DOCSLIB.ORG

Aero Tool List (Rev. 11 01/01/02)

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Aero Tool List (Rev. 11 01/01/02) Aero Tool List (Rev. 11 01/01/02) TOOL LIST Coveralls Dust masks (1 box) AERO 130 & 131 GENERAL - REQUIRED TOOLS Feeler Gauge Set (.0015” through .035”) Safety glasses or Goggles, (OSHA approved Z 87) Hacksaw blades 18, 24, 32 teeth per. inch Ear protectors (ANSI Stand. 53.19, NRR of 23-28 decibels) Sockets, deep 3/8” drive, 3/8” through 3/4” Respirator (particulate to a size of .05 NG/M) Magnifying Glass, 10 power min. Ratchet 1/4” drive Rule, steel 6” with English & Metric scales Ratchet 3/8” drive (pocket clip type for field use) Breaker bar 1/4” drive Rule, steel 12” with 100ths & 32nds scales (drawing & Extension 1/4” drive approximately 4” long sheetmetal) Extension 1/4” drive approximately 6” long Multimeter Extension 3/8” drive approximately 6” long Tool Box and lock Extension 3/8” drive approximately 3” long Universal joint 1/4” drive AERO 132, 134 & 136 POWERPLANTS - REQUIRED Universal joint 3/8” drive Brass Punches 1/4”, 3/8”, 1/2” Speed handle 3/8” drive Hex Key set (Allen wrenches) Socket set 1/4” drive 12 point standard (10 sockets) Magnet, telescoping handle, flexible head 3/16”, 7/32”, 1/4”, 9/32”, 5/16”, 11/32”, 3/8”, 7/16”, 1/2”, Scissors 10” 9/16” Screwdriver, Magnetic 12” long using replaceable bits Socket set 3/8” drive 12 point standard (12 sockets) Screwdriver, Phillips stubby 1/4”, 5/16”, 11/32”, 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”, Screwdriver, Slotted stubby 3/4”, 13/16”, 7/8” Socket, Sparkplug 7/8” 6pt or 12pt, 3/8” or 1/2” drive, with or Wrenches, combination 12 point (9 wrenches) without holding magnet 5/16”, 11/32”, 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”, 3/4” Sockets Universal 1/4” drive 5/16” through 1/2” 12 point Screwdrivers (8 tools) Sockets Universal 3/8” drive 1/2” through 3/4” 12 point slotted: 3 1/4”, 6 1/2”, 8 13/32”, 10 15/16”, 13 1/2” (approx. Stone, Blending (Arkansas) for blending titanium blades overall length) Tape Measure, roll up 10 feet by 1/2” or 3/4” Phillips: 3 1/4”, 6 21/32”, 8 13/32” (approx. overall length) Wire twisters (safety wire pliers) Screwdriver-offset slotted 4” long 3/8” Breaker Bar Pliers (4 tools, approx. size) needle nose 7 1/8”, channel lock 9 1/4”, regular 7 1/2”, AERO 133, 135 & 137 AIRFRAME - REQUIRED diagonal cutter 7 1/4” “C” clamps 2”, two to four Pliers, Duck Bill 7 3/4” Dividers Pliers, Wire stripper & crimp Drill bits (sheet metal) #11, #21, #30, #40, (3 each) Vise grips 7” Files, set of 4 needle (small files) Hammer 16 oz. Ball Peen Protractor, movable arm (could be incorporated with square) Hammer 16 oz. Plastic Tip Putty Knife, stiff blade approximately 1 1/2” wide Mallet, rubber or dead blow Razor with holder (Exacto Knife or the like) Punch & Chisel Set: (11 tools, approx. size) Scribe Chisel Gauge 2 5/8” long Snips, Aircraft sheetmetal: straight cut, left cut, right cut Center Punch 6” long Square 12” (could be incorporated with protractor) Pin Punches 3/32” dia., 1/8" dia., 5/32” dia., 3/16” dia. Squeeze Clamps 3” two to four Starter Punches 5 1/4” long, 6” long, 6 1/4” long Flat Chisels 3/8” dia., 1/2” dia., 5/8” dia. HIGHLY RECOMMENDED - NOT REQUIRED File Set: round, half round, flat (8” to 10” long with handles) Air Chuck for filling tires File brush and pick Blow gun, compressed air Fingers 17 3/4” long Brushes, stainless steel, nylon (tooth brush size) Flashlight Calipers, inside-outside or one of each Hacksaw for 10” to 12” blades Core Remover for tire valves Mirror, Inspection 2 1/8” by 3 1/2” telescoping Drills #1 to #60 (1 set) Thread Pitch Gauge (English) Drills fractional 1/16” to 1/2” Adapter sockets: Drill Gauge, # 3/8” female to 1/4” male Drill Gauge, fractional 1/4” female to 3/8” male Files, Swiss (one set) various shapes, about 6 inches long Compass (drawing) File, Vixen 8” to 10” long Gasket Scraper Goggles, welding, brazing Hammer 8oz Ball Peen Hole Finder 3/32”, 1/8” Screwdriver offset Phillips 4” long Snap-Ring Pliers internal-external with replaceable tips Solder, Rosin Core Soldering Iron, small (at least 40 watts) Tire Pressure Gauge Wrenches, Crows Foot 7/16” through 1” (one set) Wrenches, midget combination, 5/16”, 3/16”, 13/64”, 7/32”, 15/64”, 1/4”, 9/32”, 5/16”, 11/32”, 3/8”, 7/16” OPTIONAL - NOT REQUIRED TOOLS Brush, Parts Cleaning Caliper, Dial 6” Cotter Key Remover Extension 1/2” drive 3” long Extension 1/2” drive 5” long Flaring Tool set with tube cutter (aircraft 37 degree) Micrometer, 1” with carbide faces & vernier scale Nut Drivers 3/16”, 7/32”, 1/4”, 9/32”, 5/16”, 11/32”, 3/8”, 7/16”, 1/2”, or 1/4” drive handle for sockets Ratchet 1/2” drive Rollaway tool box Phillips tips Socket Set 1/2” drive 7/16” to 1” (12 point) Torque Wrench 150 to1000 inch pounds Torque Wrench 0 to 200 foot pounds Tool Marker (electric etcher) Universal Joint 1/2” drive Wrenches, open end 45 degree angle head, 3/8” to 1”.
Load more

Recommended publications
  • 1St Year Diesel and Heavy Equipment Mechanics Required Tool List The
    1st Year Diesel and Heavy Equipment Mechanics Required Tool List The following tools list represents a starter set of diesel mechanics tools. Laptop or tablet able to accesses the internet, work with various manufactures websites and learning platforms, (most will without issue) . 1/4” Drive set in a plastic box (Standard and Metric) 3/8” Drive Ratchet 3/8” 12” Extension 3/8” 6” Extension 3/8” 2” Extension 3/8 U-Joint 3/8” Drive sockets from 3/8 to ¾ Metric 3/8 Impact Sockets From 8-19 mm 12 pt. 3/8 Impact Wrench 3/8’ Drive Allen sockets (standard and metric) 3/8” Torque Wrench 1/2” Drive Ratchet 1/2” Drive Breaker Bar 18” 1/2" Extension 10” 1/2" Extension 6” 1/2” Extension 2” 1/2-3/8” Adapter 1/2” U-joint 1/2" Drive Sockets from 1/2" to 1 1/8” Metric 1/2” Impact Drive Sockets from 12-24 mm 12pt. ½” Impact Wrench ½” Torque Wrench ½ Impact Wrench Combination Wrenches from 1/4" to 1 5/16” Metric Combination Wrenches 8 mm 10mm 11mm 13mm 14mm 15mm 16mm 17mm 18mm 19mm 20 mm 22mm 24mm Short Handle Combination Wrenches Standard and Metric Flat Chisels with 3/8” 1/2" & 5/8” Blade Widths Starter Punches with 3/32” 1/8” &1/4" Point Diameter Pin Punches with 3/32” 1/8” & 1/4” Point Diameter Center punch Pry Bar with a roll head one end and a point on the other Flat pry Bars 4 piece set Screw Drivers: Blade Tip Width Blade Length 1 @ 1/4" 1 1/2" 1 @ 3/16” 2 1/2" 1 @ 1/4" 4” 1 @ 5/16” 6” 1 @ 3/8” 8” Philips Bit size #2 1 1/2'” Philips Bit Size #1 3” Philips Bit Size #2 4” Torx Bit Set Could be bought as a set with screw drivers Allen Wrenches (standard and Metric) Misc.
    [Show full text]
  • Textbook/Supplies
    FAST TRACK MACHINE TOOL TECHNOLOGY (23 Credit Hours) 2021-2022 TEXTBOOKS & REQUIRED SUPPLIES TEXTBOOK TITLE EDITION PUBLISHER ISBN 1. Precision Machining Technology 3rd Edition Delmar Cengage Learning. ISBN: 978-1-337-79530-2 2. Machine Trades Blueprint Reading 7th Edition Goodheart Wilcox ISBN: 978-1-645-64656-3 3. Shop Reference for Students and Apprentices 2nd Edition Industrial Press ISBN: 978-0-831-13079-4 TEXTBOOKS (Required) RECOMMENDED: Machinery Handbook 31st Edition Industrial Press, Incorporated ISBN: 978-0-831-13731-1 Students may purchase textbooks from the Washburn Tech Bookstore, or the vendor of their choice. • • Safety glasses, clear lens (must meet Z87 safety standards) Mighty mag magnetic base • Thread measuring wire set • Toolbox with lock • Deburring Tool • 6” steel ruler • (10) each – 3/8 square tool bits (3” long) • 0-1” micrometer TOOLS • (6) each - #4 combined drill & countersink (Required) • 6” dial calipers • Hacksaw, with (6) blades • 60 degree center gauge • Edge finder • Drill point gauge • Allen wrench set (inch) – quality ball driver set • 10” mill file • Magnetic base with 1” travel indicator • Thread pitch gauge (metric & inch) • Scientific calculator – TI-30X IIS or equivalent • Sharpie marker SUPPLIES • Scribe (Required) • Three ring notebook (with page protectors) Students may purchase required tools and supplies from the vendor of their choice. Washburn University prohibits discrimination on the basis of race, color, sex, religion, age, national origin, ancestry, disability, marital or parental status, sexual orientation/gender identity, genetic information, or other non-merit reasons, in University programs and activities, admissions, educational programs or activities and employment, as required by applicable laws and regulations.
    [Show full text]
  • PUNCHES and CHISELS Punches and Chisels the Anvil End on Heads of Snap-On® Punches and Chisels Are Machined to a Modified Parabolic Curve
    PUNCHES AND CHISELS Punches and Chisels The anvil end on heads of Snap-on® punches and chisels are machined to a modified parabolic curve. This design directs the striking force to the center of the tool head to allow slow metal displacement. The parabolic curve controls mushrooming to reduce chipping and splitting. Heads should be re-dressed to their original shape with hand files as necessary. The tough steel alloy is machined and differentially heat treated for optimum performance. The hardness of the striking head is reduced to help toughness and add qualities that result in a slower mushrooming of the striking surface. PPC250BK Punch and Chisel Set. PPC100AK Punch and Chisel Set. ncludes 24 pcs. in KB2179 kit bag: Includes 10 pcs. in KB2175 kit bag: PPC1A PPC106A PPC205A PPC820B PPC812B PPC828B PPC15B PPC3A PPC108A PPC206A PPC824B PPC816B PPC12B PPC19B PPC250BK PPC4A PPC110A PPC208A PPC12B PPC820B PPC13B PPC103A PPC112 PPC210A PPC14B PPC824B PPC14B PPC104A PPC203A PPC812B PPC15B PPC100AK PPC105A PPC204A PPC816B PPC19B PPCD70BK Punch and Chisel Set. PPC210BK Punch and Chisel Set. Includes 7 pcs. in KB2183 kit bag: Includes 22 pcs. in KB2178 kit bag: PPC103A PPC106A PPC110A PPC1A PPC105A PPC204A PPC816B PPC104A PPC107A PPC5A PPC106A PPC205A PPC820B PPC105A PPC108A PPC3A PPC108A PPC206A PPC824B PPC210BK PPC4A PPC110A PPC208A PPC828B PPC103A PPC112 PPC210A PPCD70BK PPC104A PPC203A PPC812B PPCS60BK Punch and Chisel Set. Includes 6 pcs. in KB2185 kit bag: PPC715BK Punch and Chisel Set. PPC203A PPC205A PPC208A Includes 16 pcs. in KB2182 kit bag: PPC204A PPC206A PPC210A PPC1A PPC104A PPC203A PPC208A PPC3A PPC105A PPC204A PPC812B PPC4A PPC106A PPC205A PPC816B PPC715BK PPC103A PPC108A PPC206A PPC820B PPCS60BK PPC50AK Punch and Chisel Set.
    [Show full text]
  • ASSAM SCIENCE and TECHNOLOGY UNIVERSITY B.TECH INDUSTRIAL and PRODUCTION ENGINEERING 5Th SEMESTER
    ASSAM SCIENCE AND TECHNOLOGY UNIVERSITY Guwahati Course Structure and Syllabus (From Academic Session 2018-19 onwards) B.TECH INDUSTRIAL AND PRODUCTION ENGINEERING 5th SEMESTER ASSAM SCIENCE AND TECHNOLOGY UNIVERSITY Course Structure (From Academic Session 2018-19 onwards) B.Tech 5th Semester: Industrial and Production Engineering Semester V/ B.TECH/IPE Hours per Credit Marks Week Sl. No. Sub-Code Subject L T P C CE ESE Theory 1 IPE181501 Manufacturing Process – II 3 0 2 4 30 70 2 IPE181502 Machine Tool Technology 3 0 0 3 30 70 3 IPE181503 Plant Layout and Material Handling 3 0 2 4 30 70 Mechanisms and Dynamics of 4 ME181503 3 0 0 3 30 70 Machines 5 ME181505 Engineering Inspection and Metrology 3 0 0 3 30 70 6 HS181506 Engineering Economics 3 0 0 3 30 70 Practical 1 IPE181512 Machine Tool Technology Lab 0 0 2 1 15 35 2 ME181515 Engineering Inspection and Metrology Lab 0 0 2 1 15 35 3 SI181521 Internship-II (SAI-Academia) 0 0 0 1 - 100 TOTAL 18 0 8 23 210 590 Total Contact Hours per week: 26 Total Credits: 23 Assam Science and Technology University Page 1 of 13 Detailed Syllabus: Hours per week Credit Course Code Course Title L-T-P C IPE181501 Manufacturing Process – II 3-0-2 4 Course Outcomes (CO): At the completion of the course the student will be able: 1. To understand the various plastic deformation phenomenon of metals. 2. To evaluate and understand the suitability of various metal forming processes along with latest advancements in forming technology & their practical Importance 3.
    [Show full text]
  • ED312379.Pdf
    DOCUMENT RESUME ED 312 379 CE 053 427 TITLE Vocational Education Equipment StaLtards. Revised. INSTITUTION North Carolina State Dept. of Publi7 Instruction, Raleigh. Div. of Vocational Educatioa. PUB DATE Jan 89 NOTE 236p. PUB TYPE Guides Non-Classroom Use (055) EDRS PRICE MF01/PC10 Plus Postage. DESCRIPTORS Appropriate Technology; *Educational Equipment; Educational Resources; *Equipment Evaluation; *Equipment Standards; *Equipment Utilization; *Facility Inventory; Purchasing; *Vocational Education ABSTRACT This document lists equipment and equipment-like supplies used in classrooms in nine vocational education programs in North Carolina. It was prepared to help local educational agencies assess the adequacy of their vocational education equipment; identify and plan for equipment purchases to meet the minimum requirements; and determine the feasibility of offering a new vocational course sequence. An introduction explains the handbook's purpose and its organization. It is followed by a short list of equipmsm.: and supplies common to all vocational programs. The bulk of the handbook consists of tables that list the equipmenttnd supplies used in agricultural education, business and office education, career exploration, health occupations education, home economics education, industrial arts /technology education, marketing education, principles of technology, and trade and industrial education. In addition to each kind of equipment and supply, the tables suggest their quantity (per lab or per student). The appendix contains an excerpt from
    [Show full text]
  • Catalog25small.Pdf
    We dedicate this catalog back in. That was not the case. The office and plant areas of the building were completely destroyed. There was nothing to In memory of our father go back to. (Continued on page 150) Warren L. Fuller Guarantee It is with our deepest regrets that we inform you of the This catalog illustrates and describes all the types of loss of our father, Warren L. Fuller. His passing was due to Countersinks, Counterbores, Plug Cutters and Drills Hurricane Katrina as he was a resident of the Gulf Coast of manufactured under the name Fuller and fully guaranteed Mississippi. He survived and escaped the hurricane only to in normal use. The Fuller logo appears near each tool die of a heart attack one day later in a high school shelter picture manufactured by us. where he was waiting for his companion of 20 years. She had Also included are various types of drills, bits, cutters, and been injured during the escape and was hospitalized. We had specialty type tools, made by reputable American traveled to his town to rescue him and were only a few miles manufacturers, worthy of showing in our catalog. These are from him when he passed. As owner of W. L. Fuller, Inc., he to supplement our own line of tools and are also fully had prepared his children to continue with the same service guaranteed. and quality you have become accustom to. We look forward We have now added a few very useful types of tools that to continuing the business relationships he enjoyed and are just not available in this country.
    [Show full text]
  • Punches / Chisels the Anvil End on Heads of Snap-On® Punches and Chisels Are Machined to a Modified Parabolic Curve
    Punches / Chisels The anvil end on heads of Snap-on® punches and chisels are machined to a modified parabolic curve. This design directs the striking force to the center of the tool head to allow slow metal displacement. The parabolic curve controls mushrooming to reduce chipping and splitting. Heads should be re-dressed to their original shape with hand files as necessary. The tough steel alloy is machined and differentially heat treated for optimum performance. The hardness of the striking head is reduced to help toughness and add qualities that result in a slower mushrooming of the striking surface. Stock Hex Point/ Length Stock Hex Point/ Length No. Size, in. Edge, in. in. No. Size, in. Edge, in. in. Punch and Chisel Accessories PPC808A 1/4 1/4 5 Flat Chisels PPC1A — — 2 5/8 PPC812B 5/16 3/8 5 1/2 Chisel Gauge PPC816B 7/16 1/2 6 PPC5A — — 6 15/16 PPC820B 1/2 5/8 6 1/2 PPC1A PPC5A Punch/Chisel Holder PPC824B 5/8 3/4 7 1/4 11 7 Center Punches PPC3A 5/16 1/8 5 PPC828B /16 /8 8 PPC832B 7/8 1 9 PPC4A 7/16 3/16 6 BPPC1878 7/8 1 9 PPC6B 5/8 5/16 7 PPC820LB 1/2 5/8 16 Long Flat Chisels PPC714B 9/16 5/32 14 Pin Punches PPC103A 9/32 3/32 4 7/32 PPC104A 5/16 1/8 4 3/4 PPC105A 3/8 5/32 5 3 3 1 PPC106A /8 /16 5 /4 PPC12B 3/8 5/16 6 Half Round Nose Cape PPC107A 3/8 7/32 5 1/4 PPC108A 7/16 1/4 5 3/4 Chisels PPC110A 1/2 5/16 5 1/4 PPC112 9/16 3/8 5 1/4 Starter Punches PPC203A 5/16 3/32 5 1/2 3 1 3 PPC204A /8 /8 5 /4 PPC13B 5/16 1/4 5 5/8 3 5 Cape Chisels PPC205A /8 /32 6 PPC14B 3/8 5/16 6 PPC206A 7/16 3/16 6 1/4 PPC208A 1/2 1/4 6 3/4 PPC210A 9/16 5/16 7 1/4 PPC15B 7/16 7/32 6 Diamond Point Chisels PPC19B 3/8 1/8 5 3/4 PPC250AK PPC250AK Punch and Chisel Set Includes the following 25 pcs.
    [Show full text]
  • Littlemachineshop.Com Catalog 34 Mid-2021
    C A T A L O G Mid-2021 34 The premier source of tooling, parts, and accessories for bench top machinists. www.LittleMachineShop.com (800) 981 9663 396 W Washington Blvd #500 Pasadena CA 91103 Email: [email protected] Pricing Note Prices in this catalog are correct at the time of printing. The 25% additional tariff imposed on many of our imported products remains in place. And, of course, COVID continues to affect supply chains, factory production—and prices. Please check our website or call us to get the latest prices. Welcome to LittleMachineShop.com… …the premier source of machines, tooling, parts, and accessories for bench top machinists. We focus on best-in-class machines and we offer tools, accessories, and replacement parts for: • Bench top lathes • Bench top milling machines • Small band saws • Bench top grinders Products we support are sold by LittleMachineShop.com, Grizzly Industrial, Harbor Freight Tools, Micro-Mark, Busy Bee Tools, and others. Besides the products shown in this catalog, we have virtually every replacement part for the mini lathes, mini mills, and micro mills sold by these companies. Visit our website at www.littlemachineshop.com to see large, full-color pictures along with more products and more information than we can fit in this catalog. Check our website at www.littlemachineshop.com for current prices. Prices are subject to change without notice. Contents HiTorque Mini Mill (SX2) Accessories 51 CNC Machines Micro Mill (X1) Accessories 52 Accessories 9 Micro Mill (X1) Assemblies 52 CNC Lathes 9 Mini
    [Show full text]
  • Using Machine Vision to Develop an On-Machine Thread Measurement System for Computer Numerical Control Lathe Machines
    Proceedings of the International MultiConference of Engineers and Computer Scientists 2019 IMECS 2019, March 13-15, 2019, Hong Kong Using Machine Vision to Develop an On-Machine Thread Measurement System for Computer Numerical Control Lathe Machines Yi-Cheng Lee and Syh-Shiuh Yeh, Member, IAENG greatly increase and manual detection errors can easily result. Abstract—Thread inspection is a very important step in Therefore, when a computer vision system is used for modern industrial inspection and is also the key to guaranteeing noncontact thread measurement, it can measure multiple product quality. However, the traditional contact measurement items at the same time and measure smaller threads. In this method is time-consuming and expensive. This study developed an automatic noncontact measurement system that can be used case, it will not be limited by the size of the measurement to on-machine measure thread dimension based on machine instrument. In-situ measurement can also be realized during vision for computer numerical control (CNC) lathe machine the production process. This reduces the measurement time tools. During the measurement process, backlighting was used to and manual detection error. Therefore, this study develops a obtain the image of a thread profile. Then, a machine vision noncontact thread dimension measurement method that is algorithm was developed to analyze the obtained thread images suitable for the production line to on-machine measure thread in order to capture the thread profile coordinate points and compute the dimensions of the thread pitch and thread depth. dimensions in a rapid and automated approach. The experimental results showed that the maximum difference Image recognition and dimension measurements are the between the measured dimensions and real dimensions is around two major development directions of machine vision.
    [Show full text]
  • Tube Fitter's Tool
    TUBE FITTER’S TOOL KIT THE ULTIMATE SET OF FABRICATION TOOLS Swagelok Bangalore | Chennai | Delhi | Hyderabad Features • Set of Swagelok tools & accessories designed specifically for fabricating tubing systems • Easy to find the right tool for the job • 1/4” - 1/2” and 6 - 12mm kits • Lockable, water resistant case with wheels for easy transportation • Two variants - Master Installers Kit and Compact Inspectors Kit www.swagelok.com/bangalore www.swagelok.com/delhi Tool Kits Finding the right tool for the job will not be an issue when you have Tube Fitter’s Toolkit on your jobsite. The toolkit contains the complete set of Swagelok tools and accessories specifically for fabricating tubing systems. These set of tools are designed for use with the three most common tube sizes - 1/4, 3/8 and 1/2” OD (Outside Diameter) tubing. All the tools are securely placed in a lockable, water resistant case with wheels to make transportation easy. The tool kits are available in Imperial and Metric sizes. Master Installers Kit Components (Imperial) Item Description Size Part Number Ordering No: KIT-MI-IN (Imperial) Tube Benders 1 Hand Tube Bender 1/4” MS-HTB-4T KIT-MI-MM (Metric) 2 Hand Tube Bender 3/8” MS-HTB-6T 3 Hand Tube Bender 1/2” MS-HTB-8 Gap Inspection Gauges 4 Gap Inspection Gauge 1/4” MS-IG-400 5 Gap Inspection Gauge 3/8” MS-IG-600 6 Gap Inspection Gauge 1/2” MS-IG-810 Wrenches/Pre-swaging Tools 7 Ratchet Wrench 1/4” MS-RW-400 8 Ratchet Wrench 3/8” MS-RW-600 9 Ratchet Wrench 1/2” MS-RW-810 10 Pre-swaging Tool 1/4” MS-ST-400 11 Pre-swaging Tool 3/8” MS-ST-600 12 Pre-swaging Tool 1/2” MS-ST-810 13 Tee Wrench 1/4” MS-TW-4 14 Tee Wrench 3/8” MS-TW-6 15 Tee Wrench 1/2” MS-TW-8 Tube Prep Tools/Accessories 16 Snoop Leak Detector MS-SNOOP-8OZ 17 Tube Cutter 3/16” - 1” MS-TC-308 18 Tube Cutting Wheel (5 No’s) MS-TCW-308 19 Tube Deburring Tool 3/16” - 1 1/2” MS-TDT-24 Kits assembled for metric cases have 6mm, 10mm & 12mm 20 Thread Pitch Gauge MS-TIK-PG 21 1/4” Teflon Tape 1/8” - 3/8” MS-STR-4 tools and accessories in lieu of 1/4”, 3/8” and 1/2”.
    [Show full text]
  • Technical Information Index HOSES
    Technical Information Index HOSES Assembly Length .......................................... 300 - 301 Hex Dimensions ......................................................321 ONE-PIECE B SERIES Cautionary Statement & Limited Warranty ..........323 Hydraulic Hose Sizing Nomogram ........................297 Conversion Charts ........................................ 319 - 320 Installation & Assembly..................................302-303 Fitting Identification ...............................................304 Pressure & Distance Conversions ........................ 319 Fitting Identification - American ................. 306 - 310 Pressure Drop International Chart ......................299 ONE-PIECE Fitting Identification - British ................................ 311 Pressure Drop U.S. Chart ......................................298 D SERIES Fitting Identification - French ................................ 312 Safety Guide .................................................. 294 - 296 Fitting Identification - German .....................313 - 314 Temperature Conversions .....................................320 Fitting Identification - Japanese ..................315 - 316 Thread Type .............................................................305 F & P SERIES Torque Data ....................................................317 - 318 ONE-PIECE TWO-PIECE FERRULES (A & PFR SERIES) TWO-PIECE INSERTS TWO-PIECE INSERTS (A SERIES) TWO-PIECE FERRULES & INSERTS (X & Z SERIES) INTERLOCK RELEASE QUICK EQUIPMENT ASSEMBLY INFORMATION TECHNICAL Because
    [Show full text]
  • Definitions of General Technical Skills1 Definitions of Knowledge2
    Appendix Definitions of General Technical Skills1 Equipment Maintenance — Performing routine maintenance on equipment and determining when and what kind of maintenance is needed. Equipment Selection — Determining the kind of tools and equipment needed to do a job. Installation — Installing equipment, machines, wiring, or programs to meet specifications. Operation and Control — Controlling operations of equipment or systems. Operation Monitoring — Watching gauges, dials, or other indicators to make sure a machine is working properly. Operations Analysis — Analyzing needs and product requirements to create a design. Programming — Writing computer programs for various purposes. Quality Control Analysis — Conducting tests and inspections of products, services, or processes to evaluate quality or performance. Repairing — Repairing machines or systems using the needed tools. Technology Design — Generating or adapting equipment and technology to serve user needs. Troubleshooting — Determining causes of operating errors and deciding what to do about it. 2 Definitions of Knowledge Administration and Management — Knowledge of business and management principles involved in strategic planning, resource allocation, human resources modeling, leadership technique, production methods, and coordination of people and resources. Biology — Knowledge of plant and animal organisms, their tissues, cells, functions, interdependencies, and interactions with each other and the environment. Building and Construction — Knowledge of materials, methods, and the tools
    [Show full text]