DOCSLIB.ORG

① Motorcyclists Should Wear Easy-To-Detect Clothing, Leather Gloves and Shoes, and Protective Gears

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
① Motorcyclists Should Wear Easy-To-Detect Clothing, Leather Gloves and Shoes, and Protective Gears (1) Which one of the following is incorrect regarding the characteristics of motorcycles? ① Motorcyclists should wear easy-to-detect clothing, leather gloves and shoes, and protective gears. ② Motorcycle brakes on the front and rear wheels are supposed to be applied at the same time. ③ Motorcyclists have greater maneuverability and wider field of vision than four-wheeled automobile drivers. ④ In general, motorcycles are better than four-wheeled automobiles in terms of instantaneous acceleration. ■ 정답: 2 (2) Which one of the following is correct regarding the characteristics of motorcycles? ① There is no blind spot that cannot be detected with rear-view mirrors. ② Motorcycles cannot apply engine brake when it is necessary to brake. ③ Motorcycles do not have to slow down to turn a curve. ④ A motorcycle tends to fall over when it slows down or stops. ■ 정답: 4 (3) Which one of the following is NOT a type of brake used in motorcycles? ① Front-wheel brake ② Rear-wheel brake ③ Exhaust brake ④ Engine brake ■ 정답: 3 (4) Which one of the following is incorrect advice on how a motorcycle should move on a curved road section? ① Before entering the curved section, decrease the speed according to the size of the curve. ② Look close ahead, and do not look around wide. ③ When you move along the curve, maintain a steady speed. ④ Make sure to balance the centrifugal force and gravity. ■ 정답: 2 (5) Which one of the following is the basic cornering technique where a motorcyclist leans inwards at the same angle as the motorcycle? ① Lean with ② Lean out ③ Lean brake ④ Lean in ■ 정답: 1 (6) Which one of the following is a cornering technique that motorcyclists can use on unpaved roads? ① Lean with ② Lean out ③ Lean brake ④ Lean in ■ 정답: 2 (7) Which one of the following is a cornering technique that motorcyclists use while riding at high speeds on paved roads? ① Lean with ② Lean out ③ Lean brake ④ Lean in ■ 정답: 4 (8) Which one of the following best explains the characteristics of motorcycle tires with round cross sections? ① They are designed to prolong the lifespan of the tire. ② They are designed for greater riding comfort. ③ They are designed to enhance fuel efficiency. ④ They are designed to maintain the centrifugal force and balance while negotiating a turn. ■ 정답: 4 (9) Which one of the following is NOT something the driver of a four-wheeled automobile must remember when they come across a motorcycle on the road? ① Remember that there could be optical illusions that lead you to believe that the motorcycle is going faster than it really is. ② Understand and remember that there is a risk that the motorcycle may be pulled underneath the car when turning right at an intersection. ③ Motorcycles are smaller than four-wheeled automobiles and are easily caught up in a blind spot. ④ While motorcycles and cars are easily in sight of each other, motorists tend to think that motorcycles are farther away than they really are due to their small size. ■ 정답: 1 (10) Which one of the following is NOT correct regarding a tandem motorcycle? ① Due to its increased weight, it accelerates faster and the centrifugal force becomes smaller. ② It is very important that the driver and the passenger work together to maintain balance. ③ Because it is very important for the driver and the passenger to work together to slow down, the passenger needs to be sufficiently informed. ④ The passenger should not ride when the road is slippery from snow or rain. ■ 정답: 1 (11) Which one of the following is incorrect about the characteristics of a moving motorcycle? ① Unlike the drivers of four-wheeled automobiles, motorcyclists tend to look at and around the lane to avoid speed bumps or stray rocks. ② Unlike the drivers of four-wheeled automobiles, motorcyclists are directly affected by the wind and find it difficult to control the handle. ③ When negotiating a curve, motorcyclists use the handle only to change direction. ④ When negotiating a curve, motorcyclists apply engine brake in advance to slow down. ■ 정답: 3 (12) Which one of the following is an incorrect method for a motorcyclist to drive? ① Shoulders: Relax the shoulders, and keep the back straight. ② Face: Pull your chin in, and your eyes should look ahead. ③ Feet: Place your feet on the foot pegs, with the toes facing the front and the soles of the feet parallel to the ground. ④ Knees: Spread both knees apart slightly around the fuel tank. ■ 정답: 4 (13) Which one of the following is NOT correct advice on the clothing of a motorcyclist? ① Wear light-colored clothing that protects the body and makes it easy to detect you. ② Wear leather gloves that allow you to move your fingers comfortably. ③ It is a good idea to attach reflectors for nighttime driving. ④ In the summer, wear sandals or other breathable shoes, and in the winter, wear long leather boots. ■ 정답: 4 (14) Which one of the following is NOT correct advice regarding the position of a moving motorcycle? ① Drive along the edge of the lane. ② Drive at the center of the lane. ③ Do not cut in between vehicles unreasonably. ④ Position yourself such that you are easily detected by other motorists. ■ 정답: 1 (15) Which one of the following is correct about distributing a motorcyclist’s attention along the field of vision and perspective? ① Look close ahead, and do not look wide. ② Look far ahead, and look wide. ③ Look far ahead, and do not look wide. ④ Look close ahead, and look wide. ■ 정답: 2 (16) Which one of the following is correct regarding a motorcyclist’s field of vision and perspective? ① The field of vision is wide left and right, and the horizon is set low. ② The field of vision is long up and down, and the horizon is set high. ③ The field of vision is narrow left and right, and the horizon is set high. ④ The field of vision is short up and down, and the horizon is set low. ■ 정답: 2 (17) Which one of the following is the most appropriate method for a motorcyclist to brake in order to balance and stop over a short distance? ① Use only the front-wheel brake. ② Use only the rear-wheel brake. ③ Use the front-wheel and rear-wheel brakes together. ④ Use only the front-wheel brake by applying the brake intermittently. ■ 정답: 3 (18) Which one of the following is incorrect about wearing a motorcycle safety helmet? ① A safety helmet protects your head and face in an accident. ② Fasten the buckle of the safety helmet slightly loosely under the chin. ③ A safety helmet absorbs and lessens shock. ④ Your safety helmet should not sit too much to the front or to the rear of your head. ■ 정답: 2 (19) Which one of the following is incorrect advice on selecting a motorcycle safety helmet that securely fits the driver? ① The helmet must be up to the prescribed standards. ② The helmet must have good visibility. ③ Select a helmet that satisfies your needs and purposes. ④ Select a helmet that is slightly bigger than your head. ■ 정답: 4 (20) Which one of the following is incorrect advice on selecting the visor for a motorcycle safety helmet? ① The visor must be in a dark tint in order to protect the driver’s eyes and vision from the sun. ② The visor must not distort the angle of the light. ③ The wearer must be able to tell the distance to other objects. ④ The visor must be made of safety glass to prevent injuries from shattered glass in case of an accident. ■ 정답: 1 (21) According to the Road Traffic Act, which one of the following is the correct weight for a motorcycle safety helmet? ① 1kg or less ② 1.5kg or less ③ 2kg or less ④ 2.5kg or less ■ 정답: 3 (22) According to the Road Traffic Act, which one of the following is incorrect advice on selecting a motorcycle safety helmet? ① It should come off easily on impact. ② It should absorb shock and be resistant to penetration. ③ It should allow for sufficient room for left/right and up/down view. ④ It should not inflict damage to human body. ■ 정답: 1 (23) Which one of the following is the most important thing to remember when a motorcycle changes direction or takes a turn? ① The location of your feet on the motorcycle foot pegs ② Controlling the brake system ③ Changing gear ④ Leaning of your body ■ 정답: 4 (24) Which one of the following correctly explains why a motorcycle should not drive over lane markings between vehicles? ① Because instantaneous acceleration could drop. ② Because it is difficult to ensure maneuverability. ③ Because it is difficult to balance the motorcycle body. ④ Because you can easily end up in a blind spot for four-wheeled vehicles. ■ 정답: 4 (25) When a motorcycle brakes suddenly on a curve, it may slip and fall easily due to ( ). Select the correct answer from below to fill in the blank ( ). ① Shock ② Centrifugal force ③ Moment of inertia ④ Friction ■ 정답: 2 (26) Which one of the following is correct regarding the distribution of force for enhanced braking when a motorcycle stops suddenly? ① The force is designed to be applied more to the front wheel. ② The force is designed to be applied more to the rear wheel. ③ The force is designed to be applied evenly to both wheels. ④ The force is designed not to be applied to either wheel. ■ 정답: 1 (27) Which one of the following is NOT an advantage motorcycles have over four-wheeled automobiles? ① Excellent maneuverability ② Wide view ③ Instantaneous acceleration ④ Higher shock absorption ■ 정답: 4 (28) Which one of the following is the best explanation why a motorcycle tire has a round cross section? ① To enhance the braking power.
Load more

Recommended publications
  • Some Equipment Innovations to Improve Safety of Highway Users and Maintenance Workers
    Some Equipment Innovations To Improve Safety of Highway Users and Maintenance Workers G. POINT Among the many Innovations developed in France in the field Driver-Controlled Applications of road maintenance, three in particular mny significantly im· prove users' and maintenance workers' safety: (a) the cone djs. • Cones can be placed at the required distance on either penser, whlch automatically and rapidly ets up and remove side of the vehicle. one or two rows of warning cones; (b) the mobile lane separator, • Cones, even overturned ones, can be collected from which can place road mnrkcr block that are imib1r to the New either side of the vehicle. Jersey type of barrier at either 12 or 30 km/ hr and (c) the • Cones can be picked up from one side and G810 road surface marking lorry for road sorfa line painting using several new technique that improve productivity a well simultaneously moved up to 3.5 m away on the other side. as personnel and t1:affic safety. These machines and their ad· • A traffic lane can be designated by setting down two vantages are discussed. lines of cones separated by a preprogrammed distance. Three kinds of equipment for road maintenance are discussed The standard cone dispenser only operates moving forward, in this paper. but an optional version is available for working in reverse. Recommended Vehicle CONE DISPENSER The recommended vehicle has a gross laden weight of 4.5 tonnes and a wheelbase of 3.2 m. With constantly growing volume of road traffic and the in· creasing number of maintenance operations, safety levels must Conclusion be increased.
    [Show full text]
  • Are Work Zones and Connected Automated Vehicles Ready for a Harmonious Coexistence? a Scoping Review and Research Agenda
    Dehman and Farooq 1 Are Work Zones and Connected Automated Vehicles Ready for a Harmonious Coexistence? A Scoping Review and Research Agenda Amjad Dehman, Ph.D., Senior Researcher* Laboratory of Innovations in Transportation (Litrans) Centre for Urban Innovation, Ryerson University 44 Gerrard Street East, Toronto ON M5G 1G3, Canada Emails: [email protected], [email protected] Phone: 416-979-5000 ext. 556456 Bilal Farooq, Ph.D., Associate Professor Laboratory of Innovations in Transportation (Litrans) Centre for Urban Innovation, Ryerson University 44 Gerrard Street East, Toronto ON M5G 1G3, Canada Emails: [email protected] Phone: 416-979-5000 ext. 556456 * Corresponding Author Abstract The recent advent of connected and automated vehicles (CAVs) is expected to transform the transportation system. CAV technologies are being developed rapidly and they are foreseen to penetrate the market at a rapid pace. On the other hand, work zones (WZs) have become common areas on highway systems as a result of the increasing construction and maintenance activities. The near future will therefore bring the coexistence of CAVs and WZs which makes their interaction inevitable. WZs expose all vehicles to a sudden and complex geometric change in the roadway environment, something that may challenge many of CAV navigation capabilities. WZs however also impose a space contraction resulting in adverse traffic impacts, something that legitimately calls for benefiting from the highly efficient CAV functions. CAVs should be able to reliably traverse WZ geometry and WZs should benefit from CAV intelligent functions. This paper reviews the state-of-the-art and the key concepts, opportunities, and challenges of deploying CAV systems at WZs.
    [Show full text]
  • Development of an Automated Visibility Analysis Framework for Pavement Markings Based on the Deep Learning Approach
    remote sensing Article Development of an Automated Visibility Analysis Framework for Pavement Markings Based on the Deep Learning Approach Kyubyung Kang 1 , Donghui Chen 2 , Cheng Peng 2, Dan Koo 1, Taewook Kang 3,* and Jonghoon Kim 4 1 Department of Engineering Technology, Indiana University-Purdue University Indianapolis (IUPUI), Indianapolis, IN 46038, USA; [email protected] (K.K.); [email protected] (D.K.) 2 Department of Computer and Information Science, Indiana University-Purdue University Indianapolis (IUPUI), Indianapolis, IN 46038, USA; [email protected] (D.C.); [email protected] (C.P.) 3 Korea Institute of Civil Engineering and Building Technology, Goyang-si 10223, Korea 4 Department of Construction Management, University of North Florida, Jacksonville, FL 32224, USA; [email protected] * Correspondence: [email protected]; Tel.: +82-10-3008-5143 Received: 29 September 2020; Accepted: 13 November 2020; Published: 23 November 2020 Abstract: Pavement markings play a critical role in reducing crashes and improving safety on public roads. As road pavements age, maintenance work for safety purposes becomes critical. However, inspecting all pavement markings at the right time is very challenging due to the lack of available human resources. This study was conducted to develop an automated condition analysis framework for pavement markings using machine learning technology. The proposed framework consists of three modules: a data processing module, a pavement marking detection module, and a visibility analysis module. The framework was validated through a case study of pavement markings training data sets in the U.S. It was found that the detection model of the framework was very precise, which means most of the identified pavement markings were correctly classified.
    [Show full text]
  • Assembly of Driving Schools, Thailand Translated from Thai Version of a Manual Book for Driver’S License Test Developed by Department of Land Transport
    Cover Manual book for driver’s license test The Land Traffic Act, B.E. 2522 (1979) Assembly of Driving Schools, Thailand Translated from Thai version of a manual book for driver’s license test developed by Department of Land Transport. Introduction Everyday road accident has caused many problems including life and property damages. Based on study, most of accidents were caused by people or having improper driving behaviors. Some of people do not understand traffic rules, drive with little caution, lack of driving skills, lack of awareness in driving with safety, and lack of disciplines to follow traffic rules. To increase knowledge related to traffic rules, regulations, skills in preventing from accidents and how to use road with safety, therefore, Department of Land Transport developed a manual related to “The Land Traffic Act, B.E. 2522 (1979) and The Motor Car Act, B. E. 2522 (1979). These two manuals aimed to disseminate knowledge about traffic rule, and correct use of motor car and road to interested people who wants to take a driving test. These manuals also help readers to understand traffic rule and drive better with quality and standard ways. Assembly of Driving Schools, Thailand April 2007 Content Introduction Manual book for driver’s license test The Land Traffic Act, B.E. 2522 (1979) . Definition . Use of vehicle . Use of vehicle’s light and horn . Loading . Traffic signals and signs . Driving or riding . Taking over other vehicle . Taking off, Taking turn, and Taking U-turn . Stopping and parking . Speed regulations . Driving pass intersection or roundabout . Emergency vehicle . Drawing and pulling .
    [Show full text]
  • Pavement Marking Technical Manual
    Pavement Marking Technical Manual This publication was produced by the Direction de l’encadrement et de l’expertise en exploitation and the Direction des matériaux d’infrastructures and edited by the Direction des normes et des documents d’ingénierie of the Ministère des Transports du Québec. The content of this publication is available on the Ministère’s website at the following address: www.transports.gouv.qc.ca. Cette publication est également disponible en français sous le titre “Manuel technique sur le marquage routier”. For more information, you can: • call 511 (in Québec) or 1 888 355-0511 (throughout North America) • consult the website of the Ministère des Transports: www.transports.gouv.qc.ca • write to the following address: Direction des communications Ministère des Transports 500, boulevard René-Lévesque Ouest, bureau 4.010 Montréal (Québec) H2Z 1W7 © Gouvernement du Québec, November 2019 ISBN 978-2-550-87234-4 (PDF) (Original edition: ISBN 978-2-550-85437-1 [PDF]) Legal deposit – 2020 Bibliothèque et Archives nationales du Québec All rights reserved for all countries. Reproduction by any means, and the translation, even in part, of this document are prohibited without the authorization of Publications du Québec. Acknowledgments The preparation of this publication was coordinated by Mélanie Beaulieu, eng., and Frédéric Boily, M. Sc., chemist. We wish to sincerely thank the following persons for their contribution: Johanne Chamberland, infographic designer, Direction des normes et des documents d’ingénierie Michaël Côté, graphic designer , Direction des normes et des documents d’ingénierie Gaétan Leclerc, M. Sc., chemist, Direction des matériaux d’infrastructures Audrée Perreault, eng., Direction de l’encadrement et de l’expertise en exploitation We also wish to thank everyone who took part, directly or indirectly, in preparing this document.
    [Show full text]
  • Review on Recent Traffic Signs in Lane Markings
    International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056 Volume: 05 Issue: 12 | Dec 2018 www.irjet.net p-ISSN: 2395-0072 Review on Recent Traffic signs in Lane Markings Ramesh Surisetty1, B.V. Suresh Kumar2 1Asst Prof, Dept of Civil Engineering, Coastal Institute of Technology &Management, Vizianagaram, India 2Asst Prof, Dept of Civil Engineering, Coastal Institute of Technology &Management, Vizianagaram, India ---------------------------------------------------------------------***---------------------------------------------------------------------- Abstract - India is a developing country and its cities are way into current civilization and advancements and new undergoing quick development and upgrading as a result innovations in the area are emerging more often. The there is high growth in the road traffic. Number of road users application of this technology in solving traffic related were dyeing every day because of road accidents. We need to problems like congestion is approximately has been done provide road surface marking is any kind of device or material and more research into it is going on. One of the ways the that is used on a road surface in order to take authorized technology is being applied is using it to provide traffic information. Lane detection is a process that is used to locate information through the Advanced Traveller Information the lane markers on the road, with the help of this lane System (ATIS) applications. markers presents these locations to an intelligent system. This system decreases the road accidents and also helps to Designing smarter automobiles, targeting to improves traffic conditions. minimize the number of motorist based wrong decisions or accidents, which can be faced with during the drive, is one of This study tested the effects of lane width, lane position and hot topics of today’s automotive technology.
    [Show full text]
  • Crowd-Sourced Mapping of New Feature Layer for High-Definition
    sensors Article Crowd-Sourced Mapping of New Feature Layer for High-Definition Map Chansoo Kim 1 ID , Sungjin Cho 1 ID , Myoungho Sunwoo 1 ID and Kichun Jo 2,* ID 1 Department of Automotive Engineering, Hanyang University, 222 Wangsimni-ro, Seongdong-gu, Seoul 04763, Korea; [email protected] (C.K.); [email protected] (S.C.); [email protected] (M.S.) 2 Department of Smart Vehicle Engineering, Konkuk University, Seoul 05029, Korea * Correspondence: [email protected]; Tel.: +82-2-2220-0453 Received: 8 October 2018; Accepted: 22 November 2018; Published: 28 November 2018 Abstract: A High-Definition map (HD map) is a precise and detailed map composed of various landmark feature layers. The HD map is a core technology that facilitates the essential functions of intelligent vehicles. Recently, it has come to be required for the HD map to continuously add new feature layers in order to increase the performances of intelligent vehicles in more complicated environments. However, it is difficult to generate a new feature layer for the HD map, because the conventional method of generating the HD map based on several professional mapping cars has high costs in terms of time and money due to the need to re-drive on all of the public roads. In order to reduce these costs, we propose a crowd-sourced mapping process of the new feature layer for the HD map. This process is composed of two steps. First, new features in the environments are acquired from multiple intelligent vehicles. The acquired new features build each new feature layer in each intelligent vehicle using the HD map-based GraphSLAM approach, and these new feature layers are conveyed to a map cloud through a mobile network system.
    [Show full text]
  • Evolution of Highway Failures and Their Maintenance
    INTERNATIONAL RESEARCH JOURNAL OF ENGINEERING AND TECHNOLOGY (IRJET) E-ISSN: 2395-0056 VOLUME: 07 ISSUE: 07 | JULY 2020 WWW.IRJET.NET P-ISSN: 2395-0072 EVOLUTION OF HIGHWAY FAILURES AND THEIR MAINTENANCE Golla Rama kishore1, K.Ramu2 M. Tech Scholar1, Asst Professor2, Department of Civil Engineering, A.M.REDDY Memorial College of Engineering and Technology, Narasaraopet (M),Guntur, Andhra Pradesh, India --------------------------------------------------------------------------***----------------------------------------------------------------------- ABSTRACT: A well-developed transportation infrastructure is essential for economic, industrial, social and cultural development of a country. Due to this need, human being has developed three modes of transport, i.e., by land, by water and by air. The road network has expanded from 4 lakh km in 1947 to 20 lakh km in 1993 and almost 55 lakh kms as on 31 March, 2015. India has less than 3.8 kms of road per 1000 people; including all its paved and unpaved roads. In terms of quality, all season, four or more lane highways; India has less than 0.07 kms of highway per 1000 people as of 2010. Inadequate maintenance of roads accounts to an act of disinvestment and sacrifice of past investment in roads. Roads have been receiving decreasing share of total Five Year Plan expenditure (decreasing from 6.7% in first plan to 3% in second plan). The Vehicle Operating Cost increases at a rapid rate as the condition of existing pavements starts deteriorating. The loss due to bad conditions of the main road network would be around Rs.12000 crore per annum. Pavement structure can be destroyed in a single season due to water penetration.
    [Show full text]
  • Semantic Classification of Road Markings from Geometric Primitives
    Semantic Classification of Road Markings from Geometric Primitives Paul Amayo, Tom Bruls, and Paul Newman Abstract— The classification of semantically meaningful road markings in images is an important and safety critical task for autonomous and semi-autonomous vehicles. However, beyond simple lane markings, real-time detection and interpretation of road markings is challenging as images are subject to occlusions, partial observations, lighting changes and differing weather conditions. Additionally, there is high variation in the road markings between countries and regions, which makes interpretation difficult. In this work we present a three-fold approach to the semantic classification. Firstly, we employ a weakly supervised neural network to detect pixels belonging to road markings under different conditions. Subsequently, these pixels are classified into geometric primitives, from which we retrieve the semantic classes through a fast and parallel model- fitting algorithm that offers real-time performance. Unlike other methods in the literature that perform road marking classifica- tion independently, our proposed approach performs a joint classification leveraging the highly structured configurations that characterise urban traffic scenes. Consequently, we retrieve the underlying semantic classes under a variety of weather and lighting conditions as we demonstrate in our results. Fig. 1. Semantic classification of road markings in an urban environment as I. INTRODUCTION implemented in this paper. From an image taken by the front-facing camera of an autonomous vehicle (top left), pixels of potential road markings can The safe operation and deployment of a robot is intrinsi- be identified by a trained deep neural network (top right) under various lighting conditions. A fast and real-time two-step global energy optimisation cally tied to its understanding of the work-space it operates approach then retrieves the road marking classes.
    [Show full text]
  • Evaluating All-Weather Pavement Markings in Illinois: Volume 1
    CIVIL ENGINEERING STUDIES Illinois Center for Transportation Series No. 15-018 UILU-ENG-2015-2024 ISSN: 0197-9191 EVALUATING ALL-WEATHER PAVEMENT MARKINGS IN ILLINOIS: VOLUME 1 Prepared By Neal Hawkins Omar Smadi Skylar Knickerbocker Center for Transportation Research and Education Iowa State University Adam Pike Paul Carlson Texas Transportation Institute Texas A&M University Research Report No. FHWA-ICT-15-018 A report of the findings of ICT-R27-120 Evaluating All-Weather Pavement Markings and Lab Methods to Simulate Field Exposure Illinois Center for Transportation December 2015 TECHNICAL REPORT DOCUMENTATION PAGE 1. Report No. 2. Government Accession No. 3. Recipient’s Catalog No. FHWA-ICT-15-018 4. Title and Subtitle 5. Report Date Evaluating All-Weather Pavement Markings in Illinois: Volume 1 December 2015 6. Performing Organization Code 7. Author(s) 8. Performing Organization Report Neal R. Hawkins, Adam M. Pike, Omar G. Smadi, Skylar Knickerbocker, and No. Paul J. Carlson ICT-15-018 UILU-ENG-2015-2024 9. Performing Organization Name and Address 10. Work Unit No. Center for Transportation Research and Education Iowa State University 11. Contract or Grant No. 2711 S. Loop Drive, Suite 4700 R27-120 Ames, IA 50010-8664 12. Sponsoring Agency Name and Address 13. Type of Report and Period Illinois Department of Transportation (SPR) Covered Bureau of Material and Physical Research 4/1/12 through 12/31/15 126 East Ash Street 14. Sponsoring Agency Code Springfield, IL 62704 FHWA 15. Supplementary Notes Conducted in cooperation with the U.S. Department of Transportation, Federal Highway Administration. 16. Abstract Pavement markings provide critical guidance to motorists, especially under dark (non-lighted) conditions.
    [Show full text]
  • Advanced Methods for Mobile Retroreflectivity Measurement on Paving Marking
    Advanced Methods for Mobile Retro-reflectivity Measurement on Pavement Marking Final Project Report Publication No. FHWA-17-CAI-001 January 2017 FORWARD • Purpose: This report provides an overview of the development of a mobile retroreflectivity unit for pavement marking measurement. • Content summary: This document details system capabilities and test results of a mobile data collection system for pavement marking. It describes an accurate, repeatable and reliable machine and methodology that will benefit transportation agencies and the motoring public they serve. • Interested audience: Pavement marking engineers, highway officials, municipality officials. • Previous printings of the publication: None • Publication status: FINAL Notice This document is disseminated under the sponsorship of the U.S. Department of Transportation in the interest of information exchange. The U.S. Government assumes no liability for the use of the information contained in this document. The U.S. Government does not endorse products or manufacturers. Trademarks or manufacturers' names appear in this report only because they are considered essential to the objective of the document. Quality Assurance Statement The Federal Highway Administration (FHWA) provides high-quality information to serve government, industry, and the public in a manner that promotes public understanding. Standards and policies are used to ensure and maximize the quality, objectivity, utility and integrity of its information. FHWA periodically reviews quality issues and adjusts its programs and processes to ensure continuous quality improvement. ii 1. Report No. 2. Government Accession No. 3. Recipient's Catalog No. 4. Title and Subtitle 5. Report Date Advanced Methods for Mobile Retro-reflectivity Measurement on December 2016 Pavement Marking Final Report 6.
    [Show full text]
  • Evaluation of the DELTA LTL-M Mobile Pavement Marking Retroreflectometer
    Evaluation of the DELTA LTL-M Mobile Pavement Marking Retroreflectometer Report prepared by Adam Pike, P.E. Associate Research Engineer College Station, Texas Report Prepared for DELTA April 2018 TABLE OF CONTENTS Page Disclaimer ...................................................................................................................................... ii Chapter 1: Work Plan .................................................................................................................. 3 Data Collection ........................................................................................................................... 3 Variables Evaluated ................................................................................................................ 3 Data Collection Procedures ..................................................................................................... 4 Open Road Testing ............................................................................................................. 4 Closed Course Testing ........................................................................................................ 6 Lab Testing ......................................................................................................................... 7 Chapter 2: Testing Results ........................................................................................................... 9 Open Road Testing Results ........................................................................................................
    [Show full text]