Questions About Solderability... What Is Solderability? Solderability Refers to How Easy a Metal Is to Solder To

Total Page：16

File Type：pdf, Size：1020Kb

® Questions about solderability... What is solderability? Solderability refers to how easy a metal is to solder to. Some metals like copper and tin are easy to solder to. Other metals like brass and steel are difficult to solder to. Please refer to the metals solderability chart at the bottom of this section. When a metal oxidizes it becomes harder to solder. Due to oxidation, an easy to solder metal can become hard to solder. Kester makes products to remove the oxidation off different metal surfaces (i.e. Copper-Nu, Nickel-Nu, Solder-Nu). We are doing die attach to a gold surface. What kind of solder do we need? Gold will dissolve in standard tin-lead solders. If there is too much gold, the joint will become brittle due to the tin/gold intermetallics. For people soldering to solid gold, such as in die attach, they need a gold bearing solder. We do not have gold bearing solders. We are soldering to gold and we heard that we need a silver solder. Is this true? This is a common misconception. You need a small amount of silver in your solder if you are soldering to silver. The two most common situations are silver plating on component leads and silver palladium substrates. In both these cases the Sn62 alloy should be used. Metal Solderability Chart & Flux Selector Guide Oraganic Inorganic No Clean Non-Acivated Mildly Activated Fully Activated Metal Surfaces Solderability Fluxes Fluxes Fluxes Rosin Fluxes Rosin Fluxes Rosin Fluxes Water Soluble Water Soluble Not Platinum 186 Recommended Gold for Electrical Copper 958 2235 Easy to Soldering Tin 135 186-18 Solder Solder 959 1544 Palladium Silver 1588 Nickel 1429 Brass Cadmium Lead Less Easy Bronze to Solder 715 Rhodium Beryllium 2331-ZX Copper Nickel-Iron Difficult Kovarl to Solder Zinc Mild Steel 817 Chromium Very Difficult Inconel To Solder 3350 Monel Stainless Stee Copyright ©1996-2002 Kester. All rights reserved. .

Copy Link

Recommended publications

Treatise on Combined Metalworking Techniques: Forged Elements and Chased Raised Shapes Bonnie Gallagher
Rochester Institute of Technology RIT Scholar Works Theses Thesis/Dissertation Collections 1972 Treatise on combined metalworking techniques: forged elements and chased raised shapes Bonnie Gallagher Follow this and additional works at: http://scholarworks.rit.edu/theses Recommended Citation Gallagher, Bonnie, "Treatise on combined metalworking techniques: forged elements and chased raised shapes" (1972). Thesis. Rochester Institute of Technology. Accessed from This Thesis is brought to you for free and open access by the Thesis/Dissertation Collections at RIT Scholar Works. It has been accepted for inclusion in Theses by an authorized administrator of RIT Scholar Works. For more information, please contact [email protected]. TREATISE ON COMBINED METALWORKING TECHNIQUES i FORGED ELEMENTS AND CHASED RAISED SHAPES TREATISE ON. COMBINED METALWORKING TECHNIQUES t FORGED ELEMENTS AND CHASED RAISED SHAPES BONNIE JEANNE GALLAGHER CANDIDATE FOR THE MASTER OF FINE ARTS IN THE COLLEGE OF FINE AND APPLIED ARTS OF THE ROCHESTER INSTITUTE OF TECHNOLOGY AUGUST ( 1972 ADVISOR: HANS CHRISTENSEN t " ^ <bV DEDICATION FORM MUST GIVE FORTH THE SPIRIT FORM IS THE MANNER IN WHICH THE SPIRIT IS EXPRESSED ELIEL SAARINAN IN MEMORY OF MY FATHER, WHO LONGED FOR HIS CHILDREN TO HAVE THE OPPORTUNITY TO HAVE THE EDUCATION HE NEVER HAD THE FORTUNE TO OBTAIN. vi PREFACE Although the processes of raising, forging, and chasing of metal have been covered in most technical books, to date there is no major source which deals with the functional and aesthetic requirements
[Show full text]
MIL-STD-202G METHOD 208H SOLDERABILITY 1. PURPOSE. the Purpose of This Test Method Is to Determine the Solderability of All
MIL-STD-202G METHOD 208H SOLDERABILITY 1. PURPOSE. The purpose of this test method is to determine the solderability of all terminations which are normally joined by a soldering operation. This determination is made on the basis of the ability of these terminations to be wetted by solder and the predictability of a suitable fillet resulting from solder application. These procedures will verify that the pre-assembly lead finish provides a solderable surface of sufficient quality to enable satisfactory soldering. 2. PROCEDURE. The solderability test shall be performed in accordance with ANSI/J-STD-002 “Solderabiilty Tests for Component Leads, Terminations, Lugs, Terminals and Wires” and herein. The following details and exceptions shall apply: 2.1 Contractual agreements. The contractual agreements statement in ANSI/J-STD-002 shall not apply. Any exceptions to the requirements specified in ANSI/J-STD-002 and this test method shall be documented in the individual military procurement document or approved by the procuring military activity. 2.2 Coating durability. The coating durability category (from ANSI/J-STD-002) shall be as follows: a. Category 2 - for stranded wire (1 hour ±5 minutes steam aging with insulation removed). b. Category 3 - for all other components (8 hours ±15 minutes steam aging). 2.3 Test method. The test method used (from ANSI/J-STD-002) shall be as follows: a. Test A - for through-hole mount and surface mount leaded components, solid wire less than .045 inch diameter and stranded wire 18 AWG or smaller. If not otherwise specified in the procurement document, angle of immersion for surface mount leaded components shall be 90°.
[Show full text]
Sn95/Sb5 – Organic Acid 3% Core
Technical Data Sheet Sn95/Sb5 – Organic Acid 3% Core NOMINAL COMPOSITION Tin 94% Min Lead 0.1% Max Arsenic 0.01% Max Antimony 4.5% 5.5 Cadmium 0.005% Max Iron 0.04% Max Copper 0.08% Max Aluminum 0.005% Max Zinc 0.005% Max Silver 0.015% Max Bismuth 0.15% Max Flux – 3% Organic Acid Core by weight PHYSICAL PROPERTIES Solder Alloy Color White Melting Point (Solidus) 450°F (233°C) Flow Point (Liquidus) 464°F (240°C) Specific Gravity 7.26 Density (Lbs/in3) 0.263 Bulk Room Temperature Tensile Strength (PSI) 5,900 Flux Type Water Soluble Organic Acid Physical State Solid Melting Point 250°F (120°C) Chloride Content 4% SOLDERING CHARACTERISTICS Sn95/Sb5 is a general-purpose solder used in applications involving soldering of copper and copper alloys and/or ferrous base alloys where use of lead containing solder is not permitted. This soft solder may be used in applications involving higher service temperatures. Typical applications for this alloy include copper components in air conditioning industry. This alloy is also recommended in applications involving food handling or drinking water components where use of lead containing alloys is not permitted. Antimony bearing alloys are not recommended in soldering of brass parts due to formation of a brittle Sb-Zn inter-metallic. This flux-cored solder can be used on difficult to solder materials where rosin based fluxes and electronic grade organic fluxes are not strong enough. It has been used effectively in many non-electronic applications such as lamps, fuses, and jewelry. The flux is active on copper, brass, bronze, steel, nickel, and stainless steel.
[Show full text]
Repoussé Work for Amateurs
rf Bi oN? ^ ^ iTION av op OCT i 3 f943 2 MAY 8 1933 DEC 3 1938 MAY 6 id i 28 dec j o m? Digitized by the Internet Archive in 2011 with funding from Boston Public Library http://www.archive.org/details/repoussworkforamOOhasl GROUP OF LEAVES. Repousse Work for Amateurs. : REPOUSSE WORK FOR AMATEURS: BEING THE ART OF ORNAMENTING THIN METAL WITH RAISED FIGURES. tfjLd*- 6 By L. L. HASLOPE. ILLUSTRATED. LONDON L. UPCOTT GILL, 170, STRAND, W.C, 1887. PRINTED BY A. BRADLEY, 170, STRAND, LONDON. 3W PREFACE. " JjJjtfN these days, when of making books there is no end," ^*^ and every description of work, whether professional or amateur, has a literature of its own, it is strange that scarcely anything should have been written on the fascinating arts of Chasing and Repousse Work. It is true that a few articles have appeared in various periodicals on the subject, but with scarcely an exception they treated only of Working on Wood, and the directions given were generally crude and imperfect. This is the more surprising when we consider how fashionable Repousse Work has become of late years, both here and in America; indeed, in the latter country, "Do you pound brass ? " is said to be a very common question. I have written the following pages in the hope that they might, in some measure, supply a want, and prove of service to my brother amateurs. It has been hinted to me that some of my chapters are rather "advanced;" in other words, that I have gone farther than amateurs are likely to follow me.
[Show full text]
Hercules Jewelry Project
Hercules Knot Jewelry Series I thoroughly enjoyed my wire wrapping jewelry projects, but in the course of researching and building the class, I was inspired to learn real metalsmithing. I’ve been assembling earrings and necklaces for decades, but suddenly I really wanted to solder, and set gems, and fabricate! Fortunately, my good friend Fjorlief InHaga is a brilliant artisan, and she’s been teaching me and letting me use her studio. THE HERCULES KNOT aka HERAKLES, Reef Knot or Square Knot This motif represents strength and came to be associated with marriage. Brides wore their belts tied this way (see my paper on Roman Weddings). It was a common motif in the Greco-Roman world though the Republic and Early – Mid Empire. 1 2 3 Above, gold bracelet and ring from the 1st century BCE – 2nd CE. Silver mirror, 4th century CE. I imagine this would have been a lovely wedding present. Below: Necklaces dated to the 2nd-3rd century, an armband (#6), and rings from 5rd century BCE to 3rd CE . I have included only a small number of the large quantity of eXtant artifacts. Combined with the variations in assembly technique and clasps, the abundance of pieces shows that the Hercules Knot was a style that was widespread and made by many different artisans. 4 5 6 7 8 9 10 For my first project, I wanted to duplicate the look of these early Imperial necklaces of emerald and gold. For cost purposes, I used brass and glass, which was a commonly-used substitute for stones in period.
[Show full text]
Low Melting Temperature Sn-Bi Solder
metals Review Low Melting Temperature Sn-Bi Solder: Effect of Alloying and Nanoparticle Addition on the Microstructural, Thermal, Interfacial Bonding, and Mechanical Characteristics Hyejun Kang, Sri Harini Rajendran and Jae Pil Jung * Department of Materials Science and Engineering, University of Seoul, 163, Seoulsiripdae-ro, Dongdaemun-gu, Seoul 02504, Korea; [email protected] (H.K.); [email protected] (S.H.R.) * Correspondence: [email protected] Abstract: Sn-based lead-free solders such as Sn-Ag-Cu, Sn-Cu, and Sn-Bi have been used extensively for a long time in the electronic packaging field. Recently, low-temperature Sn-Bi solder alloys attract much attention from industries for flexible printed circuit board (FPCB) applications. Low melting temperatures of Sn-Bi solders avoid warpage wherein printed circuit board and electronic parts deform or deviate from the initial state due to their thermal mismatch during soldering. However, the addition of alloying elements and nanoparticles Sn-Bi solders improves the melting temperature, wettability, microstructure, and mechanical properties. Improving the brittleness of the eutectic Sn-58wt%Bi solder alloy by grain refinement of the Bi-phase becomes a hot topic. In this paper, literature studies about melting temperature, microstructure, inter-metallic thickness, and mechanical properties of Sn-Bi solder alloys upon alloying and nanoparticle addition are reviewed. Keywords: low-temperature solder; Sn-58wt%Bi; melting temperature; microstructure; mechani- Citation: Kang, H.; Rajendran, S.H.; cal property Jung, J.P. Low Melting Temperature Sn-Bi Solder: Effect of Alloying and Nanoparticle Addition on the Microstructural, Thermal, Interfacial Bonding, and Mechanical 1. Introduction Characteristics. Metals 2021, 11, 364.
[Show full text]
Weights of Various Metals in Pounds Per *Cubic Foot
Weights of Various Metals in Pounds Per *Cubic Foot Aluminum 168.48 Copper 559.87 Manganese 463.10 Silver 654.91 Antimony 419.99 Gold 1206.83 Mercury 849.00 Stainless Steel (18-8) 494.21 Beryllium 113.70 Gun Metal (Aver.) 544.00 Molybdenum 637.63 Steel, Cast/Rolled 490.00 Bismuth 611.00 Iridium 1396.00 Monel Metal 556.00 Tin 455.67 Brass (Approx.) 535.68 Iron 491.09 Nickel 555.72 Titanium 283.39 Bronze, Alum. 481.00 Iron, Cast Grey 442.00 Osmium 1402.00 Tungsten 1204.41 Bronze (Approx.) 541.00 Iron, Wrought 480.00 Palladium 712.00 Vanadium 374.97 Cadmium 540.86 Iron, Slag 172.00 Platinum 1339.20 Zinc 445.30 Chromium 428.00 Lead 707.96 Rhodium 755.00 *1728 CU. IN. PER CU. FT. Cobalt 552.96 Magnesium 108.51 Ruthenium 765.00 Weights of Other Materials in Pounds Per *Cubic Foot Acids, Muriatic, 40% 75.00 Earth, Common Loam 75.00-90.00 Maple, Hard 43.00 Rubber, Goods 94.00 Acids, Nitric, 91% 94.00 Earth, Dry/Loose 76.00 Maple, White 33.00 Sand, Clay & Earth, Dry 100.00 Acids, Sulphuric, 87% 112.00 Earth, Dry/Packed 95.00 Marble 170.00 Sand, Clay & Earth, Wet 120.00 Alcohol, 100% 49.00 Earth, Mud/Packed 115.00 Masonry, Rubble 130.00-150.00 Sand, Pure Quartz, Dry90.00-106.00 Asbestos 153.00 Elm, White 45.00 Masonry, Ashlar 140.00-160.00 Sandstone, Blustone 147.00 Ash, White, Red 40.00 Fats 58.00 Mortar 100.00 Slate 175.00 Asphaltum 81.00 Fir, Douglas 30.00 Mud, River 90.00 Snow, Freshly Fallen 10.00 Basalt 184.00 Fir, Eastern 25.00 Oil, Kerosene 52.00 Snow, Wet 50.00 Brick, Paving 150.00 Flour, Loose 28.00 Oil, Mineral 57.00 Soap Stone, Tall 169.00 Brick, Com.
[Show full text]
Major Causes of Solder Cracks Applications and Boards That Specially Require Solder Crack Countermeasures Comparison of 2 Soluti
Solder Crack Countermeasures in MLCCs Outline This page introduces major causes and countermeasures of solder crack in MLCCs (Multilayer Fig. 1: Appearance of a solder crack Ceramic Chip Capacitors). (cross-section) Major causes of solder cracks Solder cracks on MLCCs developed from severe usage conditions after going on the market and during manufacturing processes such as soldering. Applications and boards that specially require solder crack countermeasures Solder cracks occur mainly because of thermal fatigue due to thermal shock or temperature cycles or the use of lead-free solder, which is hard and fragile. TDK offers following MLCC products as solder crack countermeasures. 1) Metal terminals “disperse” thermal shock : 2) Equipped with resin layers that absorb stress applied on solder MEGACAP joints and resistant to dropping: Soft termination Comparison of 2 solutions: Summary of “Solder Crack Countermeasures in MLCCs” Major causes of solder cracks Solder cracks on MLCCs developed from severe usage conditions Fig. 2: Major causes of solder cracks and their impact after going on the market and during manufacturing processes such as soldering. The following causes can be listed as the major cause of solder cracks. (1) Thermal shock (heat shock), heat fatigue caused by temperature cycle Solder cracks occur when heat stress is applied to a solder joint due to the difference in the thermal coefficients of the MLCC and PCB, in an environment in which changes between high temperatures and low temperatures are repeated. In addition, it can also occur when temperature control is insufficient during the process of soldering. (2) Lead-free solder Lead-free solder, which started to be used due to environmental considerations, has properties of being rigid and fragile, and has a higher risk of solder cracks compared to conventional eutectic solder; therefore, caution is required when using it.
[Show full text]
The Periodic Table of Elements
The Periodic Table of Elements 1 2 6 Atomic Number = Number of Protons = Number of Electrons HYDROGENH HELIUMHe 1 Chemical Symbol NON-METALS 4 3 4 C 5 6 7 8 9 10 Li Be CARBON Chemical Name B C N O F Ne LITHIUM BERYLLIUM = Number of Protons + Number of Neutrons* BORON CARBON NITROGEN OXYGEN FLUORINE NEON 7 9 12 Atomic Weight 11 12 14 16 19 20 11 12 13 14 15 16 17 18 SODIUMNa MAGNESIUMMg ALUMINUMAl SILICONSi PHOSPHORUSP SULFURS CHLORINECl ARGONAr 23 24 METALS 27 28 31 32 35 40 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 POTASSIUMK CALCIUMCa SCANDIUMSc TITANIUMTi VANADIUMV CHROMIUMCr MANGANESEMn FeIRON COBALTCo NICKELNi CuCOPPER ZnZINC GALLIUMGa GERMANIUMGe ARSENICAs SELENIUMSe BROMINEBr KRYPTONKr 39 40 45 48 51 52 55 56 59 59 64 65 70 73 75 79 80 84 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 RUBIDIUMRb STRONTIUMSr YTTRIUMY ZIRCONIUMZr NIOBIUMNb MOLYBDENUMMo TECHNETIUMTc RUTHENIUMRu RHODIUMRh PALLADIUMPd AgSILVER CADMIUMCd INDIUMIn SnTIN ANTIMONYSb TELLURIUMTe IODINEI XeXENON 85 88 89 91 93 96 98 101 103 106 108 112 115 119 122 128 127 131 55 56 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 CESIUMCs BARIUMBa HAFNIUMHf TANTALUMTa TUNGSTENW RHENIUMRe OSMIUMOs IRIDIUMIr PLATINUMPt AuGOLD MERCURYHg THALLIUMTl PbLEAD BISMUTHBi POLONIUMPo ASTATINEAt RnRADON 133 137 178 181 184 186 190 192 195 197 201 204 207 209 209 210 222 87 88 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 FRANCIUMFr RADIUMRa RUTHERFORDIUMRf DUBNIUMDb SEABORGIUMSg BOHRIUMBh HASSIUMHs MEITNERIUMMt DARMSTADTIUMDs ROENTGENIUMRg COPERNICIUMCn NIHONIUMNh
[Show full text]
Llfltfits Paul Stanek, MST-6
COAJF- 9 50cDo/-~^0 LA-UR- 9 5-1666 Title: AGE HARDENING IN RAPIDLY SOLIDIFIED AND HOT ISOSTATICALLY PRESSED BERYLLIUM-ALUM1UM SILVER ALLOYS HVAUli Author(s): David H. Carter, MST-6 Andrew McGeorge, MST-6 Loren A. Jacobson, MST-6 llfltfits Paul Stanek, MST-6 IflllS,Ic 8-o° ,S8 si Proceedings of TMS Annual Meeting, Las Vegas, jJffilJSif—- Nevada, February 1995 as-IVUiS' i in Los Alamos NATIONAL LABORATORY Los Alamos National Laboratory, an affirmative action/equal opportunity employer, is operated by the University of California for the U.S. Department of Energy under contract W-7405-ENG-36. By acceptance of this article, the publisher recognizes that the U.S. Government retains a nonexclusive, royalty-free license to publish or reproduce the published form of this contribution, or to allow others to do so, for U.S. Government purposes. The Los Alamos National Laboratory requests that the publisher identify this article as work performed under the auspices of the U.S. Department of Energy* FotmNo.B36R5 MCTOIQimnM f\c mie hAMMr&T 10 i mi in ST26291M1 DISCLAIMER Portions of this document may be illegible in electronic image products. Images are produced from the best available original document. Age Hardening in Rapidly Solidified and Hot Isostatically Pressed Beryllium-Aluminum-Silver Alloys David H. Carter, Andrew C. McGeorge,* Loren A. Jacobson, and Paul W. Stanek Los Alamos National Laboratory, Los Alamos NM 87545 Abstract Three different alloys of beryllium, aluminum and silver were processed to powder by centrifugal atomization in a helium atmosphere. Alloy com• positions were, by weight, 50% Be, 47.5% Al, 2.5% Ag, 50% Be, 47% Al, 3% Ag, and 50% Be, 46% Al, 4% Ag.
[Show full text]
Soldering to Gold Films
Soldering to Gold Films THE IMPORTANCE OF LEAD-INDIUM ALLOYS Frederick G. Yost Sandia Laboratories, Albuquerque, New Mexico, U.S.A. Reliable solder joints can be made on gold metallised microcircuits using lead-indium solders providing certain important conditions are understood and carefully controlled. This paper reviews the three fundamental concepts of scavenging, wetting, and ageing, which are relevant when soldering to gold films. Alloys containing indium have been used for solder- sition and a body centred tetragonal space lattice. ing electronic components to thin gold films and wires Although considerable work has been addressed for at least 14 years. Braun (1, 2) investigated the to the question of clustering and phase separation potential of several multicomponent alloys based in the a field below 20°C (7, 8, 9) the practical signifi- upon the lead-tin-indium ternary alloy system. cance of this phenomenon has not yet materialised. More recently, work on lead-indium binary alloys The most commonly used alloy is the 50 weight has been reported by Jackson (3) and Yost, et al per cent indium composition which has a liquidus (4, 5, 6). In this paper we intend to define, to discuss, temperature of approximately 210°C and a solidus and to illustrate three fundamental concepts relevant temperature of approximately 185°C. Alloys in the to soldering to gold films using lead-indium solders. lead rich phase field, a, freeze dendritically by The lead-indium phase diagram, shown in Figure forming lead rich stalks. The formation of these 1, contains a wealth of useful solder alloys having dendrites causes a surface rumpling which gives the solidus temperatures which range from 156.6°C solder surface a somewhat frosty rather than a shiny (pure indium) to 327.5 °C (pure lead).
[Show full text]
Of the Periodic Table
of the Periodic Table teacher notes Give your students a visual introduction to the families of the periodic table! This product includes eight mini- posters, one for each of the element families on the main group of the periodic table: Alkali Metals, Alkaline Earth Metals, Boron/Aluminum Group (Icosagens), Carbon Group (Crystallogens), Nitrogen Group (Pnictogens), Oxygen Group (Chalcogens), Halogens, and Noble Gases. The mini-posters give overview information about the family as well as a visual of where on the periodic table the family is located and a diagram of an atom of that family highlighting the number of valence electrons. Also included is the student packet, which is broken into the eight families and asks for specific information that students will find on the mini-posters. The students are also directed to color each family with a specific color on the blank graphic organizer at the end of their packet and they go to the fantastic interactive table at www.periodictable.com to learn even more about the elements in each family. Furthermore, there is a section for students to conduct their own research on the element of hydrogen, which does not belong to a family. When I use this activity, I print two of each mini-poster in color (pages 8 through 15 of this file), laminate them, and lay them on a big table. I have students work in partners to read about each family, one at a time, and complete that section of the student packet (pages 16 through 21 of this file). When they finish, they bring the mini-poster back to the table for another group to use.
[Show full text]