Goboard Approved Alternative Sealant List

Total Page：16

File Type：pdf, Size：1020Kb

Goboard Approved Alternative Sealant List

GoBoard® Waterproof Tile Installation Materials The GoBoard Installation Instructions / Technical Data Sheet approves two material types for joints and fastener locations sealing in order to achieve a waterproof tile installation: polymer sealant/caulk (in tube); and, 2" wide polymer-coated alkali- resistant fiber glass mesh tape and mortar coated with a liquid waterproofing membrane. Johns Manville does not recommend the use of specific brands, but the following are of the proper material types and tested to comply with ANSI A118.10 when used in combination with GoBoard, GoBoard LT and GoBoard Pro. We do not recommend the use of self-leveling, latex or silicone based sealants. Polymer Sealants/Caulks: • GoBoard Pro Sealant is the preferred sealant and adhesive for all GoBoard products and qualifies for the 10 year limited warranty when used in combination with GoBoard Fasteners or GoBoard Washers per manufacturer’s installation instructions. • OSI® Quad® Max (Model 1868684, 1893977) • DAP Dynaflex® 800 (Model 80800) • DAP 3.0™ (Model 18360) • Rapid Set® Non-Sag Sealant (Model 196330010) • White Lightning® Optima™ White Premium Hybrid Sealant (Model W31200010) • KBRS ShowerSeal® Polyurethane Sealant • QUIKRETE® Polyurethane Non-Sag Sealant (Model 866011, 862017) • SikaBond® Construction Adhesive (Model 106403) • Liquid Nails® Fuze-It® (Model LN-2000) – More of an adhesive, cures harder with less flexibility Liquid Waterproofing Membranes: • MAPEI- Mapelastic AquaDefense Waterproofing and Crack-Isolation Membrane • TEC® – Waterproof & Crack Prevention Membrane • Custom Building Products - RedGard® Waterproofing and Crack Prevention Membrane • KBRS – ShowerSeal® Seamless Liner • Laticrete – Hydro Ban® View the Complete Installation Instructions / Technical Data Sheet: www.JM.com/GoBoard GB-011 5/2021 © 2021 Johns Manville. All Rights Reserved. .

Copy Link

Recommended publications

Tuffak® Polycarbonate Approved Sealants & Adhesives
TUFFAK® POLYCARBONATE APPROVED SEALANTS & ADHESIVES Manufacturer Adhesive Compatibility Ashland Pliogrip Polyurethane 7779/220 Adhesive Compatible Aquascape Pro Silicone Compatible Bostik Hybrid Moisture Cure Adhesive Compatible DAP All Purpose Acrylic Latex Caulk Plus Silicone Compatible DAP 100% Silicone – Window, Door, Siding Compatible Dow Corning 795 Silicone Building Sealant Compatible Dow Corning 995 Silicone Structural Sealant Compatible Dow Corning DC 3‐0117 Silicone Glass Sealant Compatible GE‐Silicones SCS1000 Contractors Compatible GE‐Silicones SCS1200 Construction Compatible GE‐Silicones SCS1700 Sanitary Compatible GE‐Silicones SCS1800 Contractors‐ N Compatible GE‐Silicones SCS2000 SilPruf Compatible GE‐Silicones SCS2350 SilPruf Compatible Compatible/ Highly Recommended‐ No GE‐Silicones SCS2700 Silpruf LM primer needed for good adhesion. Large orders only. GE‐Silicones SCS2800 SilGlaze II Compatible GE‐Silicones SCS2811 SilGlaze II Compatible GE‐Silicones SSG4000 UltraGlaze Compatible GE‐Silicones SSG4000AC UltraGlaze Compatible GE‐Silicones SCS9000 SilPruf NB Compatible GE‐Silicones 100% Silicone II Clear – 30 Minute Rain Ready Compatible GE‐Silicones 100% Clear Silicone II Compatible GE‐Silicones Tub & Tile White 100% Silicone I Compatible Henkel Teroson SI 9160 Black RTV Silicone Adhesive Sealant Compatible Titebond 100% Silicone Clear Compatible TONSAN 1581 Silicone Adhesive Compatible Sashco Big Stretch High Performance Compatible Bostik STR350A Sealant Compatible * Plastic Mark Plasticmask 7550 Compatible * Tremco Proglaze
[Show full text]
Product Data Sheet INSULATING AIR SEALANT Two
330-1075.qxd 12/07/2001 11:05 AM Page 1 Packaging: Product Data Sheet CONTAINER YIELD CONTAINER DIMENSIONS (L x W x H) KITS INSULATING AIR SEALANT SIZE Cubic m Board m* Board Ft. Cubic Ft. mm (Nominal) Inches (Nominal) PER PALLET Z2-200 0.47 5.66 200 16.67 380 x 190 x 368 15 x 7-1/2 x 14-1/2 36 Two-Component Polyurethane Z2-600 1.400 16.99 600 50.00 318 x 305 x 432 12-1/2 x 12 x 17 16 (1A + 1B) (8A + 8B) EXPLANATION reduces waste. Zerodraft Insulating Air Sealant also provides * Board metres = board feet x 0.02832 Buildings with gaps, cracks, and "holes" in them that suffer high yield and quick curing. For application purposes, the gun from uncontrolled air flow (air leakage) cost more money to foam system is the most efficient means of dispensing foam, • "Urethane Foams as Insulating Sealants", Construction Insulating air sealant: Zerodraft Insulating Air Sealant bead heat and air condition, are drafty and uncomfortable, have offers the greatest control, optimum Canada Magazine, March/April 1997. applied gun foam two-component polyurethane sealant to poorer quality indoor air, deteriorate faster, and generate more accuracy and unlimited range of CAN/ULC-S711.1 (Material Specification) as manufactured TECTION applicator motion – an installer O occupant complaints than buildings where air leakage is • "Urethane Foams and Air Leakage Control", Home and distributed by Zerodraft (Division of Canam Building PR properly controlled. convenience when going up and Energy Magazine, July/August 1995. Envelope Specialists Inc.), 125 Traders Blvd.
[Show full text]
Test Method Guidance Document Rule 1168—Adhesive and Sealant Applications
Test Method Guidance Document Rule 1168—Adhesive and Sealant Applications DRAFT July 2018 Table of Contents Introduction ................................................................................................................................... 1 Background ................................................................................................................................... 1 Original Rule .............................................................................................................................. 1 1992 Amendment ......................................................................................................................... 1 1998 Amendment ......................................................................................................................... 2 2000 Amendment ......................................................................................................................... 2 2017 Amendment ......................................................................................................................... 2 Test Method Determination ......................................................................................................... 3 Adhesives ....................................................................................................................................... 4 Sealants .......................................................................................................................................... 6 Test Method Flowcharts for Adhesives
[Show full text]
PLUMBING DICTIONARY Sixth Edition
as to produce smooth threads. 2. An oil or oily preparation used as a cutting fluid espe cially a water-soluble oil (such as a mineral oil containing- a fatty oil) Cut Grooving (cut groov-ing) the process of machining away material, providing a groove into a pipe to allow for a mechani cal coupling to be installed.This process was invented by Victau - lic Corp. in 1925. Cut Grooving is designed for stanard weight- ceives or heavier wall thickness pipe. tetrafluoroethylene (tet-ra-- theseveral lower variouslyterminal, whichshaped re or decalescensecryolite (de-ca-les-cen- ming and flood consisting(cry-o-lite) of sodium-alumi earthfluo-ro-eth-yl-ene) by alternately dam a colorless, thegrooved vapors tools. from 4. anonpressure tool used by se) a decrease in temperaturea mineral nonflammable gas used in mak- metalworkers to shape material thatnum occurs fluoride. while Usedheating for soldermet- ing a stream. See STANK. or the pressure sterilizers, and - spannering heat resistantwrench and(span-ner acid re - conductsto a desired the form vapors. 5. a tooldirectly used al ingthrough copper a rangeand inalloys which when a mixed with phosphoric acid.- wrench)sistant plastics 1. one ofsuch various as teflon. tools to setthe theouter teeth air. of Sometimesaatmosphere circular or exhaust vent. See change in a structure occurs. Also used for soldering alumi forAbbr. tightening, T.F.E. or loosening,chiefly Brit.: orcalled band vapor, saw. steam,6. a tool used to degree of hazard (de-gree stench trap (stench trap) num bronze when mixed with nutsthermal and bolts.expansion 2. (water) straightenLOCAL VENT.
[Show full text]
Sealing Solutions for the Chemical Industry Table of Contents
SEALING SOLUTIONS FOR THE CHEMICAL INDUSTRY TABLE OF CONTENTS 1. INTRODUCTION 3 The Company 3 The chemical industry and its requirements 4 2. SCHEMATIC PROCESS PLANT 6 3. OVERVIEW OF MATERIAL AND PRODUCT PORTFOLIO 8 4. TECHNICAL PLASTICS AND THEIR APPLICATIONS 10 PTFE 11 ePTFE 13 POM, PA, PEEK 14 5. ELASTOMERS AND THEIR APPLICATIONS 15 FKM 16 SIMRIZ 17 EPDM 18 6. PRODUCT PORTFOLIO 19 O-rings 20 Flat gaskets 21 Guide rings 22 Chevron seals 23 Packings 24 Valtec 25 Rotary Shaft Seals 26 PTFE bellows 27 U-cup rings 28 PTFE inlet nozzles 29 Molded parts 30 Diaphragms and Profiles 31 2 Introduction INTRODUCTION PLANT PROCESS SCHEMATIC PORTFOLIO MATERIAL PRODUCT AND PLASTICS THE COMPANY APPLICATIONS THEIR TECHNICAL AND Founded in 1849, the Freudenberg Group is a global tech- From a defined standard product range to customer-specific nology company that remains family-owned until today. developments, Freudenberg Sealing Technologies offers a Consisting of more than 30 market segments, it develops unique product portfolio. technically leading products for a wide range of applica- tions in cooperation with their customers – from sealing Freudenberg Sealing Technologies' market sector process technology through nonwovens to chemicals and medical industry offers sealing solutions especially for the areas: devices. • Food & beverage industry • Chemical industry Freudenberg Sealing Technologies is the largest business • Pharmaceutical industry APPLICATIONS group of the Freudenberg Group. Actin as a supplier, devel- oper and service partner. As a globally leading technology These segments are characterized by high demands on ELASTOMERS THEIR specialist, Freudenberg Sealing Technologies serves sectors the sealing portfolio and the applied materials.
[Show full text]
Childers Selection Guide to Mastics, Coatings, Adhesives and Sealants
Guide to Mastics, Coatings, Adhesives and Sealants for the Thermal Insulation Industry pg. 2-3 pg. 4-5 pg. 4 pg. 6-7 pg. 6 Mastics and Coatings Vapor Sealing Fiberglass Rigid LEED Typical Use Lagging Insulation Facing and Insulation Polystyrene Calcium Volatile 2009 Perm Flash Commercial (C) Product Name Adhesive/ General Description and Jacketing Mineral (Cellular Glass, Coating1 Silicate Component IEQ Rating2 Point or Industrial (I) Coating (FSK, ASJ, FRK) Wool PIR, Phenolic) Credit Greater than 1.0 Ak-Cryl™ Coating Used as mechanical protection and weatherproofing of thermal insulations for indoor and outdoor C Water X Perm for 1/16" None CP-9 (White, Gray) use. Used for piping, tanks, fittings, vessels, equipment and other irregularly shaped objects. Dry Film (Breather) Vi-Cryl® Coating High performance weather barrier mastic/coating. Water-based breather for indoor and outdoor Greater than 1.0 C/I CP-10 (Trowel), CP-11 ( B r u s h ) use. Used over most types of insulation systems operating above ambient and cold, or dual Water X Perm for 1/16" None (White, Gray, Black) • • • • temperature systems where the insulation facing provides a vapor barrier. Dry Film (Breather) Chil-Pruf™ Coating Asphalt cutback based fibrated vapor barrier and weather barrier insulation coating. The cured film Over 0.02 to 0.03 C/I CP-22 (Trowel), CP-24 (Spray) forms a highly impermeable, tough, durable and well-bonded finish. Used over insulations (except Solvent 100ºF Perms (Black) polystyrene) to protect piping, tanks, fittings and vessels. Also protects underground insulation. (37ºC) Water-based asphalt emulsion, weather barrier insulation coating.
[Show full text]
Preparation of Shellac Resin Microcapsules Coated with Urea Formaldehyde Resin and Properties of Waterborne Paint Films for Tilia Amurensis Rupr
membranes Article Preparation of Shellac Resin Microcapsules Coated with Urea Formaldehyde Resin and Properties of Waterborne Paint Films for Tilia amurensis Rupr. Xiaoxing Yan 1,2,* and Lin Wang 2 1 Co-Innovation Center of Efficient Processing and Utilization of Forest Resources, Nanjing Forestry University, Nanjing 210037, China 2 College of Furnishings and Industrial Design, Nanjing Forestry University, Nanjing 210037, China; [email protected] * Correspondence: [email protected] Received: 2 September 2020; Accepted: 9 October 2020; Published: 12 October 2020 Abstract: A two-step in situ polymerization method was utilized to fabricate urea formaldehyde (UF) resin-coated shellac resin microcapsules. The morphology and composition of microcapsules with different core-wall ratios were analyzed by scanning electron microscope (SEM) and infrared (IR) spectrum. The effects of different concentrations of microcapsules on gloss, color difference, hardness, adhesion, and impact resistance of waterborne paint films were studied. At the same time, the self-healing effect of the prepared microcapsules applied to waterborne paint film was discussed. The results revealed that the shellac resin microcapsules coated with UF resin were successfully prepared. At the 0.67:1 and 0.75:1 core-wall ratios, the color differences of the paint film with 0–20.0% (weight percent) microcapsules were small and the color was uniform. Under the condition of 60◦ incident angle and the same microcapsule concentration, a good gloss was obtained. When the concentration was 20.0%, the hardness of paint film reached the maximum value. The adhesion of paint film was better, which was not affected by microcapsule concentration. When the concentration was 5.0% and 10.0%, the microstructure of paint film was good.
[Show full text]
Pipe Joining for Plumbing and Heating Systems
TM 26 January 2020 JOURNAL OF DESIGN INNOVATION FOR HYDRONIC AND PLUMBING PROFESSIONALS Pipe Joining for Plumbing and Heating Systems TM 5212 Series SinkMixer Scald Protection Point-of-use Mixing Valve • 4-way design simplifies piping and minimizes connection points. • Stand-off mounting bracket for simple sturdy installation. • Patented design, wide flow range to handle a variety of fixtures. • Forged low lead dezincification resistant brass for durability. Controlling and protecting your water www.caleffi.com - Milwaukee, WI USA FROM THE GENERAL MANAGER & CEO Dear Plumbing and Hydronic Professional, It was the 1990s when I attempted my first soldering job. What a mess! Although the replacement water softener ended up working fine, my workmanship was nothing short of “bush league”. There was more solder on the basement floor and on the outside of the pipe, than there was in the completed joint. Fortunately the softener was in my own home. I’ve long since moved on from there but would not be surprised if someday that work is posted up on one of those “hacked-up install” websites! That experience gave me an appreciation for the skill that goes into producing a reliable pipe connection in a timely manner. Fast forwarding to today there are several new pipe joining technologies available that not only produce a reliable connection, but require significantly less time than traditional methods. As skilled labor becomes increasingly scarce, it’s likely that manufacturers will introduce even more innovate “quick-joining” technologies and methods. This issue of idronics discusses classic and contemporary methods of joining piping in hydronic and plumbing applications.
[Show full text]
SYGEF® PVDF Pressure Piping System Engineering Handbook
SYGEF® PVDF Pressure Piping Engineering Handbook System 2 Table of Contents Material Characteristics General Information 5 Mechanical Properties 5 Chemical, Weathering and Abrasion Resistance 6 Thermal Properties 6 Flammability and Fire Rated Testing 6 Electrical Properties 7 Physiological Properties 7 Extractables 8 Discoloration Phenomena 8 Manufacturing Complete System of Pipe, Fittings and Valves 9 Compliance with Microelectronic Standards 9 Compliance with Life Science Standards 10 Raw Materials 10 Manufacturing (Pipe) 10 Manufacturing (Fittings/Valves) 11 Manufacturing (Fabricated Products) 12 Traceability of Machined Components 12 Delivery, Storage and Handling 12 General Properties - SYGEF® PVDF 13 SYGEF® Plus HP PVDF Specification - IR/BCF 14 SYGEF® Standard PVDF Specification - IR/BCF 17 SYGEF® Standard PVDF Specification - Socket 20 Pressure/Temperature Long-Term Stress 23 Working Temperature and Pressures for SYGEF® PVDF Pipe and Fittings 23 Dimensional Pipe Size Pipe Size Comparison 24 Calculating Pipe Size Friction Loss Characteristics 25 Hazen and Williams Formula 25 C Factors 25 Flow Rate vs Friction Loss - SYGEF® PVDF (PN16) 26 Flow Rate vs Friction Loss - SYGEF® PVDF (PN10) 30 Friction Loss Through Fittings 33 Gravity Drain Systems Flow Rate for Gravity Drain Systems 34 Surge Pressure (Water Hammer) Surge Pressure (Water Hammer) 35 Special Consideration 36 Expansion/Contraction Allowing for Length Changes in PVDF Pipelines 38 Calculation and Positioning of Flexible Sections 38 Determining the Length Change 39 Determining
[Show full text]
New Joint Sealants. Criteria, Design and Materials
DOCUMENT RESUME EF 002 627 ED 028 602 New Joint Sealants. Criteria,Design and Materials. Budding kesearch Inst., inc.,Washington. D.C. Report No- BR I PUB -1006 Pub Date 62 Note-252p.; Report of a program held as partof the BRI SpringConference, 1962 Institute,1725 De SalesStreet, N. Available from-ExecutiveVice-President,Building Research Washington, D. C. (S12.00). EDRS Price MF-S1.00 HC-S12.70 Construction (Process),Criteria. Design. Descriptors -*Adhesives, ArchitecturalElements, *Building Materials, Glass, *Glossaries, *Sealers,*Specifications (2) sealing glassand metal joints, Contents include--(1) sealingconcrete joints, (4) a theory of (3) metal and glass jointsealants from afabricator's viewpoint, (5) geometry ofsimple joint sealsunder strain, (6) joint adhesion for joint sealants, sealant requirements sealant specificationsfrom a manufacturer'sviewpoint, (7) joint (8) causes of jointsealant failures, (9)polysulfide joint from an applicator's viewpoint, (12) sealants, (10) silicone jointsealants, (11) pdlyethylenesealing compounds, compounds, and(14) epoxy joint polyurethane joint sealants,(13) butyl sealing of terms for sealants. A review ofspecifications for sealants,and a glossary adhesives, cdatings, andsealants are also included.(RH) 1. 5.02, '-w7"N7,,'Invw;1,741r4577-17,7f7.715,71T17777-0,,,,zwr,!,vp , ^ sre. 0', WI' AA,. 41, U 2. 8 6 Crr imareoresibb .140,P4CWHIMAIMMILINOOMMIA Building Research Institute Board of Directors 1962-63 OFFICERS President and Chairman of Executive Committee LEON CHATELAIN, JR. FAIA Chatelain, Gauger & Nolan Vice President and Vice Chairman of Executive Committee OTTO L. NELSON, JR; Vice President for Housing New York Life Insurance Company Vice President Secretary Treasurer PETER B. GORDON MILTON C. COON, JR. GRAYSON GILL Vice President Executive Vice President President Wolff and Munier, Inc.
[Show full text]
Commercial Glazing Guide Glazing Guide Introduction
Architectural Coating Systems COMMERCIAL GLAZING GUIDE GLAZING GUIDE INTRODUCTION For more than 85 years, Tremco has been a market leader in the design, development and manufacture of glazing products for use in commercial construction applications. During this time, processes have changed dramatically for window and curtain wall systems. Window units have become larger, higher performing glass is available, and performance standards have increased — all placing a greater demand on the glazing materials used to seal and support the glass to or within the surrounding metal. As a result, we have continued to evolve, culminating in the development of our Sustainable Building Solutions Test Facility, which is designed for testing connection points in wall assemblies, as well as other building and design challenges facing the built environment. The only single-source supplier offering a complete line of glazing sealants, tapes, and gaskets, Tremco is focused on protecting the entire building envelope and ensuring product compatibility through documented, tested performance. Tremco also supplies compatible perimeter caulking and weatherproofing materials to complement your window or wall system. The details shown in this document describe available materials and their placement for generic applications and are not intended to reflect the actual design of the window unit or system. We recommend you work closely with your Tremco Representative. These experienced individuals will assist in the selection of the proper glazing materials to suit your application and project specification. 2 Factors Influencing Glazing Performance 4 Guidelines for Exceptional Glazing 6 Wet Glazing 8 Wet/Dry Glazing Systems 10 Dry Glazing Systems 12 Structural Silicone Glazing Integrated Systems 14 Sloped Glazing Designed for Superior 16 Plastic Glazing Performance 18 Protective Glazing 19 Hurricane/Impact Resistant Systems 20 Restoration 21 Reglazing Curtain Wall and Window Systems Tremco CS&W has nearly 50 products certified to GREENGUARD and GREENGUARD Children and Schools criteria.
[Show full text]
Curtain Wall Issues, Problems and Solutions
CURTAIN WALL ISSUES , P ROBLEMS , AND SOLUTIONS KARIM P. A LLANA , RRC, RWC, PE; AND DON CARTER ALLANA BUICK & B ERS , I NC . 990 Commercial Street, Palo Alto, CA 94303 Phone: 650-543-5638 • Fax: 650-354-8828 • E-mail: [email protected] S YMPOSIUM ON B UILDING E NVELOPE T ECHNOLOGY • O CTOBER 2012 A LLANA • 97 ABSTRACT Curtain walls are taken for granted, even by design professionals. All curtain wall sys - tems and materials present unique challenges in appearance, design, installation, mainte - nance, and repair. These issues will be addressed by the presenter with real-life, practical examples backed by engineering expertise. The primary focus will be glass curtain walls and window walls, including failures. The presentation is based on the authors’ case studies of the failures of curtain walls, windows, sealants, and flashings, providing useful information on design failures and testing. Included are definitions of curtain wall types, various sys - tems and components, and differences between stick and unitized curtain walls. SPEAKER KARIM P. A LLANA , RRC, RWC, PE — A LLANA BUICK & B ERS , I NC . With more than 25 years of experience in construction engineering, forensic investiga - tion, and design, KARIM ALLANA, RRC, RWC, PE, is CEO and senior principal of Allana Buick & Bers, Inc. He earned his BS in civil engineering from Santa Clara University and is a licensed professional engineer in California, Hawaii, Nevada, and Washington. Allana has been in the AE and construciton fields for over 30 years, specializing in forensic analysis and sustainable construction of roofing, waterproofing, and the building envelope. He has acted as a consultant and expert witness in 200-plus construction defect projects and is a frequent speaker and presenter at professional forums.
[Show full text]