ACP 131(B)

COMMUNICATION INSTRUCTIONS

OPERATING SIGNALS

ACP 131(B) r

This copy is a reprint which includes current pages from Changes 1 through 4 •

JULY 1964

r ORIGINAL (Reverse Blank) ACP 131(B) 10 July 1904

FOREWORD

1. ACP 131(B), COMMUNICATION INSTRUCTIONS-, is an Unclassified Publication. Periodic accounting is not required.

2. ACP 131(B) is effective upon receipt and supersedes ACP 131(A) which shall be destroyed by burning.

3. This publication contains allied military information and is furnished for official purposes only.

4. It is permitted to copy or make extracts from this publication.

Ill ORIGINAL (Reverse Blank) Change No. 5 to ACP 131(B) THE JOINT CHIEFS OF STAFF 28 APrj-l 1976 Washington, D.C 20301

UNITED STATES NATIONAL LETTER OF PROMULGATION FOR CHANGE NO. 5 TO ACP 131HT 1. The purpose of this National Letter of Promulgation is to implement Change No. 5 to ACP 131(B) within the Armed Forces of the United States. Change No. 5 to ACP 131(B), COMMUNICATION INSTRUCTIONS - OPERATING SIGNALS, was developed for allied use and, under the direction of the US Joint Chiefs of Staff, is promulgated for guidance, information, or use of the Armed Forces of the United States and other users of US military communications facilities. ^N 2. Change No. 5 to ACP 131(B) is an UNCLASSIFIED publication. 3. Change No. 5 to ACP 131(B) will be EFFECTIVE UPON RECEIPT for US use and is to be entered in the basic publication. After entry of Change No. 5 this National Letter of Promulgation shall be destroyed. * ' 4. This change will be made effective for allied use by separate means. Insert Change No. 5 pages but do not remove superseded pages. Insert following legend at bottom of superseded pages: "For NATO use only, remove this page when Change No. 5 is approved for NATO use." After entering Change No. 5 pages make the following notation at bottom of new pages: "For US use only. Delete ' this notation when Change No. 5 is approved for NATO use." 5. Correspondence concerning this publication should be addressed as f^\ follows: a. Service-originated correspondence will be forwarded through the normal military chain of command, marked for the attention of the appro priate Service communications chief or director, as listed below and will not be addressed to the Joint Chiefs of Staff: ' (1) Director, Telecommunications and Command and Control, US Army (2) Director, Naval Communications, US Navy (3) Director of Command Control and Communications, US Air Force b. Defense, national, and Federal agencies, as well as other recip ients of this publication, should address their correspondence to the /P^\ Chairman, Military Communications-Electronics Board, Washington, D.C. 20301.

For the Joint Chiefs of Staff:

J'^V. DAVID L.^ONES Colonel, USA Deputy Secretary f^ 3 of 3 CHANGE NO. 5 (Reverse Blank) ACP 131(B)

RECORD OF CHANGES AND CORRECTIONS

Enter Change or Correction in Appropriate Column

Identification of Change or Correction; Reg. No. (if any) By whom entered and date of same Date Entered (Signature; rank, grade or Change Correction rate; name of command)

j^N- VII ORIGINAL ACP 131(B)

RECORD OF CHANGES AND CORRECTIONS

Enter Change or Correction in Appropriate Column

Identification of Change or Correction; Reg. No. (if any) By whom entered and date of same Date Entered (Signature; rank, grade or rate; name of command) Change Correction

/^*%\ VIII ORIGINAL ACP 131(B)

COMMUNICATION INSTRUCTIONS OPERATING SIGNALS

TABLE OF CONTENTS

Section Paragraph Sub.ject Page Number

CHAPTER 1

GENERAL INSTRUCTIONS

101 Purpose , 1-1 102 General , 1-1 103 Authorization, 1-1 104 Instructions. 1-2

CHAPTER 2 OPERATING SIGNALS-DECODE

Q Signals 2A-1 QAA 2A-1 QBA 2A-4 QCA 2A-9 QDA 2A-11 QEA 2A-15 QFA 2A-17 QGA 2A-21 QHA 2A-23 QIA 2A-27 QJA 2A-29 OKA 2A-33 OLA 2A-35 QMA 2A-39 QNA 2A-41 QOA-QQZ.. 2A-44 QRA 2A-45 OJSA 2A-47 Q.TA 2A-51 QUA 2A-53 QVA-QZZ.. 2A-58

Z Signals 2B-1 ZAA 2B-1 ZBA 2B-3 ZCA 2B-7 ZDA 2B-9 ZEA 2B-13 ZFA 2B-15 ZGA 2B-19 ZHA 2B-21 ZIA 2B-25 ZJA 2B-27 ZKA 2B-31 ZLA 2B-33 ZMA 2B-37 ZNA 2B-39 ZOA 2B-43 ZPA 2B-45

IX CHANGE NO. 4 ACP 131(B) z^*^^

TABLE OF CONTENTS (Cont'd)

Section Paragraph Subject Page Number

CHAPTER 2 (Cont'd)

B (Cont'd) ZQA 2B-49 ZRA 2B-51 ZSA 2B-55 ZTA 2B-57 ZUA 2B-61 ZVA 2B-63 ZWA 2B-67 ZXA 2B-69

CHAPTER 3

OPERATING SIGNALS-ENCODE

Search and Rescue 3A-1 Navigation 3B-1 Direction Finding 3C-1 Aeronautical and Sea Operations 3D-1 Meteorology 3E-1 Communications Equipment and Circuits Adjusting and Testing 3F-1 Circuit Discipline and Net Control.... 3G-1 Message Handling 3H-1 Security and Cryptographic 31-1 Visual 3J-1 Exercise and Miscellaneous 3K-1

CHAPTER 4

MISCELLANEOUS ABBREVIATIONS AND SYMBOLS

4A-1 4B-1

CHAPTER 5

SERIES ZYA - ZZZ

(Reserved for intra-nation, Intra- service, or intra-command use)

ZYA. 5-1 ZZA. 5-3

CHAPTER 6

DESIGNATION OF EMISSIONS (Extract from Radio Regulations, Geneva, 1959)

Classification 6-1

CHANGE NO. 4 ACP 131(B)

CHAPTER 1

GENERAL INSTRUCTIONS

101. Purpose

The purpose of this publication is to list operating signals and provide jf^N instructions for their use. 102. General

This publication includes:

a. Operating Signals from the following series of international civil Q code:

(1) The series QAA to QNZ inclusive, the meanings of which are assigned by the International Civil Aviation Organization (ICAO). In general, the only civil stations that will have available a copy of this series are those of the Aeronautical Service. Therefore, this series is not to be used with other civil stations unless it is known that the station concerned is familiar with the series. (Note: Stations of the Aeronautical Service are those operated in accordance with ICAO inter national standards and recommended practices to provide for the safety of air navigation and for the regular, efficient and economical operation of the air services).

(2) The series QOA to QQZ inclusive is reserved for the Maritime ^\ Services. (3) The series QRA to QUZ inclusive, the meanings of which are assigned by the International Telecommunications Union (ITU). In general, all civil stations will have available a copy of this series. Therefore, this series may be used with all civil stations unless the station con cerned indicates its unfamiliarity with the series.

(4) The series QVA to QZZ inclusive has not been allocated to date.

b. Operating signals from the series ZAA to ZXZ inclusive of the allied military Z code. The series ZYA to ZZZ inclusive is reserved for the temporary or permanent assignment of meanings on an intra-military basis by any nation, service or command authorized use of this publication. For the convenience of assigning authorities, provision for this series (ZYA-ZZZ) is included in Chapter 5 of this publication.

c. Miscellaneous abbreviations and symbols developed or approved by ICAO for use with the series QAA to QNZ inclusive. These abbreviations and symbols, however, are authorized for use' by allied military stations with any Q or Z signal subject to the use limitations, if any, of that Q or Z signal (see ^\ paragraph 103). 103. Authorization

a. The series QAA to QUZ of the international civil Q code, and the series ZAA to ZXZ of the allied military Z code, are authorized for use between allied military stations subject to the provisions of paragraph 102. Q and Z signals of these series may be used together between allied military stations.

#^

1-1 CHANGE NO. 5 ACP 131(B)

103. (Continued)

b. The series QAA to QUZ of the international civil Q code are authorized for use between Allied military stations and civil stations, subject to the pro visions of paragraph 102. The allied military Z code (ZAA-ZZZ} is not authorized for use between allied military stations and civil commercial stations.

c. Any nation, service or command may prohibit or restrict the military | use, within its area of jurisdiction, of any operating signal. However, when ' such operating signals are received from other users, they must be recognized and acted upon.

104. Instructions

a. Action. Q or Z signals ordering or indicating that an action is to be taken (a change of frequency, for example) will be answered before the action is taken, unless the "Broadcast" method is used or the station ordering or indica ting the action has indicated that an answer is not required. b. Affirmatives or Negatives. Operating signals, as appropriate, will be used by allied military stations to convey an affirmative or negative sense... (1) To civil stations by adding "C" (affirmative) or "N" (negative) after the Q signal and any data used with it: Examples (of replies): (a) QFQ C means: (Yes) The approach and runway lights are lit. (b) QAK N means: (No) There is no risk of collision. "NO", in stead of "N", is authorized for use by and to civil stations of the Aeronautical Service. (2) To allied military stations by using the appropriate Q or Z signal: Examples (of replies): (a) QHZ means: (Yes) Circle the aerodrome (or go around). (b) ZOE means: (Yes) Give me your message. I will dispose of it. Note: In addition to the above, replies to questions from military stations may be made by using ZUE meaning Affirmative (Yes) or ZUG meaning Negative (No).

c. Blank Spaces. Blank spaces in the meanings of Q and Z signals will be completed, in the order in which they appear; however, blank spaces inclosed in parentheses normally will be completed on an optional basis only.

Examples: (1) QBM BF6 1010Z means: Here is the message sent by BF6 at 1010Z hours. Note: The meaning assigned QBM is "Here is the message sent by...at...hours"; therefore, as these blank spaces are not included in parentheses, all are completed, in the order in which they appear. (2) ZKO BG2 means: I have handed over guard to BG2. Note: The meaning assigned ZKO is "I have handed over guard (to...) (on...kHz (or MH2i)) (serial number of last message received was...)"; .however, in the above example, the user elected to complete only one of the blank spaces inclosed in parentheses. ^ x_2 CHANGE NO. 5 ACP 131(B)

104. (Continued) d. Call Signs. Normally call signs will follow the Q or Z signal to which they refer; however, they also may precede the operating signal for separation or clarity.

e. Frequencies: (1) When the meaning of a 0. or Z signal includes the expression "on... kHz (or MHz)", the figures used alone (not supplemented by an abbreviation) always will indicate the frequency in kilohertz per second. To indicate the frequency in megahertz per second, the figures will be supplemented by the abbreviation "MHz". (2) Provided that no confusion can arise, in those Q or Z signals whose meaning includes the expression "on...kHz (or MHz)", the circuit designator or other disguised reference, if available, will be used in place of the actual frequency. (3) Although not provided for in the meaning of a Q or Z signal, a frequency may be used with any such operating signal by adding figures . and the appropriate abbreviation ("kHz" (kilohertz per second) or "MHz" (megahertz per second)). f. Numbered Alternates. Q and Z signals with numbered alternate meanings will be followed, without spacing, by the appropriate number to indicate the meaning intended.

Examples: (1) QCB2 means: Delay is being caused by your slowness in answering. Note: QCB has the following numbered alternate meanings - "Delay is being caused by...(l. your transmitting out of turn; 2. your slowness in answer ing; 3. lack of your reply to my...)." (2) ZAP5 means: Work single sideband. Note: ZAP has the following numbered alternate meanings - "Work..,(l. simplex; 2. duplex; 3. diplex; 4. multiplex; 5. single sideband)." g. Plain Language. Plain unabbreviated language is authorized for use to complete or amplify the meaning of operating signals only when no other approved method will do. h. Questions. Operating signals, as appropriate, will be used by allied military stations to ask questions: (1) Of civil stations, by adding the prosign IM1 after the Q signal and any data used with it; Example: QAR 15 IMI means: May I stop listening on the watch frequency for 15 minutes? (2) Of military stations, by inserting the prosign INT before the Q or Z signal to which it refers.

Examples: (a) INT QAR 15 means: May I stop listening on the watch frequency for 15 minutes? (b) INT ZDJ means: How many groups does your message contain? f^' 1-3 CHANGE NO. 1 ACP 131(B)

104. (Continued) i. Security. Operating signals possess no security. They must be re garded as the equivalent of plain language. j. Separation. The separative sign (prosign II, written as a short dash) may be used to separate Q or Z signals when desired. k. Time Groups. Time groups (including date-time groups) used with Q or Z signals always will be followed, without spacing, by a zone suffix letter (see ACP 121), Although not provided for in the meaning of a Q or Z signal a time group (including date-time group) may be used with any such ' operating signal;

1. Units of Measurement. When units of measurement are desired for use which differ from those in the meaning of an operating signal, an appropriate abbreviation will be used (see Chapter 4). m. Class of Emission (Chapter 6). When using operating signals concern ing radio equipment or its use, e.g. QSU, QSW, ZTD, ZTE, ZTJ, ZTM, the class of emission/type of transmission may be indicated by use of the tables in Chapter 6. The operating signal ZTG is used for this purpose unless Chapter 6 is re ferred to in the meaning of the signal.

Examples: (1) QSU Fl means: Send or reply on this frequency use frequency shift keyed . (2) ZTM ZTG A3A means: I am unable to use single sideband, reduced carrier, telephony. /-^%

1-4 CHANGE NO. 1