INTAKE and EXHAUST MANIFOLD GASKETS Intake and Exhaust Manifolds

Home , Exhaust manifold

CLEAN ALL THREADS by using a wire brush for bolts and studs, tap all bolt holes and stud nuts. Apply a high temperature anti-seize lubricant to the bolt and stud threads.

REASSEMBLE MANIFOLDS. Install the intake-to-exhaust gasket between the INTAKE AND EXHAUST MANIFOLD GASKETS intake and exhaust manifolds. Only finger tighten the manifolds together. Upon disassembly, it is likely to find the absence of an exhaust manifold gasket ATTACH AND ALIGN GASKET(S) TO CYLINDER HEAD(S). If gasket is steel since none was offered as original equipment. However, this set includes an ex- faced on one side and fiber faced on the other, install steel faced side toward the haust manifold gasket to accomodate slight casting distortion or corrosion that manifold. may have occured over the engine’s service life. Therefore, we recommend that the included exhaust manifold gasket be installed by the following instructions. ATTACH AND ALIGN fiber intake manifold gasket over the intake/exhaust gasket. REMOVE MANIFOLDS from cylinder heads. IMPORTANT: You must disassemble the intake manifold from the exhaust manifold to allow for corrected realignment REINSTALL INTAKE AND EXHAUST MANIFOLD ASSEMBLY to cylinder heads. of the manifolds to the cylinder head during the reassembly. Torque securely to OEM specifications.

CLEAN MATING SURFACES of all foreign material including old gaskets, sealer Now torque the intake manifold exhaust connection to OEM specifications. Over- and oil. You may wish to use a degreaser. torquing can fracture the manifold or cause the bolts and studs to break. © 2007 Federal Mogul Incorporated Printed in U.S.A. -continued- Form No. I-1362 (Rev. 02/93)

CLEAN ALL THREADS by using a wire brush for bolts and studs, tap all bolt holes and stud nuts. Apply a high temperature anti-seize lubricant to the bolt and stud threads.

REASSEMBLE MANIFOLDS. Install the intake-to-exhaust gasket between the intake and exhaust manifolds. Only finger tighten the manifolds together. INTAKE AND EXHAUST MANIFOLD GASKETS ATTACH AND ALIGN GASKET(S) TO CYLINDER HEAD(S). If gasket is steel Upon disassembly, it is likely to find the absence of an exhaust manifold gasket faced on one side and fiber faced on the other, install steel faced side toward the since none was offered as original equipment. However, this set includes an ex- manifold. haust manifold gasket to accomodate slight casting distortion or corrosion that may have occured over the engine’s service life. Therefore, we recommend that ATTACH AND ALIGN fiber intake manifold gasket over the intake/exhaust gas- the included exhaust manifold gasket be installed by the following instructions. ket. REMOVE MANIFOLDS from cylinder heads. IMPORTANT: You must disassemble REINSTALL INTAKE AND EXHAUST MANIFOLD ASSEMBLY to cylinder heads. the intake manifold from the exhaust manifold to allow for corrected realignment Torque securely to OEM specifications. of the manifolds to the cylinder head during the reassembly.

CLEAN ALL THREADS by using a wire brush for bolts and studs, tap all bolt holes and stud nuts. Apply a high temperature anti-seize lubricant to the bolt and stud threads.

Now torque the intake manifold exhaust connection to OEM specifications. Over- CLEAN MATING SURFACES of all foreign material including old gaskets, sealer torquing can fracture the manifold or cause the bolts and studs to break. and oil. You may wish to use a degreaser. © 2007 Federal Mogul Incorporated Printed in U.S.A. Form No. I-1362 (Rev. 02/93) -continued- CLEAN ALL THREADS by using a wire brush for bolts and studs, tap all bolt holes and stud nuts. Apply a high temperature anti-seize lubricant to the bolt and stud threads.

CLEAN ALL THREADS by using a wire brush for bolts and studs, tap all bolt holes and stud nuts. Apply a high temperature anti-seize lubricant to the bolt and stud threads.