffic conditions as you do so.  Switch on the hazard warning lamps.  Stop the vehicle on solid, non-slippery and level ground, as far away as possible from traffic.  Use the Jack on level, hard ground. Avoid changing the wheel on uphill Press the hazard warning switch to acti- and downhill slopes. Chock the wheels, if the deflated wheel needs vate the hazard warning. All the turn sig- to be changed on slope / ghat area.  Insert the spare wheel removal span- nal lamps will flash simultaneously. To  If possible, bring the front wheels into ner and rotate clockwise to lift the turn OFF, press the switch again. the straight-ahead position. spare wheel. Use the hazard warning to warn the traf-  Secure the vehicle against rolling fic during emergency parking or when  Tighten the bolt until you heard the away. your vehicle could become a traffic haz- ‘Tak’ noise. Do not overtight.  Set the parking brake firmly and shift ard. into “R” (Reverse) gear on level NOTE NOTE ground and while vehicle is in down- While stowing the spare wheel, en- The hazard warning lamps can op- hill position. sure that winch bracket is properly erate even if the ignition is  When the vehicle is in uphill position, engaged in wheel slot. switched off. shift the gear in first gear. 176 EMERGENCY AND BREAKDOWN ASSISTANCE

 Switch off the engine. Changing Flat Tyre NOTE  Keep advance warning triangle at a Remove the center hub cap/wheel cover  The jack is designed only to raise suitable distance behind the vehicle in case of steel wheel rim (if available). and hold the vehicle for a short as an indication of breakdown. time while a wheel is being  Close all the doors. Loosen the nuts (as indicated) on the changed. It is not suited for per- wheel in diagonal sequence. Do not un-  Chock the wheels, shift the gear in to forming maintenance work un- ‘R’ (Reverse) on level ground and screw the nuts completely before jacking der the vehicle. while vehicle is in down hill position, the vehicle. and shift the gear in first gear when  Use the jack on level, hard vehicle is in uphill position. ground. Avoid changing the wheel on uphill and downhill WARNING slopes. Chock the wheels, if the deflated wheel needs to be If you drive with a flat tyre, there is changed on slope / ghat area. a risk of the following hazards:  Before raising the vehicle, se-  A flat tyre affects the ability to cure it from rolling away by ap- steer or brake the vehicle. plying the parking brake.  You could lose control of the vehicle.  Chock the wheels. Shift the gear  Continued driving with a flat tyre into 'R' (reverse) on level ground will permanently damage the tyre and while vehicle is in downhill and cause excessive heat Wheel nut removal position, and shift the gear in first gear when vehicle is in up- buildup and possibly a fire. There is a risk of an accident. hill position.  Do not use wooden blocks or similar objects as a jack under- lay. 177 EMERGENCY AND BREAKDOWN ASSISTANCE

 Do not place your hands and feet or lie under the raised vehicle when it is supported by a jack.  Do not run the engine when the vehicle is supported by the jack and never allow passengers to remain in the vehicle.  Do not open or close a door or the tailgate when the vehicle is raised. Jacking point location Assemble the Jack handle and wheel WARNING spanner (as shown in jacking fig). If you do not position the jack cor- Position the jack vertically and raise it by rectly at the appropriate jacking turning the jack handle clockwise until point of the vehicle, the jack could the jack sits completely on jacking point tip over with the vehicle raised. and the base of the jack lies evenly on There is a risk of injury. Jack may the ground. also get damage.

Jacking Point Location on Vehicle Continue to raise the jack slowly and The jacking points are indicated below smoothly until the tyre clears the ground. the door of the vehicle (Refer jacking Do not raise the vehicle more than nec- point location). essary.

178 EMERGENCY AND BREAKDOWN ASSISTANCE Remove wheel mounting nuts with the Place the flat tyre at spare wheel loca- help of wheel spanner and take out flat tion. tyre. NOTE NOTE Check and correct the tyre pres- Do not place wheel nuts in sand or sure and wheel nuts tightness of on a dirty surface. Do not apply oil the changed wheel at nearest au- or grease on it. thorised service station. Get the flat tyre repaired at the ear- Roll the spare wheel into position and liest.

align the holes in the wheel studs.

Jacking front wheel Install wheel nuts with their cone shaped WARNING end facing the wheel. Tighten each nut Do not jack the vehicle under rear by hand until the wheel is securely axle. seated on the hub.

Lower the jack completely then tighten the wheel nuts one by one using wheel spanner. Press fit the wheel cover back /center hub cap back (if available).

Restore all the tools and jack at their Jacking rear wheel respective location.

179 EMERGENCY AND BREAKDOWN ASSISTANCE Jump Lead Starting  Make the final connection (other end of the negative terminal) to an un- Use only a battery of same rating & ca- painted, heavy metal part (i.e. engine pacity to jump start your vehicle. Position mounting stud/nut) of the vehicle of the booster battery close to your vehicle discharged battery. so that the jump leads will reach both batteries. When using a battery of another vehicle, do not let the vehicles touch. Apply the parking brake firmly and keep the gearshift lever in neutral. Turn off all vehicle accessories, except Make jump lead connections as follows: those necessary for safety like hazard  Connect one end of the first jump warning lamps. lead to the positive (+) terminal of the If your vehicle is equipped with Battery discharged battery. sensor, then do not connect your jump start cable lead directly on the Sensor  Connect the other end to the positive  Start the engine of the vehicle with surface. Connect only on the negative (+) terminal of the booster battery. the discharged battery. cable surface as shown on the image. Af-  Connect one end of the second jump  Before disconnecting the jumper ca- ter jump start event, IAC function will be lead to the negative (–) terminal of bles, let the engine run for several restored only when the Vehicle is parked the booster battery. minutes. in idle for 3-4 Hours.

180 EMERGENCY AND BREAKDOWN ASSISTANCE

 If the booster battery you are using is WARNING there is sufficient ventilation fitted to another vehicle, start the en- while charging and jump-start- Never connect the jump lead di- gine of the vehicle with the booster ing. Do not lean over the battery. rectly to the negative (–) terminal battery. Run the engine at moderate  Make sure that the positive ter- of the discharged battery. This may speed. minal of a connected battery lead to an explosion. does not come into contact with  Remove the jump leads in the exact vehicle parts. Never place metal reverse order in which you connected WARNING objects or tools on a battery. them.  It is important that you observe Do not allow battery electrolyte to  the described order of the bat- come in contact with eyes, skin, NOTE tery terminals when connecting fabrics or painted surfaces. The Do not disconnect the discharged and disconnecting a battery. If fluid contains acid which can battery from the vehicle. you are in doubt, seek assistance cause injury and severe damage.

from qualified specialist work- Wear protective apparel. Do not shop. inhale any battery gases. Keep  Never connect or disconnect the children away from batteries. In battery terminals while the en- case if battery acid comes in con- gine is running. tact with the skin, wash it off immediately with water and seek medical attention.  During charging and jump-starting, explosive gases can escape from the battery. There is a risk of an explosion. Particularly avoid fire, open flames, creating sparks and smoking. Ensure 181 EMERGENCY AND BREAKDOWN ASSISTANCE

Towing WARNING Access to Tow Hook When towing a break down vehicle, cer-  Never get under your vehicle af-  Unscrew the screws (1) & (2) with the tain precautions and procedures must ter it has been lifted by a tow help of screw driver which is provided be taken to prevent damage to the vehi- truck. in Tool kit. cle and/or components. Failure to use  For towing a vehicle, the best way standard towing precautionary is to use a wrecker. Alternatively measures when lifting or towing a break use a rigid tow bar. down vehicle could result in an unsafe  Switch 'ON' the hazard warning operating condition. indicators of both the vehicles to warn other road users. To ensure proper towing and to prevent  Limit the speed to 20-30 kmph. accidental damage to your vehicle, take  In case of brake failure, use the help of a TATA MOTORS authorized parking brake to control the dealer or a commercial tow-truck ser- vehicle. vice.  Fasten the tow rope or tow bar at the towing eyes. Otherwise, the NOTE vehicle could be damaged. Make sure that the parking brake  When towing, pull away slowly is released; vehicle in neutral gear and smoothly. If the tractive position and steering wheel is un- power is too high, the vehicles locked. The power steering func- could be damaged. tions only when engine is running. Hence, during towing the steering efforts will be more.

182 EMERGENCY AND BREAKDOWN ASSISTANCE For removal of cover, pull the rear side Recommended Towing down. In case of break down, we recommend that your vehicle be towed with the driving wheels off the ground or place the vehicle on a flatbed truck as shown.

WARNING  Never tow your vehicle with the front wheels on the ground or four wheels on the ground (forward or backward), as this may For fitment of cover, cause serious damage to the transmission.

 Engage the front lugs first.  When towing with the rear  Slide the cover in rear direction to wheels on the ground or on tow-  Slowly press from both side to en- disengage front lugs. ing dollies, place the ignition gage side lugs. switch in the ‘ACC’ or ‘ON’ posi-  Then carefully disengage the side tion, and secure the steering lugs.  Engage rear lugs and then tighten the screws. wheel in the straight-ahead position with a rope or similar device. To avoid serious damage to automatic transaxle, limit the vehicle speed to 15 km/h (10 mph) and drive less than 1.5 k m (1 mile) when towing.

183 EMERGENCY AND BREAKDOWN ASSISTANCE Before towing, check the automatic Fuses Checking and Replacing Fuses transaxle fluid leak under your vehicle. If If any electrical unit in your vehicle is not the automatic transaxle fluid is leaking, Your vehicle has fuse boxes at two loca- functioning, check the fuses first. a flatbed equipment or towing dolly must tions. be used. The vehicles electrical circuits have Please follow the steps below that will fuses to protect the wiring from short cir- guide you to check and replace them. cuits or sustained overload.  Apply parking brake  Switch off all electrical accessories.  Turn the ignition key to the 'LOCK' position.  In the fuse box, identify the defective fuse from its melted wire.

1. Engine Compartment Fuse Box. 2. Cabin Compartment Fuse Box.  Remove the blown fuse by “fuse puller”. The fuse puller and spare fuses are provided in the engine compartment fuse box. 184 EMERGENCY AND BREAKDOWN ASSISTANCE

WARNING Battery Mounted Fuse  If you manipulate or bridge a faulty fuse or if you replace it with a fuse of higher amperage, the electric cables could be over- loaded. This could result in a fire. There is a risk of an accident and injury.  Always replace faulty fuses with the specified new fuses having Engine compartment fuse box the correct amperage.  Blown fuses must be replaced with fuses of same rating, which you can recognize by color and value.

NOTE Always ensure that the spare fuses are replenished.

 Ensure that all other fuses are pressed firmly in position.  If a newly inserted fuse also blows, have the cause traced and rectified at nearest TATA MOTORS Authorized Service Centre immediately. 185 EMERGENCY AND BREAKDOWN ASSISTANCE

Fuse Fuse To access the fuse box, follow the proce- Function dure as given below: No. Rating STARTER  Open the Engine compartment. PF1 250 A MOTOR  Remove the 2 screws of air intake cover (snorkel) with the help of screw WARNING driver provided in tool kit If Fuse box cover is removed for  Remove the snap fitted cover of fuse any reason, it should be refitted box. properly at its original position.

1. Engine Compartment Fuse Box NOTE The fuse box layout is for reference purpose only. Please refer the sticker provided inside the fuse box cover.

Fuse box located in Engine compartment near battery.

186 EMERGENCY AND BREAKDOWN ASSISTANCE

Fuses - Engine Compartment (Diesel)

187 EMERGENCY AND BREAKDOWN ASSISTANCE Fuse Fuse Function 20 BLOWER MOTOR 40 A Relay Relay No. Rating Relay Function 21 COOLING FAN FAST 60 A No. Rating 1 INTERIOR F/B BAT - I 60 A IGNITION MINI NO UNDERBONNET F/R R1 40A 22 30 A RELAY 2 EMS BATT 5 A BOX COOLING FAN LOW 23 REVERSE LAMP AT 5 A R2 40A 3 COMPRESSOR 10 A MINI NO RELAY HEAD LAMP HIGH 24 10 A COOLING FAN HIGH BEAM RH R3 70A 4 ATS 15 A MAXI NO RELAY HEAD LAMP HIGH HORN HIGH/LOW 25 10 A 5 15 A BEAM LH EMS ECU MINI NO TONE R4 40A HEAD LAMP LOW RELAY 26 10 A 6 ABS ECU 25 A BEAM RH STARTER SOLENOID R5 40A HEAD LAMP LOW MINI NO RELAY 7 SPARE --- 27 10 A BEAM LH STARTER INHIBIT R6 40A 8 EMS RELAY 40 A 28 EMS ECU - II 15 A MINI NO RELAY

9 BRAKE LAMP 5 A 29 EMS ECU - I 20 A R7 ---

10 FUEL PUMP 20 A 30 EMS ECU - III 10 A R8 --- 39 SPARE --- WIPER SPEED 11 DCU 15 A R9 SLOW/FAST MICRO 20A 12 TCU 15 A 40 EMS IGN 5 A (NO-NC) RELAY R10 --- 13 SPARE --- 41 ABS IGN 5 A REVERSE LAMP WIPER ON/OFF MI- 14 INTERIOR F/B BAT - II 60 A 42 5 A R11 20A (MT)/TCU (AT) CRO (NO-NC) RELAY 15 GLOW PLUG 60 A FRONT WIPER MO- ATS MICRO NO 43 30 A R12 20A TOR REALY 16 IGNITION LOAD 30 A 44 SPARE --- HEAD LAMP HIGH R13 BEAM MICRO NO 20A 17 ABS ECU 40 A 45 IBS 5 A REALY DCU MICRO NO RE- 18 COOLING FAN LOW 40 A 46 SPARE --- R14 20A LAY STARTER MOTOR 19 30 A 47 EMS-CRANK INPUT 5 A SOL 188 EMERGENCY AND BREAKDOWN ASSISTANCE HEAD LAMP LOW 1. Cabin Compartment Fuse Box R15 BEAM MICRO NO 20A REALY Cover Removal Procedure HORN MIRCO NO R16 20A RELAY Fuse box is located behind glove box. To FUEL PUMP MICRO R17 20A NO RELAY access the fuse box, remove cover as AC CLUTCH MICRO R18 20A per procedure given below: NO REALY 1. Remove snap fitted end-cover first.

3. Open glove box and remove complete assembly by removing highlighted 4 screws.

To remove the cover, gently pull the 2. cover from bottom side such that the lugs get disengaged.

189 EMERGENCY AND BREAKDOWN ASSISTANCE 4. Disconnect glove box lamp connec- 5. Disconnect glove box switch connec- 6. Pull out the fuse from fuse box mod- tion. tion. ules from available cutout as shown below.

190 EMERGENCY AND BREAKDOWN ASSISTANCE 7. Check the fuse of required function with help of fuse box sticker present at shown location.

8. If fuse is blown, replace with same

rating fuse from spare fuses in en-

gine compartment fuse box. 9. Fit back the glove box by following reverse procedure.

NOTE It is recommended to replace fuse at TATA Authorised service centre.

191 EMERGENCY AND BREAKDOWN ASSISTANCE Fuses - Cabin Compartment

192 EMERGENCY AND BREAKDOWN ASSISTANCE

Fuse Fuse Function AMPLIFIER 20A TAILGATE RELEASE 10A Rating CDL - LOCK PEPS 10A 20A IGN SUPPLY 10A MICRO NO-NC RELAY CDL - UNLOCK I. CLUSTER 5A 20A POWER SOCKET 15A MICRO NO-NC RELAY RESTRAINT CONTROL KEY-IN/ POWER SEAT 5A/ 20A TAILGATE RELEASE 10A 20A MUDULE ACC RELAY COIL/ SUN- MICRO NO RELAY 5A/ 20A IGNITION MIRROR ADJUST MOTOR 5A ROOF 20A TERRAIN RESPONSE MICRO NO RELAY 10A IMMO IGN/ PEPS IGN FEED- SWITCH REAR WIPER 5A 20A BACK MICRO NO RELAY USB CHARGER BSIV/ USB TRANSIT 10A 5A/ 10A POWER SEAT CHARGER BSVI 20A REAR WIPER 10A MICRO NO RELAY RELAY COIL/ PEPS ACC 10A/ 5A REVERSE LAMP 20A REAR BLOWER MOTOR 15A MICRO NO RELAY ACC BATT HIGH POWER 20A HEATED REAR WINDOW 40A PARK ASSIST 5A MINI NO RELAY BCM - I 15A BLOWER MOTOR W/W MTR DR DOOR 25A 40A IMMO BATT/ TPMS BATT 5A MINI NO RELAY ACCESSORY USB CHARGER 3RD ROW 5A 40A BCM - II 15A MINI NO RELAY CDL 15A INFOTAINMENT 20A

STARTER FEEDBACK 5A BCM - III 15A OBD/ ACC BATT LOW HRW 25A 15A POWER SUNSHADE/ BLOWER CON- 20A/ 5A HVAC BAT 10A TROLLER

193 EMERGENCY AND BREAKDOWN ASSISTANCE Bulb Specification

Sr. Description Rating Type Qty. No. 1 High beam + Low beam (Option I) 12V, 55W H7 4 High Beam : 12V, 55W High Beam : H7 2 High beam + Low beam (Option II) 4 Low Beam : 12V, 25W Low Beam : D5S 3 Turn Signal Front (Option I) 12V, 21W PY21W 2 4 Turn Signal Front (Option II) LED LED Module 2 5 Turn Signal Rear 12V, 21W PY21W 2 6 Fog Lamp Front (Option I) 12V, 19W H16 2 7 Fog Lamp Rear (Option II) 12V, 21W P21W 2 8 Stop Lamp LED LED Module 2 9 Position Lamp Front (Option I) 12V, 5W W5W 6 10 Position Lamp Front (Option II) LED LED Module 2 11 Position Lamp Rear LED LED Module 4 12 Reverse Lamp 12V, 16W W16W 2 13 Rear Registration Plate Lamp LED LED Module 2 14 Side Repeater Lamp on ORVM LED LED Module 2 15 High Mounted Stop Lamp (Option I) 12V, 5W W5W 5 16 High Mounted Stop Lamp (Option II) LED LED Module 1

194 EMERGENCY AND BREAKDOWN ASSISTANCE

Sr. Description Rating Type Qty. No. 17 Boot Lamp 12V, 5W W5W 1 18 Glove Box Lamp 12V, 5W W5W 1 19 DRL (If available) LED LED Module 2 20 Roof Lamp 1st Row LED LED Module 1 21 Roof Lamp 2nd Row LED LED Module 1 22 Door Ajar / Puddle Lamp 12V, 5W W5W 4

195 EMERGENCY AND BREAKDOWN ASSISTANCE 24 X 7 Road Assistance Response Time ** for the On Road  Explain your exact location with land- Assistance Program marks and tell us about the problem Dear Customer, you face with the vehicle. Within City It is our responsibility and our endeavor 60 minutes  Park your vehicle on the edge of the to ensure that you have our complete Limits road, open the bonnet and put on the service backup, wherever and whenever On State or Na- hazard warning signal. you need the same. When you have a tional High- 90 minutes  Place the advance warning triangle road network that spans wide area, the ways supplied with the vehicle approx. 3 m probability of a breakdown happening Ghat Roads from the vehicle in the direction of within hailing distance of a TATA MO- and other 120 minutes oncoming traffic. TORS Authorized Workshop is very low. places It is precisely for this reason, we have ** (The response time will depend on tied up with TVS AA, who will provide the location, terrain, traffic density and breakdown assistance including towing the time of the day.) to the nearest TATA MOTORS Authorized Workshop through their Authorized Ser- Standard procedure when calling vice Providers (ASP). for On Road Assistance in case of a breakdown: The 24X7 On Road Assistance Program shall be automatically available to your  Dial the toll free help line number – vehicle for the duration of Warranty pe- 1800 209 7979 riod. The program shall also be availa-  Identify your vehicle with the Vehicle ble, if you avail the same post warranty. chassis number that is available in the Owner’s Manual.

196 EMERGENCY AND BREAKDOWN ASSISTANCE Coverage under 24 X 7 on Road charges levied in relation to the vehi-  Cases involving accident, fire, theft, Assistance Program cle being towed to be paid by the cus- vandalism, riots, lightening, earth- tomers in actuals in cash). quake, windstorm, hail, tsunami, un- I. The 24x7 On Road Assistance Pro- usual weather conditions, other acts gram Service covers the following ser- For accident cases, towing charges of God, flood, etc. vices on your vehicle during warranty pe- to be borne by the customer. riod.  Vehicles that are unattended, un-reg- II. The 24x7 On Road Assistance Pro- istered, impounded or abandoned.  Wheel change through spare wheel. gram coverage on availing the 24X7 policy, post warranty is up to maximum of 6  Breakdown/defects caused by mis-  Arrangement of fuel. (Fuel cost will instance of assistance in one year for use, abuse, negligence, alterations be chargeable at actual cost) both the plans- Basic and Premium. In or modifications made to the vehicle.  Re-opening the vehicle in cases of the premium plan, this includes 2 in-  Lack of maintenance as per the key lock out. stances of towing up to the nearest TATA MOTORS authorised workshop. maintenance schedule as detailed in  Rectification of electrical problems the owner’s manual. related to battery, fuses etc. Exclusions  Cases involving racing, rallies, vehi- 24 X 7 On Road Assistance Program  On spot repairs for complaints repair- cle testing or practice for such does not apply to able at site. events.  Cost of parts consumables and la-

 Vehicle to vehicle towing or winching bour for such repairs not covered un- & towing for non-accident cases up der warranty*. These charges are to to the nearest TATA MOTORS author- be settled with ASP in cash. ized workshop. Towing charges at actual cost beyond the same to be paid  Toll or ferry charges paid by ASP in to the ASP in cash. (Any ferry or toll reaching to the breakdown site to be settled with ASP in actuals in cash.

197 EMERGENCY AND BREAKDOWN ASSISTANCE Disclaimer ^ On spot repairs at breakdown site Exclusion of Liabilities shall depend on nature of com-  The Service is not available in Lak- plaints & will be as per the discretion  It is understood that TATA MOTORS shadweep. of the ASP. shall be under no liability whatsoever in respect of any loss or damage aris- **The reach time is indicative & the *The decision for free of charge re- ing directly or indirectly out of any de- actual reach time will be conveyed by pairs will be as per the warranty pol- lay in or non-delivery of, defect/defi- the call centre at the time of break- icy & procedures of TATA MOTORS ciency in service/parts provided by down call. LTD. and as per the interpretation of ASP.  The reach time can vary depending the same by ASP. You will be duly in-  In case vehicle cannot be repaired on the traffic density & time of the formed by the ASP & call centre for on-site, customers are advised to day. the change applicable if any. use the towing facility for taking their  The reach time indicated does not  All charges wherever applicable vehicle to the nearest TATA MOTORS account for delays due to but not lim- need to be settled directly with the authorized workshop only. In no con- ited to acts of God, laws, rules & reg- ASP. dition will the vehicle be towed to any unauthorized workshop. TATA MO- ulations for time being in force, or- ders of statutory or Govt. authorities, TORS will not be responsible for any industrial disputes, inclement repairs carried out in such unauthor- weather, heavy down pour, floods, ized workshop. storms, natural calamities, road  Customer are advised to take ac- blocks due to accidents, general knowledgment from the ASP for the strife and law & order conditions viz. list of accessories/extra fittings and fire, arson, riots, strikes, terrorist at- other belongings in the vehicle as tacks, war etc. well as the current condition related to dents/scratches breakages of parts/fitments of the vehicle at the 198 EMERGENCY AND BREAKDOWN ASSISTANCE time of ASP taking possession of the  On site repairs may be temporary in vehicle & to verify these items when nature. The completion of repairs delivery is taken back by them, Claim does not certify the road worthiness for loss of or damage to items, if any of the vehicle. The customer is ad- should be taken up with ASP directly. vised to ensure temporary repairs TATA MOTORS shall not be responsi- carried out onsite is followed by per- ble for any such claims, dam- manent repairs at a TATA MOTORS ages/loss or any deficiency of ser- Authorized Workshop at the earliest. vice of the ASP. Terms and conditions and service coverage, exclusions etc. are subject Vehicles will be handled, repaired &  to change without notice. towed as per the customer’s risk & TATA MOTORS shall not be liable for any damages / claims as a result of

the same.  Services entitled to the customers can be refused or cancelled on account of abusive behavior, fraudu- lent representation, malicious intent and refusal to pay the charges for any charges related services and spare parts during service or on previous occasion on part of the customer.

199

EMERGENCY AND BREAKDOWN ASSISTANCE

200 MAINTENANCE

Maintenance and Service The following checks can be carried out WARNING between the recommended scheduled Periodic maintenance is essential for en- maintenance services. Take help of our  Be careful not to touch a hot en- suring long trouble free performance. gine, exhaust manifold and authorized service centre for assistance. pipes, muffler, radiator and wa- Have your vehicle serviced regularly  Engine oil level ter hoses. from TATA MOTORS Authorized Service  Do not work on a vehicle with the Centre.  Engine coolant level engine running in an enclosed There is a large network of TATA MO- space, unless you are sure of  Brake/Clutch fluid level TORS Authorized Service Centre to help enough ventilation. you with their professional servicing ex-  Washer fluid level checking & top-  Keep all open flames and other burning material (such as ciga- pertise. Scheduled maintenance infor- ping up mation is provided which makes tracking rettes) away from the battery and routine service easy.  Power steering fluid level all fuel related parts. If you need to do any work inside the  Battery electrolyte level engine compartment,  Tyre inflation pressure including  Switch off the ignition spare wheel  Never reach into the area where there is a risk of danger from moving components, such as the NOTE fan rotation area. Refer “Opening and Closing” sec-  Keep clothing away from moving tion for engine bonnet opening. parts.

201 MAINTENANCE Engine Compartment

1. Brake fluid reservoir 2. Windshield washer container 3. Coolant auxiliary tank 4. Power Steering Oil Reservoir 5. Dip stick engine oil 6. Engine oil filling cap 7. Fuse and relay box (Below Air intake) 8. Battery

202 MAINTENANCE Oil / Fluid Level Engine Oil Quality Monitoring Indi- cator Engine Oil Level Checking Your vehicle is equipped Warm up the engine to normal operating with a feature in the en- temperature. gine management system Turn it ‘OFF’ and wait for 5 minutes for which will monitor the engine oil quality the oil to return to the oil pan. Be sure through out the lifetime of the oil in the the vehicle is on a level surface. engine. This will ensure that an oil change is requested only when really Take out the dipstick, wipe it clean, and necessary. Once the oil quality reaches a reinsert it fully. Pull it out again and ex- threshold, the engine management sys- amine the oil level. It should be between Engine oil dipstick tem will ask for oil change by lighting the ‘MIN’ and ‘MAX’ level. If not, top up with above lamp. This lamp will be blinking recommended engine oil. NOTE for oil change request.  Do not remove the filler cap NOTE Depending on your driving conditions, when the engine is running. the oil quality may get deteriorated The oil consumption depends  Do not add oil above the MAX. upon the driving style and the con- sooner. For example, if you are driving mark. Oil level above the MAX. predominently in highway conditions ditions under which the vehicle is mark may cause engine dam- used. without straining the engine excessively, age. the oil lamp indicating oil change may For location of Engine oil filling cap appear later than expected. Similarly, if and dip stick, please refer Engine you drive continuously and for a long Compartment. time in city at low speeds with frequent cold starts and short journeys, the engine management system may prompt 203 MAINTENANCE you to change the oil sooner than had run again after an oil change without re- Brake/Clutch Fluid Level the car been used mainly in highways. setting oil quality using TML diagnostic tool. NOTE If the vehicle is continuously driven ig-  Under no circumstances oil noring this lamp, MIL, in addition to the change intervals should exceed above lamp, will be turned ON. Depend- 15,000 km or 12 Months, which- ing on the distance driven without oil ever occurs earlier. change and oil quality reset, the engine will go into a soft or strong performance This behaviour is absolutely normal, the reduction mode. oil change is intended to keep your engine at peak efficiency, and replacing used oil with fresh oil is normal mainte- NOTE nance and not a malfunction. Pull the notch and release the top cover  The appearance of this blinking As soon as this lamp is blinking, the oil warning light or symbol is not re- should be changed as per oil change / lated to the amount of oil in the servicing procedure. Please contact engine, so if the light or symbol nearest TATA authorized service center comes ON and blinking, never immediately. add / top up engine oil but contact the nearest TATA authorized Once the oil is changed as service center to have oil change per the normal oil change / and reset. servicing procedure, the oil quality should be reset using TML diagnostic tool. The vehicle should never be Remove the cap and check the level. Top up if required. 204 MAINTENANCE NOTE Check whether the coolant level is be- Make sure that only TATA MOTORS rec- tween the ‘MIN’ and ‘MAX’ marks pro- ommended coolant is used. Mixing of  Do not allow brake fluid to make vided on the coolant reservoir. different coolants may harm your en- contact with the skin or eyes. gine’s cooling system and its compo- When the coolant level is low, top up with  Do not allow brake fluid to splash nents. Do not add extra inhibitors or ad- or spill on the painted surface as recommended coolant up to ‘MAX’. level. ditives to the coolant. These can be it will damage the paint. In case harmful and compromise the corrosion of spillage, wipe it off immedi- NOTE protection of the engine coolant. ately. In case of emergency, a large For location of Brake/Clutch Fluid amount of water without engine WARNING Container and filling cap, please refer coolant may be added in order to reach a vehicle service location.  The engine cooling system is Engine Compartment. pressurized, particularly when Engine Coolant Level Whenever coolant has been added, the the engine is warm. When open- coolant level in the coolant reservoir ing the cap, you could get burnt should be checked few times after driv- by hot coolant spraying out. ing the vehicle to confirm correct level. There is a risk of injury.  Let the engine cool down before For location of Engine coolant con- opening the cap. Wear eye and tainer and filler cap, please refer En- hand protection when opening gine Compartment. the cap. Open the cap slowly half a turn to allow pressure to es- NOTE cape. Topping of the coolant should be

done in the auxiliary tank only.

205 MAINTENANCE

Power Steering Fluid Level WARNING Windshield Washer Fluid Level  Do not start the engine without oil Check that there is washer fluid in the in the power steering system. tank. Refill it if necessary. Use a good  Do not allow dirt into power steer- quality windshield washer fluid, diluted ing fluid reservoir during refilling with water as necessary. or top up.

NOTE Turning the steering wheel to full left or right lock and holding it there can damage the power steering pump.

The level of the power steering fluid should be between the MIN. and MAX. NOTE mark on the side of the power steering For Oil/fluid specification and fluid container. If the level falls below the Quantity, please refer ‘Mainte- MIN. mark, add recommended fluid. nance’ section. NOTE In case of leakage or hard steering, For location of Power steering fluid please contact the nearest Authorised  Do not use detergent or any other container, please refer Engine Com- additive in the windshield washer Service outlet. partment section. reservoir. This can severely im- pair visibility when sprayed on the windshield, and can also damage your vehicle’s paint.

206 MAINTENANCE  Do not operate washer motor with Battery  When this stops, wash it off with no fluid in washer tank, washer plain water. Dry off the battery with a motor will be damaged. cloth or paper towel.  Apply petroleum jelly to the terminals For location of Windshield Washer Container and filling cap, please refer to prevent further corrosion. respective Engine Compartment.  Use a proper wrench to loosen and remove cables from the terminals.  Always disconnect the negative (-ve) cable first and reconnect it last.  If your vehicle is equipped with Bat- tery Sensor, then disconnect only the Sensor Output Cable. Do not remove  To access battery terminals, remove the Sensor, Sensor connector com- the cover by removing the 5 knobs. pletely as this will result into Sensor function loss temporarily. Sensor  Examine the battery for electrolyte functionality will be restored when level against the marking on the bat- the Vehicle is parked for 3-4 hours tery outer case. without any operation.  Examine the battery terminals for Clean the battery terminals with a corrosion (a white or yellowish pow-  terminal cleaning tool or wire brush. der). To remove it, wash the terminals with a solution of baking soda. It  Reconnect and tighten the cables, will bubble up and turn brown. coat the terminals with petroleum jelly.

207 MAINTENANCE

 Make sure that the battery is se- NOTE curely mounted. Use only authorized Battery recom-  If you need to connect the battery to mended by TATA Motors. Use of any a charger, disconnect both cables to other unauthorized Battery will re- prevent damage to the vehicle’s sult into Intelligent Alternator Con- electrical system. trol (IAC) function detoriation.  If your vehicle is equipped with Bat- tery Sensor, connect the jump start NOTE leads on output terminal of Battery Authorized Battery: Sensor. Do not connect the jump 78 Ah- Enhanced flooded battery to start leads on Sensor surface or Bat- be replaced with enhanced flooded tery terminal. This will result of func- Battery battery (78 Ah) of the respective tion loss of Battery sensor. For location of battery, please refer supplier only  Refer the below Battery Sensor im- image of the respective Engine Com- partment. age for do's and don'ts. NOTE  During normal operation, the battery generates gas which is explosive in nature. A spark or open flame can cause the battery to explode causing very serious injuries.

208 MAINTENANCE  Keep all sparks, open flames Transmission Air Oil Cooler Check oil feed pipes, return pipes, air intake and exhaust piping for leakages and smoking materials away For automatic transmission, hot oil com- from the battery. and restrictions. Check the engine ing out of transmission flows through breathing system and oil separator. · Fill The battery contains sulphuric  transmission air oil cooler and gets the oil inlet hole of the turbocharger with acid (electrolyte) which is poi- cooled before entering transmission clean engine oil, when the engine is sonous and highly corrosive in again. As such it does not require any started after long storage. nature. Getting electrolyte in maintenance however it can be cleaned your eyes or on the skin can externally by blowing compressed air. cause severe burns. Wear protective clothing and a face shield WARNING or have a skilled technician to do While cleaning, ensure that inter the battery maintenance. cooler and transmission air oil cooler fins are not damaged. If the fins get damaged, it could lead to lose of performance and subsequent failure.

Maintenance Recommendations Check the boost pressure pipe for its proper fitment, damage etc. · Specified engine oil and the oil filter should be used and should be changed regularly in accordance with Service Schedule. ·

209 MAINTENANCE Tyres Inflation Recommended tyre pressure in Cold condition (Laden / Unladen) Check for inflation and condition of your vehicle tyres periodically. Tyre size Front Rear

Check the pressure in the tyres when 235/70 33 psi / 33 psi / they are cold. R16 2.27 bar 2.27 bar Keeping the tyres properly inflated gives 235/65 33 psi / 33 psi / you the best combination of riding com- R17 2.27 bar 2.27bar

fort, handling, tyre life and better fuel efficiency. NOTE Over inflation of tyres makes the vehicle In case of Air filling in hot tyre con- ride bumpy and harsh. Tyres are more dition, increase tyre pressure by 3 prone to uneven wear and damage from psi over specified cold pressures. road hazards.

Under inflated tyres reduce your comfort Under Excessive side 1 inflation tread wear in vehicle handling and are prone to fail- ures due to high temperature. They also Correct tyre cause uneven wear and more fuel con- 2 Uniform wear pressure sumption.

Excessive NOTE 3 Over inflation center tread Every time you check inflation wear pressure, you should also examine tyres for uneven wear, damage and trapping of foreign objects in the treads and wear. 210 MAINTENANCE Tyre Pressure Sticker Location For steel wheel rims with spare Wheel Alignment steel wheel rim Incorrect wheel alignment causes excessive and uneven tyre wear. Check wheel alignment at specified intervals. Wheel Balancing Wheels of your vehicle are balanced for better ride comfort and longer tyre life. Balancing needs to be done whenever tyre is removed from rim.

WARNING

On B Pillar near driver seat. For alloy wheel rims with spare If the vehicle vibrates abnormally wheel of steel wheel rim (if available) on a smooth road, have the wheel Tyre Rotation balanced done immediately. To increase tyre life rotate the tyre at specified intervals or earlier depending NOTE on the operation of vehicle.  While driving in snow, It is advisa- The illustrations shows how to rotate ble to use the snow chain on tyres when normal or temporary spare roads. Follow assembly and wheel is fitted. safety instruction provided by the snow chain manufacturers.  Please refer service schedule for wheel alignment.

211 MAINTENANCE Special Care for Tubeless Tyres  Maintain recommended inflation Remote Key Battery Replacement pressure. Over-inflation, in particu- (For Flip key)  While removing tyre from wheel rim lar, may cause puncture or bursting and mounting it back on wheel rim, Remote control key contains a battery, of tyre. take precautions not to damage tyre which is housed under the cover. bead. Use tyre removal and assem- NOTE If red LED on remote flashes for 5 times bly machines. Damage or cut on tyre  Life and wear pattern of tyres de- after operating any button on remote. It bead may cause gradual loss of air pends on various parameters like is recommended to replace battery at a and deflation of tyre. tyre pressure, wheel alignment, TATA MOTORS Authorised Service Cen- tre.  Do not scratch inside of tubeless tyre wheel balancing, tyre rotation, with metallic or sharp object. Tube- etc. It also largely depends on ve- You should, however, proceed as follows less tyres are coated with impermea- hicle speed, load carried, usage, if you wish to replace the discharged bat- driving habits, road conditions, ble layer of rubber from inside which tery yourself: tyre quality, etc. In case fault is holds the air inside the tyre. Removal suspected to be due to poor qual- 1. Open the key blade. of this layer due to scratching may ity of tyres, the same may be cause gradual loss of air and defla- taken up with concerned tyre 2. Press off the battery cover with your tion. manufacturer. thumb or using a flat screwdriver at the points of the arrows.  If wheel rim gets damaged in service,  For steel rim, Red dot of tyre to be get the wheel rim repaired/ replaced matched with blue dot of rim 3. Remove the discharged battery from while re-fitment. immediately. Running the vehicle the key by pressing the battery down- with damaged rim may cause defla-  For alloy rim, Yellow dot of tyre to wards at the point of the arrow. tion of tyre and subsequent dislodg- be matched with valve of rim ing of tyre from rim. while re-fitment.

212 MAINTENANCE 5. Ensure that the “+” symbol on the Smart Key Battery Replacement battery is facing upwards. The cor- (For PEPS variant) rect polarity is shown on the battery Procedure: cover. 1. Open rear side of key (battery cover). 6. Position the battery cover on the key and press on it until it is heard to lock in place.

NOTE Use CR 2032 battery only.

4. Insert the new battery. NOTE An inappropriately disposed battery can be harmful to the environment and human health. Dispose the battery ac- 2. Replace with new battery in the cording to your local law(s) and smart key battery slot with proper po- regulation. larity of battery. 3. Close the battery cover. 4. Ensure that the key cover is intact properly.

213 MAINTENANCE On Board Diagnostic (OBD II) instrument cluster, when a fault causes System emission levels to increase. Diagnostic connector is located on RH The OBD system also has a diagnostic side below the steering wheel. connector that can be interfaced with appropriate diagnostic tools, which makes it possible to read the fault codes stored in the Electronic Control Unit, together with a series of specific parameters for Engine operation and Diagnosis. This check can also be carried out by the traffic police.

On board Diagnostics or OBD, is an auto- motive term referring to a vehicle’s self- diagnostic and reporting capability. The OBD system allows continuous diagnosis of the components of the vehicle cor- related with emissions. This system warns the driver, by turning “ON” the Malfunction Indication lamp (MIL) on the

214 MAINTENANCE Diesel Particulate Fil- In certain specific driving conditions, process normally takes about 20 ter (DPF) Warning Indi- DPF regeneration may not happen auto- minutes. cator matically as the desired temperatures required to regenerate soot may not be NOTE Your vehicle is equipped with a Diesel achievable due to specific driving condi- Do not shut down engine till the Particulate Filter (DPF). DPF is a me- tions. This includes prolonged driving at warning lamp goes OFF. chanical filter that physically traps par- low vehicle speeds for considerable ticulate matter from diesel engine ex- amount of time (driving in heavy city traf- If DPF regeneration process requested haust gas. fic), prolonged running of the engine in above is not followed for a long distance DPF traps the particulate matter in the idle conditions etc. In such cases, a and the vehicle is driven following way: warning lamp as indicated above will be with warning lamp ON, it can illuminated in the instrument cluster in- cause MIL to be turned ON.  Filtration – Particulates / soot are dicating that soot regeneration is insuffi- Once MIL is ON, please con- collected in the inlet channel of the cient. tact nearest TATA authorized service filter. This warning lamp switches ON con- center.  Regeneration – When the filter stantly to indicate that the DPF needs to Service should connect the TML diag- channels are filled up with soot, they be regenerated. This lamp does not indi- nostic tool and conduct DPF service re- are cleaned automatically by the en- cate any malfunction. generation as indicated in the diagnostic gine management system. This pro- tool. cess is known as DPF Regeneration The warning lamp remains OFF during Insufficient DPF regeneration resulting and this will happen during normal normal vehicle behavior and lights up in the above lamps can also happen if running of the vehicle. only when driving condition requires the the vehicle is driven with adultered die- driver to be notified. When this lamp is DPF equipped in vehicle normally regen- sel. ON, keep the car running ideally at 3rd erates automatically which is controlled gear, 60km/hr with engine speed over by engine management system. 2000 rpm until regeneration is completed and warning lamp goes OFF. The 215 MAINTENANCE Service Instructions The TATA HARRIER has been manufactured to give you eco- nomical and trouble free performance. To achieve this, please Servicing of the vehicle can be done at any TATA MOTORS follow the instructions as stated. Authorised Dealer Workshop or TATA MOTORS Authorised Service Centre (TASC). Your vehicle is entitled to three free services (labour only). The free service coupons are attached to the sales invoice. Please Warranty claims can be settled by any TATA MOTORS Author- present these coupons to the servicing dealer while availing ised Dealer Workshop or TATA MOTORS Authorised Service free services. Centre (TASC).

1st free service - At 1,000 - 2,000 kms. OR 2 months, whichever is earlier.

2nd free service - At 7,000 - 8,000 kms. OR 6 months, whichever is earlier. 3rd free service - At 14,500 - 15,500 kms. OR 12 months, whichever is earlier. All services other than free services are chargeable.

216 MAINTENANCE Service Schedule

PDI

15K 30K 45K 60K 75K 90K

1.5K 7.5K

Kms

105K 120K 135K 150K

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

SN Operation 112.5K 127.5K 142.5K Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

General

Wash the vehicle Every 1 & Clean Conden- ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Service ser Fins.

Check & Top up Fluids (If required): Transaxle Oil, Die- sel Exhaust Fluid Every 2 (DEF)*, Coolant, ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Service Brake Fluid, Bat- tery Electrolyte, Wind Screen washer fluid.

Check Fuel Lines Every 3 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● for Leakages. Service

Check and Cap- ture all DTC's Every 4 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Clear all faults and Service Erase the Codes.

Check & Replace if 30K/ 5 found damaged -- ● ● ● ● ● 24M Exhaust hanger

Check all door latch & striker op- 15K/ 6 erations, Adjust If ● ● ● ● ● ● ● ● ● ● 12M required and apply grease if required.

# - Kms or Months whichever occurs earlier 217 MAINTENANCE

PDI

15K 30K 45K 60K 75K 90K

1.5K 7.5K

Kms

105K 120K 135K 150K SN 22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

Operation 112.5K 127.5K 142.5K

Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

Check Rubber Boots, Rubber seat, Dust cover & Bushes for damage & replace if 7.5K / 7 required (Suspen- ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 6M sion). Driveshaft - Rubber boot, any cracks, Oil seep- age observed – Replace or rectify. Check for all bolts 7.5K / 8 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● & nuts (Tighten). 6M Engine (Diesel)

Change engine oil 15K / 1 ● ● ● ● ● ● ● ● ● ● and Oil filter. 12M

Drain water from 7.5K / 2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Fuel Filter Bowl. 6M

Replace fuel filter 15K/ 3 ● ● ● ● ● ● ● ● ● ● cartridge. 12M

Check AC & alternator belt condi- 15K / 4 tion visually, re- ● ● ● ● ● ● ● ● ● ● 12M place if found damage.

# 60K / 5 Change coolant. ● ● 36M

# - Kms or Months whichever occurs earlier 218 MAINTENANCE

PDI

15K 30K 45K 60K 75K 90K

1.5K 7.5K

Kms

105K 120K 135K 150K

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K SN Operation 112.5K 127.5K 142.5K Month 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120 s Replace air filter element # (more frequently for vehi- 6 30K / ● ● ● ● ● cle operating in severe 36M condition). Replace timing drive kit # 7 (Timing belt, Auto ten- 150K ● sioner and Idler). /60M Replace FEAD kit (Belt, 90K/ 8 idler 1&2, Auto ten- ● 48M sioner) Transaxle Check oil level and top 15K / 1 up if necessary – Manual ● ● ● ● ● ● ● ● ● ● 12M Transmission. Automatic Transmission 2 Filled for life time fluid Steering Check oil level and top 15K / 1 ● ● ● ● ● ● ● ● ● ● up if necessary. 12M # Replace Power steering 2 105K ● Oil & filter element. / 36M Brakes

Check front brake pads 15K / 1 & rear brake linings. Re- ● ● ● ● ● ● ● ● ● ● 12M place if necessary.

Replace brake fluid. # Check brake system 2 45K / ● ● ● components for Leak- 24M ages. # - Kms or Months whichever occurs earlier 219 MAINTENANCE

PDI

15K 30K 45K 60K 75K 90K

1.5K 7.5K

Kms

105K 120K 135K 150K

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

SN Operation 112.5K 127.5K 142.5K Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

Inspect & if neces- 15K / 3 sary adjust hand- ● ● ● ● ● ● ● ● ● ● brake setting. 12M

Wheels & Tyres

Check & Adjust # 15K / 1 ● ● ● ● ● ● ● ● ● ● Wheel alignment. 12M

Check for Tyre # 7.5K / 2 pressure, condi- ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 12M tion & rotate.

Electrical

Check specific 7.5K/ 1 gravity of battery ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● electrolyte. 6M Check headlamp 15K / 2 ● ● ● ● ● ● ● ● ● ● focussing. 12M

A.C. System

Clean filter and check Air-conditioning / HVAC Every 1 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● system for satis- Service factory performance. Replace Pollen Fil- 15K/ 2 ● ● ● ● ● ● ● ● ● ● ter. 12M # - Kms or Months whichever occurs earlier

220 MAINTENANCE

PDI

15K 30K 45K 60K 75K 90K

1.5K 7.5K

Kms

105K 120K 135K 150K

22.5K 37.5K 52.5K 67.5K 82.5K 97.5K

SN Operation 112.5K 127.5K 142.5K Months 0 2 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120

Sunroof

Check and clean Every 1 the guide rails and ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Service drain holes.

Clean the guide rails and mecha- 7.5K / 2 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● nism and apply 6M grease.

# - Kms or Months whichever occurs earlier

* DEF is a consumable item, refill or replacement is not based on service intervals. The consumption of DEF can vary depending on driving style, and road and weather conditions **-- For severe off-road usage, above checks to be done at every 5,000 km or after every severe usage event.

221 MAINTENANCE Additional Maintenance Schedule under Severe Driving Conditions

Sr. Condition Operation Frequency No. A B C D Change every 7500 km or 6 months or whenever oil quantity lamp Engine oil and oil filter ● ● ● ● 1 glows.

2 Air filter element Change at every 15,000 km or 18 months whichever is earlier. ● ●

A - Driving in conditions such as Patrolling, Pickup Van, Vehicle Towing, with Trailer Towing B - Driving on Dusty / Sandy roads C - More than 50% (in terms of km) driving in heavy city traffic D - Frequently operating in mountainous area

NOTE In case of emergency, a large amount of water without engine coolant may be added in order to reach a vehicle service location.

222 MAINTENANCE Vehicle Parking for Long Duration 7. Wiper blade lifting sequence during Exhaust After Treatment System (Non - Use Maintenance) cleaning / replacing, first lift front passenger side wiper blade, then Exhaust after treatment consists of be- If you want to park your vehicle at one driver side blade. low components: place for long duration, following care is 1. Diesel Oxidation Catalyst (DOC) to be taken: 8. Slightly open the windows. 2. Diesel Particulate Filter (DPF) 1. Park the vehicle in covered, dry and 9. Cover the vehicle with a cloth or per- if possible well-ventilated premises. forated plastic sheet. Do not use 3. Selective Catalyst Reduction (SCR) Engage a gear. sheets of imperforated plastic as they do not allow moisture on the ve- 4. Various Sensors and Actuators. 2. Remove the battery terminal cables hicle body to evaporate. (first remove the cable from the neg- The exhaust gas coming from the engine ative terminal). Ensure that battery is 10. Inflate the tyres to 0.5 bar above the first passes through the DOC and then fully charged. normal specified pressure and check through DPF. it at regular intervals. 3. Block the wheel or engage in the DPF is a filter, which filters carbon soot gear mode. 11. Check the battery charge every six in the exhaust gas. DOC and DPF con- weeks. tains precious metals which converts hy- 4. Clean and protect the painted parts drocarbons, carbon monoxide etc. in the 12. Do not drain the engine cooling sys- using protective wax. exhaust gas to harmless constituents. tem. 5. Clean and protect the shiny metal Additionally DPF also removes most of parts using commercially available the carbon soot particles in the exhaust special compounds. gas. The collected carbon soot in the 6. Sprinkle talcum powder on the rub- DPF is regenerated to clean the filter. ber windscreen wiper and lift them off the glass.

223 MAINTENANCE In order to reduce the NOx levels even In certain specific driving conditions, require the driver to be notified. To further, SCR system is used. In SCR sys- DPF regeneration may not happen auto- switch off the lamp, keep the car running tem, urea is injected in the exhaust matically as the desired temperatures until regeneration is complete (ideally at stream. With the help of injected ammo- required to regenerate soot many not be 3rd gear, 60 kmph. with engine speed nia in the urea, NOx is converted into achievable due to specific driving condi- over 2000 rpm). The process normally harmless constituents. tions. This may happen in prolonged takes about 20 minutes. driving at low vehicle speeds for consid- Regeneration Process Note: Failure to obey the correct proce- erable amount of time (driving in heavy dure for long distance when the DPF DPF is a mechanical filter that physically city traffic), prolonged running of the en- lamp comes ON can cause the warning traps particulate matter from diesel engine in idle conditions, use of adulter- lamp (MIL) to come ON. In that case, gine exhaust gas. ated diesel etc. please contact nearest TATA authorized service center to restore correct DPF op- In such cases, a DPF warning lamp will DPF traps the particulate matter in the eration. following way: be illuminated indicating that soot regeneration is insufficient WARNING  Filtration – Particulates / soot are collected in the inlet channel of the DPF Lamp Avoid parking of vehicle over inflam- mable materials, such as dry leaves; filter. The lamp blinks constantly grass etc. as exhaust system is hot to indicate that the DPF  Regeneration – When the filter chan- enough to initiate fire. nels are filled up with soot, they are needs to eliminate the trapped pollutants (particu- cleaned automatically by the engine WARNING management system. This process is late matter) through the regeneration known as DPF Regeneration and this process, it therefore does not indicate a  Ensure exhaust system is not will happen during normal running of malfunction. The lamp remains off dur- blocked and is free from obstruc- ing the entire DPF regeneration and it the vehicle. tion. lamps up only when driving conditions

224 MAINTENANCE  Blockages in the exhaust can cre- LOWER than 32°C, it has a shelf life of Copper, brass, aluminum, iron or ate backpressure, low top speed, at least one year. non-stainless steel should be poor pick up, black smoke, car- avoided as they are subject to cor- bon build up and low mileage and NOTE rosion by DEF (UREA). can affect power output of the en- DEF (UREA) freezes at temperatures  If DEF (UREA) is spilled, it should gine and the emission levels. lower than -11°C. be wiped up completely.

WARNING DEF Storage Adding DEF (UREA) The maximum sulphur content of DEF (UREA) is considered a very stable Preliminary Conditions the diesel fuel must not exceed product with a long shelf life. If DEF Consumption of the additive DEF (UREA) 0.001% (10 parts per million). Fail- (UREA) is kept in temperatures between depends on the condition of vehicle use ure to comply with the standards - ° and °C, it will last a minimum of 12 32 and is indicated on the instrument clus- may damage engine components one year. ter. and the exhaust after-treatment DEF (UREA) is subject to freezing at the system. lowest temperatures. For example, DEF DEF (UREA) freezes at temperatures (UREA) may freeze at temperatures at or lower than -11°C. If the car stands for a Diesel Exhaust Fluid (DEF) below 11°C. The system has been de- long time at this temperature refilling (if available) signed to operate in this environment. could be difficult. For this reason, it is ad- The vehicle is equipped with DEF (UREA) vised to park the vehicle in a garage NOTE injection system and Selective Catalytic and/or heated environment and wait for Reduction (SCR) to meet emission When working with DEF (UREA), it is the urea to return to liquid state before standards. important to know that: topping up.  Any containers or parts that DEF (UREA) is a very stable product with comes into contact with DEF a long shelf life. Stored at temperatures (UREA) must be DEF (UREA) com- patible (plastic or stainless steel). 225 MAINTENANCE Proceed as follows: Urea Quantity Refilling  Park the car on flat ground and stop 1. Empty tank (for example, first fill- the engine by placing the ignition in ing or urea tank replacement) - It the OFF position. is recommended that urea tank is filled to full capacity. At least, a min-  DEF (UREA) filler is located in the tail- imum of 8L of urea should be filled. gate compartment below the tool kit tray. Open the tailgate and remove 2. Partially full tank (vehicle run the tool kit tray and remove the cap without filling urea) - It is recom- from the DEF (UREA) filler. mended that urea tank is filled to full capacity. At least, a minimum of WARNING 6L of urea should be filled. Never fill DEF (Urea) or diesel fuel Urea Filler Tank NOTE into the wrong filling ports. This Urea Refilling Procedure Do not switch on the key during refill may result serious damage to En- Conditions for refilling: gine, Fuel system and Emission operation if refill is not done in one at- system components. In case of Vehicle speed = 0km/h tempt wrongly filled do not start the en- Vehicle should be on a flat road surface After completing urea filling in ignition gine, contact TATA Motors Author- key OFF condition, perform key ON and ised Service Centre. Vehicle should be turned OFF wait for about 3 minutes before cranking

the engine. In case of engine stops after refill operation, wait for about 2 minutes in order to store correct urea level in EMS ECU before switching ON the key again. Ensure that urea is cold while filling. 226 MAINTENANCE Precautions While Refilling Urea  Fill urea in the tank till tank is full. Low DEF Level Warning Messages This will require around 15 liters of Refilling With Nozzles These messages will be indicated when urea. DEF level is low. This can happen when You can fill up at any DEF (UREA) distrib-  Ensure Ignition is OFF during the en- vehicle runs without filling DEF in spite of utor. tire urea filling process. Once urea message to fill DEF. Proceed as follows: filling process is complete, keep igni-  First warning message will be indi- tion key in ON position for around  Insert the DEF (UREA) nozzle in the 2 - cated at approximately in between filler, start refilling and stop refilling 3 minutes. 1500 - 2400km before emptying of at the first shut-off (the shut-off indi-  Ensure urea level indication in instru- DEF tank at the current DEF con- cates that the DEF (UREA) tank is ment cluster is updated and urea re- sumption rate. “DEF LEVEL LOW, RE- full). Do not proceed with the refill- lated messages disappears. FILL SOON” message will be indi- ing, to prevent spillage of DEF cated at this warning level. (UREA). Urea should be filled with vehicle parked in a flat area. Please ensure that ignition  Extract the nozzle. is in OFF condition. In case the urea is Refilling With Containers filled with vehicle parked in an inclined condition, urea level updation may not Proceed as follows: happen.  Check the expiration date and ensure the validity of DEF.  Read the advice for use on the label before pouring the content of the bottle into the DEF (UREA) tank.

227 MAINTENANCE  If the vehicle runs without filling DEF,  On further driving the vehicle without Once the engine is stopped with this next warning level will be indicated at filling DEF, message “ENGINE WILL message, it will not be possible to restart approximately 600km before empty- NOT RESTART IN NEXT KEY ON” will the engine without filling DEF. ing of DEF tank at current DEF con- appear. sumption rate. “ENGINE STOPS IN NOTE 600KM” message will be indicated Please refer to DEF filling procedure at this warning level. This message for filling DEF. will continue till DEF tank becomes empty with corresponding distance gradually reducing to 0km.

 Message “ENGINE STOP TANK EMPTY” will be displayed once DEF tank is empty.

228 MAINTENANCE

DEF Level Messages in case of SCR corresponding distance gradually reduc- NOTE System Fault ing to 0km.  Please refer to DEF filling proce- These messages will be indicated when After this, engine will not start in the next dure for filling DEF. there is any problem in the SCR system ignition cycle. The vehicle has to be  Messages may vary slightly de- and SCR system fault is displayed. brought to TML service centre for rectifi- pending on the vehicle variant. cation.  Depending on the distance, the vehicle can run before emptying of DEF DEF Level Messages in case of

tank at the current DEF consumption Poor Quality DEF rate. “SCR SYSTEM FAULT, ENGINE  In case of use of poor quality of DEF, STOPS IN XXX KM” message will be message “DEF QUALITY LOW, EN- indicated. GINE STOPS IN XXX KM” will appear. In such cases, currently filled DEF has to be drained completely and proper good quality DEF needs to be filled until DEF tank is full.

If the vehicle is run without rectifying the SCR system (through TML service centre), warning message will continue with

229 MAINTENANCE

230 TECHNICAL INFORMATION

Fuel Specification

Fuel (Diesel)

Normal grade BS VI compliant diesel conforming to

IS1460:2017 or equivalent is recommended to be used as fuel. Do not use premium diesel available in the market for example extra premium / Turbojet etc.

Recommended Fuel Specifications

Parameter Unit BS VI Cetane Number (min) C N 51

Sulphur content mg/kg 10

Lubricity (HFRR) micron 460

NOTE It is mandatory to use Diesel fuel with recommended Sulphur contents as given above. Use of any other diesel

fuel can increase the pollutants/damage the engine or exhaust after treatment system.

231 TECHNICAL INFORMATION Lubricant Specification Use following genuine fluids, coolants and lubricants recommended for optimum performance of your vehicle.

Item Specification Company Brand Qty.

Engine oil (Diesel) 0W20 ACEA C2 PETRONAS Tata Motors Genuine Oil Fully Synth 0W20 5 L

Coolant (Pre- SUNSTAR CCI Tata Motors Genuine Coolant 2200 mixed) (Antifreeze Class II/JIS K2234 Tata Motors Genuine Coolant Purocool++ Anchemo 7 L agent +Soft water TATA SS7700S1 ANSYESCO 40:60 ratio) Anand Manual Transaxle PETRONAS ZC 601 PETRONAS TATA Motors Genuine Transaxle oil HARRIER 1.9 L Oil FF Automatic Trans- ATF SP-IV M1 SK LUBRICANTS ATF SP-IV M1 7.82L mission Oil GOLDEN CRUISER TATA Genuine Brake Fluid Brake / Clutch fluid SAE J 1703, DOT 4 CASTROL Universal Brake fluid DOT 4 0.71L PETRONAS TUTELA Brake Fluid DOT 4 Power Steering oil ATF-DEXRON III CASTROL ATF DEX III 1L Diesel Exhaust Solution confirms to NPL TATA ORIGINAL D.E.F 15 L Fluid (DEF) ISO22241 standards.

Refrigerant R134a - - 500±20 gms

Compressor Oil SP 10 SANDEN VIKAS SP10 COMPRESSOR OIL-SANDEN VIKAS-L 0.25 135cc

232 TECHNICAL INFORMATION Technical Specifications Parameter Specifications Engine Model/type 2.0L KryoTec BSVI Capacity 1956 cc Max. Engine output 125 kW (170 PS) at 3750 rpm Max. Torque 350 Nm at 1750-2500 rpm Clutch Type Dry, Single Plate diaphragm type Outside diameter of clutch 240 mm Transaxle (MT) Model C635 Type Manual, 6-speed, Synchromesh No. Of gears 6 Forward, 1 Reverse Transaxle (AT) Model 6F33- HTS Type Automatic, 6-speed, Planetary No. Of gears 6 Forward, 1 Reverse Steering Type Power assisted-Hydraulic with Tilt & Telescopic mechanism and collapse feature

233 TECHNICAL INFORMATION

Parameter Specifications Brakes Brakes Front (Disc); Rear (Drum) Parking Brakes Cable Operated mechanical Suspension Front: Independent lower wishbone MacPherson strut with coil spring Type Rear: Semi-independent Twist blade suspension with Panhard rod & coil spring Front: MacPherson strut Damper twin tube with gas filled Shock absorber Rear: Damper twin tube with gas filled Wheels & tyres For Front & Rear, Option 1 : 235 / 70 R16 105H (Radial-Tubeless) Tyres Option 2: 235 / 65 R17 104H (Radial-Tubeless) For Spare wheel, (16 Inch) : 235/70 R16 106S (Radial, Tubeless) Option 1: 6.5J X 16 steel wheel Wheel rims Option 2 : 7.5J X 17 alloy wheel Fuel tank Capacity 50 liters Urea/DEF tank Capacity 15 liters

234 TECHNICAL INFORMATION

Parameter Specifications Cab / body Type Monocoque Electrical system System voltage 12 Volts Alternator capacity 150 Amp Battery 12V, 78 Ah Main chassis dimension (in mm) Wheel base 2741 Track front 1616 Track rear 1630 Overall length 4598 Overall height 1706 Max. Width 1894 over body Min. Ground clearance 153 mm (laden)

235 TECHNICAL INFORMATION

Parameter Specifications Performance Max. Speed 170 kmph Max. Recommended gradability 35%

Minimum Turning Circle Dia. in meters 11.6 m

Minimum Turning Clearance circle dia. 12.2 m in meters Weight (in kg) 1655 (XE) 1663 (XM) 1668 (XT) 1680 (XZ) Kerb weight (unladen) 1710 (XZ+) 1688 (XMA) 1705 (XZA) 1719 (XZA+)

2130 (XE) 2138 (XM) 2143 (XT) 2155 (XZ) Gross vehicle weight 2185 (XZ+) 2163 (XMA) 2180 (XZA) 2194 (XZA+)

236 TECHNICAL INFORMATION Vehicle Dimensions

NOTE: Dimensions are in mm Unladen condition

237 TECHNICAL INFORMATION Aggregate Identification Numbers

VIN plate near Front passenger seat Transaxle No. Punching (AT) Engine No. Plate – Diesel

Chassis No. punching near driver seat Transaxle No. Punching (MT) (RHS) Transmission Sticker number (AT) 238 CAR CARE AND VALUE ADDED SERVICES Car Care 4. To remove stubborn stains and con-  Always close the sunroof while taminants like tar, use turpentine or washing the vehicle. Your vehicle is subjected to many exter- cleaners like ‘Stain remover’ which nal influences such as climate, road con- are safe for paint surfaces. ditions, industrial pollution and proximity WARNING to the sea. These conditions demand 5. Avoid substances like petrol, diesel, kerosene, benzene, thinner, acids or regular care of the vehicle body. Dirt, in- Do not direct high pressure washer sects, bird droppings, oil, grease, fuel other solvents that cause damage to fluid/ water jets (Pressure above paint. and stone chippings should be removed 0.5 bar) at electrical devices and as soon as possible. 6. Dry your vehicle thoroughly to pre- connecter during washing. This is vent any damp spots. to prevent malfunction / failure of Washing 7. Rinse all surfaces thoroughly to pre- electrical system due to water ingress. Following these tips while washing your vent any traces of soap and other cleaners as this may lead to the for- vehicle. After drying the vehicle, inspect it for mation of stains on the painted sur- chips and scratches that could allow cor- 1. Always wash your vehicle in shade face later. and the surface is at room tempera- rosion to start. Apply touch up paint ture. NOTE where necessary. 2. Wash with mild vehicle wash soap  Avoid parking the car under Cleaning of Carpets like ‘Car Shampoo’ and use a soft trees without proper cover, it will bristle brush, sponge or soft cloth reduce the amount of bird drop- Vacuum clean the carpet regularly to re- and rinse it frequently while washing pings, tree sap and pollen con- move dirt. Dirt will make the carpet wear to avoid scratches. tact on paint surface. Regularly out faster. Periodically, shampoo the carpet to keep it looking new. 3. To avoid scratches, please wear soft remove the twigs, leaves and gloves. Remove finger rings, nails, vegetation near the windshield Use carpet cleaners (preferably foam wrist watch while washing. areas, to avoid water stagna- type). Follow the instructions that come tion. with the cleaner. Apply it with a sponge 239 CAR CARE AND VALUE ADDED SERVICES or soft brush. Keep the carpeting as dry FAST TAG Polishing as possible by not adding water to the Polishes and cleaners can restore shine foam. FAST TAG is pasted on front windshield from the inside. It enables Electronic toll to the painted surface that has oxidized and become dull. They normally contain NOTE collection. mild abrasives and solvents that remove Avoid wiping of painted surface in the top layer of the finish coat. Polish dry condition as it may leave your vehicle, if the finish does not regain scratches on the painted surface. its original shine after using wax.

Cleaning of Windows, Front and Interior Fabric Cleaning Tips NOTE Rear Glasses 1. Stains should be treated immedi- Clean the windows inside and outside Do not attempt to rip or tamper the ately. If left for a long time, they can with commercially available glass clean- tag. It will disable the functionality leave a permanent mark. ers. of the tag. 2. Cleaning the stains immediately is This will remove the haze that builds up Waxing important especially for stains, which on the inside of windows. Use a soft contain artificial colors in the stain Waxing and polishing is recommended cloth or paper towels to clean all glass creating liquid or semisolid sub- to maintain the gloss and wet-look ap- and plastic surfaces. stance. The colorant may leave a pearance of your paint finish. stain if kept for longer time. 1. Use good quality polish and wax for 3. Stain should not be removed by rub- your vehicle. bing. As far as possible, try to blot or Re-wax your vehicle when the water 2. lift the stain with cloth or plastic spat- does not slip off the surface but col- ula and then clean the remaining lects over the surface in patches. stain with cloth or sponge.

240 CAR CARE AND VALUE ADDED SERVICES 4. If the stain has dried, then gently Proper Cleaning Periodic Inspection brush off the material and then press with damp cloth or sponge till it dis- In order to protect your vehicle from cor-  Regularly inspect your vehicle for any appears. rosion it is recommended that you wash damage in the paint film such as your vehicle thoroughly and frequently in deep scratches and immediately get 5. Do not use household detergents to case: them repaired from an authorized clean the fabric. service outlet, as these defects tend  There is a heavy accumulation of dirt to accelerate corrosion. 6. Always use clean cotton cloth for and mud especially on the under- cleaning. body.  Inspect mud liners for damages. Paint Care  It is driven in areas having high at-  Keep all drain holes clear from clog- mospheric pollution due to smoke, ging. Following guidelines will help you to pro- soot, dust, iron dust and other chem- Proper Parking tect your vehicle from corrosion effec- ical pollutants. tively.  Always park your vehicle in shade to  It is driven in coastal areas. protect it from harsh sunlight or in a NOTE  The underbody must be thoroughly well-ventilated garage so that there Avoid spillage or direct contact of pressure washed after every three is no dampness on any part of the ve- air freshener liquid/ chemicals to months. hicle. interior painted plastic parts. In addition to regularly washing your car, Wiper Care These chemicals may cause dam- the following precautions need to be age to paint like blisters, peel off, taken.  To prevent damage to the wipers or wrinkles etc. windshield, do not operate the wipers when the windshield is dry.

 To prevent damage to the wiper arms and other components, do not attempt to move the wipers manually 241 CAR CARE AND VALUE ADDED SERVICES Value Care – AMC Value Care (AMC) is a fixed cost maintenance plan that guarantees protection against unexpected repairs & provides substantial savings through protection against inflation & price volatility of consumables during the running of the vehicle. Our customers can choose from Value Care Gold, Value Care Silver, Promise to Protect (P2P) and Protect plus plan as per the requirement & usage to ensure hassle free, reliable & economic maintenance of the vehicle. Coverage – Schedule Service and Wear & Tear. Advantage (Customer Benefits)  Price protection against rising prices of lubes and parts.  A higher resale value for your vehicle.  Peace of mind with Cashless repairs & services.  Vehicle servicing at a workshop of your choice pan India.  Covers Repairs including Wear & Tear parts viz. Brakes, Suspension, Wiper, Clutch, Brake Pads, Brake Liners etc.  Covers Scheduled maintenance services including Lubricants, Parts, Wheel Alignment and Balancing Labour.  Available at unmatched value…. Huge Savings!!!  Savings on Goods & Services Tax whenever vehicle attend under AMC.

242 CAR CARE AND VALUE ADDED SERVICES Available Offers (Types of AMC)  Silver AMC  Gold AMC  Promise to Protect (P2P)  Protect Plus Silver AMC Value Care Silver Plan covers the following:  Scheduled maintenance services at periodic interval of Km for Labor, Parts & Consumables. a. Change of Oil Filter, Fuel Filter, Air Filter & Sedimenter. b. Change of Engine Oil, Transmission Oil (if applicable), and Power steering Oil*. c. Change of Coolant, Brake Oil & Clutch Fluid*. d. General Checkup, Wheel Alignment / Balancing (Excluding Balancing Weight). e. Washing of Vehicle, Wheel greasing as applicable. Gold AMC The value care Gold Plan extends your scheduled maintenance cover to include any normal wear and tear items identified during the scheduled service and other vehicle parts that need to replace during the period of cover arising from proper and uniform usage.  Scheduled maintenance services at periodic interval of Km for Labor, Parts & Consumables.

243 CAR CARE AND VALUE ADDED SERVICES In addition to coverage mentioned under Silver AMC, the Gold AMC also covers Repairs or Replacement of Wear & Tear Items for both Parts & Labour. a. Brake Pads, Brake Liners, Wheel Cylinders. b. Clutch Disc, Clutch Cover, Cables, Mountings. c. Suspension Bush, Wiper Blades, Auxiliary Belt & other Wear & Tear Items. d. Washing of Vehicle, Wheel greasing as applicable. Promise to Protect (P2P) Value Care – Promise to protect (P2P) is a maintenance plan that guarantees protection against unexpected wear & tear repairs to provide substantial saving through protection against inflation & price volatility during the running of the vehicle. New Vehicle (under warranty vehicles) are eligible to avail this offer –Identified 13 wear & tear parts listed below Including Labour is covered in this AMC with the price range of 11 to 14 paisa per Km. *applicable to selected models* List of Covered Parts- Clutch, Brake Pad, Brake Linings, Brake Disc, Wiper, Wheel Cylinder, Suspension Bushes, Engine Mount- ings, Ball Joints, Hoses, Auxiliary Belt, (Alternator & A/C Belt), Window Winder. Protect Plus The value care Protect plus Plan extends your scheduled maintenance cover to include coverage of P2P. It covers scheduled maintenance services – labour, parts & consumables + Identified 13 wear & tear parts of P2P plan Including Labour. New Vehicle (under warranty vehicles) are eligible to avail this offer. *Applicable to selected models*

244 CAR CARE AND VALUE ADDED SERVICES

NOTE  AMC is available in the dealership from where you have purchased your vehicle.  We strongly recommend purchase of AMC at time of purchase of your vehicle to get benefit for coverage of Scheduled Services and Wear & Tear parts.  The Dealer Service Marketing Executive shall explain to you the Terms and conditions, Coverage and Owner’s responsibility.  One Time payment is to be made to avail AMC offer.  P2P & Protect plus offer valid on selected models & may vary from Model to Model, Variant to Variant.  Please read the offer eBooklet for further details about coverage and exclusions of various AMCs.

Owner’s Responsibility:  Proper use, maintenance and care of the vehicle in accordance with the instructions contained in the Owner’s Manual and Service Booklet. The records of the same to be ensured in Owner’s Manual.  Retention of maintenance service bills.

I / We have been explained the Terms and conditions, Coverage and Owner’s responsibility by the Dealer Service Marketing Executive. I wish to avail / Do not wish to avail extended warrant policy.

Customer’s Signature Dealer’s Signature

245 CAR CARE AND VALUE ADDED SERVICES Extended Warranty TATA MOTORS recommends the purchase of its extended warranty program. Coverage - Mechanical + Electrical Benefits  Insures you against unforeseen break down repair bills.  Documentation is simple and hassle free.  Near cashless & speedy claim Term 2+1 Year or 1,15,000 Km whichever occurs first OR 2+2 Year or 1,30,000 Km whichever occurs first OR 2+3 Year for Unlimited Km Extended Warranty is available in the dealership from where you have purchased your vehicle. We strongly recommend purchase of Extended Warranty at time of purchase of your vehicle. Extended Warranty can be availed until warranty period from date of purchase of vehicle. The Dealer Service Marketing Executive shall explain to you the Terms and conditions, Coverage and Owner’s responsibility.

246 CAR CARE AND VALUE ADDED SERVICES Note  The 12 or 24 or 36 months extended warranty does not follow the 24 months Manufacturer's warranty.  The extended warranty comes into force once the manufacturer’s warranty expires e.g. after 24 Months.  It is more restrictive as by the time it comes into force the vehicle is already 24 months old. What is covered?  Mechanical / Electrical break down as defined in this warranty and confirmed by the dealer within the stipulated terms and conditions.  TATA MOTORS dealer shall either rep air or replace any part found to be defective with a new p art or an equivalent at no cost to the owner for p arts or labour.  Such defective parts which have been replaced will become property of TATA MOTORS LIMITED.  Comprehensive list of parts covered is mentioned in the Extended Warranty Booklet. What is not covered? Please refer the digital Extended Warranty booklet provided by the dealer for details of the exclusion list. Owner’s Responsibility:  Proper use, maintenance and care of the vehicle in accordance with the instructions contained in the Owner’s Manual and Service Booklet. The records of the same to be ensured in Owner’s Manual.  Retention of maintenance service bills.

I / We have been explained the Terms and conditions, Coverage and Owner’s responsibility by the Dealer Service Marketing Executive. I wish to avail / Do not wish to avail extended warrant policy.

Customer’s Signature Dealer’s Signature 247 CAR CARE AND VALUE ADDED SERVICES Value Added Services Why are Corrosion Protection Waxes necessary? Corrosion is caused by: Water / salt water acid rain & atmospheric fallouts. Critical areas are: Cavities: joints, crevices, spot welds, underbody  Corrosion is the most important factor when we talk about the vehicle life. If you treat your car you can prolong the life.  It is very dangerous to drive around in a corroded vehicle.  The corrosion creeps onto the vehicle from the inside and from the outside. The most dangerous kind of corrosion is often not discovered until it is too late. Benefits of Anti - Rust treatment:  A professionally applied range of world class products offering real value to the new and used vehicle customer.  The treatment has been developed to withstand the harshest environmental and climatic conditions (rust. Pollutants, stone and gravel impact, etc.)  Insulate cabin space from external noises.  Expensive tin work and Denting / Painting avoided.  Higher resale value for the vehicle.  Higher safety – uncorroded vehicle  10 free checkups available

248 CAR CARE AND VALUE ADDED SERVICES TATA MOTORS has tied up with M/s Wurth, M/s Autokrom, M/s 3M India Lt d & M/s Bardahl for these world class treatment at affordable prices. These treatments are available in all authorized workshops. The Dealer Service Marketing Executive will explain to you the benefits and terms and conditions of this treatment.

I / We have been explained the Benefits, Terms and conditions and the prices of these treatments by the Dealer Service Marketing Executive. I wish to avail / Do not wish to avail extended warrant policy.

Customer’s Signature Dealer’s Signature

249 CAR CARE AND VALUE ADDED SERVICES Vehicle Exterior Enrichment

Why vehicles are painted?  For Corrosion protection of the metal surfaces.  Ease of application from other corrosion protection treatments.  Cheaper than other corrosion protection methods eg. Galvanizing, ano- dizing.  For decoration and identification. Various Environmental Hazards affecting paints Environmental hazards: destroy your vehicle's finish. Even as your new vehicle rolls off the assembly line, the paint is not protected.

The enemy Ultraviolet Rays, Pollution, Tree Sap, Bird Droppings, Car Wash Chemicals, Road Salt, Acid Rain.

Benefits: Vehicle Exterior Enrichment  Removal of medium scratches, orange peel, oxidation, dust nibs etc. & swirl marks from painted surface.  Restoration of original gloss levels, UV protection after gloss is restored.  Cleaning & dressing of tyres, Bumpers & all exterior plastic moldings/trims. TATA MOTORS has tied up with M/s Autokrom, M/s 3M & M/s Wurth for this world class treatment at affordable prices. This treatment is available in all authorized workshops. The Dealer Service Marketing Executive will explain to you the benefits and terms and conditions of this treatment.

250 CAR CARE AND VALUE ADDED SERVICES Vehicle Interior Enrichment Why protect your new car’s fabric interior?  Someone will spoil your vehicle's fabric carpet or seats.  A significant detractor from your vehicle's resale value.  A permanent stain on your vehicle's interior fabric. The enemy: Drink Spills - Food Stains - Mud - Ultraviolet Rays Pets - Traffic Benefits: Vehicle Interior Enrichment  Removal of medium stains and dirt from all interior parts of the car i.e., carpet, upholstery and roof lining.  Cleaning of windshield and all windows (inside and outside).  Dressing of all internal plastics (e.g.: door pad trims) and rubber parts.  The treatment involves cleaning and dressing of all parts of the exposed interiors.  Specialised protection for seat fabric from liquid spills. TATA MOTORS has tied up with M/s Wurth and M/s Autokrom for this world class treatment at affordable prices. This treatment is available in all authorized workshops. The Dealer Service Marketing Executive will explain to you the benefits and terms and conditions of this treatment.

I / We have been explained the Terms and conditions, Coverage and Owner’s responsibility by the Dealer Service Marketing Executive. I wish to avail / Do not wish to avail extended warrant policy.

Customer’s Signature Dealer’s Signature

251 CAR CARE AND VALUE ADDED SERVICES

252 WARRANTY - TERMS AND CONDITIONS Vehicle Warranty: Terms and conditions 5. This warranty shall not apply if the car or any part thereof is repaired or altered otherwise than in accordance with our We WARRANT each TATA HARRIER vehicle and parts thereof standard repair procedure or by any person other than from manufactured by us to be free from defect in material and our sales or service establishments, our authorized deal- workmanship subject to the following terms and conditions: ers, service centres or service points in any way so as, in 1. This warranty shall be for a period of 2 years from the date our judgment which shall be final and binding, to affect its of sale of the car or a mileage of 1, 00,000 Kms which- reliability, nor shall it apply if, in our opinion which shall be ever occurs earlier. final and binding, the car is subjected to misuse, negligence, improper or inadequate maintenance or accident or 2. Our obligation under this warranty shall be limited to repair- loading in excess of such carrying capacity as certified by ing or replacing, free of charge, such parts of the car which, us, or such services as prescribed in our Owner's Manual in our opinion, are defective, on the car being brought to us are not carried out by the buyer through our sales or service or to our dealers within the period. The parts so repaired or establishments, our authorized dealers, service centres or replaced shall also be warranted for quality and workman- service points. ship but such warranty shall be co-terminus with this original warranty. 6. This warranty shall not apply to the replacement of normal wear parts, including without limitation, drive belts, 3. Any part which is found to be defective and is replaced by hoses, wiper blades, fuses, clutch disc, brake shoes, us under the warranty shall be our property. brake pads, cables and all rubber parts (except oil seal 4. As for such parts as Tyres, Batteries, Audio and / or Video and glass run). equipment (if any), etc. not manufactured by us but sup- 7. This warranty shall not cover any inherent normal deterio- plied by other parties, this warranty shall not apply, but buy- ration of the car or any of its parts arising from the actual ers of the car shall be entitled to, so far as permissible by use of the car or any damage due to negligent or improper law, all such rights as we may have against such parties operation or storage of the car. under their warranties in respect of such parts.

253 WARRANTY - TERMS AND CONDITIONS 8. This warranty shall not apply to normal maintenance ser- other liability arising from the sale of the car or any agree- vices like oils & fluid changes, head lamps focusing, fas- ment in relation thereto. tener retightening, center hub cap/wheel cover. wheel bal- 12. The buyer shall have no other rights except those set out ancing and alignment, tyre rotation, adjustment of valve above and have, in particular, no right to repudiate the sale, clearance, fuel timing, ignition timing and consumables like or any agreement or to claim any reduction in the purchase bulbs, fuel, air & oil filters and gas leaks in case of air con- price of the car, or to demand any damages or compensa- ditioned cars. tion for losses, incidental or indirect, or inconvenience or 9. This warranty shall not apply to any damage or deteriora- consequential damages, loss of car, or loss of time, or oth- tion caused by environmental pollution or bird droppings. erwise, incurred or accrued. Slight irregularities not recognized as affecting the function or quality of the vehicle or parts, such as slight noise or vi- 13. Any claim arising from this warranty shall be recognized only if it is notified in writing to us or to our authorized bration, defects appearing only under particular or irregular dealer without any delay soon after such defects as cov- operations are items considered characteristics of the ve- ered & ascertained under this warranty. hicle. 14. This warranty is fully transferable to subsequent vehi- 10. This warranty shall be null and void if the car is subjected to abnormal use such as rallying, racing or participation in cle owner. Only unexpired remaining period of warranty applies. any other competitive sport. This warranty shall not apply to any repair or replacements as a result of accident or col- 15. We reserve our rights to make any change or modification lision. in design of the car or its parts or to introduce any improve- ment therein or to incorporate in the car any additional part 11. This warranty is expressly in lieu of all warranties, whether or accessory at any time without incurring any obligation to by law or otherwise, expressed or implied, and all other ob- incorporate the same in the cars previously sold. ligations or liabilities on our part and we neither assume, nor authorize any person to assume on our behalf, any

254 ENVIRONMENT SAFETY TATA MOTORS LTD. is committed to produce vehicles using en-  It is not necessary to rev up the engine before turning it off vironmentally sustainable technology. A number of features as it unnecessarily burns the fuel. have been incorporated in TATA MOTORS passenger vehicles Shift to higher gears as soon as possible. Use each gear which have been designed to ensure environmental compati-  upto 2/3rd of maximum engine speed. bility throughout the life cycle of the vehicle. We would like to inform you that your vehicle meets emission norms and this is  A chart indicating gear shifting speeds is given in this book. being regularly validated at the manufacturing stages. Maintenance As a user you too can protect the environment by operating your vehicle in a proactive manner. A lot depends on your driv-  Ensure that recommended maintenance is carried out on ing style and the way you maintain your vehicle. We have given the vehicle regularly at the Authorised Service Outlets. a few tips for your guidance.  As soon as you see any leakages of oil or fuel in the vehicle Driving we recommend to get it attended immediately.  Avoid frequent and violent acceleration.  Use only recommended grades and specified quantity of lubricants.  Do not carry any unnecessary weight in the vehicle as it overloads the engine. Avoid using devices requiring high  Get your vehicle checked for emission periodically by an au- power consumption during slow city traffic condition. thorised dealer.  Monitor the vehicle’s fuel consumption regularly and if  Ensure that fuel filter, oil filter and breather are checked showing rising trend get the car immediately attended at periodically and replaced, if required, as recommended by the Company’s Authorised Service Outlets. TATA MOTORS.  Switch off the engine during long stops at traffic jams or  Do not pour used oils or coolants into the sewage drains, signals. If you need to keep the engine running, avoid un- garden soil or open streams. Dispose the used filters and necessary revving it up or stopping and starting. batteries in compliance with the current legislation.

255 ENVIRONMENT SAFETY  Do not allow unauthorized person to tamper with engine 9. If the ‘Check Engine lamp’, ‘MIL’ , 'SCR' or ‘DPF’ lamp con- settings or to carry modifications on the vehicle. tinuously glows, please take the vehicle to a TATA MOTORS Authorized Dealer/Service Center.  Never allow the vehicle to run out of fuel. 10. Exhaust After Treatment System parts.  Parts like brake liners, clutch discs should be vacuum cleaned. Do not use compressed air for cleaning these 11. EMS wiring harness i.e. electrical connections to all sen- parts which may spread dust in the atmosphere. sors and actuators. While carrying out servicing or repairs of your vehicle, you This Owner’s manual contains further information on driving should pay keen attention to some of the important engine precautions and maintenance care leading to environment aggregates and wiring harness which greatly affect emis- protection. Please familiarize yourself with these aspects be- sion. These components are: fore driving. 1. Fuel injection equipment- pump, rail, injectors, nozzles and high-pressure pipes. 2. Air Intake & Exhaust system, especially for leakages. 3. Cylinder head for valve leakage. 4. All filters such as air, oil and fuel filters (check periodically). 5. Turbocharger. 6. EGR Valve & Cooler 7. Intake throttle 8. Electrical connections.

256