Technical Data Corterra® Solid Surface (Pdf)
Total Page:16
File Type:pdf, Size:1020Kb
CORTERRA® SOLID SURFACE MATERIAL Please visit www.acorneng.com for most current specifications. CORTERRA SOLID SURFACE PRODUCT DESCRIPTION Corterra® is a solid-surface polymer resin (with aluminum trihydrate and other fillers) and conforms with ANSI Z124.3, ANSI Z124.6, ICPA SS-1, IGC 156-2009, CSA B45.0-02, and CSA B45.5-02 requirements. Corterra® uses a minimum of 15% post- consumer recycled material and a minimum 5% rapidly renewable material derived from bio-based sources. Corterra® comes in several attractive color options to compliment surrounding decor. PRODUCT QUALITIES: l Crack-Resistant, durable, long-lasting material l Smooth, non-porous surface l Easy to clean and maintain l Chemical and stain resistant l Impact and scratch resistant, therefore deterring vandalism l A polymer resin application that contributes to LEED points l Resistant to heat and water damage, excellent thermal shock performance l 9 available colors allow for a more appealing, contemporary look l Content that is between 5% and 20% recycled material CLEANING TIPS: l Regular maintenance involves wiping the surface down with a soapy sponge and wiping dry with a clean cloth. l Stains caused by beverage or chemical spill can be removed by soaking a cloth in a mixture of soap and water. Then wipe agent over the affected area until clean. l Soapy water or any ammonia-based cleaners will remove most dirt and stains. l For stubborn stains try soaking affected area with mild household cleaner, such as Windex® or Lysol®, for approximately 10 minutes. Then rinse it with water and wipe with a Scotch Brite® pad. l To remove persistent stains use a Scotch-Brite® pad and an abrasive cleaner or a solution of household bleach and water (1 part water to 1 part bleach), do not let bleach soak in for more than two (2) minutes. l To remove dry or hardened particles, such as gum or food, by scraping use a putty knife or a blade. Be careful with blade or the putty knife because it can scratch the surface. l To make surface shine like “new” again, rub a polishing agent or even regular toothpaste. Using a polishing brush evenly polishes the surface. ANSI STANDARDS COMPLIANCE American National Standards Institute Z124.3 and Z124.6 applicable sections tested: PHYSICAL PROPERTIES AN SI TEST CORTERRA FIN DIN G S MA TERIA LS CO MPO SITIO N 2.1 CO MPLIES MA DE O F GRA DE PLA STIC RESIN CO LO RFA STN ESS (200 HO URS, A STM D2565-85) 5.1 CO MPLIES N O SIGN IFICA N T CHA N GE IN CO LO R STA IN RESISTA N CE 5.2 CO MPLIES N O MA TERIA L LO SS W EA R A N D CLEA N A BILITY (10,000 CYCLES) 5.3 CO MPLIES LESS THA N 2% W HITE LIGHT REFLECTIV EN ESS LO ST CIGA RETTE BURN RESISTA N CE 5.4 CO MPLIES DA MA GE DID N O T IMPA IR SERV ICEA BILITY, EA SILY REPA IRA BLE CHEMICA L RESISTA N CE 5.5 CO MPLIES DA MA GE DID N O T IMPA IR SERV ICEA BILITY, EA SILY REPA IRA BLE HEA TED PA N (3 A PPLICA TIO N S A T 365° F) 5.6 CO MPLIES N O SIGN S O F CRA CKIN G, CRA ZIN G, O R BLISTERIN G HO T W A X (10 O Z., 365° F) 5.7 CO MPLIES N O SIGN S O F CRA CKIN G, CRA ZIN G, O R DISCO LO RA TIO N CSA STANDARDS COMPLIANCE Canadian Standards Association B45.0-02 and B45.5-02 applicable sections tested: P HY SIC A L P RO P ERTIES C SA TEST C O RTERRA FIN DIN G S M A TERIA LS 4.1 C O M P LIES A LL M A TERIA LS W ERE FREE FRO M D EFIC IEN C IES THERM A L TEST 4.2 C O M P LIES N O BLISTERIN G, C HA N GE IN FIBRE P RO M IN EN C E, O R C RA C K IN G W A TER A BSO RP TIO N 4.3 C O M P LIES N O T A P P LIC A BLE C O LO RFA STN ESS 4.4 C O M P LIES N O SIGN IFIC A N T C HA N GE IN C O LO R STA IN RESISTA N C E 4.5 C O M P LIES RESISTA N C E RA TIN G W A S 66 O UT O F 150 C LEA N A BILITY A N D W EA R 4.6 C O M P LIES LESS THA N 2% O F W HITE LIGHT C HA N GE D ELA M IN A TIO N 4.7 C O M P LIES N O T APPLIC AB LE RESISTA N C E TO C IGA RETTE BUM S 4.8 C O M P LIES A LL SU R FA CE S R E T U R N E D T O AN A CCE PT A B LE FIN ISH B Y PO L ISH I N G . IGN ITA BILITY O F UN EX P O SED SURFA C E 4.9 C O M P LIES N O T A P P LIC A BLE BURNING CHARACTERISTICS TEST: FIRE RESISTANCE TESTING TEST RESULT TEST METHOD FIRE RESISTANCE, FLAME & SMOKE CLASS 1 CAN/ULC-S102-07 FIRE RESISTANCE, FLAME & SMOKE (CAN) FSR = 5, SDC = 137 CAN/ULC-S102-07 Complies with the following standards: ACORN ENGINEERING FIELD SERVICE TOLL FREE 800-743-8259 • LOCAL 626-855-4866 • FAX 626-855-4863 SOLID SURFACE SHEET Date: 06/13/14.