Gravimetric Analysis 1

Total Page:16

File Type:pdf, Size:1020Kb

Gravimetric Analysis �1 Unit IV Gravimetric Analysis !1. Gravimetric Analysis Gravimetric methods – are quantitative methods in which the mass of the analyte or some compound that is chemically related to the analyte is determined. PRINCIPLE : Gravimetric analysis is the process of isolating and weighing an element or a definite compound of the element in as pure a form as possible. The element or compound of the element is separated from a weighed portion of the substance being examined. A large portion of the determinations in gravimetric analysis is concerned with the transformation of the element or radical to be determined into a pure stable compound which can be readily converted into a form suitable for weighing. The weight of the element or radical may then be readily calculated from a knowledge of the formula of the compound and the relative atomic masses of the constituent elements. The separation of the element or of the compound containing it may be effected in number of ways, the most important of which are 1. Precipitation Methods 2. Volatilisation or evolution methods 3. Electro analytical methods - Electro Gravimetry 1. Precipitation Methods The most important is the precipitation method in gravimetric analysis, which is explained in detail below. A weighed sample of the substance to be analysed is brought into solution by a suitable method, and the element to be determined is then precipitated as an insoluble compound. The precipitate is filtered off, washed throughly, ignited (or dried) and weighed accurately. The content of the element is calculated from the weight of the precipitate and its formula and expressed as a percentage of the sample taken. The precipitate may be collected on a filter paper or in a Gooch crucible. 2. Volatilisation or evolution methods In addition to precipitation, the other methods are also used. This Volatilisation or Evolution method depends essentially upon the removal of volatile constituents. This may be effected in several ways. (i) By simple ignition in air or in a current of an indifferent gas. (ii) By treatment with some chemical reagent whereby the desired constituent is rendered volatile and (iii) By treatment with a chemical reagent whereby the desired constituent is rendered non-volatile. The volatilised substance may be absorbed in a weighed quantity of a suitable medium when the estimation is a direct one, or the weight of the residue remaining after volatilisation of a component is determined, and the proportion of the constituent calculated from the loss in weight. 3. Electro analytical methods - Electro Gravimetry In electro-gravimetric analysis, the element to be determined is deposited electrolytically upon a suitable electrode. Filtration is not required, and provided the experimental conditions are carefully controlled, the co-deposition of two metals can often be avoided. In each of these analytical methods, the amount of a given component is found from the results of weighing . These methods can therefore be regarded as different varieties of gravimetric analysis. Unit IV Gravimetric Analysis !2. Steps Involved in Gravimetric Analysis 1. Preparation of the solution 2. Precipitation 3. Digestion 4. Filtration 5. Washing of the Precipitate 6. Drying or igniting 7. Weighing 8. Calculation 1. PREPARATION OF THE SOLUTION This may involve several steps including adjustment of the pH of the solution in order for the precipitate to occur quantitatively and get a precipitate of desired properties, removing interferences, adjusting the volume of the sample to suit the amount of precipitating agent to be added. 2. PRECIPITATION or NUCLEATION Gravimetric precipitation are usually made in beakers. Except during the actual precipitation, the beaker is covered with the clock-glass. A thin stirring rod, rounded at each end, is also required. NUCLEATION In practice, supersaturation influences one of the mechanisms of precipitation, namely nucleation and crystal growth. Nucleation is the first stage of precipitation and consists in the formation of stable microcrystals that can grow spontaneously, i.e. crystallization nuclei. Further precipitation leads to competition between new and existing nuclei (particle growth). If nucleation predominates, then a crystal will form that is easy to filter. Low supersaturation encourages the growth of existing microcrystals rather than the formation of new nuclei. Higher temperatures also favour the formation of crystalline precipitates, because they increase the solubility of the precipitate (S), and other factors that encourage crystal growth are diluting the solution (Q), and adding the precipitation agent slowly while shaking energetically. PRECIPITATION The solution of the precipitating reagents is usually added slowly from a teat pipette or burette. with efficient stirring, to a suitably diluted solution of the sample. Efficient stirring. is necessary to avoid the possible high local concentrations of precipitating reagent which would tend to give contamination of precipitate due to co-precipitation. The reagent is introduced down the side of the beaker to avoid splashing. Precipitation is usually made from hot dilute solutions, a procedure which tends to give an easily Unit IV Gravimetric Analysis !3. filterable precipitate and reduces the possibility of co-precipitation. The formation of coarse particles is favoured by slow addition of the precipitant. vigorous stirring of the solution during precipitation and by carrying out the precipitation from hot solutions. Only a moderate excess of precipitating reagent is required. When the precipitate has settled somewhat. a few more drops of precipitant should be added to test for the completeness of precipitation; if further precipitation occurs. then the process of addition of precipitant, stirring and allowing the precipitation settle and testing again must be carried out until there is no doubt about completeness of precipitation. The stirring rod should not come into contact with the sides or bottom of the beaker during stirring in order to avoid scratching particles of glass from the surfaces. Also, a scratched surface is difficult to wash clean. Reagents should be examined for the clarity before use and filtered if necessary. Before filtration, precipitates may need to be digested by allowing them to stand overnight, or by heating the precipitate and its supernatant liquid nearly to boiling point for some time. Digestion in this manner increases the degree of coarseness of the precipitate: A further check for completeness of precipitation should be carried out when the supernatant liquid becomes clear during the period of digestion. No further precipitate should be produced when a few drops of the must be added as described above. If the precipitate is much more soluble in hot water than in cold, the solution is allowed to cool to room temperature, before filtration. Otherwise, solutions are filtered hot to speed up the filtration. (i) CO-PRECIPITATION When a precipitate separates from a solution, it is not always perfectly pure: it may contain varying amounts of impurities dependent upon the nature of the precipitate and the conditions of precipitation. The contamination of the precipitate by substances which are normally soluble in the mother liquor is termed co- precipitation. Hence the term co-precipitation is a phenomenon in which the soluble compounds are removed from solution during precipitate formation. It is important to understand that the solution is not saturated with the co- precipitated species. Moreover, contamination of a precipitate by a second substance whose solubility product has been exceed does not constitute co-precipitation. Types of Co-precipitation There are four types of co-precipitation: (i) Surface adsorption (ii) Mixed crystal formation (iii) Occlusion (iv) Mechanical entrapment. Surface adsorption and mixed crystal formation are equilibrium processes., where as occlusion and mechanical entrapment arise from the kinetics of crystal growth. (i) Surface adsorption: Adsorption is a common source of co-precipitation that is likely to cause significant contamination of precipitates with large specific surface areas i.e., coagulated colloids. Note the extensive internal surface area exposed to solvent Although adsorption does occur in crystalline solids, its effect on purity are usually undetectable because of the relatively small, Unit IV Gravimetric Analysis !4. specific surface area of these solids. Coagulation of a colloid does not significantly decrease the amount of adsorption because the coagulated solid still contains large internal surface areas that remain exposed to the solvent which can be seen in the figure. The co-precipitated contaminant on the coagulated colloid consists of the lattice ion originally adsorbed on the surface before coagulation and the counter ion of opposite charge held in the film of solution immediately adjacent to the particle. The net effect of surface adsorption is therefore the carrying down of an otherwise soluble compound as a surface contaminant. For example The coagulated silver chloride formed in the gravimetric determination of chloride ion is contaminated with primarily adsorbed silver ions along with nitrate or other anions in the counter-ion layer. As a consequence, silver nitrate, a normally soluble compound, is co-precipitated with the silver chloride. (ii) Mixed - Crystal formation Mixed-crystal formation is a type of co-precipitation in which a contaminant ion replaces an ion in the lattice of crystal. In mixed-crystal formation,
Recommended publications
  • Chapter 8: Gravimetric Methods
    Chapter 8 Gravimetric Methods Chapter Overview 8A Overview of Gravimetric Methods 8B Precipitation Gravimetry 8C Volatilization Gravimetry 8D Particulate Gravimetry 8E Key Terms 8F Chapter Summary 8G Problems 8H Solutions to Practice Exercises Gravimetry includes all analytical methods in which the analytical signal is a measurement of mass or a change in mass. When you step on a scale after exercising you are making, in a sense, a gravimetric determination of your mass. Mass is the most fundamental of all analytical measurements, and gravimetry is unquestionably our oldest quantitative analytical technique. The publication in 1540 of Vannoccio Biringuccio’sPirotechnia is an early example of applying gravimetry—although not yet known by this name—to the analysis of metals and ores.1 Although gravimetry no longer is the most important analytical method, it continues to find use in specialized applications. 1 Smith, C. S.; Gnodi, M. T. translation of Biringuccio, V. Pirotechnia, MIT Press: Cambridge, MA, 1959. 355 356 Analytical Chemistry 2.0 8A Overview of Gravimetric Methods Before we consider specific gravimetric methods, let’s take a moment to develop a broad survey of gravimetry. Later, as you read through the de- scriptions of specific gravimetric methods, this survey will help you focus on their similarities instead of their differences. You will find that it is easier to understand a new analytical method when you can see its relationship to other similar methods. 8A.1 Using Mass as an Analytical Signal Method 2540D in Standard Methods for Suppose you are to determine the total suspended solids in the water re- the Examination of Waters and Wastewaters, leased by a sewage-treatment facility.
    [Show full text]
  • Gravimetric Analysis
    Gravimetric Analysis Gravimetric Analysis can be used to determine the percent composition of a species in a compound. This is known as quantitative analysis. An agent (precipitating agent) is chosen which will cause the species of interest to precipitate out of solution. The precipitate is then isolated and weighed. Through a series of calculations, the amount of the species in the original sample or compound can then be determined. 1. Weigh accurately about 0.5 g of the unknown, and dissolve it in water. The volume of water is not important, but you do want to make sure the solid is completely dissolved. 2. Add the precipitating agent in the form of solution. For example, to precipitate a chloride use a soluble salt of silver (AgNO3). 3. Add the precipitating agent until no more solid seems to precipitate. Allow the mixture to sit for about 5 minutes, and then add a few drops more, observing to see if any more precipitation occurs. If you see more solid forming, keep repeating the steps until no more precipitate results. Now separate the solid from the liquid. The mixture can be filtered by vacuum filtration through a weighed filter paper. Other methods involve gravity filtration or use of a centrifuge. Allow the solid to dry until you get a constant weight for readings at subsequent times (at least overnight or through use of an oven). 4. From the mass of precipitated compound (ppt) and the formula (in this case AgCl), you can calculate the percent composition of a species (in this case Cl-) in the original sample.
    [Show full text]
  • Lecture 10. Analytical Chemistry What Is Analytical Chemistry ?
    5/5/2019 What is Analytical Chemistry ? It deals with: Lecture 10. • separation Analytical Chemistry • identification • determination of components in a sample. Basic concepts It includes coverage of chemical equilibrium and statistical treatment of data. It encompasses any type of tests that provide information relating to the chemical composition of a sample. 1 2 • Analytical chemistry is divided into two areas of analysis: • The substance to be analyzed within a sample • Qualitative – recognizes the particles which are present in a sample. is known as an analyte, whereas the substances which may cause incorrect or • Quantitative – identifies how much of inaccurate results are known as chemical particles is present in a sample. interferents. 3 4 1 5/5/2019 Qualitative analysis is used to separate an analyte from interferents existing in a sample and detect the previous one. It gives negative, positive, or yes/no types of data. Qualitative analysis It informs whether or not the analyte is present in a sample. 5 6 Examples of qualitative analysis 7 8 2 5/5/2019 Analysis of an inorganic sample The classical procedure for systematic analysis of an inorganic sample consists of several parts: preliminary tests (heating, solubility in water, appearance of moisture) more complicated tests e.g. introducing the sample into a flame and noting the colour produced; determination of anionic or cationic constituents of 9 solute dissolved in water 10 Flame test Sodium Bright yellow (intense, persistent) Potassium Pale violet (slight, fleeting) Solutions of ions, when mixed with concentrated Calcium Brick red (medium, fleeting) HCl and heated on a nickel/chromium wire in a flame, cause the flame to change to a colour Strontium Crimson (medium) characteristic of the element.
    [Show full text]
  • 1 Introduction of Mass Spectrometry and Ambient Ionization Techniques
    1 1 Introduction of Mass Spectrometry and Ambient Ionization Techniques Yiyang Dong, Jiahui Liu, and Tianyang Guo College of Life Science & Technology, Beijing University of Chemical Technology, No. 15 Beisanhuan East Road, Chaoyang District, Beijing, 100029, China 1.1 Evolution of Analytical Chemistry and Its Challenges in the Twenty-First Century The Chemical Revolution began in the eighteenth century, with the work of French chemist Antoine Lavoisier (1743–1794) representing a fundamental watershed that separated the “modern chemistry” era from the “protochemistry” era (Figure 1.1). However, analytical chemistry, a subdiscipline of chemistry, is an ancient science and its metrological tools, basic applications, and analytical processes can be dated back to early recorded history [1]. In chronological spans covering ancient times, the middle ages, the era of the nineteenth century, and the three chemical revolutionary periods, analytical chemistry has successfully evolved from the verge of the nineteenth century to modern and contemporary times, characterized by its versatile traits and unprecedented challenges in the twenty-first century. Historically, analytical chemistry can be termed as the mother of chemistry, as the nature and the composition of materials are always needed to be iden- tified first for specific utilizations subsequently; therefore, the development of analytical chemistry has always been ahead of general chemistry [2]. During pre-Hellenistic times when chemistry did not exist as a science, various ana- lytical processes, for example, qualitative touchstone method and quantitative fire-assay or cupellation scheme have been in existence as routine quality control measures for the purpose of noble goods authentication and anti-counterfeiting practices. Because of the unavailability of archeological clues for origin tracing, the chemical balance and the weights, as stated in the earliest documents ever found, was supposed to have been used only by the Gods [3].
    [Show full text]
  • Conceptual Approach to Thermal Analysis and Its Main Applications
    Prospect. Vol. 15, No. 2, Julio-Diciembre de 2017, 117-125 Conceptual approach to thermal analysis and its main applications Aproximación conceptual al análisis térmico y sus principales aplicaciones Alejandra María Zambrano Arévalo1*, Grey Cecilia Castellar Ortega2, William Andrés Vallejo Lozada3, Ismael Enrique Piñeres Ariza4, María Mercedes Cely Bautista5, Jesús Sigifredo Valencia Ríos6 1*M.Sc. Chemical Sciences, Full Professor, Universidad de la Costa. Barranquilla-Colombia. 2M.Sc. Chemical Sciences, Full Professor, Universidad Autónoma del Caribe. Barranquilla-Colombia. 3Ph.D. Chemical Sciences, Full Professor, Universidad del Atlántico. Barranquilla-Colombia. 4M.Sc. Physical Sciences, Occasional Full Professor, Universidad del Atlántico. Barranquilla-Colombia. 5Ph.D. Engineering, Full Professsor, Universidad Autónoma del Caribe. Barranquilla-Colombia. 6Ph. D. Universidad Nacional de Colombia, Vicerrector Universidad Nacional de Colombia (Sede Palmira). Palmira-Colombia. E-mail: [email protected] Recibido 12/04/2017 Cite this article as: A. Zambrano, G.Castellar, W.Vallejo, I.Piñeres, M.M. Aceptado 28/05/2017 Cely, J.Valencia, Aproximación conceptual al análisis térmico y sus principales aplicaciones, “Conceptual approach to thermal analysis and its main applications”. Prospectiva, Vol 15, N° 2, 117-125, 2017. ABSTRACT This work shows to the reader a general description about the techniques of classic thermal analysis as known as Differential Scanning Calorimetry (DSC), Differential Thermal Analysis (DTA) and Thermal Gravimetric Analysis. These techniques are very used in science and material technologies (metals, metals alloys, ceramics, glass, polymer, plastic and composites) with the purpose of characterizing precursors, following and control of process, adjustment of operation conditions, thermal treatment and verifying of quality parameters. Key words: Physical chemistry; Calorimetry; Thermochemistry; Thermal analysis.
    [Show full text]
  • Physicochemical Characteristics of Protein Isolated from Thraustochytrid Oilcake
    foods Article Physicochemical Characteristics of Protein Isolated from Thraustochytrid Oilcake Thi Linh Nham Tran 1,2, Ana F. Miranda 1 , Aidyn Mouradov 1,* and Benu Adhikari 1 1 School of Science, RMIT University, Bundoora Campus, Melbourne, VIC 3083, Australia; [email protected] (T.L.N.T.); [email protected] (A.F.M.); [email protected] (B.A.) 2 Faculty of Agriculture Bac Lieu University, 8 wards, Bac Lieu 960000, Vietnam * Correspondence: [email protected]; Tel.: +61-3-99257144 Received: 13 May 2020; Accepted: 8 June 2020; Published: 11 June 2020 Abstract: The oil from thraustochytrids, unicellular heterotrophic marine protists, is increasingly used in the food and biotechnological industries as it is rich in omega-3 fatty acids, squalene and a broad spectrum of carotenoids. This study showed that the oilcake, a by-product of oil extraction, is equally valuable as it contained 38% protein/dry mass, and thraustochytrid protein isolate can be obtained with 92% protein content and recovered with 70% efficiency. The highest and lowest solubilities of proteins were observed at pH 12.0 and 4.0, respectively, the latter being its isoelectric point. Aspartic acid, glutamic acid, histidine, and arginine were the most abundant amino acids in proteins. The arginine-to-lysine ratio was higher than one, which is desired in heart-healthy foods. The denaturation temperature of proteins ranged from 167.8–174.5 ◦C, indicating its high thermal stability. Proteins also showed high emulsion activity (784.1 m2/g) and emulsion stability (209.9 min) indices. The extracted omega-3-rich oil melted in the range of 30–34.6 ◦C and remained stable up to 163–213 ◦C.
    [Show full text]
  • High Performance Liquid Chromatography Method Development and Chemometric Analysis of Ecstasy and Cocaine
    institlüld ictterkcnny TeicneoUiochti institute lyit (.«Ulf C*»n«lon of Technology High performance liquid chromatography method development and chemometric analysis of ecstasy and cocaine Kim McFadden Supervisors Dr. B. F. Carney, Letterkenny Institute of Technology Dr. D. O'Driscoll, Forensic Science Laboratory, Dublin Submitted to Higher bducation and Training Awards Council (HETAC) in fulfilment for the requirements for the degree of Doctor of Philosophy HPLC method development & chemomelric analysis of ecstasy & cocaine Declaration I hereby declare that the work herein, submitted for Ph.D. in Analytical Science at Letterkenny Institute of Technology, is the result of my own investigation, except where reference is made to published literature. I also certify that the material submitted in this thesis has not been previously submitted for any other qualification. Kim McFadden 1 HPLC method development & chemometric analysis of ecstasy & cocaine Table of Contents Declaration 1 Abstract 5 List of Abbreviations 7 List of Figures 10 List of Tables 14 List of Presentations and Publications 16 Acknowledgments 18 Chapter 1: Literature review. 19 1.1. Introduction. 20 1.2. Drugs of abuse. 21 1.2.1. Narcotics. 22 1.2.2. Depressants. 24 1.2.3. Stimulants. 24 1.2.4. Hallucinogens. 25 1.2.5. Ecstasy. 26 1.2.6. Cocaine. 31 1.3. Current analytical techniques for forensic drug analysis. 34 1.3.1. Spectrometric methods. 34 1.3.2. Chromatographic methods. 36 1.4. Fundamentals of High Performance Liquid Chromatography. 40 1.4.1. Chromatographic interactions. 40 1.4.2. Mobile phase. 41 1.4.3. The column. 42 1.4.4.
    [Show full text]
  • Ch 27 Gravimetric Analysis Analytical Chemistry
    Ch 27 Gravimetric Analysis 1 Analytical chemistry Classification by the techniques: 1. Classical Analysis Gravimetric, Titration(Volumetric) Analysis 2. Instrumental Analysis Electrochemical Analysis, Spectrochemical Analysis, Chromatographic Separation and Analysis 2 1 Ch 12 Gravimetric Analysis gravi – metric (weighing - measure) Definition: A precipitation or volatilization method based on the determination of weight of a substance of known composition that is chemically related to the analyte. 3 12. 1 Procedure Criteria (1)The desired substance: completely precipitated. "common ion" effect can be utilized: Ag+ + Cl- AgCl(s) excess of Cl- which is added (2) The weighed form: known composition. (3) The product: "pure", easily filtered.. 4 2 12. 1 Procedure • 7 Steps in Gravimetric Analysis 1) Dry and weigh sample 2) Dissolve sample 3) Add precipitating reagent in excess 4) Coagulate precipitate usually by heating 5) Filtration-separate precipitate from mother liquor 6) Wash precipitate 7) Dry and weigh to constant weight (0.2-0.3 mg) 5 Suction Filtration • Filter flask • Buchner funnel • Filter paper • Glass frit • Filter adapter • Heavy-walled rubber tubing • Water aspirator 6 3 Suction Filtration • Mother liquor 7 12.2 Advantages/Disadvantages • Experimentally simple and elegant • Accurate • Precise (0.1-0.3 %) • Macroscopic technique-requires at least 10 mg ppt to collect and weigh properly • Time-consuming (1/2 day?) 8 4 12.3 Calculation • Design of experiment • Content Calculation • Evaluation of the results 9 12.3 Calculation • % of analyte, % A • %A = weight of analyte x 100 weight of sample • weight of ppt directly obtained ->%A 10 5 How Do We Get %A? • % A = weight of ppt x gravimetric factor (G.F.) x 100 weight of sample • G.F.
    [Show full text]
  • Analytical Methodologies
    ANALYTICAL METHODOLOGIES Qualitative Analysis – provides presence/absence information only (i.e., microbial screening) Quantitative Analysis – provides a measure of concentration (a number plus units) 1. Classical methods – ‘wet chemistry’ a) Gravimetric analysis (based on mass of analyte containing precipitate) b) Volumetric analysis (based on the volume of titrant required to reach end- point) Classical methods are generally accurate and precise, but may be time consuming and are usually limited to analysis of reasonably high concentrations of analyte (i.e., > 1 ppm) 2. Instrumental methods measure some form of a sensor/detector signal (usually a voltage or current) that is related either directly or indirectly to the analyte concentration via a calibration process. Instrumental methods are generally accurate, precise and readily automated, however require careful calibration procedures. a) electrochemical devices convert chemical concentrations directly into a measured voltage potential or electric current. examples: dissolved oxygen (DO) meter ion selective electrode (ISE) b) spectrophotometric instruments involve the interaction of the analyte with electromagnetic radiation (light) examples: UV/vis (colourimetric) atomic absorption spectrophotmetry (AAS) atomic emission spectrophotmetry (AES) atomic fluorescence spectrophotmetry (AFS) c) chromatographic instruments serve to separate and quantify members of a closely related series of analytes examples: gas chromatography (GC) high performance liquid chromatography (HPLC) ion chromatography (IC) capillary electrophoresis (CE) 3. Tandem Instrumental methods combine instruments in sequence, often coupling chromatographic separation with sensitive and selective detectors, such as mass spectrometry (MS) example: GC-MS/MS ANALYTICAL METHODOLOGIES 2016.doc Gravimetric Analysis A precipitating reagent is added to convert a soluble analyte species into an insoluble solid that contains the analyte in some known combination.
    [Show full text]
  • Chapter 25: Fundamentals of Analytical Chemistry
    Manahan, Stanley E. "FUNDAMENTALS OF ANALYTICAL CHEMISTRY" Fundamentals of Environmental Chemistry Boca Raton: CRC Press LLC, 2001 25 FUNDAMENTALS OF ANALYTICAL CHEMISTRY __________________________ 25.1 NATURE AND IMPORTANCE OF CHEMICAL ANALYSIS Analytical chemistry is that branch of the chemical sciences employed to determine the composition of a sample of material. A qualitative analysis is performed to determine what is in a sample. The amount, concentration, composition, or percent of a substance present is determined by quantitative analysis. Sometimes both qualitative and quantitative analyses are performed as part of the same process. Analytical chemistry is important in practically all areas of human endeavor and in all spheres of the environment. Industrial raw materials and products processed in the anthrosphere are assayed by chemical analysis, and analytical monitoring is employed to monitor and control industrial processes. Hardness, alkalinity, and trace-level pollutants (see Chapters 11 and 12) are measured in water by chemical analyses. Nitrogen oxides, sulfur oxides, oxidants, and organic pollutants (see Chapters 15 and 16) are determined in air by chemical analysis. In the geosphere (see Chapters 17 and 18), fertilizer constituents in soil and commercially valuable minerals in ores are measured by chemical analysis. In the biosphere, xenobiotic materials and their metabolites (see Chapter 23) are monitored by chemical analysis. Analytical chemistry is a dynamic discipline. New chemicals and increasingly sophisticated instruments and computational capabilities are constantly coming into use to improve the ways in which chemical analyses are done. Some of these improvements involve the determination of ever smaller quantities of substances; others greatly shorten the time required for analysis; and some enable analysts to tell with much grater specificity the identities of a large number of compounds in a complex sample.
    [Show full text]
  • Geochemistry Guide 2020 the Foundation of Project Success
    GEOCHEMISTRY GUIDE 2020 THE FOUNDATION OF PROJECT SUCCESS ABOUT SGS COMMITMENT TO QUALITY ON-SITE LABORATORIES COMMERCIAL TESTING SERVICES SUPPORT ACROSS THE PROJECT LIFECYCLE ADDITIONAL INFORMATION TECHNICAL GUIDE GEOCHEMISTRY GUIDE 2020 1 ABOUT SGS By incorporating an integrated approach, we deliver testing and expertise Whether your requirements are in the throughout the entire mining life cycle. Our services include: field, at a mine site, in a smelting and refining plant, or at a port, SGS has the • Helping you to understand your resources with a full-suite of geological experience, technical solutions and services, including XploreIQ, laboratory professionals to help you reach • Offering innovative analytical testing capabilities through dedicated on-sites, your goals efficiently and effectively. FAST or one of commercial laboratories, • Consulting and designing metallurgical testing programs, unique to your deposit, VISIT US AT: • Optimizing recovery and throughput through process control services, WWW.SGS.COM/MINING • Keeping final product transparent through impartial trade analysis, • Ensuring safe operations for employees while helping to mitigate environmental impact. GEOCHEMISTRY GUIDE 2020 2 COMMITMENT TO QUALITY SGS is committed to customer satisfaction and providing a consistent level of quality service that sets the industry benchmark. SGS management and staff are appropriately empowered to ensure these requirements are met. All employees and contractors are familiar with the requirements of the Quality Management System, the above objectives and process outcomes. Click here to learn more SAMPLE INTEGRITY Sample integrity is at the core of our operations, ensuring your project and its associated data is treated responsibly and transparently. To comply with regulatory oversight, samples must be collected and handled correctly.
    [Show full text]
  • Radiochemical Analysis: Activation Analysis, Instrumentation, Radiation Techniques, and Radioisotope Techniques July 1964 to June 1965
    NAT'L INST OF STAND & TECH R.I.C. mil in mi mi ii 111 inn A111DS 3S3fibM National Bureau 01 oiwiuarua Refer Library,.ibr N.UL^ldg ffg'l4^6 taken ^ecltniccil ^lote 276 RADIOCHEMICAL ANALYSIS: ACTIVATION ANALYSIS, INSTRUMENTATION, RADIATION TECHNIQUES, AND RADIOISOTOPE TECHNIQUES JULY 1964 TO JUNE 1965 U. S. DEPARTMENT OF COMMERCE NATIONAL BUREAU OF STANDARDS THE NATIONAL BUREAU OF STANDARDS The National Bureau of Standards is a principal focal point in the Federal Government for assur- ing maximum application of the physical and engineering sciences to the advancement of technology in industry and commerce. Its responsibilities include development and maintenance of the national standards of measurement, and the provisions of means for making measurements consistent with those standards; determination of physical constants and properties of materials; development of methods for testing materials, mechanisms, and structures, and making such tests as may be neces- sary, particularly for government agencies; cooperation in the establishment of standard practices for incorporation in codes and specifications; advisory service to government agencies on scientific and technical problems; invention and development of devices to serve special needs of the Govern- ment; assistance to industry, business, and consumers in the development and acceptance of com- mercial standards and simplified trade practice recommendations; administration of programs in cooperation with United States business groups and standards organizations for the development of international standards of practice; and maintenance of a clearinghouse for the collection and dissemination of scientific, technical, and engineering information. The scope of the Bureau's activities is suggested in the following listing of its three Institutes and their organizational units.
    [Show full text]