DOCSLIB.ORG

EN 302 617 V1.1.1 (2008-01) European Standard (Telecommunications Series)

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
EN 302 617 V1.1.1 (2008-01) European Standard (Telecommunications Series) Draft ETSI EN 302 617 V1.1.1 (2008-01) European Standard (Telecommunications series) Electromagnetic compatibility and Radio spectrum Matters (ERM); Ground-based UHF radio transmitters, receivers and transceivers for the UHF aeronautical mobile service using amplitude modulation; Part 1: Technical characteristics and methods of measurement 2 Draft ETSI EN 302 617 V1.1.1 (2008-01) Reference DEN/ERM-TG25-262-1 Keywords aeronautical, AM, DSB, radio, testing, UHF ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88 Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. © European Telecommunications Standards Institute 2008. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI 3 Draft ETSI EN 302 617 V1.1.1 (2008-01) Contents Intellectual Property Rights................................................................................................................................7 Foreword.............................................................................................................................................................7 Introduction ........................................................................................................................................................7 1 Scope ........................................................................................................................................................8 2 References ................................................................................................................................................8 2.1 Normative references .........................................................................................................................................8 2.2 Informative references........................................................................................................................................8 3 Definitions and abbreviations...................................................................................................................9 3.1 Definitions..........................................................................................................................................................9 3.2 Abbreviations .....................................................................................................................................................9 4 General requirements ...............................................................................................................................9 4.1 Controls and indicators.......................................................................................................................................9 4.2 Class of emission and modulation characteristics ............................................................................................10 4.3 Warm up...........................................................................................................................................................10 5 Test conditions, power sources and ambient temperatures ....................................................................10 5.1 Normal and extreme test conditions .................................................................................................................10 5.2 Test power source.............................................................................................................................................10 5.3 Normal test conditions......................................................................................................................................10 5.3.1 Normal temperature and humidity..............................................................................................................10 5.3.2 Normal power sources ................................................................................................................................10 5.3.2.1 Mains voltage and frequency ................................................................................................................10 5.3.2.2 Other power sources..............................................................................................................................11 5.4 Extreme test conditions ....................................................................................................................................11 5.4.1 Extreme temperatures .................................................................................................................................11 5.4.2 Extreme values of test power sources.........................................................................................................11 5.4.2.1 Mains voltage........................................................................................................................................11 5.4.2.2 Other power sources..............................................................................................................................11 5.5 Performance test...............................................................................................................................................11 5.6 Environmental tests ..........................................................................................................................................12 5.6.1 General........................................................................................................................................................12 5.6.2 Procedure for tests at extreme temperatures ...............................................................................................12 5.6.3 Temperature tests........................................................................................................................................12 5.6.3.1 High temperature...................................................................................................................................12 5.6.3.2 Low temperature ...................................................................................................................................12 6 General conditions of measurement.......................................................................................................13 6.1 Receiver test signal arrangement......................................................................................................................13 6.1.1 Test signal sources......................................................................................................................................13 6.1.2 Nominal frequency .....................................................................................................................................13 6.1.3 Normal test signal .......................................................................................................................................13 6.1.4 Squelch .......................................................................................................................................................13 6.1.5 Normal audio output power ........................................................................................................................13 6.1.6 Audio AGC.................................................................................................................................................13 6.2 Transmitter test signal arrangement .................................................................................................................13 6.2.1 Coaxial termination.....................................................................................................................................13 6.2.2 Signal sources .............................................................................................................................................13 6.2.3 Normal test signal .......................................................................................................................................13 6.3 Test channels....................................................................................................................................................14
Load more

Recommended publications
  • RANDOM VIBRATION—AN OVERVIEW by Barry Controls, Hopkinton, MA
    RANDOM VIBRATION—AN OVERVIEW by Barry Controls, Hopkinton, MA ABSTRACT Random vibration is becoming increasingly recognized as the most realistic method of simulating the dynamic environment of military applications. Whereas the use of random vibration specifications was previously limited to particular missile applications, its use has been extended to areas in which sinusoidal vibration has historically predominated, including propeller driven aircraft and even moderate shipboard environments. These changes have evolved from the growing awareness that random motion is the rule, rather than the exception, and from advances in electronics which improve our ability to measure and duplicate complex dynamic environments. The purpose of this article is to present some fundamental concepts of random vibration which should be understood when designing a structure or an isolation system. INTRODUCTION Random vibration is somewhat of a misnomer. If the generally accepted meaning of the term "random" were applicable, it would not be possible to analyze a system subjected to "random" vibration. Furthermore, if this term were considered in the context of having no specific pattern (i.e., haphazard), it would not be possible to define a vibration environment, for the environment would vary in a totally unpredictable manner. Fortunately, this is not the case. The majority of random processes fall in a special category termed stationary. This means that the parameters by which random vibration is characterized do not change significantly when analyzed statistically over a given period of time - the RMS amplitude is constant with time. For instance, the vibration generated by a particular event, say, a missile launch, will be statistically similar whether the event is measured today or six months from today.
    [Show full text]
  • Amplifier Frequency Response
    EE105 – Fall 2015 Microelectronic Devices and Circuits Prof. Ming C. Wu [email protected] 511 Sutardja Dai Hall (SDH) 2-1 Amplifier Gain vO Voltage Gain: Av = vI iO Current Gain: Ai = iI load power vOiO Power Gain: Ap = = input power vIiI Note: Ap = Av Ai Note: Av and Ai can be positive, negative, or even complex numbers. Nagative gain means the output is 180° out of phase with input. However, power gain should always be a positive number. Gain is usually expressed in Decibel (dB): 2 Av (dB) =10log Av = 20log Av 2 Ai (dB) =10log Ai = 20log Ai Ap (dB) =10log Ap 2-2 1 Amplifier Power Supply and Dissipation • Circuit needs dc power supplies (e.g., battery) to function. • Typical power supplies are designated VCC (more positive voltage supply) and -VEE (more negative supply). • Total dc power dissipation of the amplifier Pdc = VCC ICC +VEE IEE • Power balance equation Pdc + PI = PL + Pdissipated PI : power drawn from signal source PL : power delivered to the load (useful power) Pdissipated : power dissipated in the amplifier circuit (not counting load) P • Amplifier power efficiency η = L Pdc Power efficiency is important for "power amplifiers" such as output amplifiers for speakers or wireless transmitters. 2-3 Amplifier Saturation • Amplifier transfer characteristics is linear only over a limited range of input and output voltages • Beyond linear range, the output voltage (or current) waveforms saturates, resulting in distortions – Lose fidelity in stereo – Cause interference in wireless system 2-4 2 Symbol Convention iC (t) = IC +ic (t) iC (t) : total instantaneous current IC : dc current ic (t) : small signal current Usually ic (t) = Ic sinωt Please note case of the symbol: lowercase-uppercase: total current lowercase-lowercase: small signal ac component uppercase-uppercase: dc component uppercase-lowercase: amplitude of ac component Similarly for voltage expressions.
    [Show full text]
  • Additive Synthesis, Amplitude Modulation and Frequency Modulation
    Additive Synthesis, Amplitude Modulation and Frequency Modulation Prof Eduardo R Miranda Varèse-Gastprofessor [email protected] Electronic Music Studio TU Berlin Institute of Communications Research http://www.kgw.tu-berlin.de/ Topics: Additive Synthesis Amplitude Modulation (and Ring Modulation) Frequency Modulation Additive Synthesis • The technique assumes that any periodic waveform can be modelled as a sum sinusoids at various amplitude envelopes and time-varying frequencies. • Works by summing up individually generated sinusoids in order to form a specific sound. Additive Synthesis eg21 Additive Synthesis eg24 • A very powerful and flexible technique. • But it is difficult to control manually and is computationally expensive. • Musical timbres: composed of dozens of time-varying partials. • It requires dozens of oscillators, noise generators and envelopes to obtain convincing simulations of acoustic sounds. • The specification and control of the parameter values for these components are difficult and time consuming. • Alternative approach: tools to obtain the synthesis parameters automatically from the analysis of the spectrum of sampled sounds. Amplitude Modulation • Modulation occurs when some aspect of an audio signal (carrier) varies according to the behaviour of another signal (modulator). • AM = when a modulator drives the amplitude of a carrier. • Simple AM: uses only 2 sinewave oscillators. eg23 • Complex AM: may involve more than 2 signals; or signals other than sinewaves may be employed as carriers and/or modulators. • Two types of AM: a) Classic AM b) Ring Modulation Classic AM • The output from the modulator is added to an offset amplitude value. • If there is no modulation, then the amplitude of the carrier will be equal to the offset.
    [Show full text]
  • Frequency Response and Bode Plots
    1 Frequency Response and Bode Plots 1.1 Preliminaries The steady-state sinusoidal frequency-response of a circuit is described by the phasor transfer function Hj( ) . A Bode plot is a graph of the magnitude (in dB) or phase of the transfer function versus frequency. Of course we can easily program the transfer function into a computer to make such plots, and for very complicated transfer functions this may be our only recourse. But in many cases the key features of the plot can be quickly sketched by hand using some simple rules that identify the impact of the poles and zeroes in shaping the frequency response. The advantage of this approach is the insight it provides on how the circuit elements influence the frequency response. This is especially important in the design of frequency-selective circuits. We will first consider how to generate Bode plots for simple poles, and then discuss how to handle the general second-order response. Before doing this, however, it may be helpful to review some properties of transfer functions, the decibel scale, and properties of the log function. Poles, Zeroes, and Stability The s-domain transfer function is always a rational polynomial function of the form Ns() smm as12 a s m asa Hs() K K mm12 10 (1.1) nn12 n Ds() s bsnn12 b s bsb 10 As we have seen already, the polynomials in the numerator and denominator are factored to find the poles and zeroes; these are the values of s that make the numerator or denominator zero. If we write the zeroes as zz123,, zetc., and similarly write the poles as pp123,, p , then Hs( ) can be written in factored form as ()()()s zsz sz Hs() K 12 m (1.2) ()()()s psp12 sp n 1 © Bob York 2009 2 Frequency Response and Bode Plots The pole and zero locations can be real or complex.
    [Show full text]
  • Evaluation of Audio Test Methods and Measurements for End-Of-Line Loudspeaker Quality Control
    Evaluation of audio test methods and measurements for end-of-line loudspeaker quality control Steve Temme1 and Viktor Dobos2 （1. Listen, Inc., Boston, MA, 02118, USA. [email protected]; 2. Harman/Becker Automotive Systems Kft., H-8000 Székesfehérvár, Hungary) ABSTRACT In order to minimize costly warranty repairs, loudspeaker OEMS impose tight specifications and a “total quality” requirement on their part suppliers. At the same time, they also require low prices. This makes it important for driver manufacturers and contract manufacturers to work with their OEM customers to define reasonable specifications and tolerances. They must understand both how the loudspeaker OEMS are testing as part of their incoming QC and also how to implement their own end-of-line measurements to ensure correlation between the two. Specifying and testing loudspeakers can be tricky since loudspeakers are inherently nonlinear, time-variant and effected by their working conditions & environment. This paper examines the loudspeaker characteristics that can be measured, and discusses common pitfalls and how to avoid them on a loudspeaker production line. Several different audio test methods and measurements for end-of- the-line speaker quality control are evaluated, and the most relevant ones identified. Speed, statistics, and full traceability are also discussed. Keywords: end of line loudspeaker testing, frequency response, distortion, Rub & Buzz, limits INTRODUCTION In order to guarantee quality while keeping testing fast and accurate, it is important for audio manufacturers to perform only those tests which will easily identify out-of-specification products, and omit those which do not provide additional information that directly pertains to the quality of the product or its likelihood of failure.
    [Show full text]
  • Calibration of Radio Receivers to Measure Broadband Interference
    NBSIR 73-335 CALIBRATION OF RADIO RECEIVERS TO MEASORE BROADBAND INTERFERENCE Ezra B. Larsen Electromagnetics Division Institute for Basic Standards National Bureau of Standards Boulder, Colorado 80302 September 1973 Final Report, Phase I Prepared for Calibration Coordination Group Army /Navy /Air Force NBSIR 73-335 CALIBRATION OF RADIO RECEIVERS TO MEASORE BROADBAND INTERFERENCE Ezra B. Larsen Electromagnetics Division Institute for Basic Standards National Bureau of Standards Boulder, Colorado 80302 September 1973 Final Report, Phase I Prepared for Calibration Coordination Group Army/Navy /Air Force u s. DEPARTMENT OF COMMERCE, Frederick B. Dent. Secretary NATIONAL BUREAU OF STANDARDS. Richard W Roberts Director V CONTENTS Page 1. BACKGROUND 2 2. INTRODUCTION 3 3. DEFINITIONS OF RECEIVER BANDWIDTH AND IMPULSE STRENGTH (Or Spectral Intensity) 5 3.1 Random noise bandwidth 5 3.2 Impulse bandwidth in terms of receiver response transient 7 3.3 Voltage-response bandwidth of receiver 8 3.4 Receiver bandwidths related to voltage- response bandwidth 9 3.5 Impulse strength in terms of random-noise bandwidth 10 3.6 Sum-and-dif ference correlation radiometer technique 10 3.7 Impulse strength in terms of Fourier trans- forms 11 3.8 Impulse strength in terms of rectangular DC pulses 12 3.9 Impulse strength and impulse bandwidth in terms of RF pulses 13 4. EXPERIMENTAL PROCEDURE AND DATA 16 4.1 Measurement of receiver input impedance and phase linearity 16 4.2 Calibration of receiver as a tuned RF volt- meter 20 4.3 Stepped- frequency measurements of receiver bandwidth 23 4.4 Calibration of receiver impulse bandwidth with a baseband pulse generator 37 iii CONTENTS [Continued) Page 4.5 Calibration o£ receiver impulse bandwidth with a pulsed-RF source 38 5.
    [Show full text]
  • Amplitude Modulation(AM)
    Introduction to Modulation: Amplitude Modulation(AM) Sharlene Katz James Flynn Overview Modulation Overview Basics of Amplitude Modulation (AM) AM Demonstration GRC Exercise 2 Flynn/Katz 7/8/10 Why do we need Modulation/Demodulation? Example: Radio transmission Voice Microphone Transmitter Electric signal, Antenna: 20 Hz – 20 Size requirement KHz > 1/10 wavelength c 3×108 Antenna too large! 5 Use modulation to At 3 KHz: λ = = 3 =10 =100km f 3×10 transfer ⇒ .1λ =10km information to a higher frequency 3 Flynn/Katz 7/8/10 Why do we need Modulation/Demodulation? (cont’d) Frequency Assignment Reduction of noise/interference Multiplexing Bandwidth limitations of equipment Frequency characteristics of antennas Atmospheric/cable properties 4 Flynn/Katz 7/8/10 Basic Concept of Modulation The information source Typically a low frequency signal Referred to as the “baseband signal” X(f) x(t) t f Carrier A higher frequency sinusoid baseband Modulated Modulator Example: cos(2π10000t) carrier signal Modulated Signal Some parameter of the carrier (amplitude, frequency, phase) is varied in accordance with the baseband signal 5 Flynn/Katz 7/8/10 Types of Modulation Analog Modulation Amplitude Modulation, AM Frequency Modulation, FM Double and Single Sideband, DSB and SSB Digital Modulation Phase Shift Keying: BPSK, QPSK, MSK Frequency Shift Keying, FSK Quadrature Amplitude Modulation, QAM 6 Flynn/Katz 7/8/10 Amplitude Modulation (AM) Block Diagram x(t) m x + xAM(t)=Ac [1+mx(t)]cos wct Ac cos wct Time Domain Signal information
    [Show full text]
  • Frequency Response Analysis
    Frequency Response Analysis Technical Report 10 tech10.pub 26 May 1999 22:05 page 1 Frequency Response Analysis Technical Report 10 N.D. Cogger BSc, PhD, MIOA R.V.Webb BTech, PhD, CEng, MIEE Solartron Instruments Solartron Instruments a division of Solartron Group Ltd Victoria Road, Farnborough Hampshire, GU14 7PW 1997 tech10.pub 26 May 1999 22:05 page 2 Solartron Solartron Overseas Sales Ltd Victoria Road, Farnborough Instruments Division Hampshire GU14 7PW England Block 5012 TECHplace II Tel: +44 (0)1252 376666 Ang Mo Kio Ave. 5, #04-11 Fax: +44 (0)1252 544981 Ang Mo Kio Industrial Park Fax: +44 (0)1252 547384 (Transducers) Singapore 2056 Republic of Singapore Solartron Transducers Tel: +65 482 3500 19408 Park Row, Suite 320 Fax: +65 482 4645 Houston, Texas, 77084 USA Tel: +1 281 398 7890 Solartron Fax: +1 281 398 7891 Beijing Liaison Office Room 327. Ya Mao Building Solartron No. 16 Bei Tu Chen Xi Road 964 Marcon Blvd, Suite 200 Beijing 100101, PR China 91882 MASSY, Cedex Tel: +86 10 2381199 ext 2327 France Fax: +86 10 2028617 Tel: +33 (0)1 69 53 63 53 Fax: +33 (0)1 60 13 37 06 Email: [email protected] Web: http://www.solartron.com For details of our agents in other countries, please contact our Farnborough, UK office. Solartron Instruments pursue a policy of continuous development and product improvement. The specification in this document may therefore be changed without notice. tech10.pub 26 May 1999 22:05 page 3 Frequency Response Analysis P E Wellstead B.Sc. M.Sc.
    [Show full text]
  • Federal Communications Commission § 73.1590
    Federal Communications Commission § 73.1590 the licensee must notify the FCC of the (2) FM stations. The total modulation date that normal operation was re- must not exceed 100 percent on peaks stored. If causes beyond the control of of frequent reoccurrence referenced to the licensee prevent restoration of the 75 kHz deviation. However, stations authorized power within 30 days, a re- providing subsidiary communications quest for Special Temporary Authority services using subcarriers under provi- (see § 73.1635) must be made to the FCC sions of § 73.319 concurrently with the in Washington, DC for additional time broadcasting of stereophonic or as may be necessary. monophonic programs may increase the peak modulation deviation as fol- [44 FR 58734, Oct. 11, 1979, as amended at 49 lows: FR 22093, May 25, 1984; 49 FR 29069, July 18, 1984; 49 FR 47610, Dec. 6, 1984; 50 FR 26568, (i) The total peak modulation may be June 27, 1985; 50 FR 40015, Oct. 1, 1985; 63 FR increased 0.5 percent for each 1.0 per- 33877, June 22, 1998; 65 FR 30004, May 10, 2000; cent subcarrier injection modulation. 67 FR 13232, Mar. 21, 2002] (ii) In no event may the modulation of the carrier exceed 110 percent (82.5 § 73.1570 Modulation levels: AM, FM, kHz peak deviation). TV and Class A TV aural. (3) TV and Class A TV stations. In no (a) The percentage of modulation is case shall the total modulation of the to be maintained at as high a level as aural carrier exceed 100% on peaks of is consistent with good quality of frequent recurrence, unless some other transmission and good broadcast serv- peak modulation level is specified in an ice, with maximum levels not to exceed instrument of authorization.
    [Show full text]
  • Nyquist Stability Criteria
    NPTEL >> Mechanical Engineering >> Modeling and Control of Dynamic electro-Mechanical System Module 2- Lecture 14 Nyquist Stability Criteria Dr. Bis ha kh Bhatt ac harya Professor, Department of Mechanical Engineering IIT Kanpur Joint Initiative of IITs and IISc - Funded by MHRD NPTEL >> Mechanical Engineering >> Modeling and Control of Dynamic electro-Mechanical System Module 2- Lecture 14 This Lecture Contains Introduction to Geometric Technique for Stability Analysis Frequency response of two second order systems Nyquist Criteria Gain and Phase Margin of a system Joint Initiative of IITs and IISc - Funded by MHRD NPTEL >> Mechanical Engineering >> Modeling and Control of Dynamic electro-Mechanical System Module 2- Lecture 14 Introduction In the last two lectures we have considered the evaluation of stability by mathema tica l eval uati on of th e ch aract eri sti c equati on. Rth’Routh’s tttest an d Kharitonov’s polynomials are used for this purpose. There are several geometric procedures to find out the stability of a system. These are based on: Nyquist Plot Root Locus Plot and Bode plot The advantage of these geometric techniques is that they not only help in checking the stability of a system, they also help in designing controller for the systems. Joint Initiative of IITs and IISc ‐ Funded by 3 MHRD NPTEL >> Mechanical Engineering >> Modeling and Control of Dynamic electro-Mechanical System Module 2- Lecture 14 NitNyquist Plo t is bdbased on Frequency Response of a TfTransfer FtiFunction. CidConsider two transfer functions as follows: s 5 s 5 T (s) ; T (s) 1 s2 3s 2 2 s2 s 2 The two functions have identical zero.
    [Show full text]
  • Licensed Devices General Technical Requirements
    Licensed Devices General Technical Requirements (Detailed Update October 2005) Steven Dayhoff Federal Communications Commission Office of Engineering & Technology October, 2005 ¾TCB Workshop 1 Sessions for licensed devices intended to give an overview of FCC Processes & Rules, not to show limits for every type of device. The information covered is mainly related to equipment authorization of the transmitting equipment and not the licensing of the station. 1 Overview General Information How to find information at the FCC Creating a Grant Organizing a Report Licensed Device Checklist October, 2005 ¾TCB Workshop 2 This session will cover general information related to the FCC rules and technical requirements for licensed devices. Assumption is that everyone is familiar with testing equipment so test setup and equipment settings will not covered. The approval process for these types of equipment was previously called Type Acceptance or Notification. Now all methods of equipment approval are called Certification. This information generally applies to all Radio Service Rules for scopes B1 through B4. 2 General Information Understanding how FCC rules for licensed equipment are written and how FCC operates The FCC rules are Title 47 of the Code of Federal Regulations Part 2 of the FCC Rules covers general regulations & Filing procedures which apply to all other rule parts Technical standards for licensed equipment are found in the various radio service rule parts (e.g. Part 22, Part 24, Part 25, Part 80, and Part 90, etc.) All material covered in this training is either in these rules or based on these rules October, 2005 ¾TCB Workshop 3 There are about 15 different radio service rule Parts which require equipment to be authorized before an operators license can be obtained.
    [Show full text]
  • Frequency Response of Amplifiers
    FREQUENCY RESPONSE OF AMPLIFIERS * Effects of capacitances within transistors and in amplifiers * Build on previous analysis of amplifiers from EENG 341 z Transistor DC biasing z Small signal amplification, i.e. voltage and current gain z Transistor small signal equivalent circuit * Use in Bipolar and FET Transistors Amplifiers and their analysis * Build on previous analysis of single time constant circuits z Review simple RC, LC and RLC circuits z Recall frequency dependent impedances for C and L z Review frequency dependence in transfer functions * Magnitude and phase * Examine origins of frequency dependence in amplifier gain z Identify capacitors and their origins; find the dominant C z Determine equivalent R and determine RC time constant z Use to describe approximately the amplifier’s frequency behavior z Examine effects of other capacitors * GOAL: Use results of analysis to modify circuit design to improve performance. 1 Analysis of Amplifier Performance * Previously analyzed z DC bias point z AC analysis (midband gain) * Neglected all capacitances in the transistor and circuit * Gain at middle frequencies, i.e. not too high or too low in frequency i B iC DC bias or quiescent point vBE vCE 2 Frequency Response of Amplifiers * In reality, all amplifiers have a limited range of frequencies of operation z Called the bandwidth of the amplifier z Falloff at low frequencies * At ~ 100 Hz to a few kHz * Due to coupling capacitors at the input or output, e.g. CC1 or CC2 z Falloff at high frequencies * At ~ 100’s MHz or few GHz 20 logT(ω) * Due to capacitances within the transistors themselves.
    [Show full text]