BOSS CE-2W Chorus Pedal Owners Manual

Owner’s Manual English

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). After reading, keep the document(s) where it will be available for immediate reference.

* 5 1 0 0 0 5 2 7 8 5 - 0 1 *

Main Features This is a “WAZA CRAFT series” effect unit featuring analog circuitry designed with attention to every detail in pursuit of the finest sound. Standard mode completely replicates the sound of the CE-2 chorus, known for its mild modulation. In addition, this unit provides a CE-1 mode (chorus, vibrato) which reproduces the sound of the world’s first chorus unit, the CE-1.

Panel Descriptions

DC IN jack CHECK indicator Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can This indicator shows whether the effect is on or off, and also doubles as the battery check play without being concerned about how much battery power you have left. indicator. The indicator lights when the effect is on. * Use only the specified AC adaptor (PSA series; sold separately), and connect it to an AC outlet * If you’re powering the unit with a battery and the CHECK indicator goes dim— or of the correct voltage. Do not use any other AC adaptor, since this may cause malfunction. doesn’t light at all—when you try to turn the effect on, the battery is near depletion and should be replaced. For instructions on changing the battery, refer to “Changing * If the AC adaptor is connected while a battery is installed, the AC Adaptor the Battery.” power supply is drawn from the AC adaptor. (PSA series; sold separately) * We recommend that you keep batteries installed in the unit even * The CHECK indicator shows whether the effect is being applied or not. It does not though you’ll be powering it with the AC adaptor. That way, you’ll indicate whether the power to the device is on or not. be able to continue a performance even if the cord of the AC adaptor gets accidentally disconnected from the unit. DEPTH knob RATE knob Adjusts the depth of the chorus. Adjusts the rate of the chorus.

Standard/CE-1 mode switch Switches the mode. OUTPUT A (MONO) jack The direct sound and chorus sound are The sound of the CE-2. mixed and output from this jack. Standard This is a chorus sound notable for its clarity; it will If you use the OUTPUT B jack for stereo not impair the crispness of your guitar sound. output, this jack outputs only the chorus The chorus sound of the CE-1. sound. While providing an easily recognizable chorus CE-1 Chorus Guitar Amplifier effect with deeper modulation, this chorus is distinctively mild. The vibrato sound of the CE-1. CE-1 Vibrato This is a unique chorus with strongly varying modulation. OUTPUT B jack Use this jack for stereo output. The stereo output produced by this INPUT jack output in conjunction with the chorus Electric Guitar sound from the OUTPUT A (MONO) jack This jack accepts signals coming from Thumbscrew a guitar or other musical instrument, or provides a spacious chorus effect. When this screw is loosened, the Only the direct sound is output from the another effects unit. Guitar Amplifier pedal will open, allowing you to * The INPUT jack doubles as the power switch. Power OUTPUT B jack. change the battery. to the unit is turned on when you plug into the * For instructions on changing INPUT jack; the power is turned off when the cable the battery, refer to “Chang- is unplugged. To prevent unnecessary battery Pedal switch ing the Battery.” consumption, be sure to disconnect the plug from This switch turns the effect on/off. the INPUT jack when not using the effects unit.

OUTPUT jacks Use of Battery Specifications Mono output * A battery was installed in the unit before it left the factory. The BOSS CE-2W: Chorus life of this battery may be limited, however, since its primary purpose was to enable testing. Nominal Input Level -20 dBu * If you handle batteries improperly, you risk explosion and fluid Input Impedance 1 MΩ leakage. Make sure that you carefully observe all of the items Nominal Output Level -20 dBu related to batteries that are listed in “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). Output Impedance 1 kΩ Recommended Load * When operating on battery power only, the unit’s indicator will 10 kΩ or greater Chorus sound + Direct sound become dim when battery power gets too low. Replace the Impedance battery as soon as possible. DC 9 V: Carbon-zinc battery (9 V, 6F22)/ * Batteries should always be installed or replaced before Power Supply Alkaline battery (9 V, 6LR61), AC Adaptor Stereo output connecting any other devices. This way, you can prevent (sold separately) malfunction and damage. 25 mA * Expected battery life under continuous Changing the Battery use: Current Draw Carbon: Approx. 18 hours Thumbscrew Pedal 1. Hold down the Alkaline: Approx. 32 hours pedal and loosen Spring Base These figures will vary depending on the thumbscrew, Chorus sound Direct sound Battery Snap the actual conditions of use. then open the Cord Coil Spring 73 (W) x 129 (D) x 59 (H) mm pedal upward. Dimensions 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches * The pedal can be Guide Bush Precautions When Connecting Hole opened without Weight 450 g/1 lb (including battery) * To prevent malfunction and equipment failure, always turn detaching the down the volume, and turn off all the units before making any Battery Owner’s Manual, thumbscrew Snap Leaflet (“USING THE UNIT SAFELY,” connections. Battery Housing Accessories completely. “IMPORTANT NOTES,” and “Information”), * Once everything is properly connected, be sure to follow Alkaline battery (9 V, 6LR61) the procedure below to turn on their power. If you turn on 9 V Battery Option equipment in the wrong order, you risk causing malfunction or 2. Remove the old battery from the battery housing, and AC adaptor (PSA series) (sold separately) equipment failure. remove the snap cord connected to it. When powering up: Turn on the power to your guitar amp * 0 dBu = 0.775 Vrms last. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing. * This document explains the specifications of the product at the When powering down: Turn off the power to your guitar amp * Be sure to carefully observe the battery’s polarity (+ versus -). time that the document was issued. For the latest information, first. refer to the Roland website. 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. 5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely.