Metal Work 381-390

METAL WORK INDEX TOOL STEEL DRILL ROD Abrasive Blasting...... 388 Polishing...... 384-388 Indispensable In The Gun Shop For Parts, Tools & Repairs

One of the remarkable features of these tool steels is the low HARDENING: Heat slowly to 1475° F. - 1525° F. If a controlled METAL WORK Engraving & Stamping. . . . . 389-390 Soldering & Welding ...... 382-383 draw temperature to achieve maximum torsion impact strength. furnace is not available, use 1500° Tempilaq. Hold at this tempera- Most drawing can be done in a kitchen oven! Or you can easily make ture for a few seconds then quench in a light quenching oil. Heat-Treating...... 383-384 Springs & Raw Materials. . . . .381-382 a small and efficient draw furnace on your bench using furnace TEMPERING: Temper immediately. The following hardness brick, a simple heat element and a kitchen oven heat control. Draw table is for a one hour draw after oil quenching at 1500° F. Jeweling...... 390 all steel shown one hour. ab For spring temper, draw at 650°-750° F. for 15 minutes. You can use a conventional kitchen oven for some tempering. W-1 WATER HARDENING DRILL ROD - Degrees F. Rockwell C Degrees F. Rockwell C GENERAL USE SPRINGS Carbon - 1.00% Manganese - .40% Silicon - .20% As hardened. . . . 63 - 65 600° ...... 54 - 56 Solve Literally Hundreds Of Spring Needs With These Kits A fine-grained, commercial quality steel, W-1 can be used for 300°...... 63 - 64 700° ...... 51 - 53 tools, parts, dies or punches which require great hardness and a 400°...... 61 - 62 800° ...... 46 - 48 WOLFF LIGHT-DUTY COIL SPRINGS - Kit #4 NO. 150 tough inner core for maximum strength. The sizes we carry should 500°...... 58 - 60 900° ...... 43 - 45 meet 99% of all requirements for pins in guns. 100 Coil springs. 10 designs. O.D.’s from .090" (2.3mm) to .250" Wire Diameters: .020" to .062" HARDENING: Heat the part to 1450° - 1500° F., or slightly higher O-1 OIL HARDENING DRILL ROD - ROUND (6.3mm). Overall lengths from 2" (5.1cm) to 4" (10.2cm). Pitch and SMALL SPRING WIRE - One hundred, (up to 1600° F.) if unusual depth of hardness is required. If a furnace STOCK # SIZE GA. DEC. EQUIV. PRICE ba wire diameter variations provide many loadings. 12" long pieces of assorted music, is not available, use 1450° Tempilaq. Hold at this temperature for a 1 #080-541-250AU /4 .2500 5L4P99 $ 5.99 spring, and piano wire. For making gun few seconds, then quench in an 8% brine solution. Do not use fresh #969-100-410AU Wolff Kit #4, 9F21H99 ��$ 32.99 5 3 #080-541-312AU /16 .3125 5L6H99 $ 7.99 and miscellaneous small springs. An extremely popular gunsmith water! To make a brine solution: Add /4 lb. (340 g) of rock salt to SPRINGS & RAW MATERIALS 3 and sports-repairman assortment. Hand-bendable. ab one gallon of water. #080-541-375AU /8 .3750 5L6H99 $ 7.99 7 WOLFF HEAVY-DUTY COIL SPRINGS - Kit #5 #025-150-000AU No. 150 Spring Assortment, TEMPERING: Temper immediately. A one hour draw at the fol- #080-541-437AU /16 .4375 5L8E99 $ 10.99 8K25F99 ��$ 29.99 lowing temperatures will produce hardness on the Rockwell C scale 1 100 Coil springs. 10 designs. For heavy loadings. O.D.’s from #080-541-500AU /2 .5000 5L10J99 $ 13.99 as follows: 9 .090" (2.3mm) to .250" (6.3cm). 2" (5.1cm) to 4" (10.2cm) long. ab 16 5L16A99 For spring temper, draw at 650°-750° F. for 15 minutes. You can #080-541-562AU / .5625 $ 19.99 5 #969-100-510AU Wolff Kit #5, 9F17P99 �� $ 34.99 NO. 152 use a conventional kitchen oven for some tempering. #080-541-625AU /8 .6250 5L14N99 $ 19.99 11 Wire Diameters: .062" to .120" Degrees F. Rockwell C Degrees F. Rockwell C #080-541-687AU /16 .6875 5L20N99 $ 23.99 ROUND OIL-TEMPERED SPRING STOCK #080-541-100AU 1* 1.000 5L43N99 $ 49.99 WOLFF MASTER COIL SPRING KIT - Kit #345 As hardened. . . . . 66 - 67 500°...... 58 - 59 - Seventy-two 18" lengths of oil-tem- Contains 1 each of these Kits: No. 3 and 4 English; No. 4 Metric; pered spring wire. Ready to be made into 200°...... 66 - 67 600°...... 54 - 55 DRILL ROD ASSORTMENTS - 18" LENGTH ONLY No. 5 English and No. 5 Metric. 5 Kits with a total of 550 highly usable springs. Much heavier than No. 150 As- 300°...... 64 - 65 700°...... 50 - 51 springs. An excellent gun shop assortment. ba #080-541-000AU O-1 Round 18" Drill Rod, Assortment sortment. Can be annealed and re-tem- 7 400°...... 61 - 62 800°...... 46 - 47 of 9 pieces, 1 ea. (no /8" or 1"), #969-100-580AU Wolff Kit #345, 9F76K99 ��$ 119.99 ba pered. 1070 Carbon Steel. 5L91J99 ��$ 107.99 #025-152-000AU No. 152 Spring Assortment, DO NOT USE A MICROWAVE! Preheat the oven to the desired WOLFF MINIATURE COIL SPRING PAK - Kit #1607 8K27K99 �� $ 29.99 temperature prior to inserting the part. ANNEALING METAL TEMPERATURES (Degrees F.) MELTING POINTS (Degrees F.) 50 Miniature coil springs for firearms. O.D.’s from 1/16" (40.6cm) W-1 WATER HARDENING DRILL ROD - ROUND NO. 149 Aluminum 650 Pewter 425-550 to 5/32" (4mm) with English and Metric variations. ba STOCK # SIZE GA. DEC. EQUIV. PRICE Britannia Metal None Brass 930 #969-160-700AU Wolff Kit #1607, 9F9F99 ��$ 14.99 Widths: 3/16" to 3/8" Thicknesses: 1/16" to 1/8". #080-540-066AU #51 .0660 5L3E99 $ 4.99 Pewter None Copper 2000 FLAT SPRING STOCK - 12 assorted pieces #080-540-088AU #43 .0880 5L2D99 $ 3.99 Brass 800-1300 Bronze 1825 flat spring steel stock, cut to 18" lengths. WOLFF COIL SPRING COMBINATION PAK - Kit #1610 5L2E99 Bronze 800-1200 Sterling Silver 1640 No. 1075 Carbon Steel, annealed. For #080-540-097AU #40 .0970 $ 3.99 130 Coil springs. 50 miniature springs as in Kit 1607, above, plus large, flat gun and lock springs. Forges #080-540-101AU #38 .1010 5L2D99 $ 3.99 Copper 700-1200 Fine Silver 1760 30, “stiff” extractor/ejector coil springs; 5 each of 6 designs to take and tempers to gun quality spring re- #080-540-110AU #34 .1100 5L3A99 $ 4.99 Gold Platinum 3223 care of most rifles or shotguns, and 50 firing pin retracting springs; quirements. ba #080-540-115AU #32 .1150 5L3B99 $ 4.99 Red 1100-1200 24 kt. Gold 1945 5 each of 10 designs for most shotguns using a coil spring to retract #025-149-000AU No. 149 Spring Assortment, #080-540-120AU #31 .1200 5L3G99 $ 4.99 White and Yellow 1400 14kt. Yellow Gold 1615 the firing pin. ba 8K31Q99 �� $ 34.99 #080-540-127AU #30 .1270 5L2C99 $ 3.99 Nickel Silver 100-1400 14kt. White Gold 1825 #969-161-000AU Wolff Kit #1610, 9F25E99 ��$ 32.99 Silver 900-1200 10 kt. Yellow Gold 1665 #080-540-148AU #25 .1480 5L3G99 $ 4.99 Stainless Steel 1200 19 kt. White Gold 1975 NO. 15 #080-540-160AU #20 .1600 5L3Q99 $ 4.99 WOLFF COIL SPRING COMBINATION KIT - Kit #1610A Wire Diameters: .016" to .048" Length: 8". #080-540-172AU #17 .1720 5L4I99 $ 5.99 CARBON STEEL HEAT TREATING The same 50 springs in Kit #1607, plus 40 more. 2 each of 10 de- STRAIGHT SPRING WIRE - An excellent se- #080-540-175AU #16 .1750 5L3J99 $ 4.99 Colors vary slightly with steel analysis and length of time held at signs in both light and heavy weights. Length 2" (5.1cm) - 4" (10.2cm), lection of the wires needed to form most #080-540-197AU #8 .1970 5L3H99 $ 4.99 temperature. For details see GUNSMITH KINKS®. O.D.'s from 3/32" (2.4mm) to 1/4" (6.3mm). ba torsion and coil springs used in guns. 10 1 #080-540-250AU /4 .2500 5L4C99 $ 5.99 TEMPER COLORS #969-161-010AU Wolff Kit #1610A, 9F21P99 �� $ 27.99 pieces each of 18 different diameters, in poly bags with diameters marked. Kit contains di- Degrees Hardness ameters as follows: .016"; .018"; .020"; .022"; TOOL STEEL DRILL ROD - 18" Color F. Hardness Rockwell “C” NO. 69 O-1 OIL HARDENING DRILL ROD ROUND - .024"; .026"; .028"; .030"; .032"; .035"; .036"; Faint Yellow 420 Extra File Hard 63 Carbon - .95% Manganese - 1.20% Silicon - .25% Wire Diameters: .012" to .024" Coil O.D.'s from .110" to .210" .038"; .040"; .042"; .044"; .046"; .048". Supplied in 8" lengths. ba Light Straw 435 File Hard 62 1 COMPRESSION SERVICE SPRINGS - #969-101-500AU Wolff Kit #15, 9F26M99 ��$ 32.99 For /4" round and larger, we carry oil hardening drill rod rather Dark Straw 465 Knife Hard 60 Same outside diameters as in Assortment than water hardening. The O-1 in this size range is characterized by Yellow-Brown 490 Extra Hard 58 No. 71, but of softer action. Designed pri- good machinability, smooth finish as well as superior dimensional Purple 520 Hard 56 marily for locks, sporting equipment and BLITZPAK #15 - The same 18 diameters of top quality wires as in stability and excellent hardening characteristics. We recommend Dark BLue 570 Half Hard 53 the softer acting gun and camera springs. Kit #15 above, but only two pieces of each diameter are in this kit. it for use in dies, tools, parts, and punches. Excellent for general Cut to 12" lengths.ba 36 pieces total; no diameter identification. ba use in the shop. Blue-Gray 620 Spring Temper 50 #025-069-000AU No. 69 Spring Assort., 8K17B99 ��$ 18.99 #969-101-550AU Wolff Blitzpak #15, 9F8C99 �� $ 10.99 NO. 71 Wire Diameters: .016" to .058" Coil ALUMINUM ROUNDS O.D.'s from .095" to .312" STOCK # SIZE PRICE COMPRESSION GUN SPRINGS - Twelve Aluminum Alloys For Machining Strong, Lightweight Parts 3 #084-185-375AU /8" 5L18E99 $ 19.99 compression springs of medium to stiff View our How-To Video Guides at Heat-treated 6061-T6 aluminum alloy that offers a wide range 1 action. Two each of six sizes, 12" long. #084-185-500AU /2" 5L7E99 $ 9.99 of both mechanical properties and corrosion resistance. Easy to 3 #084-185-750AU /4" 5L13B99 $ 16.99 Will cover many gun and shop needs.ba brownells.com machine; has a maximum tensile strength of 35,000 psi. ab #025-071-000AU No. 71 Spring Assort., 8K21L99 �� $ 24.99 SPECS: 18" (45.7cm) long rods. #084-185-900AU 1" 5L38J99 $ 41.99

order on the web

Orders: 800-741-0015 brownells.com PAGE 381 RAMP SOLDERING JIG “FATIGUE PROOF” STEEL RODS GUNSMITH’S COIL SPRINGS STEEL SHIM STOCK Spring Pressure Keeps Ramps/ Bases/.45 Sights In Place Make Parts & In-Hole & Over-Pin Solves Most Put Them Right To Work; Styles “Need A Little More Metal” Problems Cures the “ramp slips just as the No Heat Treating Required solder melts” problem with a pointed, Finest quality coil springs, controlled-tension wound for For scope base adjustment, sight adjust- spring-loaded plunger that keeps con- Superior quality, high den- smooth operation without binding under compression. “Over-Pin” ment, head-space adjustment and checking, stant pressure on the ramp or a .45 sight. sity; very machineable and tough, springs are designed to function over gun pins and plungers; “In- restoration of misaligned parts oldering on Adjusts for height, angle and amount of without brittleness, due to a high Hole“ springs are made to fit inside restricted areas. ab for buildup, inletting templates, spacers. You spring pressure. Non-marring, “V” block ratio of manganese to carbon. SPECS: High tensile spring wire. 12" (30.5cm) long. name it, and somewhere along the line a shim can be used for ev- base centers barrel under the plunger. Does not require heat treating like erything from shimming, to measuring, to fixing! ab Great torch clearance. ab METAL WORK METAL ”OVER-PIN” KITS - 12 Coil Springs, 7 sizes, wound and sized to op- 1 low density mild steel - perfect for 2 SPECS: 2" (5.1cm) long. aluminum Base. 4" (10.2cm) high overall. 3 3 KIT NO. AC-24 - consists of one piece, each, steel shim stock, 2 / " spring guides, screws, firing pins, erate without binding over pins from /32" (2.4mm) to /16" (4.7mm). x 6" in the following thicknesses: .001" .002" .003" .005" .010" .015" #080-739-000AU Ramp Soldering Jig, 8K77G99 ��$ 89.99 12" long (30.5cm). Kit #1, OD-12; Light duty. Kit #2, OD-12; Heavy any parts that will be subject to shock or repeated stress. ab #080-544-024AU AC-24 Steel Shim Stk Kit, 8K14N99 ��$ 19.99 1 5 3 duty. SPECS: /4" (6.3mm), /16" (7.9mm), /8" (9.5mm) diameter. 18" (45.7cm) long steel rods. 6 rods per pak. Assortment contains 2 of each size. 140,000 psi #080-950-125AU Light Duty, Over-Pin Kit #1, KIT NO. AF-12 - consists of one piece, each, steel shim stock, 6" tensile strength, Rc 30-36. Tolerances are + or – .006" (.15mm). 8K16P99 �� $ 20.99 x 12" in the following thicknesses: .001" .0015" .002" .003" .004" 1 #080-531-250AU /4" Fatigue Proof Steel, 5L135D99 ��$ 143.99 #080-950-150AU Heavy Duty, Over-Pin Kit #2, .005" .006" .007" .008" .010" .012" .015" TIX SOFT SOLDER 5 8K16Q99 �� 20.99 #080-531-312AU /16" Fatigue Proof Steel, 5L63J99 �� 69.99 #080-544-012AU AF-12 Steel Shim Stk Kit, 5A53F99 ��$ 62.99 Melts At 275° F. For All Solderable Metals 3 #080-531-375AU /8" Fatigue Proof Steel, 5L121D99 �� 131.99 “OVER-PIN” MASTER KIT - Combines Kit #1 OD-12 and Kit #2 “Hardest soft solder on earth.” Melts at 275° F. Bond #080-531-000AU Asst. Fatigue Proof Steel, 5L114K99 �� 120.99 OD-12 for a total of 14 Coil springs for over-pin use. strength is 4,000 psi. For steel, gold, silver, stainless steel, #080-950-100AU Over-Pin Master Kit #3 OD-14, alnico, pewter, most alloys. Will not tarnish. Contains no 8K22F99 �� $ 27.99 silver or bismuth. Works beautifully for attaching pre- BRASS ROUNDS & FLATS cious metal inlays. Works best with TIX Flux. ab “IN-HOLE” KITS - 12 Coil Springs; 6 sizes made to function freely SPECS: 125 grains, approximately 3" (7.6cm) sticks. 3 1 100’s Of Uses inside holes from /32" (2.4mm) to /4" (4.7mm). 12" long (30.5cm). #030-001-125AU TIX Solder, 3K16L99 �� $ 17.99 Kit # 1, ID-12; Light duty. Kit #2, ID-12; Heavy duty. Free-cutting, half-hard 1 #030-002-050AU /2 oz. TIX FLUX, 3K3N99 �� 4.99 EXTRA-WIDE SPRING STEEL #080-950-325AU Light Duty, In-Hole Kit #1, brass in sizes suited to gun 8K16L99 ��$ 20.99 Two Widths & Four Thicknesses work and hobbies. Round As- 1 1 3 1 For Custom Springs & Parts #080-950-350AU Heavy Duty, In-Hole Kit # 2, sortment contains /8", /4", /8" and /2" diameter pieces. Some round 8K16Q99 �� 20.99 sizes available separately; see table. Flat Assortment contain one Big enough to make those wide each of the sizes listed. ab HOMOGENIZED SOLDER springs on new and old muzzle- “IN-HOLE” MASTER KIT - Combines Kit #1 ID-12 and Kit #2 ID-12 SPECS: 18" (45.7cm) long. loaders, double rifles and shotguns; for a total of 12 springs for in-hole use. Syringe Meters Exactly, 18" BRASS ROUNDS parts, too. ba #080-950-300AU In-Hole Master Kit Kit #3 ID-12, Locates Precisely 1 1 SPECS: 1095 cold rolled and annealed hi-carbon steel. /32" (.79mm), /16" 8K17L99 �� $ 20.99 STOCK # DIAMETER PRICE SPRINGS & RAW MATERIALS SPRINGS & RAW 3 1 1 Two solders-in-flux join most ferrous and non-ferrous metals, (1.6mm), /32" (2.4mm) or /8" (3.2mm) thick x 16" (40.6cm) long. Available #084-180-250AU /4" 5L16A99 $ 19.99 1 1 in /2" (12.7mm) or 1" (2.5cm) widths. /2" (12.7mm) Assortment: two pieces 3 including stainless steel. Exceptions are aluminum and magnesium. #084-180-375AU /8" 5L39F99 $ 45.99 Special homogenizing process ends solder/flux separation. Flux of each thickness. 1" (2.5cm) Assortment: one piece of each thickness. To 1 #084-180-500AU /2" 5L40A99 $ 48.99 harden: heat to 1450°-1500° F. and quench in oil. Yields Rc 66. residue cleans up with warm water. ab #084-180-004AU Brass Round Asst., 5L73I99 ��$ 91.99 SPECS: 70PA Solder: 16,000 psi tensile strength, 425° F. bonding temp. DRAW Rc PSI DRAW Rc PSI Great for joining dissimilar metals. Can be Plated Over with Electroless Nickel. 80PA Silver Braze: 85,000 psi tensile strength, 1125° F. bonding 400° F. 62 320,000 900° F. 41 189,000 BRASS FLATS MILD STEEL ROUNDS & FLATS temp. Excellent for nickel alloy, carbide and dissimilars. Can Be Plated 600° F. 55 270,000 1000° F. 38 176,000 STOCK # SIZE PRICE Over. 1 oz. (28 g) net wt. 1018 Steel In Handy Lengths & Sizes 1 1 700° F. 49 238,000 1100° F. 34 155,000 #084-181-250AU /4" x /2" 5L25H99 $ 29.99 #080-601-070AU 70PA Solder, 5L33E99 �� $ 39.99 1 800° F. 45 212,000 1200° F. 30 138,000 No more “Mystery Metals” from the junk yard. This quality 1018 #084-181-290AU /4" x 1" 5L36B99 $ 41.99 #080-602-080AU 80PA Silver Braze, 5L65E99 �� 79.99 3 steel is ideal for making shop projects. 18" lengths. Assortments #084-181-390AU /8" x 1" 5L36A99 $ 44.99 1 contain one piece of each size. ab #080-036-000AU /2" Spring Stock Assort., 8K30C99 ��$ 39.99 #084-181-000AU Brass Flat Assortment, 4H74M99 ��$ 81.99 1 1 #080-037-132AU 10 Pk /2"x /32" Spring Stock, 18" MILD STEEL ROUNDS 8K26C99 �� 30.99 STOCK # DIAMETER PRICE 1 1 HI-FORCE 44™ SOLDER #080-037-116AU 10 Pk /2"x /16" Spring Stock, 1 #080-735-250AU /4" 5L4I99 $ 5.99 8K20C99 �� 23.99 3 28,000 PSI - Flows At 475° F. 1 3 #080-735-750AU /4" 5L21C99 $ 24.99 #080-037-332AU 10 Pk /2"x /32" Spring Stock, MUSIC WIRE SPRING STOCK The Best All-Round Solder For Gunsmithing 8K50H99 �� 59.99 #080-735-900AU 1" 5L34A99 $ 37.99 1 1 Brownells Hi-Force 44 Solder is an alloy sol- 2 8 #080-735-000AU Mild Steel Round Assort., 5L73Q99 ��$ 79.99 Form Or Turn Your Own Special Springs SOLDERING & WELDING #080-037-018AU 10 Pk / "x / " Spring Stock, 8K53E99 �� 69.99 For Those Weird Ones der containing 4% silver and 96% tin. Excellent 18" MILD STEEL FLATS for steel, stainless steel, nickel, brass and copper. #080-038-000AU 1" Spring Stock Assort., 8K25G99 �� 32.99 1 /4 lb. rolls in a convenient “Tangle-Free” dispens- Completely non toxic. Flows free and smooth 1 STOCK # SIZE PRICE #080-038-132AU 4 Pk 1"x /32" Spring Stock, 8K27G99 �� 34.99 er for handy withdrawal of any length needed. ab at about 475° F., greatly reducing heating time. 1 1 1 1 #080-038-116AU 4 Pk 1"x /16" Spring Stock, 8K19C99 �� 22.99 #080-736-150AU /8" x /2" 5L17A99 $ 19.99 SPECS: Length varies. /4 lb. (113g). No need for cumbersome oxyacetylene setups. 3 3 1 #080-038-332AU 4 Pk 1"x /32" Spring Stock, 8K24I99 �� 31.99 #080-736-250AU /16" x /2" 5L8F99 $ 9.99 #715-212-020AU .020" Music Wire, 5A12Q99 ��$ 14.99 Prevents black oxide formation to reduce cleanup time. Provides 1 14,000 to 28,000 PSI tensile strength. Will not crack under stress as #080-038-018AU 4 Pk 1"x /8" Spring Stock, 8K33I99 �� 43.99 #080-736-000AU Mild Steel Flat AssorT., 5L132M99 �� $ 139.99 #715-212-045AU .045" Music Wire, 5A9G99 �� 10.99 do other low temperature soldering materials. And, a big plus . . . customers report that parts joined with Hi-Force 44 Solder showed no effects when immersed in hot bluing tanks! Use #4 Comet Flux. ab 1 7 SPECS: Wire - /16" (1.6mm) diameter. Ribbon - .015" (3.8mm) thick, /16" HOW TO MAKE A FLAT OR “V” SPRING (11mm) wide. The following method of spring tempering was the lifelong trade secret of John Frazier, Master Gunsmith of Chariton, Iowa. Of some 3,000 plus springs he made during his career, he knows of only three that broke. #080-649-001AU 1 oz. H/F 44 Wire, 5L8A99 �� $ 11.99 Heavy “V” springs are best forged and finish-filed, then ground to shape. Be SURE all lines are absolutely true and all tapers are similar to a “buggy whip”. Beyond the end of the taper of one leaf, leave part of the 1 #080-649-250AU /4 lb. H/F 44 Wire, 5L24P99 �� 30.99 original steel attached. Hold the spring by this while hardening to prevent the heat bleed-off caused if the spring itself were held with pliers. In a dark or unlighted corner of your shop, heat the spring until it just shows red color and quench. Now grind to exact shape and dimensions. Next, take a quart tin can and pound an indentation in one side, #080-649-100AU 1 lb. H/F 44 Wire, 8K97Q99 �� 110.99 deep enough to hold the spring. #080-649-301AU 1 oz. H/F 44 Ribbon, 5L7N99 �� 8.99 1 Place the spring in the indent and cover it with motor oil. Set the oil on fire and let it completely burn up. Then throw a handful of dry lime over the spring to “keep it dark” for a couple hours. The spring in now #080-649-325AU /4 lb. H/F 44 Ribbon, 5L25I99 �� 29.99 properly tempered. As John puts it: “You either have a spring or you don’t. A complete compression in your vise will darned soon tell you!” #080-649-390AU 1 lb. H/F 44 Ribbon, 5L100D99 �� 118.99

GUARANTEED. FOREVER.

PAGE 382 SINCE 1939 Office/Tech: 641-623-5401 WOLVERINE JOINING TECHNOLOGIES SOLDER BLACK HEAT-TREATING ACCESSORIES BLACK FLUX ® HI-TEMP HI-FORCE 44™ SOLDER 2 Solutions For Soft & Silver Solder, TEMPILAQ - For furnace or open flame hardening and High-Temperature Range; To Blend & Hide Solder Line tempering of steel parts. Apply thin smear to surface 38,000 PSI; Flows At 650° F. Highest to be treated. When desired temperature is reached, METAL WORK Recommended For Stainless Steel Silver-Bearing Content Of Any Non-Zinc Solder Blackens silver and soft solder joints, blends them Tempilaq melts sharply.ba High-quality paste flux has a working into bluing for a professional looking finish. Impervi- SPECS: 2 fl. oz. (59 ml) in brush top bottle. Higher tensile strength for a stronger bond on range of 1,100°–1800° F that’s perfect for ous to solvents and oils. ab joints that are subject to a high degree of stress or high-temperature silver solder applica- STOCK # DEGREE F. STOCK # DEGREE F. vibration. Contains 95% Cadmium and 5% Silver BROWNELLS SILVER SOLDER BLACK - For hi-temp tions. Specifically designed for use with #877-450-002AU 450 #877-145-002AU 1450 that flows free at 640° to 650° F. (maximum temp. Silvaloy 355 silver solder, Black Flux works silver solders like Silvaloy 355. #877-000-001AU 650 #877-150-002AU 1500 740° F.). Bonds quickly to all types of steel including particularly well on stainless steel and SPECS: 4 oz. (118 ml) bottle. stainless steel. Not affected by hot, caustic bluing solutions or by other refractory metals. Not for use on aluminum, magnesium, or #083-032-004AU Silver Solder Black, 8K12M99 ��$ 13.99 #877-700-002AU 700 baking after spray-finish applications. Use with Copper Bond Flux Titanium. Paste formula is easy to apply exactly where you need it; and adequate ventilation. ab BROWNELLS SOFT SOLDER BLACK - For soft solders like Hi- #877-200-000AU 2 oz. Tempilaq Thinner, 7A9I99 ��$ 10.99 1 cleans up with hot water. ab SPECS: Wire - /16" (1.6mm) diameter. SPECS: 8 oz. (227g) jar. Meets Fed. Spec 0-F-499 Type B, AMS 3411, AWS Force 44™. Will also color silver bearing solders but color may — Advise # — 2 oz. Tempilaq, 7A23G99 ��$ 24.99 #080-649-501AU 1 oz. Hi Tmp Hi-Force 44, 5L10N99 ��$ 14.99 FB3-C. ISO 9002 certified. rub to a medium gray. 1 SPECS: 4 oz. (118 ml) bottle. #080-649-525AU /4 lb. High Temp Hi-Force 44, #100-007-031AU Black Flux, 4B8Q99 �� $ 17.99 #083-032-014AU Soft Solder Black, 8K9A99 �� $ 11.99 STAINLESS STEEL HEAT TREAT FOIL 5L47I99 �� 54.99 - For scale-free, furnace heat treating #080-649-590AU 1 lb. High Temp Hi-Force 44, of tool steel without an atmosphere- 8K181A99 �� 202.99 controlled furnace. Make parts without COPPER BOND FLUX losing tolerances due to scale. Wrap part ACID BRUSH with foil, fold edges double and seal. Heat The Right One To Use With Brownells Hi-Temp, treat as usual. Open foil, remove part and Hi-Force 44™ Solder air cool or quench. Wear gloves; edges are very sharp! SILVALOY 355 SPECS: 24" (61cm) x 24" (61cm). .002" (.051mm) thick. Designed for soldering in the 600° F. to 800° F. Not Just For Soldering But A Host Of Other Uses #080-656-001AU SS Foil, 5L18B99 ��$ 21.99 SILVER SOLDER range, making it ideal when you’re working with Hi- Temp, Hi-Force 44. Flows easily into tight spots, cleans This old standby, the original tinner’s acid brush, will also handle Now Color Matches To Stainless Steel; up with warm water. ab the 1,001 other odd shop jobs that call for a handy, inexpensive TOUGH-QUENCH™ QUENCHING OIL - Gives pre- 56% Silver; Cadmium-Free SPECS: 6 fl. oz. (177 ml) bottle. brush. Spread glue, brush on stain, apply solder flux, clean out an dictable, controlled, fast quenching speed for uni- action, slap on oil or grease, brush metal filings from cutting tools Silvaloy 355 is recommended for #478-100-100AU Copper Bond Flux, 8G19N99 �� $ 24.99 form hardness. Wets out work rapidly, prevents for- - you name it. mation of gas pockets. Less smoke, low rate of heat joining steel, stainless steel, copper, copper alloys, nickel, nickel al- 3 SPECS: Rolled tin handle, bristles tightly crimped; 2 sizes: #1 - /8" (9.5mm) transfer to minimize distortion and cracking of the 9 loys and precious metals to themselves or any combination of these. and #3 - /16" (14.3mm). 6" (15.2cm) long. Has the lowest flow temperature, best wetting and best flow char- steel. Can be shipped UPS. #080-001-024AU #1 Acid Brush, 2 dozen, 8K6A99 �� $ 7.99 acteristics of any cadmium-free, high silver-content, commercial SPECS: 1 qt. (16 fl. oz./946 ml), 1 gal. (128 fl. oz./3.8 L) in silver solder. Highly recommended for all silver solder jobs where #080-001-144AU #1 Acid Brush, 1 gross, 8K17F99 �� 18.99 cans. Flash point is 355° F. (179.4° C.); Fire point is 410° F. sheet or flow method is desired. A “must” for installing sights and NO. 4 COMET FLUX #080-003-024AU #3 Acid Brush, 2 dozen, 8K5I99 �� 6.99 (210° C.). #083-027-032AU 1 Qt. Tough-Quench, 5L15N99 ��$ 18.99 ramps on stainless steel guns since the almostwhite color matches Makes Solder Flow Smoothly; #080-003-144AU #3 Acid Brush, 1 gross, 8K28L99 �� 32.99 stainless steel beautifully. Use with Ultra Flux®. ab #083-027-128AU 1 Gal. Tough-Quench, 5L50P99 �� 59.99 SPECS: Melts at 1145° F., flows at 1205° F. 56% silver. Gives Even, Professional Job STOCK # QUANTITY LENGTH PRICE Improves solder jobs by promoting smooth, even, NON-SCALING COMPOUND - Saves hours of solder flow that results in stronger, professional looking .005(.13MM) RIBBON rework time - parts can be made to exact dimen- solder joints. Special wetting agents assure total coverage sions before heat treating without fear of dimension 5L85J99 #080-538-305AU 1 ounce (28.3g) 74" (188.0cm) $ 109.99 of work. Works fast, eliminates need for pre-cleaning. Use change from scaling, pitting, decarb loss. Simple to SOLDERING & WELDING 1 3½% NICKEL STEEL WELDING ROD #080-538-405AU /2 ounce (14.2g) 37" (94.0cm) 5L39G99 $ 54.99 with Brownells Hi-Force 44™ and other solid core solders use - for both hardening or annealing. Heat the work 1 /32" (.79MM) ROUND WIRE on all metals except aluminum. No-spill application. ab Blues Beautifully; No Blow Holes; piece to about 500° F., coat with the dry compound #080-538-332AU 1 ounce (28.3g) 20 ft. (609.6cm) 5L50A99 $ 60.99 SPECS: 6 fl. oz. (177 ml) plastic squeeze bottle. Smoother, Nicer Welds powder, finish heating to temperature, and quench/ 1 #478-100-004AU No. 4 Comet Flux, 8G19F99 �� $ 20.99 cool as required. Parts come clean in boiling water. #080-538-432AU /2 ounce (14.2g) 10 ft. (304.8cm) 5L24M99 $ 29.99 This product will damage or remove bluing. Developed for use in our space SPECS: 1 lb. (454 g). Not for steels that harden above 1650° F. program to give the best possible #083-015-100AU Non-Scaling Compound, 5L21F99 �� $ 24.99 1 welds, 3 /2% Nickel Steel Welding Rod is almost totally free of impurities and flows beautifully to produce an extremely smooth, non-porous weld with Oxy-Acetylene FLUXED HI-FORCE 44™ or TIG. Over the years many gunsmiths have asked for this rod to Handy, Pre-Fluxed Saves Time, Mess FOR THE PRACTICAL GUNWORKER weld bolt handles and other items that will be polished after welding. Thanks to Jim Thompson, Maverick Gun Works of Topeka, Kansas, The same super-strong, easy-han- 1 SILVER SOLDER PASTES we’ve located a supplier of 3 /2% Nickel Steel Welding Rod. dling mixture as Hi-Force 44 but with its 1 Says Jim, “I finally located some 3 /2% Nickel Steel Rod and the SURFACE HARDENING COMPOUND own “Blitz” flux right in the core of the In Quickly-Applied Paste Form first bolt I welded was perfect. The rod is expensive but worth its wire. ab weight in gold when you are welding bolt handles and any other job Produces A Super Hard Surface On Plain & SPECS: 1.6 oz. (45 g) spool. FUSION solders come already ground in their where a perfect weld is desired. I find I get the best results as follows: Low Carbon Steels #080-649-110AU Fluxed Hi-Force 44, 8K16J99 �� $ 20.99 own special flux in the right proportions. Note: Man- ufacturer sometimes packages product in a large jar than required bring parts to welding temperature with a rather large flame, then to hold the product. Weights given here are the actual amount of back off on the flame until it is just hissing. I use a No. 2 tip. (You might Easy-to-use compound case hardens product you will receive. ab find another works better.) Take your time, don’t get it too hot and plain and low carbon alloy steels. Carburizes you can work with it all day if you have to. The weld is easy to work surfaces quickly to uniform depth while re- ® STL 1205 SILVER BRAZE - Lowest temperature, high strength with, file or machine. Be sure to use a neutral flame.” taining the toughness of the core. Also pro- ULTRA FLUX brazing alloy. For tight fitting joints, with minimum amount of fill. SPECS: Each piece is approximately .094" (2.4mm) or .045" (1.14mm) tects delicate, highly finished work, and helps Use on ramps or ribs where the fit is very close. diameter, - 12" (30.5cm) long. Sold in 4 oz. (113 g), 8 oz. (227 g) and 1 eliminate the need for remachining. Simply Paste Flux For Silver Solders HEAT-TREATING SPECS: Melts at 1145° F. 1 oz. (28 g) jar. lb. (454 g) paks. apply the hardening compound to your metal parts, heat to the Designed specifically for use with silver sol- #322-100-650AU STL 1205 Braze, 2B74K99 �� $ 77.99 #080-547-025AU 4 oz. .094" Welding Rods, 8K20P99 �� $ 24.99 required temperature, then quench in oil or water for a professional ders like Silvaloy 355. Protects the work piece #080-547-050AU 8 oz. .094" Welding Rods, 8K29D99 �� 34.99 grade, heattreatment. Helps keep the edge sharp on expensive drill STL 1260 SILVER BRAZE - Use when putting on front ramps that do bits, milling and grinding tools, punches, firing pins, hammer davits, and improves the flow characteristics of solder. #080-547-100AU 1 lb. .094" Welding Rods, 8K53C99 �� 59.99 Creamy texture applies easily with brush, resists not fit contours of barrel perfectly. Also used for joining small parts trigger pins, sears, and cocking pieces. Water soluble for easy clean- drying and caking. Works up to 1600° F. on all where chips of steel have been broken or where it is impossible to #080-547-104AU 4 oz. .045" Welding Rods, 8K25Q99 �� 29.99 up. Complete instructions included. ab metals except aluminum, magnesium and titanium. ab hold parts “absolutely together” for brazing. #080-547-108AU 8 oz. .045" Welding Rods, 8K35I99 �� 39.99 SPECS: 1 pound (453.6g) can. 1 SPECS: /2 lb. (227 g). Meets Fed. Spec OF499, Type-B, AMS 3410. SPECS: Melts at 1220° F. 1 oz. (28 g) jar. #080-547-110AU 1 lb. .045" Welding Rods, 8K56A99 �� 59.99 #083-000-033AU Surface Hardening Compound, #080-538-050AU Ultra Flux, 4B11B99 �� $ 14.99 #322-120-650AU STL 1260 Braze, 2B68J99 �� $ 80.99 5L18N99 ��$ 21.99

order on the web

Orders: 800-741-0015 brownells.com PAGE 383 MARVELUX® BULLET CASTING FLUX HEAT STOP™ HEAT CONTROL PASTE COLOR CASE HARDENING KIT HEAT-TREAT THERMOMETER Non-Smoking, Non-Fuming Keeps Heat From Spreading When Produce Beautiful Color Case Positive Temperature Control For Odorless Flux Welding, Soldering or Brazing Hardening Like The Pros Lead, Heat-Treat Baths Far and away the most popu- Fantastic compound prevents heat trans- The subtle shades of blue, Easy, positive way to know that lar - and successful - bullet cast- fer so effectively you can heat one end of a gray, and straw on color case you have the casting pot operating ing flux, MARVELUX has been on steel bar red hot - while holding the other end parts give a gun a true custom at ideal temperature for perfect cast the market since 1971 filling the in your bare hand! Absorbs heat that would look. Cowboy Action Shoot- bullets each time. Makes a cheap pot needs of knowledgeable and suc- cause adjacent parts damage during welding, ing has brought many guns out as accurate as the expensive ones. ab cessful professional and hobbyist brazing, heat treating and soldering. One of of retirement that need to have SPECS: 2" (5cm) dial, 8" (20.3cm) long stem, .150" (3.8mm) diameter (im- METAL WORK METAL bullet casters. MARVELUX is non- the greatest chemical developments ever for faded colors restored. We’ve merse at least 2" (5cm) in liquids). 304 stainless. Rustproof, dustproof, 1 corrosive to iron and steel, and does not produce fumes which can the gunsmith. For welding bolt knobs, shortening actions, installing assembled two, easy-to-use leadproof, hermetically sealed. Guaranteed accurate to /2 of 1% around cause corrosion, as does sal-ammoniac (ammonium chloride). In ramps and sights, plus all milling and grinding operations where it systems with all the items you entire dial range. Uses bi-metallic helix coils - Range is 200° - 1000° F in fact, regular use will keep your pot free from rust! Reduces dross protects expensive, hard-to-replace drill bits and cutters, as well need to immediately begin a 10-degree increments. Recommended for continuous use below 800° formation dramatically while increasing fluidity of bullet alloys, mak- as the gun. Odorless, non- toxic, no fumes, won’t harm skin, won’t case color hardening operation F.; intermittent use above 800° F. ing it easier to obtain well filled-out bullets. MARVELUX is well suited stain surfaces applied to, won’t melt or run, and cleans up easily (except a quenching tub). Complete system includes our 1.37 cu. ft. #084-069-225AU Lead Thermometer, 4K35C99 ��$ 39.99 to any lead alloy intended for casting bullets or swaging cores. Non with water. heat treat furnace, 11" x 4" cylindrical crucible big enough for a rifle smoking, flameless and non-smelling. Superior to beeswax, tallow, During welding, HEAT STOP™ does not interfere with the weld action, 30" long crucible tongs for handling ease and safety, Kevlar paraffin, and other grease-type fluxes. Even better than rosin and it joint in any way; will not splatter. Greatly simplifies welding of dis- gloves for protection against high temps (also sold separately), a full doesn’t smell like you’re burning down an old shed. ab similar materials. Acts as an anti-flux during soldering to prevent face shield to protect your face, 10 pounds of high carbon content 1 SPECS: Available in /2 lb. (227 g), 1 lb. (454 g) or 4 lb. (1.8 kg) jar. Carton solder sticking to the wrong things or surfaces. Cuts heat-up time wood charcoal, 25 pounds of high carbon content filler-free bone POLISHING GLOVES 1 contains 12, /2 lb. or 12, 1 lb. jars. tremendously. Best protection against flame damage to wood, tape, charcoal, five disposable filter masks to keep dust out of your lungs, 1 Stop Rust-Causing Fingerprints #083-030-050AU /2 lb. MARVELUX, 5L6E99 �� $ 9.99 putty, formica, plastic, glass, paper, rubber, metal, chrome, paint, a long shop apron, and complete instructions explaining the color #083-030-100AU 1 lb. MARVELUX, 5L11H99 �� 15.99 electrical wiring and fabrics. Used by emergency crews to protect case hardening process. Kit Without Furnace has the same, large Cotton canvas gloves keep finger- #083-030-400AU 4 lb. MARVELUX, 5L33N99 �� 46.99 crash victims who must be cut out of wreckage with acetylene capacity crucible, charcoal, and supplies, only without the furnace, prints off freshly polished steel, and 1 torches. for those who already have a heat source capable of heating the keep your hands clean while polishing, #083-030-052AU 1 Carton, /2 lb. MARVELUX, Try it - we promise you’ll become a believer that very first time. crucible to 1,450° F. ab too. Stretch knit cuff for stay-in-place fit. 3H85N99 �� 102.99 Comes as close to pure “magic” as any product we’ve found. ab #100-011-091AU Case Hardening Kit w/Furnace, SPECS: Industrial cotton, off-white. Sold in pak of 6 pairs only. #083-030-102AU 1 Carton, 1 lb. MARVELUX, SPECS: 1 lb. (454 g) net weight. 3Z2077G99 �� $ 2358.99 #599-000-001AU Polishing Gloves, 6 Pr., 9E10I99 �� $ 17.99 3H141Q99 �� 189.99 #083-012-100AU Heat Stop, 5L14B99 ��$ 16.99 #080-951-501AU Case Hardening Kit w/o Furnace, 8K437D99 �� 543.99 POLISHING #494-666-160AU Hi-Temp Gloves, 4D72C99 �� 75.99 *Note: Shipped Truck only. Please call for freight charges. POLISHING WHEEL CLEANING BRICK

ATP SUPLLY CO., INC. COLOR CASE HARDENING CRUCIBLE & TONGS - If you already Restores Polishing & Buffing Wheels EVENHEAT KILN have a furnace, these two tools will make the job easier. Crucible ANTI SCALE COATING - 138 cu. in. of space lets you color case harden a rifle action or Crystolon block quickly knocks off the HT-1 HEAT TREAT OVEN large revolver frame with space for the necessary blocking. Round old caked-on, used-up abrasive and residue Eliminates Scaling shape is easy to handle with no wasted corner space. Clamping from the surface of muslin, felt and grind- Programmable For ing wheels. Liquid anti-scale compound can be sprayed, rings position the canister securely in the tongs when carrying and Hands-Off Heat-Treating dumping. Tongs - 30" long handles keep you back, away from SPECS: 2" (5cm) high x 2" (5cm) wide x 4" flow coated, brushed or dipped onto parts to & Color Case-Hardening (10.1cm) long. minimize the formation of oxide scale and dras- the furnace heat, makes grabbing the hot crucible safer and more secure. #657-024-000AU Wheel Cleaning Brick, 7E00AJE ��$ 32.99 tically reduce pitting, decarb loss, cuts down on rework time, too. Programmable oven Has a hot working range of 1000° to 2300° Fahrenheit, crumbles on SPECS: Steel. Crucible - 11" (28cm) high, 4" (10cm) diameter. Tongs - 30" makes easy work of any (76cm) long. cooling, and parts rinse clean in hot water. ab heat-treating job, includ- SPECS: 1 pint (16 fl. oz./473ml). Set furnace between 1000° to 2300° F ing color-case hardening. #080-951-000AU Crucible, 8K96Q99 ��$ 113.99 for best results. Compact chamber is the #080-951-100AU Tongs, 8K81G99 �� 99.99 BUFFING WHEEL RAKE #100-002-607AU Anti Scale Coating, 6B15C99 �� $ 17.99 right size for receivers, bottom metal, buttplates, knife blades, cus- #080-951-200AU Crucible & Tongs, 8K142P99 �� 159.99 Fast, Efficient Truing Of tom screws, and other small parts. Numerical control with extra- large keypad lets you create and store up to 12 repeatable custom SMALL COLOR CASE HARDENING CRUCIBLE - Ideal choice for Felt & Muslin Wheels programs for consistent results. You determine the temperature small parts. Fits small furnaces and only requires 27 cubic inches Seen in use at a major ranges, hold-time, alarm set-points, and make easy on-the-fly of bone per session to save you money on small jobs. Perfect for arms maker, designed specifically for truing felt and muslin wheels. NEYTECH adjustments to fine tune your program. Even allows you to pre- rings, slide stops, bolts, and much more. Far easier to use and more effective than the traditional wood rasp; a 1 3 program the start time to take advantage of variable electric rates. SPECS: Steel. 5 /2" (14cm) high, 3 /4" (9.5cm) diameter wheel trued with this rake will literally “suck-up” the polish. No need MANUAL CONTROL FIBER FURNACE Backlit, four character display provides accurate real-time tem- #080-951-001AU Small Crucible, 8K79H99 �� $ 99.99 to hand clip the threads on a stitched wheel before truing, the Rake perature/time monitoring. Cool-touch door handle allows com- 1 does that for you. The wood handle gives a solid, two-hand hold and Chamber - 9" x 6 /2" x 9" Temperature fortable operation when the oven is hot. Innovative safety interrupt light pressure with just two of the four rows of aggressive, steel teeth Range - 1400 Watts 300-2000° F. automatically removes power from all heating elements when the makes quick work of wheel imperfections. Simplifies reshaping of door opens and reapplies power after it closes. Built with a durable, State-Of-The-Art Insulation For Fast wheels for special jobs. ab corrosion-resistant stainless steel outer shell and a firebrick lining 1 1 SPECS: 15 /4" (38.7cm) lg. Cutting face is 4 /2" (11.4cm) long x 2" (5cm) wide. Heatup, Efficient Operation, Low Cost for maximum heating efficiency. Includes Type-K thermocouples 13 Wood handle is /16" (20.6mm) thick. for quick and reliable temperature control. Optional Loud Alarm Latest insulation technology makes #082-077-001AU Buffing Wheel Rake, 2H29K99 �� $ 34.99 sounds at 80+ decibels to cut through your shop noise and alert HEAT-TREATING CHARCOAL these furnaces a superior value. You get 3 you when the heat-treat process is over and it’s time to quench. #082-077-002AU Replacement Rake Teeth, 2H12E99 �� 15.99 times as much interior space and use 25% Also lets you know when initial hold temperature has been reached. Produces Dramatic Color & Swirl Patterns less energy in an outside cabinet that’s only For ovens with serial numbers over #107120. Comes with mounting 20% bigger than comparable, brick-lined Wood and bone charcoal with just the right hardware. ab furnaces. Fast heatup, about 10 minutes from room temperature sieve size for crucible packing of steel parts to SPECS: Stainless steel, natural finish, firebrick liner. External Dimensions be hardened. Hi-carbon content without wax- SCREW HEAD POLISHING VISE to 1000° F. Four-wall heating for even distribution. Side swing door. 1 - 18 /2" (47cm) long, 26" (66cm) wide, 27" (69cm) high w/legs. Internal es or fillers gives brilliant color patterns. Mixing Pilot light indicates heating. Non-slip rubber feet. Accurate, dual 1 1 Dimensions - 13 /2" (34.3cm) long, 13" (33cm) wide, 13 /2" high. 94 lb. (57kg) Polish Screws & Pins Safely F./C. Pyrometer has armored thermocouple. Single dial temperature types by specific ratio provides additional con- weight. Maximum Temperature: 2,000° F (1,093° C). Current Draw - 18 rate and set control. UL and CSA approved. Special thanks to the trol over color and pattern. ab Superior way to hold screws and pins amps 240 volts AC, 4320 watts. UL approved heating elements. folks at Price Hill Gun Shop, Cincinnati, Ohio. ab SPECS: Packed in 5 gal. bucket. Bone - 10x28 sieve when polishing heads. Prevents burned fin- 1 1 1 SPECS: 15 /2" (39.4cm) long x 15 /4" (38.8cm) wide x 16 /2" (42.0cm) high #100-004-956AU Heat Treat Oven, 3Z1475H99 �� $ 1669.99 size, 25 lb. (11 kg) weight. Wood - #6 size. 10 lb. (4.5 kg) weight. gers. Screws won’t be snapped out of grip by wheel and “lost” in shop. 3 1 overall. 526 cu. in. inside. 115/120v/60hz/12 amps. #100-015-271AU Evenheat Oven Loud Alarm, #084-097-031AU Bone Charcoal, 5L113N99 ��$ 119.99 SPECS: 5 /4" (14.6cm) overall. /4" (6.35mm) max. cap. #646-949-120AU 115v Fiber Furnace, 6D1163D99 �� $ 1288.99 3Z46Q99 �� 64.99 #084-098-013AU Wood Charcoal, 5L37G99 �� 43.99 #345-093-000AU Screw Polishing Vise, 5D12E99 �� $ 13.99 HEAT-TREATING GUARANTEED. FOREVER.

PAGE 384 SINCE 1939 Office/Tech: 641-623-5401 BALDOR BUFFERS SANDING BELTS Large Ball Bearings Industrial Quality Used By The Professionals Popular Sizes & Grits SCREW HEAD POLISHING/PIN VISE Tough, aluminum oxide grain, Heavy-duty, U.S. Made, construction stands up to the toughest shop use. We recommend the No More Burnt Fingers Or bonded to strong drill cloth with special, hi-temp METAL WORK one-horsepower 1800 rpm motor for the gun refinisher. Add the heavy Buffer Pedestal shown below Lost Screws & Pins Resinal. Gives excellent finish, resistant to dulling, runs for the ideal setup. All single phase Baldor Buffers come internally wired for 115 Volt, 60 cycle.- Easily cooler. Particularly suited for metal finishing. 1 Steel vise securely holds screws and pins in place during polish- changed over to 230 Volt (except /4 hp.). NOTE: Cord and Plug NOT included. ab 1 3 7 5 3 3 1 ing to prevent them from flying into the far corners of your shop. SPECS: /2" (12.7mm), /4" (10.9mm), /8" (22.2mm), 2 /8" (6.7cm), 6 /8" (16cm), 7 /16" (18cm), 16 /8"(41cm), 27" Totally Enclosed STOCK # GRIT PRICE STOCK # GRIT PRICE Knurled collar tightens evenly, without crushing. (68.6cm), 30" (76cm). Motor 1" (2.5CM) X 30" (76CM) 2" (5.1CM) X 72" (182.9CM) SPECS: Steel vise and collar, plastic handle. 4.75" (12cm) long. SHAFT EXT. OVERALL SANDING BELTS SANDING BELTS #080-000-316AU Screw Head Polishing/Pin Vise, SPEED ARBOR FROM SHAFT #925-130-036AU 36 5B3D99 $ 5.99 #925-272-036AU 36 5B8G99 $ 12.99 6A19G99 �� $ 22.99 STOCK # HP RPM DIA. END PLATE LENGTH PRICE #925-130-080AU 80 5B3N99 $ 4.99 #925-272-060AU 60 5B7I99 $ 10.99 1 1 5 1 #089-114-332AU /4 1800 /2 2 /8" 16 /8" 9H370N99 $ 389.99 #925-130-120AU 120 5B3F99 $ 5.99 #925-272-120AU 120 5B6G99 $ 9.99 3 3 3 #089-332-000AU /4 1800 /4 6 /8" 27" 9H664Q99 $ 699.99 #925-130-220AU 220 5B3Q99 $ 6.99 #925-272-220AU 220 5B6B99 $ 9.99 7 3 #089-407-000AU 1 1800 /8 7 /16" 30" 9H949Q99 $ 999.99 #925-130-320AU 320 5B3Q99 $ 6.99 #925-272-400AU 400 5B6P99 $ 9.99 CLYMER BARREL SPINNER #925-130-400AU 400 5B3L99 $ 5.99 #925-272-500AU 500 5B6N99 $ 9.99 BUFFER PEDESTAL - Heavy, stable pedestal keeps buffer perfectly steady and gives 360° access to both polishing wheels for best pol- 1" (2.5CM) X 42" (106.7CM) 4" (10CM) X 36" (91CM) ishing results. Exposes both shafts for full 360° polishing on all parts of guns, including barrels and receivers. Holds all Baldor Buffers. 3 1 SANDING BELTS SANDING BELTS SPECS: Cast iron. 33" (83.8cm) high. Base 13 /4" (34.3cm) x 15 /2" (39.4cm). Top plate is 9" (22.9cm) square. #925-142-036AU 36 5B3P99 $ 5.99 #925-436-080AU 80 5B8I99 $ 12.99 #089-001-000AU Baldor Buffer Pedestal, 9H372Q99 �� $ 419.99 Save Polishing Time, Prevent Ripples & Flat Spots #925-142-060AU 60 5B3I99 $ 5.99 #925-436-120AU 120 5B8G99 $ 12.99 Fastest way to polish barrels and magazine tubes with no ripples #925-142-080AU 80 5B3D99 $ 5.99 #925-436-220AU 220 5B8A99 $ 12.99 or flat spots. Cheaper and easier to use than a lathe. Just secure the #925-142-120AU 120 5B3B99 $ 6.99 #925-436-320AU 320 5B8N99 $ 12.99 barrel between the non-marring, Delrin® centers, turn on the buf- #888 POLISHING ARBOR & PILLOW #925-142-220AU 220 5B3G99 $ 5.99 #925-436-400AU 400 5B8B99 $ 12.99 fer, and touch the barrel to the buffing wheel or Scott Murray drum. WHAT DO I NEED TO POLISH GUNS? Here’s a quick look at the basic supplies for polishing guns. #925-142-320AU 320 5B3I99 $ 6.99 6" (15.2CM) X 48" (121.3CM) As the barrel spins, slide it across the wheel, varying the angle and BLOCKS POLISHING pressure to get the best cut. ab BASIC EQUIPMENT #925-142-400AU 400 5B3B99 $ 6.99 SANDING BELTS Add Grinding & Polishing Wheels SPECS: Extruded aluminum. Frame - 36" (91.4cm) long, 1" (2.5cm) square. First, you need something to turn the wheels. You can use salvaged elec- #925-142-600AU 600* 5B6J99 $ 8.99 #925-648-060AU 60 5B17E99 $ 21.99 Accepts 32" (81.3cm) barrels. Spinner Centers - Delrin, replaceable. Sup- To Your Shop tric motors from a variety of machinery but we like the 1800 RPM BALDOR #925-648-080AU 80 5B14L99 $ 18.99 1 7 1 2" (5.1CM) X 48" (121.9CM) port Arms - 4 /2" (11.4cm) x 1 /8" (4.8cm), socket head lock screws. 1 /2" Put electric motors to use for grind- BUFFER - It’s the number one choice of professional bluing and plating shops. SANDING BELTS #925-648-120AU 120 5B16A99 $ 20.99 (3.8cm) swing. ers, buffers, and wheels. #888 for wheels The long shafts get the wheels away from the motor body for good clearance. #925-248-036AU 36 5B6D99 $ 9.99 #925-648-220AU 220 5B14Q99 $ 18.99 #184-020-000AU Std Barrel Spinner, 4H146M38 ��$ 146.38 mounted above bench. #330 lets wheels As in cars, more horsepower is always better. It lets you turn a bigger wheel #925-248-060AU 60 5B5Q99 $ 8.99 #925-648-320AU 320 5B16I99 $ 20.99 #184-020-002AU Std Bbl Spinner Centers, 4H18H00 �� 18.00 overhang sides. ab which has a higher surface speed and, therefore, polishes faster. 1 SPECS: Aluminum alloy base, Sintered bronze bearings. Shaft 7 /2" You can bolt the buffer directly to a bench or table but that can limit ac- #925-248-080AU 80 5B5D99 $ 7.99 #925-648-400AU 400 5B14E99 $ 18.99 1 3 (19cm) long. 4 /2" (11.4cm) above base; 1 /4" (4.4cm) enclosed pulley. cess around the wheels for odd shaped objects. Our choice for a rock solid #925-248-120AU 120 5B5H99 $ 7.99 1 5 /2" (12.7mm) RH and LH threaded ends on /8" (15.9mm) dia. steel shaft. mount would be the BALDOR BUFFER PEDESTAL. #925-248-220AU 220 5B5P99 $ 7.99 #177-800-888AU #888 Polishing Arbor, 7G37B99 ��$ 39.99 6" or 8" STITCHED MUSLIN POLISHING WHEELS - The workhorse #925-248-320AU 320 5B5Q99 $ 8.99 wheel of polishing. Use for cleaning and/or roughing with the coarser grits. LONGRIFLES BARREL SPINNER 1 5 2 8 5B5M99 ATTACHMENT ARBOR - Converts any / " or / " You’ll need three wheels per grit (glue them together with Elmers, etc.). Power #925-248-400AU 400 $ 8.99 shaft electric motor into a polishing/grinding unit. 1 3 Billet Aluminum Construction ⁄2 ⁄4 1 5 the 6" with hp motors; a or 1 hp will turn the 8" nicely. SPECS: 3" (76.2cm) OAL for /2" (12.7mm) and /8" (15.9mm) Gives Long Service Life 3 1 6" or 8" LOOSE MUSLIN POLISHING WHEELS - Softer touch for that shafts. Both accept wheels up to /4" (19.1mm) wide with /2" arbor holes. final polish with the finer grits. The 90 ply wheel is wide enough for most Die cast. RH thread. Precision lathe arms for pol- work without stacking. SANDING BELTS 1 ishing barrels are machined from 2 #177-606-012AU / " Attachment Arbor, 7G6G99 �� $ 7.99 POLISHES high-grade billet aluminum, so 5 #177-606-058AU /8" Attachment Arbor, 7G6C99 �� 7.99 To Fit Raytech Expanding Sanding Drums they won't crack and fail under Of course, you’ll need polishing compound and our POLISH-O-RAY™ heavy use. Delrin centers have greaseless polishing compound is made with uniform, screened, mesh size Resin bonded, aluminum oxide. Sold singly. O-rings to prevent them from grit for very best results. Except for mirror finishes and aluminum work, P-O-R falling out of the inner-bearing will do it all. For mirror finishes on steel and soft metals like aluminum and STOCK # GRIT SIZE PRICE 1 15 race. Centers are beefy enough brass, our grease-base, NO. 555™ POLISHES are the best choice. Far easier #925-118-060AU 60 1 /2" (3.8cm) x 18 /16" (48.1cm) 5B3G99 $ 4.99 to work with than tripoli and rouge. 1 15 to withstand extensive use, and ex- SANDING DISCS #925-118-080AU 80 1 /2" (3.8cm) x 18 /16" (48.1cm) 5B3I99 $ 5.99 tra material on the taper side allows 1 15 Fast Off/On Disc & Grit Change ADDITIONAL HELPFUL TOOLS #925-118-120AU 120 1 /2" (3.8cm) x 18 /16" (48.1cm) 5B3P99 $ 5.99 them to be resurfaced. Spinner ac- When you first mount the new wheels, they will be out of round. In that 1 15 #925-118-220AU 220 1 /2" (3.8cm) x 18 /16" (48.1cm) 5B3L99 $ 5.99 cepts any standard 1" rectangular steel or aluminum tube to allow Resinal Metalite Pressure-Sensitive Discs condition they won’t “take” compound evenly and will bounce when you 1 15 #925-118-320AU 320 1 /2" (3.8cm) x 18 /16" (48.1cm) 5B3A99 $ 5.99 easy use with a polishing wheel. Quick-release handle for fast, easy lay flat for longer life. Resists disc clogging. touch the work to them. True them using the BUFFING WHEEL RAKE. As you 1 15 removal from lathe. ab For coarse-to-fine metal finishing and all polish and remove metal, the wheel surface will load up with metal particles #925-118-400AU 400 1 /2" (3.8cm) x 18 /16" (48.1cm) 5B3K99 $ 5.99 wood finishing. Sold in 3-Paks. ab 1 15 #100-014-492AU Barrel Spinner, 7B164J99 ��$ 173.99 and quit cutting efficiently; clean it and get it ready for fresh polish using the #925-118-600AU 600* 1 /2" (3.8cm) x 18 /16" (48.1cm) 5B5H99 $ 7.99 1 STOCK # DISCS PRICE POLISHING WHEEL CLEANING BRICK. #925-225-060AU 60 2" (5cm) x 25 /2" (64.8cm) 5B3M99 $ 5.99 1 6" (15.2CM) STUFF YOU WON’T WANT TO BUY, BUT REALLY NEED #925-225-080AU 80 2" (5cm) x 25 /2" (64.8cm) 5B3Q99 $ 5.99 1 #925-060-220AU 220 5B5P99 $ 8.99 Protect your eyes from flying grit and airborne particles by always wear- #925-225-120AU 120 2" (5cm) x 25 /2" (64.8cm) 5B3K99 $ 5.99 ing a FULL FACE SAFETY SHIELD. 1 RAYTECH SANDING DRUM 8" (20.3CM) #925-225-220AU 220 2" (5cm) x 25 /2" (64.8cm) 5B3C99 $ 5.99 3M DISPOSABLE FILTER MASKS - Helps keep harmful polishing dust 1 #591-080-060AU 60 1E8E99 $ 11.99 #925-225-320AU 320 2" (5cm) x 25 /2" (64.8cm) 5B3C99 $ 5.99 out of your lungs. Blow your nose after a session without wearing one, if you Expandable Drum Makes Grit Changes Quick & Easy 1 #591-080-080AU 80 1E8N99 $ 11.99 get black stuff, you need a mask. #925-225-400AU 400 2" (5cm) x 25 /2" (64.8cm) 5B3D99 $ 5.99 1 Steel drum with resilient rubber rim allows fast, #591-080-120AU 120 1E8F99 $ 11.99 #925-225-600AU 600* 2" (5cm) x 25 /2" (64.8cm) 5B6A99 $ 9.99 7 easy grit changes by stopping the machine, slipping #591-080-220AU 220 1E7D99 $ 10.99 #925-325-060AU 60 3" (7.6cm) x 25 /32" (64cm) 5B4D99 $ 7.99 off the old belt, and sliding on a new one. Angled 7 #591-080-320AU 320 1E8F99 $ 12.99 #925-325-080AU 80 3" (7.6cm) x 25 /32" (64cm) 5B4M99 $ 7.99 slots in the heavy rubber rim expand during rotation to anchor the 7 finishing belt in place for no-slip sanding. Made from a specially 10" (25.4CM) * About “Compact Grain” Belts - Aluminum Oxide #925-325-120AU 120 3" (7.6cm) x 25 /32" (64cm) 5B5D99 $ 8.99 7 developed, soft and durable rubber compound that flexes to fit #591-100-060AU 60 1E16M99 $ 20.99 Belts in super-fine grit (like 600) are only available in #925-325-220AU 220 3" (7.6cm) x 25 /32" (64cm) 5B4D99 $ 7.99 7 contours or quickly remove grinding marks. Can be rotated either #591-100-080AU 80 1E14P99 $ 18.99 what the maker calls “Compact Grain”. This process lay- #925-325-320AU 320 3" (7.6cm) x 25 /32" (64cm) 5B5H99 $ 6.99 1 5 3 direction to vary hardness of sanding surface. Fits /2", /8", /4", and 1" 7 #591-120-036AU 36 1E28F99 $ 32.99 ers grit in a special adhesive and greatly increases belt #925-325-400AU 400 3" (7.6cm) x 25 /32" (64cm) 5B4M99 $ 6.99 diameter shafts with included nested bushings. ab life. Compact grain belts are easily identified; they are 7 1 5 3 #591-120-060AU 60 1E22I99 $ 26.99 #925-325-600AU 600* 3" (7.6cm) x 25 /32" (64cm) 5B7J99 $ 10.99 SPECS: Rubber covered steel wheel. Fits /2" (1.3cm), /8" (1.6cm), /4" 1 #591-120-120AU 120 1E17E99 $ 27.99 ugly! The 600 grit belt shown looks like it should be a 60 *About "Compact Grain" Belts - Aluminum Oxide Belts in super-fine grit (like 600) (1.9cm) and 1" (2.5cm) diameter shafts. Includes bushings. Uses 1 /2" are only available in what the maker calls "Compact Grain". This process layers grit 15 grit but IT ISN’T. It really will give a 600 grit finish and (3.8cm) x 18 /16" (48.1cm) belts. Maximum Speed - 2400 rpm. #591-120-220AU 220 1E17B99 $ 21.99 in a special adhesive and greatly increases belt life. Compact grain belts are easily will last extremely well. identified; they are ugly! The 600 grit belt shown looks like it should be a 60 grit but IT #539-000-015AU 6" x 1½" Sanding Drum, 5K89M99 ��$ 93.99 #591-120-320AU 320 1E19I99 $ 24.99 ISN'T. It really will give an excellent 600 grit finish and will last extremely well. "

order on the web

Orders: 800-741-0015 brownells.com PAGE 385 METALITE CLOTH ROLLS .0025" STAINLESS STEEL Heavy, Cloth-Backed Abrasive; First Choice For Tough Metal Removal BRUSHING WHEELS “WHEELS-N-POLISH” First choice of metalworking pros for use in coarse sanding to fine polishing of the hard or ferrous metals. Ideal Super-Soft Carding Wheel For for removing old rust, scouring, deburring, finishing. Tough, rugged, aluminum oxide grain, bonded on flexible, Rust/IM Bluing At Economical Price All You Need To Get Started Right jean weight, cloth backing. Follows contours, flexes during use without flaking off. Gives a very long use-life. Tears “What do I need to start polish- straight without shredding at edge. ab Found for us by Ray Hall, Griffith, IN, these baby-soft wire wheels 1 are perfect for carding between coats when rust bluing, or when using guns?” These kits make getting SPECS: 1" (2.5cm) or 1 /2" (3.8cm) wide. ing the Hot Water Method with Dicropan IM Bluing Solution. Won’t going easy. With them, you can start GRIT 10 YD X 1" ROLL 10 YD X 1" ROLL 50 YD X 1" ROLL 50 YD X 1" ROLL 50 YD X 1" ROLL 10 YD X 1-1/2" ROLL 10 YD X 1-1/2" ROLL 50 YD X 1-1/2" ROLL remove metal, or give satin look. ab polishing and the money from those $11.99 $13.99 $47.99 $39.99 $40.99 $13.99 $11.99 $52.99 SPECS: 6" (15.2cm) diameter wheels available in 2 row and 4 row. .0025" jobs will help pay for a super, top- 3 120 #657-110-120AU NA #657-150-120AU NA NA #657-151-120AU NA NA diameter stainless steel wire. Staggered rows of 1 /4" (4.44cm) long, tufted of-the-line setup. The Kits include both stitched and loose muslin 1 wheels, plus two Polish-O-Ray™ grits and our Bluing Instruction METAL WORK METAL 220 NA #657-110-220AU NA #657-150-220AU NA NA #657-151-220AU #657-155-220AU bristles. /4" (6.35mm) hole through 2" (51mm) diameter wood center (drill 1 1 Booklet that shows you how, and when, to use those wheels and 320 NA #657-110-320AU NA #657-150-320AU NA #657-151-320AU NA #657-155-320AU to fit). 2 row has /2" (13mm) wide face. 4 row has 1 /4" (32mm) wide face. Maximum RPM 3500. grits to achieve the look wanted. WHICH KIT, 6" or 8"? If you have a 1 1 400 #657-110-400AU NA NA NA #657-150-400AU #657-151-400AU NA NA /3 or /2 hp, 1800 rpm motor, buy the 6" Kit. If your 1800 rpm motor #360-164-581AU 2 Row Brushing Wheels, 6C15B99 ��$ 16.99 3 600 #657-110-600AU NA NA #657-150-600AU NA #657-151-600AU NA NA has /4 to 1 hp, pick the 8". (A small motor can’t pull large wheels.) ab #360-164-631AU 4 Row Brushing Wheels, 6C22Q99 �� 26.99 SPECS: Kits contain: 6 Loose Muslin wheels, 6 Stitched Muslin wheels; 1 tube 240 Grit, 1 tube 400 Grit Polish-O-Ray and Instruction Booklet. 3 1 Wheels are /8" (9.5mm) thick w / /2" (12.7mm) arbor. DURITE WATERPROOF #080-724-006AU 6" Polish Kit, 8K74C99 �� $ 84.99 CARDING BRUSHES #080-724-008AU 8" Polish Kit, 8K105Q99 �� 123.99 When Wet Or Dry Paper Is A Must - STAINLESS STEEL SPONGE Durite Is The Answer GUNSMITH CARDING BRUSH - Com- Removes Lead & Rust From Steel; pact head provides better control. Sanding media developed especially Cleans Fouling From Black Three rows of soft, .003", stainless steel for wet sanding of wood finishes to get the 1" THICK Powder Shooting bristles won’t scratch through existing Dull London look, or on steel before polish- caustic blued finishes. 7-ply, laminated, ing. Great on 1911 frames and slides. Works Stainless steel sponge cleans hardwood handle. LOOSE MUSLIN WHEELS great wet or dry. Silicon carbide grain; 7 3 down to the original surface. Ideal SPECS: .003" (.07mm) diameter bristles, /16" (11mm) long, /8" (9.6mm) Economical - strong, waterproof, backing paper. ab 3 3 for cleaning rust from loading dies, bullet molds, and guns without wide, 1 /8" (3.5cm) long, 7 /4" (19cm) long overall. 1 Equals 4 /2, 20-ply Wheels SPECS: 9" (22.9cm) x 11" (27.9cm). damaging the bluing. Won’t leave steel whiskers like steel wool. Cut #353-012-003AU Gunsmith Carding Brush, 3E6C99 ��$ 9.99 STOCK # GRIT STOCK # GRIT up and wrap around jags or bore brushes to scrape plastic foul- Easy to handle, economical way to set ing out of shotgun barrels, or lead and powder gunk out of black HAND CARDING BRUSH - Cards light up 1" face wheel. Arbor stitched only. ab POLISHING #657-250-220AU 220 #657-250-400AU 400 1 powder rifles and pistols. Sponge won’t rust and can be cleaned rust from any part without scratching; SPECS: 1" (2.5cm) thick; equals 4 /2, 20-ply 1 5 3 7 #657-250-320AU 320 #657-250-600AU 600 for multiple uses. you can do Dicropan IM™ or rust bluing wheels. Arbor: /2" (12.7mm), /8" (15.9mm), /4" (19mm), /8" (22.2mm), 1" — Advise # — 50 Sheets Durite, one grit, not asst., SPECS: Stainless steel. Sold in paks of two sponges. without a power buffer. (2.5cm). Wheel Dia.: 6" (15.2cm), 8" (20.3cm), 10" (25.4cm). 1 5 7E71I99 ��$ 74.99 #080-000-321AU Stainless Steel Sponge, 8K10A99 ��$ 12.99 SPECS: 12 /2" (31.7cm.) long, /8" (15.8mm.) wide, .005" (.13mm.) stainless steel wire 6" 8" 8" 10" 10" DOUBLE ULTRA-FINE 1200 GRIT WET OR DRY PAPER - For folks bristles. Curved hardwood handle. ARBOR $17.99 $19.99 $20.99 $27.99 $16.99 wanting the “high-shine” finishes. Follow with our Five “F” Com- #084-091-006AU Hand Carding Brush, 5A10Q99 ��$ 12.99 pound for an eye-popping gleam. 2 ½" #032-061-500AU NA NA NA NA SPECS: 12" (30.5cm) x 12" (30.5cm) sheets. 1200 grit. DICO ABRASIVE WOOL ¾" #032-061-750AU #032-081-750AU NA #032-091-750AU NA #657-251-900AU 1200 Grit Durite, 5 or more sheets, Long-Lasting, Rust-Free Alternative ½" NA #032-081-500AU NA NA NA each, 7E2J99 ��$ 3.99 To Steel Wool 5⁄8" NA NA #032-081-625AU NA NA FELT BOBS MANDREL MOUNTED 7⁄8" NA NA #032-081-875AU NA #032-091-875AU Synthetic, non-metallic alternative to Get Into Those Tight Places 1" NA #032-081-001AU NA #032-091-001AU NA steel wool is long lasting and won’t rust or shed fibers. Use on wood, plastic, or metal to Ideal for polishing around trigger- ABRASIVE WOOLS produce a desired finish, or to clean away rust, carbon, dirt, or crud guards, cylinder flutes, ramps, ham- deposits. Lasts longer than steel wool—when the fibers get clogged mers, triggers, etc. Made of best hard Bronze Wool - Can be used for just about with debris, just wash the pad with cold water, air dry, and it’s ready felt. Use with Polish-O-Ray®. ab everything that steel wool is used for. Will to reuse on other projects. Safe for use with cleaning and stripping STOCK # DIAMETER FACE MANDREL PRICE not rust, nor is it as abrasive as steel wool. solvents. Coarse is for fast rust removal and smoothing rough wood; 1 3 1 FELT BOB POLISHING KIT It’s just about perfect for rubbing down a Medium is for paint surface preparation, pre-soldering and pre- #839-500-025AU /4"(6.3mm) /8"(9.5mm) /8"(3.1mm) 2C5G99 $ 8.99 nicely blued gun that has just a bit of rust or 3 1 brazing cleaning; Fine is for metal and wood surface finishing. ab #839-500-750AU /4"(19mm) 1"(2.5cm) /8"(3.1mm) 2C5D99 $ 8.99 Eases Polishing Of Odd Shapes & crud that must be removed. It will not rub 1 SPECS: Synthetic abrasive material. #839-500-900AU 1"(2.5cm) 2"(5cm) /4"(6.3mm) 2C8H99 $ 11.99 Tough-To-Reach Places through blue and the long, soft strands re- #032-000-011AU Abrasive Wool, Coarse, 2C3G99 �� $ 4.99 1 sist break down and sharding off into work. Mounted Bobs have /8" (3.1mm) #032-000-010AU Abrasive Wool, Medium, 2C3E99 �� 4.99 Great for removing stripper-softened shanks. Kit contains 3 each of the bobs stock finish, or whiskering during finishing. #032-000-009AU Abrasive Wool, Fine, 2C3L99 �� 4.99 listed below plus a compartmented SPECS: #00 (Fine) and #1 (Medium) #3 MATTE & CARDING WHEELS bench box. ab (Coarse). Packed 3 pads in bag per grade. Knock Off the Rust & Do Heavy Carding, Too SPECS: The 3 each of our 8 most popular sizes and shapes - for a total #439-200-101AU #00 Bronze Wool Pads, 8K10I99 ��$ 12.99 of 24 felt bobs. #439-200-201AU #1 Bronze Wool Pads, 8K12G99 �� 14.99 BLENDING WHEELS RIEHL WHEELS - .005" wire, max. #080-560-000AU Felt Bob Polishing Kit, 8K56N99 �� $ 62.99 #439-200-300AU #3 Bronze Wool Pads, 8K14L99 �� 15.99 RPM 4,000. Preferred for rust or hot Polishing, Cleaning, Blending water bluing to give soft, wiping action FELT BOB REFILL PAKS - Paks of three. MILD STEEL STEEL WOOL - Get the ex- A wire wheel without the “Gotcha”! Woven at 500 to 600 rpm. Available with ½" MANDREL MOUNTED BOBS (12.7mm) or ¾" (19mm) arbor. 1 act abrasive action you need for all kinds synthetic material impregnated with silicon 2 1 #080-560-101AU Square, 1"x / ", 8K14A99 �� $ 16.99 2 of jobs. Highest quality “wool”; full range carbide abrasive. Follows curves well. 3000 SPECS: 6" (15.2cm) diameter, / " (12.7mm) face. 1 3 #080-560-102AU Square, /2"x /8", 8K8H99 �� 9.99 of cuts. rpm, maximum. ab MONITOR WHEELS - .006" wire, max. RPM 6,000. For harsher 1 SPECS: 5 grades: #0000 Super Fine; #000 SPECS: 6" (15.2cm) dia. 1" (2.5cm) thick. 2" (5.1cm) carding action, or for giving light matte finish. Not stiff enough to #080-560-103AU Tapered Cone, 1"x /2", 8K11A99 �� 14.99 Extra Fine; #00 Very Fine; #0 Fine; and #1 Medium. 8 pads per pack. arbor hole. Arbor adapters sold in pairs. remove rust, scale, or grime from abused guns. UNMOUNTED BOBS only 1 #439-300-400AU #0000 Steel Wool, 8K5P99 ��$ 6.99 #657-586-970AU Very Fine Blending Wheel, 7E56Q99 �� $ 60.99 SPECS: 6" (15.2cm) diameter, /2" (12.7mm) face. Available with ½" #080-560-201AU Knife, 1", 8K6A99 �� 7.99 (12.7mm) arbor only. 5 #439-300-300AU #000 Steel Wool, 8K5M99 �� 6.99 #657-586-020AU Fine Blending Wheel, 7E53G99 �� 58.99 #080-560-202AU Knife, /8", 8K3P99 �� 4.99 1 #671-210-500AU 6" Monitor Wheel, /2" Arbor, 1G62J99 �� $ 65.99 1 #439-300-200AU #00 Steel Wool, 8K5N99 �� 6.99 #657-586-060AU Medium Blending Wheel, 7E50M99 �� 59.99 #080-560-211AU Square, 1"x /4", 8K4Q99 �� 5.99 3 1 NOTE: - DO NOT use the same wire wheel for two different metals. The little bits of 8 #439-300-100AU #0 Steel Wool, 8K5M99 �� 6.99 #671-751-500AU /2" Blending Wheel Arbor Adapter, #080-560-212AU Square, 1"x / ", 8K10H99 �� 12.99 one metal left in the wheel can transfer to the next metal causing spots and discolor- 1 #439-300-101AU #1 Steel Wool, 8K5Q99 �� 6.99 pair, 1G4G99 �� 5.99 ation in bluing and plating baths, or leaving rustable mild steel bits in brushed stainless. #080-560-213AU Square, 1"x /8", 8K2A99 �� 4.99

GUARANTEED. FOREVER.

PAGE 386 SINCE 1939 Office/Tech: 641-623-5401 METAL WORK POLISHING - - - - ab 3.99 3.99 3.99 3.99 3.99 3.99 6.99 $ 3.99 $ 15.99 $ 13.04 �� 387 ��

��

�� 2C2I99 2C2J99

ab 2C2J99 PAGE 2C2M99 �� 2C2I99 2C2Q99 is a fine abra White Ice is �� lb. (.68 kg) wt. kg) lb. (.68 is a medium cut medium a Gray Star is 2 / 1 Polishing abrasives have a have abrasives Polishing Coarse Grit To Mirror Finish To Coarse Grit 2C5M99 WHEEL PREP™ WHEEL 8K13I99 Covers All Polishing Needs From From Needs Polishing All Covers general purpose compound is oli general purpose compound myriad of uses in the shop. Cream the uses in myriad of is coarse and abrasive Bobbing starting on metals for aggressive surface. Brown Trip with a rough a medium abrasive and safe for all for a medium abrasive and safe metals. ting compound for harder metals harder ting compound for steel. like metals softer sive compound for

- �� FLITZ

Cream Bobbing Compound, Compound, Brown Tripoli Gray Star Compound, White Ice Compound, Green Flexible Compound, Plastic Blue Compound, Green Rouge, Blizzard Premium Compound, 2C2A99 Flitz Rifle, Gun & Knife Wax, 4A11M80 Wheel Prep, Will Thank You For You Thank Will ab POLISHING COMPOUNDS DIVINE BROTHERS COMPOUNDS DIVINE BROTHERS 7.6 fl oz. (225ml) flip-top bottle. (225ml) flip-top fl oz. 7.6 Cardboard tube, approximately 1 tube, approximately Cardboard Packed in cardboard; approximately 5" (12.7cm) long x 1" (2.5cm) long x 1" (2.5cm) 5" (12.7cm) approximately in cardboard; Packed Water-Repelling Protectant Your Guns Your Protectant Water-Repelling RIFLE, GUN & KNIFE WAX RIFLE, Non-abrasive, silicone-free protectant shields shields protectant silicone-free Non-abrasive, Saves time and saves pol and saves time Saves Conserves Your Polish Conserves Your Conditions Your Wheels, Your Conditions that require a delicate touch or as the final step in polishing steel. a delicate require that safe is and cut medium-to-fine a has Green Flexible Multi-Purpose gives a mirror- Blue polish. Plastic all metals; a good, all-around for on plastic great Works smooth finish to acrylic, plastic, or fiberglass. nickel, is a good choice for tips. Green Rouge grip caps or forend or white gold. Blizzard Premium is a white compound that silver, metals. harder finish on an almost mirror leaves SPECS: SPECS: ish by putting it on the wheel the it on by putting ish wheel is trued but before the Apply after walls or floor. and not on the and prepares polish. Instantly conditions greaseless you apply your load single a in polish of amount maximum the accept to wheel the . Not polishes ONLY For greaseless wheels. types of on all ing. Works based polishes. 555 or other grease/tallow with Brownells use for SPECS: SPECS: SPECS: wide x 1" tall. firearms and knives from rust and the corrosive effects effects rust and the corrosive and knives from firearms sap, spots, tree fingerprints, water powder residue, of contains a Wax Knife Rifle, Gun & blood, and more. Brazilian Carnauba wax and beeswax unique blend of lasts up to six months in finish that a tough, protective to provide environments. months in salt water conditions and three water fresh all metals – blued steel, stainless steel, brass, aluminum, for Safe paint, stocks, - as well as wood and fiberglass plating and nickel no white residue dust, and leaves attract acrylics, and plastic. Won’t or buildup. #032-000-013AU #032-000-014AU #032-000-015AU #032-000-016AU #032-000-017AU #032-000-023AU #032-000-024AU #032-000-012AU #314-000-006AU #080-505-000AU - - ®

$ 7.99 16.99 16.99 16.99 16.99 $ 7.99 $ 16.99 " (9.5mm) " (9.5mm) 8 / 3 ARBOR (19mm) (22.2mm) 4 8 / / . It consists; 3 7 ® �� 8K13H99 STOCK # STOCK 8K13I99 8K13B99 8K13A99 8K13H99 POLISH-O-RAY

#032-837-750AU #032-837-875AU 2C6B99 ab For The Professional The For " arbor only, or 8" (20.3cm) dia., both both dia., or 8" (20.3cm) " arbor only, Shop-Proven Premium-Grade Polish Premium-Grade Shop-Proven 2 / SISAL WHEELS SISAL 1 The answer to a gun polisher’s dream! Made dream! The answer to a gun polisher’s drying abrasives, Polish- ORay hard 1) Unlike 2) It is easily applied to polishing wheels without ARBOR (15.9mm) (12.7mm) lb. (1.1 kg) net contents (min.) plastic tube. net contents lb. (1.1 kg) 8 2 2 / / Polish-O-Ray, 240 320 Polish-O-Ray, 400 Polish-O-Ray, 500 Polish-O-Ray, Polish-O-Ray, 140 6" Sisal Wheel, 1 5 / 1 to the highest standards of quality with carefully with carefully quality of to the highest standards repeatable reliable, grits for true-sized screened, doesn’t base that greaseless and a natural, results jobs. mess up bluing or plating to a residue leave flexible plastic tube to stay in a formed, Packed between uses. fresh hard surface without flinty sets up to a medium soft can used, being size grit of regardless which, flakes do serious damage to a polished surface. the open end of Simply press stopping the motor. to the the tube to your wheel; the polish adheres 8" Sisal Wheel, 2C6K99 Packed in 2 Packed 6" (15.2cm) for for 6" (15.2cm) Metal & Rust & Metal ab STOCK # STOCK Woven jute with outer jute with outer Woven Polish-O-Ray is shipped in a resealable outer bag. Put the tube is shipped in a resealable Polish-O-Ray By following the “Master Metal Polisher’s” technique, it is pos the “Master By following 3) Because of its softer nature, a true, ripple-free surface is a true, ripple-free nature, its softer 3) Because of finishers, has been used by gunsmiths, metal 4) Polish-O-Ray Fast Removal Of Rough Of Rough Removal Fast SPECS: SPECS: muslin cover. Aggressive Aggressive muslin cover. rough surface removes Use with metal and rust. a “brushed” finish. fine grits for wide. 7-ply, spiral stitched. wide. 7-ply, #080-505-240AU #080-505-320AU #080-505-400AU #080-505-500AU #080-505-140AU #032-837-500AU #032-837-625AU — Advise # — #032-637-500AU mainly, of starting with the coarsest grit and polishing the surface starting with of mainly, wheel finer grit on a different the next then, with in one direction; this procedure 45° angles to the first “pass”. By following polishing at unequaled is surface final the numbers, grit finer the through down quality and perfection. for all your Polish- store back in the bag, seal with a twist tie and ALWAYS longest for - brand new or partially used - in the refrigerator O-Ray life. SPECS: SPECS: facturer in the southeast orders by the keg. And, where else but on but else where And, keg. the by orders southeast the in facturer These praise and admiration? finish draw more a gun does a perfect continuing Polish-O-Ray’s for the reason beautiful finishes are hobbyists. popularity among our country’s gunsmiths and serious time with sible to obtain a top quality finishing job in a minimum of Bluing Instruction Booklet in our Complete instructions are P-O-R. and the book Gunsmith Kinks free) (#076-200-113, moving surface, hardens in a few seconds and is ready for use. for seconds and is ready in a few moving surface, hardens polished surface, possible all wheels. The best on obtained quickly a superior, is your assurance of ripples and bounce marks, from free you. does this for job. Polish-O-Ray refinishing professional a quality since the early 1940’s. Wherever manufacturers and aircraft is and imperfections marks scratch marks, chatter from surface, free manu One precision is a MUST. Polish-O-Ray the use of required,

- order on the web

16.99 16.99 $ 16.99 $ 16.99 NA NA NA NA $13.99 brownells.com NA NA Loose $7.99 ab ab 10" STITCHED 10" LOOSE #032-938-001AU ��

�� #032-920-750AU #032-920-875AU #032-920-001AU ��

" (22.2mm), 1" (22.5cm). " (22.2mm), 1" (22.5cm). 8

/ NA NA NA 7

$11.99 8K14G99 �� 8K14A99 10" STITCHED #032-938-875AU #032-938-750AU 8K14K99 Sisal Wheel Polishing Wheel Sisal $5.99

Stitched 8" LOOSE " 919mm), Get fast cut and color on steel 4 / 3 8K13N54 " (.5mm) face. Loose wheels are 20 ply. 20 ply. wheels are Loose face. " (.5mm) The Right Grit & Base For Effective Effective For Grit & Base Right The #032-820-500AU #032-820-625AU #032-820-750AU #032-820-875AU #032-820-001AU 8 when used with Sisal Wheels. Alumina abrasive and tallow base loads easily / 3 $12.99

8" STITCHED LOOSE MUSLIN WHEELS LOOSE #032-838-875AU #032-838-750AU #032-838-625AU #032-838-001AU #032-838-500AU " (15.9mm), " (15.9mm), 8

/ MUSLIN WHEELS MUSLIN 5 555 White, Fine Sisal Polish, Medium Sisal Polish, Coarse Sisal Polish, NA NA NA NA STITCHED MUSLIN WHEELS $5.99 6" LOOSE SISAL WHEEL POLISH NA NA NA $5.99 #032-620-500AU " (12.7mm), " (12.7mm), 6" STITCHED 2 Stitched wheels have Packed in 3 lb. (1.4 kg) cardboard tube. cardboard kg) in 3 lb. (1.4 Packed / #032-638-625AU #032-638-500AU 1 Polishing Jobs Polishing Mainstay Of Any Any Of Mainstay Spiral Stitched - used Spiral Stitched grit to smooth out each change of Loose Muslin - used following your as wide as wheel each make to enough sections Use - Note: ARBOR ½" 5/8" ¾" 7/8" 1" ¾" 7/8" 1" ½" 5/8" Polishing Room For Most For Room Polishing ARBOR Wheel Diameter: 6" (15.2cm), 8" (20.3cm), 10" (25.4mm). 8" (20.3cm), Wheel Diameter: 6" (15.2cm), Arbor: SPECS: SPECS: primarily for first cleaning primarily for on the gun with operation bring and rust and dirt blue, old off knock to O-Ray™ Polish- 140 No. instead of operators bright finish. Also used by some the metal to a must care great flexible nature, a more Felt wheels - being of Soft and screw or funnel and elongate edges, to not round be exercised pin holes. next finer grit. Also used the the surface for and prepare grit marks gun just prior to bluing. the to finish off sections to each three - a minimum of polishing motor will handle grit numbers. different same wheel for wheel. Never try to use the it with the grit number and in use, mark After a wheel is broken-in to be turned. Will increase rotation of to be used on it and direction work. hours of give better finishes and save wheel life, #080-555-002AT SPECS: SPECS: ors quickly, approximates a #240 Polish-ORay ™ finish. Medium; a #240 approximates ors quickly, Coarse; removes buffing and coloring out in one operation. for polishing. excessive without and tool marks scratches ever you’ve finish gorgeous most absolutely the For - WHITE 555 surfaces, with this. Often used to buff plated 555 Gray seen, follow finish. Does a a mirror leaving out 555 Gray marks this grade takes nice job on aluminum too. and lasts longer without streaking or burning. Fine; Cuts and col and lasts longer without streaking #080-599-105AU #080-599-110AU #080-599-100AU - - - hp 2

/ 1

$ 16.99 $ 16.99 8" NA NA NA NA NA NA NA 10" $105.99 $105.99

#088-281-875AU #088-091-001AU 8" NA $85.99 ab

#088-181-750AU #088-181-625AU

8" NA NA NA NA 8" NA NA $68.99 $104.99 �� Aluminum And More And Aluminum �� Three Finer-Than-Fine Finer-Than-Fine Three - Mirror Finishes On Steel, On Finishes Mirror #088-081-875AU #088-281-625AU #088-281-750AU Cake Polishes For Gorgeous For Polishes Cake 8K13I99

8K14C99

ab 8" NA NA 6" NA NA NA $67.99 $52.99

#088-081-750AU #088-081-625AU #088-081-500AU 6" hp or over can use 10" at 1800. 10" for expe 10" for 1800. use 10" at hp or over can NA hp or under, use 6" wheels at 3600 RPM, 3600 RPM, at use 6" wheels hp or under, #088-261-625AU SOFT FELT POLISHING WHEELS POLISHING SOFT FELT 4 2 HARD FELT POLISHING WHEELS FELT HARD / 800-741-0015 / $57.99 MEDIUM FELT POLISHING WHEELS MEDIUM FELT 3 1 555 Black, 555 Gray,

No. 555™ POLISH #088-161-625AU #088-161-500AU

6" 6" NA NA NA NA NA NA - The coarsest of the three, so you can move to the the three, - The coarsest of FELT POLISHING WHEELS POLISHING FELT $51.95 $42.99 - Although extremely “fine”, it’s “coarser” than 555 White. 555 than “coarser” it’s “fine”, extremely Although -

All are 1" ( 2.5cm) thick. All made with 1" (2.5cm) arbor. Adapters arbor. thick. All made with 1" (2.5cm) ( 2.5cm) 1" All are All packed 3 lb. (1.4 kg) net weight in cardboard tube. in cardboard net weight kg) 3 lb. (1.4 All packed #088-061-750AU #088-061-500AU #088-261-500AU “Good Old Five-Fifty-Five” as the boys call it. This is the “secret” as the boys call it. This is the “secret” Old Five-Fifty-Five” “Good Finest quality 1" wide felt wheels, felt quality 1" wide Finest

Professional, Gunsmith-Proven Professional, ½" 5/8" ¾" 7/8" ½" 5/8" ¾" ½" ¾" 5/8" 7/8" 1" ARBOR ARBOR ARBOR #080-555-001AU

#080-555-004AU Orders: Gray removes 500 P-O-R™ marks while leaving slight marks which slight marks while leaving marks 500 P-O-R™ Gray removes clean up with 555 White. 555 GRAY 555 BLACK aluminum after polish for as a “Coloring” Great 555 family sooner. skip to “White” on steel, with “Gray” Follow sanding steps. final the on aluminum. SPECS: SPECS: mend hard felt, followed by loose muslin for each grit as you prog you as grit each for muslin loose by followed felt, hard mend the when grits three the of any with stop can You them. through ress the find to experiment you Suggest achieved. is finish of level desired best in your shop. combo and sequence you like rienced polishers only. Use the soft felt for most work, medium, or most work, for felt the soft Use only. rienced polishers 555™ Polish. wheel for hard SPECS: convert to 1⁄2" (12.7mm), 5⁄8" (15.9mm), 3⁄4" (6.4mm) and 7⁄8" (22.2mm). 7⁄8" and (6.4mm) 3⁄4" (15.9mm), 5⁄8" (12.7mm), 1⁄2" to convert 10"x1"). wheel (except One Adapter supplied with each plete instructions on Polish-O-Ray™ on Polish-O-Ray™ plete instructions wheel It is best to use a different wheel technique. felt tube describes polish grit. each for that master polishers use to give that mirror finish to the gun after finish to the gun after mirror master polishers use to give that that recom we finishes, possible brightest the For 500. Polish-O-Ray™ carefully selected and factory trued. factory trued. selected and carefully truing may be required.) (Final touch-up density of controlled Only the closely will give the superb finish wheels felt Com professional. the real marks that or over, 8" at 1800, 1800, 8" at or over, FORMAX SILICON CARBIDE ALUMINUM OXIDE DAVE’S METAL WORKS SATIN-GLO POLISHING COMPOUND ABRASIVE COMPOUND ABRASIVE BLASTING GRIT SHAKE & BLAST CANISTER Greaseless Compound For Ideal For Sandblasting Small Parts Produces Matte “French Gray” Finishes Effortless Polishing Sharp-Edged Silicon Carbide Convenient, hand-held Shake & Blast Self-Lubricating Petroleum Base By using controlled, abrasive blasting with Loads quickly and produces a Canister is ideal for sandblasting hard to these extremely fine, aluminum-oxide grits, smooth, great-looking finish without a lot of hard work. Uniform, The very best abrasive compound for hang on to parts such as screws, sight you can “color”, “texture” or “tone” any metal aluminum oxide abrasive in a water-soluble, glue base removes “hard fitting” two pieces of steel. Stands blades, and other small parts that always surface to produce the desired cosmetic ef- machine marks, pits and surface imperfections in all types of steel, up to continued fitting even on hardened seem to get lost in the big sand blasting cabinet. Rigid steel screen fect without washing out detail. Professional leaves the parts clean, dry and ready to complete your favorite fin- and heat-treated steel. Silicon carbide grit contains holes small enough to hold parts as small as .0625" (.16cm) combined with a thick, long lasting lubri- instructions included. ab in diameter but allows blasting material to filter through without

1911 AUTO ish. Conveniently packed in three pound, resealable tubes. For best SPECS: 6 lbs. in screw-top, plastic jar. 15 lbs. in 1 clogging. Screen is held firmly in place with two specially cut, /2" METAL WORK METAL results, store unused portions of tubes in the refrigerator. ab cant breaks down into smaller and smaller snap-top pail. SPECS: Packed in approximately 3 lb. (1.4 kg) tubes. sharp-edged particles to keep cutting longer than aluminum oxide thick PVC caps. A third cap turns to lock in place and comes with 1 #330-100-100AU 100 Grit Satin-Glo Compnd, compounds. For use on steel only. Remove with solvent. ab STOCK # QUANTITY GRIT PRICE a rubber “apron” to hold /2′to 1" blast nozzles and prevents “back 3C10C99 ��$ 12.99 SPECS: 4 fl. oz. (118 ml). blast” while you work. ab #084-206-060AU 6 lbs. (2.7kg) Ex-Coarse 5L20C99 $ 24.99 3 SPECS: Steel screen, PVC caps, /8" (13.6cm) long, 3" (7.6cm) wide. Inside #330-100-150AU 150 Grit Satin-Glo Compnd, 3C11B99 �� 13.99 5L47A99 1 STOCK # GRIT SIZE PRICE #084-212-060AU 15 lbs. (6.8kg) Ex-Coarse $ 56.99 dimensions: 4 /2" (10.8cm) long x 3" (7.6cm) diameter. #330-100-220AU 220 Grit Satin-Glo Compnd, #084-206-120AU 6 lbs. (2.7kg) Coarse 5L20L99 $ 24.99 #260-000-002AU Shake & Blast Canister, 6B50B99 �� $ 54.99 3C13H99 �� 15.99 #083-045-120AU 120 5L13G99 $ 16.99 #084-212-120AU 15 lbs. (6.8kg) Coarse 5L47G99 $ 56.99 #330-100-320AU 320 Grit Satin-Glo Compnd, 3C11I99 �� 13.99 #083-045-180AU 180 5L13P99 $ 16.99 #084-206-240AU 6 lbs. (2.7kg) Fine 5L21J99 $ 25.99 #330-100-400AU 400 Grit Satin-Glo Compnd, 3C12E99 �� 13.99 #083-045-240AU 240 5L13G99 $ 16.99 #083-045-320AU 320 5L14K99 $ 17.99 #084-212-240AU 15 lbs. (6.8kg) Fine 5L49L99 $ 59.99 #083-045-400AU 400 5L14B99 $ 17.99 SANDBLAST CABINET GLOVES #083-045-600AU 600 5L22G99 $ 29.99 Heavy Duty, Seamless Rubber FLITZ POLISH #083-045-800AU 800 5L22K99 $ 29.99 GLASS BEADS Replacements For Worn Out High Luster On Blued Steel, Aluminum, Brass, SILICON CARBIDE ABRASIVE KIT - Puts the most Blast Cabinet Gloves Plastic, Glass & More useable selection of our shop proven, oil-based, Lets You Do Popular Matte Finish Durable synthetic rubber gloves Absolutely non-abrasive polish for all metals, silicon carbide abrasive compound together in Right In Your Own Shop are the perfect replacements for worn fiberglass and most hard plastics. Removes corro- a convenient try- pak. Handy, 2 oz. jars give you or damaged gloves on sandblasting sion, tarnish and discolorations. Brings finishes up to just the right amount of long lasting, sharp-edged Glass beads are used to make the matte cabinets with 8" diameter glove openings, including the popular superb brightness, but its greatest asset in the gun- abrasive that cuts longer and won’t break down. finish that is so highly sought after. Fast to do; Empire cabinets. Extended gauntlet style with plenty of length and POLISHING shop is the ability to remove surface rust from blued The best choice for close fitting of hardened and easy to get results wanted. Must be done in molded-in finger curves to aid in grasping and maneuvering the finishes without damaging the bluing underneath. tempered steels. 4 oz. replacement containers listed above. enclosed blast cabinet. Used by many custom blast nozzle as you work. Heavy-duty, seamless construction stands Leaves a protective film that resists further rust, cor- SPECS: 2 fl. oz. (59 ml). Kit contains 120, 180, 240, 320, 400, 600 and rifle and pistol builders. Finish can be blued, up to hard use and eliminates stress points at seams where gloves rosion, etc., for up to six months. Contains no acids. ab 800 grit. plated, or left in-the-white. ab can prematurely tear. Slightly oversized for ease in getting hands in 3 SPECS: Two sizes. U.S. Sieve Size #60-100 (.0098-.0059") for deep matte SPECS: 50 g (1 /4 oz) or 150 g (5.3 oz) tube. #080-905-000AU Silicon Carbide Abrasive Kit, and out quickly. ab

10/22 PERFORMANCE PARTS coverage; field or utility guns. #270+ (.0021-.0005") for softer, matte look #314-100-050AU 50 gram Flitz Polish, 4A7M99 �� $ 9.99 8K52F99 ��$ 61.99 SPECS: Synthetic rubber, black. 31" (79 cm) long. Fits sand blasting cabi- matching stainless steel finishes. 50 lb. (22.7 kg) of beads in sealed pail, nets with 8" dia. openings for gloves. Sold in pairs. #314-100-150AU 150 gram Flitz Polish, 4A19C99 �� 20.99 SILICON CARBIDE ABRASIVE GRIT - Very fine shipped by UPS. #100-003-400AU Sandblast Cabinet Gloves, 5B72H99 �� $ 76.99 abrasive powders you can use to “rub in” parts. FLITZ LIQUID POLISH - Non-abrasive liquid applies easier, leaves #084-063-100AU #60-100 Glass Beads, 4H67P99 �� $ 84.99 Make an abrasive/cutting-oil paste for metal work a protective film coating. #084-063-270AU #270+ Glass Beads, 4H67A99 �� 84.99 or use dry on a soft pad to bring a cured stock finish SPECS: 100 ml (3.5 oz.) bottle. to a gloss. Follow with Brownells Stock Rubbing #314-101-100AU 100 mL Flitz Liquid, 4A10K99 �� $ 11.99 Compound. SPECS: 120 grit (coarse); 600 grit (fine). 1 lb. net wt. in DONEGAN OPTICAL GUN & KNIFE POLISHING KIT - Easy-to-use envi- plastic jar. ronment-friendly products help you clean, polish, VISOR LIGHT™ and protect the exterior surfaces of guns, knives, #080-537-120AU 120 Grit Silicon Carbide, 5L8K99 ��$ 14.99 gunsmithing tools, and other metal items. Comes #080-537-600AU 600 Grit Silicon Carbide, 5L20L99 �� 24.99 BEDDING/MASKING TAPE Improves Visibility For Detail Work with original Flitz paste, plus oil-free, water-based Extra-Heavy Duty For Abrasive Blasting Hands-free light clips to OptiVISOR and Gun & Knife Cleaner for thorough degreasing and directs bright light right where you look. Ver- Rifle, Gun & Knife Wax, a solvent-free, non-abrasive High-density, PVC tape easily protects carefully tical swivel adjustment lets you aim the light polish that shines, protects, and resists fingerprints. precisely. Self contained battery pack clips to headband. SPECS: Polishing Cloth - 12" x 12" (30.5cm x 30.5cm). Contains Flitz Paste polished sides of 1911 Auto slides, pistol frames, or 3 shotgun and rifle receivers from abrasive grit in the SPECS: Uses 2 AA batteries, not included. 1 spare bulb included. Polish - 1 /4 oz. (50g) tube; Gun & Knife Cleaner - 1.7 fl. oz. spray bottle; LAPPING COMPOUNDS Rifle, Gun & Knife Wax - 1.7 fl. oz. bottle. blast cabinet. Withstands high blast pressures up to #255-000-001AU Visor Light, 5E23G99 �� $ 25.99 100 psi. ab

ABRASIVE BLASTING #255-000-002AU Spare Bulb, 5E5Q99 �� 7.99 #314-000-003AU Gun & Knife Care Kit, 4A16A99 �� $ 17.99 Aluminum Oxide In A Water Soluble Base SPECS: Black, available in 1" (2.5cm) wide x 36 yds (33m) For Easy Cleanup long or 2" (5cm) wide x 36 yds long rolls. 10/22 PERFORMANCE PARTS The right abrasive for lapping the final fit #084-092-101AU 1" Bedding/Mask Tape, 4H7M99 �� $ 10.99 between semi-auto slides and frames, rifle #084-092-001AU 2" Bedding/Masking Tape, SIMICHROME POLISH bolts and receiver raceways, and any other ap- 4H13Q99 �� 16.99 INSPECTION ACCESSORIES plication where a super-close fit or silksmooth For Brass, Chrome, Gold, mechanism is required. #600 and #800 grit MAGNIFIER - Compact, folding pocket Silver, Aluminum, Glass aluminum oxide abrasive crystals in a long lasting petroleum base magnifier. Double lens system gives com- & Plastic bined 8X. Get a closer look at anything. that’s water soluble for fast, easy cleanup in soap and water. Alumi- 1 SPECS: 1 /4" (3.2cm) diameter glass. Not only for clean- num oxide crystals are smooth and rounded in shape, so they won’t GARNET LAPPING COMPOUNDS - Fast-working, but absolutely embed and continue to wear the part after cleanup. ab non-embedding, petroleum abrasive paste for honing close-fit- #345-534-002AU Double Lens Magnifier, ing up brass but is the most fantastic stuff you have ever seen on 5D12A99 ��$ 16.99 chrome, gold, silver, aluminum, glass and plastic. The people who SPECS: Aluminum oxide. 4 fl. oz. (118 ml). Available in #600 and #800 ting parts to an ultra-smooth, friction-free fit. A natural substance, grit. Twin Pak contains one jar of each grit. import it from Germany put it this way: “Absolutely guaranteed to Garnet can be safely used on cast iron, brass, bronze or softer steels LOUPES - Instantly turns prescription or be the best polish in the world or your money back”!! One of the big #083-041-600AU #600 Lapping Compound, without embedding or galling. safety glasses into magnifiers for close problems in the gun shop is polishing Plexiglas, and other plastic 3H23A99 �� $ 29.99 SPECS: Garnet, oil-base paste. 4 oz. (113 g). GK-5 = 600 grit. GK-7 = 800 up work. Pivots out of the way when not spacers and inserts. Simichrome will do it “Quick as a Wink”. #083-041-800AU #800 Lapping Compound, grit, GK-10 = 5 microns. needed. Attaches to either right or left side. SPECS: 1.76 oz. (50 g) tube, a 8.82 oz. (250 g) can. 3H23I99 �� 29.99 #083-047-005AU GK-5 Lapping Compound, 3H16Q99 �� $ 19.99 Precision-ground optical glass. 1 #189-001-000AU 1.76 oz. Tube Simichrome, 9H12B99 �� $ 14.99 #083-041-002AU Twin Pak Lapping Compound, #083-047-007AU GK-7 Lapping Compound, 3H16G99 �� 19.99 SPECS: 24mm dia. 3X magnification, 3 /2" (9cm) focal length.ba #189-002-882AU 8.82 oz. Can Simichrome, 9H39C99 �� 46.99 3H41H99 �� 49.99 #083-047-010AU GK-10 Lapping Compound, 3H16K99 �� 19.99 #255-300-003AU 3X Loupe, 5E15K99 �� $ 22.99

GUARANTEED. FOREVER.

10/22 PERFORMANCE PARTS PAGE 388 SINCE 1939 Office/Tech: 641-623-5401 METAL WORK ENGRAVING & STAMPING - - 6.99 8.99 8.99 $ 9.99 $ 9.99 $ 9.99 $ 9.99 $ 9.99 $ 9.99 $ 8.99 $ 8.99 35.99 25.99 23.99 $ 6.99 $ 31.99 $ 22.99 $ 29.99 $ 231.99 " (1.6mm). " (1.6mm). PRICE 16 389 / 1 �� #9/.123 #10/.097 #/WIDTH

8K5I99 8K6I99 �� 5A5E99 8K6J99 5A5B99 �� 8K6K99 8K5N99 8K5M99 �� PAGE �� ® b 5A13M99 ONGLETTE 5A12N99 " (3.2mm) to " (3.2mm) 8 9D28J99 9D22B99 9D32P99 Of Each Stroke Each Of / 1 7A7D99 7A5L99 " (3.2cm). 7A7K99 STOCK # STOCK 4 7A5D99 Designed & Balanced To To Balanced Designed & / 1 Give You Day-Long Control Day-Long You Give " (13.5cm) overall length. Approx. Approx. overall length. " (13.5cm) #348-166-909AU #348-166-910AU 8D191K99 16 / 5 #/WIDTH #36/.0130 #38/.0190 #39/.0215 #50/.0115 #0/.0170 #2/.0155 #4/.0175 " (2.9cm), 1 " (2.9cm), 8 ab " (7.9mm) diameter shank. H.S. Steel. Set in shank. H.S. diameter " (7.9mm) / 1 GRAVERS b 16 / KNIFE GRAVER FLAT GRAVERS FLAT 5 ROUND GRAVER ROUND " Chasers Hammer, " Chasers Hammer, " Chasers Hammer, 8 4 16 / / " (11.4cm) to 5 " (11.4cm) #1/.127 / 1 1 2

#/WIDTH LACQUER-STIK / Graver, #18 Bent, 6 Line Set, Die Sinker Red Lacquer Stik, Red White Lacquer Stik, Gold Lacquer Stik, Black Lacquer Stik, Graver, #8 Bent, 6 Line 15 1 1 1 #2/.0090 CHASERS HAMMER ONGLETTE POINT GRAVERS " (3.8cm) shank, tapers from from shank, tapers " (3.8cm) 2 Die Sinker Chisel, each, 8D17E99 Chisel, Die Sinker / 1 b " (23.8mm), 1 " (23.8mm), FLAT 16 / " (10.9cm) length. overall " (10.9cm) 15 " (11.7cm) long. Red, White, Gold, or Black. long. Red, White, Gold, " (11.7cm) 16 8 / / 5 5 4 H.S. Steel. 4 H.S. 6" (15.2cm) long. 6" (15.2cm) 4 Steel head, hardwood handle. Approx. 10" (25.4cm) overall length. 10" (25.4cm) handle. Approx. Steel head, hardwood STOCK # STOCK STOCK # STOCK Highly specialized compound wipes on to bring out stamped or Highly specialized The hammer most frequently seen on the benches of engravers, engravers, on the benches of seen The hammer most frequently " (3.8cm) tapered shank.a tapered " (3.8cm) Hi-Lights Engraving, Hi-Lights 2 / 1 Stamped #’s And Names And Stamped #’s #615-030-036AU #615-030-038AU #615-030-039AU #615-050-050AU #615-010-000AU #615-010-002AU #615-010-004AU #615-020-002AU SPECS: SPECS: #615-086-086AU engraved impressions on ALL smooth surfaces. Ideal for guns, parts, for Ideal surfaces. smooth on ALL impressions engraved soon hardens when used, but form in stick accessories. Semi-solid and becomes permanent. #348-166-000AU #517-100-002AU #517-100-003AU #517-100-004AU #517-100-001AU #348-166-901AU #615-086-186AU — Advise # — Hardened steel.a Hardened Approximately 1 Approximately INKER’S CHISELS INKER’S S DIE SPECS: a and 4 onglettes. 4 round, 4 flat, cludes 12 chisels, SPECS: - Precision- STRAIGHT GRAVERS exact stoning to and final touch-up for ready and finished, ground shape. cision tapping. The large, flat face enables user to watch his work and work and his face enables user to watch flat large, tapping. The cision the tool he is using. Oval shaped handle is slenderly strike still properly and action. Both flat rebounding proper near the head for tapered finished. smooth and polished highly are hammer this of faces round SPECS: sizes: Face INE GRAVERS LINE BENT SPECS: 1 silversmiths and other artisans who use a hammer for light, ultra-pre silversmiths and other artisans who use a hammer for #249-746-280AU #249-746-320AU #249-746-220AU - " - - 8 / 3 9.99 9.99 11.99 " (9cm) 2 $ 22.99 $ 55.99 / 1 $ 665.99 $ 829.99 " (14.6cm), " (14.6cm), $ 1930.99 4 / 3 �� " character sizes. Fits " character sizes. 8 - / 1 ab " (4.4cm) high, 3 " (4.4cm) ab . 4 - - �� / 3 �� 1B51A99 1E632L99 ", or �� 32 1E676K99 / �� 3 1E1834G99 ", 9A8J99 16 / 9A8L99 1 " (3.8cm) high. " (3.8cm) 2 ab . / 1 9A20P99 FORSTER/BONANZA 9A7B99 BRUSHING INLAY BRUSHING ab STEEL STAMP GUIDE STEEL STAMP lbs. (12.9kg) Spherical diameter 5 Spherical diameter lbs. (12.9kg) Gold Powder In An Easy-To-Use Kit In An Easy-To-Use Powder Gold 2 / Do-it-yourself kit fills engraving and letter Do-it-yourself kit fills engraving

1 " (11cm) long. Requires 1.0 1.0 " (11cm) long. Requires 2 / 1 ing on all guns with an attractive gold colored gold colored ing on all guns with an attractive Gold Kit, Gold Powder, Liquid Base, Cleaner, GRS ENGRAVING GRS System 3 Engraver, Steel Stamp Guide, Engraving Block, Gravermeister, " diameter. 8 " (8.2cm) wide, 1 " (8.2cm) / 4 3 / 1 " square stamps with " square 4 ab 3" (7.6cm) wide, 1 3" (7.6cm) - Jaws " (18.4cm). / . 1 4 / Aluminum, natural finish with steel U-bolt and hardware. 2 finish with Aluminum, steel and natural hardware. U-bolt 1 Handpiece; 4 Handpiece; Steel. Weighs 28 Steel. Weighs 115V, 60Hz. 16" (40.6cm) long, 9" (22.9cm) high, 7" (17.8cm) deep. high, 7" (17.8cm) long, 9" (22.9cm) (40.6cm) 60Hz. 16" 115V, LA BOUNTY Precisely aligns individual steel stamps to help steel stamps aligns individual Precisely For Precision Alignment When Marking Barrels When Alignment Precision For #319-056-001AU #319-056-002AU #319-056-003AU #319-056-000AU contains gold powder, liquid base, cleaner, (3) 2" (5.1cm) di (3) 2" (5.1cm) liquid base, cleaner, gold powder, Kit contains SPECS: instructions. and complete ameter cloths, fill. Gives production guns a personalized appearance. Complete kit guns a personalized fill. Gives production instructions and includes enough gold comes with easily followed gun work, but definitely jobs. Made for many powder to do many, not limited to guns; will work on any metal. (6cm) long x 3 rect positioning on workpiece prior to tapping with your hammer. positioning on workpiece prior to tapping with your hammer. rect Accepts barrels up to 1 barrels SPECS: SPECS: ensure characters are straight and evenly spaced characters are ensure Allen on barrels. when stamping caliber designations character accurate allow adjustment for head screws Machined port looking results. spacing, so you get truly professional cor ensure to head stamp first the unobstructed view of an allows #351-004-780AU #521-104-000AU #351-001-500AU #351-003-021AU CFM at 50 psi, 120 psi maximum. Includes; handpiece, three tool holders, tool holders, three 50 psi, 120 psi maximum. Includes; handpiece, CFM at air lines, and instructions. air filter/regulator, control, foot height 7 height - Get professional - Get professional SYSTEM 3 AIR ENGRAVER with handpiece Comfortable quickly. results lets you do carv tool holders quick-change and metal removal. ing, fine line engraving by your compressor. Powered SPECS: SPECS: SPECS: In just a few hours even hours a few - In just GRAVERMEISTER lines; clean, sharp can be cutting a beginner A minia pros. for time saver a tremendous pre with jack-hammer self-contained ture, power and speed; cut stroke of cise control background heavy lines or remove delicate material. SPECS: 3 Power Cord, Tubing, Connection Includes: Power Unit, Hand Tool, gravers.. most standard Gravers. Accepts - Precision, stable work- stable - Precision, BLOCK ENGRAVING pivot fully adjustable The engraving. all for holder needle bearings that drag with radial and thrust any the block to absorb mass of use the entire and blued jaws, Heat-treated, shock and force. and one pivot), to (one fixed two adapter plates, The block attachments. engraving standard take Furnished plated. chrome hard are ball and crown attachments. with rubber holding ring and opening. - order on the web 8.99 $ 7.99 28.99 122.99 $ 12.99 $ 78.99 $ 74.99 $ 396.99 " (4.8mm) " (4.8mm) 16 brownells.com / 3

��

�� ab 9D7D99 8C17B99 9D6I99 ", " (3.2cm) clamp " (3.2cm) 16 ", 4 / 8 - - / 6C60K99 3 1 / " (1.6mm). 4H10Q99 7 8 ab / We asked James B. Meek, au James B. asked We 1 JAMES MEEK’S JAMES Author Of Art Of Engraving Of Author " x 8C266Q99 " x 1 8 2 Basic Engraver Set Selected By Set Engraver Basic /

/ thor of The Art Of Engraving for for The Art Of Engraving thor of This is what his recommendations. all the 90% of “Perhaps he wrote: 5 1 Nos. 50 and 54. 9 gravers 9 gravers 50 and 54. - Nos. Round �� " (7.3cm) arm, 1 " (7.3cm) Set to any angle by turning " (11.1cm) long. Shank tapers from " (11.1cm) long. Shank tapers from 8 8 / 7 / 3 KFM-1A BEGINNER’S KIT BEGINNER’S KFM-1A, Luxo Fluorescent Tube, T-9 8K111D99 James B. Meek Beginner’s Kit, James B. 8K72Q99 Beginner’s Engraving Kit, Deluxe 5 Practice Plates, Model 642, 2 1 Model 643, Graver Sharpener, " (18.4cm) x 3" (7.6cm) x x 3" (7.6cm) " (18.4cm) 4 / 1 b OOL & CHISEL HANDLES - Specially ENGRAVING ACCESSORIES ENGRAVING Magnifies - Illuminates, Illuminates, - Magnifies Approximately .010" (.25mm) diameter drilled .010" Approximately 45" (114.3cm) long adjustable arm. 5" (12.7cm) dia. lens. long adjustable arm. 5" (12.7cm) 45" (114.3cm) Approximately 4 Approximately 3" (7.6cm) base, 2 3" (7.6cm) Steel. 7 The Art of Engraving to get you started. The Art of Brings Hard Jobs Into Focus Into Jobs Hard Brings " (1.6mm). Blanks are 4" (10.2cm) long. Steel. 4" (10.2cm) are Blanks " (1.6mm). Nos. 50 and 54 are needed for lettering on high relief. lettering on high relief. needed for Nos. 50 and 54 are Round LUXO LAMPLUXO Serves double-duty as an illuminat double-duty as Serves 16 / 1 SPECS: SPECS: ed magnifier and as a shadow-free fluo a shadow-free as ed magnifier and ground 5" diameter, bench light. rescent optical glass, magnifying and polished, all-metal, the center of lens set in the on 45" long, internal lamp head. Suspended doughnut-shaped, can be moved into high adjustable arm, the head spring-tensioned magnifier. use as illuminated for or lowered light only, position for working 13", ideal for a working distance of at 1-3/4X magnification switch On/off or checkering. small parts, engraving on hard-to-see or bench to lamp secures clamp metal duty Heavy head. lamp in tube included. desk top. Fluorescent #538-200-009AU #538-100-002AU to scroll work in engraving can be done with the following tools”. Point can be done with the following work in engraving scroll Fine detail is cut with 0 Point. Knife No. 4 will cut most scrolls. Graver detail. The Square is perhaps the most widely used, No. 2 is also for Nos. 36 and 37, can also be sharpened as a point, or a chisel, Flat and Flat Blanks; Kit contains: Point - Nos. 0 and 4; Square - (2) GlenSteel No. 2; and 39; Knife - Nos. 36 - the engraving Beginner’s Engraving Kit includes all of total. Deluxe Meek’s authoritative Mr. a copy of the Beginner’s kit, plus tools from book SPECS: SPECS: #100-008-129AU #080-561-000AU #249-640-643AU #249-640-642AU #084-001-005AU #360-368-801AU shaped for your own, unique tools. Nicely finished your own, shaped for metal ferrules. with sturdy - Made from - Made from PLATES PRACTICE ENGRAVER’S “killed” aluminum plate, steel quality, drawing Soft, easily. Works age hardening. to prevent finish.a matte SPECS: T SPECIAL SPECS: 3. Sold in Pak of hole. 1" = 2.5cm. - SHARPENER GRAVER index. SPECS: head. Nickel plated. head. Nickel

2 ------/ 1 17.99 35.99 33.99 52.99 38.99 54.99 54.99 34.99 49.99 $ 51.99 $ 75.99 $ 11.99 $ 53.99 $ 51.99 $ 54.99 $ 35.99 $ 49.99 $ 49.99 PRICE X at 4" (10.2cm). X at 2 6C41I99 / 8K44K99 6C67E99 8K52N99 6C42A99 1 6C43C99 �� - �� X at 14" (35.6cm); No. 5, 2 (35.6cm); 14" X at 4 �� / 3 5E49P99 5E37H99 5E47C99 5E46J99 5E48B99 5E50P99 5E31H99 5E30N99 5E31B99 5E32Q99 OptiVISOR 5E15Q99 5E9J99 LPI " (12.7mm) wide. Cutting area: 6" (15.2cm) 6" (15.2cm) wide. Cutting area: " (12.7mm) 2 / 1 No. 10, 3 No. 6" (15.2cm); X at 4 / 3 EXTRA LENS PLATES 20 (#00) 25 (#00) 30 (#0) 40 (#1) 50 (#2) 75 (#4) 800-741-0015 OptiLOUPE, No. 2 Lens Plate, No. 3 Lens Plate, No. 5 Lens Plate, No. 7 Lens Plate, No. 10 Lens Plate, New-style Comfort Band, (plastic tab attachment), No. 2 OptiVISOR, No. 3 OptiVISOR, No. 5 OptiVISOR, No. 7 OptiVISOR, No. 10 OptiVISOR,

ab X at 20" (51.0cm); No. 3, 1 20" (51.0cm); X at 2 / 1 METAL CHECKERING FILES CHECKERING METAL DONEGAN OPTICAL DONEGAN

Screw-on attachment. Screw-on 8" (20.3cm) length x 8" (20.3cm) STOCK # STOCK The only way to get true, accurate line spacing when checker line spacing The only way to get true, accurate This tough, durable material is practi - This tough, durable material VISOR ABS HI-IMPACT GLASSOPTICAL and polished to precise - Ground LENSES REGULARFITS OVER GLASSES with them off - No need to take GENUINE LEATHER COMFORT BAND - Padded with orthope COMFORT GENUINE LEATHER Adjustable pivots make the OptiVISOR unique - and unique OptiVISOR the make pivots Adjustable - IT TILTS nonconductive HEADBAND - Of electrically CONFORMING DIAL ADJUSTABLE CONTINUOUS CONTINUOUS ADJUSTABLE DIAL

" (12.7mm). 2 Continuous Headband; Dial Adjustable Dial Headband; Continuous / 1 Dead-On Spacing For Grip Frames, Hammer Spurs and More Spurs and Hammer Frames, Grip Dead-On Spacing For #255-002-020AU #255-010-100AU #255-303-001AU #255-003-030AU #255-005-050AU #255-007-070AU #255-001-600AU

x Orders: SPECS: SPECS: ous lines as the guide. Once the pattern is fully laid out, bring to final is fully ous lines as the guide. Once the pattern depth with a 60° needle file. ing backstraps, triggerguards, grip frames, ribs and hammer spurs; grip frames, ribs and triggerguards, ing backstraps, gripping surface is needed. Finer cuts give a an improved anywhere and light distortion. Layout your glare to reduce effect nice matting Guide), establish Checkering our .45 master lines (or use a guide like teeth each time using the previ by moving the file a few the pattern SPECS: SPECS: Easily attached to any OptiVISOR. - Easily attached OPTILOUPE way. Pivots out of Gives up to 6X magnification. #255-003-000AU #255-000-000AU #255-005-000AU #255-007-000AU #080-310-431AU #080-310-451AU #080-310-411AU #080-310-421AU #080-310-401AU #080-000-177AU #255-002-000AU No. 7, 2 ; No. 8" (20.3cm) X at SPECS: No. 2, 1 SPECS: optical standards. Beveled edges and mounted in interchangeable in interchangeable Beveled edges and mounted optical standards. powers are computed prismatic plastic frames. Five scientifically use with any OptiVISOR. for available the OptiVISOR. cally indestructible, yet always keeps its new appearance. keeps cally indestructible, yet always dic felt, making the OptiVISOR the most comfortably worn magni worn making the OptiVISOR the most comfortably dic felt, fier available. fortable position. Total weight just 4 oz. So light you hardly know So light you hardly weight just 4 oz. position. Total fortable it’s there. the most handy magnifier yet. It’s up, out of the way of normal vision the way of magnifier yet. It’s up, out of the most handy it for fingertips when you need your at and there when not in use, the job. clarity back at magnified pinpoint com in a natural, the scope locate Designed to fit and ABS material. ple twist of the adjusting dial changes head the adjusting dial ple twist of mechanism is self-locking Sealed-in size. comfort. more better balance and even Gives and trouble-free. Specially formed to fit. A sim formed - Specially HEADBAND STEEL LETTERS & FIGURES ENGINE TURNING KIT Stamp Your Own Combination Of Numbers & Specs In Softer Steels & Metals Save & Get Everything You Need Hand cut and taper-ground for making “factory perfect” impressions on custom rifle barrels and Two money saving kits that have every- Gun Bluing other metal objects. Made from the finest quality steel, selected for its proven ability to withstand thing needed to produce an attractive, jew- hard use, then heat-treated to three distinct hardnesses. The character end is hardened to Rc 62 to eled finish on hammers, triggers, rifle bolts, prevent chipping. Hammer end is crowned and hardened to prevent mushrooming, and the center etc. Select the kit that best meets your needs WHY GUN BLUING? is hardened to transmit the hammer blow. Each stamp is individually inspected and marked with and save the time and cost of buying indi- index on thumb side so you’ll always know which way the character is facing. vidual pieces. The Standard Kit contains two Sets of letters consist of 27 characters, including period. Sets of figures consist of nine characters of our E/T Brush sets and a container of 120 No other activity or line of work in a gun shop or from 0 to 8, the 6 also being used for the 9. Packed in sturdy wooden box with lid. ab grit silicon carbide abrasive; the Deluxe Kit adds our E/T Brush Holder sporting goods store teaches the mechanics of a gun 1 3 SPECS: Steel Stamps stocked in /16" (1.6mm) and /32" (2.4mm) sizes. The characters are cut into the end Assembly that gives just the right amount of brush pressure against the better than bluing. To reblue a gun, you have to com- 1 3 METAL WORK METAL of a steel bar measuring /4" (6.4mm) square x 2 /8" (6cm) long. Purchase as sets or by the individual piece. work piece. Use the Standard Kit if you primarily work on flat surfaces. pletely dismantle it piece-by-piece, and each of the hun- The Deluxe Kit produces a great finish on flat or curved surfaces. To get STK# 1/16" STK# 3/32" CHARACTER STK# 1/16" STK# 3/32" CHARACTER STK# 1/16" STK# 3/32" CHARACTER the best results, the kits should be used in a drill press. ab dreds of varieties of guns has its own peculiarities. After #990-501-101AU #990-501-201AU A #990-501-114AU #990-501-214AU N #990-501-130AU #990-501-230AU #0 SPECS: Each kit contains twelve E/T brushes, 24 O-rings, two 4" lengths of you have handled so many guns, the whole theory of a #990-501-102AU #990-501-202AU B #990-501-115AU #990-501-215AU O #990-501-131AU #990-501-231AU 1 heat shrink tubing, one 4 oz. container 120 grit Silicon Carbide Abrasive, gun’s mechanical operation becomes ingrained in your #990-501-103AU #990-501-203AU C #990-501-116AU #990-501-216AU P #990-501-132AU #990-501-232AU 2 a 1 oz. bottle of Do-Drill and complete instructions. The deluxe Kit adds mind, never to be lost. Further, continued handling of the the E/T Brush Holder. #990-501-104AU #990-501-204AU D #990-501-117AU #990-501-217AU Q #990-501-133AU #990-501-233AU 3 more popular guns soon leads the gunsmith to know, #080-558-100AU Std Engine Turning Kit, 8K49C99 �� $ 57.99 #990-501-105AU #990-501-205AU E #990-501-118AU #990-501-218AU R #990-501-134AU #990-501-234AU 4 almost automatically and without looking, which parts #080-558-101AU Deluxe Engine Turning Kit, 8K65N99 �� 82.99 #990-501-106AU #990-501-206AU F #990-501-119AU #990-501-219AU S #990-501-135AU #990-501-235AU 5 are worn and need to be replaced. #990-501-107AU #990-501-207AU G #990-501-120AU #990-501-220AU T #990-501-136AU #990-501-236AU 6 & 9 There is also a money-making feature—not only is #990-501-108AU #990-501-208AU H #990-501-121AU #990-501-221AU U #990-501-137AU #990-501-237AU 7 bluing fairly profitable, but it also gives the dealer or gun- #990-501-109AU #990-501-209AU I #990-501-122AU #990-501-222AU V #990-501-138AU #990-501-238AU 8 smith an opportunity to become better acquainted with #990-501-110AU #990-501-210AU J #990-501-123AU #990-501-223AU W #990-000-001AU #990-000-002AU & his shooting customers. Nothing pleases a gunnut more #990-501-111AU #990-501-211AU K #990-501-124AU #990-501-224AU X #990-501-140AU #990-501-140AU Period ENGINE TURNING BRUSHES than a gunsmith making his favorite gun look like new. #990-501-112AU #990-501-212AU L #990-501-125AU #990-501-225AU Y Produce Beautiful, Deep Patterns As a result, he is inclined to return to the gunsmith who #990-501-113AU #990-501-213AU M #990-501-126AU #990-501-226AU Z With Minimal Trouble; worked such miracles—for bluing does seem to be magic

1 #990-600-100AU /16" Figure Stamp Set, 9Z20C99 �� $ 35.99 Customer Recommended! for the uninitiated. So as sights and scopes, slings and gun 3 cases are needed, the sportsman not only buys from the #990-600-200AU /32" Figure Stamp Set, 9Z29B99 �� 34.99 Use for engine turning rather

JEWELING 1 man who did up his gun, he brings his friends along, too. #990-500-100AU /16" Letter Stamp Set, 9Z63B99 �� 103.99 than abrasive tips. Brush wires follow the contours of rounded gun 3 parts better, and does a superb job on flat surfaces, with long tool #990-500-200AU /32" Letter Stamp Set, 9Z88J99 �� 95.99 The original cost of setting up a bluing shop is life. Use Engine Turning Abrasive and Do-Drill as explained in the not great, nor is it necessary to buy a lot of stuff. Bluing — Advise # — Single Letter or Figure Stamp, 9Z3I99 ��$ 6.99 listing elsewhere in this section. ab Steel Stamps are intended for softer steels, barrels, etc. DO NOT use on hardened or plated steels, knife blades, tough alloys. Misuse voids guarantee. 3 1 tanks, burners, some bluing salts, cleaner, polish, some SPECS: Brush diameter /16" (4.8mm), .005" diameter (.13mm) wire, /8" 7 (3.2mm) shaft. 1 /8" (4.4cm) overall. wheels—and you’re in business. From then on buy as you #080-558-003AU 3 Engine Turning Brushes, 8K7Q99 ��$ 9.99 need. Don’t buy unless you do need. ENGINE TURNING BRUSH HOLDER - So far as bluing salts are concerned, we make no MORELANDS PRECISION CUSTOM MADE NAME STAMPS Spring-loaded plunger assembly with claim that our salts are superior to anyone else’s. We do just the right amount of “give” keeps brush bristle pressure constant have Bureau of Standards reports that prove some salts BARREL STAMPING TOOL Stamp Barrels & Other Gun Parts to produce consistent, accurate “swirls.” Fits in drill press chuck. claimed to be as good as ours simply aren’t. But let us SPECS: Machined steel. 4" (10 cm) long. For Precise Letter & Number Identify the work from your shop and not kid anybody: there are lots of other bluing salts on #080-558-001AU E/T Brush Holder, 8K36M99 �� $ 39.99 Alignment On Barrels comply with the requirements of Federal the market about as good as ours. We feel we are selling Firearms Law. Deep-impression, hand bluing salts to gunsmiths who know their business, to Precision tool spaces and aligns cut gothic letters, cut into one single metal stamps for perfectly straight stamp to ensure perfect letter alignment. ab sporting goods dealers and shooters who are past the 3 1 letters and numbers when marking SPECS: Available in /32" (2.4mm) or /8" (3.2mm). (For barrel marking, keep “sucker” stage. Why should we insult their minds with a barrels. Length adjustable slide locks size and number of characters to a minimum to ensure single-blow bunch of hooey? stamps firmly in place with easy-to- impression in the steel.) ENGINE TURNING BRUSH SET The proof of any pudding is in the eating. We guar- grasp, wing-nuts that also allow fast, easy stamp removal and instal- ORDERING: Advise: 1) Character size Stock # from table. 2) Characters lation. Stamping tool mounts to the barrel with two steel U-clamps wanted. Example: F.R.B. is six characters, 30-06 is five. antee you to be satisfied on a money-back basis. What 3 that prevent slipping and mis-alignment. Includes fifteen /32" thick Name Stamps are Special Order Items. We must receive full payment in more should be said? 1 shims and fifteen /8" thick shims for precise character spacing of advance and the order is non-cancel-lable and non-refundable. Allow High Grade Brushes, Plus Two Ways To Control Brush Spread 1 5 So, on to business. The quality of a good blue job up to thirty /4" square stamps. Fits barrels up to 1 /16" diameter. ab 6-8 weeks for delivery. Easy-to-fit, heat shrink tubing or roll-on O-rings squeeze en- depends entirely on the gunsmith doing the bluing, not SPECS: Aluminum, natural finish with steel U-bolts and hardware. 8" Not intended for hardened or plated steels, knife blades, or tough alloys. 1 5 gine turning brush bristles together so they don’t spread out. Keeps (20cm) long, 2 /2" (6.4cm) wide, 2" (5.1cm) high. Fits barrels up to 1 /16" on the salts. If you have a gunsmith who will do a mas- ENGRAVING & STAMPING ENGRAVING Misuse voids guarantee. 1 the “swirls” crisp and sharp, adding a new dimension to your jeweling diameter. Requires /4" square stamps. terful piece of polishing, with all surfaces true and bright, STOCK # CHAR. PRICE STOCK # CHAR. PRICE capabilities; increases brush life, too! ab #100-004-268AU Barrel Stamping Tool, 3B181B99 �� $ 203.99 3 1 corners sharp, without funneled screw holes or ground- 3 1 SPECS: Set includes: (6) /16" (4.8mm) dia. brushes; (12) /4" (6.3mm) dia. /32" /8" O-rings; (1) 4" (10cm) length of heat shrink tubing. off screw heads—if he is careful to clean the gun properly #990-003-332AU 3 $ 89.69 #990-003-108AU 3 $ 96.40 #080-558-000AU E/T Brush Set, 8K18E99 ��$ 23.99 before bluing—if he will follow the instructions that go #990-004-332AU 4 $ 102.45 #990-004-108AU 4 $ 108.97 with anybody’s salts—well, he’ll get bluing jobs that are #990-005-332AU 5 $ 113.72 #990-005-108AU 5 $ 120.87 out of this world. #990-006-332AU 6 $ 129.64 #990-006-108AU 6 $ 139.74 Because of our constant association with many #990-007-332AU 7+* $ 230.00 #990-007-108AU 7+* $ 265.00 CRATEX ABRASIVE RODS ENGINE TURNING ABRASIVE * 7 or more, per ea. thousands of gunnuts, gunsmiths, gun dealers, and man- No Messy Oil ufacturers in the bluing business, we feel we can give you For Deeper, More Beautiful Jewels For Cleaner Bolt Jeweling the service you deserve. If we can’t after all these years, Engine Turning designs on bolts, hammers, Medium grit rods for bolt better we should go to selling raincoats and straw hats! jeweling. The close size control triggers, plates, and other parts can often be Bluing can be fun and profitable—full-time or part- made much deeper and the pattern of the dama- means your “swirls” will be the same, time after time. SPECS: 1 pound (.454kg) container. 120 grit. 3 1 scening more complete by polishing with a thin SPECS: /16" (4.8mm) or /4" (6.3mm) diameter, 6" (15.2cm) long. time. Shooters are always looking for gunsmiths who will 3 paste of abrasive powder mixed with a good cut- #080-537-120AU 120 Grit Silicon Carbide, 5L8K99 ��$ 14.99 #190-036-002AU /16" x 6" Abrasive Rod, 9A8F99 ��$ 9.99 give them honest work. 1 ting oil, like Brownells Do-Drill™. ab #083-007-016AU 16 oz. Do-Drill, 5L13J99 �� 15.99 #190-046-002AU /4" x 6" Abrasive Rod, 9A8K99 �� 12.99 METAL FINISHING METAL GUARANTEED. FOREVER.

PAGE 390 SINCE 1939 Office/Tech: 641-623-5401