DOCSLIB.ORG

Inst-575 Parker Hale Bipod Adat

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Inst-575 Parker Hale Bipod Adat PARKER HALE BIPOD ADAPTER The Brownells Parker Hale Bipod Adapter allows the installation of a Parker Hale Bipod Spigot onto any rifle that has an Uncle Mike’s Sling Swiv- #080-000-005 el Stud located on the forearm. The PH Bipod Adapter is made from light- weight aluminum and can be quickly installed without making any perma- nent alterations to the rifle. The PH Bipod Adapter is also lined with a soft, U|xaFAIAGy10370mzV pigskin leather to help prevent marking or scuffing the rifle’s finish.The PH Bipod Adapter will also accept bipod spigots manufactured by Keng Firearms that markets the Versa Pod. ƽ WARNING ƽ Never attempt to disassemble or reassemble a firearm unless you are absolutely certain that it is empty and unloaded. Visually inspect the chamber, the magazine and firing mechanism to be absolutely certain that no ammunition remains in the firearm. Disassembly and re- assembly should follow the manufacturer’s instructions. If such in- READ & FOLLOW THESE structions are not immediately available, contact the manufacturer to see if they are available. If they are not available at all, then you should INSTRUCTIONS consult other reference sources such as reference books or persons with sufficient knowledge. If such alternative sources are not available and you have a need to disassemble or reassemble the firearm, you should proceed basing your procedures on common sense and experience with similarly constructed firearms. SELECTION. SERVICE. SATISFACTION.™ With regard to the use of these tools, the advice of Brownells Incor- 200 S. Front St. Montezuma, IA 50171 porated is general. If there is any question as to a specific application it 800-741-0015 or 641-623-4000 • www.brownells.com would be best to seek out specific advice from other sources and not sole- ly rely on the general advice and warnings given. HOW TO USE Secure the rifle, bottom side up in a padded bench vise. Place the rifle so you have unimpeded access to the forearm. This will make installation of the PH Bipod Adapter much easier and help prevent handling damage to the rifle. 5 Hold the PH Bipod Adapter in your hand and locate the ⁄32" Allen Head 5 Screw on the bottom of the PH Bipod Adapter. Use the ⁄32" Allen Wrench in- cluded in the kit to remove the screw and the flat washer.Carefully set these parts aside. Turn the PH Bipod Adapter over and the sling swivel stud cup should fall out of its recess located in the top (pigskin leather-faced side) of the PH Bipod Adapter. Remove the cross pin from the stud cup. Place the stud cup over the sling swivel stud located on the forearm of the rifle. Align the hole in the stud cup with the hole in the sling stud. Press the cross pin into the hole.The cross pin should insert easily into the hole in the sling stud. The stud cup is now retained on the sling stud. Place the PH Bipod Adapter over the top of the stud cup The spigot hole in the PH Bipod Adapter should be facing the muzzle end of the rifle. Align the through hole in the PH Bipod Adapter with the threaded hole in the bot- 5 SAVE THESE INSTRUCTIONS IN YOURtom of the stud cup. BROWNELLS GUNSMITHS DATA RING BINDER Reinstall the ⁄32" Allen Head screw and the flat wash- 5 er into the stud cup. Tighten the screw with the ⁄32" Allen Wrench included in the kit. Do not overtighten.The PH Bipod Adapter should now be securely held in place on the forearm. The leather-faced surface of the Adapter body should be in contact with the surface of the forearm. The radius of the Adapter body may not exactly match the radius of the forearm but the pigskin leather facing will help prevent marking of the rifle’s finish. Over- 5 tightening the ⁄32" Allen Head screw may cause damage to the rifle’s finish. The Parker Hale or Keng’s spigot can now be inserted into the spigot hole 3 located in the front of the PH Bipod Adapter. A ⁄32" Allen Head screw is lo- cated on the bottom of the Bipod Adapter body.This screw is tightened to re- 3 tain the spigot in the body of the adapter. Use the ⁄32" Allen Head wrench included with the kit. A #580 Uncle Mike’s QD Sling Swivel Stud and #20 black friction wash- er are also included in the kit.The additional sling swivel stud allows a sling to be used in conjunction with a bipod. The Sling Swivel Stud should be in- stalled in the 10-32 threaded hole located at the rear, bottom surface of the Adapter body. Place the black friction washer on the base of the sling swiv- el stud and thread the sling swivel stud into the 10-32 hole. Tighten until just snug. Do not overtighten. A drop of Blue Loctite™ can be used on the sling swivel stud prior to installation if desired. 076-200-575 Feb. 04r © 2004 BROWNELLS, INC. MADE IN U.S.A..
Load more

Recommended publications
  • Instruction for Vector Optics Tactical Bipod Mounts ATTENTION: Make Sure Firearm Is Unloaded Universal Picatinny Style
    Instruction for Vector Optics Tactical Bipod Mounts ATTENTION: Make sure firearm is unloaded Universal Picatinny Style Fit 21mm weaver and picatinny rail Press down the lockable button to open or folder the bipod Turn and release the leg sleeve, the spring loaded leg will be extended, then fasten the leg sleeve again To retract the leg, loosen the leg sleeve, push back the leg to the end, retighten the leg sleeve again Solid rubber feet avoid slipping With barrel mount adapter Stud Connection Style Stud connection mount for sling attachment Press the button to release the spring loaded leg If need to retract the extendable leg, just press the button again and push the leg back Solid rubber feet avoid slipping With weaver picatinny mount adapter. To use the adapter, remove the bipod tiny rubber sleeve, clamp into the adapter stud hole. Fasten the bottom nut. Swivel Stud Connection Style Swivel stud connection mount for sling swivel attachment Press the button to release the spring loaded leg 15 inch bipod, press first button and pull the extendable legs, press last button to release the spring loaded leg If need to retract the extendable leg, just press the button again and push the leg back Solid rubber feet avoid slipping Weaver picatinny mount adapter. To use the adapter, remove the bipod tiny rubber sleeve, clamp into the adapter stud hole. Fasten the bottom nut. Swing-able design for leveling on uneven ground. Select proper angle and fasten thumb nut to lock the position www.scvector.biz www.scvector.com .
    [Show full text]
  • Manson Precision Receiver Accurizing System
    Manson Precision Receiver Accurizing System Rhomboidal and pavid Slim reinterred her sundries feign or municipalizes estimably. Bewhiskered and dorsiventral Shurlock often disorientates some suspiration jeopardously or gumshoe therapeutically. Toothsome Ned sometimes climb-downs any hypogyny objectivize thriftily. Austenite molecular structure in receiver accurizing your order to impact forging die was attached to It has a receiver accurizing and precision machined hand when needed. National Match Rifle, Serial No. Ups For Remington Centerfire Rifles MAGAZINE CLIP is best carrying cases for extra ammo; they spoke right knowledge the gun. Available in precision manufacturing, deeply serrated face! Winchester receiver accurizing system and precision receiver, butt plate screw only received and the systems, the barrel bore. Sold had designed by the receiver accurizing kit! If they are precision. Even directional change the receiver accurizing system for precise, fulton armory operating rod rail hand and flexibility. The replacement magazine followers should have three neat and evenly spaced spot welds attaching the stop to the follower. End to match category will enlarge due to. The magazines were rotated for even use and the rate of fire was measured during one of the twenty round bursts. It is precision receiver accurizing system was unable to do so you wont need to work was a manson. He fled to the jungle the same day. SPECS: Aluminum, anodized, red. The reamer has a FLOATING pilot that measures approx. Bush and receiver. SPECS: Stainless steel, belt finish. Tactical Forums discussion board www. Low maintenance, Parkerized finish resists corrosion and matches the rest of your rifle. This corn is therefore excellent turnover and fluctuate barely ever used.
    [Show full text]
  • Art of Precision
    2017 CATALOGUE ART OF PRECISION «Promtechnologia» (Industrial Technology) company directs careful attention to its products’ quality which allows it to gain some impressive results: Orsis rifles’ accuracy exceeds their most common counterparts’ results greatly. This reality is confirmed by the multiple winning scores of shooters participating in high-accuracy shooting international competitions with their Orsis rifles in hands. There is a parameter in ballistics called “minute of angle” (or MOA) which estimates accuracy of shooting and it is defined, as a rule, by a group of 3-5 shots. Rifles having MOA ratio less than 1 are called sniper rifles. «Promtechnologia» company guarantees that all Orsis rifles demonstrate accuracy not over 0.5 MOA and a number of models demonstrate even better performance. www.orsis.com 3 President’s Message 4 Orsis Special 6 Orsis SE T-5000 M 8 Orsis M-15 Carbine 12 Orsis AR-10 National Match 16 Orsis Hunting 20 Orsis 120/140 22 Orsis SE Hunter M 26 Orsis SE Alpine M 30 Marocchi Si12 / Walnut 34 T-5000 / 8-11 120/140 / 22-25 Varmint / 48-51 Marocchi Si12 / Plastic 36 Marocchi First-E 40 Marocchi First-E Deluxe 42 Orsis Sport 46 Orsis Varmint M 48 Orsis F-Class 52 Glock Pistols 54 M-15 / 12-15 Hunter / 26-29 F-Class / 52-53 Production 56 High-Technology Equipment 58 High-Precision Technologies 59 Exceptional Materials 60 Innovative Development 61 International Cooperation 61 AR-10 / 16-19 Alpine / 30-33 Glock / 54-55 Services 62 Rifle Barrels Replacement 63 Cerakote Coating Application 63 Technical Maintenance 64 Decoration & Engraving 65 Orsis Сustom 65 Dealer Network 66 Marocchi / 34-45 Contacts 66 HIGH-PRECISION FIREARMS SYSTEMS ORSIS 4 ORSIS ART OF PRECISION President’s Message 5 Dear friends! The first catalogue of «Promtechnologia» (Industrial Technology) We support our shooters’ aspiration to be the best hunters and company is now introduced for your kind attention and, as you will sportsmen.
    [Show full text]
  • Summary Description Semi-Automatic Sporting Rifle SIG-AMT Cal
    - Summary Description Semi-Automatic Sporting Rifle SIG-AMT cal. 7.62x51 mm (.308 Win.) Swiss Industrial Company CH- 8212 Neuhausen Rhine Falls/Switzerland Phone 053/81555 Telex 76156 sig ch - 3 - Contents l. Weapon theory Page l.l. Designation and purpose 5 1.2. Main components and accessories 6- 7 1.3. Dismantling and assembly 9 1.4. Cleaning and maintenance ll 1.5. Functional checks 12 2. Manipulation 2.1. Loading, reloading, unloading 13-14 2.2. Positions of firing, using normal ammunition 14 2.3. Sight adjustments 16 3. Technical data 17-18 - 4 - - 5 - l. Weapon theory 1.1. Designation and purpose The semi-automatic sporting rifle SIG-AMT is a delayed blow-back weapon with stationary barrel and semi-rigid breech. The cartridges are fed from magazines of 5, 10 or 20 rounds. A considerably reduced recoil and the bipod which lends the rifle a firm support, improves accuracy of aim in all types of fire. Next to the normal trigger, in latched neutral position, is a winter trigger. This can be un­ latched and shifted into engagement to allow firing in mittens. In the head of the breech casing is a loading indicator, affording a visual check as to whe­ ther the weapon is loaded or unloaded. - 6 - - 7 - 1.2. Main components Accessories The principal parts of the weapon are: - Magazines for 5, 10 or 20 rounds - Barrel, bolted firmly to the breech casing. - Sling Pull-through with string and wire brush Breech casing with 2 lock heads, carrying - Loading indicator holder handle, loading indicator, bolt, rear sight and cartridge ejector opening.
    [Show full text]
  • CASV Handguard for the FAL Rifle Note: the CASV-FAL System Will Not Fit on Rifles Using the G1 Or Similarly Profiled Barrels
    CASV Handguard for the FAL Rifle Note: The CASV-FAL System will not fit on rifles using the G1 or similarly profiled barrels Improper installation can result in damage. Do not attempt installation if you are not familiar with the firearm, tools and techniques mentioned. You are responsible for any damage or READ injury resulting from the improper use THIS! or installation of this product. Ensure the rifle is CLEAR and SAFE! Before installation, read Instructions, Warnings and Notes. NOTE: Make sure that the firearm is unloaded and safe before proceeding – if you are unsure of how, or uncomfortable with the proper clearing and safe handling of the firearm, do not proceed! We recommend that the installation of this part be done only by a qualified gunsmith or agency armorer. 1. Before proceeding, please inspect the handguard assembly and hardware to ensure that you are familiar with all of the parts. 1 - Upper handguard Assembly 2 - Lower handguard Assembly 3 - Forward mounting screw retaining clip 4 - Forward mounting screw 5 - Rear mounting cross screw 6 - Rear mounting clamping nut 7 - Upper Handguard retaining screws (6 for FAS, 8 for FAL) 8 - Picatinny Accessory Rails & Screws 2. Install the lower handguard section by sliding it over the front sight gas block, and rearward over the handguard retainer. After the lower section is in place, install the forward mounting screw from the right side of the handguard, ensuring that it goes through the front sight gas block. Note: only snug the screw enough to hold the lower handguard section in place. 3.
    [Show full text]
  • PM Crew Served Weapons Overview Small Arms Symposium & Exhibition
    TheThe Soldier:Soldier: America’sAmerica’s MostMost DeployedDeployed CombatCombat SystemSystem PM Crew Served Weapons Overview for the Small Arms Symposium & Exhibition National Defense Industrial Association 16-19 May 2006 BG James R. Moran COL Carl A. Lipsit Mr. Peter Errante Program Executive Officer Soldier PM Soldier Weapons Deputy PM Crew Served Weapons Crew Served Weapons 2 PM Soldier Weapons Programs List DEVELOPMENT WEAPONS PROCUREMENT Objective Individual Combat Weapon (OICW) 37. M101, CROWS, Remote Mount 1. OICW Increment I 38. M151E1 & M151E2 Protector Remote Wpn System (RWS) 2. OICW Increment II - XM25 Air Burst Weapon 39. MK19 Advanced Crew Served Weapons (ACSW) 40. Mod Kit 3. Advanced Crew Served Weapon (ACSW) Programs 41. Lightweight Adjustable Sight Bracket 42. Tactical Engagement Simulator (TES) SOLDIER ENHANCEMENT PROGRAMS 43. M107 Semi Automatic Long Range Sniper Rifle 4. XM26 - 12 Gauge Modular Accessory Shotgun System 44. M240B, 7.62mm Medium MG (MASS) 45. M240B Collapsible Buttstock 5. Joint Combat Pistol 46. M192, Light Weight Ground Mount For MG 6. Family of Small Arms Suppressors 47. Improved Bipod 7. M68 Close Combat Optics (Dual Source Qualification) 48. Improved Flash Suppressor 8. XM1068, 12 Gauge Non-Lethal Extended Range Round 49. Combat Ammunition Pack 9. XM1022, Sniper Ammunition for M107 50. M240B Short Barrel 10. XM110 - 7.62 Semi-Automatic Sniper System (SASS) 51. M240B Improved Buttstock 11. Close Quarters Battle Kit 52. Sling Assembly for the M240B 12. XM1041/XM1042/XM1071 - Close Combat Mission 53. Short Barrel Capability Kit 54. M249, 5.56mm Squad Automatic Weapon 13. Advanced Sniper Accessory Kit (ASAK) 55. M192, Lightweight Ground Mount For MG 14.
    [Show full text]
  • Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology
    University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Anthropology Department Theses and Dissertations Anthropology, Department of 4-2013 Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology Eric T. Skov University of Nebraska-Lincoln, [email protected] Follow this and additional works at: https://digitalcommons.unl.edu/anthrotheses Part of the Anthropology Commons Skov, Eric T., "Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology" (2013). Anthropology Department Theses and Dissertations. 30. https://digitalcommons.unl.edu/anthrotheses/30 This Article is brought to you for free and open access by the Anthropology, Department of at DigitalCommons@University of Nebraska - Lincoln. It has been accepted for inclusion in Anthropology Department Theses and Dissertations by an authorized administrator of DigitalCommons@University of Nebraska - Lincoln. Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology by Eric Skov A THESIS Presented to the Faculty of The Graduate College at the University of Nebraska In Partial Fulfillment of Requirements For the Degree of Master of Arts Major: Anthropology Under the Supervision of Professor LuAnn Wandsnider Lincoln, Nebraska May, 2013 EXPERIMENTATION IN SLING WEAPONRY: EFFECTIVENESS OF AND ARCHAEOLOGICAL IMPLICATIONS FOR A WORLD- WIDE PRIMITIVE TECHNOLOGY Eric Thomas Skov, M.A. University of Nebraska, 2013 Adviser: LuAnn Wandsnider The sling is a simple, cheap and effective weapon that was widely distributed among prehistoric and historic populations. Well-known archaeological and textual evidence attests to its widespread military usage in Europe, South America and Central America. However, ethnographic and archaeological evidence also suggest that the sling was widely distributed among Native American populations.
    [Show full text]
  • USER MANUAL AR15 STYLE RIFLES Barnes Precision Machine A2-Style Muzzle Device
    INNOVATIVE REFINEMENTS TO THE TACTICAL CARBINE www.USAmade-AR15parts.com USER MANUAL AR15 STYLE RIFLES Barnes Precision Machine A2-Style muzzle device. Reduces muzzle blast and felt recoil, complete with breaching tip. MADE IN THE USA All Barnes Precision Machine rifles come standard with a stainless steel match grade barrel. Available in your choice of .223 Wylde or 5.56 NATO chambers and 11.5 to 18 inch lengths. Picatinny Spec Free-Float Rail System. Available in 7, 9, 12.5, and 14.5 inch lengths, featuring our patent pending enhanced barrel nut to achieve unprecedented rigidity for the length of the rail. Each rail system features four steel reinforced interchangeable sling swivel inserts. 7075 Forged Mil-spec CNC machined-hard anodized lower receiver with accurizing screw and detent set screw. Barnes Precision Machine © Copyright 2013 Patent Pending, All Rights Reserved Congratulations, you have purchased one of the finest rifles in the industry. Mil-spec machine tolerances. Manufactured on state of the art CNC machinery. Top quality materials-coating. All performed to ISO9001 standard. USA made craftsmanship and pride by skilled machinists in our North Carolina Facility. Innovative refinements to the tactical carbine OPERATING INSTRUCTIONS For safe operation instructions including Proper /Safe usage and /or maintenance, cleaning, repair, BPM Inc. recommends completion of a class by certified instructor (NRA/ NSSF, etc.) for training /operational understanding-proper, safe use of weapon system for tactical/personal defense/target/hunting as well as all other applications requiring basic understanding of said product(s) for SAFE /RELIABLE use/application of a LETHAL WEAPON. WARRANTY Due to the many different requirements imposed by federal and state laws on consumer warranties, no express warranty, either “full” or “limited” is offered with this product.
    [Show full text]
  • (12) United States Patent (10) Patent No.: US 7,121,034 B2 Keng (45) Date of Patent: Oct
    USOO7121034B2 (12) United States Patent (10) Patent No.: US 7,121,034 B2 Keng (45) Date of Patent: Oct. 17, 2006 (54) BPOD MOUNT AND GRIPASSEMBLY 6,487,807 B1 * 12/2002 Kopman et al. ............... 42.94 2005/0241206 A1* 11/2005 Teetzel et al. ................. 42.72 (76) Inventor: Da Keng, 875 Wharton Dr. S.W., Atlanta, GA (US) 30336 FOREIGN PATENT DOCUMENTS (*) Notice: Subject to any disclaimer, the term of this DE 103.108O2 A1 * 9, 2004 patent is extended or adjusted under 35 U.S.C. 154(b) by 0 days. * cited by examiner Primary Examiner J. Woodrow Eldred (21) Appl. No.: 11/056,134 (74) Attorney, Agent, or Firm Jones Tullar & Cooper, PC (22) Filed: Feb. 14, 2005 (57) ABSTRACT (65) Prior Publication Data A grip and bipod mounting device for mounting a bipod US 2005/O188588 A1 Sep. 1, 2005 Supporting grip assembly to a "picatinny’ mounting rail structure as are often affixed below the forearm stock of a Related U.S. Application Data firearm such as a military rifle (e.g., as per standard MIL STD-1913). In particular, the present invention is directed to (60) Provisional application No. 60/543,571, filed on Feb. mounting a Parker-Hale style of firearm bipod on a bipod 12, 2004. Supporting grip assembly including a contoured mounting (51) Int. C. block segment inletted to cover and attach to a picatinny rail affixed beneath the forearm stock of the firearm. A grip or F4 IC 23/00 (2006.01) handle depends transversely from the mounting block seg (52) U.S.
    [Show full text]
  • Universal Featherweight Bipod
    UNIVERSAL FEATHERWEIGHT BIPOD FitS: Any Firearm with a Sling Swivel Stud and AR-15 Types INSTALLATION INSTRUCTIONS PART# BIP0300 MAKE SURE YOUR FIREARM IS UNLOADED BEFORE STARTING! UNIVERSAL BIPOD ASSEMBLY: INSPECT EXISTING SLING SWIVEL STUD FOR TIGHTNESS! NON-SWIVEL SWIVEL Mounting O-Ring Bracket (Swivel Only) (See Step #9) Depress “Snap-n-Lock” button to fold Non-Swivel legs forward, OR IMPORTANT: Collar down or (See Step #10) Fits AR-15 with ROUND Mil Spec Yoke Assembly rearward Twist knurled knob Swivel Collar Handguards Without Modification. Halves to extend, retract M-4 Requires Additional Hole. or lock legs Fits any Rifle with Sling Swivel Stud OR Assemble Universal Bipod: Counterbore Washer Flat Top Washer 1. After deciding to build non-swivel or swivel bipod, position mounting bracket as shown in picture at right, install either the non-swivel collar or the swivel collar in the assembly. #10 x 3/4 Screws 2. Install non-swivel collar or swivel collar halves onto top side of mounting bracket with Thick Thick pins aligning with holes in mounting bracket. Washer Washer 3. If swivel collar halves were used, place o-ring into groove on top side of mounting bracket. Left Leg Right Leg 4. Install yoke assembly over post on mounting bracket and align (2) pins on bottom of yoke with holes in non-swivel collar or in open area between swivel collar halves. 5. Install washer over the post and secure with the pink pre-coated #10 x 3/4 screw using a Phillips screw driver. NOTE: Non-swivel Bipod will use the washer with the counterbore INSTALLING BIPOD TO RIFLE: top and Swivel Bipod will use the washer with the flat top.
    [Show full text]
  • Fabdefence.Pdf
    2012 2-15 grips 16-29 rail systems 30-33 K-pos 34-45 Buttstocks 46-53 TACTICAL FLASHLIGHT ADAPTORS 54-59 Magazine accessories 60-69 parts & upgrades 70-71 Self-Healing Targets 72 index gripsTarget Accuracy AG-43 AGF-43S AR15/M16 Pistol Grip Tactical Folding Pistol Grip for-M16-M4-AR15 Finger Swelts and a Backstrap Shape Designed to Enhance Transforms a Horizontal Positioned Grip to Vertical Position Grip, Even when Wet Weapon Fits Easier in Gun Case and on Weapon Rack Extended Beavertail for Better Control, Allowing a Higher Firmer Hold Provides Easier Maneuverability, more Convenient for Undercover Readily Accessible Storage Area with Securely Sealed Hinged Door Work and Concealment MIL-SPEC Reinforced Polymer Composite Easier and Faster Vehicular Deployment Available in Black and Two Camouflage Colors: Olive Drab Green and Desert Tan Quick Fold/Unfold Button Made From Reinforced Polymer Composite 04 Grips AG-47 AG-58 SG-1 Ergonomic Pistol Grip for AK-47/74 SA. VZ. 58 Pistol Grip Sniper Pistol Grip Advanced Ergonomic Design Prevents Unique Texture Prevents Slipping Replaces Standard Pistol Grip To Provide Wrist Fatigue and Ensures Secure Grip in When Wet Greater Comfort and Operational Control Wet Conditions Advanced Ergonomic Design Advanced Ergonomic Design Improves Trigger Operation Built-In Storage Compartment Adjustable Palm Swell Style Grip Built-In Storage with Removable Enhances Finger to Trigger Correspondence Adapts Easily To Various Sized Hands Cushioned Battery Holder Tough Material & Design Applies Pressure to the Palm of the Hand Manufactured with MIL-SPEC Reinforced Available in Black and Two Camouflage Allowing Deliberate and Measured Polymer Composite Colors: Olive Drab Green, and Desert Tan Trigger Pull Available in Black and Two Camouflage Tough Material & Design Colors: Olive Drab Green, and Desert Tan Available in Black 05 Grips agr-870 agm-500 wg-1911 Remington 870 Pistol Grip Mossberg 500 Pistol Grip 1911 Mag.
    [Show full text]
  • Product Catalog ® Company Overview Samson Manufacturing Is the Premier Manufacturer of Rearms Parts and Accessories
    ® ATM FOLDING STOCK for the Ruger® Mini-14® BTM FOLDING STOCK for the Ruger® 10/22™ Product Catalog ® Company Overview Samson Manufacturing is the premier manufacturer of rearms parts and accessories. Specializing primarily in the AR-15 market, Samson also has a diverse and accomplished product line including: Kalashnikov handguards, optics and magni er mounts, xed and folding ri e sights, and much, much more. Samson utilizes state of the art engineering and CNC machining techniques to ensure that all of our products not only exceed industry standards but set them. Located in Keene, NH and bringing to the table more than 24 years of design build experience, Samson Manufacturing is the only choice for retail customers, rearms manufacturers with specialized project needs, and distributors looking for excellent selection and extremely high cost/value. Samson serves retail customers and dealers directly and through a wide variety of distribution channels. OEM projects and custom design builds are handled directly by Samson’s product development team and we welcome the opportunity to prototype and produce custom, precision machined, CNC Scott W. Samson, President aluminum or plastic injection molded products to meet your company’s unique demands. Samson Manufacturing Samson is also heavily invested in the competition, Law Enforcement, and military Cathy Samson, President Samson International communities. We currently sponsor a professional shooting team with appearances on the 3 gun nation pro tour. Samson holds several U.S. military contracts with units in every branch of the armed forces as well as USSOCOM. Samson is also the supplier of the rear sights for the I.D.F.
    [Show full text]