GR500/T240 Capacitors CAPACITOR OUTLINE DRAWINGS

GR500 HIGH RELIABILITY SOLID TANTALUM

GR500 INDEX

Introduction ...... 3

GR500/T210 ordering information ...... 4 ratings and part number reference ...... 4-6 capacitor markings ...... 6 applications information ...... 7-10

GR500/T220 ordering information ...... 11 ratings and part number reference ...... 12-13 capacitor markings ...... 13 applications information ...... 13-16

GR500/T240 ordering information ...... 17 ratings and part number reference ...... 18 capacitor markings ...... 18 applications information ...... 19-21

GR500 GRADED RELIABILITY SPECIFICATION scope ...... 22 applicable documents ...... 22 requirements ...... 22-24 quality assurance provisions ...... 24-27 preparation for delivery ...... 27 certified grading papers ...... 28-29

Notice Although the information in this catalog has been carefully checked for accuracy, and is believed to be correct and current, no warranty, either express or implied, is made to either its applicability to, or its compatibility with, specific requirements; nor does KEMET Electronics Corporation assume any respon- sibility for correctness of this information, nor for damages con- sequent to its use. All design characteristics, specifications, tolerances, and the like are subject to change without notice.

2 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500 HIGH RELIABILITY SOLID TANTALUM

Introduction +125°C prior to the electrical testing which eliminates The solid tantalum capacitor has become an essential device those capacitors failing to withstand this extreme in circuits requiring high capacitance-voltage product and change in environment. extended environmental capability. The KEMET GR500 2. Surge Current — Each GR500 capacitor receives Graded Reliability concept has made available state-of-the- 10 cycles @ -55°C, + 85°C. Each cycle consists of rated art devices providing maximum assurance of meeting sys- voltage charge for 4±1 seconds and a discharge for 4±1 tem reliability goals. All Graded Reliability capacitors seconds. Total DC resistance (excluding the test capac- receive meticulous attention from raw material selection itor) is ≤1.0 ohms. The energy storage bank capacitor(s) through manufacture, final inspection and shipping. Having is 100,000 µF minimum. survived a very stringent quality control program, the result- 3. Grading — This term is used to describe the tech- ing capacitors meet or exceed the most critical requirements nique which defines the failure rate of KEMET Graded of space, satellite, missile and medical applications where Reliability capacitors. Grading consists of placing failure is, at best, expensive, and at worst, fatal. GR500 capacitors in an oven at 85°C for a minimum of KEMET is, therefore, committed to the principle of the 250 hours at a voltage greater than rated voltage. The highest possible reliability in the manufacture and grading of technique is fundamentally based upon the oft-docu- its GR500 Series capacitors. mented fact that solid tantalum capacitors do not con- The KEMET GR500 High Reliability concept disallows form to the exponential distribution of time-ordered fail- grouping of diverse ratings and production batches to deter- ures, but instead exhibit a constantly decreasing failure mine average failure rates. Instead, data from each and every rate. The Weibull distribution provides a valuable tool capacitor batch are statistically fitted to determine failure for describing the behavior of solid tantalum capacitors, rate on the basis of 100% life testing. Each homogeneous and experimental fits are made to this distribution in production batch is “graded’’ as a single inspection lot, and determining performance levels for each GR500 Series documented evidence of failure rate achieved is supplied batch. Actual test data are provided with each shipment with the parts, providing assurance of the most sophisticated of capacitors to document the failure rate obtained. and accurate reliability measurement method in the industry. 4. Electrical Testing — Each GR500 Series capacitor is tested at 25°C for leakage current at rated voltage, as Basic Requirements well as capacitance and dissipation factor at 120 Hz. A. Manufacturing Environment — It is of vital impor- Since uniformity is generally a valid indicator of relia- tance that high reliability electronic components be manu- bility, parametric distributions are graphically recorded factured in an environment which provides commitment to for each lot. Parts which deviate from the normal popu- the philosophy of high reliability production. GR500 Series lation are discarded. Guaranteed maximum values are capacitors are manufactured in a plant area that stresses this as detailed in Table 1. philosophy. Manufacturing and quality control personnel 5. ESR — Each GR500 capacitor is tested for ESR @ are selected for experience and competence. Extensive 100 KHz. See electrical specification tables. training in quality and reliability assurance techniques is 6. X-ray — Each GR500 Series capacitor is examined provided, and motivation of personnel is heavily stressed. by X-ray in two planes with 90 degree rotation. Since Raw material and in-process inspection techniques are assembly of the solid tantalum capacitor is a blind oper- especially rigid. The result is a capacitor product of inher- ation, optical inspection cannot reveal internal defects ently superior quality. such as loose solder balls or deficient anode solder B. Screening Test — All GR500 Series capacitors are sub- bonding. jected to a broad test program. Despite the most rigid of 7. Hermeticity — Each GR500 capacitor receives her- quality control procedures, some variation among batches of meticity testing per MIL-STD-202, Method 112, capacitors must be recognized. This fact is understandable Condition D. This test uses a fluorocarbon liquid at when one considers the inherent differences which derive 125°C±5° (257°F± 9°F) at ambient pressure and detects from the 16 to 1 ratio of operating voltages, the 20 to 1 ratio gross leaks by the observation of bubbles. of physical sizes, and the 60,000 to 1 ratio among capaci- C. Sampling — In addition to the 100% screening tests, tance ratings. Maximum assurance of reliability is achieved other tests are imposed on a sample basis to determine para- by maintaining batch identity from the raw material with metric stability and resistance to environmental extremes. respect to capacitor sizes and ratings as well as material These tests are fully described in the GR500 Graded identification. Each batch is then subjected to extensive, Reliability Specification. non-destructive 100% screening tests as indicated below. D. Available Special Testing — In addition to the standard 1. Thermal Shock — Inherent variations exist among testing outlined in this catalog, optional testing is available. the temperature coefficients of expansion of the various 1. 100% ESR testing at various frequencies materials required in the manufacture of solid tantalum 2. 1 KHz DF capacitors. In worst-case combinations, individual 3. Tightened DC leakage, Capacitance and Dissipation capacitors will exhibit sensitivity to temperature excur- Factor limits. sions. Consequently, all GR500 Series capacitors undergo ten temperature cycles between -65°C and

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 3 GR500/T210

DETAIL SPECIFICATION GR500/T210 Capacitors CAPACITOR OUTLINE DRAWINGS

UNINSULATED INSULATED DL DL BC CASE ±0.005 ±0.031 ±0.010 ±0.031 ±0.001 SIZE ±(.13) ±(.79) ±(.25) ±(.79) ±(.03) MAX. A 0.125 0.250 0.135 0.286 0.020 0.422 (3.18) (6.35) (3.43) (7.26) (.51) (10.72) B 0.175 0.438 0.185 0.474 0.020 0.610 (4.45) (11.13) (4.70) (12.04) (.51) (15.49) C 0.279 0.650 0.289 0.686 0.025 0.822 (7.09) (16.51) (7.34) (17.42) (.64) (20.88) D 0.341 0.750 0.351 0.786 0.025 0.922 (8.66) (19.05) (8.92) (19.96) (.64) (23.42)

T210 ORDERING INFORMATION T 210 A 105 K 050 R S TANTALUM LEAD MATERIAL S—Standard SERIES (Solder coated nickel) 210—GR500/J (KEMET) High Reliability; Solid Electrolyte. Graded; High Reliability; Hermetic Seal; Axial Lead; Polar CASE SIZE GRADED FAILURE RATE A/B/C/D M—1%/k hrs. P—0.1%/k hrs. PICOFARAD CODE R—0.01%/k hrs. First two digits represent significant fig- S—0.001%/k hrs. ures. Third digit specifies number of zeros to follow. CAPACITANCE TOLERANCE VOLTAGE M— ±20% at 85°C K— ±10% J— ±5% RATINGS & PART NUMBER REFERENCE

3.9 A T210A395(1)006(2)S R,S 0.1 1.0 1.25 4.0 4.0 1.00 27.0 B T210B276(1)006(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.25 4.7 A T210A475(1)006(2)S R,S 0.1 1.0 1.25 4.0 4.0 0.90 33.0 B T210B336(1)006(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.24 5.6 A T210A565(1)006(2)S R,S 0.1 1.0 1.25 4.0 4.0 0.90 39.0 B T210B396(1)006(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.24 6.8 A T210A685(1)006(2)S R,S 0.1 1.0 1.25 4.0 6.0 0.80 47.0 B T210B476(1)006(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.24 56.0 B T210B566(1)006(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.24

(1) To complete Part Number, insert Capacitance Tolerance Symbol in 9th character, M— ±20%, K— ±10%, J— ±5%. (2) To complete Part Number, insert Failure Rate Symbol in the 13th character as shown above.

4 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500/T210

DETAIL SPECIFICATION GR500/T210 Capacitors CAPACITOR OUTLINE DRAWINGS

NOMINAL MAXIMUM MAXIMUM ESR NOMINAL MAXIMUM MAXIMUM ESR CAPACI- GRADED LEAKAGE CURRENT DISSIPATION FACTOR MAXIMUM CAPACI- GRADED LEAKAGE CURRENT DISSIPATION FACTOR MAXIMUM TANCE CASE PART NUMBER FAILURE AT RATED VOLTS (%) AT 120 Hz OHMS TANCE CASE PART NUMBER FAILURE AT RATED VOLTS (%) AT 120 Hz OHMS (µF) 25°C SIZE RATES+25°C +85°C +125°C -55° +85°C 100 kHz (µF) 25°C SIZE RATES+25°C +85°C +125°C -55° +85°C 100 kHz 120 Hz (µA) (µA) (µA) +25°C +125°C +25°C 120 Hz (µA) (µA) (µA) +25°C +125°C +25°C 6 VOLT RATING AT 85°C—4 VOLT RATING AT 125°C 20 VOLT RATING AT 85°C—13 VOLT RATING AT 125°C (CONT’D.) 82.0 C T210C826(1)006(2)S R,S 1.5 15.0 18.75 5.0 8.0 0.12 4.7 B T210B475(1)020(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.51 100.0 C T210C107(1)006(2)S R,S 1.5 15.0 18.75 5.0 8.0 0.11 5.6 B T210B565(1)020(2)S P,R 0.5 5.0 6.25 4.0 6.0 0.47 120.0 C T210C127(1)006(2)S R,S 1.5 15.0 18.75 5.0 8.0 0.10 6.8 B T210B685(1)020(2)S P,R 0.5 5.0 6.25 4.0 6.0 0.43 150.0 C T210C157(1)006(2)S R,S 1.5 15.0 18.75 5.0 8.0 0.09 8.2 B T210B825(1)020(2)S P,R 0.5 5.0 6.25 4.0 6.0 0.39 180.0 C T210C187(1)006(2)S R,S 1.5 15.0 18.75 5.0 8.0 0.08 10.0 B T210B106(1)020(2)S P,R 0.5 5.0 6.25 4.0 6.0 0.35 220.0 D T210D227(1)006(2)S R,S 2.0 20.0 25.00 6.0 8.0 0.07 12.0 B T210B126(1)020(2)S P,R 0.5 5.0 6.25 4.0 6.0 0.32 270.0 D T210D277(1)006(2)S R,S 2.0 20.0 25.00 6.0 8.0 0.07 15.0 B T210B156(1)020(2)S P,R 0.5 5.0 6.25 4.0 6.0 0.29 330.0 D T210D337(1)006(2)S R,S 3.0 30.0 39.50 6.0 8.0 0.06 18.0 C T210C186(1)020(2)S R,S 1.0 10.0 12.50 4.0 6.0 0.25 10 VOLT RATING AT 85°C—7 VOLT RATING AT 125°C 22.0 C T210C226(1)020(2)S R,S 1.0 10.0 12.50 4.0 6.0 0.25 27.0 C T210C276(1)020(2)S P,R 1.5 15.0 18.75 4.0 6.0 0.21 2.7 A T210A275(1)010(2)S R,S 0.1 1.0 1.25 4.0 4.0 1.20 33.0 C T210C336(1)020(2)S P,R 1.5 15.0 18.75 4.0 6.0 0.19 3.3 A T210A335(1)010(2)S R,S 0.1 1.0 1.25 4.0 4.0 1.00 39.0 C T210C396(1)020(2)S P,R 1.5 15.0 18.75 4.0 6.0 0.17 3.9 A T210A395(1)010(2)S R,S 0.1 1.0 1.25 4.0 4.0 1.00 47.0 C T210C476(1)020(2)S P,R 1.5 15.0 18.75 4.0 6.0 0.16 4.7 A T210A475(1)010(2)S R,S 0.1 1.0 1.25 4.0 4.0 0.90 56.0 D T210D566(1)020(2)S M,P 2.0 20.0 25.00 4.0 6.0 0.13 12.0 B T210B126(1)010(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.32 68.0 D T210D686(1)020(2)S M,P 2.0 20.0 25.00 4.0 6.0 0.12 15.0 B T210B156(1)010(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.29 82.0 D T210D826(1)020(2)S M,P 3.0 30.0 37.50 4.0 6.0 0.11 18.0 B T210B186(1)010(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.27 100.0 D T210D107(1)020(2)S M,P 3.0 30.0 37.50 4.0 6.0 0.10 22.0 B T210B226(1)010(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.26 27.0 B T210B276(1)010(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.25 35 VOLT RATING AT 85°C—23 VOLT RATING AT 125°C 33.0 B T210B336(1)010(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.24 0.82 A T210A824(1)035(2)S R,S 0.1 1.0 1.25 2.0 4.0 1.60 39.0 B T210B396(1)010(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.24 1.0 A T210A105(1)035(2)S R,S 0.1 1.0 1.25 2.0 4.0 1.40 47.0 C T210C476(1)010(2)S R,S 1.5 15.0 18.75 5.0 6.0 0.16 2.7 B T210B275(1)035(2)S R,S 0.25 2.5 3.13 3.0 4.0 0.68 56.0 C T210C566(1)010(2)S R,S 1.5 15.0 18.75 5.0 6.0 0.15 3.3 B T210B335(1)035(2)S R,S 0.5 5.0 6.25 3.0 4.0 0.62 68.0 C T210C686(1)010(2)S R,S 1.5 15.0 18.75 5.0 6.0 0.13 3.9 B T210B395(1)035(2)S R,S 0.5 5.0 6.25 3.0 4.0 0.56 82.0 C T210C826(1)010(2)S R,S 1.5 15.0 18.75 5.0 6.0 0.12 4.7 B T210B475(1)035(2)S R,S 0.5 5.0 6.25 3.0 4.0 0.51 100.0 C T210C107(1)010(2)S R,S 1.5 15.0 18.75 5.0 8.0 0.11 5.6 B T210B565(1)035(2)S M,P 0.5 5.0 6.25 3.0 4.0 0.47 120.0 C T210C127(1)010(2)S R,S 1.5 15.0 18.75 5.0 8.0 0.10 6.8 B T210B685(1)035(2)S M,P 0.5 5.0 6.25 3.0 4.0 0.43 150.0 D T210D157(1)010(2)S R,S 2.0 20.0 25.00 5.0 8.0 0.09 8.2 C T210C825(1)035(2)S R,S 1.0 10.0 12.50 3.0 5.0 0.36 180.0 D T210D187(1)010(2)S R,S 2.0 20.0 25.00 5.0 8.0 0.08 10.0 C T210C106(1)035(2)S R,S 1.0 10.0 12.50 3.0 5.0 0.33 220.0 D T210D227(1)010(2)S R,S 3.0 30.0 37.50 5.0 8.0 0.07 12.0 C T210C126(1)035(2)S P,R 1.0 10.0 12.50 3.0 5.0 0.30 15 VOLT RATING AT 85°C—10 VOLT RATING AT 125°C 15.0 C T210C156(1)035(2)S P,R 1.0 10.0 12.50 3.0 5.0 0.27 18.0 C T210C186(1)035(2)S P,R 1.0 10.0 12.50 3.0 5.0 0.25 1.2 A T210A125(1)015(2)S R,S 0.25 2.5 3.13 3.0 4.0 1.40 22.0 C T210C226(1)035(2)S M,P 1.0 10.0 12.50 3.0 5.0 0.25 1.5 A T210A155(1)015(2)S R,S 0.25 2.5 3.13 3.0 4.0 1.30 27.0 D T210D276(1)035(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.18 1.8 A T210A185(1)015(2)S R,S 0.25 2.5 3.13 3.0 4.0 1.25 33.0 D T210D336(1)035(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.17 2.2 A T210A225(1)015(2)S R,S 0.25 2.5 3.13 3.0 4.0 1.20 39.0 D T210D396(1)035(2)S M,P 2.0 20.0 25.00 4.0 6.0 0.15 2.7 A T210A275(1)015(2)S P,R 0.25 2.5 3.13 3.0 4.0 1.20 47.0 D T210D476(1)035(2)S M,P 3.0 30.0 37.50 4.0 6.0 0.14 3.3 A T210A335(1)015(2)S P,R 0.25 2.5 3.13 3.0 4.0 1.00 5.6 B T210B565(1)015(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.47 50 VOLT RATING AT 85°C—33 VOLT RATING AT 125°C 6.8 B T210B685(1)015(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.43 0.0047 A T210A472(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 30.00 8.2 B T210B825(1)015(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.39 0.0056 A T210A562(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 28.00 10.0 B T210B106(1)015(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.35 0.0068 A T210A682(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 26.00 12.0 B T210B126(1)015(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.32 0.0082 A T210A822(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 24.00 15.0 B T210B156(1)015(2)S R,S 0.5 5.0 6.25 4.0 6.0 0.29 0.01 A T210A103(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 22.00 18.0 B T210B186(1)015(2)S P,R 0.5 5.0 6.25 4.0 6.0 0.27 0.012 A T210A123(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 20.00 22.0 B T210B226(1)015(2)S P,R 0.5 5.0 6.25 4.0 6.0 0.26 0.015 A T210A153(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 18.00 27.0 C T210C276(1)015(2)S R,S 1.5 15.0 18.75 4.0 6.0 0.21 0.018 A T210A183(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 16.00 33.0 C T210C336(1)015(2)S R,S 1.5 15.0 18.75 4.0 6.0 0.19 0.022 A T210A223(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 14.00 39.0 C T210C396(1)015(2)S P,R 1.5 15.0 18.75 4.0 6.0 0.17 0.027 A T210A273(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 13.00 47.0 C T210C476(1)015(2)S P,R 1.5 15.0 18.75 4.0 6.0 0.16 0.033 A T210A333(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 12.00 56.0 C T210C566(1)015(2)S P,R 1.5 15.0 18.75 4.0 6.0 0.15 0.039 A T210A393(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 11.00 68.0 C T210C686(1)015(2)S P,R 1.5 15.0 18.75 4.0 6.0 0.13 0.047 A T210A473(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 10.00 82.0 D T210D826(1)015(2)S P,R 2.0 20.0 25.00 5.0 8.0 0.11 0.056 A T210A563(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 9.00 100.0 D T210D107(1)015(2)S P,R 2.0 20.0 25.00 5.0 8.0 0.10 0.068 A T210A683(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 8.00 120.0 D T210D127(1)015(2)S P,R 2.0 20.0 25.00 5.0 8.0 0.09 0.082 A T210A823(1)050(2)S R,S 0.05 0.5 .63 2.0 4.0 7.50 150.0 D T210D157(1)015(2)S P,R 3.0 30.0 37.50 5.0 8.0 0.09 0.1 A T210A104(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 7.00 20 VOLT RATING AT 85°C—13 VOLT RATING AT 125°C 0.12 A T210A124(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 6.50 0.15 A T210A154(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 5.50 1.2 A T210A12510202S P,R 0.25 2.5 3.13 3.0 4.0 1.40 0.18 A T210A184(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 5.00 1.5 A T210A15510202S P,R 0.25 2.5 3.13 3.0 4.0 1.30 0.22 A T210A224(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 4.00 1.8 A T210A18510202S P,R 0.25 2.5 3.13 3.0 4.0 1.25 0.27 A T210A274(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 3.50 2.2 A T210A22510202S P,R 0.25 2.5 3.13 3.0 4.0 1.20 0.33 A T210A334(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 3.30 (1) (2) (1) To complete Part Number, insert Capacitance Tolerance Symbol in 9th character, M— 0.39 A T210A394 050 S R,S 0.1 1.0 1.25 2.0 4.0 3.30 ±20%, K— ±10%, J— ±5%. 0.47 A T210A474(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 3.00 (2) To complete Part Number, insert Failure Rate Symbol in the 13th character as shown 0.56 A T210A564(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 2.50 on page 4. KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 5 GR500/T210

DETAIL SPECIFICATION GR500/T210 Capacitors

NOMINAL MAXIMUM MAXIMUM ESR NOMINAL MAXIMUM MAXIMUM ESR CAPACI- GRADED LEAKAGE CURRENT DISSIPATION FACTOR MAXIMUM CAPACI- GRADED LEAKAGE CURRENT DISSIPATION FACTOR MAXIMUM TANCE CASE PART NUMBER FAILURE AT RATED VOLTS (%) AT 120 Hz OHMS TANCE CASE PART NUMBER FAILURE AT RATED VOLTS (%) AT 120 Hz OHMS (µF) 25°C SIZE RATES+25°C +85°C +125°C -55° +85°C 100 kHz (µF) 25°C SIZE RATES+25°C +85°C +125°C -55° +85°C 100 kHz 120 Hz (µA) (µA) (µA) +25°C +125°C +25°C 120 Hz (µA) (µA) (µA) +25°C +125°C +25°C 50 VOLT RATING AT 85°C—33 VOLT RATING AT 125°C (CONT’D.) 75 VOLT RATING AT 85°C—50 VOLT RATING AT 125°C (CONT’D.) 0.68 A T210A684(1)050(2)S R,S 0.1 1.0 1.25 2.0 4.0 1.80 1.8 B T210B185(1)075(2)S P,R 0.5 5.0 6.25 2.0 4.0 0.92 0.82 A T210A824(1)050(2)S P,R 0.1 1.0 1.25 2.0 4.0 1.60 2.2 B T210B225(1)075(2)S P,R 0.5 5.0 6.25 2.0 4.0 0.80 1.0 A T210A105(1)050(2)S P,R 0.1 1.0 1.25 2.0 4.0 1.40 2.7 B T210B275(1)075(2)S M,P 0.5 5.0 6.25 2.0 4.0 0.68 1.2 B T210B125(1)050(2)S R,S 0.25 2.5 3.13 2.0 4.0 1.20 3.3 B T210B335(1)075(2)S M,P 0.75 7.5 9.40 2.0 4.0 0.62 1.5 B T210B155(1)050(2)S R,S 0.25 2.5 3.13 2.0 4.0 1.10 3.9 B T210B395(1)075(2)S M,P 0.75 7.5 9.40 2.0 4.0 0.56 1.8 B T210B185(1)050(2)S R,S 0.25 2.5 3.13 2.0 4.0 0.92 4.7 C T210C475(1)075(2)S P,R 1.5 15.0 18.75 3.0 4.0 0.47 2.2 B T210B225(1)050(2)S R,S 0.25 2.5 3.13 2.0 4.0 0.80 5.6 C T210C565(1)075(2)S P,R 1.5 15.0 18.75 3.0 4.0 0.44 2.7 B T210B275(1)050(2)S P,R 0.25 2.5 3.13 2.0 4.0 0.68 6.8 C T210C685(1)075(2)S M,P 2.0 20.0 25.00 3.0 4.0 0.44 3.3 B T210B335(1)050(2)S P,R 0.5 5.0 6.25 2.0 4.0 0.62 8.2 C T210C825(1)075(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.36 3.9 B T210B395(1)050(2)S P,R 0.5 5.0 6.25 2.0 4.0 0.56 10.0 C T210C106(1)075(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.33 4.7 B T210B475(1)050(2)S M,P 0.5 5.0 6.25 2.0 4.0 0.51 12.0 D T210D126(1)075(2)S M,P 2.5 25.0 31.25 3.0 5.0 0.26 5.6 C T210C565(1)050(2)S P,R 1.5 15.0 18.75 3.0 4.0 0.44 15.0 D T210D156(1)075(2)S M,P 2.5 25.0 31.25 3.0 5.0 0.23 6.8 C T210C685(1)050(2)S P,R 1.5 15.0 18.75 3.0 5.0 0.40 100 VOLT RATING AT 85°C—67 VOLT RATING AT 125°C 8.2 C T210C825(1)050(2)S P,R 1.5 15.0 18.75 3.0 5.0 0.36 0.0047 A T210A472(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 30.00 10.0 C T210C106(1)050(2)S P,R 1.5 15.0 18.75 3.0 5.0 0.33 0.0056 A T210A562(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 28.00 12.0 C T210C126(1)050(2)S M,P 1.5 15.0 18.75 3.0 5.0 0.30 0.0068 A T210A682(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 26.00 15.0 C T210C156(1)050(2)S M,P 1.5 15.0 18.75 3.0 5.0 0.27 0.0082 A T210A822(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 24.00 18.0 C T210C186(1)050(2)S M,P 1.5 15.0 18.75 3.0 5.0 0.25 0.01 A T210A103(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 22.00 22.0 D T210D226(1)050(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.20 0.012 A T210A123(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 20.00 75 VOLT RATING AT 85°C—50 VOLT RATING AT 125°C 0.015 A T210A153(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 18.00 0.0047 A T210A472(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 30.00 0.018 A T210A183(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 16.00 0.0056 A T210A562(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 28.00 0.022 A T210A223(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 14.00 0.0068 A T210A682(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 26.00 0.027 A T210A273(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 13.00 0.0082 A T210A822(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 24.00 0.033 A T210A333(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 12.00 0.01 A T210A103(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 22.00 0.039 A T210A393(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 11.00 0.012 A T210A123(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 20.00 0.047 A T210A473(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 10.00 0.015 A T210A153(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 18.00 0.056 A T210A563(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 9.00 0.018 A T210A183(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 16.00 0.068 A T210A683(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 8.00 0.022 A T210A223(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 14.00 0.082 A T210A823(1)100(2)S M,P 0.1 1.0 1.25 2.0 4.0 7.50 0.027 A T210A273(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 13.00 0.1 A T210A104(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 7.00 0.033 A T210A333(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 12.00 0.12 A T210A124(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 6.50 0.039 A T210A393(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 11.00 0.15 A T210A154(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 4.40 0.047 A T210A473(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 10.00 0.18 A T210A184(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 4.00 0.056 A T210A563(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 9.00 0.22 A T210A224(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 3.50 0.068 A T210A683(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 8.00 0.27 A T2l0A274(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 3.10 0.082 A T210A823(1)075(2)S P,R 0.1 1.0 1.25 2.0 4.0 7.50 0.33 A T210A334(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 2.80 0.1 A T210A104(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 7.00 0.39 A T210A394(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 2.60 0.12 A T210A124(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 6.50 0.47 A T210A474(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 2.40 0.15 A T210A154(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 4.40 0.56 A T210A564(1)100(2)S M.P 0.25 2.5 3.13 2.0 4.0 2.25 0.18 A T210A184(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 4.00 0.68 B T210B684(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 2.10 0.22 A T210A224(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 3.50 0.82 B T210B824(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 1.47 0.27 A T210A274(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 3.10 1.0 B T210B105(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 1.40 0.33 A T310A334(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 2.80 1.2 B T210B125(1)100(2)S M,P 0.25 2.5 3.13 2.0 4.0 1.33 0.39 A T310A394(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 2.60 1.5 B T210B155(1)100(2)S M,P 0.5 5.0 6.25 2.0 4.0 1.06 0.47 A T210A474(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 2.40 1.8 B T210B185(1)100(2)S M,P 0.5 5.0 6.25 2.0 4.0 0.92 0.56 A T210A564(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 2.25 2.2 B T210B225(1)100(2)S M,P 0.5 5.0 6.25 2.0 4.0 0.80 0.68 A T210A684(1)075(2)S M,P 0.25 2.5 3.13 2.0 4.0 2.10 2.7 B T210B275(1)100(2)S M,P 0.5 5.0 6.25 2.0 4.0 0.68 0.82 B T210B824(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 1.47 3.3 C T210C335(1)100(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.62 1.0 B T210B105(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 1.40 3.9 C T210C395(1)100(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.56 1.2 B T210B125(1)075(2)S P,R 0.25 2.5 3.13 2.0 4.0 1.33 4.7 C T210C475(1)100(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.47 1.5 B T210B155(1)075(2)S P,R 0.5 5.0 6.25 2.0 4.0 1.06 5.6 C T210C565(1)100(2)S M,P 2.0 20.0 25.00 3.0 5.0 0.44 6.8 C T210C685(1)100(2)S M 2.0 20.0 25.00 3.0 5.0 0.40 (1) To complete Part Number, insert Capacitance Tolerance Symbol in 9th character, M— ±20%, K— ±10%, J— ±5%. 8.2 D T210D825(1)100(2)S M 2.5 25.0 31.25 3.0 5.0 0.36 (2) To complete Part Number, insert Failure Rate Symbol in the 13th character as shown 10.0 D T210D106(1)100(2)S M 2.5 25.0 31.25 3.0 5.0 0.33 on page 4. CAPACITOR MARKINGS A Case B Case C Case

+T210 —Polarity symbol, series designation +KT210B —Polarity symbol, KEMET part number +KEMET —Polarity symbol, KEMET K10%S —KEMET tolerance, failure rate 475K050 —KEMET part number (continued) T210C106K—KEMET part number R68 µF —Capacitance SS4R7 µF —KEMET part number (continued) 035SS 10% —KEMET part number (continued), 50 V —Voltage capacitance tolerance 725XA —Date Code (Year and week of 50 V 10% —Voltage, tolerance 10 µF 35V —Capacitance, voltage manufacture and batch designator) 0725XA —Date Code (Year and week of 0725XA —Date Code (Year and week of manufacture and batch designator) manufacture and batch designator)

6 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500/T210

APPLICATIONS INFORMATION GR500/T210 Introduction — The following section is provided for assis- a measurement parameter at higher frequencies, where tance in the application of T210 Series capacitors. Space impedance and ESR are the normal parameters of concern. . does not permit a complete discussion of all technical F TYPICAL DISSIPATION FACTOR AS A aspects, and further information on specific problems may . FUNCTION OF FREQUENCY AT be obtained through KEMET sales representatives. D + 25° C

z POLAR CAPACITORS - T210 SERIES H Capacitance — The nominal values listed in Table 1 con- 20.0 forms to accepted industry practice; intermediate values may 0 2

be produced on special order. Standard tolerances are 1

f 10.0 ± 20%,z ± 10%, and ± 5%. Closer tolerances of ±2% may be o H available upon special order and after agreement upon mea- r e 0 surement conditions. i e l 2 c The capacitance of solid tantalum capacitors decreases p i t 1 n with frequency as shown in Figure 1. The nominal values of l u f Table 1a are also available at 1 kHz on special order. Typical t o i variation of capacitance with respect to temperature is illus- M c trated r in Figure 2. 1.0 a e 100 1K 10K i l p Frequency - Hertz 1.0 p a i Figure 3. Normal EffectFig 3 Frequency of Frequency –Hertz upon t l C Reference Dissipation Factor 1.0 at 120Hz u 0.9

M 100 1K 10K DC Leakage Current — The DC Leakage current limits of Frequency - Hertz

e Table I are the lowest generally specified in the solid tanta- Figure 1. Normal Effect of Frequency upon Capacitance u Fig 1 Capacitance Versus Frequency

l lum industry. Even lower leakage currents are available on

a special order. Low leakage current, aside from its intrinsic V value, is an indication of anode quality. DC leakage current e as a function of temperature is represented by the typical c +20

n curve in Figure 4, while similar information pertaining to

a +10

t leakage behavior with respect to voltage is contained in i

c Figure 5. 0 a

p -10 a

C -20 10.0

-80 -60 -40 -20 0 +20 +40 +60 +80 +100 +120

Operating Temperature °C t n e r Figure 2. TypicalFig 2Effect Capacitance of Temperature Versus Temperature upon Capacitance r u C

Dissipation Factor — Dissipation factor is defined as the e Reference 1.0 g at + 25 °C a

ratio of equivalent series resistance to capacitive reactance at k a a specified frequency: e L

R C 1.0 D = = 2πfCR D f

XC o r e i l p

Where R = equivalent series resistance in ohms i t l

D = dissipation factor u M

XC = capacitive reactance in ohms C = series capacitance in farads f = frequency in Hertz

Unless otherwise stated, a standard frequency of 120 Hz is 0.1 used for both dissipation and capacitance measurements. -60 -40 -20 0 +20 +40 +60 +80 +100 +125 Typical behavior of dissipation factor with frequency is Operating Temperature –˚C shown in Figure 3. Dissipation factor loses its importance as Fig 4 Typical Variation of leakage current with temperature.

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 7 GR500/T210

APPLICATIONS INFORMATION GR500/T210 (Continued) Expected reliability factors for voltages and temperatures t n

e 1.0 other than the rated conditions may be found in Figure 6. r r

u Since T210 Series capacitors are supplied with a predeter- C

e mined failure rate under rated conditions, reliability under g a

k use conditions may be estimated with this nomograph. a

e 0.1 L

C Circuit Impedance — Failure rates are affected by temper- D f

o ature and voltage as described in Figure 6 and also by the r e

i circuit impedance seen by the capacitor. Originally, applica- l p i

t 0.01 tion advice for solid tantalum capacitors suggested an l u impedance of 3 ohms or higher per applied volt. This advice M was later found to be unnecessarily conservative, and the factors below are based on 0.1 ohm per volt as the unity fail- 0.001 ure rate multiplier. 0 10 20 30 40 50 60 70 80 90 100 110 Percentage of Rated Voltage Circuit Impedance, Failure Rate Fig 5 Typical variation of leakage current with voltage Ohms per Volt Multiplying Factor 0.1 1.0 0.2 0.8 Voltage and Temperature Ratings; Reliability Effect — 0.4 0.6 T210 Series capacitors are manufactured in 6 through 100 0.6 0.4 volt ratings at 85°C. Operation at 125°C with 2/3 rated volt- 0.8 0.3 age applied gives equivalent results and voltage may be der- 1 0.2 ated linearly between these two points. Solid tantalum 2 0.1 capacitors may be operated continuously at any voltage from ≥3 0.07 zero to the maximum rating without adverse effects. Operation at voltage below nameplate improves reliability, Equivalent Series Resistance — The equivalent series while subsequent operation at a higher voltage will not be resistance (ESR) of a solid tantalum capacitor is frequency affected by prior low voltage use. dependent as shown in Figure 7a thru 7g. The curves are typical of the capacitor values noted, with measurements being 125 1.2 1 made by contacting lead wires /4 inch from the ends of the 103 120 capacitor cases. Since ESR decreases with frequency, AC 1.1 performance at higher frequencies is considerably better 102 110 than would be predicted from the 120 Hz ratings. 85°C 1.0 101 Rating T3 Capacitor Impedance — The relationship between imped- 100 ance and frequency at various voltage ratings is illustrated 1.0 0.9 F3 V2 with typical curves in Figure 7. Impedance declines with T1 F1 V1 s

u 90 decreasing capacitive reactance, but ESR becomes dominant i -1

s F V 10 l 2 3 0.8 e before the self-resonant point is reached, producing the typ-

C 85 F , s r V e e T2 ical, damped curves. Finally, impedance increases as induc- -2 i e 10 l o r 80 i p t i

g 0.7 t a l e 125°C tance of the lead wire and other capacitor elements domi- u R

D 0.67 - M Rating e e nates. Obviously, high frequency impedance is directly g r Connect the temperature and -3 10 e t a u t t a applied voltage ratio of l

a 70 0.6 influencedo by the length of lead wire and general mounting r interest with a straight edge. R V e e

p 1 r The multiplier of failure rate is d 4 u configuration. The typical curves of Figure 7 include / inch e

m -4 l i

10 i l

e given at the intersection of this a p T F line with the model scale. ofp lead wire at each end of the capacitor.

g 0.5

60 A n i t

a -5

r 10 e

p Given T1 & V1 Read Failure AC Ripple — Permissable AC ripple voltage is related to O Rate Multiplier F1 0.4 50 Given T, & F2 10-6 the rated voltage, the ESR of the capacitor, and the power Read Reguired Voltage V2 Given F3 & V3 dissipation capability of a particular case size: Read Allowable Temp T3 0.3 1. The positive peak AC voltage plus the DC bias 40 10-7 voltage (if any), must not exceed the rated voltage. 0.2 10-8 2. The negative peak AC voltage, in combination 30 with the bias voltage (if any), must not exceed that

25 0.1 allowable for a polar T210 capacitor (see Table T F V III). Figure 12.Fig 6 Reliability Reliability alignment Nomograph chart 8 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300

B GR500/T210

APPLICATIONS INFORMATION GR500/T210 (Continued)

10VDC Rated

100 Impedance ESR (Ohms)

3 10 3 1 µ 0 F 0 d 2 µ 2 F 0 d µ F 1 d 3 3 µFd 100 µFd 0.1 220 µFd

1001000 10K 100K 1M 10M Frequency (MHz) Figure 7a. ESR and Impedance vs. Frequency

20VDC Rated 30 Impedance ESR 4 10 7 (Ohms) µ 6 F 8 d µ 3 1 F 0 d 0 µ F 1 d 47 µF 0.3 d 68 µFd 0.1 100 µFd

1001000 10K 100K 1M 10M Frequency (MHz) Figure 7b. ESR and Impedance vs. Frequency

35VDC Rated Impedance 100 2 ESR .7 µ (Ohms) F 4 d .7 µ F 10 2 d 2 4 µ 7 F µ d 2 F .7 d µF 1 4 d .7 µ Fd 47 µFd 0.1 22 µFd

1001000 10K 100K 1M 10M Frequency (MHz) Figure 7c. ESR and Impedance vs. Frequency

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 9 GR500/T210

APPLICATIONS INFORMATION GR500/T210 (Continued)

3. The power dissipated in the equivalent series Reverse Voltage — The solid tantalum capacitor is basi- resistance of the capacitor must not exceed the cally a polar device and can be damaged by serious reversals limits specified in Table II. of polarity even for short periods of time, depending upon The power dissipated may be calculated from the the circuit impedance. However, some short duration rever- following: sal is permissable as shown in Table III. 2 P= E R 2 Z Where E = ripple voltage across capacitor in rms volts TABLE III Z = capacitor impedance in ohms at the specified fre- Permissible Reverse Voltage quency (typical values from Figure 7) Temp. % of Forward R = equivalent series resistance in ohms (typical val- °C Rated Voltage ues from Figure 7) 25 15 85 5 Ripple voltage, as limited by power dissipation, may be 125 1 determined as follows:

E max (25°C) = Z P max Shelf Life — Shelf life is particularly difficult to define for R the solid tantalum capacitor. Extended periods of storage at high temperature will cause some small change in leakage Where P max=maximum permissible power from current which usually returns to normal upon short time Table III application of working voltage. Storage at low temperatures R = ESR from Figure 7 causes little or no degradation of leakage current. Long-term E max (85°C) = 0.9 E max (25°C) studies of capacitance and dissipation factor shift for as long E max (125°C) = 0.4 E max (25°C) as 45,000 hours indicate only minor variations (usually less than 2%) in these parameters. TABLE II Installation — Mounting procedures should not place Maximum Permissible Power Dissipation at 25°C Ambient undue strain on terminals, particularly the positive end with T210 Polar Capacitors its glass-metal seal. Attention to soldering technique should Case Size Watts avoid excessive heat transfer which might remelt the capac- A 0.090 itor’s internal solder and cause loss of hermeticity or short B 0.100 circuits. Potting materials should not produce excessive cur- C 0.125 D 0.180 ing exotherms or shrinkage pressures.

10 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500/T220

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 11 GR500/T220

12 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500/T220

0712XM

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 13 GR500/T220

14 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500/T220

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 15 GR500/T220

16 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500/T240

DETAIL SPECIFICATION GR500/T240 Capacitors CAPACITOR OUTLINE DRAWINGS

DIMENSIONS — INCHES & (MILLIMETERS) UNINSULATED INSULATED DL DL BC CASE ±0.005 ±0.031 ±0.010 ±0.031 ±0.001 SIZE ±(.13) ±(.79) ±(.25) ±(.79) ±(.03) MAX. A 0.125 (3.18) 0.250 (6.35) 0.135 (3.43) 0.286 (7.26) 0.020 (.51) 0.422 (10.72) B 0.175 (4.45) 0.438 (11.13) 0.185 (4.70) 0.474 (12.04) 0.020 (.51) 0.610 (15.49) C 0.279 (7.09) 0.650 (16.51) 0.289 (7.34) 0.686 (17.42) 0.025 (.64) 0.822 (20.88) D 0.341 (8.66) 0.750 (19.05) 0.351 (8.92) 0.786 (19.96) 0.025 (.64) 0.922 (23.42)

T240 ORDERING INFORMATION T 240 A 125 K 050 R S TANTALUM LEAD MATERIAL S—Standard SERIES (Solder coated nickel) 240—GR500/J (KEMET) High Reliability; Solid Electrolyte. Graded; High Reliability; Hermetic Seal; Axial Lead; Polar CASE SIZE GRADED FAILURE RATE A/B/C/D M—1%/k hrs. P—0.1%/k hrs. PICOFARAD CODE R—0.01%/k hrs. First two digits represent significant fig- ures. Third digit specifies number of zeros to follow. CAPACITANCE TOLERANCE VOLTAGE M— ±20% at 85°C K— ±10% J— ±5%

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 17 GR500/T240

DETAIL SPECIFICATION GR500/T240 Capacitors RATINGS & PART NUMBER REFERENCE

NOMINAL MAXIMUM MAXIMUM ESR NOMINAL MAXIMUM MAXIMUM ESR CAPACI- GRADED LEAKAGE CURRENT DISSIPATION FACTOR MAXIMUM CAPACI- GRADED LEAKAGE CURRENT DISSIPATION FACTOR MAXIMUM TANCE CASE PART NUMBER FAILURE AT RATED VOLTS (%) AT 120 Hz OHMS TANCE CASE PART NUMBER FAILURE AT RATED VOLTS (%) AT 120 Hz OHMS (µF) 25°C SIZE RATES+25°C +85°C +125°C -55° +85°C 100 kHz (µF) 25°C SIZE RATES+25°C +85°C +125°C -55° +85°C 100 kHz 120 Hz (µA) (µA) (µA) +25°C +125°C +25°C 120 Hz (µA) (µA) (µA) +25°C +125°C +25°C 6 VOLT RATING AT 85°C—4 VOLT RATING AT 125°C 30 VOLT RATING AT 85°C—20 VOLT RATING AT 125°C 10.0 A T240A106(1)006(2)S P,R 0.5 2.0 6.25 5.0 6.0 0.700 1.8 A T240A185(1)030(2)S P,R 0.5 2.0 6.25 3.0 4.0 1.25 12.0 A T240A126(1)006(2)S P,R 0.5 2.0 6.25 5.0 6.0 0.600 2.2 A T240A225(1)030(2)S M,P 0.5 2.0 6.25 3.0 4.0 1.20 100.0 B T240B107(1)006(2)S P,R 1.0 3.0 12.50 6.0 8.0 0.200 2.7 A T240A275(1)030(2)S M,P 0.5 2.0 6.25 3.0 4.0 1.10 220.0 C T240C227(1)006(2)S P,R 2.0 8.0 25.00 6.0 8.0 0.090 12.0 B T240B126(1)030(2)S M,P 1.0 5.0 12.50 4.0 6.0 0.32 270.0 C T240C277(1)006(2)S P,R 2.0 8.0 25.00 6.0 8.0 0.070 15.0 B T240B156(1)030(2)S M,P 1.0 5.0 12.50 4.0 6.0 0.29 330.0 C T240C337(1)006(2)S P,R 2.0 8.0 25.00 6.0 8.0 0.065 18.0 B T240B186(1)030(2)S M,P 1.0 5.0 12.50 4.0 6.0 0.27 390.0 C T240C397(1)006(2)S P,R 2.0 8.0 25.00 8.0 10.0 0.065 56.0 C T240C566(1)030(2)S M,P 1.0 5.0 12.50 4.0 6.0 0.15 470.0 C T240C477(1)006(2)S P,R 2.0 8.0 25.00 8.0 10.0 0.060 68.0 C T240C686(1)030(2)S M,P 2.0 15.0 25.00 4.0 6.0 0.13 680.0 D T240D687(1)006(2)S P,R 5.0 10.0 62.50 8.0 10.0 0.060 82.0 D T240D826(1)030(2)S M 2.5 20.0 31.25 5.0 6.0 0.11 820.0 D T240D827(1)006(2)S P,R 5.0 10.0 62.50 8.0 10.0 0.055 100.0 D T240D107(1)030(2)S M 2.5 20.0 31.25 5.0 6.0 0.10 1000.0 D T240D108(1)006(2)S P,R 5.0 10.0 62.50 8.0 10.0 0.050 35 VOLT RATING AT 85°C—20 VOLT RATING AT 125°C 10 VOLT RATING AT 85°C—7 VOLT RATING AT 125°C 1.2 A T240A125(1)035(2)S P.R 0.5 2.0 6.25 3.0 4.0 1.30 6.8 A T240A685(1)010(2)S P,R 0.5 2.0 6.25 4.0 6.0 0.80 1.5 A T240A155(1)035(2)S P.R 0.5 2.0 6.25 3.0 4.0 1.20 8.2 A T240A825(1)010(2)S P,R 0.5 2.0 6.25 4.0 6.0 0.70 1.8 A T240A185(1)035(2)S M P 0.5 2.0 6.25 3.0 4.0 1.20 47.0 B T240B476(1)010(2)S P,R 1.0 2.0 6.25 5.0 6.0 0.22 8.2 B T240B825(1)035(2)S M,P 1.0 2.0 12.50 4.0 6.0 0.40 56.0 B T240B566(1)010(2)S P,R 1.0 4.0 12.50 5.0 6.0 0.20 10.0 B T240B106(1)035(2)S M,P 1.0 2.0 12.50 4.0 6.0 0.35 68.0 B T240B686(1)010(2)S P,R 1.0 4.0 12.50 5.0 6.0 0.18 27.0 C T240C276(1)035(2)S M,P 1.0 5.0 12.50 5.0 6.0 0.19 82.0 B T240B826(1)010(2)S P,R 1.0 4.0 12.50 5.0 6.0 0.15 33.0 C T240C336(1)035(2)S M,P 1.0 5.0 12.50 5.0 6.0 0.19 150.0 C T240C157(1)010(2)S P,R 1.0 7.0 12.50 6.0 8.0 0.10 39.0 C T240C396(1)035(2)S M P 1.0 5.0 12.50 5.0 6.0 0.17 180.0 C T240C187(1)010(2)S P,R 1.0 7.0 12.50 6.0 8.0 0.090 47.0 C T240C476(1)035(2)S M,P 1.0 5.0 12.50 5.0 6.0 0.15 220.0 C T240C227(1)010(2)S P,R 1.0 7.0 12.50 6.0 8.0 0.090 56.0 D T240D566(1)035(2)S M 2.0 10.0 25.00 5.0 6.0 0.13 270.0 C T240C277(1)010(2)S P,R 2.0 10.0 25.00 6.0 8.0 0.075 68.0 D T240D686(1)035(2)S M 2.0 10.0 25.00 5.0 6.0 0.12 330.0 D T240D337(1)010(2)S P,R 2.0 16.0 25.00 8.0 10.0 0.070 50 VOLT RATING AT 85°C—33 VOLT RATING AT 125°C 390.0 D T240D397(1)010(2)S P,R 2.0 16.0 25.00 8.0 10.0 0.070 (1) (2) 470.0 D T240D477(1)010(2)S P,R 4.0 16.0 50.00 8.0 10.0 0.065 1.2 A T240A125 050 S M,P 0.5 2.0 6.25 3.0 4.0 1.30 (1) (2) 560.0 D T240D567(1)010(2)S P,R 4.0 16.0 50.00 8.0 10.0 0.060 1.5 A T240A155 050 S M,P 0.5 2.0 6.25 3.0 4.0 1.20 5.6 B T240B565(1)050(2)S M,P 1.0 2.0 12.50 3.0 4.0 0.47 15 VOLT RATING AT 85°C—10 VOLT RATING AT 125°C 6.8 B T240B685(1)050(2)S M,P 1.0 2.0 12.50 4.0 6.0 0.43 4.7 A T240A475(1)015(2)S P,R 0.5 2.0 6.25 3.0 4.0 0.90 22.0 C T240C226(1)050(2)S M,P 1.0 5.0 12.50 4.0 6.0 0.22 5.6 A T240A565(1)015(2)S P,R 0.5 2.0 6.25 3.0 4.0 0.80 27.0 C T240C276(1)050(2)S M 1.0 5.0 12.50 4.0 6.0 0.20 6.8 A T240A685(1)015(2)S P,R 0.5 2.0 6.25 3.0 4.0 0.70 33.0 D T240D336(1)050(2)S M 1.0 5.0 12.50 4.0 6.0 0.18 27.0 B T240B276(1)015(2)S P,R 1.0 2.0 12.50 4.0 6.0 0.28 39.0 D T240D396(1)050(2)S M 1.0 5.0 12.50 4.0 6.0 0.16 33.0 B T240B336(1)015(2)S P,R 1.0 2.0 12.50 4.0 6.0 0.24 60 VOLT RATING AT 85°C—40 VOLT RATING AT 125°C 39.0 B T240B396(1)015(2)S P,R 1.0 2.0 12.50 4.0 6.0 0.22 (1) (2) 150.0 C T240C157(1)015(2)S P,R 1.0 7.0 12.50 6.0 8.0 0.10 0.82 A T240A824 060 S M,P 0.5 2.0 6.25 3.0 4.0 1.60 (1) (2) 180.0 C T240C187(1)015(2)S P,R 2.0 10.0 25.00 6.0 8.0 0.090 1.0 A T240A105 060 S M,P 0.5 2.0 6.25 3.0 4.0 1.40 (1) (2) 220.0 D T240D227(1)015(2)S P,R 2.0 10.0 25.00 6.0 8.0 0.070 4.7 B T240B475 060 S M,P 1.0 5.0 12.50 3.0 4.0 0.51 (1) (2) 270.0 D T240D277(1)015(2)S P,R 2.0 16.0 25.00 6.0 8.0 0.065 5.6 B T240B565 060 S M,P 1.0 5.0 12.50 3.0 4.0 0.47 (1) (2) 330.0 D T240D337(1)015(2)S P,R 2.0 16.0 25.00 6.0 8.0 0.060 12.0 C T240C126 060 S M 1.0 5.0 12.50 4.0 6.0 0.27 15.0 C T240C156(1)060(2)S M 1.0 5.0 12.50 4.0 6.0 0.26 20 VOLT RATING AT 85°C—13 VOLT RATING AT 125°C 18.0 C T240C186(1)060(2)S M 1.5 10.0 18.25 4.0 6.0 0.25 2.7 A T240A275(1)020(2)S P,R 0.5 2.0 6.25 3.0 4.0 1.15 22.0 C T240C226(1)060(2)S M 1.5 10.0 18.25 4.0 6.0 0.20 3.3 A T240A335(1)020(2)S P,R 0.5 2.0 6.25 3.0 4.0 0.95 27.0 D T240D276(1)060(2)S M 2.5 20.0 31.25 5.0 6.0 0.18 3.9 A T240A395(1)020(2)S P,R 0.5 2.0 6.25 3.0 4.0 0.90 33.0 D T240D336(1)060(2)S M 2.5 20.0 31.25 5.0 6.0 0.15 18.0 B T240B186(1)020(2)S P,R 1.0 2.0 12.50 4.0 6.0 0.27 22.0 B T240B226(1)020(2)S P,R 1.0 2.0 12.50 4.0 6.0 0.26 (1) To complete Part Number, insert Capacitance Tolerance Symbol in 9th character, M— ±20%, K— ±10%, J— ±5%. 27.0 B T240B276(1)020(2)S P,R 1.0 2.0 12.50 4.0 6.0 0.24 (2) To complete Part Number, insert Failure Rate Symbol in the 13th character as 56.0 C T240C566(1)020(2)S P,R 1.0 10.0 12.50 5.0 6.0 0.15 shown. 68.0 C T240C686(1)020(2)S P,R 1.0 10.0 12.50 5.0 6.0 0.14 82.0 C T240C826(1)020(2)S P,R 1.0 10.0 12.50 5.0 6.0 0.12 100.0 C T240C107(1)020(2)S P,R 1.0 10.0 12.50 5.0 6.0 0.10 120.0 C T240C127(1)020(2)S P,R 1.0 10.0 12.50 6.0 6.0 0.090 150.0 D T240D157(1)020(2)S M,P 2.0 10.0 25.00 6.0 8.0 0.080 180.0 D T240D187(1)020(2)S M,P 2.0 10.0 25.00 6.0 8.0 0.070 CAPACITOR MARKINGS A Case B Case C Case

+T240 —Polarity symbol, series designation +KT240B —Polarity symbol, KEMET part number +KEMET —Polarity symbol, KEMET K10%R —KEMET tolerance, failure rate 106K035 —KEMET part number T240D227K —KEMET part number 1R2 µF —Capacitance* SS10 µF —KEMET part number (continued) 015PS 10% —KEMET part number (continued), 35 V —Voltage capacitance tolerance 715XA —Date Code (Year and week of 35 V 10% —Voltage, tolerance 220µF 35V —Capacitance, voltage manufacture and batch designator) 0716XB —Date Code (Year and week of 0720ZC —Date Code (Year and week of manufacture and batch designator) manufacture and batch designator) *The letter “R” incorporated in the capacitance value denotes a decimal point. 18 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500/T240

APPLICATIONS INFORMATION GR500/T240

Introduction — The following section is devoted to general shown in Figure 2. Dissipation factor loses its importance as .

information of assistance in the application of T240 Series aF measurement parameter at higher frequencies, where capacitors. Space does not permit a complete discussion of impedance. and ESR are the normal parameters of concern. all technical aspects, and further information on specific D problems may be obtained through KEMET sales represen- z H tatives. 20.0 0 2

Capacitance — The nominal values listed in Table I con- 1

f 10.0

forms to accepted industry practice; intermediate values may o

be produced on special order. Standard tolerances are r e i

± 20%, ± 10%, and ± 5%. Closer tolerances may be pro- l p

duced upon special order and after agreement upon mea- i t surement conditions. l u Typical variation of capacitance with respect to tempera- M ture is illustrated in Figure 1a. The capacitance of solid tan- 1.0

talume capacitors decreases with frequency, as shown in 100 1K 10K u

Figurel 1b. Frequency - Hertz a Figure 3. Normal Effect of Frequency upon V Fig. 2 Typical Behavior of dissipation factor as a function of DissipationFrequenc yFactor@ 25° C e

c +20 n

a +10 t DC Leakage Current — The DC Leakage current limits of z i

c 0 Table 1 for T240 Series capacitors are the lowest generally H a specified in the solid tantalum industry. Even lower leakage p 0 -10 e currents are available on special order. Low leakage current, a 2 c aside from its intrinsic value, is an indication of anode qual- C -20 1 n ity. DC leakage current as a function of temperature is rep- f a -80 -60 -40 -20 0 +20 +40 +60 +80 +100 +120 resented by the typical curve in Figure 3, while similar infor- t o i Operating Temperature °C mation pertaining to leakage behavior with respect to volt- c r age is contained in Figure 4. Figure 2. TypicalFig. 1aEffect Typical of capacitanceTemperature with upon temperature Capacitance a e i l p 1.0 p a i t l C Reference 1.0 at 120Hz

u 10.0 0.9

M 100 1K 10K t

Frequency - Hertz n e r r

Figure 1.Fig. 1b Normal Typical Effect Variation of Frequencyof capacitance upon with Capacitance frequency @ 25° C u C

e Reference 1.0

g at + 25 °C Dissipation Factor — Dissipation factor is defined as the a k a

ratio of equivalent series resistance to capacitive reactance at e L

a specified frequency: C 1.0 D f o r e

R i D = = 2πfCR l p i

XC t l u M Where R = equivalent series resistance in ohms D = dissipation factor

XC = capacitive reactance in ohms C = series capacitance in farads 0.1 f = frequency in Hertz -60 -40 -20 0 +20 +40 +60 +80 +100 +125 Operating Temperature –˚C

Unless otherwise stated, a standard frequency of 120 Hz is Fig. 3 Typical effect of temperature upon leakage current used for both dissipation and capacitance measurements. Typical behavior of dissipation factor with frequency is KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 19 GR500/T240

APPLICATIONS INFORMATION GR500/T240 (Continued)

Voltage and Temperature Ratings; Reliability Effect — Expected reliability factors for voltages and temperatures T240 Series capacitors are manufactured in 6 through 60 other than the rated conditions may be found in Figure 5. volt ratings at 85°C. Operation at 125°C with 2/3 rated volt- Since T240 Series capacitors are supplied with a predeter- age applied gives equivalent results, and voltage may be der- mined failure rate under rated conditions, reliability under ated linearly between these two points. Unlike wet elec- use conditions may be estimated with this nomograph. trolytic capacitors, solid tantalum capacitors may be operated continuously at any voltage from zero to the maximum Circuit Impedance — Failure rates are affected by temper- rating without adverse effects. Operation at voltage below ature and voltage as described in Figure 5 and also by the nameplate improves reliability, while subsequent operation circuit impedance seen by the capacitor. Traditionally, appli- at a higher voltage will not be affected by prior low voltage cation advice for solid tantalum capacitors suggested an use. impedance of 3 ohms or higher per applied volt. This advice was later found to be unnecessarily conservative, and the t

n factors in Table II, are based on 0.1 ohm per volt as the unity e 1.0 r r failure rate multiplier. u C e g a k a

e 0.1 L TABLE II C D f

o Circuit Impedance, Failure Rate r e i

l Ohms per Volt Multiplying Factor p i

t 0.01 0.1 1.0 l

u 0.2 0.8 M 0.4 0.6 0.6 0.4 0.8 0.3 0.001 0 10 20 30 40 50 60 70 80 90 100 110 1 0.2 2 0.1 Percentage of Rated Voltage ≥3 0.07 Fig. 4 Typical effect of voltage upon leakage current

125 1.2 Equivalent Series Resistance — The equivalent series 103 120 resistance (ESR) of a solid tantalum capacitor is frequency

1.1 dependent. The curves of Figure 6 are typical of the capaci- 102 110 tor values noted, with measurements being made by con- 1 85°C 1.0 4 101 Rating tacting lead wires / inch from the ends of the capacitor T3 100 cases. Since ESR decreases with frequency, AC performance 1.0 0.9 F3 V2 at higher frequencies is considerably better than would be s T1

u F1 i V1 s l 90 predicted from the 120 Hz ratings.

e -1 F2 V3 10 0.8 C F s V 85 , r e , e e i o r l T i 2 -2 t Capacitor Impedance — The relationship between imped- g 10 p i 80 a t e

l 0.7 R D u

- 125°C ance and frequency at various voltage ratings is illustrated 0.67 e M e g r Rating e a u Connect the temperature and

-3 t t t 10 l

a with typical curves in Figure 6. Impedance declines with a

applied voltage ratio of o r

70 R 0.6 V e interest with a straight edge. p e d

r decreasing capacitive reactance, but ESR becomes dominant

The multiplier of failure rate is e m u i l -4 l i e 10

given at the intersection of this p T a

p before the self-resonant point is reached, producing the typ- F

g line with the model scale.

0.5 A

n 60 i t

a -5 ical damped curves. Finally, impedance increases as induc- r 10 e p Given T1 & V1 Read Failure tance of the lead wire and other capacitor elements domi- O Rate Multiplier F1 0.4 50 Given T, & F2 10-6 nates. Obviously, high frequency impedance is directly Read Reguired Voltage V2 Given F3 & V3 influenced by the length of lead wire and general mounting Read Allowable Temp T3 0.3 10-7 1 40 configuration. The typical curves of Figure 6 include /4 inch

0.2 of lead wire at each end of the capacitor. 10-8 30

25 0.1 T F V Figure 12.Fig.5 Reliability Reliability Alignment Nomograph Chart

20 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300

B GR500/T240

APPLICATIONS INFORMATION GR500/T240 (Continued)

Where P max=maximum permissible power from Table III Z = Impedance R = ESR E max (85°C) = 0.9 E max (25°C) E max (125°C) = 0.4 E max (25°C)

TABLE III Maximum Permissible Power Dissipation at 25°C Ambient

Case Size Watts A 0.090 B 0.100 C 0.125 D 0.180

Reverse Voltage — The solid tantalum capacitor is a polar device and can be damaged by serious reversals of polarity even for short periods of time. However, some short duration reversal is permissable as shown in Table IV.

Fig. 6 Typical Behavior of Impedance and ESR as a function of frequency @ 25°C TABLE IV AC Ripple — Permissable AC ripple voltage is related to Permissible Reverse Voltage the rated voltage, the ESR of the capacitor, and the power Temp. % of Forward dissipation capability of a particular case size: °C Rated Voltage 1. The positive peak AC voltage plus the DC bias 25 15 voltage (if any), must not exceed the rated voltage. 85 5 2. The negative peak AC voltage, in combination 125 1 with the bias voltage (if any), must not exceed that allowable (see Reverse Voltage). Surge Current — Surge current testing is performed to pro- 3. The power dissipated in the equivalent series vide resistance from damage due to circuit transients. This resistance of the capacitor must not exceed the test, employing total DC circuit resistance of 1.0 max, exclu- limits specified in Table III. sive of the capacitor, is described on Page 21. The power dissipated may be calculated from the Shelf Life — Shelf life is particularly difficult to define for following: the solid tantalum capacitor. Extended periods of storage at 2 P= E R high temperature will cause some small change in leakage Z2 current which usually returns to normal upon short time application of working voltage. Storage at low temperatures Where E = ripple voltage across capacitor in rms volts causes little or no degradation of leakage current. Long-term Z = capacitor impedance in ohms at the specified fre- studies of capacitance and dissipation factor shift for as long quency. as 45,000 hours indicate only minor variations (usually less R = equivalent series resistance in ohms than 2%) in these parameters. Installation — Mounting procedures should not place Ripple voltage, as limited by power dissipation, may be undue strain on terminals, particularly the positive end with determined as follows: its glass-metal seal. Attention to soldering technique should avoid excessive heat transfer which might remelt the capacitor’s internal solder and cause loss of hermeticity or short E max (25°C) = Z P max R circuits. Potting materials should not produce excessive cur- ing exotherms or shrinkage pressures.

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 21 GR500 GRADED RELIABILITY SPECIFICATIONS GR500 KEMET Graded Reliability Specification CAPACITORS, FIXED, SOLID TANTALUM ELECTROLYTE, HIGH RELIABILITY

1. SCOPE cation. In the event of any conflict between the requirements 1.1 General Description—This specification details of this specification and the detail specification, the latter requirements for high reliability, tantalum, solid electrolyte, shall govern. hermetically sealed, fixed capacitors having a graded or determined failure rate. Operating temperature range is - 3.2 Reliability assurance—Capacitors furnished under this 65°C to +125°C with primary applications including filter- specification shall be subject to the requirements and proce- ing, bypass and coupling where the ac component of applied dures of 4.1.2, 4.4.2 and 4.5. voltage is maintained within the limits as listed in the applicable detail specification. 3.3 Material—The material shall be as specified herein. Capacitors covered by this specification are intended for However, when a specific material is not designated, a mate- use where determination of failure rate, shelf life, stability, rial shall be used which will enable the capacitors to meet leakage current and maximum resistance to environmental the performance requirement of this specification. factors are of major concern. Acceptance or the approval of any constituent material shall not be construed as a guarantee of the acceptance of the fin- 1.2 Classification—Part numbering of capacitors manufac- ished product. Material traceability shall be maintained tured in accordance with this specification is described on throughout manufacture. Pages 4 and 11. TABLE 1 — DC Rated and Surge Voltages (VDC) 2. APPLICABLE DOCUMENTS Rated Voltage Surge Voltage Rated Voltage Surge Voltage The following documents of the issue in effect form a part of 85°C 85°C 125°C 125°C 6845 this specification to the extent specified herein: 10 13 7 9 15 20 10 12 2.1 Specifications—Federal 20 26 13 16- QQ-S-571 — Solder; Tin Alloy; Lead-Tin Alloy; and 30 39 20 26 35 46 23 28 Lead Alloy 50 65 33 40 TT-I-735 — Isopropyl Alcohol 60 78 40 50 75 98 50 64 2.2 Specifications—Military 100 130 67 86 MIL-PRF-39003 — Capacitors, Fixed, Electrolytic (Solid Electrolyte) Tantalum, Established Reliability, General 3.3.1 Solder—Solder shall be as described in QQ-S-571 Specification for 3.3.2 Soldering flux—Soldering flux shall be of the rosin or 2.3 Standards—Military rosin and alcohol type. Other non-corrosive fluxes may be MIL-STD-202 — Test Methods for Electronic and used if adequate evidence indicates that no deleterious effect Electrical Components Parts. will be introduced. MIL-STD-790 — Reliability Assurance Program for Electronic Parts 3.4.1 Case—Each capacitor shall be hermetically enclosed MIL-STD-810 — Environmental Test Methods in a case which will protect the capacitor element from dete- MIL-STD-1276 — Leads, Weldable, for Electronic rioration in performance according to the environmental Component Parts conditions specified. 3. REQUIREMENTS

3.1 Detail requirements for individual capacitor series The part requirements for a capacitor series shall be as specified herein and as described in the applicable detail specifi-

22 KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 GR500 GRADED RELIABILITY SPECIFICATIONS

GR500 GRADED RELIABILITY SPECIFICATION

KEMET Electronics Corporation • P.O. Box 5928 • Greenville, S.C. 29606 • 864/963-6300 23 GR500 GRADED RELIABILITY SPECIFICATIONS