14 In. Chop Saw

OM-254 208A 2011−08

Description

Accessory

14 In. Chop Saw

File: Accessory www.HobartWelders.com TABLE OF CONTENTs

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING...... 1 1-1. Symbol Usage ...... 1 1-2. Hazards ...... 1 1-3. Additional Symbols For Installation, Operation, And Maintenance...... 2 1-4. California Proposition 65 Warnings...... 3 1-5. Principal Safety Standards ...... 3 SECTION 2 − ADDITIONAL SAFETY PRECAUTIONS...... 4 SECTION 3 − DEFINITIONS ...... 4 3-1. Symbols And Definitions ...... 4 SECTION 4 − SPECIFICATIONS ...... 5 4-1. Chop Saw Components ...... 5 4-2. Specifications ...... 6 4-3. Cutting Capability ...... 6 4-4. Selecting An Extension Cord...... 6 4-5. Included With Your Unit ...... 6 SECTION 5 − INSTALLATION ...... 7 5-1. Serial Number And Rating Label Location...... 7 5-2. Selecting A Location ...... 7 5-3. Adjusting The Depth Of Cut ...... 7 5-4. Adjusting The Vise And Fence...... 8 SECTION 6 − OPERATION ...... 9 6-1. Operating The Cut-Off Saw ...... 9 SECTION 7 − MAINTENANCE ...... 10 7-1. Routine Maintenance ...... 10 7-2. Replacing Motor Brushes And Oiling Bearings...... 10 7-3. Changing The Cut-Off Wheel...... 11 WARRANTY

Hobart is registered to the ISO 9001 Quality System Standard. SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING Pwr. Tools 2011−08 7 Protect yourself and others from injury — read and follow these precautions.

1-1. Symbol Usage

DANGER! − Indicates a hazardous situation which, if Indicates special instructions. not avoided, will result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in the text. Indicates a hazardous situation which, if not avoided, could result in death or serious injury. The possible This group of symbols means Warning! Watch Out! ELECTRIC hazards are shown in the adjoining symbols or ex- SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult sym- plained in the text. bols and related instructions below for necessary actions to avoid the NOTICE − Indicates statements not related to personal injury. hazards. 1-2. Hazards

Turn off all equipment when not in use. Do not leave equipment The symbols shown below are used throughout this manual until it has completely stopped. to call attention to and identify possible hazards. When you see the symbol, watch out, and follow the related instructions Use only well-maintained equipment. Repair or replace damaged to avoid the hazard. The safety information given below is parts at once. Maintain unit according to manual. only a summary of the more complete safety information Keep all panels and covers securely in place. found in the Safety Standards listed in Section 1-5. Read and follow all Safety Standards. HOT PARTS can burn. Only qualified persons should install, operate, maintain, and Do not touch hot parts bare handed. repair this unit. Allow cooling period before working on equipment. During operation, keep everybody, especially children, away. To handle hot parts, use proper tools and/or wear heavy, insulated welding gloves and ELECTRIC SHOCK can kill. clothing to prevent burns. Touching live electrical parts can cause fatal shocks or severe burns. The input power circuit and machine FUMES, GASES, AND PARTICLES can internal circuits are live when power is on. be hazardous. Do not touch live electrical parts. Using this equipment with certain materials may Do not use equipment in damp areas, if movement is confined, or if produce fumes, gases, and particles. Breathing there is a danger of falling. these fumes, gases, and particles can be hazardous to your health. Additional safety precautions are required when any of the follow- ing electrically hazardous conditions are present: in damp Keep your head out of the fumes, gases, and particles. Do not locations or while wearing wet clothing; on metal structures such breathe the fumes, gases, and particles. as floors, gratings, or scaffolds; when in cramped positions such If inside, ventilate the area and/or use local forced ventilation to re- as sitting, kneeling, or lying; or when there is a high risk of unavoid- move fumes, gases and particles. able or accidental contact with the equipment. And, do not work alone! If ventilation is poor, wear an approved air-supplied respirator. Disconnect input power before installing or servicing this equip- Read and understand the Material Safety Data Sheets (MSDSs) ment. and the manufacturer’s instructions for metals, consumables, coatings, cleaners, and degreasers. Properly install and ground this equipment according to its Work in a confined space only if it is well ventilated, or while Owner’s Manual and national, state, and local codes. wearing an air-supplied respirator. Always have a trained watch- Always verify the supply ground − check and be sure that input person nearby. Fumes, gases, and particles can displace air and power cord ground wire is properly connected to ground terminal in lower the oxygen level causing injury or death. Be sure the breath- disconnect box or that cord plug is connected to a properly ing air is safe. grounded receptacle outlet. Do not work in locations near degreasing, cleaning, or spraying Do not touch grounded surfaces when using this equipment (metal operations. pipes, enclosures, structures, etc.). Do not work on materials that may contain hazardous substances, When making input connections, attach proper grounding conduc- including masonry, treated lumber, and items with lead-based tor first − double-check connections. paint. Do not work on on coated metals, such as galvanized, lead, or cadmium plated steel, unless the coating is removed from the Keep cords dry, free of oil and grease, and protected from hot metal work area, the area is well ventilated, and while wearing an air- and sparks. supplied respirator. Coatings and any materials containing these Frequently inspect input power cord for damage or bare wiring − elements can give off toxic fumes, gases, and particles when replace cord immediately if damaged − bare wiring can kill. worked on.

OM-254 208 Page 1 SPARKS can cause fire or explosion. FLYING METAL or DIRT can injure eyes.

Welding, chipping, wire brushing, and grinding Sparks can fly off from the equipment. The flying sparks, hot workpiece, and hot equipment can cause sparks and flying metal. As welds cool, cause fires and burns. Accidental contact with metal they can throw off slag. objects can cause sparks, explosion, overheating, Wear approved safety glasses with side or fire. Check and be sure the area is safe before doing any work. shields even under your welding helmet. Remove all flammables within 35 ft (10.7 m) of the equipment. If this is not possible, tightly cover them with approved covers. Do not work where flying sparks can strike flammable material. Protect yourself and others from flying sparks and hot metal. NOISE can damage hearing. Be alert that sparks and hot materials can easily go through small cracks and openings to adjacent areas. Noise from some processes or equipment can damage hearing. Watch for fire, and keep a fire extinguisher nearby. Do not work where the atmosphere may contain flammable dust, Wear approved ear protection if noise level is gas, or liquid vapors (such as gasoline). high. Wear oil-free protective garments such as a heavy shirt, cuffless trousers, high shoes, and a cap. Remove any combustibles, such as a butane lighter or matches, from your person before doing any work. After completion of work, inspect area to ensure it is free of sparks, glowing embers, and flames. Use only correct fuses or circuit breakers. Do not oversize or by- pass them. Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B for hot work and have a fire watcher and extinguisher nearby.

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard. MOVING PARTS can injure.

Do not install or place unit on, over, or near Keep away from moving parts. combustible surfaces. Keep all doors, panels, covers, and guards Do not install unit near flammables. closed and securely in place. Do not overload building wiring − be sure power supply system is Have only qualified persons remove doors, panels, covers, or properly sized, rated, and protected to handle this unit. guards for maintenance and troubleshooting as necessary. Reinstall doors, panels, covers, or guards when maintenance is finished and before reconnecting input power. Do not wear clothing, gloves, or jewelry, or other items that may FALLING EQUIPMENT can injure. be caught in moving parts. Wear a hat or other covering to contain long hair. Use equipment of adequate capacity to lift and Do not make adjustments on moving equipment. Remove ad- support unit. justing tools (keys, wrenches) before using equipment. Keep equipment (cables and cords) away from Verify the switch is in the Off position before plugging in the moving vehicles when working from an aerial equipment. location. Use the equipment only for the recommended application and at Do not stand on the equipment. the specified rate. Do not use the equipment for tasks for which it If applicable, bolt equipment to a smooth surface large and is not intended. strong enough to safely support it. Do not hold workpiece in your hand when using equipment. Use Follow the guidelines in the Applications Manual for the Revised a vice or clamp to hold workpiece. NIOSH Lifting Equation (Publication No. 94−110) when manu- ally lifting heavy parts or equipment. READ INSTRUCTIONS.

Read and follow all labels and the Owner’s Manual carefully before installing, operating, or FLYING SPARKS can injure. servicing unit. Read the safety information at the beginning of the manual and in each Wear a face shield to protect eyes and face. section. Operate equipment with proper guards, and in Use only genuine replacement parts from the manufacturer. a safe location while wearing proper face, and body protection. Perform maintenance and service according to the Owner’s Manuals, industry standards, and national, state, and local Sparks can cause fires — keep flammables away. codes.

OM-254 208 Page 2 1-4. California Proposition 65 Warnings

Battery posts, terminals and related accessories contain lead This product contains chemicals, including lead, known to and lead compounds, chemicals known to the State of the state of California to cause cancer, birth defects, or other California to cause cancer and birth defects or other reproductive harm. Wash hands after use. reproductive harm. Wash hands after handling. 1-5. Principal Safety Standards

National Electrical Code, NFPA Standard 70, from National Fire Protec- Standard for Fire Prevention During Welding, Cutting, and Other Hot tion Association, Quincy, MA 02269 (phone: 1-800-344-3555, website: Work, NFPA Standard 51B, from National Fire Protection Association, www.nfpa.org and www. sparky.org). Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org. Safe Practice For Occupational And Educational Eye And Face Protec- U.S. Consumer Product Safety Commission (CPSC), 4330 East West tion, ANSI Standard Z87.1, from American National Standards Institute, Highway, Bethesda, MD 20814 (phone: 301-504-7923, website: 25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web- www.cpsc.gov). site: www.ansi.org). Applications Manual for the Revised NIOSH Lifting Equation, The Na- OSHA, Occupational Safety and Health Standards for General Indus- tional Institute for Occupational Safety and Health (NIOSH), 1600 try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q, Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website: and Part 1926, Subpart J, from U.S. Government Printing Office, Super- www.cdc.gov/NIOSH). intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954 (phone: 1-866-512-1800) (there are 10 OSHA Regional Offices— phone for Region 5, Chicago, is 312-353-2220, website: www.osha.gov).

OM-254 208 Page 3 SECTION 2 − ADDITIONAL SAFETY PRECAUTIONS

! Do not use this equipment unless ! Test all cut-off wheels before use ac- ! Do not apply excessive force to the you are sure it is correctly as- cording to the cut-off wheel manu- cut-off wheel or the wheel may break sembled and working properly. facturer’s instructions. or be damaged. ! Turn off saw and disconnect input ! Stand to the side of the saw at power cord before installing, adjust- ! Store cut-off wheels in a dry location start-up. Run saw at normal operating, or servicing this equipment. where they are protected against ing speed for one minute before us- ! Use GFCI protection when operat- damage from impact, chemicals, ing. ing this equipment outdoors or in a and extreme temperatures. damp location. If GFCI receptacle is ! Do not start the saw with the cut-off not available, use a GFCI-protected wheel touching the workpiece. extension cord. ! Do not overtighten the hardware securing the cut-off wheel. ! Use wheel flanges when mounting ! Use only cut-off wheels with a bore cut-off wheel. Use only the wheel equal to the arbor (spindle) on the flanges supplied with the saw. chop saw. Do not modify a cut-off ! Use only cut-off wheels suitable for wheel to fit the chop saw arbor. this equipment. Do not use cut-off ! Keep power cord away from the cut-off wheel. ! Inspect cut-off wheel for damage be- wheels rated lower than 3500 RPM. fore use. Replace damaged or vi- Do not use toothed blades. Do not ! Do not adjust guards, shields, brating cut-off wheel. Dispose of use saw to cut magnesium, plastic, fence, or vise while the saw is run- damaged cut-off wheel. or wood. ning.

SECTION 3 − DEFINITIONS

3-1. Symbols And Definitions

A Amperage V Voltage Hz Hertz On Revolutions or re- Alternating Current Off Watt … ciprocation per W (AC) /min minute (RPM) Notes

OM-254 208 Page 4 SECTION 4 − SPECIFICATIONS

4-1. Chop Saw Components

1 Operating Handle 2 Trigger Lock Hole 3 Upper Guard 1 2 4 6 Ft (1.8 m) 115 Volt Power Cord w/Grounded Plug 3 5 Cutting Head 6 Vise 7 Vise Handle 4 8 Work Table (Base) 9 Vise Locking Lever 10 Fence 11 Cut-Off Wheel 12 Lower Guard 13 Trigger 14 Carrying Handle 5 15 Safety Trigger 12 16 Spindle Lock 17 Locking Pin 18 Depth Of Cut Adjustment Screw NOTICE − Lock down cutting head be- 11 fore transporting or storing machine. To 9 10 lock down cutting head, press cutting 8 head down and push in locking pin. To unlock cutting head, push down cutting head and pull locking pin out.

7 6

OM-254 208 Page 5 4-2. Specifications

Voltage Amperage/ No Load Max Overall Noise (dB(A)) Weight Rating Watts Speed Horse Power Dimensions Length: 22.0 in. (560 mm) 37 lb 120 Volts AC, 15 Amps Lp=89.6 Width: 12.6 in. 3500 RPM 2.5 HP (16.8 kg) 60 Hz 1800 Watts Lw=102.6 (320 mm) Height: 17 in. (430 mm) Operating linear velocity of the cut-off wheel is greater than or equal to 265.5 feet per second (90 m/s)

4-3. Cutting Capability

Cutting Capability

Type 90°/45° 90° 45° 90° 90°

4.5 in. (115 mm) 4.7 in. (120 mm) 4.2 in. (106 mm) 4.0 x 7.8 in. (102 x 197 mm) 5.5 in. (139 mm)

Maximum cutting depth is 3.5 in. (90 mm).

4-4. Selecting An Extension Cord

Amperage Rating Volts 25 Ft 50 Ft 100 Ft 150 Ft

15 Amps 120 Volts 14 Ga 12 Ga Not Recommended

Make sure extension cord is in good condition. If extension cord is to be used outdoors, make sure it is rated for outdoor use.

4-5. Included With Your Unit

1 Motor Brush Assembly 1 2 (Replacement). See Section 7-2. 2 Allen Wrench For additional options and acces- 8 mm sories, contact your distributor.

OM-254 208 Page 6 SECTION 5 − INSTALLATION

5-1. Serial Number And Rating Label Location The serial number and rating information for this product is located on the front. Use rating label to determine input power requirements and/or rated output. For future reference, write serial number in space provided on back cover of this manual. 5-2. Selecting A Location

! Use GFCI protection when oper- 1 2 ating this equipment outdoors or in a damp location. If GFCI receptacle is not available, use a GFCI-protected extension cord. ! Special installation may be required where gasoline or volatile liquids are present − see NEC Article 511 or CEC Section 20. ! Be sure the workbench or other support stand will support the weight of the equipment. 1 Grounded Receptacle − NEMA Type 5−15R (Customer Supplied) For 115 volt AC input power, a 15 ampere individual branch circuit protected by time-delay fuses or circuit breaker is required. 2 Plug From Unit ! Do not move or operate unit where it could tip. If an extension cord is required, see Section 4-4.

5-3. Adjusting The Depth Of Cut

! Disconnect input power cord before installing, adjusting, or servicing this equipment.

Maximum cutting depth is 3-1/2 in. (90 mm). 1 Depth Of Cut Adjustment 1 Screw 2 Jamb Nut Use the depth of cut adjustment screw to adjust or change the depth of cut. When correctly adjusted, the depth of cut adjustment screw prevents 2 the cut-off wheel from making contact with anything below the base. To adjust depth of cut, proceed as follows: Loosen jamb nut. Adjust the depth of cut adjustment Tools Needed: screw to the correct height. Tighten jamb nut. 1/2 in. (13 mm)

OM-254 208 Page 7 5-4. Adjusting The Vise And Fence

Tools Needed:

8 mm (Supplied)

Photo 2

1 234 5

! Turn off saw and disconnect input Positioning The Fence To change the angle of the fence, loosen power cord before installing, ad- the two fence screws and rotate fence to justing or servicing this equipment. The fence can be moved forward or back, the desired position. Tighten screws. and the angle of the fence can be rotated 0 1 Fence Location Holes to 45° left or right as needed. Positioning The Vise Make sure workpiece is flat on base and 2 Fence Screws For better cutting results, position tight against the fence in desired position. 3 Fence workpiece flat on the base, directly below the centerline of the cut-off wheel Lift locking lever. 4 Vise (see photo 2). Slide vise up against workpiece. 5 Locking Lever There are four holes in the base to accom- Push locking lever down and turn vise modate different size workpieces. handle clockwise to tighten and secure 6 Handle workpiece against fence. To move the fence, remove the two fence Use vise and fence to position workpiece screws and position the fence where To loosen vise, turn vise handle counter- where desired. needed. Install and tighten screws. clockwise while lifting locking lever.

OM-254 208 Page 8 SECTION 6 − OPERATION

6-1. Operating The Cut-Off Saw

3 2 1

Tools Needed:

Respirator

! Do not use this equipment unless ! Stand to the side of the saw at Operating The Cut-Off Saw you are sure it is correctly as- start-up. Run saw at normal operat- sembled and working properly. ing speed for one minute before us- Adjust fence and vise to secure workpiece ! Turn off saw and disconnect input ing. to base (see Section 5-4). power cord before installing, ad- ! Do not apply excessive force to the justing or servicing this equipment. cut-off wheel or the wheel may Check condition of cut-off wheel. ! Do not adjust guards, shields, break or be damaged. fence, or vise while the saw is Connect input power. running. ! Do not make a free-hand cut. Use ! Use only cut-off wheels suitable for clamps or similar device to secure Slide safety trigger back while lifting trigger. this equipment. Do not use cut-off workpiece to base. wheels rated lower than 3500 RPM. ! Keep power cord away from the Do not use toothed blades. Do not Slowly and smoothly lower cut-off wheel cut-off wheel. use saw to cut magnesium, plastic, onto workpiece. or wood. ! Store cut-off wheels in a dry loca- ! Use only cut-off wheels with a bore tion where they are protected Allow wheel to cut all the way through work- equal to the arbor (spindle) on the against damage from impact, chem- piece. Do not attempt to exceed the max- chop saw. Do not modify a cut-off icals, and extreme temperatures. imum cutting depth of this machine. wheel to fit the chop saw arbor. Raise wheel completely, release trigger 1 Handle and wait for wheel to stop. ! Inspect cut-off wheels for damage before use. Replace damaged or vi- 2 Trigger Lock Hole brating cut-off wheels. 3 Trigger When not in use, a padlock may be in- ! Test all cut-off wheels before use ac- 4 Safety Trigger serted into the trigger lock hole to help cording to the cut-off wheel manu- prevent the accidental starting of the facturer’s instructions. 5 Workpiece machine.

OM-254 208 Page 9 SECTION 7 − MAINTENANCE

7-1. Routine Maintenance

! Turn off saw and disconnect input power before installing or servicing this equipment.

Service equipment more often if used in severe conditions.

Do not use cleaners and solvents (including gasoline, tetrachloride, and ammonia) that may damage plastic parts.

= Check = Change = Clean = Replace

* To be done by Factory Authorized Service Agent

Every Clean and lubricate pivot axle. 40 Hours Every Month

Outer Surfaces Outer Surfaces And Around Base Of Power Cord Machine. Every Check motor brushes and replace if 3 necessary (see Section7-2) . Months

Unreadable Labels

7-2. Replacing Motor Brushes And Oiling Bearings

! Turn off saw and disconnect input power cord before installing, adjusting, or servicing this equipment.

After 40 hours of operation, 1/4 in. (6 mm) check brushes and replace if there is less than1/4 in. (6 mm) of brush remaining. 1 Brushes must be replaced in pairs. 1 Motor Brush Cap 2 Motor Brush Assembly

2 Remove brush cap. Remove brush assembly and replace with new brush assembly. Reinstall cap.

ÉÉÉÉ After replacing motor brush(es), let motor run at no

ÉÉÉÉ load speed for 10 minutes.

Tools Needed: ÉÉÉÉ

ÉÉÉÉ

ÉÉÉÉ ÉÉÉÉ

OM-254 208 Page 10 7-3. Changing The Cut-Off Wheel

! Turn off saw and disconnect input power cord before installing, adjusting, or servicing this equipment. ! Use only cut-off wheels with a bore equal to the arbor (spindle) on the cut-off saw. Do not modify a cutting wheel to fit the cut-off saw arbor. ! Use only cut-off wheels suitable 1 for this equipment. Do not use cut-off wheels rated lower than 3500 RPM. Do not use toothed blades. Do not use saw to cut magnesium, plastic, or wood. ! Use only cut-off wheels with a bore equal to the arbor (spindle) on the chop saw. Do not modify a cut-off wheel to fit the chop saw arbor. ! Inspect cut-off wheels for damage before use. Replace damaged or vibrating cut-off wheels. ! Test all cut-off wheels before use according to the cut-off wheel manufacturer’s instructions. 2 ! Do not overtighten the hardware securing the cut-off wheel. ! Do not use this equipment unless you are sure it is correctly as- sembled and working properly.

The cut-off wheel should be replace when 1/3 of the diameter has been 7 worn away. 1 Lower Guard 6 3 2 Spindle 5 3 Inner-flange 4 4 Cut-Off Wheel 5 Outer-flange 6 Side Cover 7 Hex Screw 8 Spindle Lock Changing The Cut-Off Wheel Raise lower guard. Engage spindle lock in hole in cut-off wheel. Use supplied wrench to remove hex screw, side cover, outer-flange, and old cut-off wheel. Do not remove inner-flange. Make sure the mounting surfaces of the inner and outer flanges are clean, smooth, and free of any burrs. Mount replacement cut-off wheel on spindle, and secure with outer-flange, side cover, and hex screw. ! After replacing a cut-off wheel, let unit run at no load speed for three minutes. 8 Tools Needed:

8 mm (Supplied)

OM-254 208 Page 11 Notes

TM-216 869 Page 12 Dynasty 350/700, Maxstar 350/700 Effective January 1, 2011 Warranty Questions? 5/3/1 WARRANTY applies to all Hobart welding equipment, plasma cutters and spot welders with a serial number preface of MB or newer. Call This limited warranty supersedes all previous Hobart warranties and is exclusive with 1-800-332-3281 no other guarantees or warranties expressed or implied. 7 AM − 5 PM EST Hobart products are serviced by Hobart or Miller Authorized Service Agencies. LIMITED WARRANTY − Subject to the terms and conditions Hobart’s 5/3/1 Limited Warranty shall not apply to: below, Hobart/Miller Electric Mfg. Co., Appleton, Wisconsin, 1. Consumable components; such as contact tips, Service warrants to its original retail purchaser that new Hobart equipment sold after the effective date of this limited warranty is cutting nozzles, contactors, brushes, relays, work You always get the fast, station table tops and welding curtains, or parts that reliable response you free of defects in material and workmanship at the time it is shipped by Hobart. THIS WARRANTY IS EXPRESSLY IN LIEU fail due to normal wear. (Exception: brushes and need. Most replacement OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, relays are covered on all engine-driven products.) parts can be in your INCLUDING THE WARRANTIES OF MERCHANTABILITY AND hands in 24 hours. FITNESS. 2. Items furnished by Hobart/Miller, but manufactured by others, such as engines or trade accessories. These Support Within the warranty periods listed below, Hobart/Miller will repair items are covered by the manufacturer’s warranty, if Need fast answers to the or replace any warranted parts or components that fail due to any. tough welding questions? such defects in material or workmanship. Hobart/Miller must be notified in writing within thirty (30) days of such defect or failure, at 3. Equipment that has been modified by any party other Contact your distributor or which time Hobart/Miller will provide instructions on the warranty call 1-800-332-3281. The claim procedures to be followed. than Hobart/Miller, or equipment that has been expertise of the distributor improperly installed, improperly operated or misused Hobart/Miller shall honor warranty claims on warranted based upon industry standards, or equipment which has and Hobart is there to equipment listed below in the event of such a failure within the help you, every step of not had reasonable and necessary maintenance, or warranty time periods. All warranty time periods start on the equipment which has been used for operation outside of the way. delivery date of the equipment to the original retail purchaser, and not to exceed one year after the equipment is shipped to a North the specifications for the equipment. Assistance American distributor or eighteen months after the equipment is Visit the Hobart website: HOBART PRODUCTS ARE INTENDED FOR PURCHASE AND shipped to an International distributor. USE BY COMMERCIAL/INDUSTRIAL USERS AND PERSONS www.HobartWelders.com 1. 5 Years — Parts and Labor TRAINED AND EXPERIENCED IN THE USE AND * Original Main Power Rectifiers only to include SCRs, MAINTENANCE OF WELDING EQUIPMENT. diodes, and discrete rectifier modules In the event of a warranty claim covered by this warranty, the * Reactors exclusive remedies shall be, at Hobart’s/Miller’s option: (1) repair; or (2) replacement; or, where authorized in writing by * Stabilizers Hobart/Miller in appropriate cases, (3) the reasonable cost of * Transformers repair or replacement at an authorized Hobart/Miller service station; or (4) payment of or credit for the purchase price (less 2. 3 Years — Parts and Labor reasonable depreciation based upon actual use) upon return of * Drive Systems the goods at customer’s risk and expense. Hobart’s/Miller’s option of repair or replacement will be F.O.B., Factory at * Idle Module Appleton, Wisconsin, or F.O.B. at a Hobart/Miller authorized * PC Boards service facility as determined by Hobart/Miller. Therefore no * Rotors, Stators and Brushes compensation or reimbursement for transportation costs of any kind will be allowed. * Solenoid Valves TO THE EXTENT PERMITTED BY LAW, THE REMEDIES * Spot Welder Transformer PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE * Switches and Controls REMEDIES. IN NO EVENT SHALL HOBART/MILLER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR 3. 1 Year — Parts and Labor Unless Specified CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF (90 days for industrial use) PROFIT), WHETHER BASED ON CONTRACT, TORT OR ANY * Accessories OTHER LEGAL THEORY. * Batteries (Trek 180 Only) ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND * Contactors ANY IMPLIED WARRANTY, GUARANTY OR REPRESENTATION AS TO PERFORMANCE, AND ANY * Field Options REMEDY FOR BREACH OF CONTRACT TORT OR ANY (NOTE: Field options are covered for the remaining OTHER LEGAL THEORY WHICH, BUT FOR THIS PROVISION, warranty period of the product they are installed in, or MIGHT ARISE BY IMPLICATION, OPERATION OF LAW, for a minimum of one year — whichever is greater.) CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING * Flowgauge and Flowmeter Regulators (No Labor) ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, WITH RESPECT TO * HF Units ANY AND ALL EQUIPMENT FURNISHED BY * MIG Guns/TIG Torches HOBART/MILLER IS EXCLUDED AND DISCLAIMED BY Hobart/Miller. * Motor-Driven Guns * Plasma Cutting Torches Some states in the U.S.A. do not allow limitations of how long an implied warranty lasts, or the exclusion of incidental, indirect, * Regulators special or consequential damages, so the above limitation or * Relays exclusion may not apply to you. This warranty provides specific legal rights, and other rights may be available, but may vary from WELDING PRODUCTS * Remote Controls state to state. * Replacement Parts (No labor) − 90 days In Canada, legislation in some provinces provides for certain * Running Gear/Trailers additional warranties or remedies other than as stated herein, * Water Coolant Systems and to the extent that they may not be waived, the limitations and exclusions set out above may not apply. This Limited Warranty 4. Engines, batteries (except Trek 180) and tires are provides specific legal rights, and other rights may be available, warranted separately by the manufacturer. but may vary from province to province. hobart_warr 2011−01 Thank you for purchasing Hobart. Our trained technical support team is dedicated to your satisfaction. For questions regarding performance, operation, or service, contact us!

Resources Available Always provide Model Name and Serial/Style Number.

To locate a Service Center: Call 1-800-332-3281 or visit our website at www.HobartWelders.com/wheretobuy

For Technical Assistance: Call 1-800-332-3281 7 AM to 5 PM EST − Monday through Friday

Owner’s Record Please complete and retain with your personal records.

Model Name Serial/Style Number

Purchase Date (Date which equipment was delivered to original customer.)

Distributor

Address Hobart Welding Products An Illinois Tool Works Company City 600 West Main Street Troy, OH 45373 USA For Assistance: State Zip Call1-800-332-3281