Mitsubishi, Nissan, Mazda and Eunos Vehicle Communication Manual July 2010
Total Page:16
File Type:pdf, Size:1020Kb
SEE APPLICABLE COVERAGE SHEETS FOR VEHICLE APPLICATIONS Mitsubishi, Nissan, Mazda and Eunos Vehicle Communication Manual July 2010 Use in conjunction with the applicable Scanner User’s Reference Manual and Diagnostic Safety Manual. Before operating this unit, please read this manual and any applicable Scanner User’s Manual. Safety Notices .................................... Refer Diagnostic Safety Manual Quick Reference Contents Listing ... page 5 Using the Scanner Module ............... Refer to relevant User's Manual for more information Vehicle Identification Mitsubishi, Nissan, Mazda and Eunos Vehicle Communication Manual July 2010 BEFORE OPERATING THIS UNIT, PLEASE READ THIS MANUAL CAREFULLY, ALSO PAY PARTICULAR ATTENTION TO THE SAFETY PRECAUTIONS IN THIS MANUAL AND THE DIAGNOSTIC SAFETY MANUAL. Vehicle Identification The information, specifications, and illustrations in this manual are based on the latest information available at the time of publication. The SCANNER manufacturer and the vehicle manufacturers reserve the right to make equipment changes at any time without notice. Copyright © 2010 Snap-on Technologies Inc. Vehicle Identification Quick Reference Contents Detailed Contents are at the beginning of each part Part — Vehicle Identification..............................................................6 Gives you general information on vehicle identification. Information on SCANNER startup troubleshooting also is included. Part — Vehicle Connection and Diagnostics ..................................0 Mazda and Eunos .......................................................................................12 Mitsubishi ....................................................................................................30 Nissan ..........................................................................................................46 Appendix B – Vehicle Does Not Communicate With Scanner ...........76 General Note For All Vehicles All SCANNER and Reference Manual directions are as if the operator is standing at the back of the vehicle facing forward. 5 Vehicle Identification Part - Vehicle Identification Contents Vehicle Identification .............................................................................6 Entering the Vehicle Identification .......................................................7 System Selection ...................................................................................8 SCANNER Connection Message ............................................................8 Vehicle Identification After you select the desired manufacturer software the SCANNER then requires you to enter the vehicle’s ID. This is done by selecting the manufacturer, the year of the vehicle, model and engine displacement. Pressing N at any point in the first few steps lets you back up to the previous step to correct a choice. Pressing N at the final step will return to the start of the identification process. ‘AUSTRALIA’ is for vehicles that are manufactured for the Australian market and ‘USED IMPORTS’ refers to vehicles that were originally sold new in Japan and have since been exported to other countries, including Australia and New Zealand. The SCANNER does not list every model that is available but does cover the more popular vehicles that are available. CAUTION: Although every effort has been made to provide accurate information, due to the many models available and the lack of information available for these vehicles the information that is contained in the SCANNER for these Used Import vehicles may not always be accurate for the particular model being tested. 6 Vehicle Identification Entering The Vehicle Identification After you select the vehicle manufacturer, the screen displays the following message (example): SELECT MODEL YEAR MODEL: MODEL YEAR: 1983 ENGINE: Press the thumbpad or scroll the thumbwheel up or down to display the correct year for the vehicle you are testing. Then press Y to enter the model year. The display now shows the model year that you selected in the previous step and asks you to select the model name: SELECT MODEL TYPE MODEL: MAGNA MODEL YEAR: 1995 ENGINE: Press the thumbpad or scroll the thumbwheel up or down and press Y to select the model name. The display now shows the model name that you selected in the previous step and asks you to select the engine displacement by pressing the thumbpad or scrolling up or down to the correct engine, some vehicles may only have one choice: SELECT ENGINE TYPE MODEL: MAGNA MODEL YEAR: 1995 ENGINE: SCROLL TO SELECT ENGINE Press the thumbpad or scroll the thumbwheel up or down and press Y to select the engine displacement. The display now shows the engine that you selected in the previous step. Transmission and Air Conditioning Information At the end of vehicle identification, the screen may display the complete model and engine identification, similar to this: SELECT VEHICLE OPTIONS: > A/T WITH A/C A/T WITHOUT A/C M/T WITH A/C M/T WITHOUT A/C 7 Vehicle Identification Scroll arrow to select correct option of vehicle being tested and press Y. NOTE: A/T = Automatic Transmission M/T = Manual Transmission A/C = Air Conditioning If the identification is correct, press Y to store the identification in memory. If the identification is not completely correct, press N to return to the start of the identification steps. System Selection For some vehicles, the SCANNER provides engine and transmission test capabilities. After you press Y to store the identification for these vehicles, the screen will display this message: SELECT SYSTEM ENGINE ANTI-LOCK BRAKES AUTO TRANS AIRBAG (SRS) Using the thumbpad or thumbwheel, move the cursor to the desired system and press Y. The above display does not appear for vehicles without transmission tests. SCANNER Connection Message After you press Y to store the vehicle identification or after you select the engine or transmission system for testing, the screen display tells you how to connect the SCANNER to the vehicle. For example: CONNECT DL-16 ADAPTER WITH S-15 KEY TO 16-PIN CONNECTOR UNDER RH DASH. PRESS Y TO CONTINUE. Connect the SCANNER to the vehicle as per on screen instructions. After the SCANNER is connected to the vehicle, press Y to proceed to the MAIN MENU. 8 Vehicle Identification PAGE INTENTIONALLY LEFT BLANK Part 2 — Vehicle Connection and Diagnostics Contents Connecting the SCANNER to the vehicle ....................................... Special Notes on Graph Mode ........................................................ Note on Functional Tests ................................................................. Mazda and Eunos – .......................................................................... Special Notes ................................................................................... 13 Connector Types .............................................................................. 14 Engine .............................................................................................. 17 Automatic Transmission .................................................................. 23 ABS .................................................................................................. 25 SRS – Airbag .................................................................................... 26 Body Systems .................................................................................. 29 Mitsubishi – ...................................................................................... 0 Special Notes ................................................................................... 31 Connector Types ............................................................................... 33 Engine ............................................................................................... 36 Automatic Transmission ................................................................... 38 ABS .................................................................................................. 41 SRS .................................................................................................. 45 Nissan – ............................................................................................ 6 Special Notes ................................................................................... 47 Connector Types ............................................................................... 49 Engine ............................................................................................... 51 Automatic Transmission ................................................................... 70 ABS ................................................................................................... 73 SRS – Airbag .................................................................................... 74 0 Vehicle Connection & Diagnostics Connecting the SCANNER to the Vehicle This section of the manual gives you drawings of the vehicle diagnostic connectors and tells you which SCANNER adapter to use. The carmakers are listed alphabetically for quick-reference. After you have identified the vehicle, the SCANNER display then tells you where to find the diagnostic connector and which vehicle adapter to use. Note on Functional Tests Functional tests are not applicable to Ethos software. Special Notes on Graph Mode Note that not all vehicle systems will be able to be displayed in the Graph Mode due to the communication type. It may also take several attempts to establish communication in Graph Mode. This is not a fault