Trident Quick Start Guide
Total Page:16
File Type:pdf, Size:1020Kb
G) Trident Underwater Drone. ® Tail strap - Improves tether integrity when handling Trident via tether. @ Tether & charger connection point. @ 25m tether - Kevlar-reinforced data cable that sends video and control data from the Topside to Trident. It has the same D-ring connector on each side. @ Topside - Sends video and control data to and from Trident to the controller via WiFi. /?',® @ Trident wall charger - All connection points must be dry before charging. Attach �� D-ring connector to Trident only. (8) (J)rim T weights - To maintain neutral buoyancy in saltwater, attach to bottom of Trident. This location is indicated by a weight symbol. (8) Controller - To operate the Trident. (9) (9) HDMI cable - To charge the Controller and download video. Back Controller Trident Trident Topside wall and charger tether and HDMI cable Trident quick-start Refer to safety guidelines in complete manual before diving your Trident. G) Charge Trident Battery \I/ (Red light) � Charging /1\I \I/ (Green light) Fully charged Always disconnect the charger from Trident Screw the charger first, then from the wall. Do not unplug the connectorto Trident. charger from the wall while still connected to Trident, otherwise battery will slowty drain. *Afterabout 3 hours Trident will be fully charged. ® Charge the Controller and Secure the Lanyard O Attach the HDMI cable When controller is to the Controller's Micro charged, detach the Check that the USB charging port HDMI cable and lanyard is securely (located to the left of the return it to the box. attached to the audio jack) and to a Green light means Controller. computer. Controller is charged. Trident quick-start Refer to safety guidelines in complete manual before diving your Trident. by attaching Topside and tether Screw the tether. _/ To power on, Tighten screw extra to the Topside e: screw the tether to 1 /4 turn on both (ships connected). Trident. To power off, topside and Trident unscrew tether from to ensure proper * Topside does not needto be the Trident. connection. charged. @Link Trident and Controller * Fully charge the controller before a Trident e.div (See step two above.) Access WiFi settings Flip topside / tether Wait about a minute on the controller and reel over to find your: for all 3 status lights connect to topside. SSID: Trident-XXXX located on the topside. Refer to next pages PASSWORD:XXXXXXXX for details. (case sensitive) Trident quick-start Refer to safety guidelines in complete manual before diving your Trident. Linking Trident and Controller (continued) 1. Power the Controller on 5. Press "Back to home screen" button 2. Swipe up (no password) 6. Open the app "OpenROV Cockpit" 3. Check WIFI connection by: 7. Choose either "Pilot," "Past Dives," "Settings," or a. Choose "Settings" then select "WIFI" b. Choose "Trident-4CB7" "Maintenance" screen. Complete desired operations. c. Choose "Connect" (may need to 8. If desired, use "Back" button to return to previous step and enter password) open an alternate screen (e.g., "Past Dives.") (5) Attach Trim Weights (only for saltwater) Trim weights are Trident is neutrally Screw trimweights found close to the bouyant in fresh to the underside of tether reel, in the water. For neutral Trident. This location foam at the bottom of buoyancy in is indicated by a the box. saltwater attach trim weight symbol. weights. Use tail strap when: • Operating Trident in strong current such as openocean. • Using tether to raise or lowerTrident, such as from a dock or largeboat. Before dive: • It is recommendedt o update both the OpenROV App and Trident firmware before you head out to the water. To do this connect the controller to the Internet and launch the OpenROV App. Follow the prompt to update . .Please referto manual for more details aboutupdating software. • We recommend doing the first dive in clearwater s uch as a pool or lake. This is so you can get a feel for piloting while being able to seeT rident. • Unrolla couple of metersof tether before and as needed throughout the dive. • Make sure the Topside and tether aresafely secured. It is importantt o keep the Topside close to you and easily retrievable. • Even though the Topside is water resistant, it is not designed to be submerged under water for long periods of time. During dive: • Avoid areas with high WiFi trafficto ensure uninterrupted Topside signal quality. • Don't drive the vehicle through seaweed or other vegetation as it can get stuck in the propellers. · • Avoid rocks, branches, or other objects that can potentially damage the vehicle or pose a risk for entanglement. • Avoid animals, fish, or other sensitive living things like corals which can be easily damaged. • Only keep the amount of tether you need in the water to avoid entanglement. After dive: • Rinse Trident withfresh waterafter ev erydive. • Be sureto keep tether plugged in while rinsing. • After rinsing, remove tether and dry connector areawith cloth or towel..