Principles of Structure-Function Relationships Applicable To

Total Page:16

File Type:pdf, Size:1020Kb

Principles of Structure-Function Relationships Applicable To University of Connecticut OpenCommons@UConn Doctoral Dissertations University of Connecticut Graduate School 5-15-2014 Principles of Structure-Function Relationships Applicable To Sensing Materials ─ Explosives and Bio-Diagnosis Hyun-Sook Jang University of Connecticut - Storrs, [email protected] Follow this and additional works at: https://opencommons.uconn.edu/dissertations Recommended Citation Jang, Hyun-Sook, "Principles of Structure-Function Relationships Applicable To Sensing Materials ─ Explosives and Bio-Diagnosis" (2014). Doctoral Dissertations. 399. https://opencommons.uconn.edu/dissertations/399 Principles of Structure-Function Relationships Applicable To Sensing Materials -Explosives and Bio-Diagnosis Hyun-Sook Jang, Ph. D University of Connecticut, 2014 Functions of nanomaterials can be strongly dependent on their structures. Therefore, the knowledge of structure-function relationship can provide important information for designing functional materials. This dissertation aims to gain fundamental knowledge through structural analysis of nano-sensing materials for explosives and bio-diagnosis in order to enhance the sensitivity. The main project of my research involved the investigation into the fluorescence and quenching mechanisms of pyrene with a series of organic salts and/or polystyrene of a variety of architectures as well as the function of explosive detection. The major findings of this dissertation includes: (1) the formation of pyrene excimers can be enhanced by high solvent vapor pressure annealing with the polystyrene (2) tetrabutylammonium cation + - (TBA ) can effectively suppress the fluorescence but hexafluorophosphate anion (PF6 ) with TBA+ can counteract this effect at high solvent vapor pressure driven by temperature. This process is reasoned by dynamic quenching, (3) Polystyrene can effectively lower LUMO (lowest unoccupied molecular orbit) level of pyrene, thus facilitating the detection of the nitro-aromatic explosives. This process is presumably accomplished through radiationless energy transfer from polystyrene emission to pyrene absorption resulting in Hyun-Sook Jang – University of Connecticut, 2014 the efficient photoinduced electron transfer (PET) to explosives, (4) the diffusion coefficients of 2,4-DNT (dinitrotoluene) through pyrene/polystyrene films was evaluated and film thickness is found to be a key parameter affecting the diffusion of 2,4-DNT. The second project mainly focused on constructing potential nanotemplates for biocompatible sensing and diagnosis by using the complexes made of phospholipid/gold nanoparticles and phospholipid/polymer. The 2-nm surface-modified gold nanoparticles can be incorporated in the phospholipid bilayers. Such template can be further developed into theranostic carriers for medical imaging or hyperthermia treatment. In addition, I have shown that lipid vesicles can interact with a triblock copolymer forming clusters of vesicles – this template can also be used as sensitive biosensors. Principles of Structure-Function Relationships Applicable To Sensing Materials -Explosives and Bio-Diagnosis Hyun-Sook Jang B.E., Sogang University, 2006 A Dissertation Submitted in Partial Fulfillment of the Requirements For the Degree of Doctor of Philosophy at the University of Connecticut 2014 i © Copyright by Hyun-Sook Jang 2014 ii Approval Page Doctorof PhilosophyDissertation Principlesof Structure-FunctionRelationships ApplicableTo SensingMaterials -Explosivesand Bio-Diagnosis Presentedby Hyun-SookJang, Ph.D. ts- MajorAdvisor V Mu-PingNie\ r t. t/ | AssociateAdvisor U2)" Yt4 AssociateAdvisor Df AssociateAdvisor AssociateAdvisor StevenL. Suib Universityof Connecticut 2014 iii DEDICATON To my beloved mom (Sun-hee Jun), brother (Jae-hyuk Jang) and papa (Dong-wee Jang) whom I will see for sometime in the heaven for their dedication, encouragement and endless love. iv ACKNOWLEDGEMENT The years of pursuing my PhD in UCONN have been the most memorable time for me. There are many great people that I got to know during this period deserve my heartfelt gratitude. First and foremost, I would like to express my sincere gratitude to Prof. Mu-Ping Nieh for his patience, insightful advice, and endless support for the research. Without him, my Ph.D. journey could have not been possible. He was a remarkably active adviser to initiate my potentials and support me with positive views. His door was always widely opened for students and ready for the discussion regardless of topics. I want to thank him that he has given a number of opportunities to expand my network outside of school by attending many national meetings, national lab experiment and National X-ray/Neutron school. I truly respect his educational philosophy and I am grateful that you were with me to get through many things together along my up and down Ph.D. life. I also would like to thank Prof. Yu Lei for his inspiration and creative suggestions, Prof. Douglas Adamson for his support, three classes that I have taken and advice, Prof. Jing Zhao for the guidance about lifetime experiment and warm words for the encouragement and Prof. Steven Suib for his insightful suggestions and experiences about research topic. Because of their profound knowledge, I was exposed to a tremendous amount of learning opportunities. Before coming to USA, I did not have any background about this research topic, but I learned a lot from you. I truly v want to thank each of you for your valuable time to guide me, review my dissertation and to attend my final defense. I appreciate many people for their supports and assistances with various aspects of this project: Dr. Flavio Maran (Univ. of Padova, Italy) for providing gold nanoparticles, Dr. David Uhrig (Oak Ridge National Lab) for synthesizing different architectures of polystyrenes, Dr. Hyun-Seok Cho (Univ. of Alabama) for conducting the cyclic voltammetry experiment for me, and Dr. Boualem Hammouda (NIST) for helping the neutron scattering experiment in NIST. Indeed, I should thank to all the IMS staffs (Jack Gromek for XRD, Marcurs Giotto for NMR, Lichun Zhang and Rogers Ristau for SEM/(HR)- TEM, Gary Lavigne for fluorescence, Raman/IR spectrocopy) who not only trained me to run the instruments but also gave many great suggestions to solve my experimental challenges. I would like to thank everyone in my group members and undergraduate students as well for working and dealing with me for all these years, especially for Ming-Li who was a great batch and lab mate (Hope you get well soon.) and Ying Liu who shared many of those experiences together. It was enjoyable to interact with Andrew Hu, Yan Xia, Wafa Aresh and Chenlu Yu as well. Also, I learned a lot from my undergraduate students (Joshua Lemkin, Rose Cersonsky, Nicholas Fleming and Naomi Tennakoon). Thanks for all the failures and results from your hands. All the best for you guys! vi It was a great pleasure to be friends with the amazing people. I was lucky to meet Dr. Ying Wang who taught me about the initial experiment setup of explosives detection and Dr. Ching-Chang Chung who helped many of my experiments (XRD/SEM) initially. A special thanks goes to Aaron Baldwin for proof reading some of this dissertation. After I arrived in Storrs alone, many Korean seniors or friends in IMS/UCONN helped me to adjust my life safely. I appreciate their support and friendship of Dr. Suk- kyun Ahn, Dr. Ki-Ryong Lee and Joon-Sung Kim. I also thank all my friends and mentors from previous company and KIST in Korea and/or USA for their encouragement and just being there. I deeply appreciate Younghee and Bob Chudy for their warmest care and thoughtful encouragement in my Storrs life. Thanks you for giving me a memorable chapter in my life with you and your family. Finally, I wish to express my deepest gratitude to my lovely family, my mom and brother. They always trusted me undoubtedly and encouraged me with endless love during the most stressful time. I have no adequate words that can express my love to them. Their unconditional love gave me unbelievable motivation and power to accomplish my dissertation research. Thank you being my family and always love you. vii TABLE OF CONTENTS Dedication ………………………………………………………………. iv Acknowledgements …………………………………………………….....v List of Tables…………………………………………………………… xii List of Figures …………………………………………………………..xiii List of Schemes …………………………………………………..........xxiv List of Symbols ……………………………………………………….. xxv List of Abbreviations………………………………………………....xxviii CHAPTER 1. INTRODUCTION.……………………………….......... 1 1.1 Explosives detection…………………………………………………1 1.2. Pyrene as a Fluorophore…………………………………………… 4 1.2.1. Pyrene Monomers (IM) and Excimers (IE)………..……….. 4 1.2.2. Ground-associate dimers…………………………………. 11 1.3. Fluorescence Quenching Mechanism………………………........ 14 1.3.1. Static and Dynamic quenching………………...…….….. 14 1.3.2. Quenching mechanisms………………………………… 16 1.4. Bio-diagnosis ……………………………………………………. 19 1.5. Dissertation objectives …………………………………………… 20 1.6. References ………………………………………………………. 22 CHAPTER 2. INSTRUMENTAL METHODS OF FUNCTIONAL AND STRUCTURAL CHARACTERIZATION…………………. 30 2.1. Fluorescence ………………………………………………….…… 30 viii 2.1.1 Theory………………………………………………….………. 30 2.1.2 Instrumentation ………………………………………………... 32 2.2. Scattering …………………………………………………….…… 34 2.2.1. Small Angle X-ray Scattering (SAXS) ……………….…..…... 40 2.3. Electron microscopy ……………………………………….…. ...... 41 2.3.1. Transmission Electron Microscopy (TEM)…………………... 41 2.4. References …………………………………………….………..…..44 CHAPTER 3. CONTROLLABLE FORMATION OF PYRENE (C16H10)
Recommended publications
  • Vapor-Liquid Equilibrium Measurements of the Binary Mixtures Nitrogen + Acetone and Oxygen + Acetone
    Vapor-liquid equilibrium measurements of the binary mixtures nitrogen + acetone and oxygen + acetone Thorsten Windmann1, Andreas K¨oster1, Jadran Vrabec∗1 1 Lehrstuhl f¨urThermodynamik und Energietechnik, Universit¨atPaderborn, Warburger Straße 100, 33098 Paderborn, Germany Abstract Vapor-liquid equilibrium data of the binary mixtures nitrogen + acetone and of oxygen + acetone are measured and compared to available experimental data from the literature. The saturated liquid line is determined for both systems at specified temperature and liquid phase composition in a high-pressure view cell with a synthetic method. For nitrogen + acetone, eight isotherms between 223 and 400 K up to a pressure of 12 MPa are measured. For oxygen + acetone, two isotherms at 253 and 283 K up to a pressure of 0.75 MPa are measured. Thereby, the maximum content of the gaseous component in the saturated liquid phase is 0.06 mol/mol (nitrogen) and 0.006 mol/mol (oxygen), respectively. Based on this data, the Henry's law constant is calculated. In addition, the saturated vapor line of nitrogen + acetone is studied at specified temperature and pressure with an analytical method. Three isotherms between 303 and 343 K up to a pressure of 1.8 MPa are measured. All present data are compared to the available experimental data. Finally, the Peng-Robinson equation of state with the quadratic mixing rule and the Huron-Vidal mixing rule is adjusted to the present experimental data for both systems. Keywords: Henry's law constant; gas solubility; vapor-liquid equilibrium; acetone; nitrogen; oxygen ∗corresponding author, tel.: +49-5251/60-2421, fax: +49-5251/60-3522, email: [email protected] 1 1 Introduction The present work is motivated by a cooperation with the Collaborative Research Center Tran- sregio 75 "Droplet Dynamics Under Extreme Ambient Conditions" (SFB-TRR75),1 which is funded by the Deutsche Forschungsgemeinschaft (DFG).
    [Show full text]
  • Field Performance Testing of Centrifugal Compressors
    FIELD PERFORMANCE TESTING OF CENTRIFUGAL COMPRESSORS by Roy B. Pais and Gerald J. Jacobik Dresser Industries, Inc. Dresser Clark Division Olean, New York Roy B. Pais is a Head Product Engi­ (flow to speed ratio) . Techniques for varying the � ratio neer at the Clark Division of Dresser for both fixed and variable speed drives are discussed. Industries, Inc., Olean, N.Y., where he has worked since 1970. He has A method of calculating horsepower consumed and the responsibility for the design and de­ capacity of the compressor is shown. Limitations of a field velopment of centrifugal compressors performance test are also commented upon. as well as associated instrumentation and control systems. Field Performance testing of Centrifugal compressors He graduated from the University with meaningful results is an area of considerable interest of Bombay with a B.S. in Mechanical to the process and gas industry. Although much time and Engineering in 1968. In 1970 he ob­ money are spent on a field test, one must remember that tained an M.S. in Mechanical Engineering from the State the accuracy of the results is not always in proportion to University of New York at Buffalo. the amount of effort put into the test. The preferred meth­ He is an active member of the A.S.M.E. and is currently od, of course, is to perform the test in the Manufacturer's Chairman of the Olean Section. Shop where facilities are designed for accurate data ac­ quisition, and subsequent performance computations. Gerald].]acobik is the Test Super· visor of the Dresser-Clark Division Proper planning is essential for conducting a meaning· Test Department, Dresser Industries, ful test.
    [Show full text]
  • PHYSICAL PROPERTIES User's Guide
    PHYSICAL PROPERTIES User’s Guide LICENSE AGREEMENT LICENSOR: Chemstations Inc. 2901 Wilcrest Drive, Suite 305 Houston, Texas 77042 U.S.A. ACCEPTANCE OF TERMS OF AGREEMENT BY THE USER YOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE USING THIS PACKAGE. USING THIS PACKAGE INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS. The enclosed proprietary encoded materials, hereinafter referred to as the Licensed Program(s), are the property of Chemstations Inc. and are provided to you under the terms and conditions of this License Agreement. Included with some Chemstations Inc. Licensed Programs are copyrighted materials owned by the Microsoft Corporation, Rainbow Technologies Inc., and InstallShield Software Corporation. Where such materials are included, they are licensed by Microsoft Corporation, Rainbow Technologies Inc., and InstallShield Software Corporation to you under this License Agreement. You assume responsibility for the selection of the appropriate Licensed Program(s) to achieve the intended results, and for the installation, use and results obtained from the selected Licensed Program(s). LICENSE GRANT In return for the payment of the license fee associated with the acquisition of the Licensed Program(s) from Chemstations Inc., Chemstations Inc. hereby grants you the following non-exclusive rights with regard to the Licensed Program(s): Use of the Licensed Program(s) on more than one machine. Under no circumstance is the Licensed Program to be executed without either a Chemstations Inc. dongle (hardware key) or system authorization code. You agree to reproduce and include the copyright notice as it appears on the Licensed Program(s) on any copy, modification or merged portion of the Licensed Program(s).
    [Show full text]
  • Extended Corresponding States Expressions for the Changes in Enthalpy, Compressibility Factor and Constant-Volume Heat Capacity at Vaporization ⇑ S
    J. Chem. Thermodynamics 85 (2015) 68–76 Contents lists available at ScienceDirect J. Chem. Thermodynamics journal homepage: www.elsevier.com/locate/jct Extended corresponding states expressions for the changes in enthalpy, compressibility factor and constant-volume heat capacity at vaporization ⇑ S. Velasco a,b, M.J. Santos a, J.A. White a,b, a Departamento de Física Aplicada, Universidad de Salamanca, 37008 Salamanca, Spain b IUFFyM, Universidad de Salamanca, 37008 Salamanca, Spain article info abstract Article history: By analyzing data for the vapor pressure curve of 121 fluids considered by the National Institute of Received 2 October 2014 Standards and Technology (NIST) program RefProp 9.1, we find that the first and the second derivatives Received in revised form 19 December 2014 with respect to reduced temperature (Tr) of the natural logarithm of the reduced vapor pressure at the Accepted 16 January 2015 acentric point (T ¼ 0:7) show a well defined behavior with the acentric factor x. This fact is used for Available online 31 January 2015 r checking some well-known vapor pressure equations in the extended Pitzer corresponding states scheme. In this scheme, we then obtain analytical expressions for the temperature dependence of the Keywords: enthalpy of vaporization and the changes in the compressibility factor and the constant-volume heat Vapor pressure curve capacity along the liquid–vapor coexistence curve. Comparisons with RefProp 9.1 results are presented Saturation properties Acentric factor for argon, propane and water. Furthermore, very good agreement is obtained when comparing with Enthalpy of vaporization experimental data of perfluorobenzene and perfluoro-n-heptane.
    [Show full text]
  • Equation of State
    Supercritical Fluid Extraction: A Study of Binary and Multicomponent Solid-Fluid Equilibria by Ronald Ted Kurnik ~ B.S.Ch.E. Syracuse University (1976) M.S.Ch.E. Washington University (1977) SUBMITTED IN PARTIAL FULFILLMENT OF THE REQUIREMENTS FOR THE DEGREE OF DOCTOR OF SCIENCE at the MASSACHUSETTS INSTITUT.E OF TECHNOLOGY May, 1981 @Massachusetts Institute of Technology, 1981 Signature of Author Signature redacted -------""="--------,------------Department of Chemical Engineering May, 1981 Certified by Signature redacted Robert C. Reid i:cnesis Supervisor / Signature redacted Accepted by ARC~J\'ES (_ ;- . _ . = . _ . .. _ MASSACHUSEIT . Chairman, Departmental OFTECHN&&is7rrurE Committee on Graduate Students OCT 2 8 1981 UBRARlES SUPERCRITICAL FLUID EXTRACTION: A STUDY OF BINARY AND MULTICOMPONENT SOLID-FLUID EQUILIBRIA by RONALD TED KURNIK Submitted to the Department of Chemical Engineering on May 1981, in partial fulfillment of the requirements for the degree of Doctor of Science ABSTRACT Solid-fluid equilibrium data for binary and multicom- ponent systems were determined experimentally using two supercritical fluids -- carbon dioxide and ethylene, and six solid solutes. The data were taken for temperatures between the upper and lower critical end points and for pressures from 120 to 280 bar. The existence of very large (106) enhancement (over the ideal gas value) of solubilities of the solutes in the fluid phase was.observed with these systems. In addition, it was found that the solubility of a species in a multicomponent mixture could be significantly greater (as much as 300 per- cent) than the solubility of that same pure species in the given supercritical fluid (at the same temperature and pressure).
    [Show full text]
  • Investigation of Correlations for Prediction of Critical Properties of Pure Components
    Investigation of Correlations for Prediction of Critical Properties of Pure Components A Thesis Submitted to the College of Engineering of Nahrain University in Partial Fulfillment of the Requirements for the Degree of Master of Science in Chemical Engineering by Eba'a Kareem Jassim B.Sc. in Chemical Engineering 2003 Rabia Al-Awal 1428 November 2007 ABSTRACT Prediction of accurate values of critical properties of any pure component is very important because they are often utilized in estimating the physical properties for chemical process design. Experimental measurements of critical properties for components are very difficult. So, in order to obtain accurate critical property values, attention has been turned to calculate it using mostly a group contribution method which is difficult. To overcome this problem efforts where directed to modify or improve equations to calculate critical properties using relatively simple method. In this method, critical temperature, critical volume and critical pressure can be estimated solely from data of the normal boiling point and molecular weight of pure substance by means of successive approximations that are repeated until calculation of critical pressure (PC) converges. The procedure can be summarized as follows: 1. Calculation of critical temperature. 2. Assuming suitable value of critical pressure and calculating critical volume. 3. Calculation of critical compressibility factor. 4. Calculation of critical pressure from the following equation ; Ζ TR P = cc c Vc If PC obtained is different than PC assumed , the procedure repeated until PC -4 obtained is the same as PC assumed with tolerance of 10 . 1. A statistical program was used to obtained the following equation to estimate critical temperature for non – polar and polar compounds using the normal boiling point and molecular weight of pure substance ; I I Tc = −11.5565 − 1.03586Mwt + 2.075167Tb − 0.000281Mwt2 − 0.00131Tb2 + 0.001827MwtTb The AAD% for estimation of critical temperature is 0.9878 % for 114 non- polar compounds and 1.3525 % for 16 polar compounds.
    [Show full text]
  • Phase Equilibria of Methanol–Triolein System at Elevated Temperature And
    Fluid Phase Equilibria 239 (2006) 8–11 Phase equilibria of methanol–triolein system at elevated temperature and pressure Zhong Tang a,∗, Zexue Du a, Enze Min a, Liang Gao b, Tao Jiang b, Buxing Han b a Research Institute of Petroleum Processing, Sinopec, Beijing 100083, China b Institute of Chemistry, Chinese Academy of Science, Beijing 100080, China Received 21 January 2005; received in revised form 12 September 2005; accepted 9 October 2005 Available online 21 November 2005 Abstract The phase behavior of methnol–triolein system was determined experimentally at 6.0, 8.0 and 10.0 MPa in the temperature range of 353.2–463.2 K. The results demonstrated that the miscibility of the system was rather poor at low temperature, and the miscibility could be improved by increasing temperature. At a higher pressure, the miscibility was more sensitive to temperature as pressure was fixed. The critical temperature, critical pressure, and acentric factor of triolein were estimated and the experimental data were correlated using the Peng–Robinson equation of state. The calculated data agreed reasonably with the experimental results. © 2005 Elsevier B.V. All rights reserved. Keywords: Phase equilibrium; Methanol; Triolein; Equation of state; Calculation; High pressure 1. Introduction triglycerides and methanol reported are very limited, especially at elevated pressures. Study on the alcholysis of oils with simple alcohols to pro- Triolein, one of the typical triglycerides, is the most abun- duce fatty acid esters, which are important intermediates, sur- dant component in many plant oils, such as canola, soybean, factants, lubricants as well as an alternative fuel derived from sunflower seed, etc.
    [Show full text]
  • Experimental Investigation of N2O/O2 Mixtures As Volumetrically Efficient Oxidizers for Small Spacecraft Hybrid Propulsion Systems
    Utah State University DigitalCommons@USU All Graduate Theses and Dissertations Graduate Studies 12-2019 Experimental Investigation of N2O/O2 Mixtures as Volumetrically Efficient Oxidizers for Small Spacecraft Hybrid Propulsion Systems Rob L. Stoddard Utah State University Follow this and additional works at: https://digitalcommons.usu.edu/etd Part of the Mechanical Engineering Commons Recommended Citation Stoddard, Rob L., "Experimental Investigation of N2O/O2 Mixtures as Volumetrically Efficient Oxidizers for Small Spacecraft Hybrid Propulsion Systems" (2019). All Graduate Theses and Dissertations. 7690. https://digitalcommons.usu.edu/etd/7690 This Thesis is brought to you for free and open access by the Graduate Studies at DigitalCommons@USU. It has been accepted for inclusion in All Graduate Theses and Dissertations by an authorized administrator of DigitalCommons@USU. For more information, please contact [email protected]. EXPERIMENTAL INVESTIGATION OF N2O/O2 MIXTURES AS VOLUMETRICALLY EFFICIENT OXIDIZERS FOR SMALL SPACECRAFT HYBRID PROPULSION SYSTEMS by Rob L. Stoddard A thesis submitted in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE in Mechanical Engineering Approved: Stephen A. Whitmore, Ph.D. David Geller, Ph.D. Major Professor Committee Member Geordie Richards, Ph.D. Richard S. Inouye, Ph.D. Committee Member Vice Provost for Graduate Studies UTAH STATE UNIVERSITY Logan, Utah 2019 ii Copyright c Rob L. Stoddard 2019 All Rights Reserved iii ABSTRACT Experimental Investigation of N2O/O2 Mixtures as Volumetrically Efficient Oxidizers for Small Spacecraft Hybrid Propulsion Systems by Rob L. Stoddard, Master of Science Utah State University, 2019 Major Professor: Stephen A. Whitmore, Ph.D. Department: Mechanical and Aerospace Engineering Hydrazine has been a widely used primary propellant for small spacecraft systems.
    [Show full text]
  • D 1.2.8 Investigation of Models for Prediction of Transport Properties for CO2 Mixtures
    IMPACTS Project no.: 308809 Project acronym: IMPACTS Project full title: The impact of the quality of CO2 on transport and storage behaviour Collaborative large-scale integrating project FP7 - ENERGY.2012-1-2STAGE Start date of project: 2013-01-01 Duration: 3 years D 1.2.8 Investigation of models for prediction of transport properties for CO2 mixtures Due delivery date: 2013-12-31 Actual delivery date: 2013-12-31 Organisation name of lead participant for this deliverable: SINTEF Energy Research Project co-funded by the European Commission within the Seventh Framework Programme (2012-2015) Dissemination Level PU Public X PP Restricted to other programme participants (including the Commission Services) RE Restricted to a group specified by the consortium (including the Commission Services) CO Confidential , only for members of the consortium (including the Commission Services) IMPACTS Page iii Deliverable number: D 1.2.8 Deliverable name: Investigation of models for transport properties, prediction of CO2 mixtures Work package: WP 1.2 Thermophysical behaviour of CO2 mixtures Lead participant: SINTEF ER Author(s) Name Organisation E-mail Anders Austegard SINTEF Energy research [email protected] Jacob Stang SINTEF Energy research [email protected] Geir Skaugen SINTEF Energy research [email protected] Abstract Several models for transport properties that are suggested in the literature are investigated and compared with collected experimental data on mixtures of CO2. Binary mixtures of CO2 with the impurities Ar, CH4, CO, H2, N2, N2O, O2 or SO2 in temperature, pressure and concentration range relevant for transport, capture and storage. Models for viscosity, thermal conductivity and diffusivity are compared.
    [Show full text]
  • University Microfilms, Inc., Ann Arbor, Michigan the UNIVERSITY of OKLAHOMA
    This dissertation has been 65—9741 microfilmed exactly as received BUXTON, Thomas Stanley, 1931— THE PREDICTION OF THE COMPRESSIBILITY FACTOR FOR LEAN NATURAL GAS-CARBON DIOXIDE MIXTURES AT HIGH PRESSURE. The University of Oklahoma, Ph.D., 1965 Engineering, chemical University Microfilms, Inc., Ann Arbor, Michigan THE UNIVERSITY OF OKLAHOMA GRADUATE COLLEGE THE PREDICTION OF THE COMPRESSIBILITY FACTOR FOR LEAN NATURAL GAS - CARBON DIOXIDE MIXTURES AT HIGH PRESSURE A DISSERTATION SUBMITTED TO THE GRADUATE FACULTY in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY BY THOMAS s ’. BUXTON Norman, Oklahoma 1965 THE PREDICTION OF THE COMPRESSIBILITY FACTOR FOR LEAN NATURAL GAS - CARBON DIOXIDE MIXTURES AT HIGH PRESSURE DISSERTATION COMMITTEE ACKNOWLEDGMENT The author wishes to express his sincere appreciation to the following persons and organizations: Professor J. M. Campbell, who directed this study. Mr. G. F. Kingelin, who assisted with the computer calculations. Phillips Petroleum Company for analysing the gas mixtures. Gulf Research and Development Company for providing financial support. Pan American Petroleum Corporation for printing this dissertation. Ill TABLE OF CONTENTS Page LIST OF TABLES tfcsooso«oooe« = euccco V î X LIST OF ILLUSTRATIONS.............................. viii Chapter I. INTRODUCTION.................................... 1 II. THEORETICAL BACKGROUND - PURE GASES .......... 5 A. Equations of State .................. 5 B. The Principle of Corresponding States. 8 C. Third Parameters ....................... 15 1. A Parameter to Account for Quantum Effects ............... I5 2. Parameters for Nonspherically Shaped and Globular Molecules . 19 3. Polar Moment Parameters ......... 21 4. General Parameters............ 23 III. CHARACTERIZATION OF GAS MIXTURES.............. 33 A. Third Parameters for Mixtures....... 39 B. Pseudocritical Constants from Two Parameter Equations of State ........
    [Show full text]
  • Thermodynamic Models & Physical Properties
    Thermodynamic Models & Physical Properties When building a simulation, it is important to ensure that the properties of pure components and mixtures are being estimated appropriately. In fact, selecting the proper method for estimating properties is one of the most important steps that will affect the rest of the simulation. There for, it is important to carefully consider our choice of methods to estimate the different properties. In Aspen Plus, the estimation methods are stored in what is called a “Property Method”. A property method is a collection of estimation methods to calculate several thermodynamic (fugacity, enthalpy, entropy, Gibbs free energy, and volume) and transport (viscosity, thermal conductivity, diffusion coefficient, and surface tension). In addition, Aspen Plus stores a large database of interaction parameters that are used with mixing rules to estimate mixtures properties. Property Method Selection Property methods can be selected from the Data Browser, under the Properties folder as shown in Figure 13. To assist you in the selection process, the Specifications sheet (under the Properties folder) groups the different methods into groups according to Process type. For example, if you select the OIL-GAS process type, you will be given three options for the Base method: Peng-Robinson, Soave-Redlich-Kwong, and Perturbed Chain methods. These are the most commonly used methods with hydrocarbon systems such as those involved in the oil and gas industries. When you select a property method, you are in effect selecting a number of estimation equations for the different properties. You can see for example, to the right hand side of the Property methods & models box, what equations are being used.
    [Show full text]
  • Field Performance Testing of Centrifugal Compressors
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by Texas A&M University FIELD PERFORMANCE TESTING OF CENTRIFUGAL COMPRESSORS by Roy B. Pais and Gerald J. Jacobik Dresser Industries, Inc. Dresser Clark Division Olean, New York Roy B. Pais is a Head Product Engi­ (flow to speed ratio) . Techniques for varying the � ratio neer at the Clark Division of Dresser for both fixed and variable speed drives are discussed. Industries, Inc., Olean, N.Y., where he has worked since 1970. He has A method of calculating horsepower consumed and the responsibility for the design and de­ capacity of the compressor is shown. Limitations of a field velopment of centrifugal compressors performance test are also commented upon. as well as associated instrumentation and control systems. Field Performance testing of Centrifugal compressors He graduated from the University with meaningful results is an area of considerable interest of Bombay with a B.S. in Mechanical to the process and gas industry. Although much time and Engineering in 1968. In 1970 he ob­ money are spent on a field test, one must remember that tained an M.S. in Mechanical Engineering from the State the accuracy of the results is not always in proportion to University of New York at Buffalo. the amount of effort put into the test. The preferred meth­ He is an active member of the A.S.M.E. and is currently od, of course, is to perform the test in the Manufacturer's Chairman of the Olean Section. Shop where facilities are designed for accurate data ac­ quisition, and subsequent performance computations.
    [Show full text]