DOCSLIB.ORG

Chapter 1 Basic Radio Considerations

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Chapter 1 Basic Radio Considerations Source: Communications Receivers: DSP, Software Radios, and Design Chapter 1 Basic Radio Considerations 1.1 Radio Communications Systems The capability of radio waves to provide almost instantaneous distant communications without interconnecting wires was a major factor in the explosive growth of communica- tions during the 20th century. With the dawn of the 21st century, the future for communi- cations systems seems limitless. The invention of the vacuum tube made radio a practical and affordable communications medium. The replacement of vacuum tubes by transistors and integrated circuits allowed the development of a wealth of complex communications systems, which have become an integral part of our society. The development of digital signal processing (DSP) has added a new dimension to communications, enabling sophis- ticated, secure radio systems at affordable prices. In this book, we review the principles and design of modern single-channel radio receiv- ers for frequencies below approximately 3 GHz. While it is possible to design a receiver to meet specified requirements without knowing the system in which it is to be used, such ig- norance can prove time-consuming and costly when the inevitable need for design compro- mises arises. We strongly urge that the receiver designer take the time to understand thor- oughly the system and the operational environment in which the receiver is to be used. Here we can outline only a few of the wide variety of systems and environments in which radio re- ceivers may be used. Figure 1.1 is a simplified block diagram of a communications system that allows the transfer of information between a source where information is generated and a destination that requires it. In the systems with which we are concerned, the transmission medium is ra- dio, which is used when alternative media, such as light or electrical cable, are not techni- cally feasible or are uneconomical. Figure 1.1 represents the simplest kind of communica- tions system, where a single source transmits to a single destination. Such a system is often referred to as a simplex system. When two such links are used, the second sending informa- tion from the destination location to the source location, the system is referred to as duplex. Such a system may be used for two-way communication or, in some cases, simply to provide information on the quality of received information to the source. If only one transmitter may transmit at a time, the system is said to be half-duplex. Figure 1.2 is a diagram representing the simplex and duplex circuits, where a single block T represents all of the information functions at the source end of the link and a single block R represents those at the destination end of the link. In this simple diagram, we encounter one of the problems which arise in communications systems—a definition of the boundaries be- tween parts of the system. The blocks T and R, which might be thought of as transmitter and receiver, incorporate several functions that were portrayed separately in Figure 1.1. 1 Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright © 2004 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Basic Radio Considerations 2 Communications Receivers Figure 1.1 Simplified block diagram of a communications link. Figure 1.2 Simplified portrayal of communi- cations links: (a) simplex link, (b) duplex link. Many radio communications systems are much more complex than the simplex and du- plex links shown in Figures 1.1 and 1.2. For example, a broadcast system has a star configu- ration in which one transmitter sends to many receivers. A data-collection network may be organized into a star where there are one receiver and many transmitters. These configura- tions are indicated in Figure 1.3. A consequence of a star system is that the peripheral ele- ments, insofar as technically feasible, are made as simple as possible, and any necessary complexity is concentrated in the central element. Examples of the transmitter-centered star are the familiar amplitude-modulated (AM), frequency-modulated (FM), and television broadcast systems. In these systems, high-power transmitters with large antenna configurations are employed at the transmitter, whereas most receivers use simple antennas and are themselves relatively simple. An example of the receiver-centered star is a weather-data-collection network, with many unattended measur- ing stations that send data at regular intervals to a central receiving site. Star networks can be configured using duplex rather than simplex links, if this proves desirable. Mobile radio net- works have been configured largely in this manner, with the shorter-range mobile sets trans- mitting to a central radio relay located for wide coverage. Cellular radio systems incorporate a number of low-power relay stations that provide contiguous coverage over a large area, communicating with low-power mobile units. The relays are interconnected by various means to a central switch. This system uses far less spectrum than conventional mobile sys- tems because of the capability for reuse of frequencies in noncontiguous cells. Packet radio transmission is another example of a duplex star network. Stations transmit at random times to a central computer terminal and receive responses sent from the com- Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright © 2004 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Basic Radio Considerations Basic Radio Considerations 3 Figure 1.3 Star-type communications networks: (a) broadcast system, (b) data-collection network. puter. The communications consist of brief bursts of data, sent asynchronously and contain- ing the necessary address information to be properly directed. The term packet network is applied to this scheme and related schemes using similar protocols. A packet system typi- cally incorporates many radios, which can serve either as terminals or as relays, and uses a flooding-type transmission scheme. The most complex system configuration occurs when there are many stations, each hav- ing both a transmitter and receiver, and where any station can transmit to one or more other stations simultaneously. In some networks, only one station transmits at a time. One may be designated as a network controller to maintain a calling discipline. In other cases, it is neces- sary to design a system where more than one station can transmit simultaneously to one or more other stations. In many radio communications systems, the range of transmissions, because of terrain or technology restrictions, is not adequate to bridge the gap between potential stations. In such a case, radio repeaters can be used to extend the range. The repeater comprises a receiving system connected to a transmitting system, so that a series of radio links may be established to achieve the required range. Prime examples are the multichannel radio relay system used by long-distance telephone companies and the satellite multichannel relay systems that are used extensively to distribute voice, video, and data signals over a wide geographic area. Satellite relay systems are essential where physical features of the earth (oceans, high moun- tains, and other physical restrictions) preclude direct surface relay. On a link-for-link basis, radio relay systems tend to require a much higher investment than direct (wired) links, depending on the terrain being covered and the distances involved. To make them economically sound, it is common practice in the telecommunications indus- try to multiplex many single communications onto one radio relay link. Typically, hundreds of channels are sent over one link. The radio links connect between central offices in large population centers and gather the various users together through switching systems. The hundreds of trunks destined for a particular remote central office are multiplexed together into one wider-bandwidth channel and provided as input to the radio transmitter. At the other central office, the wide-band channel is demultiplexed into the individual channels and distributed appropriately by the switching system. Telephoneand data common carriers are probably the largest users of such duplex radio transmission. The block diagram of Fig- Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright © 2004 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Basic Radio Considerations 4 Communications Receivers Figure 1.4 Block diagram of simplified radio relay functions: (a) terminal transmitter, (b)re- peater (without drop or insert capabilities), (c) terminal receiver. ure 1.4 shows the functions that must be performed in a radio relay system. At the receiving terminal, the radio signal is intercepted by an antenna, amplified and changed in frequency, demodulated, and demultiplexed so that it can be distributed to the individual users. In addition to the simple communications use of radio receivers outlined here, there are many special-purpose systems that also require radio receivers. While the principles of de- sign are essentially the same, such receivers have peculiarities that have led to their own de- sign specialties. For example, in receivers used for direction finding, the antenna systems have specified directional patterns. The receivers must accept one or more inputs and pro- cess them so that the output signal can indicate the direction from which the signal arrived. Older techniques include the use of loop antennas, crossed loops, Adcock antennas, and other specialized designs, and determine the direction from a pattern null. More modern Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright © 2004 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Basic Radio Considerations Basic Radio Considerations 5 systems use complex antennas, such as the Wullenweber.
Load more

Recommended publications
  • US2959674.Pdf
    Nov. 8, 1960 T. R. O "MEARA 2,959,674 GAIN CONTROL FOR PHASE AND GAIN MATCHED MULTI-CHANNEL RADIO RECEIVERS Filed July 2, 1957 2. Sheets-Sheet 2 PETARD CONVERTER TUBE Ë????Q. F SiGNAL OUTPUT OSC. S. G. INPUT INVENTOR. 77/OMAS A. O’MEAAA AT 7OAPWA 3 2,959,674 United States Patent Office Patented Nov. 8, 1960 1. 2 linear type. By a linear type frequency changer is meant a device with output current or voltage which is a linear 2.959,674 function of either the RF input signal or local oscillator GAIN CONTROL FOR PHASE AND GAN signal alone and with a conversion transconductance MATCHED MULT-CHANNELRADIO RE. 5 characteristic which varies linearly with the magnitude of CEIVERS the voltage at the local oscillator input to the device. Thomas R. O'Meara, Los Angeles, Calif., assignor, by This means that, if instead of being an alternating voltage, meSne assignments, to the United States of America as the RF signal input to the device were maintained at a represented by the Secretary of the Navy constant D.C. voltage and the oscillator signal were re 0. placed by a D.C. voltage excursion, then a plot of the Filed July 2, 1957, Ser. No. 669,691 output current or voltage of the device versus the local oscillator signal voltage would be a straight line. Simi 3 Claims. (Cl. 250-20) larly, if the local oscillator signal voltage input to the device were kept at a constant D.C. value, instead of This invention relates to a gain control for electronic 5 being an A.C.
    [Show full text]
  • Suitability of a Commercial Software Defined Radio System for Passive Coherent Location
    Suitability of a Commercial Software Defined Radio System for Passive Coherent Location Aadil Volkwin A dissertation submitted to the Department of Electrical Engineering, University of Cape Town, in fulfilment of the requirements for the degree of Master of Science in Engineering. Cape Town, May 2008 Dedicated to: My Parents, my Sister and my Wife. 2 Declaration I declare that this work done is my own, unaided work. This dissertation is being submitted to the Department of Electrical Engineering, University of Cape Town, in fulfilment of the requirements for the degree of Master of Science in Engineering. It has not been submitted for any degree or examination in any other university. ................................................................................ Signature of Author Cape Town 2008 3 Abstract This dissertation provides a comprehensive discussion around bistatic radar with specific reference to PCL, highlighting existing literature and work, examining the various performance metrics. In particular the performance of commercial FM radio broadcasts as the radar waveform is examined by implementation of the ambiguity function. The FM signals show desirable characteristics in the context of our application, the average range resolution obtained is 5.98km, with range and doppler peak sidelobe levels measured at -25.98dB and -33.14dB respectively. Furthermore, the SDR paradigm and technology is examined, with discussion around the design considerations. The USRP, the TVRx daughterboard and GNURadio are examined further as a potential receiver and development environment, in this light. The system meets the low cost ambitions costing just over US$1000.00 for the USRP motherboard and a single daughterboard. Furthermore it performs well, displaying desirable characteristics, The receiver's frontend provides a bandwidth of 6MHz and a tunable range between 50MHz and 800MHz, with a tuning step size as low as 31.25kHz.
    [Show full text]
  • Maintenance of Remote Communication Facility (Rcf)
    ORDER rlll,, J MAINTENANCE OF REMOTE commucf~TIoN FACILITY (RCF) EQUIPMENTS OCTOBER 16, 1989 U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION AbMINISTRATION Distribution: Selected Airway Facilities Field Initiated By: ASM- 156 and Regional Offices, ZAF-600 10/16/89 6580.5 FOREWORD 1. PURPOSE. direction authorized by the Systems Maintenance Service. This handbook provides guidance and prescribes techni- Referenceslocated in the chapters of this handbook entitled cal standardsand tolerances,and proceduresapplicable to the Standardsand Tolerances,Periodic Maintenance, and Main- maintenance and inspection of remote communication tenance Procedures shall indicate to the user whether this facility (RCF) equipment. It also provides information on handbook and/or the equipment instruction books shall be special methodsand techniquesthat will enablemaintenance consulted for a particular standard,key inspection element or personnel to achieve optimum performancefrom the equip- performance parameter, performance check, maintenance ment. This information augmentsinformation available in in- task, or maintenanceprocedure. struction books and other handbooks, and complements b. Order 6032.1A, Modifications to Ground Facilities, Order 6000.15A, General Maintenance Handbook for Air- Systems,and Equipment in the National Airspace System, way Facilities. contains comprehensivepolicy and direction concerning the development, authorization, implementation, and recording 2. DISTRIBUTION. of modifications to facilities, systems,andequipment in com- This directive is distributed to selectedoffices and services missioned status. It supersedesall instructions published in within Washington headquarters,the FAA Technical Center, earlier editions of maintenance technical handbooksand re- the Mike Monroney Aeronautical Center, regional Airway lated directives . Facilities divisions, and Airway Facilities field offices having the following facilities/equipment: AFSS, ARTCC, ATCT, 6. FORMS LISTING. EARTS, FSS, MAPS, RAPCO, TRACO, IFST, RCAG, RCO, RTR, and SSO.
    [Show full text]
  • Front-End Receiver: Recent and Emerging Trend Ulrich L
    Front-End Receiver: Recent and Emerging Trend Ulrich L. Rohde Ajay K. Poddar Enrico Rubiola Marius A. Silaghi BTU Cottbus 03046 Germany Synergy Microwave NJ USA FEMTO-ST Inst. Besancon France University of Oradea, Romania Abstract—This paper describes the recent trend of front-end receiver systems for the application in radio monitoring. The 650 MHz to 1300 MHz receiver implementation is optimized for applications such as 20 MHz to 650 MHz hunting and detecting unknown signals, identifying interference, Vin =−117 dBm (0.3 μV) ≥10 dB Vin=−47 dBm (1 mV) ≥50 dB spectrum monitoring and clearance, and signal search over wide LSB/USB, IF bandwidth 500 frequency ranges, producing signal content and direction finding Hz, of identified signals. Δf=500 Hz 0.5 MHz to 20 MHz, ≥10 dB Keywords—Receivers, Real time FFT Processing Vin=0.4μV 20 to 30 MHz, Vin= 0.5 μV ≥10 dB I. INTRODUCTION LSB/USB, IF bandwidth The emerging security threats demand an intensive data 2.5kHz, Δf=1kHz gathering for fiber or radio communication [1]. Besides the 0.5 MHz to 20 MHz, ≥10 dB fiber technology, there are varieties of wireless activities, Vin=0.6μV which are typically analyzed by off the air monitoring [2]-[9]. 20 to 30 MHz, Vin= 0.7 μV ≥10 dB The spectral density of signals these days is very high and Vin= 100 μV ≥46 dB therefore such monitoring receivers require high performance. AM, IF Bandwidth 2.5kHz, The technique in designing such receivers is a composition of fmod=1 kHz, m=0.5 0.5 MHz to 20 MHz, ≥10 dB microwave engineering of the building blocks preamplifier, Vin=1μV mixer, synthesizer and necessary filters, this paper describes 20 to 30 MHz, Vin= 1.2 μV ≥10 dB critical aspects of important building blocks of radio Crossmodulation interfering monitoring receives [10]-[20].
    [Show full text]
  • Master's Thesis
    Eindhoven University of Technology MASTER Mapping a China Digital Radio (CDR) receiver on a software-defined-radio platform Cheng, Y. Award date: 2017 Link to publication Disclaimer This document contains a student thesis (bachelor's or master's), as authored by a student at Eindhoven University of Technology. Student theses are made available in the TU/e repository upon obtaining the required degree. The grade received is not published on the document as presented in the repository. The required complexity or quality of research of student theses may vary by program, and the required minimum study period may vary in duration. General rights Copyright and moral rights for the publications made accessible in the public portal are retained by the authors and/or other copyright owners and it is a condition of accessing publications that users recognise and abide by the legal requirements associated with these rights. • Users may download and print one copy of any publication from the public portal for the purpose of private study or research. • You may not further distribute the material or use it for any profit-making activity or commercial gain Department of Mathematics and Computer Science Algorithm & Software Innovation Mapping a China Digital Radio (CDR) receiver on a Software-Defined-Radio platform Master Thesis Yan Cheng Supervisors: prof.dr.ir.C.H.(Kees) van Berkel Dr.Hong Li Eindhoven, August 2017 Abstract With the launch of the China Digital Radio (CDR) standard in hundreds of cities in China, CDR radio receiver chips are required in market. To explore fast and efficient embedded Software- Defined-Radio (SDR) CDR receiver design and realization, this thesis project used Data-Flow (DF) modeling to study architectural options of a CDR receiver design for an existing NXP SDR chip.
    [Show full text]
  • Multiband LNA Design and RF-Sampling Front-Ends for Flexible Wireless Receivers
    Linköping Studies in Science and Technology Dissertation No. 1036 Multiband LNA Design and RF-Sampling Front-Ends for Flexible Wireless Receivers Stefan Andersson Electronic Devices Department of Electrical Engineering Linköping University, SE-581 83 Linköping, Sweden Linköping 2006 ISBN 91-85523-22-4 ISSN 0345-7524 ii Multiband LNA Design and RF-Sampling Front-Ends for Flexible Wireless Receivers Stefan Andersson ISBN 91-85523-22-4 Copyright c Stefan Andersson, 2006 Linköping Studies in Science and Technology Dissertation No. 1036 ISSN 0345-7524 Electronic Devices Department of Electrical Engineering Linköping University SE-581 83 Linköping Sweden Author e-mail: [email protected] Cover Image Picture by the author illustrating an RF-sampling receiver on block level. The chip microphotograph represents a multiband direct RF-sampling receiver front-end for WLAN fabricated in 0.13 µm CMOS. Printed by LiU-Tryck, Linköping University Linköping, Sweden, 2006 I nådens år 2006! As my grandfather would have said. iii iv Abstract The wireless market is developing very fast today with a steadily increasing num- ber of users all around the world. An increasing number of users and the constant need for higher and higher data rates have led to an increasing number of emerging wireless communication standards. As a result there is a huge demand for flexible and low-cost radio architectures for portable applications. Moving towards multi- standard radio, a high level of integration becomes a necessity and can only be ac- complished by new improved radio architectures and full utilization of technology scaling. Modern nanometer CMOS technologies have the required performance for making high-performance RF circuits together with advanced digital signal processing.
    [Show full text]
  • Chapter 2 Radio Receiver Characteristics
    Source: Communications Receivers: DSP, Software Radios, and Design Chapter 1 Basic Radio Considerations 1.1 Radio Communications Systems The capability of radio waves to provide almost instantaneous distant communications without interconnecting wires was a major factor in the explosive growth of communica- tions during the 20th century. With the dawn of the 21st century, the future for communi- cations systems seems limitless. The invention of the vacuum tube made radio a practical and affordable communications medium. The replacement of vacuum tubes by transistors and integrated circuits allowed the development of a wealth of complex communications systems, which have become an integral part of our society. The development of digital signal processing (DSP) has added a new dimension to communications, enabling sophis- ticated, secure radio systems at affordable prices. In this book, we review the principles and design of modern single-channel radio receiv- ers for frequencies below approximately 3 GHz. While it is possible to design a receiver to meet specified requirements without knowing the system in which it is to be used, such ig- norance can prove time-consuming and costly when the inevitable need for design compro- mises arises. We strongly urge that the receiver designer take the time to understand thor- oughly the system and the operational environment in which the receiver is to be used. Here we can outline only a few of the wide variety of systems and environments in which radio re- ceivers may be used. Figure 1.1 is a simplified block diagram of a communications system that allows the transfer of information between a source where information is generated and a destination that requires it.
    [Show full text]
  • Task 3 Tompkins County
    q NYS TEC New York State Technology Enterprise Corporation presents its Options for a Public Safety Wireless Communications System: Synthesis and Evaluation Report for the Tompkins County Radio System Project February 28, 2001 Version 2 Options for a Public Safety Wireless Radio Communication System: NYS TEC Synthesis and Evaluation Report Tompkins County Radio System Project Table of Contents 1. OVERVIEW ..................................................................................................................................................1 2. WIDE-AREA WIRELESS MOBILE TECHNOLOGY ............................................................................3 2.1 RADIO FREQUENCIES .......................................................................................................................................3 2.2 CONVENTIONAL RADIO SYSTEMS ..................................................................................................................10 2.3 DIGITAL VOICE, DATA AND ENCRYPTION......................................................................................................13 2.4 VOTING SYSTEMS ..........................................................................................................................................17 2.5 TRUNKED RADIO SYSTEMS ............................................................................................................................17 2.6 SIMULCAST ....................................................................................................................................................24
    [Show full text]
  • Radio Receiver Design
    Radio Receiver Design Robert C. Dixon MARCEL DEKKER, INC. Radio Receiver Design ELECTRICAL ENGINEERING AND ELECTRONICS ,4 Series of Reference Books and Textbooks EXECUTIVE EDITORS Marlin 0. Thurston William Midendorf Department of Electrical Engineering Department of Electrical The Ohio State University and Computer Engineering Columbus, Ohio University of Cincinnati Cincinnati. Ohio EDITORIAL BOARD Maurice Bellanger Nairn A. Kheir TClCcommunications, RadioClectriques, Department of Electrical and et TClCphoniques (TRT) Systems Engineering Le Plessis-Robinson, France Oakland University Rochester, Michigan Norman B. Fuqua Reliability Analysis Center Pradeep Khosla Griffiss Air Force Base, New York Carnegie-Mellon University Pittsburgh, Pennsylvania Glenn Zelniker Z-Systems, Inc. Gainesville, Florida 1. Rational Fault Analysis, edited by Richard Saeks and S. R. Liberty 2. Nonparametric Methods in Communications, edited by P. Papantoni- Kazakos and Dimitri Kazakos 3. Interactive Pattern Recognition, Yi-tzuu Chien 4. Solid-state Electronics, Lawrence E. Murr 5. Electronic, Magnetic, and Thermal Properties of Solid Materials, Klaus Schroder 6. Mag netic- Bu b bl e Memory Tec hno1 og y , Hsu Chang 7. Transformer and lnductor Design Handbook, Colonel Wm. T. McL yman 8. Electromagnetics: Classical and Modern Theory and Applications, Samuel Seely and Alexander 0.Poularikas 9. One-Dimensional Digital Signal Processing, Chi- Tsung Chen 10. Interconnected Dynamical Systems, Raymond A. DeCarlo and Richard Saeks 11 Modern Digital Control Systems, Raymond G. Jacquot 12. Hybrid Circuit Design and Manufacture, Roydn D. Jones 13. Magnetic Core Selection for Transformers and Inductors: A User's Guide to Practice and Specification, Colonel Wm. T. McLyman 1 4. Static ar\d Rotating Electromagnetic Devices, Richard H. Engelmann 1 5.
    [Show full text]
  • Microwave Radio Transmission Design Guide
    Microwave Radio Transmission Design Guide Second Edition page i Finals 06-17-09 10:39:14 For a listing of recent titles in the Artech House Microwave Library, turn to the back of this book. page ii Finals 06-17-09 10:39:14 Microwave Radio Transmission Design Guide Second Edition Trevor Manning page iii Finals 06-17-09 10:39:14 Library of Congress Cataloging-in-Publication Data A catalog record for this book is available from the U.S. Library of Congress. British Library Cataloguing in Publication Data A catalogue record for this book is available from the British Library. ISBN-13: 978-1-59693-456-6 Cover design by Igor Valdman 2009 ARTECH HOUSE 685 Canton Street Norwood, MA 02062 All rights reserved. Printed and bound in the United States of America. No part of this book may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without permission in writing from the publisher. All terms mentioned in this book that are known to be trademarks or service marks have been appropriately capitalized. Artech House cannot attest to the accuracy of this information. Use of a term in this book should not be regarded as affecting the validity of any trademark or service mark. 10 987654321 page iv Finals 06-17-09 10:39:14 Contents Foreword xiii Preface xv 1 Introduction 1 1.1 History of Wireless Telecommunications 2 1.2 What Is Microwave Radio? 3 1.2.1 Microwave Fundamentals 3 1.2.2 RF Spectrum 4 1.2.3 Safety of Microwaves 5 1.2.4 Allocation
    [Show full text]
  • Houston Fire Department
    CITY OF HOUSTON, TX TRUNKED RADIO SYSTEM REQUEST FOR PROPOSALS, 8/31/07 Section 1—Current Radio Communications Environment... 1 1.1 Houston Airport System.........................................................................................1 1.1.1 Current Operations...................................................................................1 1.1.2 Radio System Coverage............................................................................1 1.1.3 Dispatch Operations .................................................................................2 1.1.4 Needs & Requirements.............................................................................5 1.1.5 Interoperability Needs ..............................................................................6 1.2 Houston Fire Department ......................................................................................6 1.2.1 Current Operations...................................................................................6 1.2.2 User Equipment .......................................................................................7 1.2.3 Dispatch Operations .................................................................................8 1.2.4 Radio System Problems ..........................................................................16 1.2.5 Needs & Requirements...........................................................................17 1.2.6 Functional Requirements ........................................................................19 1.3 Houston Police Department
    [Show full text]
  • ATS-6 Final Engineering Performance Report
    NASA ,-.:1NASA-RP-1080-VOL-5 Reference 19820008278 Publication 1080 _"_:-__'_,_:__, c_,_,_ t c_,_, r,', . _!,.,., .,,, ._, ;,,".:2,', J4"7;_r.-_: ',,,:z :_, ^, November 1981 ' " -........._'_' ATS-6 Final Engineering Performance Report Volume V - Propagation Experiments NI A NASA Reference Publication 1080 1981 ATS-6 Final Engineering Performance Report Volume V- Propagation.Experiments Robert O. Wales, Editor Goddard Space Flight Center Greenbelt, Maryland NI A National Aeronautics and Space Administration Scientific and Technical Information Branch An EngineeringEvaluation in Six Volumes Volume I: Programand System Summaries;Mechanical and Thermal Details Part A: Program Summary Part B: Mechanical Subsystems Part C: Thermal Control and Contamination Monitor Volume II: Orbit and Attitude Controls Part A: Attitude Control Part B: Pointing Experiments Part C: Spacecraft Propulsion Part D: Propulsion Experiment Volume III: Telecommunications and Power Part A: Communications Subsystem Part B: Electrical Power Subsystem Part C: Telemetry and Command Subsystem Part D: Data Relay Experiments Volume IV: Television Experiments Part A: The Department of Health, Education and WelfareSponsored Experiments Part B: Satellite Instructional TelevisionExperiment (India) Part C: Independent TelevisionExperiments Volume V: Propagation Experiments Part A: Experiments at 1550 MHz to 1650 MHz Part B: Experiments at 4 GHz to 6 GHz Part C: Experiments Above 10GHz Volume VI: Scientific Experiments This document makes use of international metric units according to the Syst_me International d'Unit_s (SI). In certain cases, utility requires the retention of other systems of units in addition to the SI units. The conven- tional units stated in parentheses following the computed SI equivalents are the basis of the measurements and calculations reported.
    [Show full text]