DOCSLIB.ORG

Pa-32R-301Sp/Ii Hp/Pa-32R-301T Sp

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Pa-32R-301Sp/Ii Hp/Pa-32R-301T Sp ™ SARATOGA SP SARATOGA II HP MAINTENANCE MANUAL PA-32R-301 SARATOGA SP PA-32R-301 SARATOGA II HP PA-32R-301T SARATOGA SP Card 1 of 4 THIS HANDBOOK INCLUDES THE MAINTENANCE INFORMATION REQUIRED TO BE AVAILABLE BY FAR PART 23. PART NUMBER 761 719 1A1 Published by Technical Publications Piper Aircraft Corporation 2926 Piper Drive Vero Beach, Florida 32960 U.S.A. Copyright 1993 Piper Aircraft Corporation All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the Piper Aircraft Corporation, except for the inclusion of brief quotations in a review. 1A2 PIPER AIRCRAFT PA-32R-301/301T MAINTENANCE MANUAL LIST OF EFFECTIVE REVISIONS Revisions to this Maintenance Manual 761 719 issued Scptembcr 7, 1979 are as follows: Log of Revisions Effectivity Date Aerofiche Card Effectivity PR80014 January 14, 1980 1, 2 and 3 PR800820 August 20, 1980 1, 2 and 3 PR810220 February 20, 1981 1, 2 and 3 PR810923 Septembcr 23, 1981 1, 2 and 3 PR820913 Septembcr 13, 1982 1, 2 and 3 PR821230 December 30, 1982 1, 2 and 3 PR830715 July 15, 1983 1, 2 and 3 PR840810 August 10, 1984 1, 2 and 3 PR850815 August 15, 1985 3 IR860430 April 30, 1986 (Interim) 1 IR860730 July 30, 1986 (Interim) 1 IR860920 September 20, 1986 (Interim)* 1 Revisions to this Maintenance Manual 761 719, reissued July 1, 1993, are as follows: Effective Revisions Page 1 Reissued: July 1, 1993 1A3 PIPER AIRCRAFT PA-32R-301/301T MAINTENANCE MANUAL LIST OF EFFECTIVE REVISIONS Log of Revisions Effectivity Date Aerofiche Card Effectivity Effective Revisions Page 2 Reissued: July 1, 1993 1A4 PIPER AIRCRAFT PA-32R-301/301T MAINTENANCE MANUAL INTRODUCTION TABLE OF CONTENTS/EFFECTIVITY CHAPTER SECTION SUBJECT GRID NO. EFFECTIVITY INTRODUCTION 1A6 July 1, 1993 General 1A6 July 1, 1993 Assignment of Subject Material 1A7 July 1, 1993 Application 1A7 July 1, 1993 Effectivity 1A7 July 1, 1993 Aerofiche 1A8 July 1, 1993 Identifying Revised Material 1A8 July 1, 1993 Serial Number Explanation 1A8 July 1, 1993 System/Chapter Index Guide 1A9 July 1, 1993 Warnings, Cautions and Notes 1A14 July 1, 1993 Supplementary Publications 1A14 July 1, 1993 Vendor Publications 1A15 July 1, 1993 Wire Codes 1A19 July 1, 1993 Introduction Contents Page 1 Reissued: July 1, 1993 1A5 PIPER AIRCRAFT PA-32R-301/301T MAINTENANCE MANUAL INTRODUCTION A. General The Piper PA-32R-301 / 301T Saratoga Maintenance Manual is prepared in accordance with the General Aviation Manufacturers Association (GAMA) Specification No. 2, with respect to the arrangement and content of the System/Chapters within the designated chapter-numbering system. – NOTE – Piper Aircraft Corporation expressly reserves the right to supersede, cancel and/or declare obsolete any part, part numbers, kits or publication that may be referenced in this manual with- out prior notice. – WARNING – USE ONLY GENUINE PIPER AIRCRAFT PARTS OR PIPER AIRCRAFT APPROVED PARTS OBTAINED FROM PIPER APPROVED SOURCES, IN CONNECTION WITH THE MAINTENANCE AND REPAIR OF PIPER AIR- PLANES. Genuine PIPER parts are produced and inspected under rigorous procedures to insure airworthiness and suitability for use in PIPER airplane applications. Parts purchased from sources other than PIPER, even though identical in appearance, may not have had the required tests and inspections performed, may be different in fabrication techniques and materials, and may be dangerous when installed in an airplane. Reworked, salvaged or those parts obtained from non-PIPER approved sources, which the service history is unknown or cannot be authenticated, may have been subjected to unacceptable stresses or temperatures or have other hidden damage, not discernible through routine visual or usual nondestructive testing . This may render the part, component or structural assembly, even though originally manufactured by PIPER AIRCRAFT unsuitable and unsafe for airplane use. PIPER AIRCRAFT expressly disclaims any responsibility for malfunctions, failures, damage or injury caused by use of non-PIPER approved parts. Any question concerning the care of your airplane, be sure to include the airplane serial number in any correspondence. Introduction Page 1 Reissued: July 1, 1993 1A6 PIPER AIRCRAFT PA-32R-301/301T MAINTENANCE MANUAL INTRODUCTION (cont.) B. Assignment of Subject Material The content of this publication is organized at three levels. The three levels are: 1. System/Chapter - The various groups are broken down into major systems such as Environmental Systems, Electrical Power, Landing Gear, etc. The systems are arranged more or less alphabeti- cally rather than by precedence or importance. They are assigned a number, which becomes the first element of the standardized numbering system. Thus, the element “28” of the number 28-40- 01 refers to the chapter “Fuel”. Everything concerning the fuel system will be covered in this chapter. 2. Sub-System/Section - The major systems/chapters of an airplane are broken down into subsys- tems. These sub-systems are identified by the second element of the standard numbering system. The element “40” of the number 28-40-01 concerns itself with the indicating section of the fuel system. 3. Unit/Subject - The individual units within a sub-system/section may be identified by the third ele- ment of the standard numbering system. The element “01” of the number 28-40-01 is a subject designator. This element is assigned at the option of the manufacturer and may or may not be used. C. Application Any publication conforming to the GAMA format will use the same basic numbering system. A per- son wishing information concerning the indication portion of the fuel system, would refer to the System/Chapter Tab 28-Fuel. The table of contents in the front of this chapter will provide a list of sub-systems covered in this chapter. For example, the fuel system chapter with a full index would contain: 28-00 General 28-10 Storage (Tanks, cells, necks, caps, etc.) 28-20 Distribution (Fuel lines, pumps, valves, controls, etc.) 28-30 Dump (If in-flight dumping system is installed) 28-40 Indicating (Quantity, temperature, pressure, etc.) Refer to the table of contents for a complete breakdown and list of the System/Chapters. The material is arranged in ascending numerical sequence. D. Effectivity The Log of Revisions following the title page of the manual is a record of the revisions that have been issued for the manual. Introduction Page 2 Reissued: July 1, 1993 1A7 PIPER AIRCRAFT PA-32R-301/301T MAINTENANCE MANUAL INTRODUCTION (cont.) E. Aerofiche The General Aviation Manufacturers Association (GAMA) have developed specifications for micro- fiche reproduction of aircraft publications. The information compiled in this Aerofiche Maintenance Manual will be kept current by revisions distributed periodically. These revisions will supersede all previous revisions and will be complete Aerofiche card replacements and shall supersede Aerofiche cards of the same number in the set. Conversion of Aerofiche alpha/numeric code numbers: Example: 2J16 = Aerofiche card number two of a given set and grid location J16. First number “2” is the Aerofiche card number. Letter “J” is the horizontal line reference per card. Second number “16” is the vertical line reference per card. F. Identifying Revised Material A revision to a page is defined as any change to the printed matter that existed previously. Revisions, additions and deletions shall be identified by a vertical black line along the left-hand margin of the page opposite only that portion of the printed matter that was changed. A black line in the left-hand margin opposite the chapter/section/subject, page number and date, will indicate that the text was unchanged but the material was relocated to a different page. G. Serial Number Explanation PA-32R-301 Saratoga SP - 1980 Serial Numbers 32R-8013001 thru 32R-8013139 PA-32R-301 Saratoga SP - 1981 Serial Numbers 32R-8113001 thru 32R-8113123 PA-32R-301 Saratogo SP-1982 Serial Numbers 32R-8213001 thru 32R-8213060 PA-32R-301 Saratoga SP- 1993 Serial Numbers 32R-8313001 thru 32R-8313030 PA-32R-301 Saratoga SP-1984 Serial Numbers 32R-8413001 thru 32R-8413024 PA-32R-301 Saratoga SP-1985 Serial Numbers 32R-8513001 thru 32R-8513016 PA-32R-301 Saratoga SP-1986 Serial Numbers 32R-8613001 thru 32R-8613005 and 3213001 thru 3213002 PA-32R-301 Saratoga SP-1987 Serial Numbers 3213003 thru 3213008 PA-32R-301 Saratoga SP-1988 Serial Numbers 3213009 thru 3213019 PA-32R-301 Saratoga SP-1989 Serial Numbers 3213020 thru 3213033 and 3213035 PA-32R-301 Saratoga SP-1990 Serial Numbers 3213034, 3213036, and 3213037 PA-32R-301 Saratoga SP-1992 Serial Numbers 3213038, 3213041 Introduction Page 3 Reissued: July 1, 1993 1A8 PIPER AIRCRAFT PA-32R-301/301T MAINTENANCE MANUAL INTRODUCTION (cont.) G. Serial Number Explanation (cont.) PA-32R-301 Saratoga II HP-1994 Serial Numbers 3213042 and up PA-32R-301T Turbo Saratoga SP - 1980 Serial Numbers 32R-8029001 thru 32R-8029110 and 32R-8029121 PA-32R-301T Turbo Saratoga SP - 1981 Serial Numbers 32R-8129001 thru 32R-8129114 PA-32R-301T Turbo Saratoga SP - 1982 Serial Numbers 32R-8229001 to 32R-8229068 PA-32R-301T Turbo Saratoga SP - 1993 Serial Numbers 32R-8329001 TO 32R-8329040 PA-32R-301T Turbo Saratoga SP - 1984 Serial Numbers 32R-8429001 thru 32R-8429027 PA-32R-301T Turbo Saratoga SP - 1985 Serial Numbers 32R-8529001 thru 32R-8529020 PA-32R-301T Turbo Saratoga SP - 1986 Serial Numbers 32R-8629001 thru 32R-8629005 and 3229001 thru 3229002 PA-32R-301T Turbo Saratoga SP - 1987 Serial Numbers 32R-8629006 and 32290003 H. System/Chapter Index Guide The following System/Chapter, Subsystem Section Index Guide is prepared in accordance with GAMA Specification No. 2 for use with Maintenance Manuals.
Load more

Recommended publications
  • Federal Aviation Administration Joint Aircraft System/Component Code Table and Definitions
    FEDERAL AVIATION ADMINISTRATION JOINT AIRCRAFT SYSTEM/COMPONENT CODE TABLE AND DEFINITIONS INFORMATION LAST UPDATED October 27, 2008 PREPARED BY FEDERAL AVIATION ADMINISTRATION FLIGHT STANDARDS SERVICE REGULATORY SUPPORT DIVISION AVIATION DATA SYSTEMS BRANCH, AFS-620 MIKE MONRONEY AERONAUTICAL CENTER OKLAHOMA CITY, OKLAHOMA 73125 JOINT AIRCRAFT SYSTEM/COMPONENT CODE TABLE PREFACE The Joint Aircraft System/Component (JASC) Code Table is a modified version of the Air Transport Association of America (ATA), Specification 100 code. It was developed by the FAA's, Regulatory Support Division (AFS-600). Over the years, the JASC code format of the ATA Spec 100 code has gained widespread industry acceptance. In a harmonized effort, the FAA’s counterparts in Australia and Canada have adopted the JASC code with only a few exceptions. Some Canadian aircraft manufacturers have also adopted this new standard. This code table is constructed by using the new JASC code four (4) digit format, along with an abbreviated code title. The abbreviated titles have been modified in some cases to clarify the intended use of the accompanying code. This table can be used as a quick reference chart, to assist in the coding and review of aircraft structures or systems data (i.e., Service Difficulty Report (SDR), Accident/Incident Report (AID)). The current coding scheme used in the JASC code was introduced in May 1991, for the technical classification of SDR’s. Its predecessor, the FAA aircraft system/component code, is a similar but more complex eight-digit code, which was developed over 25 years ago. It was constructed around the computer technology of that period.
    [Show full text]
  • Federal Register / Vol. 61, No. 19 / Monday, January 29, 1996 / Rules
    Federal Register / Vol. 61, No. 19 / Monday, January 29, 1996 / Rules and Regulations 2705 of the Federal Aviation Regulations (14 CFR FOR FURTHER INFORMATION CONTACT: tailplanes if the outside air temperatures 21.197 and 21.199) to operate the aircraft to Andrew Gfrerer, Aerospace Engineer, are above +5 degrees Celsius on a location where the requirements of this AD Systems and Equipment Branch, ANM± approach. Ice sublimation, melting, and can be accomplished. 130L, FAA, Transport Airplane shedding are not only functions of (e) This amendment supersedes priority temperature, but also are dependent letter AD 94±11±11, issued June 23, 1994. Directorate, Los Angeles Aircraft (f) This amendment becomes effective on Certification Office, 3960 Paramount upon other factors such as the nature, February 13, 1996. Boulevard, Lakewood, California 90712; size, and extent of ice accretion; Issued in Burlington, Massachusetts, on telephone (310) 627±5338; fax (310) operation of ice protection systems; time January 11, 1996. 627±5210. of flight in temperatures above freezing; Jay J. Pardee, SUPPLEMENTARY INFORMATION: A and airplane speed. proposal to amend part 39 of the Federal The commenter's concern regarding Manager, Engine and Propeller Directorate, incurring a flap extension limitation Aircraft Certification Service. Aviation Regulations (14 CFR part 39) to include an airworthiness directive (AD) after encountering, and then departing, [FR Doc. 96±1410 Filed 1±26±96; 8:45 am] icing conditions has merit. However, the BILLING CODE 4910±13±U that is applicable to various General Dynamics (Convair) airplanes was airplane must be free of ice before the published in the Federal Register on flaps are extended to greater than 30 degrees.
    [Show full text]
  • Aircraft Conceptis Presented
    /OW5/_-7//)-_5°7 77 NASA Technical Memorandum 85777 NASA-TM-85777 19840014485 ¢1 DEVELOPMENTANDANALYSISOFA STOL SUPERSONICCRUISEFIGHTERCONCEPT SAMUEL M, DOLLYHIGH,WILLARD E,Foss,JR,, SHELBY J, MORRIS,JR,,KENNETH B, WALKLEY, E,E, SWANSON, AND A,WARNER ROBINS UOT TO I_F.I'A._'I,[ YRG..'_'i!LqJ llCO;_ MARCH1984 National Aeronautics and I.J,NGLEYRESEARCH,._-_'_rER Space Administration LIBRARY, NAqA Langley Research Center I-L\..'.:PIO;'_,VIRGIIqlA Hampton,Virginia23665 TABLEOF CONTENTS Page SUMMARY.................................. 1 PARTI -" INTRODUCTION........................... 2 PARTII - CONFIGURATIONDESCRIPTION.................... 4 PARTIII - PROPULSIONSYSTEM ....................... 14 PARTIV - MASSPROPERTIES......................... 16 PARTV - AERODYNAMICDESIGNANDANALYSIS ................. 20 PARTVI - CONFIGURATIONSIZING AND PERFORMANCEANALYSIS.......... 69 CONCLUDINGREMARKS............................ 82 SUMMARY - The applicationof advancedand emergingtechnologiesto a fighteraircraft conceptis presented. The concept,which is referredto as the twin-boomfighter - (TBF-1),relieson a two-dimensionalvectoring/reversingnozzleto provideSTOL performancewhile also achievingefficientlong range supersoniccruise. A key feature is that the propulsionpackageis placedso that the nozzlehinge line is near the aircraftcenter-of-gravityto allow largevectorangles and, thus, provide large valuesof directlift while minimizingthe momentsto be trimmed. The confi- gurationname is derivedfrom the long twin boomsextendingaft of the engineto the twin verticaltails
    [Show full text]
  • Airframe Log Entry Piper 32RT-300T
    Aircraft Record General Information M•nufacturer _j?_,_~ ..,P="~r'-------- Model '3.2 ~T ~oT -. ..r ial '32~ - 'J~~ '7 \ :1.~' _______ ____ Registration Num ber >-.lc....li '-~~A D11tc of M•nufacture _ ___________ ____ _______~ -------- - -- I nqlne(s) currently installed: Mmlufacturer ~,_,tP""""'"~--"--;"'--'-'--'~i------- Model l.:L D- ~t..to~ S~A D Serial j)..L. -3.~7 5 - b \ iAi. M11nufacturer ___ ________ Model Serial ___ l,ropeller(s) currently installed: M.1nufacturer _\.i~w~+~-z.~c._\ \'-----------Model HC--i= 3. '-? ~ - 1. ~~ HUD Model ___________ Serial £M__i3_Q_\ ~-~- _ Serial "'·•de Model ___________ Serial _____ Serial ______ Serial m .. de M odel ___________ Serial ___ _ Serial Serial _______ MAKE PIPER ~ !'-,.,.,,.,, HIGH PERFORMANCE AIRCRAFT, INC. DAT E 11912012 MODEL PA-32RT-300T Ne TSN 3699 12 :1 Alterations SIN 32R-7887121 Repaor Station No HPFR569X 3676 07 REG NO 428RA 1850 JOE CROSSON DRIVE TACH ate Number of WORK ORDER El CaJOO CA 92020 5527--09-20 11 Phone 858-576-5000 pecific entries. ) Airframe Entries PERFORMED AN ANNUAL INSPECTION IN ACCORDANCE WITH FAR PART 43, APPENDIX 0 . USING CURRENT PIPER PA32RT-301T {LANCE II) INSPECTION REPORT PIN 230-953 AS A GUIDE. ALL AD'S CHECKED THRU REV 2011 -27, SEE ATIACHED LIST COMPLIED WITH AD 2009-02-03, DATED FEBRUARY 9, 2009 (TO PREVENT A LEAN RUNNING ENGINE. WHICH COULD RESULT IN A SUBSTANTIAL LOSS OF ENGINE POWER AND SUBSTANTIAL, CNTD)-8130 FORM DATED 812712008 SHOWS COMPLIANCE WITH AD 2008-06-51 "G" IS ST AMPED ON HEX PLUG NO FURTHER ACTION REQUIRED COMPLIED WITH AD 80-14-03.
    [Show full text]
  • Design Forum
    JOURNAL OF AIRCRAFT Vol. 42, No. 3, May–June 2005 Design Forum DESIGN FORUM papers range from design case studies to presentations of new methodologies to speculations about emerging design trends. They vary from 2500 to 12,000 words (where a figure or table counts as 200 words). Following informal review by the Editors, they may be published within a few months of the date of receipt. Style requirements are the same as for regular contributions (see inside back cover). Design and Development of the HondaJet Michimasa Fujino∗ Honda R&D Americas, Inc., Greensboro, North Carolina 27409 The HondaJet is an advanced, lightweight, business jet featuring an extra large cabin, high fuel efficiency, and high cruise speed compared to existing small business jets. To achieve the high-performance goals, an over- the-wing engine-mount configuration, a natural-lamina-flow wing, and a natural-laminar-flow fuselage nose were developed through extensive analyses and wind-tunnel tests. The wing is metal, having an integral, machined skin to achieve the smooth upper surface required for natural laminar flow. The fuselage is constructed entirely of composites; the stiffened panels and the sandwich panels are cocured integrally in an autoclave to reduce weight and cost. The prototype aircraft has been designed and fabricated. Major ground tests such as structural proof tests, control-system proof test, system function tests, and ground-vibration tests have been completed. The first flight was conducted on 3 December 2003, and flight testing is currently underway. The aerodynamic, aeroelastic, structural, and systems designs and tests conducted during the development are described Introduction propriate criteria were derived from flight tests.
    [Show full text]
  • Basic Aircraft Construction
    CHAPTER 4 AIRCRAFT BASIC CONSTRUCTION INTRODUCTION useless. All materials used to construct an aircraft must be reliable. Reliability minimizes the possibility of Naval aircraft are built to meet certain specified dangerous and unexpected failures. requirements. These requirements must be selected so they can be built into one aircraft. It is not possible for Many forces and structural stresses act on an one aircraft to possess all characteristics; just as it isn't aircraft when it is flying and when it is static. When it is possible for an aircraft to have the comfort of a static, the force of gravity produces weight, which is passenger transport and the maneuverability of a supported by the landing gear. The landing gear absorbs fighter. The type and class of the aircraft determine how the forces imposed on the aircraft by takeoffs and strong it must be built. A Navy fighter must be fast, landings. maneuverable, and equipped for attack and defense. To During flight, any maneuver that causes meet these requirements, the aircraft is highly powered acceleration or deceleration increases the forces and and has a very strong structure. stresses on the wings and fuselage. The airframe of a fixed-wing aircraft consists of the Stresses on the wings, fuselage, and landing gear of following five major units: aircraft are tension, compression, shear, bending, and 1. Fuselage torsion. These stresses are absorbed by each component of the wing structure and transmitted to the fuselage 2. Wings structure. The empennage (tail section) absorbs the 3. Stabilizers same stresses and transmits them to the fuselage.
    [Show full text]
  • Piper Arrow Questionnaire
    RFC Dallas, Inc. AIRCRAFT QUESTIONNAIRE Version 2; March 12, 2019 Name: ___________________________________________ Date:______________ Aircraft: Arrow Model: PA-28R-200 Registration Number: N1125T Answer the following questions by using the information contained in this aircraft’s Pilot’s Operating Handbook, the current Weight and Balance supplement, placards affixed to the aircraft, the RFC Checklist, and the FARS/AIM. After being reviewed by a Club Checkout Instructor, this questionnaire must be submitted to the RFC Dallas Inc. Safety Officer before solo flights may be conducted. 1. What is the maximum allowable gross weight for this aircraft? _________ lbs. 2. What is the current basic empty weight and moment arm for this aircraft? _________ lbs., __________ inches. 3. How much additional payload weight can be carried assuming maximum fuel on board? _____ lbs. 4. At maximum gross weight, what is the forward C.G. limit? ______ inches. 5. At maximum gross weight, what is the rearward C.G. limit? _____ inches. 6. What is the maximum weight in the Baggage Compartment? _________lbs. 7. The rated HP of the engine at 2700 RPM is: _______HP? 8. What is the fuel capacity: a) Total ________ gals; b) Usable ________ gals. 9. What is the typical grade of aviation fuel approved for use in this aircraft? Octane ____________ / Color ________ 10. During the preflight inspection, there are _______ fuel drains to sump. 11. The proper main strut inflation should be ________inches. The proper nose strut inflation should be ________ inches. 12. Upon an “Alternator Failure” condition, the pilot should: a. __________________________________ b. __________________________________ 1 c.
    [Show full text]
  • A350 Aircraft Characteristics Airport and Maintenance Planning Ac
    @AIRBUS A350 AIRCRAFT CHARACTERISTICS AIRPORT AND MAINTENANCE PLANNING AC The content of this document is the property of Airbus. It is supplied in confidence and commercial security on its contents must be maintained. It must not be used for any purpose other than that for which it is supplied, nor may information contained in it be disclosed to unauthorized persons. It must not be reproduced in whole or in part without permission in writing from the owners of the copyright. Requests for reproduction of any data in this document and the media authorized for it must be addressed to Airbus. © AIRBUS S.A.S. 2005. All rights reserved. AIRBUS S.A.S. Customer Services Technical Data Support and Services 31707 Blagnac Cedex FRANCE Issue: Nov 01/16 Rev: Jul 01/21 @A350 AIRCRAFT CHARACTERISTICS - AIRPORT AND MAINTENANCE PLANNING HIGHLIGHTS Revision No. 10 - Jul 01/21 LOCATIONS CHG DESCRIPTIONS OF CHANGE CODE CHAPTER 2 Section 2-1 Subject 2-1-0 General Aircraft Characteristics Data R CHAPTER 7 Section 7-9 Subject 7-9-0 ACN/PCN Reporting System - Flexible R and Rigid Pavements CHAPTER 10 Section 10-0 Subject 10-0-0 FIGURE Front Page R FIGURE Front Page R HIGHLIGHTS Page 1 Jul 01/21 @A350 AIRCRAFT CHARACTERISTICS - AIRPORT AND MAINTENANCE PLANNING LIST OF EFFECTIVE CONTENT Revision No. 10 - Jul 01/21 CONTENT CHG LAST REVISION CODE DATE CHAPTER 1 Subject 1-1-0 Introduction Jun 01/19 Subject 1-2-0 Glossary Sep 01/19 CHAPTER 2 Subject 2-1-0 General Aircraft Characteristics Data R Jul 01/21 Subject 2-2-0 General Aircraft Dimensions Apr 01/21 FIGURE
    [Show full text]
  • 3Rd – University of Kansas
    Overseer Pedro Toledo AIAA Member Number: 655253 Faculty Advisor: Dr. Ronald Barrett AIAA Member Number: 022393 ii O E S The need for top of the line aircraft has always been a priority in the United States armed forces. Historically, new aircraft for the military have been introduced at a quickened pace. With the sociopolitical forces in recent decades, this trend has slowed down. This can be seen in the date of introduction for the last fi ve members of the fi ghter, F, family: F-35 in 2015, F-22 in 2005, F/A-18 E/F in 1995, F/A-18A/B in 1983, F-16 in 1978, and the F-15 in 1976. Similar trends are found in transport, bombers, air support, and trainer aircraft. With a fl eet of aging airframes, the feasibility of continuously upgrading Cold War-era aircraft with cutting-edge technology is slowly becoming impractical. The purpose of this report is to introduce the A-X Overseer as a replacement to the Fairchild Republic A-10 Thunderbolt II. Preliminary sizing, Class I, and Class II design are presented in this design report. The design process started with preliminary weight, wing, and powerplant sizing. Input from A-10 pilots, fl ight line crew, and ground forces that work alongside the aircraft were consulted. A sweep of potential confi gurations was undertaken for a fi nal selection. Once a fi nal confi guration was selected, Class I and Class II design methods from Jan Roskam’s Airplane Design series were performed. The defi ning feature of the A-X Overseer is the use of the Coandă eff ect through upper surface blowing and a side-mounted cannon.
    [Show full text]
  • 1.3.0.12 ECCAIRS Aviation Data Definition Standard
    ECCAIRS Aviation 1.3.0.12 Data Definition Standard English Attribute Values ECCAIRS Aviation 1.3.0.12 V4 CD Descriptive Factors Aerodrome generally (Aerodrome generally) 40000000 Aerodrome generally: The part played by aerodrome factors in the occurrence. Aerodrome as a structure (Aerodrome as a structure) 41000000 Apron/ramp as an entity (Apron/ramp as an entity) 41300000 N.B. Apron and ramp are synonymous for a defined area, on a land aerodrome, intended to accommodate aircraft for purposes of loading or unloading passengers, mail or cargo, fuelling, parking or maintenance.(Annex 14) Aircraft parking position/gate (Aircraft parking position/gate) 100000118 Apron/ramp congestion (Apron/ramp congestion) 41300200 Apron/ramp obstruction (Apron/ramp obstruction) 41300100 Apron/ramp surface condition (Apron/ramp surface condition) 41300400 Apron/ramp braking action (Apron/ramp braking action) 41300500 Apron/ramp surface state (Apron/ramp surface state) 41300300 Runway as an entity (Runway as an entity) 41100000 Runway. A defined rectangular area on a land aerodrome prepared for the landing and take-off of aircraft. Annex 14. Runway approach obstructions (Approach obstructions) 41100500 All fixed (whether temporary or permanent) and mobile objects that extend above a defined surface intended to protect aircraft in flight. Runway arresting gear (Runway arresting gear) 41100900 Any equipment installed on or after the runway intended to arrest / stop the aircraft. Engineered materials arrestor system (EMAS) (Engineered materials arrestor system 100000120 (EMAS)) An engineered bed of lightweight, crushable concrete built at the end of a runway. Runway safety net (Runway safety net) 100000119 Runway clearway (Runway clearway) 100000056 A defined rectangular area on the ground or water under the control of the appropriate authority, selected or prepared as a suitable area over which an aeroplane may make a portion of its initial climb to a specified height.
    [Show full text]
  • A319 Aircraft Characteristics Airport and Maintenance Planning Ac
    @AIRBUS A319 AIRCRAFT CHARACTERISTICS AIRPORT AND MAINTENANCE PLANNING AC The content of this document is the property of Airbus. It is supplied in confidence and commercial security on its contents must be maintained. It must not be used for any purpose other than that for which it is supplied, nor may information contained in it be disclosed to unauthorized persons. It must not be reproduced in whole or in part without permission in writing from the owners of the copyright. Requests for reproduction of any data in this document and the media authorized for it must be addressed to Airbus. © AIRBUS S.A.S. 2005. All rights reserved. AIRBUS S.A.S. Customer Services Technical Data Support and Services 31707 Blagnac Cedex FRANCE Issue: Jul 01/95 Rev: Dec 01/20 @A319 AIRCRAFT CHARACTERISTICS - AIRPORT AND MAINTENANCE PLANNING HIGHLIGHTS Revision No. 23 - Dec 01/20 LOCATIONS CHG DESCRIPTIONS OF CHANGE CODE HIGHLIGHTS Page 1 Dec 01/20 @A319 AIRCRAFT CHARACTERISTICS - AIRPORT AND MAINTENANCE PLANNING LIST OF EFFECTIVE CONTENT Revision No. 23 - Dec 01/20 CONTENT CHG LAST REVISION CODE DATE CHAPTER 1 Subject 1-1-0 Purpose Nov 01/19 Subject 1-2-0 Glossary Dec 01/17 CHAPTER 2 Subject 2-1-1 General Aircraft Characteristics Data May 01/14 Subject 2-2-0 General Aircraft Dimensions May 01/14 FIGURE General Aircraft Dimensions - Wing Tip Fence Feb 01/18 FIGURE General Aircraft Dimensions May 01/15 Subject 2-3-0 Ground Clearances May 01/15 FIGURE Ground Clearances - Wing Tip Fence Dec 01/18 FIGURE Ground Clearances - Sharklet Dec 01/18 FIGURE Ground Clearances Dec 01/18 FIGURE Ground Clearances - Trailing Edge Flaps - Extended May 01/15 FIGURE Ground Clearances - Flap Tracks - Extended May 01/15 FIGURE Ground Clearances - Flap Tracks - Retracted May 01/15 FIGURE Ground Clearances - Flap Tracks - 1 + F May 01/15 FIGURE Ground Clearances - Aileron Down May 01/15 FIGURE Ground Clearances - Aileron Up May 01/15 FIGURE Ground Clearances - Spoilers - Extended May 01/15 FIGURE Ground Clearances - Leading Edge Slats - Extended May 01/15 Subject 2-4-1 L.E.C.
    [Show full text]
  • Aviation Maintenance Alerts
    ADVISORY CIRCULAR 43-16A AVIATION MAINTENANCE ALERTS ALERT JUNE NUMBER 2006 335 CONTENTS AIRPLANES BEECH ........................................................................................................................................1 BOMBARDIER...........................................................................................................................1 CESSNA ......................................................................................................................................3 DIAMOND ..................................................................................................................................8 GRUMMAN ................................................................................................................................8 LEAR .........................................................................................................................................10 MOONEY..................................................................................................................................11 PILATUS ...................................................................................................................................11 PIPER.........................................................................................................................................11 HELICOPTERS GARLICK (BELL) ....................................................................................................................12 SIKORSKY................................................................................................................................12
    [Show full text]