SpanAir™ Metal Ceiling Systems Product Guide

Ceiling Solutions METAL: SpanAir™ / 09 51 33

Reveal the dramatic. Conceal the rest.

With the introduction of SpanAir™, Chicago Metallic expands the options for

expansive ceiling systems. Concealing grid and suspension systems while

providing easy plenum access, SpanAir combines modern, clean lines and

easy point-to-point access in one cost-effective package.

SpanAir™ Planks

SpanAir™ Torsion Spring Panels

SpanAir™ Clip-In Panels

2 METAL: SpanAir™ / 09 51 33

SpanAir™ Planks Aesthetic excellence and design ingenuity come together in SpanAir Planks, where smooth, uninterrupted lines provide an unlikely counterpoint to superior functional convenience. Available in either Hook-In or Hook-On versions, the planks SpanAir EZ Hook-In* are easy to install in conventional suspension and drywall grid components, Ceiling Plank and they can be removed or replaced with no difficulty. Achieve either flat or wave designs by using custom and perimeter trim components.

SpanAir™ Torsion Spring Panels Only their clean, classic look rivals the operational ease and durability of SpanAir EZ Hook-On SpanAir Torsion Spring Panels. A study in visual sophistication and design Ceiling Plank simplicity, they are at once monolithic in appearance and highly accessible. Suitable for interior applications, they integrate seamlessly with factory- slotted suspension grids. All panels come equipped with factory-installed EZ Spring™ feature to facilitate easy shipping and installation.

SpanAir™ Clip-In Panels SpanAir Clip-In Panels make it extraordinarily simple to retrofit and conceal suspension 15/16” grid systems with a fresh, stylish look. These easy-to-install SpanAir Torsion Spring panels provide a dramatic alternative to exposed gridlines, and they’re perfect Panel EZ Spring™ for both new and existing spaces. And because they’re built to last, they save (springs nested) money as well as the resources associated with costly repairs.

An array of advantages All SpanAir components offer aesthetic variety and several practical benefits. • Available in a wide range of standard and custom sizes • A broad variety of finishes and laminates provides options ranging from classic to contemporary • Available in square or beveled edge design SpanAir Clip-in Panels • Engineered to resist rot, decay, sag or warping, even in harsh environments • No VOCs; won’t harm the environment through decay or off-gassing • Made of non-combustible material for a Class A fire rating • Includes a 25-year warranty against manufacturer defects • Enhanced acoustical performance can be achieved with perforation and acoustical backing materials • Coatings that maximize light reflectance and require fewer light fixtures conserve energy • Temperature-controlled environments not essential when installing in an interior environment PRODUCT • All materials can be locally recycled at the end of useful life chicagometallic.com

Popular applications UPDATES Commercial offices, airports, education, recreation, entertainment, Up-to-date, time stamped product information hospitality, healthcare, institutional and retail. is always available on the web

*Patent pending

3 METAL: SpanAir™ Plank Hook-In / 09 51 33 Submittal

SpanAir™ Plank Hook-In

Physical Data

Product

Applications: Material: Edge Details Create spanning, monolithic, .040 recycled aluminum and easily accessible, acoustically enhanceable ceilings for airports, passenger Components: terminals, corridors, assembly halls, convocation centers 1. Planks: and stadiums.  Standard Painted Colors Premium Painted Colors MetalWood® Finishes WoodScenes™ Painted Colors Features: • Planks are constructed Size of recycled aluminum or galvanized steel 12” x 48” 24” x 48” Hook-In Detail • EZ Hook-In* tabs allow plank 12” x 60” 24” x 60” installation in conventional 12” x 72” 24” x 72” drywall grid 12” x 84” 24” x 84” • Hook-In planks for use in 12” x 96” 24” x 96” interior spaces • Square edge design with perimeter gasket Surface Hook-In Gasket on two sides Solid Standard perforation Premium perforation • Standard widths of 12” pattern pattern or 24”, in 5 lengths of up to 96” Profile • Planks available in solid or AMP aluminum (square edge) perforated designs • Hook-In design for Hook-In Webslot Detail downward accessibility 2. Accessories: without special tools Acoutex™ acoustical Encapsulated • Easily incorporates air, fire backer acoustical bag and audio and other services • Planks contain no organic compounds that support mold or microbial growth • Factory applied, no-VOC powder coated paints or laminated finishes Benefits: • Plank attributes may contribute to LEED® Certification project credits • EZ Hook-In tabs make plank installation easier due to use in conventional, suspension grid • Perimeter gasket facilitates ease of plank removal, plank alignment and anti-vibration • No tools required to achieve downward accessibility • Acoustical enhancement is a cinch with a variety of perforation designs and Acoutex™ backer • 100% recycled content; recyclable at end of useful life *Patent pending 4 METAL: SpanAir™ Plank Hook-In / 09 51 33 Submittal

SpanAir™ Plank Hook-In

Physical Data

Product

Sections Perforation Patterns Type: Hook-In Standard Material: Painted anodized aluminum

Surface: Solid and perforated

Size: Widths range—12” or 24”, length range 48”, 60”, 72”, 84” and 96” D 98R216L E 71R138D Edge detail: Square with gasket on two sides

Texture: Smooth

Angle Fire: Class A: flame 0, smoke 0 per ASTM E-84 R 250S750L V 62R250D Sound: NRC 0.70—perforated with Acoutex™ backer NRC 0.90—perforated with acoustical bag

Performance: Interior environments*

Suspension: 640 Drywall HD Main Runner with notched web to J 250R312S Q 60R169L receive plank ends and cross tees

Classification: Type = XX, pattern C, G ASTM E-1264

Warranty: 1 year limited AA 62R354L Sustainability: 75–100% recycled content. 100% locally recyclable at end of useful life Angle Reveal *Consult with engineer to evaluate suitability for intended application. Premium

B 60R169D F 71R195L

Channel

G 125R250L H 125R345

I 188R1000D K 250R345D

Channel with Reveal

L 250R500L N 250R750L

O 375S1125L P 375R1125L Infinity™ Perimeter Trim

W 562R1312L Y 562S1312L

Z 125R500L 5 METAL: SpanAir™ Plank Hook-On / 09 51 33 Submittal

SpanAir™ Plank Hook-On

Physical Data

Product

Applications: Material: Edge Details Create spanning, monolithic, .040 recycled aluminum and easily accessible, acoustically enhanceable ceilings for airports, passenger Components: terminals, corridors, assembly halls, convocation centers 1. Planks: and stadiums.  Standard Painted Colors Premium Painted Colors MetalWood® Finishes WoodScenes™ Painted Colors Features: • Planks are constructed Size of recycled aluminum or width (9” to 24”) ______length (48” to 120”) ______galvanized steel • Hook-On design allows plank installation in drywall grid Surface Hook-On Detail with J-bar on cross tees Solid Standard perforation Premium perforation • Hook-On planks for use in pattern pattern interior spaces • Square edge design Profile with perimeter gasket on two sides AMP aluminum (square edge) • Custom widths of 9” to 24”, Hook-On Gasket and in lengths of up to 120” 2. Accessories: • Planks available in solid or Acoutex™ acoustical Encapsulated perforated designs backer acoustical bag • Hook-On design for downward accessibility without special tools • Easily incorporates air, fire and audio and other services • Planks contain no organic compounds that support mold or microbial growth • Factory applied, no-VOC powder coated paints or Hook-On Cross Tee laminated finishes with J-bar Benefits: • Plank attributes may contribute to LEED® Certification project credits • Hook-On design helps facilitate plank downward accessibility without special tools • Perimeter gasket facilitates ease of plank removal, plank alignment and anti-vibration • Acoustical enhancement is a cinch with a variety of perforation designs and Acoutex™ backer • 100% recycled content; recyclable at end of useful life

6 METAL: SpanAir™ Plank Hook-On / 09 51 33 Submittal

SpanAir™ Plank Hook-On

Physical Data

Product

Sections Perforation Patterns Type: Hook-On Standard Material: Painted aluminum or anodized aluminum

Surface: Solid and perforated

Size: Custom; width range—9” to 24”, length range 48” to 120” (One inch increments) D 98R216L E 71R138D Edge detail: Square with gasket on two sides

Texture: Smooth

Angle Fire: Class A: flame 0, smoke 0 per ASTM E-84 R 250S750L V 62R250D Sound: NRC 0.70—perforated with Acoutex™ backer NRC 0.90—perforated with acoustical bag

Performance: Interior environments*

Suspension: HD drywall main runner with factory-attached J bar J 250R312S Q 60R169L to cross tees

Classification: Type = XX, pattern C, G ASTM E-1264

Warranty: 1 year limited AA 62R354L Sustainability: 75–100% recycled content. 100% locally recyclable at end of useful life Angle Reveal Premium *Consult with engineer to evaluate suitability for intended application.

B 60R169D F 71R195L

Channel

G 125R250L H 125R345

I 188R1000D K 250R345D

Channel with Reveal

L 250R500L N 250R750L

O 375S1125L P 375R1125L Infinity™ Perimeter Trim

W 562R1312L Y 562S1312L

Z 125R500L 7 METAL: SpanAir™ Plank Hook-In / 09 51 33 Specification

SpanAir™ Plank Hook-In

PART 1—GENERAL face by 1-1/2” high by (48) (60) (72) (84) (96) inches long 1.01 Section Includes with (stab) type end tab couplings. A. Provide SpanAir Plank Hook-In Metal Ceiling System b. The manner by which the grid and plank interlock shall also assure manufactured and supplied by Chicago Metallic. that adjacent Hook-In Planks will be level at the ceiling plane. B. Plank Hook-In and Accessories 1.02 Related Sections 1. SpanAir Hook-In Planks: A. Section 09120 Ceiling Suspension Systems a. Planks shall measure (1’ or 2’ x 4’(), (1’ or 2’ x 5’(), (1’ or 2’ x 6’(), B. Section 09545 Special Ceiling Surfaces (1’ or 2’ x 7’(), (1’ or 2’ x 8’()) with (flat) square edge detail, C. Section 13020 Integrated Assemblies with 90-degree upturned legs and non-hardening gasket D. Section 13080 Sound, Vibration, and Seismic Control on two sides, and formed EZ Hook-In legs on short ends to E. Section 15550 Heating, Ventilating, and Air Conditioning assure correct plank interlocking and alignment. F. Section 16500 Lighting b. Planks formed from ((.040) aluminum), (perforated with Chicago Metallic pattern (D)(E)(R)(V)(Q) (Other pattern___) 1.03 References to provide a ______% open. A. American Society for Testing and Materials (ASTM) c. Aluminum shall be painted with a baked powder coat finish 1. C 635—Standard Specification for the Manufacture, or adhesive bonded simulated woodgrain laminate (alumi- Performance, and Testing of Metal Suspension Systems num only). for Acoustical Tile and Lay-In Panel Ceilings. 2. Insulation: 2. C 636—Standard Recommended Practice for Installation a. Poly-encased insulation pads, of (1)),(1-1/2)) thickness and a of Metal Suspension Systems for Acoustical Tile and density of (1), (1-1/2) pcf. Lay-in Panel Ceilings. 3. Plank Inlay: 3. E 84—Test Method for Surface Burning Characteristics of Building Materials. a. Type I—Acoutex™ acoustical non-woven fiber to be inserted in the factory and adhered to the back of the plank for sound 1.04 Submittals absorption capabilities. A. Product data sheets listing plank dimensions, weight, style, and C. Perimeter Treatment standards compliance. 1. Wall Channel: B. Samples: Manufacturer’s sample of each type of ceiling unit (plank) a. Formed from aluminum or .020 galvanized steel, and manu- proposed for each location. factured to a C-shape, with (15/16) top leg, (1-1/4 O.D., and a 1.05 Project Conditions 15/16) bottom leg. Length is 120. A. Environmental Requirements 2. Wall Angle: 1. Verify weather tightness of area to receive system prior a. Formed from aluminum or .020 galvanized steel, and to installation. manufactured to an L-shape, with (15/16) bottom leg and 2. Installation to begin only when temperature and humidity (2-3/16) O.D. Length is 120. conditions closely approximate interior conditions which will 3. Infinity Perimeter Trim: exist when area is complete and occupied. Made from extruded aluminum ((4), (6), (8), (10), (12)) inches 1.06 Maintenance deep. Painted exposed faces or on all sides to match planks. A. Furnish additional material equal to ______% of the ceiling system area. 4. Hold-Down Insert: a. Formed from the same material, with the exception of PART 2—PRODUCTS the finish, as the wall channel. 2.01 Manufacturer b. Manufactured to a C or L-shape with (3/4) legs. Finish shall SpanAir Plank Hook-In Metal Ceiling System, as manufactured by be supplied by manufacturer. Chicago Metallic. 4849 South Austin Avenue, Chicago, IL 60638. 1-800-323-7164. PART 3—EXECUTION 3.01 Examination 2.02 Materials A. Examine area receiving system to identify conditions which will A. Suspension System adversely affect installation. Do not begin installation until adverse 1. Main Carrier: conditions have been remedied. a. Chicago Metallic (640 HD Drywall Suspension) T-shape B. Verify completion of work above ceiling plane prior to plank installation. design with knurled face (concealed). 3.02 Installation b. Formed with openings in grid web to properly receive the EZ Hook-In* tabs of the plank and assure plank interlock and A. Metal planks alignment. The manner by which the grid and plank interlock 1. Metal planks with integral EZ Hook-In legs are appropriately shall also assure that adjacent SpanAir Hook-In Planks will be installed in a Chicago Metallic (1-3/8) grid system. level at the ceiling plane. 2. If necessary, insulation pads shall be laid upon the back of the planks. c. The main carrier shall be formed from .020 hot-dipped 3. If necessary, utilize Chicago Metallic hold-down clips to keep galvanized steel and a length of 144 inches. the insulation pads in place. 2. Cross Tees: 3.03 Repair a. Chicago Metallic (664-C Drywall Suspension) manufactured A. Remove damaged components, replace with undamaged components. from (0.020) (0.012) inch thick 1-3/8” wide with knurled Clean with non-solvent based non-abrasive commercial cleaning solution.

*Patent pending 8 METAL: SpanAir™ Plank Hook-On / 09 51 33 Specification

SpanAir™ Plank Hook-On

PART 1—GENERAL b. The manner by which the grid and plank interlock shall also 1.01 Section Includes assure that adjacent SpanAir Hook-On Planks will be level at the ceiling plane. A. Provide SpanAir Plank Hook-On Metal Ceiling and suspension systems as manufactured and supplied by Chicago Metallic. B. Plank Hook-On and Accessories 1. SpanAir Hook-On Planks: 1.02 Related Sections a. Planks shall measure ((9 – 24”) x (48 – 120”)) with upturned A. Section 09120 Ceiling Suspension Systems ridged legs and non-hardening gasket on two sides, with B. Section 09545 Special Ceiling Surfaces formed hook-on legs on short ends to assure correct plank C. Section 13020 Integrated Assemblies interlocking and alignment. D. Section 13080 Sound, Vibration, and Seismic Control b. Planks formed from ((.040) aluminum) (perforated with E. Section 15550 Heating, Ventilating, and Air Conditioning Chicago Metallic pattern (D)(E)(R)(V) or custom pattern to F. Section 16500 Lighting provide a ______% open.) c. Aluminum planks shall be painted with a baked powder coat 1.03 References finish or adhesive bonded simulated woodgrain laminate A. American Society for Testing and Materials (ASTM) (aluminum only). 1. C 635—Standard Specification for the Manufacture, 2. Insulation: Performance, and Testing of Metal Suspension Systems for a. Poly-encased insulation pads, of (1)),(1-1/2)) thickness and a Acoustical Tile and Lay-In Panel Ceilings. density of (1), (1 1/2) pcf. 2. C 636—Standard Recommended Practice for Installation of Metal 3. Plank Inlay: Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings. a. Type I — Acoutex™ acoustical backer to be inserted in the 3. E 84—Test Method for Surface Burning Characteristics of factory and adhered to the back of the plank for sound Building Materials. absorption capabilities. 1.04 Submittals C. Perimeter Treatment A. Product data: Manufacturers standard data sheets listing dimension 1. Wall Channel: and details. a. Formed from aluminum or .020 galvanized steel, and B. Samples: Manufacturer’s standard samples including suspension, manufactured to a C-shape, with a (15/16) top leg, (3-15/16) panels and colors. O.D. and a (15/16 bottom leg. Length is 120. C. Shop drawings: Reflected ceiling plans and elevations indicating 2. Wall Angle: ceiling layouts, perimeters, and accessories. a. Formed from aluminum or .020 galvanized steel, and 1.05 Quality Assurance manufactured to a L-shape, with a (15/16) bottom leg and A. Materials flame and smoke tested per ASTM E 84 and comply with (4-1/4) O.D. Length is 120. ASTM E 1264 Class A. 3. Infinity Perimeter Trim: B. Environmental Requirements Made from extruded aluminum ((4),(6), (8), (10), (12)) inches deep. Painted exposed faces or on all sides to match planks. 1. Verify weather tightness of area to receive system prior to installation. 4. Hold-Down Insert: 2. Installation to begin only when temperature and humidity a. Formed from the same material, with the exception of the conditions closely approximate interior conditions which will finish, as the wall channel. exist when area is complete and occupied. b. Manufactured to a C or L-shape, with 3/4 inch legs. Finish shall be supplied by manufacturer. 1.06 Maintenance A. Furnish additional material equal to ______% of the ceiling PART 3—EXECUTION system area. 3.01 Examination A. Examine area receiving system to identify conditions which will PART 2—PRODUCTS adversely affect installation. Do not begin installation until adverse 2.01 Manufacturer conditions have been remedied. A. Suspension System B. Verify completion of work above ceiling plane prior to plank installation. 1. Main Carrier: 3.02 Installation a. Chicago Metallic (640-C Drywall Suspension) heavy duty double web suspension: Manufactured from 0.020 inch thick A. Metal Planks steel 1-3/8 inch wide with knurled face by 1-1/2 inches high by 1. Metal planks supported by and appropriately installed with 144 inches long with factory punched cross tee slots, hanger Chicago Metallic manufactured suspension grid system. holes and non-directional bayonet end tab couplings. 2. Insulation pads shall be laid upon the back of the planks if required 2. Cross Tees with attached J-bar: 3. Utilize Chicago Metallic hold-down clips to keep the insulation a. Chicago Metallic (664-C Drywall Suspension): Manufactured pads in place. from (0.020.)(0.012) inch thick 1-3/8 inch wide with knurled 3.03 Repair face by 1-1/2 inches high by 48 inches long with (stab) type A. Remove damaged components, replace with undamaged end tab couplings. J-shape bar manufactured of 0.040 components. Clean with non-solvent based non-abrasive galvanized steel is factory mechanically fastened to the cross commercial cleaning solution. tee web to receive hook-on ends of planks.

9 METAL: SpanAir™ Torsion Spring Panels / 09 51 33 Submittal

SpanAir™ Torsion Spring Panels

Physical Data

Product

Applications: Material: Edge Details Create durable, accessible, .032 aluminum .040 recycled aluminum acoustically enhanceable ceilings for airports, passenger terminals, corridors, assembly Components: halls, convocation centers and stadiums. 1. Panels: • Interior applications  Standard Painted Colors Premium Painted Colors Features: MetalWood® Finishes WoodScenes™ Painted Colors • Torsion spring panels are Torsion Spring Panel constructed of recycled Size Suspension aluminum or steel 24” x 24” 24” x 48” Custom (other): • Torsion springs are ______x ______constructed of high performance steel • EZ Spring™ design allows Surface springs to nest in panels for Solid Standard perforation Premium perforation ease of job site installation pattern pattern • Torsion spring panels integrate into and conceal the suspension grid with Profile slotted face ATS 463 (square edge) • Torsion spring panels for use in interior applications Torsion Spring— • Square edge design 2. Accessories: Springs Up • Standard sizes of 24” x 24”, Acoutex™ acoustical Encapsulated 24” x 48” or custom size backer acoustical bag • Torsion spring panels available in solid or perforated designs • Torsion spring placement allows for downward accessibility • Easily incorporates air, fire, audio and other services • Panels contain no organic compounds that support mold or microbial growth • Factory applied, no-VOC powder coated paints and laminated finishes Benefits: • Torsion spring panel attributes may contribute to LEED® Certification project credits • Torsion Spring Panels easily install in T-bar grid slotted to accept springs • Class A Fire Rating (Non- combustible material) • Acoustical enhancement with a variety of perforation designs and Acoutex™ backer • 100% recycled content; recyclable at end of useful life

10 METAL: SpanAir™ Torsion Spring Panels / 09 51 33 Submittal

SpanAir™ Torsion Spring Panels

Physical Data

Product

Sections Perforation Patterns Type: Torsion spring Standard Material: Painted aluminum or anodized aluminum

Surface: Solid and perforated

Size: 24” x 24”, 24” x 48”, Custom

Edge detail: Square D 98R216L E 71R138D

Texture: Smooth

Fire: Class A: flame 0, smoke 0 per ASTM E-84

Wall Channel Sound: NRC 0.70—perforated with Acoutex™ backer R 250S750L V 62R250D NRC 0.90—perforated with acoustical bag

Performance: Interior environments*

Suspension: 640 Drywall HD Main Runner slotted face to receive torsion springs with cross tees J 250R312S Q 60R169L

Classification: Type = XX, pattern C, G ASTM E-1264

Warranty: 1 year limited Infinity™ Perimeter Sustainability: 75–100% recycled content. 100% locally recyclable Trim at end of useful life AA 62R354L *Consult with engineer to evaluate suitability for intended application. Premium

B 60R169D F 71R195L

G 125R250L H 125R345

I 188R1000D K 250R345D

L 250R500L N 250R750L

O 375S1125L P 375R1125L

W 562R1312L Y 562S1312L

Z 125R500L 11 METAL: SpanAir™ Torsion Spring Panels / 09 51 33 Specification

SpanAir™ Torsion Spring Panels

PART 1—GENERAL b. The cross tee shall be formed from .020 hot dipped galvanized 1.01 Section Includes steel in lengths of 24 or 48 inches. A. Provide SpanAir Torsion Spring Metal Panel Ceiling System B. Torsion Spring Panels and Accessories manufactured and supplied by Chicago Metallic. 1. SpanAir Torsion Spring Panels: 1.02 Related Sections a. Panels shall measure ((2 x 2, 2 x 4), (custom size ____)) with square edge detail, with upturned legs, and formed to A. Section 09120 Ceiling Suspension Systems accept EZ Springs™ on opposing sides for securing panels B. Section 09545 Special Ceiling Surfaces to suspension grid. C. Section 13020 Integrated Assemblies b. Panels formed from (.032, .040 aluminum) D. Section 13080 Sound, Vibration, and Seismic Control (perforated with Chicago Metallic pattern (D)(E)(R)(V) to E. Section 15550 Heating, Ventilating, and Air Conditioning provide a ______% open.) F. Section 16500 Lighting c. Aluminum panels shall be painted with a baked powder coat finish or adhesive bonded simulated woodgrain laminate. 1.03 References 2. Insulation: A. American Society for Testing and Materials (ASTM) a. Poly-encased insulation pads, of (1)),(1-1/2)) thickness and a 1. C 635—Standard Specification for the Manufacture, density of (1), (1 1/2) pcf. Performance, and Testing of Metal Suspension Systems for 3. Panel Inlay: Acoustical Tile and Lay-In Panel Ceilings. a. Type I—Acoutex™ acoustical non-woven fiber to be inserted 2. C 636—Standard Recommended Practice for Installation in the factory and adhered to the back of the panel for sound of Metal Suspension Systems for Acoustical Tile and absorption capabilities. Lay-in Panel Ceilings. C. Perimeter Treatment 3. E 84—Test Method for Surface Burning Characteristics of Building Materials. 1. Wall Channel: 1.04 Submittals a. Formed from .020 electrogalvanized steel, and manufactured to a C-shape, with a (15/16) top leg, (2-7/16) I.D., and a (15/16) A. Product data sheets listing panel dimensions, weight, style, and bottom leg. Length is 120. standards compliance. 2. Wall Angle: B. Samples: Manufacturer’s sample of each type of ceiling unit (panel) proposed for each location. a. Formed from aluminum or .020 galvanized steel, and manufactured to an L-shape, with a (15/16) bottom leg and 1.05 Project Conditions (2-3/4) O.D. Length is 120. A. Environmental Requirements 3. Infinity Perimeter Trim: 1. Verify weather tightness of area to receive system prior Made from extruded aluminum ((4), (6), (8), (10), (12)) inches to installation. deep. Painted exposed faces or on all sides to match panels. 2. Installation to begin only when temperature and humidity 4. Hold-Down Insert: conditions closely approximate interior conditions which will a. Formed from the same material, with the exception of the exist when area is complete and occupied. finish, as the wall channel and angle. 1.06 Maintenance b. Manufactured to a C or L-shape, with (3/4) legs. Finish shall A. Furnish additional material equal to ____% of the ceiling system area. be supplied by manufacturer.

PART 2—PRODUCTS PART 3—EXECUTION 2.01 Manufacturer 3.01 Examination SpanAir Torsion Spring Metal Panel Ceiling System, as manufactured A. Examine area receiving system to identify conditions which will by Chicago Metallic. 4849 South Austin Avenue, Chicago, IL 60638. adversely affect installation. Do not begin installation until adverse 1-800-323-7164. conditions have been remedied. 2.02 Materials B. Verify completion of work above ceiling plane prior to panel installation. A. Suspension System 3.02 Installation 1. Main Carrier: A. Metal panels: a. HD drywall grid with knurled face (concealed) 1. Torsion Spring Metal Panels with factory inserted EZ Springs™ b. Formed with slots in grid face to properly receive the are appropriately installed in a Chicago Metallic (1-3/8) EZ Springs™ of the panels and to assure panel locking and grid system (concealed). alignment. The manner by which the grid and panels 2. If necessary, insulation pads shall be laid upon the back interlock shall also assure that adjacent SpanAir Torsion of the panels. Spring Panels will be level at the ceiling plane. 3. If necessary, utilize Chicago Metallic hold down clips to keep c. The main carrier shall be formed from .020 hot-dipped the insulation pads in place. galvanized steel and a length of 144 inches. 3.03 Repair 2. Cross Tees: A. Remove damaged components, replace with undamaged a. Interlocking crimped cross tees (2” and 4” ) with 15/16” components. Clean with non-solvent based non-abrasive exposed face, as manufactured by Chicago Metallic. commercial cleaning solution.

12 METAL: SpanAir™ Clip-In Panels / 09 51 33 Specification

SpanAir™ Clip-In Panels

PART 1—GENERAL B. Clip-In Panels and Accessories 1.01 Section Includes 1. SpanAir Clip-In Panels: A. Provide SpanAir Clip-In Metal Panel Ceiling System manufactured a. Panels shall measure ((2 x 2, 2 x 4) or custom size (__x__)) and supplied by Chicago Metallic. with square edge detail, with 90-degree upturned legs, and formed to allow insertion of leaf springs in horizontal legs 1.02 Related Sections with pre-punched holes and clips in pre-punched slots in A. Section 09120 Ceiling Suspension Systems vertical legs, on opposing sides for securing panels to and B. Section 09545 Special Ceiling Surfaces concealing suspension grid. C. Section 13020 Integrated Assemblies b. Panels formed from ((steel), (.032 or .040 aluminum) D. Section 13080 Sound, Vibration, and Seismic Control (perforated with Chicago Metallic pattern (D)(E)(R)(V), (other, E. Section 15550 Heating, Ventilating, and Air Conditioning premium perforation) to provide a ______% open.) F. Section 16500 Lighting c. Aluminum or steel panels shall be painted with a baked powder coat finish or adhesive bonded simulated woodgrain 1.03 References laminate (aluminum only). A. American Society for Testing and Materials (ASTM) 2. Insulation: 1. C 635—Standard Specification for the Manufacture, a. Poly-encased insulation pads, of (1)),(1-1/2)) thickness and a Performance, and Testing of Metal Suspension Systems panel density of (1), (1 1/2) pcf. for Acoustical Tile and Lay-In Panel Ceilings. 3. Panel Inlay: 2. C 636—Standard Recommended Practice for Installation a. Type I—Acoutex™ acoustical non-woven fiber to be inserted of Metal Suspension Systems for Acoustical Tile and in the factory and adhered to the back of the panel for sound Lay-in Panel Ceilings. absorption capabilities. 3. E 84—Test Method for Surface Burning Characteristics C. Perimeter Treatment of Building Materials. 1. Wall Channel: 1.04 Submittals a. Formed from .020 electrogalvanized steel, and A. Product data sheets listing panel dimensions, weight, style, and manufactured to a C-shape, with a (15/16) top leg, (2-7/16) standards compliance. I.D., and a (15/16) bottom leg. Length is 120. B. Samples: Manufacturer’s standard samples including suspension, 2. Wall Angle: panels and colors. a. Formed from aluminum or .020 galvanized steel, and 1.05 Project Conditions manufactured to an L-shape, with a (15/16) bottom leg and A. Environmental Requirements (2 -3/4) O.D. Length is 120. 1. Verify weather tightness of area to receive system prior 3. Infinity Perimeter Trim: to installation. Made from extruded aluminum ((4), (6), (8), (10), (12)) inches 2. Installation to begin only when temperature and humidity deep. Painted exposed faces or on all sides to match panels. conditions closely approximate interior conditions which will 4. Hold-Down Insert: exist when area is complete and occupied. a. Formed from the same material, with the exception of the finish, as the wall channel and angle. 1.06 Maintenance b. Manufactured to a C or L-shape, with (3/4) legs. Finish shall A. Furnish additional material equal to ______% of the be supplied by manufacturer. ceiling system area. PART 3—EXECUTION PART 2—PRODUCTS 3.01 Examination 2.01 Manufacturer A. Examine area receiving system to identify conditions which will SpanAir Clip-In Metal Panel Ceiling System, as manufactured by adversely affect installation. Do not begin installation until adverse Chicago Metallic. 4849 South Austin Avenue, Chicago, IL 60638. conditions have been remedied. 1-800-323-7164. B. Verify completion of work above ceiling plane prior to panel installation. 2.02 Materials 3.02 Installation A. Suspension System A. Metal panels: 1. Main Carrier: 1. Clip-In Metal Panels with factory inserted springs and clips a. Chicago Metallic HD/ID, non-rated double web are appropriately installed in a Chicago Metallic (15/16) grid suspension (1200 system with 15/16 inch exposed face). system concealed. b. The main carrier shall be formed from .020 hot-dipped 2. If necessary, insulation pads shall be laid upon the back galvanized steel and a length of 144 inches. of the panels. 2. Cross Tee: 3. If necessary, utilize Chicago Metallic hold down clips to keep a. Stab-in override cross tees (2” and 4”) with 15/16” exposed the insulation pads in place. face, as manufactured by Chicago Metallic. b. The cross tee shall be formed from .020 hot-dipped 3.03 Repair galvanized steel in lengths of 24 or 48 inches. A. Remove damaged components, replace with undamaged components. Clean with non-solvent based non-abrasive commercial cleaning solution.

13 METAL: SpanAir™ Clip-In Panels / 09 51 33 Submittal

SpanAir™ Clip-In Panels

Physical Data

Product

Applications: Material: Edge Details Create durable, accessible, .032 aluminum .040 aluminum Galvanized Steel acoustically enhanceable ceilings for airports, passenger terminals, corridors, assembly Components: halls, convocation centers and stadiums. 1. Panels: • Interior applications  Standard Painted Colors Premium Painted Colors MetalWood® Finishes WoodScenes™ Painted Colors Features: • Clip-In Panels are Size constructed of recycled Clip-In Suspension aluminum or steel 24” x 24” 24” x 48” Custom (other): • Springs and clips are ______x ______constructed of high performance steel Surface • Clip-In Panels integrate Solid Standard perforation Premium perforation into and conceal 15/16” pattern pattern face HD/ID suspension grid • Clip-In Panels for use in interior application Profile • Square edge design ACI 463 (square edge) Clip-In Panel • Standard sizes of 24” x 24”, 24” x 48” or custom size 2. Accessories: • Clip-In Panels available in Acoutex™ acoustical Encapsulated solid or perforated designs backer acoustical bag • Clip-in placement allows for downward accessibility without special tools • Easily incorporates air, fire and audio and other services Clip-In Panel Close-Up • Panels contain no organic compounds that support mold or microbial growth • Factory applied, no-VOC powder coated paints and laminated finishes Benefits: • Clip-In Panel attributes may contribute to LEED® Certification project credits • Clip-In Panels easily install in conventional 15/16” HD/ID T-bar grid • Class A Fire Rating (Non- combustible material) • Acoustical enhancement is a cinch with a variety of perforation designs and Acoutex™ backer • 100% recycled content; recyclable at end of useful life

14 METAL: SpanAir™ Clip-In Panels / 09 51 33 Submittal

SpanAir™ Clip-In Panels

Physical Data

Product

Sections Perforation Patterns Type: Clip-In Panel Standard Material: Painted or anodized aluminum, galvanized steel

Surface: Solid and perforated

Size: 24” x 24”, 24’ x 48”; Custom

Edge detail: Square D 98R216L E 71R138D

Texture: Smooth

Fire: Class A: flame 0, smoke 0 per ASTM E-84

Wall Channel Sound: NRC 0.70—perforated with Acoutex™ backer R 250S750L V 62R250D NRC 0.90—perforated with acoustical bag

Performance: Interior environments*

Suspension: 15/16” HD/ID Main Runner and Cross Tees J 250R312S Q 60R169L Classification: Type = XX, pattern C, G ASTM E-1264

Warranty: 1 year limited

Sustainability: 75-100% recycled content. 100% locally recyclable Infinity™ Perimeter at end of useful life Trim AA 62R354L *Consult with engineer to evaluate suitability for intended application. Premium

B 60R169D F 71R195L

G 125R250L H 125R345

I 188R1000D K 250R345D

L 250R500L N 250R750L

O 375S1125L P 375R1125L

W 562R1312L Y 562S1312L

Z 125R500L 15 Chicago Metallic Product Categories

Metal Ceiling Systems Perimeter / Curvilinear / Plank / Panel / Linear / Open Plenum / Security

Ceiling Panels Premium / Utility / Controlled Environment

Grid Suspension Systems General / Special / Drywall

Ceiling Systems and Specialty Products - USA and Canada: 800.323.7164 / Fax: 800.222.3744 / www.chicagometallic.com belgium / denmark / the netherlands / uk / germany / france / hong kong / china / malaysia / united arab emirates / mexico

Chicago Metallic and its logo are Registered Trademarks of Chicago Metallic Corporation. Infinity, MetalWood and WoodScenes are trademarks of Chicago Metallic Corporation. © 2011 Chicago Metallic Corporation All Rights Reserved Printed in USA SNL5325L0811 Literature Disclaimer: Presentations in this brochure or any other Chicago Metallic Corporation publication are correct to the best of our knowledge at time of preparation. We provide this information in an advisory capacity only. Any advisory recommendations given in our publications must be modified to conform with local codes, conditions and specifications. We reserve all rights to amend any information published in our literature without additional notice. Chicago Metallic can not be held responsible or liable for the selection nor application of our products.