Wiring Diagram 4 Now a Few Simple Steps Away from Enjoying Your New Car Radio with Radio Wire Reference Chart Enhanced Features

SELECT VEHICLE PRINT PAGES NEEDED

HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

2 Print only the pages for your vehicle using the advanced options in the Print menu.

3 Install your Maestro RR according to the guide for your vehicle.

WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certiﬁ ed technician. Logos and trademarks used here in are the properties of their respective owners. INSTALL GUIDE Ford Cmax WITH 4.3” MYFORD SCREEN 2013-2016 retains steering wheel controls, factory amplifier and more!

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. Ford Cmax with 4.3" screen 2013-2016

WELCOME DURING INSTALLATION

Congratulations on the purchase Installation Instructions 3 of your iDatalink Maestro RR Radio replacement solution. You are Wiring Diagram 4 now a few simple steps away from enjoying your new car radio with Radio Wire Reference Chart enhanced features. 5

Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct ﬁ rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer- ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 1 TROUBLESHOOTING TIPS: • To reset the module back its factory settings, turn the key • Unbox the aftermarket radio and locate its main harness. to the OFF position then disconnect all connectors from • Connect the wires shown on the next page from the module. Press and hold the module’s programming aftermarket radio main harness to the F02 T-harness and button and connect all the connectors back to the module. match the wire functions. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds). Release the programming button. STEP 2 Wait, the LED will turn solid GREEN for 2 seconds. • For technical assistance call 1-866-427-2999 or e-mail • Connect the factory harness to the F02 T-harness. “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” STEP 3 • Connect the screen harness to the F02 T-harness.

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 5 • Connect the 4 pin blue plug to the maestro and the other end to he aftermarket radio. For Kenwood and JVC use the BLUE/YELLOW wire, all other radios use the 3.5 jack. • Connect the auxiliary and backup camera RCA cables into the aftermarket radio (if equipped).

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) GREEN/BLACK - LR SPEAKER (-) PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND CONNECT TO RED - ACCESSORY (+) YELLOW - 12V (+) AFTERMARKET RADIO ORANGE - PARKING LIGHT (+) SEE PURPLE/WHITE - REVERSE LIGHT (+) AFTERMARKET LTGREEN - E-BRAKE (-) RADIO GUIDE RCA CABLES PINK - VEHICLE SPEED FOR WIRE YELLOW/BLACK - FOOT BRAKE COLORS CONNECT ONLY WHEN BROWN (NOT CONNECTED) THERE IS NO SYNC IN VEHICLE

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Automotive Data Solutions Inc. © 2017 ADS-RR(SR)-FOR02-AS maestro.idatalink.com 5 INSTALL GUIDE Ford Escape WITH 4.3” MYFORD SCREEN 2013-2015 retains steering wheel controls, factory amplifier and more!

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Automotive Data Solutions Inc. © 2017 ADS-RR(SR)-FOR02-AS maestro.idatalink.com 5 INSTALL GUIDE Ford Explorer WITH 4.3” MYFORD SCREEN 2011-2015 retains steering wheel controls, factory amplifier and more!

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Automotive Data Solutions Inc. © 2017 ADS-RR(SR)-FOR02-AS maestro.idatalink.com 5 INSTALL GUIDE Ford Focus WITH 4.3” MYFORD SCREEN 2012-2014 retains steering wheel controls, factory amplifier and more!

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Automotive Data Solutions Inc. © 2017 ADS-RR(SR)-FOR02-AS maestro.idatalink.com 5 INSTALL GUIDE Ford Taurus WITH 4.3” MYFORD SCREEN 2013-2014 retains steering wheel controls, factory amplifier and more!

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Automotive Data Solutions Inc. © 2017 ADS-RR(SR)-FOR02-AS maestro.idatalink.com 5 INSTALL GUIDE Ford Transit Connect WITH 4.3” MYFORD SCREEN 2014-2016 retains steering wheel controls, factory amplifier and more!

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

Automotive Data Solutions Inc. © 2017 ADS-RR(SR)-FOR02-AS maestro.idatalink.com 5 INSTALL GUIDE Ford Transit WITH 4.3” MYFORD SCREEN 2015-2016 retains steering wheel controls, factory amplifier and more!

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-AS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio.

STEP 6 • Connect all the harnesses to the Maestro RR module then proceed to module setup.

The module is now ready to be used. Insert the aftermarket radio in the dashboard housing and test all the functionalities. Reassemble the dashboard carefully.

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS STEERING WHEEL CONTROL CABLE

WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6

STEP 4 OBDII CONNECTOR A E

MAESTRO RR MODULE

G FO2 T-HARNESS A F E F C

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

2 Print only the pages for your vehicle using the advanced options in the Print menu.

3 Install your Maestro RR according to the guide for your vehicle.

WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 1 2013 Kenwood Radios: For these radio models, the OEM Bluetooth is turned OFF • Unbox the aftermarket radio and locate its main harness. by default. To turn ON the OEM Bluetooth, insert the key • Connect the wires shown on the next page from into the ignition and turn it to the ACC position. The Radio aftermarket radio main harness to the F02 T-harness and will turn on and the setup screen will appear. Scroll to the match the wire functions. bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select ON. Press the return arrow then scroll to the bottom of the page select STEP 2 FINISH. • Connect the factory harness to the F02 T-harness. 2014 Kenwood Radios: STEP 3 For these radio models, the OEM Bluetooth is turned ON by default. To turn OFF the OEM Bluetooth, insert the key • Connect the screen harness to the F02 T-harness. into the ignition and turn it to the ACC position. The radio will turn ON and the setup screen will appear. Scroll to the STEP 4 bottom and select the vehicle set up menu by pressing SET. Go to the option OEM Bluetooth and select OFF. • Plug the OBDII connector into the OBDII of the vehicle.

2014 Alpine Radios: STEP 5 For these radio models, the OEM Bluetooth is turned ON by • Plug the aftermarket radio harnesses into the aftermarket default. To turn OFF the OEM Bluetooth, insert the key into radio. the ignition and turn it to the ACC position. The radio will • Connect the auxiliary and backup camera RCA cables into turn ON and the main screen will appear. Select the settings the aftermarket radio (if equipped). button, in the top right corner, then select GENERAL. Select INTEGRATION SETUP then select HANDS FREE • Plug the Data cable to the data port of the aftermarket CONNECTION. Two options will be available ON or OFF, radio. select OFF. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio.

TROUBLESHOOTING TIPS: STEP 6 • To reset the module back its factory settings, turn the key • Connect all the harnesses to the Maestro RR module then to the OFF position then disconnect all connectors from proceed to module setup. the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may The module is now ready to be used. take up to 10 seconds). Release the programming button. Insert the aftermarket radio in the dashboard housing and Wait, the LED will turn solid GREEN for 2 seconds. test all the functionalities. • For technical assistance call 1-866-427-2999 or e-mail Reassemble the dashboard carefully. “[email protected]”. Visit us at “maestro.idatalink. com/support” and “www.12voltdata.com/forum/” OEM BLUETOOTH SETUP Only one Bluetooth can be set for hands free calling. This must be determined before installation. Both the factory and after systems can be used for bluetooth audio streaming. If the aftermarket Bluetooth is chosen for hands free calling, the aftermarket microphone must be installed in the vehicle

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - PARKING LIGHT (+) SEE RADIO PURPLE/WHITE - REVERSE LIGHT (+) WIRE REFERENCE LTGREEN - E-BRAKE (-) CHART FOR RCA CABLES PINK - VEHICLE SPEED RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS CONNECT ONLY WHEN BROWN (NOT CONNECTED) THERE IS NO SYNC IN VEHICLE

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

PRODUCTS REQUIRED OPTIONAL ACCESSORIES PROGRAMMED FIRMWARE iDatalink Maestro RR Radio Replacement Interface None ADS-RR(SR)-FOR02-DS iDatalink Maestro FO2 Installation Harness

WELCOME DURING INSTALLATION

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

WIRING DIAGRAM STEP 1

CUT AND REMOVE THE RCA JACKS STEP 5

AUX IN

BACKUP CAM

STEP 2 FACTORY RADIO HARNESS DATA AUDIO CABLE CABLE WIRES FROM VEHICLE

STEP 3 SCREEN HARNESS ABOVE RADIO

STEP 6 STEP 4 OBDII CONNECTOR A

H D

MAESTRO RR MODULE

C H G FO2 T-HARNESS A F

F C D

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Polarity Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable Description T-Harness

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

HOW TO USE THIS INSTALL GUIDE 1 Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

2 Print only the pages for your vehicle using the advanced options in the Print menu.

3 Install your Maestro RR according to the guide for your vehicle.

WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation.

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

PRODUCTS REQUIRED OPTIONAL ACCESSORIES iDatalink Maestro RR or RR2 Radio Replacement Interface Click here for: iDatalink Maestro FO1 Installation Harness Radar Installation Guides ELECTRONICS PROGRAMMED FIRMWARE ADS-RR(SR)-FOR01-DS

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Before starting your installation, Troubleshooting Table 6 please ensure that your iDatalink Maestro module is programmed with the correct ﬁ rmware for your vehicle and that you carefully review the install guide.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 1 • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio • Unbox the aftermarket radio and locate its main harness. input, connect to AUX). • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. Note: On Pioneer radio, ensure that there is nothing Connect every wire to the aftermarket radio main harness plugged into the W/R port. and match the wire colors. • Insert the RCA connectors into the aftermarket radio. • Connect every wire from the aftermarket radio main NOTES: harness to the FO1 T-harness and match the wire colors. (Refer to Diagram) The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory ampliﬁer. The RCA connector labeled CENTER IN can be used to STEP 2 feed the center channel of the THX system or as a second Vehicles equipped with navigation radios skip to Step 3. subwoofer channel (if applicable). (Required for vehicles equipped with SYNC, without factory The RCA connectors labeled AUX IN can be used to navigation system; refer to Vehicle Wire Chart) connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the • Disassemble the dashboard carefully and remove the aftermarket radio. factory radio from its housing without disconnecting it. • See the WIRE CHART for vehicle wire color and location. STEP 6 • Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test • Secure the aftermarket radio in the dashboardhousing. probe to the wire SWI 2 wire. Have the ignition and the • Connect all the harnesses to the Maestro RR module then radio ON. If the SWI 2 wire is connected, the multimeter test your installation. will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button. • Cut the SWI 2 INPUT wire. • Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER DASH, UNDER THE RADIO CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the vehicle. If you hardwired connections at the OBDII, check connections at the OBDII connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/ BROWN wire is connected to PIN 14 of the OBDII connector. Do not use T-Taps. Soldering or military splicing methods are recommended.

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The radio will not turn on, and there was no 16-pin plug connected to the The data lines are not present behind the radio and must be connected at the OEM radio. OBDII. Extend and connect the BROWN/RED and BROWN/YELLOW wires from the FO1’s 16-pin plug to: BROWN/RED to pin 3 (GRAY/ORANGE) and BROWN/YELLOW to pin 11 (VIOLET/ ORANGE) at the OBDII.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and that it is plugged into the black port on the Maestro RR. The red and blue ports on the RR should be empty.

Make sure the correct radio model and serial number were entered during the ﬂ ash. Verify the radio’s serial number entered during the ﬂ ash matches what is listed on the radio screen. This can be found in the settings of the radio, listed as Device Id, Device Number, or Serial Number.

MAESTRO RR RESET PROCEDURE:

Turn the key to the OFF position, then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will ﬂ ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest ﬁ rmware from the manufacturer. Please visit the radio manufacturer’s website and look for any updates pertaining to your radio.

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE JUNCTION CONNECTOR, BEHIND THE RADIO TO THE RIGHT CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : WHITE/BROWN CENTER CONSOLE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE PASSENGER SIDE, NEXT TO GLOVE BOX CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 1 STEP 5 • Unbox the aftermarket radio and locate its main harness. • Secure the aftermarket radio in the dashboardhousing. • Cut the WHITE, GRAY, GREEN and PURPLE RCA tips. • Connect all the harnesses to the Maestro RR module then Connect every wire to the aftermarket radio main harness test your installation. and match the wire colors. • Connect every wire from the aftermarket radio main harness to the FO1 T-harness and match the wire colors. (Refer to Diagram) • Remove the factory radio.

STEP 2 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 4 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX). Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. • Insert the RCA connectors into the aftermarket radio.

NOTES: The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory ampliﬁer. The RCA connector labeled CENTER IN can be used to feed the center channel of the THX system or as a second subwoofer channel (if applicable). The RCA connectors labeled AUX IN can be used to connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the aftermarket radio.

WIRING DIAGRAM STEP 1 STEP 4

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS BROWN (NOT CONNECTED) RCA CABLES

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEP 2 FACTORY RADIO HARNESS DATA CABLE

AUDIO CABLE

WIRES FROM VEHICLE

STEP 3 OBDII CONNECTOR

STEP 5

PINK/RED (NC) MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER DASH, UNDER THE TRAY CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 2 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

WIRING DIAGRAM STEP 1 STEP 4

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS BROWN (NOT CONNECTED) RCA CABLES

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEP 2 FACTORY RADIO HARNESS DATA CABLE

AUDIO CABLE

WIRES FROM VEHICLE

STEP 3 OBDII CONNECTOR

STEP 5

PINK/RED (NC) MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 2 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

WIRING DIAGRAM STEP 1 STEP 4

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS BROWN (NOT CONNECTED) RCA CABLES

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEP 2 FACTORY RADIO HARNESS DATA CABLE

AUDIO CABLE

WIRES FROM VEHICLE

STEP 3 OBDII CONNECTOR

STEP 5

PINK/RED (NC) MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, JUNCTION CONNECTOR, IN FRONT OF THE SHIFTER CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, HORIZONTAL HARNESS ON THE HEATER BOX CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, IN FRONT OF THE ARM REST CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE OR BLUE SYNC UNIT, BEHIND THE GLOVE BOX CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 1 Note: On Pioneer radio, ensure that there is nothing plugged into the W/R port. • Unbox the aftermarket radio and locate its main harness. • Insert the RCA connectors into the aftermarket radio. • Connect every wire from the aftermarket radio main NOTES: harness to the FO1 T-harness and match the wire colors. (Refer to Diagram) The RCA connectors labeled SUB IN can be used to feed the subwoofer channel of the factory ampliﬁer. The RCA connector labeled CENTER IN can be used to STEP 2 feed the center channel of the THX system or as a second Vehicles equipped with navigation radios skip to Step 3. subwoofer channel (if applicable). (Required for vehicles equipped with SYNC, without factory The RCA connectors labeled AUX IN can be used to navigation system; refer to Vehicle Wire Chart) connect the factory 3.5 mm audio jack, in vehicles that are NOT equipped with SYNC, to the auxiliary input of the • Disassemble the dashboard carefully and remove the aftermarket radio. factory radio from its housing without disconnecting it. • See the WIRE CHART for vehicle wire color and location. STEP 6 • Use a multimeter to test the SWI 2 wire. Connect the BLACK test probe to ground (-) and connect the RED test • Secure the aftermarket radio in the dashboardhousing. probe to the wire SWI 2 wire. Have the ignition and the • Connect all the harnesses to the Maestro RR module then radio ON. If the SWI 2 wire is connected, the multimeter test your installation. will display approximately 5 volts. This value will drop upon pressing the steering wheel voice, phone or OK button. • Cut the SWI 2 INPUT wire. • Connect the PINK/RED wire of FO1 T-harness to the SWI 2 INPUT wire going to the steering wheel. Insulate the wire side going to the SYNC module and plug the SYNC harness into the SYNC module.

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. • Insert the Audio cable into the iDatalink 3.5 mm audio jack of the aftermarket radio (if there is no iDatalink audio input, connect to AUX). 2

WIRING DIAGRAM STEP 1 STEP 5 RCA CABLES WHITE PIONEER RADIO: LF RCA INPUT WHITE/BLACK ENSURE THAT NOTHING GRAY IS PLUGGED IN W/R PORT. RF RCA INPUT GRAY/BLACK GREEN LR RCA INPUT GREEN/BLACK PURPLE RR RCA INPUT PURPLE/BLACK MAIN HARNESS CONNECT TO BLUE/WHITE - AMP. TURN ON (+) AFTERMARKET RADIO BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS

PINK/RED - SWI 2 (-) INPUT INSULATE WIRE STEERING SYNC DATA WHEEL SIDE MODULE SIDE CABLE AUDIO SWI 2 : BLUE/ORANGE OR BLUE CABLE SYNC UNIT, BEHIND THE GLOVE BOX CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE

STEP 6 STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS

STEP 3 FACTORY RADIO HARNESS WIRES FROM VEHICLE

STEP 6 STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : GRAY/BLUE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, HARNESS GOING TO THE BACK CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE SYNC UNIT, CENTER CONSOLE CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 2 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

WIRING DIAGRAM STEP 1 STEP 4

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS BROWN (NOT CONNECTED) RCA CABLES

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEP 2 FACTORY RADIO HARNESS DATA CABLE

AUDIO CABLE

WIRES FROM VEHICLE

STEP 3 OBDII CONNECTOR

STEP 5

PINK/RED (NC) MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 2 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

WIRING DIAGRAM STEP 1 STEP 4

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS BROWN (NOT CONNECTED) RCA CABLES

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEP 2 FACTORY RADIO HARNESS DATA CABLE

AUDIO CABLE

WIRES FROM VEHICLE

STEP 3 OBDII CONNECTOR

STEP 5

PINK/RED (NC) MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC STEP 2 SYNC HARNESS DATA PINK/RED - SWI 2 (-) INPUT INSULATE CABLE WIRE STEERING SYNC WHEEL SIDE MODULE SIDE AUDIO CABLE SWI 2 : BLUE/ORANGE CENTER CONSOLE, RIGHT SIDE, IN FRONT OF ARM REST CONNECTION REQUIRED ONLY IF EQUIPPED WITH SYNC

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 2 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 3 • Plug the OBDII connector into the OBDII of the vehicle.

WIRING DIAGRAM STEP 1 STEP 4

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS BROWN (NOT CONNECTED) RCA CABLES

SUB IN CENTER IN

AUX IN

CONNECT AUX IN ONLY IF YOU DON’T HAVE SYNC

STEP 2 FACTORY RADIO HARNESS DATA CABLE

AUDIO CABLE

WIRES FROM VEHICLE

STEP 3 OBDII CONNECTOR

STEP 5

PINK/RED (NC) MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/

RETAINS STEERING WHEEL CONTROLS, SYNC VOICE COMMANDS, SYNC BLUETOOTH AND MORE!

ADDITIONAL RESOURCES Maestro RR2 Programmable Outputs Guide

WELCOME TABLE OF CONTENTS

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

NEED HELP? 1 866 427-2999

[email protected]

maestro.idatalink.com/support www.12voltdata.com/forum

INSTALLATION INSTRUCTIONS

STEP 3 • Connect the factory harness to the FO1 T-harness. Connect only the available connectors. For example, if the factory harness has two connectors, connect only these two connectors.

STEP 4 • Plug the OBDII connector into the OBDII of the vehicle.

STEP 5 • Plug the aftermarket radio harnesses into the aftermarket radio. • Plug the Data cable to the data port of the aftermarket radio. 1

WIRING DIAGRAM STEP 1 STEP 5

CUT AND REMOVE PIONEER RADIO: ENSURE THAT NOTHING THE SPEAKER WIRE IS PLUGGED IN W/R PORT. JUNCTION CONNECTORS

WHITE - LF SPEAKER (+) WHITE/BLACK - LF SPEAKER (-) GRAY - RF SPEAKER (+) MAIN GRAY/BLACK - RF SPEAKER (-) HARNESS GREEN - LR SPEAKER (+) CONNECT TO GREEN/BLACK - LR SPEAKER (-) AFTERMARKET RADIO PURPLE - RR SPEAKER (+) PURPLE/BLACK - RR SPEAKER (-) BLUE/WHITE - AMP. TURN ON (+) BLACK - GROUND RED - ACCESSORY (+) YELLOW - 12V (+) ORANGE - ILLUMINATION (+) SEE RADIO WIRE PURPLE/WHITE - REVERSE LIGHT (+) REFERENCE LTGREEN - E-BRAKE (-) CHART PINK - VEHICLE SPEED FOR RADIO WIRE YELLOW/BLACK - FOOT BRAKE COLORS RCA CABLES BROWN (NOT CONNECTED)

SUB IN CENTER IN

AUX IN

STEP 3 FACTORY RADIO HARNESS

WIRES FROM VEHICLE

STEP 6

STEP 4 OBDII CONNECTOR

MAESTRO RR MODULE

FO1 T-HARNESS

NOT REQUIRED

STEERING WHEEL CONTROL CABLE

RADIO WIRE REFERENCE CHART

Wire Wire Color on Maestro Wire Color on Alpine Wire Color on Kenwood Wire Color on Pioneer Wire Color on Sony Polarity Description T-Harness cable cable cable cable

Illumination (+) Orange N/A Orange/White Orange/White Orange

Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

TROUBLESHOOTING TABLE

PROBLEM SOLUTION

Reset the RR. There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the RR and the radio. Make sure it is in the correct radio input.

The light on the Maestro is fl ashing RED ONCE. There is no fi rmware on the module; fl ash the RR module.

MAESTRO RR RESET PROCEDURE:

TECHNICAL ASSISTANCE Phone: 1-866-427-2999 Email: [email protected] Web: maestro.idatalink.com/support add www.12voltdata.com/forum/