Automotive Service Modern Auto Tech Study Guide Chapter 67 & 69 Pages 1280 ­ 1346 Suspension & Steering 32 Points Automotive Service 1

Total Page:16

File Type:pdf, Size:1020Kb

Automotive Service Modern Auto Tech Study Guide Chapter 67 & 69 Pages 1280 ­ 1346 Suspension & Steering 32 Points Automotive Service 1 Automotive Service Modern Auto Tech Study Guide Chapter 67 & 69 Pages 1280 ­ 1346 Suspension & Steering 32 Points Automotive Service 1. The ____________________ system allows a vehicle’s tires & wheels to move up and down as they roll. Steering Suspension Brake Automotive Service 2. Suspension can be grouped into 2 broad categories: _________________ & ________________. Independent & Non­independent Coil Springs & Air Springs Active & Passive Automotive Service 3. The perfect suspension system balances understeer and oversteer, resulting in ______________ steering. Tight Neutral Loose Automotive Service 4. Compressing springs is known as ________. As springs extend, they are said to ________. Jounce, Rebound Bounce, Resound Dribble, Rebound Automotive Service 5. Springs can be one of 4 types: A. _________, B. __________, C. _________________ ______, & D. _______. Coil Leaf Air Torsion Bar Automotive Service 6. ______________ weight is all of the weight supported by the springs. __________________ weight is all of the weight not supported by the springs. The more sprung weight, the better the vehicle will ride. Spring, Unspring Sprang, Unsprang Sprung, Unsprung Automotive Service 7. Control arms are connected to the steering knuckles with pivoting joints called ___________ joints. Automotive Service Automotive Service 8. __________ ______________ limit spring oscillations (jounce & rebound), but don’t effect ride height Slack Absorbers Shock Absorbers Shock Restorers Automotive Service 9. ______ shocks are filled with low pressure nitrogen gas to prevent fluid aeration (bubble formation). Gas Water Air Automotive Service 10. Options on shock absorbers include the ________­___________________ feature & adjustable stiffness. Self­Leveling Self­Igniting Self­Energizing Automotive Service Automotive Service Automotive Service 11. A ______ assembly consists of a shock, coil spring & an upper damper/pivot bearing. (No upper ball joint) Strut Strat Shock Automotive Service 12. A ________ bar or stabilizer bar prevents the vehicle body from leaning excessively in sharp turns. Sway Bar Links Sway Bar Stray Sway Bar Bushings Spray Sway Automotive Service 13. A _______ rod controls lateral or side­to­side axle movement during cornering. Track Strut Tie Automotive Service 14. Suspension systems can be of the SHORT­LONG arm, TORSION bar, or the MACPHERSON STRUT design. Slightly modified versions of each type can be found. Automotive Service 15. ____________ suspension systems can be either, independent, Rear semi­independent, or non­independent. Automotive Service 15. ____________ suspension systems can be either, independent, Rear semi­independent, or non­independent. Automotive Service 15. ____________ suspension systems can be either, independent, Rear semi­independent, or non­independent. Automotive Service 15. ____________ suspension systems can be either, independent, Rear semi­independent, or non­independent. Automotive Service 16. Electronic RIDE control systems use computerization to monitor and maintain correct ride height. Automotive Service 17. ACTIVE suspensions use PCM­controlled hydraulics for ride control instead of springs & shocks. ~~~ Automotive Service 18. The _______________ system must provide control of the steering wheels, maintaining the correct amount of effort to transmit “road feel” to the driver’s hands. Steering Suspension Brake Automotive Service Automotive Service 19. In rack & pinion steering, the _______ is a flat steel bar with gear teeth. The _____________ is a small gear that meshes with the rack, it is rotated by the steering wheel and steering shaft. Automotive Service Automotive Service Automotive Service Automotive Service Automotive Service 20. ___________ steering columns help prevent driver chest & face injury during collisions Collapsible Inflatable Regenerative Automotive Service 21. RECIRCULATING ­ BALL & worm gear steering boxes are heavier & more complicated than rack & pinion. Automotive Service 22. On parallelogram steering, the __________ arm and the __________arm support the ends of the center link. Tie rods & tie rod ends connect the steering system center parts to the knuckles. Automotive Service Automotive Service Automotive Service Automotive Service Automotive Service Automotive Service Automotive Service Automotive Service Automotive Service Parallelogram Steering Short­Long Arm Suspension Automotive Service McPherson Strut Suspension Rack & Pinion Steering .
Recommended publications
  • Instructions for M-Xxxx-Xxxx
    M-9602-M Spring and Stabilizer Bar Kit w/ MagneRide Calibration NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS Please visit www. performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS, PLEASE CALL THE FORD PERFORMANCE TECHLINE AT 1-800-367-3788 M-9602-M is designed for 2018+ Mustangs equipped with MagneRide and includes a unique MagneRide calibration that is loaded with the included Procal voucher and software. Please reference the instruction tab on the Procal and make sure you use version 3.9+ Kit Includes: Front Stabilizer Bar Front Springs Rear Stabilizer Bar Rear Springs MagneRide Tuning Calibration Front Stabilizer Bar Removal NOTICE: Suspension fasteners are critical parts that affect the performance of vital components and systems. Failure of these fasteners may result in major service expense. Use the same or equivalent parts if replacement is necessary. Do not use a replacement part of lesser quality or substitute design. Tighten fasteners as specified. 1. Remove all 4 wheels and tires and set aside. 2. On both sides. 1. NOTE: The stabilizer bar links are designed with low friction ball joints that have a low breakaway torque. NOTE: Use the hex-holding feature to prevent the ball stud from turning while removing the stabilizer bar link nut. Remove and the front stabilizer bar link lower nut. 2. Position aside the front stabilizer bar link. Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356 Techline 1-800-367-3788 Page 1 of 41 IS-1850-0631 M-9602-M Spring and Stabilizer Bar Kit w/ MagneRide Calibration NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 4.
    [Show full text]
  • Product Information Sheet Steering and Suspension System Trainer
    Product Information Sheet Steering and Suspension System Trainer This real component trainer provides the instructor with a . Remove, inspect, and install coil springs and spring working light vehicle steering and suspension system for insulators. group or whole-class demonstration. Inspect, replace, and adjust track rod ends, track rod sleeves, and clamps. This includes all the individual components of the system . Remove, inspect, and install upper and lower wishbones, presented on a moveable, steel frame so that each bushes, shafts, and rebound bumpers. component can be clearly identified. Remove, inspect, and install hub carrier assemblies. Inspect, remove, and replace dampers. The system comprises front wheel assemblies, MacPherson strut and coil spring assemblies, road wheels and power Items Included: steering rack. Trainer (right-hand and left-hand drive options available) . The trainer can also be used in conjunction with our Other Items Required: optional cloud-based software, which offers online practical tasks as well as interactive theory presentations, . Automotive workshop tools investigations, and assessments, which link directly to the . AC supply outlet (110V/230V options available) practical activities carried out using this resource. General Information: Trainer Enables Demonstrations of the Following: Trainer Dimensions (W x D x H): . Introduce the steering and suspension system trainer. 1750 x 1250 x 1500 mm / 69 x 49 x 59 inches . Inspect steering shaft universal joint, flexible coupling, Packed Volume: Approx. 3.67m3 / 130ft3 collapsible column, lock cylinder mechanism, and Packed Weight: Approx. 360kg / 795lb steering wheel. Packed Dimensions (W x D x H): . Disassemble, inspect, and reassemble rack and pinion 1904 x 1244 x 1550 mm / 75 x 49 x 62 inches steering gear.
    [Show full text]
  • Ride Control Defined
    RIDE CONTROL DEFINED According to Newton's First Law, a moving body will continue moving in a straight line until it is acted upon by another force. Newton's Second Law states that for each action there is an equal and opposite reaction. In the case of the automobile, whether the disturbing force is in the form of a wind-gust, an incline in the roadway, or the cornering forces produced by tires, the force causing the action and the force resisting the action will always be in balance. Many things affect vehicles in motion. Weight distribution, speed, road conditions and wind are some factors that affect how vehicles travel down the highway. Under all these variables however, the vehicle suspension system including the shocks, struts and springs must be in good condition. Worn suspension components may reduce the stability of the vehicle and reduce driver control. They may also accelerate wear on other suspension components. Replacing worn or inadequate shocks and struts will help maintain good ride control as they: Control spring and suspension movement Provide consistent handling and braking Prevent premature tire wear Help keep the tires in contact with the road Maintain dynamic wheel alignment Control vehicle bounce, roll, sway, dive and acceleration squat Reduce wear on other vehicle systems Promote even and balanced tire and brake wear Reduce driver fatigue Suspension concepts and components have changed and will continue to change dramatically, but the basic objective remains the same: 1. Provide steering stability with good handling characteristics 2. Maximize passenger comfort Achieving these objectives under all variables of a vehicle in motion is called ride control 1 BASIC TERMINOLOGY To begin this training program, you need to possess some very basic information.
    [Show full text]
  • Design and Development of Multi-Link Suspension Suspension System
    ISSN: 2455-2631 © June 2019 IJSDR | Volume 4, Issue 6 Design and Development of Multi-Link Suspension Suspension System 1Piyush Parida, 2Vaibhav Itkikar, 3Harshal Patil, 4Sandip Patil 1,2,3,4UG Students Mechanical Engineering Department G.H. Raisoni College of Engineering and Management, Chas, Ahmednagar, India Abstract: In order to provide a comfortable ride to the passengers and avoid additional stresses in motor car frame, the car should neither bounce or roll or sway the passengers when cornering nor pitch when accelerating. For this purpose the virtual prototype of suspension systems were built in software MSC ADAMS/CAR and suspensions for military truck were analyzed keeping in mind the optimization of suspension parameters. As there is tremendous development in Suspension Technology, Multi-Link suspension system are considered better independent suspension system among all other independent suspension system. Its simple design and construction makes it way more convenient to install and serve its purpose. As there is vast growth in Agriculture, farming becoming more and more advanced in terms of technology and in that transport vehicles play important role in making agriculture more productive. We saw different scenario where agriculture transport vehicles collapsing because of their conventional suspension system fails to stabalize the loaded vehicle on different road conditions. We tried to see the improvement in performance of vehicle in stabalizing itself by using Multi- Link suspension system. Keywords: Suspension, links, vibrations, Multi body dynamic analysis (MBD) 1. INTRODUCTION In heavy transport vehicle field existing dependent suspension system unit is used. If some have that is leaf spring suspension. In all cases Leaf spring design for full load condition.
    [Show full text]
  • Suspension Failures
    www.PDHcenter.com PDHonline Course G493 www.PDHonline.org PDHonline Course G493 (2 PDH) Motor Vehicle Accident Special Topic 3: Suspension Failures Peter Chen, P.E., CFEI, ACTAR 2014 PDH Online | PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658 Phone & Fax: 703-988-0088 www.PDHonline.org www.PDHcenter.com An Approved Continuing Education Provider ©2014 Peter Chen 1 www.PDHcenter.com PDHonline Course G493 www.PDHonline.org Discussion Areas • Understanding the Importance of Suspension Failures as a Potential Cause of Motor Vehicle Accidents. • Basics of Passenger Car/Truck Suspension Systems • Introduction to Suspension Failure Analysis ©2014 Peter Chen 2 www.PDHcenter.com PDHonline Course G493 www.PDHonline.org NHTSA FAR Database • The National Highway Traffic Safety Administration (NHTSA) keeps a database of traffic fatalities called the Fatal Accident Reporting System (FARS). • The database can be found at www.nhtsa.gov/FARS. Take some time to investigate the website and the publicly available information that it holds. • The database goes back to 1975, and the information recorded by NHTSA has changed over time. • The FARS database contains data inputted by police or other traffic governing and/or investigating entities (i.e. sheriff’s departments) detailing the factors behind traffic fatalities on U.S. roads. • The FARS database may be queried by year and vehicle related Factors. ©2014 Peter Chen 3 www.PDHcenter.com PDHonline Course G493 www.PDHonline.org Query of FARS database • A query of the FARS database in 2008 had
    [Show full text]
  • Installation @ Instructions
    \ MN-201 INSTALLATION (0111 0) @ INSTRUCTIONS L J REMOVAL OF REAR SPRINGS 1986 - 1989 VIXEN 21 MOTORHOME, MODELS TD, XC, & SE 1. Remove both side storage covers (rear skirts). 2. Raise vehicle and install safety stands under the rear corners of the frame (ahead of the rear wheels) so the rear tires are off the floor. 3. Remove the rear tire and wheel assemblies. 4. Disconnect the rear height control linkage at the right side of the DeDion tube. 5. While supporting the rear hub bearing carrier, disconnect the rear shocks from the bearing carrier. 6. On TD's and XC's with the manual transaxle, drive out the roll pins securing the inner halfshaft joints to the output shafts. On SE's with the Hydramatic transmission, follow repair manual's procedures to remove rear springs. 7. Slowly and carefully lower the out bearing carrier while sliding the inner halfshaft joint outward until the rear spring can just be removed. Transaxle fluid will leak out and should be caught in a suitable container. 8. Remove the rear suspension bumpers by gripping with water pump pliers and unthreading. Discard. 9. Drill a 112" diameter hole through the center of the upper spring seats and lower crossmember surface. AIR SPRING AND HOSE INSTALLATION 1. Remove the plastic cap from the Air Lift air cylinder and insert the cylinder inside the coil spring with the stem end at the top. 2. Locate desired ''tee" location on the frame rail or cross member. 3. Determine and cut adequate length of tubing to reach from tee to left and right side on air cylinders.
    [Show full text]
  • Clutches for Automobiles and Light Trucks What Does the Clutch Do? Connects the Engine Torque to Transmission When ENGAGED
    Clutches for Automobiles and Light Trucks What does the Clutch do? Connects the engine torque to transmission when ENGAGED Unhooks engine from transmission when DISENGAGED Where is the driver’s foot when clutch is Engaged? OFF the clutch pedal Where is driver foot when clutch is Disengaged? ON the clutch pedal Bellhousing Flywheel Clutch housing Release Bearing Clutch Shaft Throwout bearing & Pilot Bearing Diaphragm Spring Clutch disc hub Clutch disc Pressure Plate Clutch linkage Clutch Fork Throwout fork Bellhousing Clutch housing is also called the Bellhousing Connects and aligns the engine to the transmission. Protects the clutch assembly from water, road debris, etc. Often separate housing for transmission and integral to transaxle housing Engine Transmission Bellhousing Bellhousing Differential Transaxle (transmission AND differential) Flywheel Acts to dampen power stroke acceleration Adds inertia to crankshaft on compression stroke Provides a friction surface for the clutch disc Friction surface finish and cleanliness is critical (Can cause clutch to chatter) Thickness is critical (can be machined too thin to cause dragging clutch) Flywheel add weight to crankshaft for momentum on non‐power strokes Has a ring‐gear for cranking the engine Dual Mass Flywheel Absorbs Engine Vibrations Reduce Gear Noise Smooth Shifting Flywheel friction surface must be perfect Can be removed for re‐surfacing or machining If flywheel is over‐machined (too thin), the clutch moves away from release fork and may drag (not fully release). Also clutch disc may rest on crankshaft bolts causing the clutch to slip Greasy finger prints will cause clutch chatter Flywheels are HEAVY – get help when removing Retaining bolts are critical –use torque wrench –use loctitite If one bolt is bad replace them as a matched set Any imbalance causes vibrations! Wash newly machined flywheel.
    [Show full text]
  • Suspension System, the Stabilizer Bar Should Be Applied to the System in Order to Make a Balance the Vehicle
    0000-00 08-3 1. SPECIFICATION System Description Specification Front Suspension type Macperson strut type suspension Spring type Coil spring Stabilizer type Torsion bar type Shock absorber Type Cylindrical reciprocation type Max. length (extended) 554 mm Min. length 372 mm (compressed) Min. length Inner diameter (A) Upper: 84.0 mm (compressed) Lower: 100.0 mm Outer diameter (B) 163.1 mm Free length (C) 356.1 mm Installed length (D) 276.0 mm Coil windings 5.32 turns Winding direction Right direction Rear Driving type AWD 2WD suspension Suspension type (trailing, upper, lower & track Multi-link type ← rod) Spring type Coil spring ← Stabilizer type Torsion bar type ← Shock absorber Type Cylindrical ← reciprocation type Max. length (extended) 551 mm ← Min. length 361 mm ← (compressed) Coil spring Diameter (A) 12.8 mm 12.6 mm Free length (B) 287.1 mm 291.7 mm Coil windings 6.64 turns 6.32 Winding direction Right direction ← 08-4 1) Wheel Alignment System Description Specification Front Ground clearance (A) 76.8 ± 5 mm Trim height : wheel 433 mm center ↔ Wheel house Camber -0.15 ± 0.5˚ (maintenance free) Caster (maintenance 4.8 ± 0.5˚ free) Total toe-in 0.0 ± 0.1˚ (adjust by tie rod) King pin angle 12.85˚ Rear Ground clearance (A) 63.3 ± 5 mm Trim height : wheel 437 mm center ↔ Wheel house Camber -0.5 ± 0.5˚ (maintenance free) [ adjust by cam bolt on upper arm ] Total toe-in 0.0 ± 0.1˚ [ adjust by cam bolt on track rod ] 0000-00 08-5 2. TIGHTENING TORQUE ▶Front suspension assembly 08-6 ▶Rear suspension assembly 0000-00 08-7 1.
    [Show full text]
  • Driving Near the Limits Dick Maybach, Appalachian Region – PCA [email protected] January 13, 2018
    Driving Near the Limits Dick Maybach, Appalachian Region – PCA [email protected] January 13, 2018 This work is licensed under the Creative Commons Attribution-noncommercial 4.0 International License. To view a copy of this license, visit http://creativecommons.org/licenses/by-nc/4.0/ or send a letter to Creative Commons, PO Box 1866, Mountain View, CA 94042, USA. You are free to: • Share – copy and redistribute the material in any medium or format • Adapt – remix, transform, and build upon the material • The licensor cannot revoke these freedoms as long as you follow the license terms. Under the following terms: • Attribution – You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use. • NonCommercial – You may not use the material for commercial purposes. • No additional restrictions – You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits. This article has two main topics, vehicle dynamics and driving techniques, and concludes with a brief recap. We’ll begin vehicle dynamics by looking at a single tire, because all forces, whether you’re accelerating, braking, or turning, are applied through your tires. Next we’ll look at understeer and oversteer. Understanding these key concepts is essential to maintain control of your car as you maneuver. Another important aspect of vehicle dynamics is weight shifting. As your car changes speed and direction, the distribution of traction among your tires also changes.
    [Show full text]
  • Analytical Models Correlation for Vehicle Dynamic Handling Properties
    Analytical Models Correlation for Vehicle Dynamic Handling Properties Analytical Models Correlation for Daniel Vilela [email protected] Vehicle Dynamic Handling Properties General Motors do Brasil Ltda. Analytical models to evaluate vehicle dynamic handling properties are extremely Vehicle Synthesis interesting to the project engineer, as these can provide a deeper understanding of the Analysis and Simulation Dept. underlying physical phenomena being studied. It brings more simplicity to the overall Sao Caetano do Sul solution at the same time, making them very good choices for tasks involving large 09550-051 SP, Brazil amounts of calculation iterations, like numerical optimization processes. This paper studies in detail the roll gradient, understeer gradient and steering sensitivity vehicle dynamics metrics, starting with analytical solutions available in the literature for these Roberto Spinola Barbosa metrics and evaluating how the results from these simplified models compare against real [email protected] vehicle measurements and more detailed multibody simulation models. Enhancements for Escola Politécnica da Universidade de São Paulo these available analytical formulations are being proposed for the cases where the initial Departamento de Engenharia Mecânica results do not present satisfactory correlation with measured values, obtaining improved Sao Paulo analytical solutions capable of reproducing real vehicle results with good accuracy. 05508-900 SP, Brazil Keywords: handling, vehicle dynamics, analytical solution,
    [Show full text]
  • Car Suspension and Handling Fourth Edition
    Car Suspension and Handling Fourth Edition List of Chapters: Preface to the Fourth Edition 3.8 Tire Uniformity 3.9 Aspect Ratios Preface to the First Edition 3.10 Tire Selection and Air Chamber Geometry Notation 3.11 References Chapter 1 Introduction Chapter 4 Steering 1.1 Scope and Layout of the Book 4.1 Dynamic Function of the Steering 1.2 The Function of the Suspension System System 4.2 Steering Angles: Effects of Tire Slip 1.3 Suspension Geometry Angles and Steering and Suspension 1.4 Kinematics and Compliance (K&C) Kinematics 1.5 Vehicle Dynamics 4.3 Relative Positions of Front- and Rear- 1.6 References Wheel Tracks 4.4 Understeer and Oversteer Chapter 2 Disturbances and Sensitivity 4.5 Directional Stability 2.1 Road Irregularities 4.6 Torque in the Steering System 2.2 Influence of Wheel Size 4.7 Steering Torque Effects Due to 2.3 Subjective Assessment of Ride Steering Geometry 2.4 Human Sensitivity to Vibration 4.8 The Steering Column 2.5 Measurement Standards for Vibration 4.9 Steering Gear 2.6 Influence of Noise on Assessment of 4.10 Constant Velocity (CV) Driveshaft Ride Comfort Joints 2.7 Influence of Phase of Differential 4.11 Torque Steer Effects Vibration on Assessment of Ride 4.12 Front-Wheel Steering Oscillations— Comfort Shimmy 2.8 References 4.13 Power Assistance 4.14 Electric Power Steering Chapter 3 The Wheel and Tire 4.15 Rear-Wheel Steering Systems 3.1 Introduction 4.16 References 3.2 The Wheel Rim 3.3 Tire Size Designation Chapter 5 Suspension Systems and 3.4 Tire Construction Types Their Effects 3.5 Tire Properties
    [Show full text]
  • Suspension by Design
    Version 5.114A June 2021 SusProg3D - Suspension by Design Robert D Small All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the written permission of the publisher. Products that are referred to in this document may be either trademarks and/or registered trademarks of the respective owners. The publisher and the author make no claim to these trademarks. While every precaution has been taken in the preparation of this document, the publisher and the author assume no responsibility for errors or omissions, or for damages resulting from the use of information contained in this document or from the use of programs and source code that may accompany it. In no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this document. Printed: June 2021 Contents 3 Table of Contents Foreword 0 Part 1 Overview 12 1 SusProg3D................................................................................................................................... - Suspension by Design 12 2 PC hardware................................................................................................................................... and software requirements 14 3 To run the..................................................................................................................................
    [Show full text]