Product Guide & Specifications
For inquiries and orders, please contact: [email protected] 1 2 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
Table of contents...... Pages
LUBCHEM – EVERLAST PRODUCTS • EV1 - Multi-purpose Lubricant • EV1WG / EV1AG - Low Temp Multi-purpose Lubricant • EV3 - High Temp / High Pressure...... 5
• EV960 - Hydrocarbon Resistant • EV960WG - Low Temp Hydrocarbon Resistant • EV960AG - Extreme Low Temp Hydrocarbon Resistant...... 6
• EV3WG / EV3AG - Low Temp / High Pressure • EV4 - Hydrocarbon Resistant • EV4B - Gate Valve Lubricant / Sealant...... 7
• EV146 - Hydrocarbon Resistant • EVK - 1000 High Temp Valve Lube • EVWR - Severe Corrosive Service...... 8
• EV117 - EP Valve Lubricant / Sealant • 50-300 - Low Temp Valve Lubricant / Sealant • 50-400 - Valve Lubricant / Sealant (H2S & C02)...... 9
• 50-400HV - High Viscosity Valve Lubricant / Sealant (H2S & C02) • 50-400H20 - Frac Valve Lubricant / Sealant (H2S & C02) • 50-400DA - Low Temp Valve Lubricant / Sealant (H2S & C02)...... 10
• 50-400WG - Plug Valve Sealant / Ball and Gate Valve Lubricant (H2S & C02) • 50-400AG - Plug Valve Sealant / Ball and Gate Valve Lubricant (H2S & C02) • 50-500 - Plug Valve Sealant / Ball and Gate Valve Lubricant (H2S & C02)...... 11
• LLM - Longlife Moly Heavy Duty Moly Lubricant • SVD / SVC - 102 Special – Peanut Butter Type (Standard and Creamy) • M196 – 196 Sealant for McEvoy Valves...... 12
LUBCHEM – FORMASIL PRODUCTS • FWR - Valve Sealant • FRS - Valve Sealant • FHD - Valve Sealant • FRG - Valve Sealant • ARS - Arctic Grade Sealant • FH2O - Valve Sealant...... 13
• FSCW - Winter Grade • FCO2 - Valve Lubricant / Sealant (H2S & C02)...... 14
For inquiries and orders, please contact: [email protected] 3 Table of contents...... Pages
LUBCHEM – VALVE STEM PACKING • 1900 - TFE Seal ...... 14
LUBCHEM – VALVE CLEANERS / VALVE FLUSH
• VSAW - Valve Cleaner / Lubricant • VSB - Valve Cleaner • LVF – Honey Oil Valve Flush Cleaner...... 15
LUBCHEM – PREMIUM LUBRICANTS • BPA - Longlife 1600 A Arctic Grade Lubricant • LL1600 - Longlife Multi-Purpose Lubricant • LL1603 - Longlife Multi Purpose Lubricant ...... 16
•SRL50 – Longlife SRL50 Sucker Rod Lubricant...... 17
LUBCHEM – INDUSTRIAL PRODUCTS • Copper Coat 1800 • 2200 Anti-Seize - Aluminum Flakes • LUBE-ZIT - Penetrating Oil & Lubricant...... 18
• MOLY-VAP - Dry Moly Lubricant • PROCOAT 690 - Pipe Coating and Corrosion Inhibitor...... 19
LUBCHEM – WIRELINE PRODUCTS...... 20 LUBCHEM – VALVE CAPACITY CHART...... 21 LUBCHEM – ORDERING INFORMATION...... 22
4 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 Lubchem Valve 23609 W. Hardy Rd., Spring, TX 77373 Lubricants / Sealants Order: 800-929-0244 Fax: 281-288-0849
Everlast 1 Everlast 1 WG/AG Everlast 3 Multi-Purpose Lubricant Low Temp Multi-Purpose High Temp/High Pressure
Product Code Product Code Product Code EV1 Winter Grade - EV1WG EV3 Arctic Grade - EV1AG
Everlast 1 is a biodegradable synthetic Everlast 1 Winter Grade and Arctic Grade Everlast 3 is a synthetic lubricant for lubricant for use in valves carrying aliphatic are low temp synthetic lubricants for use high-temperature applications in hydrocarbon hydrocarbon liquids and gases including, in valves carrying aliphatic hydrocarbon service. Everlast 3 is chemically resistant kerosene, fuel oils, crude distillates; sweet liquids and gases including, kerosene, fuel to aliphatic liquids and gases including or sour, water, condensate, dilute acids and oils, crude distillates; sweet or sour, water, gasoline and kerosene, fuel and lubricating caustics. It is waterproof and has excellent condensate, LPG systems, dilute acids and oils, natural gas and brine water. Everlast 3 resistance to oxidation and high metal caustics. It is waterproof, and has excellent is effective at temperatures to 550°F and adhesion. Everlast 1 should be used as a resistance to oxidation. is fortified with antirust, anti-wear, and hydrocarbon resistant ball and gate valve corrosion inhibitors. The unique additive lubricant. Everlast 1 is approved by most Applications package in Everlast 3 bonds to metal major valve manufacturers. • Designed for low torque valve operation surfaces reducing the damaging effects of in cold environments corrosion and scale deposition on critical Applications • For use in gate, plug and ball valves valve components. • For use in plug, gate and ball valves • Suitable for use in hydrocarbon gases • Suitable for use in hydrocarbon gases • DO NOT use in oxygen service Applications • DO NOT use in oxygen service • For use in plug, gate and ball valves Features • Suitable for use in hydrocarbon gases Features • Water resistant • DO NOT use in oxygen service • Water resistant • Fully additive treated • Fully additive treated • High metal adhesion Features • 100% synthetic • Excellent corrosion resistance • 100% synthetic • High metal adhesion • Inhibited for H2S • Water resistant • Inhibited for H2S • Fully additive treated Physical Properties • High metal adhesion Physical Properties • Consistency, Cone Penetration • Inhibited for H2S • Consistency, Cone Penetration (D-217) WG 230 to 280 / AG 230 to 250 (D-217) 200-230 • Dropping Point, °F (D-566) Physical Properties • Dropping Point, °F (D-566) None • Consistency, Cone Penetration None • Oil Separation, % wt. loss (D-1742) (D-217) 150-200 • Oil Separation, % wt. loss (D-1742) 5 max • Dropping Point, °F (D-566) 5 max • Rust Preventative Test (D-1743) None • Rust Preventative Test (D-1743) Pass • Oil Separation, % wt. loss (D-1742) Pass • Temperature Range 5 max • Temperature Range Winter Grade -40° to 450°F • Rust Preventative Test (D-1743) -20° to 400°F Arctic Grade -70° to 620°F Pass • Color • Color • Temperature Range Amber Amber -10° to 550°F • Type Oil • Type Oil • Color Synthetic Synthetic Tan • Corrosive Inhibitor • Corrosive Inhibitor • Type Oil Imidazoline Derivative Imidazoline Derivative Synthetic • EP Additive • EP Additive • Corrosive Inhibitor Diester Type Diester Type Imidazoline Derivative • EP Additive Diester Type
For inquiries and orders, please contact: [email protected] 5 Lubchem Valve Lubricants / Sealants
Everlast 960 Everlast 960 WG Everlast 960 AG Hydrocarbon Resistant Low Temp Hydrocarbon Extreme Low Temp Resistant Hydrocarbon Resitant Product Code EV960 Product Code Product Code EV960WG EV960AG
Everlast 960 is a dual-purpose lubricant/ Everlast 960 Winter Grade offers superb Everlast 960 Arctic Grade is the only valve sealant formulated using Lubchem’s internal valve protection in cold climates. It lubricant which allows for extreme low tem- proprietary premium Lube flex base has excellent dual resistance to water and perature pumpability while being insoluble oils. It is highly insoluble in the most petroleum products. Everlast 960 WG is for- in hydrocarbons. Everlast 960 AG is formu- extreme hydrocarbon, solvent and gas mulated from Lubchem’s proprietary line of lated from Lubchem’s proprietary Lubeflex environments. Everlast 960 is a blend of Lubeflex base oils. Lubeflex oils provide an line of base oils. These oils are unique in synthetic oils for use in valves carrying LPG, insoluble lubricant coating of internal valve that they are insoluble in a multitude of LNG, aliphatic hydrocarbon liquids and components which shields metal surfaces different hydrocarbons while at the same gases including kerosene, fuel oils, sweet from the harsh hydrocarbon environments time allowing for minimal valve torque at and sour crude distillates, dilute acids, and while maintaining ease in pumpability in extreme low temperatures. Everlast 960 caustics. Everlast 960 provides the highest cold environments. AG is a synthetic lubricant formulated for level of protection by adhering to and high chemical and mechanical stability to coating internal valve surfaces. It is water general hydrocarbon service. The synthetic resistant and has excellent resistance to Applications polymer oils used in Everlast 960 AG make • For use in ball, plug, and gate valves oxidation. this an excellent all purpose valve lubricant • DO NOT use in oxygen service and sealant for the oilfield in extreme low • CO2 service <40% Applications temperatures. • For use in ball, plug, and gate valves • DO NOT use in oxygen service Features Applications • CO2 service <40% • 100% synthetic • For use in ball, plug, and gate valves • Contains Moly • DO NOT use in oxygen service • High metal adhesion Features • Not recommenced for alcohol service • Non-Melting • CO2 service <20% • Extremely insoluble • Water resistant • 100% synthetic • Environmentally friendly • Contains Moly Features • High metal adhesion • 100% synthetic • Non-Melting Physical Properties • Contains Moly • Environmentally friendly • Temperature range -40°F to 400°F • High metal adhesion • Water resistant • Consistency, Cone Penetration (D-217) • Non-Melting 225-255 • Environmentally friendly • Dropping Point - >288°C Physical Properties • Rust Preventative Test (D-1743) – Pass • Temperature range -10°F to 400°F • Color Physical Properties • Consistency, Cone Penetration (D-217) Charcoal Gray • Temperature range -75°F to 350°F 205-215 • Consistency, Cone Penetration (D-217) • Dropping Point - >288°C 245 to 260 • Rust Preventative Test (D-1743) – Pass • Dropping Point - >288°C • Color • Rust Preventative Test (D-1743) – Pass Charcoal Gray • Color Charcoal Gray
6 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
Everlast 3 WG/AG Everlast 4 Everlast 4B Low Temp/High Pressure Hydrocarbon Resistant Gate Valve Lubricant/Sealant
Product Code Product Codes Product Code Arctic Grade - EV3WG EV4 EV4B Winter Grade - EV3AG
Everlast 3 is a premium lubricant for high- Everlast 4 is a biodegradable synthetic EVERLAST 4B is a high performance pressure applications in low temperature lubricant formulated for high chemical and synthetic valve lubricant and sealant for hydrocarbon service. Everlast 3 is available mechanical stability to general hydrocar- gate valves. The advanced polymers and in both arctic & winter grades. It is resistant bon service. The synthetic polymer oils extreme pressure additives used in this to aliphatic liquids and gases including used in Everlast 4 make this an excellent all product make it an excellent choice for use gasoline and kerosene, fuel and lubricating purpose plug valve lubricant and sealant for in high-pressure valves carrying natural oils, natural gas and brine water. Everlast the oilfield and petrochemical industries. gas, crude oil, condensate and ethylene. 3 AG is effective to temperatures to -70°F Everlast 4 is a blend of synthetic oils for Everlast 4B contains unique solid lubricant and is fortified with antirust, anti-wear and use in valves carrying LPG, LNG, aliphatic additives that prevent metal to metal con- corrosion inhibitors. The unique additive hydrocarbon liquids and gases including, tact under extreme conditions of pressure package in Everlast 3 bonds to metal kerosene, fuel oils, crude distillates; sweet and temperature. surfaces reducing the damaging effects of or sour, water, condensate, dilute acids and corrosion and scale deposition on critical caustics. It is waterproof and has excellent Performance valve components. resistance to oxidation and high metal Everlast 4B is a specialized lubricant for adhesion. close tolerance valves and will provide Applications outstanding lubricity and high adhesion • Valves in Arctic Climates Applications to polished metal surfaces. This grease • For use in plug, gate and ball valves • For use in plug, gate and ball valves provides corrosion protection and is • Suitable for use in hydrocarbon gases • Suitable for use in hydrocarbon liquids water-resistant. • DO NOT use in oxygen service and gases • DO NOT use in oxygen service Physical Properties Features • Color • 100% synthetic Features Black • Water resistant • 100% synthetic • Temperature Range • Fully additive treated • Water resistant -20°F to 450°F • High metal adhesion • Fully additive treated • Penetration, 25 Deg. C, WKD, 60 STR. • Inhibited for H2S • High metal adhesion 195-220 • Inhibited for H2S • Drop Point, Deg. C Physical Properties None • Consistency, Cone Penetration Physical Properties (D-217) 230-250AG / 235-280WG • Consistency, Cone Penetration • Dropping Point, °F (D-566) (D-217) 150-200 None • Dropping Point, °F (D-566) • Oil Separation, % wt. loss (D-1742) None 5 max • Oil Separation, % wt. loss (D-1742) • Rust Preventative Test (D-1743) 5 max Pass • Rust Preventative Test (D-1743) • Temperature Range Pass Winter Grade -40° to 620°F • Temperature Range -10° to 450°F • Arctic Grade -70° to 620°F • Color • Color Brown Gray • Type Oil Synthetic • Corrosive Inhibitor Imidazoline Derivative
For inquiries and orders, please contact: [email protected] 7 Lubchem Valve SealantsLubricants / Sealants
Everlast 146 Everlast 1000 Everlast WR Hydrocarbon Resistant High Temp Valve Lube Severe Corrosive Service
Product Codes Product Codes Product Code EV146 EVK EVWR
Everlast 146 is a synthetic lubricant Premium synthetic oils and inorganic Lubricant for use in valves carrying CO2, formulated for high chemical and mechani- thickeners make Everlast 1000 a high H2S, NGL, methanol, crude oil, produced cal stability to general hydrocarbon service. temperature, non-melting lubricant/ waters, strong acids, natural gas, and The synthetic polymer oils used in Everlast sealant for valves in geothermal, petroleum fuels where extreme temperature swings 146 make this an excellent all purpose gate refineries and natural gas plants. This high may occur. Everlast WR is highly chemical valve lubricant and sealant for the oilfield. temperature lubricant/sealant is formulated resistant, has a wide temperature range Everlast 146 is a blend of synthetic oils for for resistance to aliphatic hydrocarbons and is fortified with antirust, anti-wear, and use in valves carrying LPG, LNG, aliphatic including gasoline, kerosene, propane, corrosion inhibitors. The unique additive hydrocarbon liquids and gases including, butane, natural gas, steam, hot oil, dilute package in Everlast WR bonds to metal kerosene, fuel oils, crude distillates; sweet acids and caustic solutions. Everlast 1000 is surfaces reducing wear and the damaging or sour, water, condensate, dilute acids and an excellent moly/graphite type anti-seize effects of corrosion due to organic acid caustics. It is waterproof and has excellent compound and should be used to protect attack. resistance to oxidation and high metal threaded connections from galling, and adhesion. wear. Everlast 1000 converts to a dry film Applications lubricant at elevated temperatures and will • For use in plug, gate and ball valves Applications not harden. • Suitable for use in hydrocarbon gases • For use in gate valves • DO NOT use in oxygen service • Suitable for use in hydrocarbon liquids Features and gases • Non melting Features • DO NOT use in oxygen service • Converts to a solid film lubricant • 100% synthetic • Contains molybdenum disulfide (moly) • Water resistant Features • Fully additive treated • 100% synthetic Physical Properties • High metal adhesion • Water resistant • Consistency, Cone Penetration (D-217) • Inhibited for H2S and CO2 • Fully additive treated 200 to 225 • High metal adhesion • Dropping Point, °F (D-566) Physical Properties • Inhibited for H2S None • Color • Oil Separation, % wt. loss (D-1742) White Physical Properties 5 max • Cone Penetration • Consistency, Cone Penetration • Density, lb./gal 185-230 (D-217) 205-215 7.85 • Dropping Point, 5 (ASTM D-566) • Dropping Point, °F (D-566) • Temperature Range -20° to 1000°F None None • Color • Water Washout ASTM D-1264) 1hr @ • Oil Separation, % wt. loss (D-1742) Black 105°F - 0.1% 5 max • Rust Preventative Test (ASTM D-1743) • Rust Preventative Test (D-1743) Pass Pass • Temperature Range • Temperature Range -70° to 600°F -10° to 450°F • Type Oil • Color Synthetic Black • Type Oil Synthetic • Corrosive Inhibitor Imidazoline Derivative • EP Additive Diester Type
8 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
Everlast 117 Everlast 50-300 Everlast 50-400 • H2S & CO2 EP Valve Lubricant Low Temp Valve Lubricant/Sealant
Product Code Product Code Product Code EV117 50300 50400
Everlast 117 is an extreme pressure Everlast 50-300 is a synthetic valve 50-400 is a dual-purpose valve lubricant/ synthetic valve lubricant and sealant for lubricant/sealant formulated for use in sealant that meets Mil-G-6032 gate, ball, and plug valves. Everlast 117 is highly corrosive, low temperature services. “Grease Plug Valve, Gasoline & Oil Resis- designed for use in close tolerance valves 50-300 should be used in plug valves and tant.” 50-400 is designed for use in plug and will provide outstanding lubricity and ball valves handling dry gases including valves as a sealant and in ball and gate reduced operating torque. Extensive labo- natural gas, manufactured gas, LP gases, valves as a lubricant 50-400 is resistant to ratory evaluation has shown Everlast 117 to carbon dioxide, sour crude and gas, salt organic acids, caustic solutions and is inhib- reduce operating torque by up to 50%. The water, hydrocarbons, acids or caustic ited for use in H2S and/or CO2. This product additive package in this product provides solutions. 50-300 is a tenacious filmer has excellent dual resistance to water and excellent antioxidant, extreme pressure to metal surfaces and will protect valve petroleum products such as gasoline, jet and anti-wear properties and should be parts from the corrosive effects of oil and fuel, lubricating oils and mixtures of these used where extreme pressures prevail. gas production and processing. 50-300 is products. 50- 400 can be used in a wide excellent body filler in gate valves where variety of applications from the wellhead to hydrocarbon resistance is important and product pipelines. Applications corrosion protection is critical. • For use in gate valves, plug and ball valves Applications • Suitable for use in hydrocarbon gases, Applications • For use in plug, gate and ball valves water, CO2 and H2S • For use in plug, ball and gate valves in low • Suitable for use in hydrocarbon gases • DO NOT use in oxygen service temperature environments • DO NOT use in oxygen service • Suitable for use in hydrocarbon gases • DO NOT use in oxygen service Features Features • Fully additive treated • Water insoluble and washout resistant • 100% synthetic Features • Fully additive treated • High metal adhesion • Outstanding low temp performance • 100% synthetic • Inhibited for H2S and CO2 • Water insoluble and washout resistant • High metal adhesion • Fully additive treated • Excellent corrosion resistance • 100% synthetic • Inhibited for H2S and CO2 Physical Properties • High metal adhesion • Color • Excellent corrosion resistance Yelow to Brown Physical Properties • Temperature range • Consistency, Cone Penetration -20°F to 450°F Physical Properties (D-217) 215-230 • Penetration, 25°C, wkd, 60 strokes • Consistency, Cone Penetration (D-217) • Dropping Point, °F (D-566) 160-175 245-255 None • Drop Point, °C • Dropping Point, °F (D-566) • Oil Separation, % wt. Loss (D-1742) None None 5 Max • Specific Gravity @25°C • Oil Separation, % wt. Loss, (D-1742) • Rust Preventive Test (D-1743) .98 5 Max Pass • Rust Prevention, (D-1743) • Temperature Range -15° to 400°F Pass • Corrosive Inhibitor Imidazoline • Temperature Range Derivative -60° to 400°F • EP Additive • Color Diester Type Gray • Color • Corrosion Inhibitor Tan Imidazoline Derivative • EP Additive Diester Type
For inquiries and orders, please contact: [email protected] 9 Lubchem Valve SealantsLubricants / Sealants
Everlast 50-400 High Visc Everlast 50-400H20 Everlast 50-400DA Plug Valve H2S & CO2 Frac Valve Lubricant/Sealant Low Temp Valve Lubricant/ Sealant Product Code Product Code 50400HV 50400H20 Product Code 50400DA
50-400 is a high viscosity valve lubricant Everlast 50-400H2O is the preferred 50-400DA is a low temperature valve sealant that meets Mil-G-6032 “Grease Plug lubricant/sealant of frac valve owners and lubricant/sealant resistant to acids, caustic Valve, Gasoline & Oil Resistant.” 50- 400 is renters. 50400H2OH20 is a 100% synthetic solutions and is inhibited for use in H2S designed for use in plug valves as a lubri- frac valve lubricant/sealant containing and/or CO2. 50-400DA has excellent dual cant/sealant. 50-400 is resistant to organic NO solids such as Mica, Titanium Dioxide, resistance to water and aliphatic hydrocar- acids, caustic solutions and is inhibited cheap abrasive Graphite, Molybdenum bons such as gasoline, jet fuel, lubricating for use in H2S and CO2. This product has Disulfide, or other fillers. 50-400H2O oils, organic condensates and mixtures of excellent dual resistance to water and contains Lubchem’s proprietary extreme these products. 50-400DA can be used in a aliphatic hydrocarbons such as gasoline, jet pressure additive package which provides wide variety of applications from the well- fuel, lubricating oils, organic condensates superior protection under the most head to product pipelines and frac valves. and mixtures of these products. 50-400 can demanding conditions. Commonly used be used in a wide variety of applications frac valve lubricants are washed /dissolved Applications from the wellhead to product pipelines. out with each job and valves must be dis- • For use in plug, ball, and gate valves sembled and re-lubricated after each job. • Suitable for use in hydrocarbon gases 50-400H2O does not wash/dissolve out and Applications • DO NOT use in oxygen service valves are only required to be “topped” off • For use in plug valves before sending out to another job. Simply • Suitable for use in hydrocarbon gases put, 50400H2O remains in the valve longer Features • DO NOT use in oxygen service providing superior protection of internal • Water insoluble and washout resistant metal surfaces of the valve without the • Fully additive treated Features harmful solids found in other lubricants. • 100 % synthetic • Water insoluble and washout resistant • High metal adhesion • Fully additive treated • Excellent corrosion resistance • 100% synthetic Applications • Inhibited for H2S and CO2 • High metal adhesion • For use in frac valves, ball valves, and • Excellent low temperature pumpability • Inhibited for H2S and CO2 gate valves • Suitable for use in hydrocarbon gases • DO NOT use in oxygen service Physical Properties Physical Properties • Consistency, Cone Penetration (D-217) • Consistency, Cone Penetration (D-217) 270-280 170-190 Features • Dropping Point, °F (D-566) • Dropping Point, °F (D-566) • Water insoluble and washout resistant None None • Non-Melting • Oil Separation, % wt. loss (D-1742) 5 Max • Oil Separation, % wt. Loss, (D-1742) • 100 % synthetic • Rust Preventive Test (D-1743) No.2 5 max • Contains no fillers • Temperature Range • Rust Prevention, (D-1743) • High metal adhesion -40° to 400°F Pass • Excellent corrosion resistance • Corrosive Inhibitor • Temperature Range • Inhibited for H2S and CO2 Imidazoline Derivative -15° to 400°F • Available in an easier to pump winter • EP Additive • Color grade formula for cold seasons Diester Type, containing no phosphorus Tan sulfur or metal salt • Corrosion Inhibitor Physical Properties Imidazoline Derivative • Consistency, Cone Penetration • EP Additive (D-217) 215-230 Diester Type • Dropping Point, °F (D-566) None • Oil Separation, % wt. loss (D-1742) 5 Max • Rust Preventive Test (D-1743) No.2 • Temperature Range 0° to 450°F • Corrosive Inhibitor Imidazoline Derivative • EP Additive Diester Type, containing no phosphorus sulfur or metal salt
10 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
Everlast 50-400 WG Everlast 50-500 • H2S & CO2 Plug Valve Sealant Ball and Valve Lubricant/Sealant Gate Valve Lubricant Product Code Product Code 50500 50400WG
50-400WG is a dual-purpose valve lubricant/ 50-500 is a dual-purpose valve lubricant/ sealant that meets Mil-G-6032 “Grease Plug sealant that meets Mil-G-6032 “Grease Valve, Gasoline & Oil Resistant”. 50-400WG Plug Valve, Gasoline & Oil Resistant”. is designed for use in plug valves as a 50-500 is designed for use in plug valves sealant and in ball and gate valves as as a sealant and in ball and gate valves as lubricant. 50-400 WG is resistant to acids, a lubricant. 50-500 is resistant to acids, caustic solutions and is inhibited for use in caustic solutions and is inhibited for use in H2S and/or CO2. This product has excellent H2S and/or CO2. This product has excellent dual resistance to water and aliphatic dual resistance to water and petroleum hydrocarbons such as gasoline, jet fuel, products such as gasoline, jet fuel, lubri- lubricating oils, organic condensates and cating oils and mixtures of these products. mixtures of these products. 50-400WG can 50-500 can be used in a wide variety of be used in a wide variety of applications applications from the wellhead to product from the wellhead to product pipelines. pipelines.
Applications Applications • For use in plug, ball, and gate valves • For use in plug, ball and gate valves • Suitable for use in hydrocarbon gases • Suitable for use in hydrocarbon gases • DO NOT use in oxygen service • DO NOT use in oxygen service
Features Features • Meets Mil-G-6032 “Grease Plug • Meets Mil-G-6032 “Grease Plug Valve, Valve, Gasoline and Oil Resistant” Gasoline and Oil Resistant” • Water insoluble and washout • Water insoluble and washout resistant resistant • Fully additive treated • Fully additive treated • 100% synthetic • 100 % synthetic • High metal adhesion • High metal adhesion • Excellent corrosion resistance • Excellent corrosion resistance • Inhibited for H2S and CO2 • Inhibited for H2S and CO2
Physical Properties Physical Properties • Consistency, Cone Penetration • Consistency, Cone Penetration (D-217) 190-205 (D-217) 260-280 • Dropping Point, °F (D-566) • Dropping Point, °F (D-566) None None • Oil Separation, % wt. Loss (D-1742) Max • Oil Separation, % wt. loss (D-1742) • Rust Preventive Test (D-1743) 5 Max Pass • Rust Preventive Test (D-1743) No. 2 • Temperature Range -20° to 500°F • Temperature Range -40° to 400°F • Corrosive Inhibitor Imidazoline • Corrosive Inhibitor Imidazoline Derivative Derivative • EP Additive Diester Type, • EP Additive Diester Type, containing no phosphorus sulfur or containing no phosphorus sulfur metal salt or metal salt • Color • Color Dark Gray Tan
For inquiries and orders, please contact: [email protected] 11 Lubchem Valve Lubricants / Sealants
Longlife Moly 102 Special – Peanut Butter 196 Sealant for McEvoy Heavy Duty Moly Lubricant Type • Standard & Creamy Valves - Regular Grade
Product Code Product Code Product Code: M196 LLM Standard Grade - SVD Creamy Grade - SVC Longlife Moly - 3% Moly-Lithium. EP Grease 196 Special should be used in both res- is a fully additive-treated, multipurpose Recommended for properly sealing WKM ervoirs in McEvoy gate valves to insure grease is water insoluble and is treated for type gate valves handling water, gas and sealing, dependability and easy operation. extra protection. It contains antirust anti- condensate, oil petroleum products such Recommended for properly sealing valves wear, extreme pressure, and antioxidant as gasoline, butane, hydrocarbon vapors, that handle gas and condensate, oils, additives. It is a good quality molybdenum ammonia, glycerin, solvents and sour butane, gasoline, ammonia, glycerin and disulfide compounded multipurpose gas. 102 Special is available in creamy and sour gas. Use Lubchem 196 Sealant for grease and is treated with soluble chemical standard grades. leak proof trouble free service in McEvoy, additives to prevent wear, especially under WKM and other gate valves. Recommended very highly loaded conditions. Use Longlife Physical Properties temperature range 0°F to + 250°F. Moly in general purpose applications where • Appearance Light brown with a medium to severe conditions prevail. characteristic odor Physical Properties Meets Caterpillar requirements for 3% • Density • Appearance Tan with a molybdenum disulfide, lithium soap grease. 9.35 – 9.55 lb. / gal. characteristic odor • Oil Separation will not occur • Density Features • Temperature Range 0° to 250°F 9.35 – 9.55 lb. / gal. • Water insoluble • Cone Penetration: 240-270 • Oil Separation will not occur • Fully additive treated • Corrosion Inhibitor Imidazoline • Meets Caterpillar requirements for • EP Additive 3%molybdenum disulfide, lithium soap Diester type grease • Temperature Range 0° to 250°F • Cone Penetration: 190-220 Physical Properties • Thickener Lithium Stearate • Texture Smooth, but slight iber • Fillers 3% Molybdenum disul ide • Color, Observed Gray • Worked 60 Penetration, D-217 265-295 • Dropping Point, D-566, °F. (°C.) 340 (171) • Oil Separation, D-1742, % loss 3.8 • Rust Prevention, D-1743, rating Pass • Temperature Range 5°F to 280°F
12 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
Formasil WR - Valve Sealant Formasil RS - Valve Sealant Formasil HD - Valve Sealant
Product Code Product Code Product Code FWR FRS FHD
For use in valves carrying hot air, steam, Synthetic sealant for use in valves carrying Synthetic sealant for use in valves CO2, H2S, NGL, methanol, crude oil, natural gas, crude oil; sweet or sour, and carrying natural gas, crude oil; sweet or produced waters, strong acids, natural water. It is waterproof and has excellent sour, water, condensate, dilute acids and gas, and fuels where extreme temperature resistance to oxidation and high metal caustics. It is waterproof and has excellent swings may occur. Formasil WR is highly adhesion. Formasil RS should be used as an resistance to oxidation and high metal chemical resistant, has a wide temperature emergency sealant in ball and gate valves adhesion. Formasil HD should be used as a range and is fortified with antirust, anti- or as a plug valve lubricant sealant. hydrocarbon resistant ball and gate valve wear, and corrosion inhibitors. sealant or as a plug valve lubricant/sealant. Applications Applications • For use in plug, gate and ball valves Applications • Valves in Arctic Climates • Suitable for use in hydrocarbon gases • For use in plug, gate and ball valves • For use in plug, gate and ball valves • DO NOT use in oxygen service • Suitable for use in hydrocarbon gases • Suitable for use in hydrocarbon gases • DO NOT use in oxygen service • DO NOT use in oxygen service Features • 100% synthetic Features Features • Water resistant • 100% synthetic • 100% synthetic • High metal adhesion • Water resistant • Water resistant • Excellent corrosion resistance • High metal adhesion • High metal adhesion • Inhibited for H2S • Inhibited for H2S • Inhibited for H2S • Temperature Range 20° to 400°F • Temperature Range -40° to 400°F • Temperature Range -55° to 450°F • Color • Color • Cone Penetration: 200-240 Gray Green • Cone Penetration: 210-240
Formasil RG - Valve Sealant Formasil RS - Winter Grade Formasil H2O - Valve Sealant Sealant Product Code FRG Product Code Product Code ARS FH2O
Formasil RG is a general purpose synthetic Formasil RS Arctic is a low temperature, For high-pressure gate valve applications sealant for use in valves carrying natural synthetic sealant for use in valves carrying in hydrocarbon service. Formasil H2O is gas, crude oil; sweet or sour, water, natural gas, crude oil; sweet or sour, and chemically resistant to aliphatic liquids and condensate, dilute acids and caustics. It water. It is waterproof and has excellent gases including gasoline, kerosene, fuel and is waterproof and has excellent resistance resistance to oxidation and high metal lubricating oils, natural gas and brine water. to oxidation and high metal adhesion. adhesion. Formasil RS Arctic should be Formasil H2O is effective at temperatures Formasil RG should be used as a hydro- used as an emergency sealant in ball and to 400°F and is fortified with antirust, anti- carbon resistant ball and gate valve sealant gate valves or as a plug valve lubricant/ wear and corrosion inhibitors. or as a plug valve lubricant/sealant. sealant. Applications Applications Applications • Applications • For use in plug, gate and ball valves • For use in plug, gate and ball valves • For use in plug, gate and ball valves • Suitable for use in hydrocarbon gases • Suitable for use in hydrocarbon gases • Drilling choke manifolds • DO NOT use in oxygen service • DO NOT use in oxygen service • High Pressure Gate Valves • Suitable for use in hydrocarbon gases Features Features • DO NOT use in oxygen service • 100% synthetic • 100% synthetic • Water resistant • Water resistant Features • High metal adhesion • Inhibited for H2S • 100% synthetic • Inhibited for H2S • Temperature Range -40° to 400°F • Water resistant • Temperature Range -15° to 400°F • Inhibited for H2S • Cone Penetration: 170-210 • Excellent sealing capabilities • Temperature Range 20° to 400° F • Cone Penetration: 210-240
For inquiries and orders, please contact: [email protected] 13 Lubchem Valve Lubricants / Sealants
Formasil CO2 - Winter Formasil CO2 - Valve TFE Seal Grade Lubricant/Sealant Valve Stem Packing
Product Code Product Code Product Code FSCW FCO2 1900
Synthetic valve sealants formulated for Valve lubricant/sealant that meets Mil-G- A pumpable packing and sealant containing use in highly corrosive, low temperature 6032 “Grease Plug Valve, Gasoline & Oil high temperature proprietary fillers in a services. This product should be used to Resistant.” Formasil CO2 is designed for use blend of synthetic oils. Recommended seal leaking plug valves and ball valves in gate valves as a lubricant/sealant and in for use in high temperature hydrocarbon handling carbon dioxide, sour crude, gas, ball and plug valves as a sealant. Formasil service, steam, and hot oil services. TFE salt water, hydrocarbons, acids or caustic CO2 is resistant to acids, caustic solutions Seal #1 contains fine to medium size filler solutions. and is inhibited for use in H2S and/or CO2. particles. TFE Seal #2 contains medium to This product has excellent dual resistance large filler particles. Applications to water and petroleum products such • For use in plug, ball and gate valves in low as gasoline, jet fuel, lubricating oils and Principle Service temperature environments mixtures of these products. Formasil CO2 • High chemical and mechanical stability • Suitable for use in hydrocarbon gases can be used in a wide variety of applications • Good lubricity • DO NOT use in oxygen service from the wellhead to pipelines. • High temperature fillers • EP Additives Features Features • Oxidation and corrosion inhibitors • Outstanding low temp performance • Water insoluble and washout resistant • 100% synthetic • 100% synthetic Application • High metal adhesion • Inhibited for H2S and CO2 • Pumpable with high pressure grease gun. • Excellent sealing capabilities • Temperature Range 20° to 400° F • DO NOT use in oxygen service • Inhibited for H2S • Cone Penetration: 170-200 • Temperature Range -20° to 350°F • Temperature Range -40° to 350°F • Color • Cone Penetration: 220-240 • Cone Penetration: 260-280 Tan • Color • Color Tan Tan
14 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 Lubchem Valve Cleaners / Valve Flush 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
Valve Saver AW Valve Saver Honey Oil Valve Cleaner/Lubricant Valve Cleaner Valve Flush Cleaner
Product Code Product Code Product Code VSAW VSB LVF
Valve Saver AW is a combination valve Valve Saver is a combination valve cleaner Lubchem LVF valve purge is a unique cleaner and lubricant designed to lubricate and penetrating lubricant engineered to combination of valve penetrant and and clean deposits common to valves in free up and clean out difficult or impossible moisture displacer engineered for today’s pipeline & production valves. Valve Saver to operate lubricated valves. Lubchem’s growing valve maintenance market. AW can be used as a valve cleaner and Valve Saver penetrates and cleans residual as a lubricant. Valve Saver AW consists gum, lacquer, hardened sealants and Features of a premium quality non-melting base lubricants. Valve Saver also penetrates • Water resistant grease, blended with a proprietary additive and loosens rust and corrosion deposits • Stops rust, corrosion, scale inhibitor and package that includes a dispersant / extending the life and performance of oxidation preventative surfactant. This unique compound will all types of lubricated valves. When used • Inhibitive for H2S lubricate the valves internal components regularly it will prevent additional build up. • Dissolves hydrocarbon deposits and at the same time emulsify a variety of • Loosens rust and scale organic and organometallic compounds Features • Will not harm any valve elastomers common to pipeline operations. When • Compatible with all valve lubricants • Non corrosive used regularly it will prevent additional build • Cuts gum and lacquer deposits • Color Tan up of pipeline contaminants. The non- • Removes rust and corrosion melting base grease provides good • DO NOT use in oxygen service lubrication qualities over a wide temperature Application Procedure • Temperature Range -40° to 400°F range of -65° to 300°F. • For use in plug, ball and gate valves • Cone Penetration: 280-330 • Flushing of seized valves prior to • Color lubrication / sealing Valve Saver AW is compatible Black • Suitable for use in hydrocarbon gases with the following elastomers: • DO NOT use in oxygen service Polytetrafluoroethylene, Teflon, Perfluoro- Application Procedure elastomer, Kalrez, Chemraz, TFE-PVDF-Ter- Apply Lubchem Valve Saver with polymer rubber, Viton, Fluorel, Chlorinated conventional lubricating equipment. Butyl Rubber & Butadiene Rubber, Butyl Turn valve slowly and repeat the process Rubber, Ethylene Propylene Rubber, until valve opens freely. After the valve is Ethylene Propylene Diene Rubber, Vistalon, operable, lubricate with one of Lubchem’s Nordel, Nitrile Rubber, Hycar, Buna-N, Natu- high quality valve lubricants. ral Rubber, Butadiene Rubber, Isoprene Rubber, Epichlorohydrin copolymer rubber, Epichlorohydrin terpolymer rubber, Polysul- fide rubber Chlorosulfonated Polyethylene rubber
Features • Compatible with all valve lubricants • Cuts gum and lacquer deposits • Penetrates rust and corrosion • Do not use in oxygen service • Temperature Range -65° to 300°F • Cone Penetration: 280-330 • Color White
For inquiries and orders, please contact: [email protected] 15 Lubchem Premium Lubricants
Longlife 1600 A Longlife 1600 Longlife 1603 Arctic Grade Lubricant Multi-Purpose Lubricant Multi-Purpose Lubricant
Product Code Product Code Product Code BPA LL1600 LL1603
Suitable for use as a low temp gate valve body Longlife 1600 (Bentone) is water insoluble, Longlife 1603 is an economical multipurpose filler or as a ball valve lubricant. Longlife 1600 washout resistant and fully additive treated grease especially suited for normal is a low temperature multipurpose water with corrosion inhibitors, extreme pressure operating temperatures and other insoluble grease that will provide low torque additives and oxidation inhibitor additives. noncritical service applications. 1603 is an operation in very cold operating It is an excellent choice where water excellent corrosion inhibiting grease and environments. It contains a proprietary anti- resistance and a light valve grease is recommended for applications requiring galling additive and corrosion inhibitor recommended. designed to protect seat rings, springs and frequent regreasing due to contaminating sealing surfaces from the corrosive effects of environments. This product is water oil and gas production and processing. Applications insoluble, washout resistant and fully additive treated with corrosion inhibitors, • For use in Ball Valves & Gate Valves as a extreme pressure additives and oxidation Applications body filler inhibitor additives. It is an excellent choice • For use in ball and gate valves in low • Protects seat rings and springs where an economical valve grease is temperature environments • Suitable for use in water and natural gas recommended. • Suitable for use in hydrocarbon gases services • DO NOT use in oxygen service • DO NOT use in oxygen service Applications Features Features • For use in Ball Valves & Gate Valves as a body filler • Outstanding low temp performance • Water insoluble and washout resistant • Protects seat rings and springs • Water insoluble and washout resistant • Fully additive treated • Suitable for use in water and clean • Fully additive treated • Non-melting multipurpose grease natural gas services • Non-melting multipurpose grease • Superior protection to lubricate a wide • DO NOT use in oxygen service • Superior protection to lubricate a wide variety of heavy-duty equipment variety of heavy-duty equipment Features • Low Staining Physical Properties • Water resistant • Temperature Range Physical Properties • Fully additive treated -40° F to 350°F • Multipurpose grease • Thickener Anhydrous Calcium • Color/Texture • Temperature Range Tan/Smooth Physical Properties -75° F to 350° F • Worked 60 Penetration, D-217 • Color/Texture 265-295 • Temperature Range Gray/Smooth Adhesive • Cone Penetration: 265-295 0° to 265° F • Rust Prevention, D-1743, rating • Color Pass Black • Worked 60 Penetration, D-217 • Worked 60 Penetration, D-217 265-295 265-295 • Dropping Point, D-566°F • Dropping Point, D-566°F, (°C) 365 375 (191) • Oil Separation, D-1742, • Texture % loss 5 Smooth, medium fiber • Cone Penetration: 260-330 • Cone Penetration: 265-295
16 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
Longlife SRL-50 Sucker Rod Lubricant
Product Code SRL50
Longlife SRL-50 is engineered to protect the threads of sucker rod connections under severe operating conditions of high cyclic loading. SRL-50 is a high temperature, lithium complex EP grease with excellent low temperature properties. SRL-50 is a unique blend of petroleum base oils and synthetic fluids providing excellent resistance to oxidation at elevated temperatures with exceptional performance under extreme low temperature conditions. SRL-50 contains EP/antiwear additives, rust and oxidation inhibitors that provide superior protection from thread galling in sucker rod connections.
Application: Clean the connection prior to make up. Apply a thin coat of SRL-50 to the thread. CAUTION: Do not lubricate the pin shoulder face or the coupling shoulder face or a loss of tightness can occur resulting in a connection failure.
Physical Properties • Color/Texture Blue/Smooth • Unworked Penetration, D-217 265-295 • Worked 60 Penetration, D-217 265-295 • Oil Separation, D-1742, % loss 1.0 • Dropping Point, (D-2265), °F, (°C) 550 (288) • Temperature Range, °F, (°C) -10°F to 325°F
For inquiries and orders, please contact: [email protected] 17 Lubchem ValveIndustrial Sealants Products
COPPER COAT 1800
Copper Coat 1800 is a anti-seize assembly Anti-Seize 2200 is a special blend of Lubezit is a combination penetrant and lubricant designed to protect stainless graphite and micro size aluminum flake lubricant engineered for maximum pene- steel and dissimilar metals against seizure, particles homogenized into a highly viscous, tration and protection of metal surfaces. galling and heat freeze. It is non-melting nonvolatile carrier. It is non-melting and Lubezit can be used in industrial disman- and contains a high content of micro-size provides superior protection against gall- tling operations, in the home or anywhere copper flakes which are homogenized into ing, corrosion and heat freeze. Anti-Seize metal parts are rusted together or difficult a viscous nonvolatile carrier. Anti-Seize 2200 prevents metal to metal contact to separate. Also, Lubezit provides a 1800 prevents metal to metal contact under under severe variations of temperature, superior corrosion inhibiting film that variations of temperature, cyclic loading cyclic loading and pressure. protects metal in harsh conditions. This and pressure. Prevents seizing and galling. product is safe to use and does not contain It withstands higher temperatures than any environmentally harmful petroleum hy- Recommended uses include all types of copper based compounds and will not drip drocarbons or chlorinated solvents. Lubezit electrical connections, fasteners in engines or run. It will provide clean break-outs from is a selected blend of oils with high quality and turbines and other studs, nuts or bolts high torque and is very economical to use. corrosion inhibiting and extreme pressure operating in high temperature applications. characteristics. It is not harmful to rubber, Uses and Features: plastics or painted surfaces. It’s unique Uses and Features: • Prevents seizure qualities displace moisture, loosen rust, • Electrical connections • Prevents galling scale and protect metal from corrosion. • Protects stainless steel • Provides smooth torque readings • Contains copper flake • Color - silver Applications: • Color - copper • Lead free • Rusted Nuts & Bolts • Lead free • Temperature Range: • Drilling, Cables • Temperature Range: -65° to 2200°F • Lawn Mowers & Tractors -65° to 1800°F -54° to 1200°C • Pulleys & Industrial Parts -54° to 982°C • Flash Point: 380°F • Automobiles & Boats • Flash Point: 380°F • Dropping Point: None • Locks & Hinges • Dropping Point: None • Fishing Gear & Bicycles Applications: Applications: • Bolts & Bushings Features: • Bolts & Burner Assembles • Low RPM Bearings & Gears • Nonflammable & Biodegradable • Bushings & Pumps • Spark Plugs • Lubricates & Penetrates • Conveyors Spark Plugs • Chains & Drives • Nondrying & Nonconductive • Chains & Drives • Cylinder Head Assembles • Dissolves Carbon Deposits • Cylinder Head Assembles • Gaskets • Stops Rust & Protects metal • Steam Turbines • Furnaces • Exhaust Manifolds • Rollers and Conveyors • Shaft Couplings Lubezit is available in: Anti-Seize 1800 is available in: Part Number Description 19119 ...... 1 gal. / 6 cans per case Part Number Description Anti-Seize 2200 is available in: 19145 ...... 5 gallon pail 11211 ...... 24-8 oz. brush top cans Part Number Description 19155 ...... 55 gallon drums 11217 ...... 12-16 oz. brush top cans 13111 ...... 24-8 oz. brush top cans 11223 ...... 10 lb. pail 13117 ...... 12-16 oz. brush top cans 11235 ...... 5 gal./40 lb. pail 13123 ...... 10 lb. pail 13135 ...... 5 gal./40 lb. pail
18 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
Moly-Vap is a dry film lubricant When your specification requires a self containing molybdenum disulfide and healing pipe storage compound then graphite to withstand broad temperature PROCOAT 690 is the product you need. and pressure limits. Moly-Vap film has a The self leveling properties of this product low coefficient of friction ranging from 0.31 allows minor defects in the coating such as to 0.06 and provides excellent lubricating nicks and scratches heal themselves. It’s properties without the attraction of dust self leveling property recovers blemishes and dirt where oils and greases would while it’s balanced system has just the right be unsuitable. The carrier solvent in this thixotropy or gel strength to enable PRO- formulation drys quickly, bonding the COAT 690 to remain in place on the pipe. tenacious solid Moly-Vap coating to ferrous and nonferrous metals. Applications: PROCOAT 690 is engineered to provide Moly-Vap resists water, oils, alkali and most corrosion protection to pipe threads during acids. periods of extended storage. It contains inhibitors to minimize the corrosion effects Applications: of salt water, downhole treating chemicals • Threaded Connections and contaminants. • Assembly • Running In Lubricant Features: • Wire Drawing PROCOAT 690 forms a protective film • Stop-off Coating which deactivates metal surfaces, inhibits • High Temperature Conveyors oxidation and seals out moisture. It resists • Bearings attack from ultraviolet degradation, rust • Chain Lubrication and galvanic corrosion. • Gears • Machine Tools PROCOAT 690 is available in: Moly-Vap prevents friction, fretting, wear, Part Number Description sticking, galling, seizing, binding and 21019 ...... 6 - 1 gal. Cans chattering. 21045 ...... 5 gal can 21056 ...... 55 gal. Drum Moly-Vap is available in: Part Number Description 15112 ...... 12 oz. Aerosol - 12 / case 15119 ...... 6 - 1 gal. cans per case 15145 ...... 5 gal. can 15156 ...... 55 gal. drum
For inquiries and orders, please contact: [email protected] 19 Lubchem WirelineValve Sealants Products
Bio WL-800 Series WL-700 SERIES Wireline Sprays Biodegradable Grease Seal Standard Wireline Fluids Product Code Product Code Product Code WS1113 & WS1500 BWL-816, 820, 824 & 828 WL-716, 720, 724 & 728 Physical Properties Lubchem BWL-800 series grease seals are Lubchem WL-700 wireline grease seals WS 1113 based on biodegradable & renewable base are premium viscous tacky lubricants and ASTM D 445 @ 40 °C, Viscosity 28-48 est oils. Developed to protect wireline exposed sealants designed specifically for use in oil to environments where conventional and gas well logging operations and other WS 1500 wire line sealants fail. Our BWL-800 wireline applications where a lubricating ASTM D 445 @ 40 °C, Viscosity 1350-1650 series is formulated for high temperature dynamic seal is required. Formulated with applications where high levels of H2S and/ advanced corrosion inhibitors to protect or CO2 may be encountered. against corrosion in harsh high pressure down-hole environments where exposure Ashless Hydraulic Oils to moisture, H2S, and corrosive fluids occur. Applications Lubchem Ultra HFA - Ashless Lubchem BWL-800 series is recommended for braided wireline, cables and wire rope. Applications Visc Grades 32, 46, 68 and 100 It is applied by grease injector control Lubchem WL-700 series is recommended heads and cable lubricators. for braided wireline, cables and wire rope. Lubchem Ultra HFA hydraulic fluids are It is applied by grease injector control environmentally acceptable ashless Features heads and cable lubricators. hydraulic oils designed to provide superior • Completely biodegradable oxidation stability, anti-wear & rust • Non-hazardous Benefits preventive properties • Protects against H2S • Enhanced corrosion package Lubchem Ultra HFA meets and exceeds the • Protects against CO2 • Provides lubrication & sealing performance requirements of all major • Fully additive treatment • Minimizes loss of well fluids during pump manufacturers. operation Solubility • Resistant to H2S & CO2 Features • Toluene Insoluble @ 77 °F • Reduces drip and splatter • Contain no zinc or heavy metals • Cyclohexane Insoluble @ 77 °F • Environmentally friendly • Water Insoluble @ 77 °F • Excellent thermal and oxidation stability • Blended from highly refined base oils • Compatible with all OEM fluids Benefits • Enhanced corrosion package • Provides lubrication and sealing Applications • Reduces loss of well fluids during operation • High and low pressure hydraulic systems • Reduces corrosive effects of H2S & CO2 where additive-treated product is required • Reduces drip and splatter • Vane, piston and gear pumps. • Pumps which require an R&O or R&O/AW hydraulic or turbine oil. • Construction, farm, oilfield, mining, and logging equipment.
Meets Performance Standards • Cincinnati Machine P-68; P-69; P-70. • US Steel 127, 136. • Din 5124 (Parts 1&2); Din 51506. • VDL Performance also for lower grades.
Typical Properties Ultra HFA 32 Viscosity @ 40 °C, D445 31.5 - 33.5 Flash Point COC, D92 Min 420 °F Pour Point, D97 Max 5 °F Ultra HFA 42 Viscosity @ 40 °C, D445 45 - 47 Flash Point COC, D92 Min 420 °F Pour Point, D97 Max 15 °F Ultra HFA 68 Viscosity @ 40 °C, D445 66 - 69 Flash Point ,D92 Min 420 °F Pour Point, D97 Max 30 °F 20 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 Lubchem Valve Capacity Chart 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
For additional information or assistance please contact your local Lubchem representative.
The capacities listed in this chart are based upon the valve manufacturers recommendation for the quantity of sealant required per seat. For more information please consult the valve manufacturers maintenance manual or your local Lubchem representative.
Size Cameron Grove Nordstrom KF Series FA KF Series T Valve Lubrication Fitting Thread 1/2 - - 1/2 - - Gauge 3/4 - - 1/2 - - 1 - - 1 - - 1” 1 1/2 - - 1 - 1 2 2 - 3 1 1 3/4” 3 2 - 4 1 2 4 3 - 5 1 2 6 4 3 9 2 2 1/2” 8 5 3 11 4 7 10 6 4 14 5 10 3/8” 12 9 4 17 7 18 14 10 4 32 - 21 16 11 5 40 - 34 1/4” 18 18 5 56 - - 20 20 8 72 - - 1/8” 22 22 10 80 - - 24 23 10 88 - - 26 26 12 96 - - 28 27 13 - - - 30 30 14 112 - - 32 - 14 - - - 34 33 15 - - - 36 42 16 - - - 38 - 16 - - - 40 65 18 - - - 42 67 18 - - - 48 102 22 - - -
Riser Extension Capacity’s
Inside Diameter Ounce Per Foot
1/4” 0.5
3/8” 1.3
1/2” 2.0
3/4” 4.0
For inquiries and orders, please contact: [email protected] 21 Ordering Information
For additional information or assistance please contact your local Lubchem representative.
Lubchem valve lube sealants are available in indus- Ordering Instructions try standard stick and bulk packaging as follows: Product Selection & Part Number Identification:
• 102 Sealant & 196 Sealant - are available in bulk packaging only. Lubchem valve lube sealants are identified by individual product • Everlast Products - are available in both stick and bulk packaging. codes. The product code for each product is listed in this catalog • Formasil Products - are available in bulk packaging only. at the bottom of the each product’s description. When you have selected a product make note of the product code.
Lube Sealant Packaging Selection:
Now that you have selected a product, select the packaging option from the tables below and add the package code to the end of the product code. For example, Everlast 4 packaged in one 40 pound pail would be part number EV440.
Stick Lube Sealant Packaging Options Bulk Lube Sealant Packaging Options
Stick Size Package Container Recommended
Package Diameter Length Sticks per Code Size Pump Code Inches mm Inches mm Box / Carton C10 16 ea. 10oz. Cartridges 1000 Hand Gun A 1/4 6.35 1 1/2 38.5 48 C14 10 ea. 14oz Cartridges 1200 or 1500 Hand Gun B 3/8 9.53 1 1/2 38.1 24 10 10 lb. Pail Force Flow 100 C 7/16 11.11 2 1/8 53.98 24 40 40 lb. Pail FF100, 35-50 or 45-100 D 1/2 12.7 2 5/8 66.68 24 120 120 lb. Drum 16 Gal. Drum Pump G 5/8 15.88 3 1/2 88.9 24 130 130 lb. Drum 16 Gal. Drum Pump J 1 3/8 34.93 8 1/2 215.9 16 420 55 Gal. 420 lb. Drum 55 Gal. Drum Pump K 1 1/2 38.1 10 1/2 266.7 12 400GAL 400 Gal. Tote 400 Gal. Tote Alemite Pump
*Formasil product must be pumped with the Force Flow 100
22 For inquiries and orders, please contact: [email protected] PO Box 2626, Spring, TX 77383 23609 W. Hardy Rd., Spring, TX 77373 Order: 800-929-0244 Fax: 281-288-0849
For inquiries and orders, please contact: [email protected] 23 24 For inquiries and orders, please contact: [email protected]