Kdc-Bt648u Kdc-X695 Kdc-X395 Kdc-348U
Total Page:16
File Type:pdf, Size:1020Kb
KDC-BT648U KDC-X695 KDC-X395 KDC-348U CD-RECEIVER INSTRUCTION MANUAL AMPLI-TUNER LECTEUR DE CD MODE D’EMPLOI REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM MANUAL DE INSTRUCCIONES Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver. For your records Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-BT648U/ KDC-X695/ KDC-X395/ KDC-348U Serial number US Residents Only Register Online Register your Kenwood product at www.Kenwoodusa.com © 2010 Kenwood Corporation All Rights Reserved. B64-4798-10/01 (KW/K0) BB64-4798-10_01_K.indb64-4798-10_01_K.indb 1 111/01/061/01/06 115:065:06 CONTENTS Safety 3 Operation of Hands-Free Phoning 15 Maintenance Getting Started Making a Call Preparation 4 Receiving a Call How to attach/detach the faceplate During a Call How to reset your unit Call Waiting How to prepare the remote controller Downloading the Phone Book (RC-405) Bluetooth Setup 18 Getting Started 5 Easy Pairing function Canceling the display demonstration Registering Bluetooth Device (Pairing) Setting the demonstration mode Selecting the Bluetooth Device Adjusting the clock Setting a Voice Command Initial settings before operations Bluetooth Setup Basic Operations 6 SMS (Short Message Service) 23 Muting upon the reception of a phone call Downloading the SMS Listening to the Radio 8 Display the SMS Adjust [SETTINGS] mode settings HD Radio™ Tuner Control 24 Listening to the other external Direct Access Tuning using the remote components 9 controller (RC-405) iTunes Tagging Listening to a Disc/ Adjust [SETTINGS] mode settings USB device/ iPod 10 Satellite Radio Tuner Control 26 Start playing a disc Category and Channel Search Start playing a USB device or iPod Channel Scan Removing the USB device or iPod Direct Access Tuning using the remote Start playing the disc changer controller (RC-405) Selecting Repeat Play Adjust [SETTINGS] mode settings Selecting Random Play All Random Play Function settings 28 Selecting Magazine Random Play Selecting Scan Play Installation/connection 30 Selecting a folder/track/file Troubleshooting 34 Alphabet Search for iPod Direct Music Search using the remote Specifications 37 controller (RC-405) Direct Disc Search using the remote controller (RC-405) My Playlist for iPod iPod control by Hand mode Adjust [SETTINGS] mode settings 2 English BB64-4798-10_01_K.indb64-4798-10_01_K.indb 2 111/01/061/01/06 115:065:06 Safety WARNING Stop the car before operating the unit. Important to know... ■ To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. ■ Caution: Adjust the volume so that you can hear sounds outside the car. Driving with the volume too high may cause an accident. ■ Condensation: When the car is air- conditioned, moisture may collect on the laser lens. This may cause disc read errors. In ■ The “AAC” logo is a trademark of Dolby this case, remove the disc and wait for the Laboratories. moisture to evaporate. ■ The Bluetooth word mark and logos ■ The illustrations in this manual are examples are owned by the Bluetooth SIG, Inc. used to explain more clearly how the and any use of such marks by Kenwood controls are used. Therefore, what appears Corporation is under license. Other on the illustrations may differ from what trademarks and trade names are those of appears on the actual equipment. their respective owners. ■ If you experience problems during ■ Ready to receive HD Radio™ broadcasts installation, consult your Kenwood dealer. when connected to the KTC-HR300/ KTC- ■ When you purchase external components, HR200/ KTC-HR100TR, sold separately. check with your Kenwood dealer to make ■ “Made for iPod” and “Made for iPhone” sure that they work with your model and in mean that an electronic accessory has your area. been designed to connect specifically to iPod or iPhone, respectively, and has Maintenance been certified by the developer to meet Cleaning the unit: Wipe off the dirt on the Apple performance standards. Apple is panel with a dry silicon or soft cloth. Failure not responsible for the operation of this to observe this precaution may result in device or its compliance with safety and damage to the monitor or unit. regulatory standards. Please note that the Cleaning the connector: Wipe off dirt on use of this accessory with iPod or iPhone the connector of the unit and faceplate. Use may affect wireless performance. ■ a cotton swab or cloth. iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. ■ iTunes is a trademark of Apple Inc. This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful influence on the environment. English 3 BB64-4798-10_01_K.indb64-4798-10_01_K.indb 3 111/01/061/01/06 115:065:06 Preparation How to attach/detach the faceplate How to prepare the remote controller (RC-405) When you use the remote controller for the 1 1 first time, pull out the insulation sheet. 2 Insulation sheet 2 ■ Do not expose the faceplate to direct sunlight, excessive heat, or humidity. Also avoid places with too much dust or the If the effectiveness of the remote possibility of water splashing. controller decreases, replace the battery. ■ Keep the faceplate in its casing while detached. 2 4 ■ The faceplate is a precision piece of equipment and can be damaged by shocks 3 or jolts. ■ To prevent deterioration, do not touch the 1 terminals of the unit and faceplate with your fingers. ¤ Caution: How to reset your unit ■ Do not set the remote control in hot places such as on the dashboard. If this unit fails to operate ■ Lithium battery. properly, press the reset 1 Danger of explosion if the battery is button. incorrectly replaced. Replace only with the The unit returns to factory 2 same or equivalent type. settings when the reset ■ The battery pack or batteries shall not be button is pressed. exposed to excessive heat such sunshine, 3 fire or the like. ■ Keep battery out of reach of children and in Reset button original package until ready to use. Dispose of used batteries promptly. If swallowed contact physician immediately. CALIFORNIA, USA ONLY This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/ perchlorate 4 English BB64-4798-10_01_K.indb64-4798-10_01_K.indb 4 111/01/061/01/06 115:065:06 Getting Started Canceling the display Adjusting the clock demonstration 1 Press the volume knob to enter The display demonstration is always turned [FUNCTION] mode. on unless you cancel it. 2 Turn the volume knob to select [SETTINGS], then press to enter. When you turn on the power (or after you 3 Turn the volume knob to select [CLOCK], reset the unit), the display shows: then press to enter. [CANCEL DEMO] \ [PRESS] \ [VOLUME 4 Turn the volume knob to select [CLOCK KNOB] ADJUST], then press to enter. 1 Press the volume knob. Clock hour flashes on the display. [YES] is selected as the initial setup. 5 Turn the volume knob to adjust the hour, 2 Press the volume knob again to confirm. then press to enter minute adjustment. [DEMO OFF] appears. Clock minutes flashes on the display. ■ If no operation is done for about 15 seconds 6 Turn the volume knob to adjust the or if you turn the volume knob to select minute, then press to confirm. [NO] in step 2, [DEMO MODE] appears and Press 4 / ¢ to move between the the display demonstration starts. hour and minute adjustment. 7 Hold to finish the procedure. Setting the demonstration mode 1 Press the volume knob to enter Initial settings before operations [FUNCTION]. 1 Press SRC to enter [STANDBY] mode. 2 Turn the volume knob to select [DEMO 2 Press the volume knob to enter MODE], then press to enter. [FUNCTION] mode. 3 Turn the volume knob to select [ON] or 3 Turn the volume knob to select [INITIAL [OFF]. SET], then press to enter. If [ON] is selected, display demonstration 4 Turn the volume knob to make a starts if no operation is done for about 20 selection, then press to confirm. seconds. See table below for selection. 4 Hold to finish the procedure. 5 Hold to finish the procedure. Item Selectable setting (Preset: *) PRESET TYPE NORMAL *: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM). ; MIX: Memorizes one station for each preset button regardless of the selected band (FM1/ FM2/ FM3/ AM) and another Satellite Radio Tuner. KEY BEEP ON */ OFF: Activates/deactivates the keypress tone. BUILT-IN AUX ON1 *: Outputs sound of the connected external component through the car speakers when “AUX” is selected as the source. ; ON2: Outputs sound from the connected external component when “AUX” is selected as the source. When you turn on the power, the sound attenuates (to prevent noise when no external component is connected). Turn the volume knob clockwise to return to the previous volume level. ; OFF: Disables “AUX” in source selection. CD READ 1*: Automatically distinguishes between audio file disc and music CD. ; 2: Forces to play as a music CD. No sound can be heard if an audio file disc is played. SP SELECT OFF */ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance. F/W UP xx.xx YES: Starts upgrading the firmware.