Introduction Front Panel (LEDs) DIP Switches Mode Configuration

LED Indicator This is a Long Reach Extender with DIP 1 2 3 4 one Ethernet port (on 1 RJ-45 connector) and one VDSL port on 1 RJ-11 connector. This is a LED Status Description On CO Fast 998ISDN 6dB bridge mode accommodating Ethernet 10/100Base-Tx Long Reach On RJ 45 port full duplex and VDSL technologies to extend Ethernet over Duplex Off CPE Interleave Symmetric 9dB single-pair phone line by using a VDSL signal. Off RJ 45 port half duplex RJ11 Up to 100/60 Mbps (or 90/90 Mbps with On RJ 45 connect at 100M Speed synchronous data rate) transition bandwidth off RJ 45 connect at 10M within 300m and 40/10 Mbps for 1km long range  Pin 1 CPE or CO mode selection On RJ 45 port is link connections provides ultra-high performance to  Pin 2 Interleave mode or fast mode User’s Manual Link/Act RJ 45 port Data is the pervasive telephone line network. Its Blinking plug-n-play solution minimum installation time & transmitting or receiving selection cost by allowing video streaming and data to On Power is on.  Pin 3 Symmetric ISDN Mode or 998 ISDN Power share the same telephone pair without Off Power is off. Mode selection interference. Work as Master at Core On  Pin4 Signal Noise Rate selection for 9dB center With one DIP switches configuration, the CO or 6dB Work as CPE at Edge extender including the CO (Central Office) site off site and CPE (Customer Premise Equipment) site. FCC Warning The long distance support feature makes this Blinking Negotiation Nego extender be a great and ideal solution for FTTx On Link is connected /Link This device has been tested and found to (Fiber to the Building, Fiber to the Campus or flash /Act Data Active comply with limits for a Class A digital device Fiber to the Home) applications. It supports high Blinking and pursuant to Part 15 of FCC Rules. bandwidth VDSL2 over existing telephone wires These limits are designed to provide a in the “last mile” from the ISP / Telecom / Package Contents reasonable protection against harmful Service provider’s fiber mode to the buildings interference when the equipment is operated and customers’ home. Before you start to install this switch, please in a commercial environment. This equipment

verify your package that contains the following generates and radiates radio frequency Key Features items: energy. If it’s not installed and used in

accordance with the user’s manual, it may  1 full-duplex VDSL links via RJ-11 connector  2x Extender cause interference. In which case, users will  Selectable CO and CPE mode  2x Power Adaptor be required to correct interference at their own  1 User Manual expenses.  Selectable fast and interleaved mode  8x Rubber feet  Selectable target SNR margin CE Warning  Compliant with ETSI, ITU and ANSI This is a Class A product. In a domestic standards environment, this product may cause radio interference in which case the user may be required to take adequate measures.

Note: If any of these items is found missing or damaged, please contact your local supplier for replacement.

Mechanical Technical Specifications

IEEE802.3 10Base-T IEEE802.3u 100Base-TX IEEE802.3x Full Duplex ETSI Standards ITU ANSI Full ITU-T G.993.1 (VDSL) compatible G.997.1 compatible. Interface RJ-11 female Phone Jack RJ-45 female Ethernet jack Switching Method Store and Forward Duplex Speed LED Link / Act Indicators Power Master Link / Negotiation Power Input DC 5V/2A 102 × 75 × 23 mm Dimensions (L x W x H) Weight 0.28 kg Operating 0 to 45 Temperature ℃ Storage -20 to 90 Tempe ature ℃ 10 to 90% RH Humidity (non-condensing) Certifications FCC Class B, CE