DOCSLIB.ORG

Universal Featherweight Bipod

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Universal Featherweight Bipod UNIVERSAL FEATHERWEIGHT BIPOD FitS: Any Firearm with a Sling Swivel Stud and AR-15 Types INSTALLATION INSTRUCTIONS PART# BIP0300 MAKE SURE YOUR FIREARM IS UNLOADED BEFORE STARTING! UNIVERSAL BIPOD ASSEMBLY: INSPECT EXISTING SLING SWIVEL STUD FOR TIGHTNESS! NON-SWIVEL SWIVEL Mounting O-Ring Bracket (Swivel Only) (See Step #9) Depress “Snap-n-Lock” button to fold Non-Swivel legs forward, OR IMPORTANT: Collar down or (See Step #10) Fits AR-15 with ROUND Mil Spec Yoke Assembly rearward Twist knurled knob Swivel Collar Handguards Without Modification. Halves to extend, retract M-4 Requires Additional Hole. or lock legs Fits any Rifle with Sling Swivel Stud OR Assemble Universal Bipod: Counterbore Washer Flat Top Washer 1. After deciding to build non-swivel or swivel bipod, position mounting bracket as shown in picture at right, install either the non-swivel collar or the swivel collar in the assembly. #10 x 3/4 Screws 2. Install non-swivel collar or swivel collar halves onto top side of mounting bracket with Thick Thick pins aligning with holes in mounting bracket. Washer Washer 3. If swivel collar halves were used, place o-ring into groove on top side of mounting bracket. Left Leg Right Leg 4. Install yoke assembly over post on mounting bracket and align (2) pins on bottom of yoke with holes in non-swivel collar or in open area between swivel collar halves. 5. Install washer over the post and secure with the pink pre-coated #10 x 3/4 screw using a Phillips screw driver. NOTE: Non-swivel Bipod will use the washer with the counterbore INSTALLING BIPOD TO RIFLE: top and Swivel Bipod will use the washer with the flat top. 6. Install legs by inserting post on leg into hole on yoke. Position legs as shown in picture. AR-15 Lower FIG. 1 FIG. 2 7. Secure legs to yoke with thick washers and #10 x 3/4 screws using Phillips screw driver. Handguard Installing Bipod to Rifle: Standard For AR-15 Start at step #1 and Fig. 1; All Others Start at step # 3 and Fig. 2: 5/16” Sling Swivel Stock/Forend Retaining Stud 1. Remove lower handguard. Pin With Sling Mounting Swivel Stud 2. Insert the round threaded adapter through hole in lower handguard, align and install Column 5/16” sling swivel stud (See fig. 1). 3. Start #10-32 x 1/4 Allen Screw into top of the mounting column with supplied Allen Allen Screw wrench. 1/2” Sling Swivel 4. Place the mounting column over the front sling swivel stud. Align the through holes; Stud (Long) Allen Wrench then install and center the retaining pin. Tighten the Allen Screw. Install new 1/2” Neoprene threaded sling swivel stud and tighten. Pad 5. Remove backing from Neoprene Pad. Align and affix to bipod mounting bracket. 6. Align and install Bipod over the mounting column with legs parallel to the barrel and pointing toward muzzle. (Depress “Snap-N-Lock” button and rotate legs 180°.) Universal Featherweight 7. Place nylon washer over mounting column. Install mounting nut onto column and Bipod Assembled hand tighten plus 1/4 turn maximum. Failure to follow this procedure could result in Nylon damage to stock. Do Not OVertiGHten! Washer 8. Your Advanced Technology, Inc. Bipod is now in place and ready to use. Mounting Nut 9. To adjust legs forward, down, or rearward simply depress the “Snap-n-Lock” button and rotate leg to the desired location. Then release the button. 10. To adjust height (inner leg) twist knurled thumbscrew 1/4 turn and legs will freely drop. Knurled Knobs Retighten thumbscrew to lock in position. To retract legs simply invert rifle and repeat (Twist to Extend, Retract or process. Lock Legs) IS-BIP0300-062707.
Load more

Recommended publications
  • Instruction for Vector Optics Tactical Bipod Mounts ATTENTION: Make Sure Firearm Is Unloaded Universal Picatinny Style
    Instruction for Vector Optics Tactical Bipod Mounts ATTENTION: Make sure firearm is unloaded Universal Picatinny Style Fit 21mm weaver and picatinny rail Press down the lockable button to open or folder the bipod Turn and release the leg sleeve, the spring loaded leg will be extended, then fasten the leg sleeve again To retract the leg, loosen the leg sleeve, push back the leg to the end, retighten the leg sleeve again Solid rubber feet avoid slipping With barrel mount adapter Stud Connection Style Stud connection mount for sling attachment Press the button to release the spring loaded leg If need to retract the extendable leg, just press the button again and push the leg back Solid rubber feet avoid slipping With weaver picatinny mount adapter. To use the adapter, remove the bipod tiny rubber sleeve, clamp into the adapter stud hole. Fasten the bottom nut. Swivel Stud Connection Style Swivel stud connection mount for sling swivel attachment Press the button to release the spring loaded leg 15 inch bipod, press first button and pull the extendable legs, press last button to release the spring loaded leg If need to retract the extendable leg, just press the button again and push the leg back Solid rubber feet avoid slipping Weaver picatinny mount adapter. To use the adapter, remove the bipod tiny rubber sleeve, clamp into the adapter stud hole. Fasten the bottom nut. Swing-able design for leveling on uneven ground. Select proper angle and fasten thumb nut to lock the position www.scvector.biz www.scvector.com .
    [Show full text]
  • The European Bronze Age Sword……………………………………………….21
    48-JLS-0069 The Virtual Armory Interactive Qualifying Project Proposal Submitted to the Faculty of the WORCESTER POLYTECHNIC INSTITUTE in partial fulfillment of the requirements for graduation by _____________________________ ____________________________ Patrick Feeney Jennifer Baulier _____________________________ Ian Fite February 18th 2013 Professor Jeffrey L. Forgeng. Major Advisor Keywords: Higgins Armory, Arms and Armor, QR Code 1 Abstract This project explored the potential of QR technology to provide interactive experiences at museums. The team developed content for selected objects at the Higgins Armory Museum. QR codes installed next to these artifacts allow visitors to access a variety of minigames and fact pages using their mobile devices. Facts for the object are selected randomly from a pool, making the experience different each time the code is scanned, and the pool adapts based on artifacts visited, personalizing the experience. 2 Contents Contents........................................................................................................................... 3 Figures..............................................................................................................................6 Introduction ……………………………………………......................................................... 9 Double Edged Swords In Europe………………………………………………………...21 The European Bronze Age Sword……………………………………………….21 Ancient edged weapons prior to the Bronze Age………………………..21 Uses of European Bronze Age swords, general trends, and common innovations
    [Show full text]
  • Spuhr 2021 Isms™ Catalog
    2021 SPUHR 2021 ISMS™ CATALOG IDEAL SCOPE MOUNT SYSTEM™ 1 ABOUT THIS CATALOG Thank you for your interest in our products! This catalog contains the full assortment of scope mounts and separate rings that make up the ISMS™ product family. The order of presentation is from the lowest mount with no tilt to the highest with maximum tilt from the smallest ring size/tube diameter to the largest. If you cannot find a specific mount you are looking for, and you have a special requirement to fill, we are able to provide mounting solutions outside of our normal product range in this catalog. Such projects do require a minimum volume of 50 units. To make this catalog as universal as possible it does not contain any prices, but we have included all measurements and the weights of the products when mounted. We hope you will find this catalog to your liking and we welcome any feedback you may have. If you want to see more of our capabilities, please visit our website www.spuhr.com or www.spuhr.biz. Yours sincerely, Håkan Spuhr 2 CONTENT ABOUT THIS CATALOG ........................................................................................... 1 ABOUT ISMS ........................................................................................................... 3 PICATINNY MOUNTS .............................................................................................. 4 30 mm Unimounts .................................................................................................. 4 34 mm Unimounts .................................................................................................
    [Show full text]
  • Ar15 Semi—Automatic Instruction/ Safety Manual Caution
    AR15 SEMI—AUTOMATIC INSTRUCTION/ SAFETY MANUAL CAUTION: USE ONLY CLEAN, DRY, ORIGINAL, HIGH QUALITY COMMERCIALLY MANUFACTURED AMMUNITION IN GOOD CONDITON which is appropriate to the caliber of your firearm. We do not recommend the use of remanufactured or hand loaded ammunition because it may cause severe damage to yourself and/ or your rifle. Page 1 SECTION 1 PRECAUTIONS READ AND UNDERSTAND ALL THE FOLLOWING PRECAUTIONS BEFORE REMOVING THIS FIREARM FROM ITS PACKAGE. ! WARNING: IF THIS FIREARM IS CARELESSLY OR IMPROPERLY HANDLED, UNINTENTIONAL DISCHARGE COULD RESULT AND COULD CAUSE INJURY, DEATH, OR DAMAGE TO PROPERTY. CAUTION: PRIOR TO LOADING AND FIRING, CAREFULLY READ THIS INSTRUCTION MANUAL WHICH GIVES BASIC ADVICE ON THE PROPER HANDLING AND FUNCTIONING OF THIS RADICAL FIREARMS SYSTEM. However, your safety and the safety of others (including your family) depends on your mature compliance with that advice, and your adoption, development and constant employment of safe practices. If unfamiliar with firearms, seek further advice through safe handling courses run by your local gun clubs, NRA approved instructor, or similar qualified organizations. Page 2 NOTICE: Radical Firearms shall not be responsible for injury, death, or damage to property resulting from either intentional or accidental discharge of this firearm, or from its function when used for purposes or subjected to treatment for which it was not designed. Radical Firearms will not honor claims involving this firearm which result from careless or improper handling, unauthorized adjustment or parts replacement, corrosion, neglect, or the use of wrong caliber ammunition, or the use of ammunition other than original high quality commercially manufactured ammunition in good condition, or any combination thereof.
    [Show full text]
  • Manson Precision Receiver Accurizing System
    Manson Precision Receiver Accurizing System Rhomboidal and pavid Slim reinterred her sundries feign or municipalizes estimably. Bewhiskered and dorsiventral Shurlock often disorientates some suspiration jeopardously or gumshoe therapeutically. Toothsome Ned sometimes climb-downs any hypogyny objectivize thriftily. Austenite molecular structure in receiver accurizing your order to impact forging die was attached to It has a receiver accurizing and precision machined hand when needed. National Match Rifle, Serial No. Ups For Remington Centerfire Rifles MAGAZINE CLIP is best carrying cases for extra ammo; they spoke right knowledge the gun. Available in precision manufacturing, deeply serrated face! Winchester receiver accurizing system and precision receiver, butt plate screw only received and the systems, the barrel bore. Sold had designed by the receiver accurizing kit! If they are precision. Even directional change the receiver accurizing system for precise, fulton armory operating rod rail hand and flexibility. The replacement magazine followers should have three neat and evenly spaced spot welds attaching the stop to the follower. End to match category will enlarge due to. The magazines were rotated for even use and the rate of fire was measured during one of the twenty round bursts. It is precision receiver accurizing system was unable to do so you wont need to work was a manson. He fled to the jungle the same day. SPECS: Aluminum, anodized, red. The reamer has a FLOATING pilot that measures approx. Bush and receiver. SPECS: Stainless steel, belt finish. Tactical Forums discussion board www. Low maintenance, Parkerized finish resists corrosion and matches the rest of your rifle. This corn is therefore excellent turnover and fluctuate barely ever used.
    [Show full text]
  • Art of Precision
    2017 CATALOGUE ART OF PRECISION «Promtechnologia» (Industrial Technology) company directs careful attention to its products’ quality which allows it to gain some impressive results: Orsis rifles’ accuracy exceeds their most common counterparts’ results greatly. This reality is confirmed by the multiple winning scores of shooters participating in high-accuracy shooting international competitions with their Orsis rifles in hands. There is a parameter in ballistics called “minute of angle” (or MOA) which estimates accuracy of shooting and it is defined, as a rule, by a group of 3-5 shots. Rifles having MOA ratio less than 1 are called sniper rifles. «Promtechnologia» company guarantees that all Orsis rifles demonstrate accuracy not over 0.5 MOA and a number of models demonstrate even better performance. www.orsis.com 3 President’s Message 4 Orsis Special 6 Orsis SE T-5000 M 8 Orsis M-15 Carbine 12 Orsis AR-10 National Match 16 Orsis Hunting 20 Orsis 120/140 22 Orsis SE Hunter M 26 Orsis SE Alpine M 30 Marocchi Si12 / Walnut 34 T-5000 / 8-11 120/140 / 22-25 Varmint / 48-51 Marocchi Si12 / Plastic 36 Marocchi First-E 40 Marocchi First-E Deluxe 42 Orsis Sport 46 Orsis Varmint M 48 Orsis F-Class 52 Glock Pistols 54 M-15 / 12-15 Hunter / 26-29 F-Class / 52-53 Production 56 High-Technology Equipment 58 High-Precision Technologies 59 Exceptional Materials 60 Innovative Development 61 International Cooperation 61 AR-10 / 16-19 Alpine / 30-33 Glock / 54-55 Services 62 Rifle Barrels Replacement 63 Cerakote Coating Application 63 Technical Maintenance 64 Decoration & Engraving 65 Orsis Сustom 65 Dealer Network 66 Marocchi / 34-45 Contacts 66 HIGH-PRECISION FIREARMS SYSTEMS ORSIS 4 ORSIS ART OF PRECISION President’s Message 5 Dear friends! The first catalogue of «Promtechnologia» (Industrial Technology) We support our shooters’ aspiration to be the best hunters and company is now introduced for your kind attention and, as you will sportsmen.
    [Show full text]
  • Summary Description Semi-Automatic Sporting Rifle SIG-AMT Cal
    - Summary Description Semi-Automatic Sporting Rifle SIG-AMT cal. 7.62x51 mm (.308 Win.) Swiss Industrial Company CH- 8212 Neuhausen Rhine Falls/Switzerland Phone 053/81555 Telex 76156 sig ch - 3 - Contents l. Weapon theory Page l.l. Designation and purpose 5 1.2. Main components and accessories 6- 7 1.3. Dismantling and assembly 9 1.4. Cleaning and maintenance ll 1.5. Functional checks 12 2. Manipulation 2.1. Loading, reloading, unloading 13-14 2.2. Positions of firing, using normal ammunition 14 2.3. Sight adjustments 16 3. Technical data 17-18 - 4 - - 5 - l. Weapon theory 1.1. Designation and purpose The semi-automatic sporting rifle SIG-AMT is a delayed blow-back weapon with stationary barrel and semi-rigid breech. The cartridges are fed from magazines of 5, 10 or 20 rounds. A considerably reduced recoil and the bipod which lends the rifle a firm support, improves accuracy of aim in all types of fire. Next to the normal trigger, in latched neutral position, is a winter trigger. This can be un­ latched and shifted into engagement to allow firing in mittens. In the head of the breech casing is a loading indicator, affording a visual check as to whe­ ther the weapon is loaded or unloaded. - 6 - - 7 - 1.2. Main components Accessories The principal parts of the weapon are: - Magazines for 5, 10 or 20 rounds - Barrel, bolted firmly to the breech casing. - Sling Pull-through with string and wire brush Breech casing with 2 lock heads, carrying - Loading indicator holder handle, loading indicator, bolt, rear sight and cartridge ejector opening.
    [Show full text]
  • CASV Handguard for the FAL Rifle Note: the CASV-FAL System Will Not Fit on Rifles Using the G1 Or Similarly Profiled Barrels
    CASV Handguard for the FAL Rifle Note: The CASV-FAL System will not fit on rifles using the G1 or similarly profiled barrels Improper installation can result in damage. Do not attempt installation if you are not familiar with the firearm, tools and techniques mentioned. You are responsible for any damage or READ injury resulting from the improper use THIS! or installation of this product. Ensure the rifle is CLEAR and SAFE! Before installation, read Instructions, Warnings and Notes. NOTE: Make sure that the firearm is unloaded and safe before proceeding – if you are unsure of how, or uncomfortable with the proper clearing and safe handling of the firearm, do not proceed! We recommend that the installation of this part be done only by a qualified gunsmith or agency armorer. 1. Before proceeding, please inspect the handguard assembly and hardware to ensure that you are familiar with all of the parts. 1 - Upper handguard Assembly 2 - Lower handguard Assembly 3 - Forward mounting screw retaining clip 4 - Forward mounting screw 5 - Rear mounting cross screw 6 - Rear mounting clamping nut 7 - Upper Handguard retaining screws (6 for FAS, 8 for FAL) 8 - Picatinny Accessory Rails & Screws 2. Install the lower handguard section by sliding it over the front sight gas block, and rearward over the handguard retainer. After the lower section is in place, install the forward mounting screw from the right side of the handguard, ensuring that it goes through the front sight gas block. Note: only snug the screw enough to hold the lower handguard section in place. 3.
    [Show full text]
  • PM Crew Served Weapons Overview Small Arms Symposium & Exhibition
    TheThe Soldier:Soldier: America’sAmerica’s MostMost DeployedDeployed CombatCombat SystemSystem PM Crew Served Weapons Overview for the Small Arms Symposium & Exhibition National Defense Industrial Association 16-19 May 2006 BG James R. Moran COL Carl A. Lipsit Mr. Peter Errante Program Executive Officer Soldier PM Soldier Weapons Deputy PM Crew Served Weapons Crew Served Weapons 2 PM Soldier Weapons Programs List DEVELOPMENT WEAPONS PROCUREMENT Objective Individual Combat Weapon (OICW) 37. M101, CROWS, Remote Mount 1. OICW Increment I 38. M151E1 & M151E2 Protector Remote Wpn System (RWS) 2. OICW Increment II - XM25 Air Burst Weapon 39. MK19 Advanced Crew Served Weapons (ACSW) 40. Mod Kit 3. Advanced Crew Served Weapon (ACSW) Programs 41. Lightweight Adjustable Sight Bracket 42. Tactical Engagement Simulator (TES) SOLDIER ENHANCEMENT PROGRAMS 43. M107 Semi Automatic Long Range Sniper Rifle 4. XM26 - 12 Gauge Modular Accessory Shotgun System 44. M240B, 7.62mm Medium MG (MASS) 45. M240B Collapsible Buttstock 5. Joint Combat Pistol 46. M192, Light Weight Ground Mount For MG 6. Family of Small Arms Suppressors 47. Improved Bipod 7. M68 Close Combat Optics (Dual Source Qualification) 48. Improved Flash Suppressor 8. XM1068, 12 Gauge Non-Lethal Extended Range Round 49. Combat Ammunition Pack 9. XM1022, Sniper Ammunition for M107 50. M240B Short Barrel 10. XM110 - 7.62 Semi-Automatic Sniper System (SASS) 51. M240B Improved Buttstock 11. Close Quarters Battle Kit 52. Sling Assembly for the M240B 12. XM1041/XM1042/XM1071 - Close Combat Mission 53. Short Barrel Capability Kit 54. M249, 5.56mm Squad Automatic Weapon 13. Advanced Sniper Accessory Kit (ASAK) 55. M192, Lightweight Ground Mount For MG 14.
    [Show full text]
  • 2020 Product Catalog Tm
    TM 2020 PRODUCT CATALOG TM SENTRY Products Group. We Live to Protect! 2 We are proud to introduce our 2020 product assortment featuring new products, new categories and further expansion of our tactical nylon line. While the nylon line had seen steady growth, a visit from a key customer in the summer of 2019 changed the pace of our development creating a combination of lightweight and configurable components with the flexibility to meet changing mission demands. For the latest project check out the Gunnar Series Plate carrier featured on page 10. Along with our nylon line developments the hybrid Hexmag magazine which combined the best attributes of metal and polymer technologies was launched to support the Glock 17. Additional platforms are in the works as we continue to expand the Hexmag line up. Whether you protect your home, family, or country, our commitment to you is simple – we will continue to produce the best, most innovative product on the market to enhance your experience. We are so confident that we back each product with a hassle- free Lifetime Warranty, protecting your investment. From the team at SENTRY, thank you for your support and confidence. TABLE OF CONTENTS MAGAZINES . .4-7 ON GUN ACCESSORIES . 8-9 PLATE CARRIER AND ACCESSORIES . 10-13 BELTS AND POUCHES . 14-21 SLINGS. .22-23 OPTIC COVERS. .24-29 FIREARM COVERS . .30-33 CLEANING AND LUBRICATION. .34-39 BAGS. .40-41 OEM PROGRAMS. .42-43 3 When every round counts™ 4 ™ POLYHEX2 The proprietary advanced composite that all Hexmag magazines are made from delivers superior strength and reliable performance across the modern sporting rifle and pistol spectrum.
    [Show full text]
  • Firearms Manuals
    A Division Of ARMALITE®, INC OWNER’S MANUAL FOR M-15™ RIFLES AND CARBINES READ THIS MANUAL THOROUGHLY, PARTICULARLY THE WARNINGS, BEFORE USING THIS FIREARM! IT’S IMPORTANT! ©2015 Armalite®, Inc., All rights reserved. Armalite®, Inc. October 2015 Rev 25 (I-7) 525 E. Pinnacle Peak Rd. Ste 100 P/N: MANUAL Eagle 15 Phoenix, AZ. USA 85024 623-780-1050 www.Armalite.com 1. READ THIS FIRST! Throughout this manual you will find WARNINGS and/or CAUTIONS printed in bold print. All WARNINGS and CAUTIONS should be read carefully and followed completely. WARNINGS discuss issues that could result in damage to your firearm, or injury or death to you or a bystander. CAUTIONS discuss issues that could result in damage or malfunction of your firearm. WARNING: IT IS YOUR RESPONSIBILITY TO ASSURE THAT YOUR FIREARM IS HANDLED, FIRED, AND STORED SAFELY AND RESPONSIBLY AT ALL TIMES. This manual provides instructions on the operation and maintenance of your Eagle Arms firearm. Read and understand it carefully before you try to use your firearm. Your safety, and that of those around you, depends on your knowledge of your firearm and on your knowledge of safety rules common to all firearms. Please study the common-sense safety rules noted in this manual. Your first responsibility as a gun owner is always safety! Your second responsibility as a gun owner is security. Make sure that your firearm remains in responsible hands…YOURS! Don’t become an unwitting partner in a crime or tragedy: make sure your firearm is properly secured. Lock it in a secure storage container or, if none is available, remove the bolt and bolt carrier assembly and store it separately.
    [Show full text]
  • Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology
    University of Nebraska - Lincoln DigitalCommons@University of Nebraska - Lincoln Anthropology Department Theses and Dissertations Anthropology, Department of 4-2013 Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology Eric T. Skov University of Nebraska-Lincoln, [email protected] Follow this and additional works at: https://digitalcommons.unl.edu/anthrotheses Part of the Anthropology Commons Skov, Eric T., "Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology" (2013). Anthropology Department Theses and Dissertations. 30. https://digitalcommons.unl.edu/anthrotheses/30 This Article is brought to you for free and open access by the Anthropology, Department of at DigitalCommons@University of Nebraska - Lincoln. It has been accepted for inclusion in Anthropology Department Theses and Dissertations by an authorized administrator of DigitalCommons@University of Nebraska - Lincoln. Experimentation in Sling Weaponry: Effectiveness of and Archaeological Implications for a World-Wide Primitive Technology by Eric Skov A THESIS Presented to the Faculty of The Graduate College at the University of Nebraska In Partial Fulfillment of Requirements For the Degree of Master of Arts Major: Anthropology Under the Supervision of Professor LuAnn Wandsnider Lincoln, Nebraska May, 2013 EXPERIMENTATION IN SLING WEAPONRY: EFFECTIVENESS OF AND ARCHAEOLOGICAL IMPLICATIONS FOR A WORLD- WIDE PRIMITIVE TECHNOLOGY Eric Thomas Skov, M.A. University of Nebraska, 2013 Adviser: LuAnn Wandsnider The sling is a simple, cheap and effective weapon that was widely distributed among prehistoric and historic populations. Well-known archaeological and textual evidence attests to its widespread military usage in Europe, South America and Central America. However, ethnographic and archaeological evidence also suggest that the sling was widely distributed among Native American populations.
    [Show full text]