North State Resurfacing, Co. Tennis Court Construction Post Office Box 387 Resurfacing and Repair Wendell, NC 27591 Pavement Games Office: (919) 365-7500 Accessories Cell: (919) 210-9138 [email protected]

December 09, 2016

Cypress Island HOA Wimington, NC

Attn: Thomas Bissett

Thank you for allowing us to provide a price for resurfacing your tennis courts. Since 1990, North State Resurfacing has been constructing and resurfacing tennis courts, basketball courts and other recreational facilities across the state of North Carolina, South Carolina and Virginia.

Our clients include country clubs, homeowners, municipalities, schools, universities, military bases and government installations. References can be furnished upon request.

The base price on page one of our proposal is for a standard resurfacing which reflects the work required to refurbish your facility.

Page two of our proposal contains various options which allow you to customize the resurfacing project to meet your needs. For example; if your courts have structural cracks in the asphalt, you may choose to have the Super Seal, crack repair system installed, which provides a guarantee against the reappearance of the existing cracks. Or, there may be an emphasis on youth oriented programs at your facility in which case, you might decide to have Quick Start lines installed.

There are many other options available that are not listed. We can also install basketball goals and pavement games such as hopscotch, four square and bean bag toss.

Once again, thank you for the opportunity and please contact me with any questions that you may have.

Sincerely,

Drewry C. Alford Project Manage & Estimator

NORTH STATE RESURFACING, CO. PROPOSAL Post Office Box 387 Proposal number: 6955 Wendell NC 27591 Page number: 1 of 2 Phone: (919) 365-7500 Date: 12-09-2016 www.northstateresurfacing.com

PROPOSAL SUBMITTED TO: Thomas Bissett WORK TO BE PERFORMED AT:

Name: Blue Atlantic Management Name: Cypress Island

Address: 5219 Oleander Dr., Suite 101 Address: Wilmington, NC Wilmington, NC

Phone: 910-452-9823 Job Site:

We hereby propose to furnish the materials and perform the labor necessary for the completion of: The repair and resurfacing of one (1) all-weather tennis court with overall dimensions of approximately 60' x 120'. North State Resurfacing uses only the finest materials available, manufactured by DECOTURF, surface of the US Open since 1978. Surface preparation: 1. Clean and scrape court of all loose material, dirt, foreign matter and debris. 2. Remove vegetation from cracks and the perimeter of the court. 3. After vegetation has been removed, burn root growth with a propane burner then treat with herbicide. 4. Thoroughly flood the entire court surface if necessary, allow to drain for one hour then locate and mark birdbaths to be patched. 5. Patch any depressions holding more than 1/8" of water after being allowed to drain for one hour using an acrylic patch material. Note: Only one attempt shall be made to patch depressions. Any additional patching will be an extra charge of time and materials. 6. Patch any structural cracks, dings, etc. in the asphalt surface using an acrylic patching material. 7. Patch two areas located at the corners of the court, closest to the golf course, where the asphalt has settled. Areas shall be patched using concrete, then overlayed with Fortress 97423, Polyester Fabric. Patches to be level and smooth with the surrounding surface. Surfacing: 1. Apply one (1) coat of California 920-29, sand filled acrylic resurfacer to the entire court surface as a filler coat following the manufacturer’s directions and application rates. 2. Apply one (1) coat of DecoBase I 920-05, sand filled acrylic latex compound, tinted with DecoColor MP 920-27 to the entire court surface as a texture coat following the manufacturer’s directions and application rates. 3. Apply one (1) coat of DecoColor MP Classic 920-27, acrylic color concentrate to the entire court surface as a finish coat following the manufacturer’s directions and application rates. Playing lines: 1. Layout, tape and hand paint 2" wide playing lines using Hi-Hide 920-22, textured acrylic white line paint. Layout to conform to U.S.T.A. specifications. 2. Masking tape shall be sealed prior to painting using California Line Rite. Completion: 1. Clean net posts and paint using Rustoleum spray paint. 2. Hang net to regulation height and tension. 3. Clean job site, dispose of all debris and leave court ready for play. Note: Owner shall provide potable water and electricity to within 200' of court. Suitable access to the courts shall be provided along with an area for washing our equipment. Color: As desired from the “Colorizer” page, found at www.northstateresurfacing.com. (Additional charges may apply to certain colors). Guarantee: Two (2) years against defective materials and labor. The repair of cracks are not guaranteed. Cracks may reappear within a short period of time. Standing water may only be minimized due to inadequate slope/drainage. The appearance of rust stains are not guaranteed due to asphalt content.

All material is guaranteed to be as specified, and the above work to be performed in accordance with the drawings and specifications submitted for above work and completed in a substantial workmanlike manner for the sum of:

Nine thousand seven hundred fifty and no/100 DOLLARS ( $9,750.00 )

with payments to be made as follows: Due upon completion. Unpaid balances are subject to finance charges of 1.5% per month.

Any alteration or deviation from above specifications involving extra costs will be RESPECTFULLY SUBMITTED BY: North State Resurfacing, Co. executed only upon written order, and will become an extra charge over and above the estimate. All agreements contingent upon strikes, accidents, or delays beyond PER: Michael A. Alford our control.

NOTE: This proposal may be withdrawn by us if not accepted within 30 days.

ACCEPTANCE OF PROPOSAL The above prices, specifications and conditions are satisfactory and are hereby accepted. You are authorized to do the work as specified. Payments will be made as outlined above.

SIGNATURE:______DATE:______

COLOR SELECTIONS: Inbounds______Perimeter______

NORTH STATE RESURFACING, CO. PROPOSAL Post Office Box 387 Proposal number: 6955 Wendell, NC 27591 Page number: 2 of 2 Phone: (919) 365-7500 Date: 12-9-2016 www.northstateresurfacing.com

PROPOSAL SUBMITTED TO: Thomas Bissett WORK TO BE PERFORMED AT:

Name: Blue Atlantic Management Name: Cypress Island

Address: 5129 Oleander Dr., Suite 101 Address: Wilmington, NC Wilmington, NC

Phone: 910-452-9823 Job Site:

We hereby propose to furnish the materials and perform the labor necessary for the completion of: The repair and resurfacing of one (1) all-weather tennis court with overall dimensions of approximately 60' x 120'.

Options:

Option #1: Install approximately 100 linear feet of Super Seal crack repair to all major structural cracks. Cracks treated with the Super Seal system are guaranteed not to reappear for two (2) years. All other areas of the court are not guaranteed. New cracks may form within a short period of time. Occasionally this type of repair may cause dead spots or buckling of the surface, this should be considered normal………………………………………...... $ 1,450.00** **Price based on measurements taken December 6, 2016. Any additional cracks that may form can be treated with the Super Seal system at a rate of $14.50 per linear foot. Option #2: Install Fortress 97423, Polyester Fabric to the entire court surface. Although there is no guarantee associated with this system, it strengthens the surface to help prevent the appearance of cracks...... Additional $5,525.00 Option #3: Provide and install Douglas TN-30DH net including center straps. (Four year warranty)...... $270.00 www.douglas-sports.com Item #30029 Option #4: Provide and install Douglas E-Z net posts with external wind reel and removable handle...... $320.00* www.douglas-sports.com Item #63021 * Note: Price good only if existing net posts are set in sleeves and can be easily removed. Option #5: Court Caddy waste basket and tray. (Available in green or black)...... $70.00 www.douglas-sports.com Item #34745 Option #6: Deluxe Court side bench, constructed from extruded high density Polyurethane, 5' in length.. (Available in green, blue or white) www.douglas-sports.com Item #34765...... $400.00 each. Option #7: Layout, tape and hand paint Pickleball playing lines...... $300.00 Option #8: Scorekeeper with high visibility game numbers. Set includes game numbers, set numbers, dry erase pen and nameplates. Attaches to net post...... $70.00 www.douglas-sports.com Item#34754 Option #9: Rol-Dri water remover with seamless foam roller...... $85.00 each. www.douglas-sports.com Item #34734 Option #10: The Outpost, maintenance free outdoor message display board. (Available in white, green, black or brown)...... $625.00 each. www.douglas-sports.com Item # 33870

Other accessories are available. Please contact us for pricing.

All Options are intended to be an addition to the base price on page #1.

Any alteration or deviation from above specifications involving extra costs will be RESPECTFULLY SUBMITTED BY: North State Resurfacing, Co. executed only upon written order, and will become an extra charge over and above the estimate. All agreements contingent upon strikes, accidents, or delays beyond PER: Michael A. Alford our control.

NOTE- This proposal may be withdrawn by us if not accepted within 30 days.

ACCEPTANCE OF PROPOSAL The above prices, specifications and conditions are satisfactory and are hereby accepted. You are authorized to do the work as specified. Payments will be made as outlined above.

SIGNATURE:______DATE:______You choose the colors. We make them Green.

DecoTurf is proud to announce that our DecoColor color coatings have been certified as GreenWise by the Coatings Research Group Inc.

DecoColor has been certified by the Coatings Research Group, Incorporated to meet environmental determined performance standards established by the CRGI’s ISO-accredited facility for specific product types and to meet or exceed the VOC requirements of LEED for most paints and coatings applications. This product is environmentally preferred over traditional paints and coatings.

Visit www.greenwisepaints.com to view product standards.

DecoTurf, Cushioned Tennis Surface of Champions since 1978

150 Dascomb Rd. Andover MA 01810 800-Deco-1ST * www.decoturf.com

Now you can follow us on

dirt, debris and loose impediments. Cracks should be blown ® clean with an air compressor. After cleaning, apply Crack Filler California 64061 to fill cracks. Consult the data sheet for application information. 4.4 Surface Imperfections Acrylic Resurfacer Before application of primers or Acrylic Resurfacer, the court surface shall be flooded with water and allowed to drain. Any depressions capable of submerging a U.S. five-cent piece 920-29 4200 after one hour should be marked with chalk, not crayon or a grease pencil. These areas must be allowed to thoroughly ACRYLIC BASE FOR RECREATIONAL SURFACES dry. Once dried, a patch must be applied to the marked area. For patching products and mix designs, please refer to 1.0 MATERIAL DESCRIPTION the product data sheet for Court Patch Binder 920-39. Acrylic Resurfacer is a concentrated 100% acrylic latex binder designed for field mixing with silica sand and is to be 4.5 Priming applied to recreational surfaces constructed of hot-mix • Priming of asphalt surfaces is only necessary if existing asphalt or Portland cement concrete. asphalt is too badly weathered to establish a strong bond with the Acrylic Resurfacer. In the case of 2.0 INTENDED USE extremely oxidized asphalt surfaces, contact your Deco Acrylic Resurfacer is intended for preparing new asphalt or Area Manager. concrete surfaces as well as existing acrylic surfaces for color coating. • When applying Acrylic Resurfacer to new concrete surfaces, a primer is necessary to improve adhesion. 3.0 PHYSICAL PROPERTIES Deco Surfacing Systems offers California Ti-Coat, a Color: Black two-package water based epoxy primer. Consult the Coverage Rate (undiluted) 0.06 gallons/sq. yd. respective data sheets for proper application. Weight per gallon: 8.8 lbs. Curing conditions: 70°F & 50% relative humidity • If the concrete surface has been previously coated with Estimated cure time: 2 hours acrylic material, no priming is necessary. Minimum ambient, surface & product installation temperature: 60° and rising 5.0 MIXING INSTRUCTIONS Note: Low temperatures or high humidity will increase drying The following mix has been found to be satisfactory for time drastically. Maximum surface temperature = 140° F. average surface conditions: Acrylic Resurfacer 55 gallons 30 gallons 4.0 SURFACE PREPARATION Silica Sand (60 - 80 Mesh) 600-900 lb. 325-400 lb. 4.1 Base Construction Clean potable water 20-40 gallons 11 – 22 gallons Surface must meet or exceed the American Sports Builders Association (ASBA) applicable Guidelines. Upgrading and 5.1 Sand Mix recoating previously colored surfaces requires the surface Do not use sand containing clay, silt, ferrous metals or and base construction to be in sound condition and in salt. The outcome of the Resurfacer mix depends heavily on compliance with the applicable ASBA Guidelines. what type of sand you chose. Our specifications are based on 60-80 mesh sand. The addition of the silica sand should 4.2 Substrate Cure Requirements be done slowly, under agitation. New hot-mix asphalt surfaces must be allowed a minimum of 14 days cure time before application of Acrylic Resurfacer. 5.2 Water Mix For new, Portland cement concrete surfaces, a minimum of In no case should Acrylic Resurfacer be diluted more than 28 days cure time is required. After 28 days, new concrete three (3) parts Acrylic Resurfacer to two (2) parts water. The must be acid-etched with either phosphoric or muriatic acid. quantity of water required will vary with moisture content and Application may begin thereafter. gradation of the sand and the consistency needed for good application characteristics. 4.3 Surface Condition The surface on which Acrylic Resurfacer is to be applied must be smooth, free of dirt, loose or flaking paint, oily materials or chemical residues, vegetation of any sort and any other debris or foreign matter that may prevent the 5.3 Resurfacing Mix proper product adhesion. Thoroughly rout existing cracks of Acrylic Resurfacer 03/2008

After the addition of sand and water to the Acrylic Resurfacer Drying times are retarded by high humidity, cool concentrate, thorough mixing is required. A mechanical drill temperatures or lack of air movement. This is particularly mixer is recommended and mixture should be stirred until important to note when installing indoors, where all three homogeneous. Periodic mixing should take place as the job factors are often very pronounced. progresses to ensure consistent application. 9.5 Keep From Freezing 6.0 GUIDE TO APPLICATION Acrylic Resurfacer is a water-based acrylic system and it 6.1 System Recommendations must be kept from freezing during storage or in transit. If you Deco recommends one 1-2 coats of Acrylic Resurfacer prior receive product you suspect may have been exposed to to the application of any Deco Surfacing System. If using the freezing temperatures, consult your Deco Surfacing Systems Street Ice system, a minimum of two (2) coats is Representative for proper handling instructions. recommended. See Street Ice S/I-3 for further information. 10.0 LIMITED WARRANTY 6.2 Installation The Company warrants that the products to be delivered and Using a flexible rubber squeegee, apply Acrylic Resurfacer sold there under are the kind and quality described in its mix parallel to one of the sides of the surface area. Care specifications and no other warranty, except of title, is should be taken not to leave ridges where adjoining expressed or implied. All other warranties and/or liabilities, applications overlap. Under hot conditions, application is including consequential damages, are specifically excluded improved by keeping surface damp with a fine mist water whether the directions for a product’s use are followed or not. spray. Never allow water to pool on the surface. Notification of any apparent defect or defects shall be made promptly in writing to the Company. Should any product 6.3 Drying and Cure Time (unless sold as is) prove, upon our inspection, to be defective Acrylic Resurfacer must be allowed to cure a minimum of 2 in workmanship or materials in accordance with the hours before applying acrylic coatings. specifications, the Company will replace the product or refund the purchase price. No person has the authority of 7.0 COVERAGE the Company to make or accept any other warranty, liability, The undiluted coverage rate is approximately 0.06 gallons or conditions on the Company’s behalf. If the above stated per square yard, per application conditions of this warranty are unacceptable, the purchaser may return, at his expense, all unopened packages, bags or 8.0 CLEAN-UP containers for credit within 30 days from the date of All equipment can be cleaned with water if clean-up occurs purchase. immediately after application. 11.0 FOR FURTHER INFORMATION 9.0 LIMITATIONS California Products Corporation manufactures many different 9.1 Surface Limitations recreational surface products. For additional information Acrylic Resurfacer is limited to application on hot-mix asphalt contact us at: and Portland cement concrete recreational surfaces. Deco Surfacing Systems does not recommend, nor authorize the Deco Surfacing Systems application of Acrylic Resurfacer on any other surfaces a division of California Products Corporation without prior approval from your Deco Area Manager. 150 Dascomb Road Andover, MA 01810 9.2 Weather Limitations (800) 332-6178 No part of the construction involving the Deco Surfacing [email protected] System should be conducted during rainfall, or when rainfall is imminent. The air temperature must be at least 60ºF and rising. Do not apply when surface temperature is above 140ºF.

9.3 Do Not Over Dilute The maximum dilution ratio is 3:2. Over dilution will cause streaking, foaming, adhesion failure, sand fall-out and poor overall durability of the coating.

9.4 Indoor Application Drying

Acrylic Resurfacer 03/2008

DecoBase I™ 4.4 Surface Imperfections • If DecoBase I is the first step to coating a newly constructed acrylic system, the surface must be prepared with Acrylic Resurfacer first. Please refer to 920-05 the data sheet Acrylic Resurfacer 920-29. ACRYLIC TEXTURE FOR RECREATIONAL SURFACES • If DecoBase I is the first step in recoating an existing 1.0 MATERIAL DESCRIPTION acrylic system, the surface should be flooded with water DecoBase I™ 920-05 coating is a sand filled, 100% acrylic and allowed to drain prior to application of DecoBase I. latex compound designed for squeegee application to Any depressions capable of submerging a U.S. five- relatively smooth surfaces. It is supplied as a non-pigmented cent piece after one hour should be marked with chalk, concentrate to be tinted with DecoColor® MP 920-27 and not crayon or a grease pencil. These areas must then diluted with water prior to use. DecoBase I coating results in be allowed to thoroughly dry. Once dried, a patch must a dense, durable textured surface and adds firm thickness to be applied to the marked areas. For patching the color system. information, please refer to the product data sheet for Acrylic Patch Binder 920-39. 2.0 INTENDED USE DecoBase I is designed to impart the desired texture that If DecoBase I application follows the DecoTurf Cushion controls the speed of play. It fills minor surface irregularities System, do not flood the court. Proceed with Mixing and provides a tough, wear-resistant coating which imparts a Instructions. consistent texture across the playing field. 5.0 MIXING INSTRUCTIONS 3.0 PHYSICAL PROPERTIES The following mixes have been found to be satisfactory for Color: Neutral average surface conditions: Coverage Rate (undiluted): .06 gallons/square yard, DecoBase I 920-05 55 gallons .0865 gallons/square yard DecoColor ® MP 920-27 15 gallons over DecoBase II Clean Potable Water 23 gallons Weight per gallon: 12.0 lbs. Curing conditions: 70°F & 50% relative humidity After the addition of water thorough mixing is required. A Estimated cure time: 4 hours mechanical drill mixer is recommended and mixture should be stirred until homogeneous. Periodic mixing should take Minimum ambient, surface & place as the job progresses to ensure consistent application. product installation temperature: 60° and rising

Note: Low temperatures & high humidity will increase drying 6.0 GUIDE TO APPLICATION time drastically. Maximum surface temperature = 140°F. 6.1 System Recommendation Two (2) applications have proven to give excellent 4.0 SURFACE PREPARATION performance results. Deco recommends the use of Acrylic 4.1 Base Construction Resurfacer 920-29 prior to the application of any Deco Surface must meet or exceed the American Sports Builders Surfacing System. See the data sheet on Acrylic Resurfacer Association (ASBA) applicable Guidelines. Upgrading and for further information. recoating previously colored surfaces requires the surface and base construction to be in sound condition and in 6.2 Installation compliance with the applicable ASBA Guidelines. Using a flexible rubber squeegee, 50 or 70 durometer, apply DecoBase I mix parallel to one of the sides of the area to be 4.2 Substrate Cure Requirements coated. Care should be taken not to leave ridges where New hot-mix asphalt surfaces must be allowed to cure for a adjoining applications overlap. Application in hot conditions minimum of 14 days prior to application of DecoBase I. For is improved by keeping surface damp with a fine mist water new Portland cement concrete surfaces, a minimum of 28 spray. Additional applications should be installed at 90° to days cure time is required. the previous application.

4.3 Surface Condition The surface upon which DecoBase I is to be applied must be smooth, free of dirt, loose or flaking paint, oily materials or 6.3 Drying and Cure Time chemical residues, vegetation of any sort and any other DecoBase I must be allowed to dry 4 hours before another debris or foreign matter that may prevent the proper product coating can be applied, assuming 70°F temperatures and adhesion. DecoBase I 10/2005

50% relative humidity. Low temperatures and high humidity defective in workmanship or materials in accordance with the will increase drying time dramatically. specifications, the Company will replace the product or refund the purchase price. No person has the authority of 7.0 COVERAGE the Company to make or accept any other warranty, liability, The undiluted coverage rate is approximately 0.06 gallons or conditions on the Company’s behalf. If the above stated per square yard, per application (150 square feet per gallon). conditions of this warranty are unacceptable, the purchaser If applied over DecoBase II the undiluted coverage rate is may return, at his expense, all unopened packages, bags or approximately .0865 gallons per square yard, per application containers for credit within 30 days from the date of (105 square feet per gallon). purchase.

8.0 CLEAN-UP 11.0 FOR FURTHER INFORMATION If clean-up occurs immediately after application, water will California Products Corporation manufactures many different remove acrylics from equipment. recreational surfaces products. For additional information contact us at: 9.0 LIMITATIONS 9.1 Surface Limitations Deco Surfacing Systems DecoBase I is limited to application on hot-mix asphalt and a division of California Products Corporation Portland cement concrete recreational surfaces. Please see 150 Dascomb Road the DecoColor installation guideline for new and existing Andover, MA 01810 asphalt and concrete surfaces for more information. Deco (800) 332-6178 Surfacing Systems does not recommend, nor authorize the [email protected] application of DecoBase I on any other surfaces without prior approval from your Deco Area Manager.

9.2 Weather Limitations No part of the construction involving the Deco Surfacing System should be conducted during rainfall, or when rainfall is imminent. The air temperature must be at least 60ºF and rising. Do not apply when surface temperature is above 140ºF.

9.3 Do Not Over Dilute Over dilution can cause streaking, foaming, adhesion failure, sand fall-out and poor overall durability of the coating.

9.4 Indoor Application Curing Drying times are retarded by high humidity, cool temperatures or lack of air movement. This is particularly important to note when installing indoors, where all three factors are often very pronounced.

9.5 Keep From Freezing DecoBase I is a water-based acrylic system and it must be kept from freezing during storage or in transit. If you receive product you suspect may have been exposed to freezing temperatures, consult your Deco Area Manager for proper handling instructions.

10.0 LIMITED WARRANTY The Company warrants that the products to be delivered and sold there under are the kind and quality described in its specifications and no other warranty, except of title, is expressed or implied. All other warranties and/or liabilities, including consequential damages, are specifically excluded whether the directions for a product’s use are followed or not. Notification of any apparent defect or defects shall be made promptly in writing to the Company. Should any product (unless sold as is) prove, upon our inspection, to be DecoBase I 10/2005 New hot-mix asphalt surfaces must be allowed 14 days minimum cure time prior to application of Deco products.  DecoColor MP For new Portland cement concrete surfaces, a minimum of 28 days cure time is required. After 28 days, new concrete must be acid-etched with either phosphoric or muriatic acid. Application may begin thereafter. Classic 4.3 Surface Condition The surface on which DecoColor is to be applied must be 920-27 smooth, free of dirt, loose or flaking paint, oily materials or chemical residues, vegetation of any sort and any other ACRYLIC COLOR FOR RECREATIONAL SURFACES debris or foreign matter that may prevent the proper product adhesion. Thoroughly rout existing cracks of dirt, debris and 1.0 MATERIAL DESCRIPTION loose impediments. Cracks should be blown clean with an air DecoColor MP Classic 920-27 is a full bodied, high compressor. Consult the data sheet 64061 Deco Crack Filler for performance acrylic latex coating. It is fortified with specially application information. selected fillers and is pigmented in eleven standard colors. Special colors are possible upon request, however minimum 4.4 Surface Imperfections quantities do apply. DecoColor MP Classic offers the Before application of primers or Acrylic Resurfacer, the court advantage of using one product for the texture courses and surface shall be flooded with water and allowed to drain. the finish course. Any depressions capable of submerging a U.S. five-cent piece after one hour should be marked with chalk, not crayon 2.0 INTENDED USE or a grease pencil. These areas must be allowed to DecoColor MP Classic is intended for use as a texture thoroughly dry. Once dried, a patch must be applied to the and/or top coat for recreational surfaces. Job mixing gives marked area. For patching products and mix designs, the installer the flexibility to meet individual job conditions. please refer to the product data sheet for Acrylic Patch The finish texture and speed of play can be modified through Binder 920-39. the size and amount of sand used in the mix. This product allows the contractor the flexibility to select and add the 4.5 Priming proper sand to meet specific job requirements. Priming of asphalt surfaces is only necessary if existing asphalt is too badly weathered to establish a strong bond 3.0 PHYSICAL PROPERTIES with the Acrylic Resurfacer. In the case of extremely oxidized Classic Colors: US Open Blue, Spring Green, asphalt surfaces, contact your Deco Area Manager. Winter Green, Forest Green, Summer Red, Royal Blue, When applying Acrylic Resurfacer to new concrete surfaces, America’s Red Clay, a primer is necessary to improve adhesion. Deco Surfacing Tour Purple, Adobe Tan, Systems offers California Ti-Coat 63903 & 63904, a two- package water based epoxy primer. Consult the respective Olympic Blue, & Stone Gray data sheets for proper application. Weight per gallon: 10.5 lbs.

Curing conditions: 70° F & 50% relative humidity If the concrete surface has been previously coated with To top coat: 4 hours acrylic material, no priming is necessary. Estimated curing time: 24 hour minimum Minimum ambient, surface & 5.0 MIXING INSTRUCTIONS product installation temperature: 60°F and rising The following mixes have been found to be satisfactory for Note: Low temperatures or high humidity will increase drying average surface conditions: time drastically. Maximum surface temperature = 140° F. 5.1 Texture Course 4.0 SURFACE PREPARATION DecoColor MP Classic 920-27 55 gal 30 gal 4.1 Base Construction Clean potable water 27 gal 15 gal Surface must meet or exceed the American Sport Builders Silica Sand (60-90 mesh) 440 lb 240 lb Association (ASBA) applicable Guidelines. Upgrading and NOTE: For a slower ball bounce and rougher texture, one or recoating previously colored surfaces requires the surface more texture courses may be installed in place of the finish and base construction to be in sound condition and in course. compliance with the applicable ASBA Guidelines.

5.2 Finish Course 4.2 Substrate Cure Requirements DecoColor MP Classic 920-27 55 gal 30 gal DecoColor MP Classic 10/2005 Clean potable water 38 gal 20 gal 9.0 LIMITATIONS NOTE: For a slower ball bounce and rougher texture, one or 9.1 Surface Limitations more texture courses may be installed in place of the finish DecoColor MP is limited to application on hot-mix asphalt course. and Portland cement concrete recreational surfaces. Please see Deco installations guidelines fro new and existing 5.3 Mixing asphalt and concrete surfaces for more information. Deco Do not use sand containing clay, silt, ferrous metals or Surfacing Systems does not recommend, nor authorize the salt. The outcome of the texture course depends heavily on application of DecoColor MP on any other surfaces without what type of sand you chose. Deco’s specifications are prior approval from your Deco Area Manager. based on 60-90 mesh sand. Please submit your sand samples to the California Products Research and 9.2 Weather Limitations Development laboratory for analysis and approval before No part of the construction involving the Deco Surfacing mixing with DecoColor MP Classic. Sand should be slowly System should be conducted during rainfall, or when rainfall added to undiluted MP followed by the addition of water. A is imminent. The air temperature must be at least 60ºF and mechanical mixer is recommended and mixture should be rising. Do not apply when surface temperature is above stirred until homogeneous. Periodic mixing should take place 140ºF. as the job progresses to ensure consistent application. 9.3 Do Not Over Dilute 6.0 GUIDE TO APPLICATION The maximum dilution ratio for the Texture Course is two (2) 6.1 System Recommendation parts DecoColor to one (1) part water. The maximum Two (2) texture course applications and one (1) finish course dilution ratio for the Finish Course is three (3) parts has proven to give excellent performance results. Deco DecoColor to two (2) parts water. Over dilution will cause recommends the use of Acrylic Resurfacer 920-29 prior to streaking, foaming, adhesion failure, sand fall-out and poor the application of DecoColor. See the data sheet on Acrylic overall durability of the coating. Resurfacer for more information. 9.4 Indoor Application Drying 6.2 Installation Drying times are retarded by high humidity, cool Using a flexible rubber squeegee, 50 or 70 durometer, apply temperatures or lack of air movement. This is particularly DecoColor MP Mix parallel to one of the sides of the area to important to note when installing indoors, where all three be coated. Care should be taken not to leave ridges where factors are often very pronounced. adjoining applications overlap. Applications in hot conditions are improved by keeping surface damp with a fine mist water 9.5 Keep From Freezing spray. No pooling should be allowed. Additional DecoColor MP 920-27 is a water-based acrylic system and it applications should be installed at 90° to the previous must be kept from freezing during storage or in transit. If you application. receive product you suspect may have been exposed to freezing temperatures, consult your Deco Surfacing Systems 6.3 Drying and Cure Time Representative for proper handling instructions. DecoColor MP must be allowed to dry for 4 hours between coating applications. Completed projects should be allowed 10.0 LIMITED WARRANTY 24 hours before releasing to play. The Company warrants that the products to be delivered and sold there under are the kind and quality described in its specifications 7.0 COVERAGE and no other warranty, except of title, is expressed or implied. All other warranties and/or liabilities, including consequential damages, 7.1 Texture Course are specifically excluded whether the directions for a product’s use The undiluted coverage rate is approximately 0.05 gallons are followed or not. Notification of any apparent defect or defects per square yard, per application (180 square feet per gallon). shall be made promptly in writing to the Company. Should any product (unless sold as is) prove, upon our inspection, to be 7.2 Finish Course defective in workmanship or materials in accordance with the The undiluted coverage rate is approximately 0.04 gallons specifications, the Company will replace the product or refund the per square yard, per application (225 square feet per gallon). purchase price. No person has the authority of the Company to make or accept any other warranty, liability, or conditions on the 8.0 CLEAN-UP Company’s behalf. If the above stated conditions of this warranty All equipment can be cleaned with water if clean-up occurs are unacceptable, the purchaser may return, at his expense, all immediately after application. unopened packages, bags or containers for credit within 30 days from the date of purchase.

11.0 FOR FURTHER INFORMATION

California Products manufactures many different recreational

surfaces products. For additional information contact us at:

DecoColor MP Classic 10/2005

Deco Surfacing Systems a division of California Products Corporation 150 Dascomb Road Andover, MA 01810 (800) 332-6178 [email protected]

DecoColor MP Classic 10/2005

Hi-Hide Line 5.0 MIXING INSTRUCTIONS Hi-Hide Line Paint comes ready to apply. Only gentle stirring is necessary. DO NOT DILUTE.

Paint 920-22 6.0 GUIDE TO APPLICATION 6.1 System Recommendations One or two (1-2) applications has proven to give excellent 6020 coverage.

TEXTURED OR NON-TEXTURED 6.2 Application Apply Hi-Hide Line Paint to the clean, dry, color coated XTERIOR NTERIOR INE ARKING AINT OR E /I L M P F surface by brush, roller, airless spray or special marking ATHLETIC SURFACES equipment. Apply tape to both sides of the area to be striped. Apply a primer coat of ClearGlo or the final acrylic 1.0 MATERIAL DESCRIPTION color coating over the inside edges of the tape. This will seal A highly reflective 100% acrylic marking paint for use over the tape to the acrylic surface and prevent the Hi-Hide Line any bituminous surface, or acrylic color coating system in Paint from bleeding under the tape. recreational or light traffic areas. Hi-Hide Line Paint will not cause cracking, crazing, peeling, or deterioration to asphalt 6.3 Drying and Cure Time that is typical of solvent-type traffic paints. Hi-Hide Line Paint must be allowed to dry for 4 hours between coating applications. Completed projects should be 2.0 INTENDED USE allowed 24 hours before releasing to play. For the striping of color-coated recreational surfaces or any asphalt or concrete surface in light traffic areas, such as 7.0 COVERAGE Tennis Courts, Play Areas, Curbs and Berms, Running Approximately one gallon of Hi-Hide Line Paint is required Tracks, & Parking Lots per standard U.S.T.A. sanctioned tennis court per application. 3.0 PHYSICAL PROPERTIES Color: White, Yellow, Red, Blue, 8.0 CLEAN-UP Green, Orange, & Black All equipment can be cleaned with water if clean-up occurs Weight per gallon: 11.0 lbs. immediately after application. Curing conditions: 70° F & 50% relative humidity 9.0 LIMITATIONS To top-coat: 4 hours 9.1 Surface Limitations Estimated cure time: 24 hours Hi-Hide Line Paint is limited to application on hot-mix asphalt Minimum ambient, surface & and Portland cement concrete recreational surfaces. Not for product installation temperature: 60° and rising application on general use roadways subjected to skidding Note: Low temperatures or high humidity will increase drying tires, snowplows, or chains. time drastically. Maximum surface temperature = 140° F. 9.2 Weather Limitations 4.0 SURFACE PREPARATION No part of the construction involving the Deco Surfacing 4.1 Substrate Cure Requirements System should be conducted during rainfall, or when rainfall New hot-mix asphalt surfaces must be allowed 14 days is imminent. The air temperature must be at least 60ºF and minimum cure time prior to application of Hi-Hide Line Paint. rising. Do not apply when surface temperature is above For new Portland cement concrete surfaces, a minimum of 140ºF. 28 days cure time is required. 9.3 Do Not Dilute 4.2 Surface Condition The surface upon which Hi-Hide Line Paint is to be applied 9.4 Indoor Application Curing must be smooth, free of dirt, loose or flaking paint, oily Drying times are retarded by high humidity, cool materials or chemical residues, vegetation of any sort and temperatures or lack of air movement. This is particularly any other debris or foreign matter that may prevent the important to note when installing indoors, where all three proper product adhesion. factors are often very pronounced.

Hi-Hide Line Paint 03/2008

9.5 Keep From Freezing Hi-Hide Line Paint is a water-based acrylic and it must be kept from freezing during storage or in transit. If you receive product you suspect may have been exposed to freezing temperatures, consult your Deco Area Manager for proper handing instructions.

10.0 LIMITED WARRANTY The Company warrants that the products to be delivered and sold there under are the kind and quality described in its specifications and no other warranty, except of title, is expressed or implied. All other warranties and/or liabilities, including consequential damages, are specifically excluded whether the directions for a product’s use are followed or not. Notification of any apparent defect or defects shall be made promptly in writing to the Company. Should any product (unless sold as is) prove, upon our inspection, to be defective in workmanship or materials in accordance with the specifications, the Company will replace the product or refund the purchase price. No person has the authority of the Company to make or accept any other warranty, liability, or conditions on the Company’s behalf. If the above stated conditions of this warranty are unacceptable, the purchaser may return, at his expense, all unopened packages, bags or containers for credit within 30 days from the date of purchase.

11.0 FOR FURTHER INFORMATION California Products Corporation manufactures many different recreational surfaces products. For additional information contact us at:

Deco Surfacing Systems a division of California Products Corporation 150 Dascomb Road Andover, MA 01810 (800) 332-6178 [email protected]

Hi-Hide Line Paint 03/2008

dirt, debris and loose impediments. Cracks should be blown ® clean with an air compressor. After cleaning, apply Crack Filler California 64061 to fill cracks. Consult the data sheet for application information. 4.4 Surface Imperfections Acrylic Resurfacer Before application of primers or Acrylic Resurfacer, the court surface shall be flooded with water and allowed to drain. Any depressions capable of submerging a U.S. five-cent piece 920-29 4200 after one hour should be marked with chalk, not crayon or a grease pencil. These areas must be allowed to thoroughly ACRYLIC BASE FOR RECREATIONAL SURFACES dry. Once dried, a patch must be applied to the marked area. For patching products and mix designs, please refer to 1.0 MATERIAL DESCRIPTION the product data sheet for Court Patch Binder 920-39. Acrylic Resurfacer is a concentrated 100% acrylic latex binder designed for field mixing with silica sand and is to be 4.5 Priming applied to recreational surfaces constructed of hot-mix • Priming of asphalt surfaces is only necessary if existing asphalt or Portland cement concrete. asphalt is too badly weathered to establish a strong bond with the Acrylic Resurfacer. In the case of 2.0 INTENDED USE extremely oxidized asphalt surfaces, contact your Deco Acrylic Resurfacer is intended for preparing new asphalt or Area Manager. concrete surfaces as well as existing acrylic surfaces for color coating. • When applying Acrylic Resurfacer to new concrete surfaces, a primer is necessary to improve adhesion. 3.0 PHYSICAL PROPERTIES Deco Surfacing Systems offers California Ti-Coat, a Color: Black two-package water based epoxy primer. Consult the Coverage Rate (undiluted) 0.06 gallons/sq. yd. respective data sheets for proper application. Weight per gallon: 8.8 lbs. Curing conditions: 70°F & 50% relative humidity • If the concrete surface has been previously coated with Estimated cure time: 2 hours acrylic material, no priming is necessary. Minimum ambient, surface & product installation temperature: 60° and rising 5.0 MIXING INSTRUCTIONS Note: Low temperatures or high humidity will increase drying The following mix has been found to be satisfactory for time drastically. Maximum surface temperature = 140° F. average surface conditions: Acrylic Resurfacer 55 gallons 30 gallons 4.0 SURFACE PREPARATION Silica Sand (60 - 80 Mesh) 600-900 lb. 325-400 lb. 4.1 Base Construction Clean potable water 20-40 gallons 11 – 22 gallons Surface must meet or exceed the American Sports Builders Association (ASBA) applicable Guidelines. Upgrading and 5.1 Sand Mix recoating previously colored surfaces requires the surface Do not use sand containing clay, silt, ferrous metals or and base construction to be in sound condition and in salt. The outcome of the Resurfacer mix depends heavily on compliance with the applicable ASBA Guidelines. what type of sand you chose. Our specifications are based on 60-80 mesh sand. The addition of the silica sand should 4.2 Substrate Cure Requirements be done slowly, under agitation. New hot-mix asphalt surfaces must be allowed a minimum of 14 days cure time before application of Acrylic Resurfacer. 5.2 Water Mix For new, Portland cement concrete surfaces, a minimum of In no case should Acrylic Resurfacer be diluted more than 28 days cure time is required. After 28 days, new concrete three (3) parts Acrylic Resurfacer to two (2) parts water. The must be acid-etched with either phosphoric or muriatic acid. quantity of water required will vary with moisture content and Application may begin thereafter. gradation of the sand and the consistency needed for good application characteristics. 4.3 Surface Condition The surface on which Acrylic Resurfacer is to be applied must be smooth, free of dirt, loose or flaking paint, oily materials or chemical residues, vegetation of any sort and any other debris or foreign matter that may prevent the 5.3 Resurfacing Mix proper product adhesion. Thoroughly rout existing cracks of Acrylic Resurfacer 03/2008

After the addition of sand and water to the Acrylic Resurfacer Drying times are retarded by high humidity, cool concentrate, thorough mixing is required. A mechanical drill temperatures or lack of air movement. This is particularly mixer is recommended and mixture should be stirred until important to note when installing indoors, where all three homogeneous. Periodic mixing should take place as the job factors are often very pronounced. progresses to ensure consistent application. 9.5 Keep From Freezing 6.0 GUIDE TO APPLICATION Acrylic Resurfacer is a water-based acrylic system and it 6.1 System Recommendations must be kept from freezing during storage or in transit. If you Deco recommends one 1-2 coats of Acrylic Resurfacer prior receive product you suspect may have been exposed to to the application of any Deco Surfacing System. If using the freezing temperatures, consult your Deco Surfacing Systems Street Ice system, a minimum of two (2) coats is Representative for proper handling instructions. recommended. See Street Ice S/I-3 for further information. 10.0 LIMITED WARRANTY 6.2 Installation The Company warrants that the products to be delivered and Using a flexible rubber squeegee, apply Acrylic Resurfacer sold there under are the kind and quality described in its mix parallel to one of the sides of the surface area. Care specifications and no other warranty, except of title, is should be taken not to leave ridges where adjoining expressed or implied. All other warranties and/or liabilities, applications overlap. Under hot conditions, application is including consequential damages, are specifically excluded improved by keeping surface damp with a fine mist water whether the directions for a product’s use are followed or not. spray. Never allow water to pool on the surface. Notification of any apparent defect or defects shall be made promptly in writing to the Company. Should any product 6.3 Drying and Cure Time (unless sold as is) prove, upon our inspection, to be defective Acrylic Resurfacer must be allowed to cure a minimum of 2 in workmanship or materials in accordance with the hours before applying acrylic coatings. specifications, the Company will replace the product or refund the purchase price. No person has the authority of 7.0 COVERAGE the Company to make or accept any other warranty, liability, The undiluted coverage rate is approximately 0.06 gallons or conditions on the Company’s behalf. If the above stated per square yard, per application conditions of this warranty are unacceptable, the purchaser may return, at his expense, all unopened packages, bags or 8.0 CLEAN-UP containers for credit within 30 days from the date of All equipment can be cleaned with water if clean-up occurs purchase. immediately after application. 11.0 FOR FURTHER INFORMATION 9.0 LIMITATIONS California Products Corporation manufactures many different 9.1 Surface Limitations recreational surface products. For additional information Acrylic Resurfacer is limited to application on hot-mix asphalt contact us at: and Portland cement concrete recreational surfaces. Deco Surfacing Systems does not recommend, nor authorize the Deco Surfacing Systems application of Acrylic Resurfacer on any other surfaces a division of California Products Corporation without prior approval from your Deco Area Manager. 150 Dascomb Road Andover, MA 01810 9.2 Weather Limitations (800) 332-6178 No part of the construction involving the Deco Surfacing [email protected] System should be conducted during rainfall, or when rainfall is imminent. The air temperature must be at least 60ºF and rising. Do not apply when surface temperature is above 140ºF.

9.3 Do Not Over Dilute The maximum dilution ratio is 3:2. Over dilution will cause streaking, foaming, adhesion failure, sand fall-out and poor overall durability of the coating.

9.4 Indoor Application Drying

Acrylic Resurfacer 03/2008

DecoBase I™ 4.4 Surface Imperfections • If DecoBase I is the first step to coating a newly constructed acrylic system, the surface must be prepared with Acrylic Resurfacer first. Please refer to 920-05 the data sheet Acrylic Resurfacer 920-29. ACRYLIC TEXTURE FOR RECREATIONAL SURFACES • If DecoBase I is the first step in recoating an existing 1.0 MATERIAL DESCRIPTION acrylic system, the surface should be flooded with water DecoBase I™ 920-05 coating is a sand filled, 100% acrylic and allowed to drain prior to application of DecoBase I. latex compound designed for squeegee application to Any depressions capable of submerging a U.S. five- relatively smooth surfaces. It is supplied as a non-pigmented cent piece after one hour should be marked with chalk, concentrate to be tinted with DecoColor® MP 920-27 and not crayon or a grease pencil. These areas must then diluted with water prior to use. DecoBase I coating results in be allowed to thoroughly dry. Once dried, a patch must a dense, durable textured surface and adds firm thickness to be applied to the marked areas. For patching the color system. information, please refer to the product data sheet for Acrylic Patch Binder 920-39. 2.0 INTENDED USE DecoBase I is designed to impart the desired texture that If DecoBase I application follows the DecoTurf Cushion controls the speed of play. It fills minor surface irregularities System, do not flood the court. Proceed with Mixing and provides a tough, wear-resistant coating which imparts a Instructions. consistent texture across the playing field. 5.0 MIXING INSTRUCTIONS 3.0 PHYSICAL PROPERTIES The following mixes have been found to be satisfactory for Color: Neutral average surface conditions: Coverage Rate (undiluted): .06 gallons/square yard, DecoBase I 920-05 55 gallons .0865 gallons/square yard DecoColor ® MP 920-27 15 gallons over DecoBase II Clean Potable Water 23 gallons Weight per gallon: 12.0 lbs. Curing conditions: 70°F & 50% relative humidity After the addition of water thorough mixing is required. A Estimated cure time: 4 hours mechanical drill mixer is recommended and mixture should be stirred until homogeneous. Periodic mixing should take Minimum ambient, surface & place as the job progresses to ensure consistent application. product installation temperature: 60° and rising

Note: Low temperatures & high humidity will increase drying 6.0 GUIDE TO APPLICATION time drastically. Maximum surface temperature = 140°F. 6.1 System Recommendation Two (2) applications have proven to give excellent 4.0 SURFACE PREPARATION performance results. Deco recommends the use of Acrylic 4.1 Base Construction Resurfacer 920-29 prior to the application of any Deco Surface must meet or exceed the American Sports Builders Surfacing System. See the data sheet on Acrylic Resurfacer Association (ASBA) applicable Guidelines. Upgrading and for further information. recoating previously colored surfaces requires the surface and base construction to be in sound condition and in 6.2 Installation compliance with the applicable ASBA Guidelines. Using a flexible rubber squeegee, 50 or 70 durometer, apply DecoBase I mix parallel to one of the sides of the area to be 4.2 Substrate Cure Requirements coated. Care should be taken not to leave ridges where New hot-mix asphalt surfaces must be allowed to cure for a adjoining applications overlap. Application in hot conditions minimum of 14 days prior to application of DecoBase I. For is improved by keeping surface damp with a fine mist water new Portland cement concrete surfaces, a minimum of 28 spray. Additional applications should be installed at 90° to days cure time is required. the previous application.

4.3 Surface Condition The surface upon which DecoBase I is to be applied must be smooth, free of dirt, loose or flaking paint, oily materials or 6.3 Drying and Cure Time chemical residues, vegetation of any sort and any other DecoBase I must be allowed to dry 4 hours before another debris or foreign matter that may prevent the proper product coating can be applied, assuming 70°F temperatures and adhesion. DecoBase I 10/2005

50% relative humidity. Low temperatures and high humidity defective in workmanship or materials in accordance with the will increase drying time dramatically. specifications, the Company will replace the product or refund the purchase price. No person has the authority of 7.0 COVERAGE the Company to make or accept any other warranty, liability, The undiluted coverage rate is approximately 0.06 gallons or conditions on the Company’s behalf. If the above stated per square yard, per application (150 square feet per gallon). conditions of this warranty are unacceptable, the purchaser If applied over DecoBase II the undiluted coverage rate is may return, at his expense, all unopened packages, bags or approximately .0865 gallons per square yard, per application containers for credit within 30 days from the date of (105 square feet per gallon). purchase.

8.0 CLEAN-UP 11.0 FOR FURTHER INFORMATION If clean-up occurs immediately after application, water will California Products Corporation manufactures many different remove acrylics from equipment. recreational surfaces products. For additional information contact us at: 9.0 LIMITATIONS 9.1 Surface Limitations Deco Surfacing Systems DecoBase I is limited to application on hot-mix asphalt and a division of California Products Corporation Portland cement concrete recreational surfaces. Please see 150 Dascomb Road the DecoColor installation guideline for new and existing Andover, MA 01810 asphalt and concrete surfaces for more information. Deco (800) 332-6178 Surfacing Systems does not recommend, nor authorize the [email protected] application of DecoBase I on any other surfaces without prior approval from your Deco Area Manager.

9.2 Weather Limitations No part of the construction involving the Deco Surfacing System should be conducted during rainfall, or when rainfall is imminent. The air temperature must be at least 60ºF and rising. Do not apply when surface temperature is above 140ºF.

9.3 Do Not Over Dilute Over dilution can cause streaking, foaming, adhesion failure, sand fall-out and poor overall durability of the coating.

9.4 Indoor Application Curing Drying times are retarded by high humidity, cool temperatures or lack of air movement. This is particularly important to note when installing indoors, where all three factors are often very pronounced.

9.5 Keep From Freezing DecoBase I is a water-based acrylic system and it must be kept from freezing during storage or in transit. If you receive product you suspect may have been exposed to freezing temperatures, consult your Deco Area Manager for proper handling instructions.

10.0 LIMITED WARRANTY The Company warrants that the products to be delivered and sold there under are the kind and quality described in its specifications and no other warranty, except of title, is expressed or implied. All other warranties and/or liabilities, including consequential damages, are specifically excluded whether the directions for a product’s use are followed or not. Notification of any apparent defect or defects shall be made promptly in writing to the Company. Should any product (unless sold as is) prove, upon our inspection, to be DecoBase I 10/2005 New hot-mix asphalt surfaces must be allowed 14 days minimum cure time prior to application of Deco products.  DecoColor MP For new Portland cement concrete surfaces, a minimum of 28 days cure time is required. After 28 days, new concrete must be acid-etched with either phosphoric or muriatic acid. Application may begin thereafter. Classic 4.3 Surface Condition The surface on which DecoColor is to be applied must be 920-27 smooth, free of dirt, loose or flaking paint, oily materials or chemical residues, vegetation of any sort and any other ACRYLIC COLOR FOR RECREATIONAL SURFACES debris or foreign matter that may prevent the proper product adhesion. Thoroughly rout existing cracks of dirt, debris and 1.0 MATERIAL DESCRIPTION loose impediments. Cracks should be blown clean with an air DecoColor MP Classic 920-27 is a full bodied, high compressor. Consult the data sheet 64061 Deco Crack Filler for performance acrylic latex coating. It is fortified with specially application information. selected fillers and is pigmented in eleven standard colors. Special colors are possible upon request, however minimum 4.4 Surface Imperfections quantities do apply. DecoColor MP Classic offers the Before application of primers or Acrylic Resurfacer, the court advantage of using one product for the texture courses and surface shall be flooded with water and allowed to drain. the finish course. Any depressions capable of submerging a U.S. five-cent piece after one hour should be marked with chalk, not crayon 2.0 INTENDED USE or a grease pencil. These areas must be allowed to DecoColor MP Classic is intended for use as a texture thoroughly dry. Once dried, a patch must be applied to the and/or top coat for recreational surfaces. Job mixing gives marked area. For patching products and mix designs, the installer the flexibility to meet individual job conditions. please refer to the product data sheet for Acrylic Patch The finish texture and speed of play can be modified through Binder 920-39. the size and amount of sand used in the mix. This product allows the contractor the flexibility to select and add the 4.5 Priming proper sand to meet specific job requirements. Priming of asphalt surfaces is only necessary if existing asphalt is too badly weathered to establish a strong bond 3.0 PHYSICAL PROPERTIES with the Acrylic Resurfacer. In the case of extremely oxidized Classic Colors: US Open Blue, Spring Green, asphalt surfaces, contact your Deco Area Manager. Winter Green, Forest Green, Summer Red, Royal Blue, When applying Acrylic Resurfacer to new concrete surfaces, America’s Red Clay, a primer is necessary to improve adhesion. Deco Surfacing Tour Purple, Adobe Tan, Systems offers California Ti-Coat 63903 & 63904, a two- package water based epoxy primer. Consult the respective Olympic Blue, & Stone Gray data sheets for proper application. Weight per gallon: 10.5 lbs.

Curing conditions: 70° F & 50% relative humidity If the concrete surface has been previously coated with To top coat: 4 hours acrylic material, no priming is necessary. Estimated curing time: 24 hour minimum Minimum ambient, surface & 5.0 MIXING INSTRUCTIONS product installation temperature: 60°F and rising The following mixes have been found to be satisfactory for Note: Low temperatures or high humidity will increase drying average surface conditions: time drastically. Maximum surface temperature = 140° F. 5.1 Texture Course 4.0 SURFACE PREPARATION DecoColor MP Classic 920-27 55 gal 30 gal 4.1 Base Construction Clean potable water 27 gal 15 gal Surface must meet or exceed the American Sport Builders Silica Sand (60-90 mesh) 440 lb 240 lb Association (ASBA) applicable Guidelines. Upgrading and NOTE: For a slower ball bounce and rougher texture, one or recoating previously colored surfaces requires the surface more texture courses may be installed in place of the finish and base construction to be in sound condition and in course. compliance with the applicable ASBA Guidelines.

5.2 Finish Course 4.2 Substrate Cure Requirements DecoColor MP Classic 920-27 55 gal 30 gal DecoColor MP Classic 10/2005 Clean potable water 38 gal 20 gal 9.0 LIMITATIONS NOTE: For a slower ball bounce and rougher texture, one or 9.1 Surface Limitations more texture courses may be installed in place of the finish DecoColor MP is limited to application on hot-mix asphalt course. and Portland cement concrete recreational surfaces. Please see Deco installations guidelines fro new and existing 5.3 Mixing asphalt and concrete surfaces for more information. Deco Do not use sand containing clay, silt, ferrous metals or Surfacing Systems does not recommend, nor authorize the salt. The outcome of the texture course depends heavily on application of DecoColor MP on any other surfaces without what type of sand you chose. Deco’s specifications are prior approval from your Deco Area Manager. based on 60-90 mesh sand. Please submit your sand samples to the California Products Research and 9.2 Weather Limitations Development laboratory for analysis and approval before No part of the construction involving the Deco Surfacing mixing with DecoColor MP Classic. Sand should be slowly System should be conducted during rainfall, or when rainfall added to undiluted MP followed by the addition of water. A is imminent. The air temperature must be at least 60ºF and mechanical mixer is recommended and mixture should be rising. Do not apply when surface temperature is above stirred until homogeneous. Periodic mixing should take place 140ºF. as the job progresses to ensure consistent application. 9.3 Do Not Over Dilute 6.0 GUIDE TO APPLICATION The maximum dilution ratio for the Texture Course is two (2) 6.1 System Recommendation parts DecoColor to one (1) part water. The maximum Two (2) texture course applications and one (1) finish course dilution ratio for the Finish Course is three (3) parts has proven to give excellent performance results. Deco DecoColor to two (2) parts water. Over dilution will cause recommends the use of Acrylic Resurfacer 920-29 prior to streaking, foaming, adhesion failure, sand fall-out and poor the application of DecoColor. See the data sheet on Acrylic overall durability of the coating. Resurfacer for more information. 9.4 Indoor Application Drying 6.2 Installation Drying times are retarded by high humidity, cool Using a flexible rubber squeegee, 50 or 70 durometer, apply temperatures or lack of air movement. This is particularly DecoColor MP Mix parallel to one of the sides of the area to important to note when installing indoors, where all three be coated. Care should be taken not to leave ridges where factors are often very pronounced. adjoining applications overlap. Applications in hot conditions are improved by keeping surface damp with a fine mist water 9.5 Keep From Freezing spray. No pooling should be allowed. Additional DecoColor MP 920-27 is a water-based acrylic system and it applications should be installed at 90° to the previous must be kept from freezing during storage or in transit. If you application. receive product you suspect may have been exposed to freezing temperatures, consult your Deco Surfacing Systems 6.3 Drying and Cure Time Representative for proper handling instructions. DecoColor MP must be allowed to dry for 4 hours between coating applications. Completed projects should be allowed 10.0 LIMITED WARRANTY 24 hours before releasing to play. The Company warrants that the products to be delivered and sold there under are the kind and quality described in its specifications 7.0 COVERAGE and no other warranty, except of title, is expressed or implied. All other warranties and/or liabilities, including consequential damages, 7.1 Texture Course are specifically excluded whether the directions for a product’s use The undiluted coverage rate is approximately 0.05 gallons are followed or not. Notification of any apparent defect or defects per square yard, per application (180 square feet per gallon). shall be made promptly in writing to the Company. Should any product (unless sold as is) prove, upon our inspection, to be 7.2 Finish Course defective in workmanship or materials in accordance with the The undiluted coverage rate is approximately 0.04 gallons specifications, the Company will replace the product or refund the per square yard, per application (225 square feet per gallon). purchase price. No person has the authority of the Company to make or accept any other warranty, liability, or conditions on the 8.0 CLEAN-UP Company’s behalf. If the above stated conditions of this warranty All equipment can be cleaned with water if clean-up occurs are unacceptable, the purchaser may return, at his expense, all immediately after application. unopened packages, bags or containers for credit within 30 days from the date of purchase.

11.0 FOR FURTHER INFORMATION

California Products manufactures many different recreational

surfaces products. For additional information contact us at:

DecoColor MP Classic 10/2005

Deco Surfacing Systems a division of California Products Corporation 150 Dascomb Road Andover, MA 01810 (800) 332-6178 [email protected]

DecoColor MP Classic 10/2005

Hi-Hide Line 5.0 MIXING INSTRUCTIONS Hi-Hide Line Paint comes ready to apply. Only gentle stirring is necessary. DO NOT DILUTE.

Paint 920-22 6.0 GUIDE TO APPLICATION 6.1 System Recommendations One or two (1-2) applications has proven to give excellent 6020 coverage.

TEXTURED OR NON-TEXTURED 6.2 Application Apply Hi-Hide Line Paint to the clean, dry, color coated XTERIOR NTERIOR INE ARKING AINT OR E /I L M P F surface by brush, roller, airless spray or special marking ATHLETIC SURFACES equipment. Apply tape to both sides of the area to be striped. Apply a primer coat of ClearGlo or the final acrylic 1.0 MATERIAL DESCRIPTION color coating over the inside edges of the tape. This will seal A highly reflective 100% acrylic marking paint for use over the tape to the acrylic surface and prevent the Hi-Hide Line any bituminous surface, or acrylic color coating system in Paint from bleeding under the tape. recreational or light traffic areas. Hi-Hide Line Paint will not cause cracking, crazing, peeling, or deterioration to asphalt 6.3 Drying and Cure Time that is typical of solvent-type traffic paints. Hi-Hide Line Paint must be allowed to dry for 4 hours between coating applications. Completed projects should be 2.0 INTENDED USE allowed 24 hours before releasing to play. For the striping of color-coated recreational surfaces or any asphalt or concrete surface in light traffic areas, such as 7.0 COVERAGE Tennis Courts, Play Areas, Curbs and Berms, Running Approximately one gallon of Hi-Hide Line Paint is required Tracks, & Parking Lots per standard U.S.T.A. sanctioned tennis court per application. 3.0 PHYSICAL PROPERTIES Color: White, Yellow, Red, Blue, 8.0 CLEAN-UP Green, Orange, & Black All equipment can be cleaned with water if clean-up occurs Weight per gallon: 11.0 lbs. immediately after application. Curing conditions: 70° F & 50% relative humidity 9.0 LIMITATIONS To top-coat: 4 hours 9.1 Surface Limitations Estimated cure time: 24 hours Hi-Hide Line Paint is limited to application on hot-mix asphalt Minimum ambient, surface & and Portland cement concrete recreational surfaces. Not for product installation temperature: 60° and rising application on general use roadways subjected to skidding Note: Low temperatures or high humidity will increase drying tires, snowplows, or chains. time drastically. Maximum surface temperature = 140° F. 9.2 Weather Limitations 4.0 SURFACE PREPARATION No part of the construction involving the Deco Surfacing 4.1 Substrate Cure Requirements System should be conducted during rainfall, or when rainfall New hot-mix asphalt surfaces must be allowed 14 days is imminent. The air temperature must be at least 60ºF and minimum cure time prior to application of Hi-Hide Line Paint. rising. Do not apply when surface temperature is above For new Portland cement concrete surfaces, a minimum of 140ºF. 28 days cure time is required. 9.3 Do Not Dilute 4.2 Surface Condition The surface upon which Hi-Hide Line Paint is to be applied 9.4 Indoor Application Curing must be smooth, free of dirt, loose or flaking paint, oily Drying times are retarded by high humidity, cool materials or chemical residues, vegetation of any sort and temperatures or lack of air movement. This is particularly any other debris or foreign matter that may prevent the important to note when installing indoors, where all three proper product adhesion. factors are often very pronounced.

Hi-Hide Line Paint 03/2008

9.5 Keep From Freezing Hi-Hide Line Paint is a water-based acrylic and it must be kept from freezing during storage or in transit. If you receive product you suspect may have been exposed to freezing temperatures, consult your Deco Area Manager for proper handing instructions.

10.0 LIMITED WARRANTY The Company warrants that the products to be delivered and sold there under are the kind and quality described in its specifications and no other warranty, except of title, is expressed or implied. All other warranties and/or liabilities, including consequential damages, are specifically excluded whether the directions for a product’s use are followed or not. Notification of any apparent defect or defects shall be made promptly in writing to the Company. Should any product (unless sold as is) prove, upon our inspection, to be defective in workmanship or materials in accordance with the specifications, the Company will replace the product or refund the purchase price. No person has the authority of the Company to make or accept any other warranty, liability, or conditions on the Company’s behalf. If the above stated conditions of this warranty are unacceptable, the purchaser may return, at his expense, all unopened packages, bags or containers for credit within 30 days from the date of purchase.

11.0 FOR FURTHER INFORMATION California Products Corporation manufactures many different recreational surfaces products. For additional information contact us at:

Deco Surfacing Systems a division of California Products Corporation 150 Dascomb Road Andover, MA 01810 (800) 332-6178 [email protected]

Hi-Hide Line Paint 03/2008

PRODUCT NO. 9700 TECHNICAL DATA

SOFT POLYESTER FABRIC UNTREATED

DESCRIPTION: APPLICATION: Ø A unique, 100% warp knit polyester fabric. Ø Apply a film of the cold (liquid) applied bitumen adhe- Ø Excellent tensile strength provides tear and puncture sive to the surface, in accordance with the manufac- resistance. turer’s recommendations. Ø Compatible cold (liquid) applied bitumen systems Ø Embed Fortress Soft Polyester Fabric into the adhe- and water-based elastomeric coatings. sive using a brush or broom and enough pressure to Ø Outstanding conformability and elongation proper- force the adhesive through the mesh openings and ties. around the fabric strands. Ø Superior wetting properties, lightweight and dimen- Ø Conform the fabric uniformly to the surface, avoiding sionally stable. over-stretching, bridging or “fishmouths”. Ø Will not rot, mold or mildew. Ø Apply a final coat of the cold (liquid) applied bitumen adhesive to the surface, in accordance with the manufacturer’s recommendations, ensuring that no fabric weave is visible.

Property Result

Weight, oz./sq. yd. 2.7

Tensile Strength, lb./in. 75

Tear Strength, lb./in. 13.5

Elongation to break, % 42.9

Color white

PACKAGING: Ø Available in 300 feet lengths and 42 inch cut widths. Other cut widths also available. Consult price sheet for ad- ditional details.

SPECIFICATION COMPLIANCES: Ø Meets normal industry standards

SAFETY AND ENVIRONMENTAL PRECAUTIONS: Ø CONSULT MATERIAL DATA SAFETY SHEET FOR DETAILED HANDLING AND DISPOSAL

The Brewer Company PH: (800) 394-0086 or (440) 944-3800 FX: (440) 944-1492 30060 Lakeland Blvd., Wickliffe, OH 44092-1745 Rev. 11/02 Copyright Ó 2002 The Brewer Introducing the Another Quality Product from E-Z REEL and TENNIS POST Proud USA Manufacturer Thanks to Douglas, one of America’s most popular tennis post styles just got better. When it comes to this style of post, now you don’t have to compromise on quality, looks or performance for your customers–in order to get a great price! It’s an E-Z Choice!

The new E-Z TENNIS POST from Douglas® offers you:

Better Quality - These posts use Douglas® quality materials and craftsmanship helping ensure your customers will be happier longer--reducing call-backs for you. Better Looks - Douglas’ sleek top cap design, smooth post texture, and premium powder coat fi nish creates a sharper look for your customers—and gives you another tennis post you can be proud to recommend and install. Better Performance - Enhanced E-Z REEL components increase the strength and stability of the reel mechanism. When combined with the smooth action of the high-end top cap, the E-Z TENNIS POST delivers a more solid and consistent quick-winding and quick-release performance than you would expect with this style of post.

Features:

• 2-7/8” o.d. round, steel post with 3/16” wall thickness • Includes external wind E-Z Reel for smooth, easy operation • Removable handle • Die-cast zinc top caps • Available in Green or Black • Baked-on polyester powder coat post fi nish • Can be used with optional GS-24 RD PVC E-Z Reel 2-7/8” o.d. ground sleeves

Green (Item# 63020) Black (Item# 63031)

Green (Item# 33440) Black (Item# 33440B)

The most heavy-duty vinyl windscreen. DouraScreen is resistant to water, salt, mildew and UV rays. Available in dark green or black, this fl exible foamed material also featuring DouraScreen creates a superior surface for applying custom lettering and logos. Specifi cations Features: Fabric 22% High Tenacity Polyester • Available in 6’ and 9’ heights 78% Flexible Foamed PVC • Center tabs and center reinforcement tape Open - 9 x 8 weave is standard on 9’ heights Closed - 12 x 14 weave Windbreak Open - 80 % • Custom panel lengths and heights are Closed - 95 % available Weight Open - 10 oz • Optional airvents Closed - 12 oz Tensile Strength Open - 170 x 155 Closed - 230 x 240 All materials in-stock Colors Dark Green or Black 10-14 Working day lead time Warranty 3-Year Limited

800-553-8907 - www.douglas-sports.com 090808 DOUGLAS® TENNIS NETS AND ACCESSORIES

All Douglas® Tennis Nets meet USTA requirements for official size (42’ x 3’6”). Netting is 1-3/4” square to the elements. All headbands have been lock-sewn with four rows of #32 white polyester thread. The mesh braided solid core polyethylene, unsurpassed for durability and weather resistance. Vinyl bottom side and bottom tapes are double lock-stitched with black polyester thread. All Tennis Nets include 1/2” tape and side pockets of headbands are polyester based and won’t shrink, mildew or rot when exposed Fiberglass side dowels.

TN-45 TN-36T TN-30DH

TN-28DM TN-36DMT TN-30DM

Headband Netting Top 6 Rows Double Item # Net Material Weight Size Break Strength Warranty Mesh

Professional Nets USA Manufactured by Douglas®

20045 TN-45 Double thick 100% polyester 48 oz 3.5 mm 325 lb. No 5 Year Warranty 20040 TN-40 (not pictured) Vinyl Coated Polyester, 2-ply 65 oz. (20 oz./sq. yd.) 3.5 mm 325 lb. No 5 Year Warranty Championship Nets 30036T TN-36 -tapered Vinyl Coated Polyester, 2-ply 65 oz. (20 oz./sq. yd.) 3.5 mm 325 lb. No 5 Year Warranty 30038TD TN-36DMT -tapered Vinyl Coated Polyester, 2-ply 65 oz. (20 oz./sq. yd.) 3.5 mm 325 lb. Yes 5 Year Warranty Tournament Nets 30029 TN-30 Vinyl Coated Polyester 32 oz./sq. yd. 3.0 mm 285 lb. No 4 Year Warranty 30030 TN-30DM -tapered Vinyl Coated Polyester, 2-ply 65 oz. (20 oz./sq. yd.) 3.0 mm 285 lb. Yes 4 Year Warranty 30060 TN-28DM Durable Polyester Web N/A 3.0 mm 285 lb. Yes 4 Year Warranty

Bottom Taper (Item # 20062) Specialty Nets Singles Tennis Nets: 3’6” x 33’ All tennis nets can be bottom fit by tapering the 42” end to 36” at center. This reduces the Features vinyl coated polyester Paddle Tennis Nets: 32” x 21’10” amount the net rubs on the court surface prolonging the life of the net. headband with a 3.0 polyethylene Platform Tennis Nets: 3’ x 23’ netting. 4 Year Warranty. QuickStart Tennis Nets: 3’ x 21’9” Pickleball Tennis Nets: 3’ x 21’9” Adjustable Center Straps All straps are made from heavy-duty 2” polyester white web, nickel plated web slides and snaps.

Procam (Item # 20625) 2” cam buckle, with swivel loop bolt snap

Velcro (Item # 30602) Velcro adjustment, with swivel loop bolt snap

Classic (Item # 30603) Non-slip reverse web slide with double ended snap

Basic (Item # 30600) Non-slip reverse web slide with swivel loop bolt clip

Deluxe (Item # 20600) Non-slip reverse web slide with swivel loop bolt snap

Center Pipe Anchor Replacement Snaps (Item # 63428) Loop Snap (Item # 10601) 1.9” OD Galvanized Steel 2” replacement loop snap

Double Snap (Item # 10604) Dowels Double ended bolt replacement snap Dowel FRP (Item # 15110) 1/2” Fiberglass

Dowel Wood (Item # 10318) Lacing Cord 5/8” Hardwood TNLC (Item # 10338) Tennis net lacing cord; 2 pieces of 4 mm white polyester braided cord 4’ long and 2 pieces 3 mm braided polyethylene 15’ long.

Cord 3mm (Item # 10337) 500’ spool of 3 mm braided polyethylene Replacement Headband (HB-42) (Item # 30042) Heavy-duty polyester web lacing eyelets on 6” centers, includes lacing cord.

Singles Stick (Item # 34753) Deluxe all aluminum with cap and foot Replacement Cable (RVC-47) (Item # 20647) 47’ galvanized steel cable. 5/32” vinyl coated to 1/4” looped each end.

800-553-8907 - www.douglas-sports.com COURTSIDE ACCESSORIES

Score Keeper Courtside Coolers and Accessories (Item # 34754) A functional and attractive courtside alternative • Clamps easily to any size post to water fountains • Steel construction Redwood Cooler Stand • Swivel base for rotation (Item # 34910) • 4” x 7” game numbers are HD Attractive, durable redwood durable plastic construction • Card numbers are 1 thru 7 • Includes 2 Sets of game Universal Cooler Stand numbers, 2 sets of “sets won” (Item # 34911B) and a name plate with a pen Premium long lasting metal construction with a black Court Caddy baked enamel fi nish Green (Item # 34745) Black (Item # 34744) *Coolers and accessories • Fits on most tennis posts are sold separately • Combination tray/cup holder and removable trash basket • Available in dark green Cooler White/Blue or black Court Caddy Basket Green (Item # 34746) (Item # 34901) Score Post Black (Item # 34746B) Ready to serve ice water or beverages Pro-Set (Item # 34732) Name Cards (Item # 34733) Receptacle for beverage cups • Use tennis balls to score matches! and other court trash Cooler Green (Item # 34900) • Lightweight insulated cooler • Both games and sets won are displayed (Item # 34903) Cup Dispenser • All green in color with a • Tennis balls mark the score in green and white pockets. • Convenient sanitary cup dispenser • Flat lid without a handle • Results are highly visible • Portable, attaches to cooler • On changeover, unit is rotated and stops at 180 degrees • Uses vertical space above net post Water Cooler Carrier • All metal support made of high strength aluminum will not rust Small (Item # 34915) • Name cards mount on top of mast Large (Item # 34916) • All parts are durable and replaceable • Constructed of the highest grade ultra- violet rated Poly Vinyl Chloride • Completely weather resistant; will not Court Signs “yellow” from sun exposure Court Rules (Item # 34872) • Wheels with swivel casters for use on any Soft Sole Shoes Only (Item # 34872A) hard surface Courts Closed for Maintenance (Item # 34872B) • Virtually indestructible Please Register (Item # 34872C) • Includes cup dispenser and wastebasket Please Keep Gates Closed (Item #34872D) • Cooler not included • Heavy-duty durable plastic • Green background with white printing • Pre-drilled mounting holes

See Page 7 for Vinyl Court Signs

Fence Cabana (Item # 33854) Cabana Bench • Fence-mounted awning gable design 8’ Model (Item # 30019) 8’L x 6’ W x 8’10” H The Outpost measuring 4’ W x 10’ L x 2’6” H 10’ Model (Item # 33871) 10’L x 6’ W x 8’10”H 29-1/2” W x 49-1/2” H x 7-3/4” D (Item # 33870) 37-1/2” W x 49-1/2” H x 7-3/4” D (Item # 33871) • Framing constructed of Galvanized posts and • Direct bury or surface mount installation • Maintenance free outdoor message display board powder coated steel • 3” x 3” Black powder-coated, heavy gauge steel frame • Superior weather resistant vinyl exterior • Bolts securely to fence top rail with U-brackets • Standard durawood plastic slats • Sliding Plexiglas doors on aluminum tracks • All-weather, fade resistant Sunbrella canvas • Canopy is available in Forest Green, Kelly Green, • Option of post or fence mounting (not included) with fi ve year fade warranty Burgundy, Pacifi c Blue or Brown • Two standard colors available: forest green • Available with white stripes or solid with white border and white striped or solid forest green Contact us for Additional Information Aluminum Umpire Chair Classic Umpire Chair Judges PVC Umpire Chair (Item # 34757) Green (Item # 34777) (Item # 34773) Optional Canopy (Item # 34773C) • High-quality aluminum construction offers Black (Item # 34778) • Super Strong, manufactured with highest grade, durability and safety • Custom fabricated powder coated steel ultra-violet rated Poly Vinyl Chloride available. • Lightweight for easy portability construction • Will not deteriorate or yellow • Will not rust or rot like other umpire chairs • Heavy duty construction made to last a lifetime • Comes with a high-grade cushion with superior • Sized to pass through typical doors and gates • Extra comfortable seat cushions are removable fabric and 3-1/2” thick foam • Comfortable red plastic seat ships in separate for out-of-weather storage • Available in 6’2” or USTA required 7’2” height carton • Convenient top & bottom wooden storage tables • Detachable canopies are also available • Wheels will not scuff court surfacing • Canopies are made with Sunbrella canvas fabric • Optional umbrella available that will last for many years • Rolls easily with or without canopy

Courtsider Bench 5’ White (Item # 34760) 5’ Forest Green (Item # 34761) • Constructed of maintenance free extruded high density polyurethane • Weatherproof and lightweight • Durable solid plastic legs can be bolted to solid surfaces for permanent positioning • Ships knocked down in four easy-to- assemble components Rain/Shine Bench 5’3” long (Item # 33862) Deluxe Courtsider 7’8” long (Item # 33863) 5’ White (Item # 34764) • Extruded white vinyl holds up to harsh 5’ Forest Green (Item # 34765) weather conditions 6’6” White (Item # 34762) • 17” seat depth and 16” high backrest 6’6” Forest Green (Item # 34763) • Large feet disperse weight over more area • Same long lasting construction as the standard Courtsider bench • Deluxe model has more slats for even greater stability and is contoured for comfort

Durawood Dent-Saver Bench 4’ long (Item# 33858) 5’ long (Item # 33859) 6’ long (Item # 33860) • Recycled HDPE plastic • Resistant to rusting, rotting, warping Players Pro Bench and splitting 5’ (Item # 34767) • 17” H, 18-1/2” D, and 4’, 5’ or 6’L • Constructed of PVC to hold up against • Available in forest green, gray or cedar weather and player abuse • Available in white only

800-553-8907 - www.douglas-sports.com