W4100D User Manual (English)
Total Page:16
File Type:pdf, Size:1020Kb
CONNECTING THE POWER CABLE PAGE 1 CONNECTING THE MONITOR PAGE 1 TRACKMAN MOUSE PAGE 2 AF-IN, HF-IN AND IF-IN PAGE 2 PROGRAMME DISK PAGE 3 DIP-SWITCH SETUP PAGE 4 PC/AT HOST INTERFACE PAGE 5 EXTERNAL DEMODULATOR PAGE 5 455 KHZ, 10.7 MHZ AND 21.4 MHZ INPUTS PAGE 5 PCM-IN INPUT PAGE 5 DIGITAL-IN INPUT PAGE 6 AF-OUT OUTPUT PAGE 6 SERIAL INTERFACES RS232 #1 AND RS232 #2 PAGE 7 CONNECTING A SERIAL PRINTER PAGE 8 CONNECTING A PC/AT PAGE 8 CONNECTING A CENTRONICS PRINTER PAGE 9 CONNECTOR PIN-OUT VGA-MONITOR PAGE 10 CONNECTOR PIN-OUT TRACKMAN MOUSE PAGE 10 CONNECTOR PIN-OUT PC/AT HOST INTERFACE PAGE 11 CONNECTOR PIN-OUT EXTERNAL DEMODULATOR PAGE 11 CONNECTOR PIN-OUT SERIAL RS232 #1 AND REMOTE CONTOL PAGE 12 CONNECTOR PIN-OUT CENTRONICS PRINTER PAGE 12 CONNECTOR PIN-OUT DIGITAL IN PAGE 13 CONNECTOR PIN-OUT PCM IN PAGE 13 TECHNICAL DATA OF THE VGA VIDEO INTERFACE PAGE 14 TRACKMAN MOUSE FUNCTION PAGE 1 CURSOR KEY FUNCTION PAGE 1 USER INTERFACE PAGE 2 STANDARD MENU PAGE 3 DEMODULATOR FIELD PAGE 3 FULL SCREEN MENU PAGE 4 DEMODULATOR WINDOW PAGE 5 FEATURES OF THE DSP DEMODULATOR PAGE 6 DEMODULATOR MENU PAGE 8 OPTIONS MENU PAGE 11 FRONT PANEL COMPONENTS PAGE 13 TUNING RADIO DATA SIGNALS PAGE 15 FUNDAMENTALS OF TELEGRAPH TRANSMISSIONS PAGE 19 DUPLEX MODES HF PAGE 25 SIMPLEX MODES HF PAGE 26 FEC MODES HF PAGE 27 CONTENTS - PAGE 2 MFSK MODES HF PAGE 28 VHF/UHF DIRECT MODES PAGE 29 VHF/UHF INDIREC MODES PAGE 30 FAX MODES PAGE 31 CARRIER MODULATION PROCEDURES PAGE 32 BAUDRATES, SPEED AND CARRIER MODULATION PAGE 33 VIDEO FULL SCREEN MENU PAGE 1 MAIN MENU PAGE 2 MODES FROM A TO Z PAGE 3-91 A ACARS, ALIS, ALIS-2, ARQ-E, ARQ-E3, ARQ-N, ARQ-M2-242, ARQ-M2-342, ARQ-M4-242, ARQ-M4-342 ARQ6-90, ARQ6-98, ASCII, ATIS, AUTOSPEC B BAUDOT, BULG-ASCII C CCIR, CCITT, CIS-11, CIS-14, CIS-36, CODAN SELCAL, COQUELET-8, CO- QUELET-13, QUOQUELET-80, CW-MORSE D DGPS, DUP-ARQ, DUP-ARQ-2, DUP-FEC-2, DTMF E ERMES, EEA, EIA, EURO F FEC-A, FELDHELL, FMS-BOS G GMDSS/DSC-HF AND VHF, GOLAY, G-TOR H HC-ARQ, HNG-FEC I ICAO SELCAL, INFOCALL M METEOSAT, MPT1327 N NATEL, NOAA-GEOSAT P PACTOR, PACKET-300/600, PACKET-1200, PACKET-9600, PCM-30, PICCOLO- MK6, PICCOLO-MK12 POCSAG, POL-ARQ, PRESS- FAX, PSK-31 R RUM-FEC S SELCAL ANALOG, SI-ARQ, SI-FEC, SI-AUTO, SITOR-ARQ, SITOR-FEC, SITOR- AUTO, SPREAD-11, SPREAD-21, SPREAD-51, SSTV, SWED-ARQ T TWINPLEX v VDEW W WEATHER-FAX Z ZVEI-VDEW, ZVEI-1, ZVEI-2 MENU ANALYSIS HF PAGE 1 MENU ANALYSIS VHF PAGE 1 MENU SIGNAL ANALYSIS HF PAGE 2 MENU SIGNAL ANALYSIS VHF/UHF PAGE 2 FSK ANALYSIS HF PAGE 2 SIGNAL TWINPLEX PAGE 3 DIRECT FSK ANALYSIS VHF/UHF PAGE 4 INDIRECT FSK ANALYSIS VHF/UHF PAGE 6 PSK SYMBOL RATE MEASUREMENT AND PSK PHASE PLANE PAGE 8 HF CODE ANALYSIS PAGE 12 DIRECT CODE ANALYSIS VHF/UHF PAGE 15 INDIRECT CODE ANALYSIS VHF/UHF PAGE 18 VHF/UHF SELCAL ANALYSIS PAGE 20 HF MFSK ANALYSIS PAGE 22 REAL-TIME FFT PAGE 24 REAL-TIME-WATERFALL PAGE 27 CONTENTS - PAGE 3 REAL-TIME-SONAGRAM PAGE 28 REAL-TIME-OSCILLOSCOPE PAGE 29 AUTOCORRELATION PAGE 31 HF BIT ANALYSIS PAGE 34 BIT LENGTH ANALYSIS HF PAGE 39 RAW V1-DATA ANALYSIS HF PAGE 42 CODE STATISTICS HF PAGE 44 SETUP FUNCTIONS PAGE 46 REMOTE CONTROL PAGE 48 REMOTE-CONTROL EXAMPLES PAGE 50 GLOBAL REMOTE COMMANDS PAGE 52 SHORT COMMANDS PAGE 53 REMOTE COMMANDS MODES PAGE 54 LOADING OF THE W4100DSP SOFTWARE VIA REMOTE-CONTROL PAGE 63 TECHNICAL SPECIFICATIONS HARDWARE PAGE 1 VIDEO - DEMODULATOR - INTERFACES PAGE 2 TECHNICAL DATA DSP DEMODULATOR PAGE 4 SOFTWARE HF MODES PAGE 6 HF SIGNAL AND DATA ANALYSIS PAGE 12 SOFTWARE VHF/UHF MODES PAGE 14 VHF/UHF SIGNAL AND DATA ANALYSIS PAGE 16 ALPHABETS - PRINTER DRIVERS PAGE 18 TELEPRINTER ALPHABETS PAGE 19 TROUBLESHOOTING PAGE 21 FUSE REPLACEMENT PAGE 23 SIGNAL INTERFERENCES PAGE 23 CONDITIONS OF SALE PAGE 24 TERMS OF DELIVERY AND PRICES PAGE 25 LITERATURE PAGE 25 INSTALLATION - PAGE 1 Before connecting any peripheral heavy static build-ups. Because equipment to the data and tele- of this the metal case of the graph analyzer W4100DSP all de- W4100DSP which is grounded vices should be powered off to through the power mains should avoid damages. Experience shows be touched before installation that damage often occurs due to of any peripheral equipment. Connect the included power cable the upper part of the combined to a 230V/50Hz power mains out- mains connector and power on-off let and to the plug marked "AC switch. The W4100DSP is also 230 VOLT 50/60 Hz". A 1A mains available in a 115 Volts version fuse is located in a drawer in with a 2A mains fuse. Connect a VGA or multi sync The VGA video signal of the colour monitor to the rear DB-15 W4100DSP is compatible with PC- plug marked "VGA MONITOR". A ATs having a resolution of 640 x matching cable is included in 480 pixels. The red, green and the complete monitor package. If blue color signals are analog. an older type EGA plug is used, Please notice the paragraph an adapter (DB-9 female to DB-15 "Setting of the DIP switches" of male) may be obtained in most this section, where the computer stores. selection of H-sync and V-sync polarity is explained. Practically any monitor may be adapted to the interface. Some PHILIPS and EIZO monitors Several brands of monitors have have been tested. These models been tested. comply to the MPR II or TCO-92 radiation standard. INSTALLATION - PAGE 2 The A4 TrackMan Mouse included will then appear with a light in the complete W4100DSP pack- blue border. Pressing the left- age, is connected to the rear hand trackball key will activate DB-9 plug marked "TRACKMAN". The the selected function. This is switch on the right side of the equal to a keypad ENTER func- mouse must be set in position tion. Pressing the right hand "3" , e.g. PC-mode or LogiTech trackball key will deactivate data format. Position "2" corre- the selected function or take sponds to the Microsoft data you back to the preceding menu. format. This format is not util- ized with the W4100DSP. Pressing the lower left track- ball key twice quickly will pop- The plug is pinned as a stan- up a full screen menu. A more dard, serial RS-232 interface. in-depth description of the op- eration of the trackball may be The desired menu field is se- found in the "INTRODUCTION" sec- lected by moving the ball of the tion of this manual. trackball, the selected field Select Leave function function Full screen menu with double click Input to the various demodula- the receiver line output should tors of the W4100DSP is ob- always be used. Otherwise the tained via the input plugs phone or loudspeaker outputs marked "AF-IN", "AF/HF-IN", may be used. "455 KHZ IN", "10.7 MHZ IN" or "21.4 MHZ IN". An HF or IF out- All other inputs are designed put is common in professional for connection to IF outputs. receivers. Receivers equipped All inputs are equally suitable with an internal demodulator for the decoding of HF and VHF/ may be connected to the UHF modes. Detailed technical W4100DSP using the plug marked specifications of the inputs "EXTERN DEMODULATOR". The line may be found in the appendix or loudspeaker output of the "TECHNICAL SPECIFICATIONS". receiver is connected to the "AF-IN" inputs. If available The sensitivity of all inputs INSTALLATION - PAGE 3 is software selected using the inputs. In addition to the ana- "SETUP\GAIN" or the “DEMODU- log inputs the W4100DSP also has LATOR\GAIN" menu, which is in- a digital input which conforms cluded in all mode menus. The 0- to the RACAL data format 100 range corresponds to an in- ("DIGITAL IN"). The sensitivity put sensitivity of 0.01 Vpp to 5 of this input is fixed at 0 dB Vpp for maximum drive. so receiver output must be ad- justed to this level. The translation frequency is ad- justed by using the "SETUP FUNC- The front plate level indicator TIONS \ DEMODULATOR" menu or the ("LEVEL") indicates the input "DEMODULATOR \ TRANSLATION" menu signal level. When the red part included in most mode menus. The of the indicator is turned on, W4100DSP employs high stability the A/D converter is overloaded DDS frequency generation, the and the quality of the demodula- smallest step being 1 Hz on all tor output is decreased. Write-protect tab To load the W4100DSP software, will take about 8 1/2 minutes. place the enclosed 3 1/2" disk in the floppy drive. The file It is important that the disk format is PC-compatible and the write-protect tab always be files may be freely copied using placed in the write-protect po- any PC-AT 3 1/2" disk drive. The sition which is the case when MASTER.ARJ or APPLIK.GZ (for new both square holes of the rear boot-program version 4.2) file side of the disk are open. The contains the compressed data for disk may then remain in the disk the master processor, and the drive. If the tab is not in the LOADER.LOD, MASTER.LOD and write-protect position there is SLAVE.LOD files contain the a risk of destroying data when program for the two DSP proces- the W4100DSP is powered off.