DOCSLIB.ORG

Fast Ethernet Standlond Switch

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Fast Ethernet Standlond Switch DATASHEET www.edge-core.com ES3528M V2 L2 Fast Ethernet Standalone Switch Product Overview The Edge-Core ES3528MV2 is a Fast Ethernet Layer 2/4 switch featuring 28 ports; 24 100BASE-TX ports and 4 combination Gigabit Ethernet RJ-45/SFP (Small Form Factor Pluggable) ports. It is ideal for desktop Fast Ethernet connectivity and wiring closet installations. Using IP Clustering for a virtual stack of up to 36 switches, the whole stack can be managed as a single entity with a single IP address. This switch is packed with features and is a cost-effective solution that brings continuous availability, enhanced security and advanced QoS to the network edge, while maintaining simplicity of management. Fast Ethernet Standlond Switch Key Features and Benefits Performance and Scalability Enhanced Security With 12.8 Gbps switching capacity, the ES3528MV2 Port security allows access to switch ports based on delivers wire-speed switching performance on all MAC address, limits the total number of devices from Gigabit ports, allowing users to take full advantage of using a switch port, and protects against MAC flooding existing high-performance, Gigabit integrated servers, attacks. PCs and laptops by significantly improving the responsiveness of applications and file transfer times. IEEE 802.1X port-based or MAC-based access control ensures all users are authorized before being granted There are four Gigabit Ethernet combination ports for access to the network. User authentication is carried out uplink flexibility, allowing copper or fiber uplinks. The using any standard-based RADIUS server. switch also supports digital diagnostic monitoring (DDM) for SFP transceivers. Access Control Lists (ACLs) can be used to restrict access to sensitive network resources by denying Continuous Availability packets based on source and destination MAC IEEE 802.1w Rapid Spanning Tree Protocol provides a addresses, IP addresses, or TCP/UDP ports. ACLs are loop-free network and redundant links to the core hardware supported, so switching performance is not network with rapid convergence, to ensure faster compromised. recovery from failed links, enhancing overall network stability and reliability. Secure Shell (SSH) and Secure Sockets Layer (SSL/HTTPS) encrypts Telnet and web access to the IEEE 802.1s Multiple Spanning Tree Protocol runs STP switch, providing secure network management. per VLAN base, providing Layer 2 load sharing on redundant links. TACACS+/RADIUS authentication enables centralized control of the switch and prevents unauthorized users IEEE 802.3ad Link Aggregation Control Protocol (LACP) from altering the configuration of the switch. increases bandwidth by automatically aggregating several physical links together as a logical trunk and Private VLANs isolate edge ports to ensure user privacy. providing load balancing and fault tolerance for uplink connections. Simple Management An industry-standard Command Line Interface (CLI), IGMP snooping prevents flooding of IP multicast traffic accessed through the console port or Telnet, provides a and limits bandwidth intensive video traffic to only the convenient way to configure and troubleshoot the switch. subscribers. An embedded user-friendly web interface helps users quickly and simply configure the switch. Four-group Broadcast Storm Control prevents faulty end stations RMON is supported to collect traffic statistics and run from degrading overall system performance. network diagnostics. The switch can also backup and restore firmware and configuration files via TFTP. Comprehensive QoS Eight egress queues per port enable differentiated management of up to eight traffic types. Traffic is prioritized according to 802.1p and DSCP, giving optimal performance to real-time applications such as voice and video. Asymmetric bidirectional rate-limiting, per port or per traffic class, preserves network bandwidth and allows maximum control of network resources. For a world always connected… ES3528M V2 Product Specifications www.edge-core.com Features Physical Ports Management 24 100BASE-TX ports Switch Management: 4 Combo Gigabit (RJ-45/SFP) ports ■ CLI via console port or Telnet 1 RS-232 DB-9 console port ■ Web management ■ SNMP v1, v2c, v3 Performance Firmware and Configuration: Switching Capability: 12.8 Gbps ■ Dual firmware images Packet Buffer Size: 4 Mbits ■ Firmware upgrade via TFTP server MAC Address Table: 16K ■ Multiple configuration files ■ Configuration file upload/download via TFTP server L2 Features Auto upgrade via TFTP server Auto-negotiation for port speed and duplex mode RMON (groups 1, 2, 3, and 9) Flow Control: BOOTP, DHCP for IP address assignment ■ IEEE 802.3x for full-duplex mode SNTP ■ Back-Pressure for half-duplex mode Event/Error Log, Syslog Spanning Tree Protocol: (Optional) ECView Pro is a powerful network management system that ■ IEEE 802.1D Spanning Tree Protocol (STP) maximizes the capabilities of Edge-Core devices with: ■ IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) ■ Topology management ■ IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) ■ Performance management ■ Loop Back Detection ■ Configuration management ■ BPDU Guard ■ Event management ■ BPDU filter ■ SNMP management ■ Root Guard Dynamic ARP Inspection ■ Auto Edge sFlow VLANs: MAC-based mirror ■ Supports 4K IEEE 802.1Q VLANs ATC ■ Port-based VLANs Delay reload ■ IEEE 802.1v protocol-based VLANs ■ Private VLANs SNMP Standards ■ GVRP RFC 1493 Bridge MIB ■ Vlan Translation RFC 3289 Differentiated Service MIB Link Aggregation: RFC 2742 SNMP Agents MIB ■ Static trunk RFC 2096 Forwarding Table MIB ■ IEEE 802.3ad Link Aggregation Control Protocol RFC 2933 IGMP MIB ■ Trunk groups: 8, Trunk links: 2~8 RFC 2233 Interface Group MIB IGMP Snooping: RFC 2668 MAU MIB ■ IGMP v1/v2/v3 snooping RFC 1213 MIB II ■ IGMP Querier RFC 2621 RADIUS Authentication Client MIB ■ IGMP filtering RFC 2819 RMON MIB MVR (Multicast VLAN Registration) RFC 2021 RMON II Probe Configuration Group DHCP Option 82 RFC 2011 SNMPv2 IP MIB DHCP dynamic provision RFC 3584 SNMP Community MIB DDM (Digital Diagnostic Monitoring) RFC 3411 SNMP Framework MIB Support for jumbo frames up to 10KB RFC 3412 SNMP-MPD MIB RFC 3413 SNMP Target MIB, SNMP Notification MIB QoS Features RFC 3414 SNMP User-Based SM MIB Priority Queues: 8 hardware queues per port RFC 3415 SNMP View Based ACM MIB Traffic classification based on IEEE 802.1p CoS, IP, and DSCP RFC 2013 TCP MIB Supports WRR and strict scheduling RFC 1215 Trap Bandwidth Control: RFC 2012 UDP MIB ■ Egress rate limiting: FE: 64K bits/sec ~ 100M bits/sec RFC 2013 TCP MIB GE: 64K bits/sec ~ 1000M bits/sec RFC 1541 DHCP Client ■ Ingress rate limiting: FE: 64K bits/sec ~ 100M bits/sec RFC 1112 IGMP GE: 64K bits/sec ~ 1000M bits/sec RFC 2236 IGMPv2 RFC 2618 RADIUS Security RFC 1757 RMON Supports IEEE 802.1X port-based/MAC-based access control RFC 1157 SNMP QoS assignment RFC 2571 SNMPv2 RADIUS authentication RFC 2030 SNTP IP Source Guard RFC 1350 TFTP Dynamic ARP Inspection TACACS Authentication Client MIB Link detection Private MIB MAC filter Quality of Service MIB TACACS+ Access Control List IEEE Standards SSH (v1.5/v2.0) IEEE 802.1D Spanning Tree Protocol and traffic priorities SSL IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1p priority tags IPv6 Features IEEE 802.1Q VLAN IPv4/IPv6 dual protocol stack IEEE 802.1v protocol-based VLANs IPv6 Address Types Stack: Unicast IEEE 802.1x port authentication IPv6 Neighbor Discovery IEEE 802.3-2005 SNMP over IPv6 Ethernet, Fast Ethernet, and Gigabit Ethernet HTTP over IPv6 Full-Duplex flow control Remote IPv6 ping Link Aggregation Control Protocol MVR6 IEEE 802.3ac VLAN tagging TEL: 886-3-5053801 FAX: 886-3-5780764 No.1, Creation Rd. III, Hsinchu Science Park, Taiwan 30077 [email protected] www.edge-core.com EC-DS-1011-01 ES3528M V2 Product Specifications www.edge-core.com Features Electromagnetic Compatibility CE Mark FCC Class A For More Information CISPR Class A To find out more about Edge-Core Networks products and solutions, visit www.edge-core.com Environmental Specifications Temperature: ■ IEC 68-2-14 About Edge-Core Networks ■ 0ºC to 55ºC (32 °F to 131 °F) standard operating Edge-Core Networks is in the business of providing innovative network solutions. ■ -20ºC to 70ºC (-4 °F to 158 °F) non-operating In the service provider network, in the data center or in the cloud, Edge-Core Humidity: 5% to 95% non-condensing Networks delivers the software and systems that transform the way the world Vibration: IEC 68-2-36, IEC 68-2-6 connects. Edge-Core Networks serves customers and partners worldwide. Shock: IEC 68-2-29 Additional information can be found at www.edge-core.com. Drop: IEC 68-2-32 Mechanical To purchase Edge-Core Networks solutions, please contact your Edge-Core Dimensions (H x W x D): 4.3 x 44 x 17.1 cm (1.69 x 17.32 x 6.73 in.) (1RU) Networks representative at 886 3 668 6111 or authorized reseller. LED Indicators: Port, Uplink, System, Diagnostic Weight: TBD Safety CSA/NRTL (UL1950, CSA 22.2.9.50) TUV/GS (EN60950) Warranty Please check www.edge-core.com for the warranty terms in your country. © Copyright 2011 Edge-Core Networks Corp. The information contained herein is subject to change without notice. This document is for informational purposes only and does not set forth any warranty, expressed or implied, concerning any equipment, equipment feature, or service offered by Edge-Core Networks. Edge-Core Networks shall not be liable for technical or editorial errors or omissions contained herein. Ordering Information Model Number Product Description Pluggable
Load more

Recommended publications
  • Gigabit Ethernet - CH 3 - Ethernet, Fast Ethernet, and Gigabit Ethern
    Switched, Fast, and Gigabit Ethernet - CH 3 - Ethernet, Fast Ethernet, and Gigabit Ethern.. Page 1 of 36 [Figures are not included in this sample chapter] Switched, Fast, and Gigabit Ethernet - 3 - Ethernet, Fast Ethernet, and Gigabit Ethernet Standards This chapter discusses the theory and standards of the three versions of Ethernet around today: regular 10Mbps Ethernet, 100Mbps Fast Ethernet, and 1000Mbps Gigabit Ethernet. The goal of this chapter is to educate you as a LAN manager or IT professional about essential differences between shared 10Mbps Ethernet and these newer technologies. This chapter focuses on aspects of Fast Ethernet and Gigabit Ethernet that are relevant to you and doesn’t get into too much technical detail. Read this chapter and the following two (Chapter 4, "Layer 2 Ethernet Switching," and Chapter 5, "VLANs and Layer 3 Switching") together. This chapter focuses on the different Ethernet MAC and PHY standards, as well as repeaters, also known as hubs. Chapter 4 examines Ethernet bridging, also known as Layer 2 switching. Chapter 5 discusses VLANs, some basics of routing, and Layer 3 switching. These three chapters serve as a precursor to the second half of this book, namely the hands-on implementation in Chapters 8 through 12. After you understand the key differences between yesterday’s shared Ethernet and today’s Switched, Fast, and Gigabit Ethernet, evaluating products and building a network with these products should be relatively straightforward. The chapter is split into seven sections: l "Ethernet and the OSI Reference Model" discusses the OSI Reference Model and how Ethernet relates to the physical (PHY) and Media Access Control (MAC) layers of the OSI model.
    [Show full text]
  • Spec TEG-S40TXD(English).Pdf
    TRENDnet TRENDware, USA TEG-S40TXD What's Next in Networking 4-Port 10/100/1000Mbps Copper Gigabit Ethernet Switch TRENDnet’s TEG-S40TXD Copper Gigabit Switch consist of four 10/100/1000Mbps Copper Gigabit Ethernet ports with each port having Auto-negotiation and Auto-MDIX features. The Switch offers a reliable and affordable LAN solution to meet immediate bandwidth demand. Users can connect Server(s) to the Gigabit port(s) to increase network performance or cascade Copper Gigabit Switches together to create high-bandwidth Gigabit backbones. TRENDnet’s TEG- S40TXD provides simple migration, scalability, and flexibility to handle new applications and data types making it a highly reliable and cost effective solution for high-speed network connectivity. Features Benefits 4 x 10/100/1000Mbps Copper Gigabit Ethernet Integration Friendly: Ports Plug-n-Play. Connects with current Fast Ethernet Cat. 5 cables. Full/Half duplex transfer mode for each port (1000Mbps in full-duplex only) Flexible: All ports automatically negotiate Auto-MDIX on each port 10/100/1000Mbps network speed. All ports are Auto-MDIX; connection can Supports store-and-forward switching architecture be made with either a straight through with non-blocking full wire-speed performance or a crossover cable. Supports aging function and 802.3x flow control for Expandability: full-duplex mode and back pressure flow control for Cascade Gigabit Switches together to half-duplex mode operation create a Gigabit backbone. Up to 8K unicast addresses entities per device Performance: Gigabit
    [Show full text]
  • Ethernet and Wifi
    Ethernet and WiFi hp://xkcd.com/466/ CSCI 466: Networks • Keith Vertanen • Fall 2011 Overview • Mul?ple access networks – Ethernet • Long history • Dominant wired technology – 802.11 • Dominant wireless technology 2 Classic Ethernet • Ethernet – luminferous ether through which electromagne?c radiaon once thought to propagate – Carrier Sense, Mul?ple Access with Collision Detec?on (CSMA/CD) – IEEE 802.3 Robert Metcalfe, co- inventor of Ethernet 3 Classic Ethernet • Ethernet – Xerox Ethernet standardized as IEEE 802.3 in 1983 – Xerox not interested in commercializing – Metcalfe leaves and forms 3Com 4 Ethernet connec?vity • Shared medium – All hosts hear all traffic on cable – Hosts tapped the cable – 2500m maximum length – May include repeaters amplifying signal – 10 Mbps bandwidth 5 Classic Ethernet cabling Cable aSer being "vampire" tapped. Thick Ethernet cable (yellow), 10BASE-5 transceivers, cable tapping tool (orange), 500m maximum length. Thin Ethernet cable (10BASE2) with BNC T- connector, 185m maximum length. 6 Ethernet addressing • Media Access Control address (MAC) – 48-bit globally unique address • 281,474,976,710,656 possible addresses • Should last ?ll 2100 • e.g. 01:23:45:67:89:ab – Address of all 1's is broadcast • FF:FF:FF:FF:FF:FF 7 Ethernet frame format • Frame format – Manchester encoded – Preamble products 10-Mhz square wave • Allows clock synch between sender & receiver – Pad to at least 64-bytes (collision detec?on) Ethernet 802.3 AlternaWng 0's 48-bit MAC and 1's (except addresses SoF of 11) 8 Ethernet receivers • Hosts listens to medium – Deliver to host: • Any frame with host's MAC address • All broadcast frames (all 1's) • Mul?cast frames (if subscribed to) • Or all frames if in promiscuous mode 9 MAC sublayer • Media Access Control (MAC) sublayer – Who goes next on a shared medium – Ethernet hosts can sense if medium in use – Algorithm for sending data: 1.
    [Show full text]
  • Towards 100 Gbps Ethernet: Development of Ethernet / Physical Layer Aspects
    SEMINAR ON TOPICS IN COMMUNICATIONS ENGINEERING 1 Towards 100 Gbps Ethernet: Development of Ethernet / Physical Layer Aspects Ömer Bulakci Abstract — Physical layer features of Ethernet from the first released clauses and ongoing architecture researches for 100 realization towards the 100 Gb Ethernet (100 GbE) development GbE are elaborated. have been considered. Comparisons of these features are made according to the standardized data rates. Feasible physical layer TABLE I options are then discussed for high data rates. Milestones of 802.3 IEEE Standard I. INTRODUCTION Clause Date of Bit Physical THERNET is the most widely deployed Local Area Name Release Rate Medium Network (LAN) protocol and has been extended to E 802.3a Single Metropolitan Area Networks (MAN) and Wide Area (Thin Ethernet) 1985 10 Mbps Thin Coaxial Networks (WAN) [1]. The major advantages that characterize (Cheapernet) Cable Ethernet can be stated as its cost efficiency, traditional tenfold bit rate increase (from 10 Mbps to 100 Gbps), simplicity, high 802.3i 1990 10 Mbps TP Copper transmission reliability and worldwide interoperability 802.3j 1993 10 Mbps Two MMFs between vendors [2]. TP Copper The first experimental Ethernet was developed during the 802.3u 1995 100 Mbps Two Fibers early 1970s by XEROX Corporation in a coaxial cable (Fast Ethernet) (MMF,SMF) network with a data rate about 3 Mbps [3]. The initial 802.3z 1998 1 Gbps MMF, SMF standardization process of Ethernet was started in 1979 by (Gigabit Ethernet) Digital Equipment Corporation (DEC), Intel and Xerox. In 802.3ab 1999 1 Gbps TP Copper 1980, DIX Standard known as the “Thick Ethernet” was 802.3ae 2002 10 Gbps MMF,SMF released.
    [Show full text]
  • Gigabit Ethernet Gigabit Ethernet
    Gigabit Ethernet Gigabit Ethernet Vijay Moorthy, ([email protected]) Ethernet is the world's most pervasive networking technology. Gigabit Ethernet is the latest version of Ethernet. It offers 1000 Mbps ( 1 Gbps ) raw bandwidth, that is 100 times faster than the original Ethernet, yet is compatible with existing Ethernets, as it uses the same CSMA/CD and MAC protocols. When Gigabit Ethernet enters the market it will compete directly with ATM. This paper presents a survey of Gigabit Ethernet technology. Other Reports on Recent Advances in Networking Back to Raj Jain's Home Page Table of Contents 1. Introduction 1.1 History of Ethernet 1.2 Gigabit Ethernet Alliance 2. Physical Layer 2.1 1000Base-X 2.2 1000Base-T 3. MAC Layer 3.1 Carrier Extension 3.2 Packet Bursting 4. GMII ( Gigabit Media Independent Interface ) 4.1 PCS (Physical Coding Sublayer) 4.2 PMA (Physical Medium Attachment) 4.3 PMD (Physical Medium Dependent) 5. Buffered Distributor 6. Topologies 6.1 Upgrading server-switch connections 6.2 Upgrading switch-switch connections 6.3 Upgrading a Fast Ethernet backbone 6.4 Upgrading a Shared FDDI Backbone 6.5 Upgrading High Performance Workstations 7. ATM vs. Gigabit Ethernet 8. Summary 9. Bibliography and Links http://www.cis.ohio-state.edu/~jain/cis788-97/gigabit_ethernet/index.htm (1 of 12) [2/7/2000 12:24:48 PM] Gigabit Ethernet 1. Introduction Ethernet is the world's most pervasive networking technology , since the 1970's. It is estimated that in 1996, 82% of all networking equipment shipped was Ethernet. In 1995 ,the Fast Ethernet Standard was approved by the IEEE.
    [Show full text]
  • Modern Ethernet
    Color profile: Generic CMYK printer profile Composite Default screen All-In-One / Network+ Certification All-in-One Exam Guide / Meyers / 225345-2 / Chapter 6 CHAPTER Modern Ethernet 6 The Network+ Certification exam expects you to know how to • 1.2 Specify the main features of 802.2 (Logical Link Control) [and] 802.3 (Ethernet): speed, access method, topology, media • 1.3 Specify the characteristics (for example: speed, length, topology, and cable type) of the following cable standards: 10BaseT and 10BaseFL; 100BaseTX and 100BaseFX; 1000BaseTX, 1000BaseCX, 1000BaseSX, and 1000BaseLX; 10GBaseSR, 10GBaseLR, and 10GBaseER • 1.4 Recognize the following media connectors and describe their uses: RJ-11, RJ-45, F-type, ST,SC, IEEE 1394, LC, MTRJ • 1.6 Identify the purposes, features, and functions of the following network components: hubs, switches • 2.3 Identify the OSI layers at which the following network components operate: hubs, switches To achieve these goals, you must be able to • Define the characteristics, cabling, and connectors used in 10BaseT and 10BaseFL • Explain how to connect multiple Ethernet segments • Define the characteristics, cabling, and connectors used with 100Base and Gigabit Ethernet Historical/Conceptual The first generation of Ethernet network technologies enjoyed substantial adoption in the networking world, but their bus topology continued to be their Achilles’ heel—a sin- gle break anywhere on the bus completely shut down an entire network. In the mid- 1980s, IBM unveiled a competing network technology called Token Ring. You’ll get the complete discussion of Token Ring in the next chapter, but it’s enough for now to say that Token Ring used a physical star topology.
    [Show full text]
  • Ethernet Explained
    Technical Note TN_157 Ethernet Explained Version 1.0 Issue Date: 2015-03-23 The FTDI FT900 32 bit MCU series, provides for high data rate, computationally intensive data transfers. One of the interfaces used for this high speed communication is Ethernet. This application note discusses some of the key features of an Ethernet link and how the FT900 assists in establishing the link. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold FTDI harmless from any and all damages, claims, suits or expense resulting from such use. Future Technology Devices International Limited (FTDI) Unit 1, 2 Seaward Place, Glasgow G41 1HH, United Kingdom Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758 Web Site: http://ftdichip.com Copyright © 2015 Future Technology Devices International Limited Technical Note TN_157 Ethernet Explained Version 1.0 Document Reference No.: FT_001105 Clearance No.: FTDI# 442 Table of Contents 1 Introduction .................................................................................................................................... 3 1.1 Scope ....................................................................................................................................... 3 2 What is Ethernet? ........................................................................................................................... 4 2.1 Speeds ....................................................................................................................................
    [Show full text]
  • Physical Layer Standards
    ELEC3030 (EL336) Computer Networks S Chen Physical Layer Standards • Physical layer: concern with transmission of raw bit stream over physical medium • A physical layer “protocol” or standard deals with mechanical, electrical and procedural characteristics to access physical medium • Parts of a physical layer are completely related to the medium and others are independent of the medium → useful thinking physical layer as two sublayers – “Medium dependent sublayer”: specifies the medium, physical connectors, related mechanical and electrical characteristics – “Medium independent sublayer”: covers line coding – how to transmit 0 and 1 bits; synchronisation – sender and receiver clocks must be synchronised to know the start/end of a bit, usually by organising block of bits into a frame; other issues not directly linked to the medium Do not confuse layer-1 framing with framing in layer-2: It is really concerned with how to reliably transmit bit stream (timing), while layer-2 framing includes some other higher functional purposes 25 ELEC3030 (EL336) Computer Networks S Chen IEEE 802.3 Ethernet • A bus LAN, “medium dependent” part of physical layer specifies things related to the medium: Controller name (a) 10Base5 (b) 10Base2 (c) 10Base-T Controller Twisted pair Transceiver medium thick coax cable thin coax cable twisted pair Transceiver + controller cable max. length 500 m 200 m 100 m Core Vampire tap nodes 100 30 1024 data rate 10 Mbps 10 Mbps 10 Mbps Transceiver Connector Hub (a) (b) (c) • “Medium independent”: the Manchester encoding is
    [Show full text]
  • ETHERNET TECNOLOGIES 1º: O Que É Ethernet ?
    ETHERNET TECNOLOGIES 1º: O Que é Ethernet ? Ethernet Origem: Wikipédia, a enciclopédia livre. Este artigo ou se(c)ção cita fontes fiáveis e independentes, mas que não cobrem todo o conteúdo (desde setembro de 2012). Por favor, adicione mais referências e insira-as no texto ou no rodapé, conforme o livro de estilo. Conteúdo sem fontes poderá serremovido. Encontre fontes: Google (notícias, livros, acadêmico) — Yahoo! — Bing. Protocolos Internet (TCP/IP) Cam Protocolo ada 5.Apl HTTP, SMTP, FTP, SSH,Telnet, SIP, RDP, I icaçã RC,SNMP, NNTP, POP3, IMAP,BitTorrent, o DNS, Ping ... 4.Tra nspo TCP, UDP, RTP, SCTP,DCCP ... rte 3.Re IP (IPv4, IPv6) , ARP, RARP,ICMP, IPsec ... de Ethernet, 802.11 (WiFi),802.1Q 2.Enl (VLAN), 802.1aq ace (SPB), 802.11g, HDLC,Token ring, FDDI,PPP,Switch ,Frame relay, 1.Físi Modem, RDIS, RS-232, EIA-422, RS-449, ca Bluetooth, USB, ... Ethernet é uma arquitetura de interconexão para redes locais - Rede de Área Local (LAN) - baseada no envio de pacotes. Ela define cabeamento e sinais elétricos para a camada física, e formato de pacotes e protocolos para a subcamada de controle de acesso ao meio (Media Access Control - MAC) do modelo OSI.1 A Ethernet foi padronizada pelo IEEE como 802.3. A partir dos anos 90, ela vem sendo a tecnologia de LAN mais amplamente utilizada e tem tomado grande parte do espaço de outros padrões de rede como Token Ring, FDDI e ARCNET.1 Índice [esconder] 1 História 2 Descrição geral 3 Ethernet com meio compartilhado CSMA/CD 4 Hubs Ethernet 5 Ethernet comutada (Switches Ethernet) 6 Tipos de
    [Show full text]
  • IEEE 802.3Z Gigabit Ethernet ANSI X3T9 Fibre Channel Ethernet – Table of Contents
    IEEE 802.3 Ethernet IEEE 802.3u Fast Ethernet IEEE 802.3z Gigabit Ethernet ANSI X3T9 Fibre Channel Ethernet – Table of Contents Part 1: IEEE 802.3 Ethernet Part 2: IEEE 802.3u Fast Ethernet Floor 4 Ethernet / Fast Ethernet Switch Part 3: IEEE 802.3z Gigabit Ethernet Floor 3 Hub Stack Bridge / Router Fast WAN Ethernet Switch Floor 1 Broadband Network Technologies IEEE 802.3 Ethernet 2 Ethernet – History • Developed by Xerox Palo Alto Research Centre • First published by Digital Equipment, Intel, and Xerox as DIX (DEC, Intel, Xerox) standard • Strongly changed and standardised by IEEE in the IEEE 802.3 • Therefore, two different versions are existing: – Ethernet version 2 (DIX) – IEEE 802.3 – differences are mainly in the Media Access frame • Topology of an Ethernet is logically (mostly physically, too) a bus Broadband Network Technologies IEEE 802.3 Ethernet 3 Ethernet – Technological Overview • A lot of standards exist for different Ethernet versions: – 1Base5 (Starlan), 10Base5 (Ethernet), 10Base2 (Cheapernet) – 10BaseT, 10BaseF, 10Broad36 – 100BaseTX, 100BaseFX, 100BaseT2, 100BaseT4 – 1000Base-LX, 1000Base-SX, 1000Base-CX, 1000Base-T – 100BaseVG, 100VG-AnyLAN • First number identifies transfer rate (1=1MBit/s, 10=10MBit/s, ...) • Base = baseband transmission, Broad = broadband transmission • Last digit, number, or character identifies characteristics of the transmission medium: – T = twisted pair, FX/LX/SX = fibre optics, CX = shielded balanced copper, T4 = 4 pair twisted pair, T2 = 2 pair twisted pair – length of a segment - 2=185m,
    [Show full text]
  • FAST ETHERNET/GIGABIT ETHERNET SWITCHES 24+2+2 Managed Switch with Gigabit Connections
    FAST ETHERNET/GIGABIT ETHERNET SWITCHES 24+2+2 Managed Switch with Gigabit Connections The WideBand Professional Series 24+2+2 switches provide flexible enterprise-class connectivity with 24 Ethernet 10/100 ports, 2 Ethernet 10/100/1000 ports and 2 additional mini-GBIC slots for fiber SFPs. With Managed and Layer 3 models available, the 24+2+2 switches make adding Gigabit backbones a painless experience. Gigabit Ethernet Without Rewiring: The Professional Series switches utilize WideBand’s robust signaling technology allowing Gigabit connections over Category 5 runs in excess of 200 meters, and even over 100-meter segments of Category 3 cable. The switches have been WGNA Certified to transmit data up to a full 100 meters with a bit error rate of less than 1 per million on all grades of Category 5 cables, ensuring not just connectivity, but full bandwidth on existing network wiring. Breakthrough SPU Technology: WideBand’s Switch Processing Unit (SPU) is integrated to provide a never before seen level of management control while eliminating costly components needed in competing designs. The Managed switch models provide extensive support for VLANs, traffic prioritization, and packet filtering based on Layer 2, 3, and 4 information. Wire-speed Layer 2/3/4 Switching and IP Routing: The WideBand Professional Series switches deliver wire-speed switching and MAC address learning in a fully non-blocking architecture. The Layer 3 models add enterprise-class IP routing at wire-speed as well as QoS provisioning features based on Layer 2/3/4 and IEEE 802.1p tag information. Auto MDI/MDI-X Makes Connecting Easy: All the ports automatically detect straight-through/crossover cable types, eliminating communication problems resulting from cable type mismatches.
    [Show full text]
  • 10 Gigabit Ethernet Switching Solutions
    www.smc.com 10 gigabit ethernet switching solutions Turbo charge your network capacity with 10 Gigabit Ethernet WIRELESS BROADBAND SWITCHES VOIP NAS INTRODUCTION • The LAN-PHY was to be used with private fi bers such as: single mode fi ber (extended and long haul), multi-mode Ethernet is the enduring success story of local area networking. fi ber (short haul) to cover distances up to 40 kilometers. Now into its third decade it continues to develop and improve • The WAN-PHY can be used with existing SONET/SDH with support for faster speeds, new interfaces and longer trans- OC-192/STM-64 interfaces providing wide area support mission distances. The latest generation of Ethernet continues over metropolitan, national or even international networks. the tradition of increasing the transmission speed by tenfold to a staggering 10 Gigabit per second. It supports transmission Now with the introduction of copper based 10G Ethernet stan- distances of up to 40km when using single-mode fi ber optic ca- dards the LAN-PHY was updated to include new interface types. bling and enables critical business applications that were not The IEEE 802.3ak standard has been ratifi ed to use the high previously available using previous Ethernet standards. grade copper cable originally developed for the Inifi Band pro- prietary data center cabling standard. Most recently and cru- In this SMC Technology Primer we explain the jargon and show cially for the development of the 10G market is the introduction how you can benefi t from the latest 10 Gigabit Ethernet stan- of the IEEE802.3an standard which has been ratifi ed in 2006 dard.
    [Show full text]