DOCSLIB.ORG

How to Draft a Skirt Block

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
How to Draft a Skirt Block How to Draft a Skirt Block Course Outline Module 1: Introduction Module 2: How to Measure Module 3: Complete Calculations Module 4: Drafting Initial Template Module 5: Drafting Skirt Front (1 Dart) Module 6: Drafting Skirt Back (1 Dart) Module 7: Drafting Skirt Front (2 Dart) Module 8: Drafting Skirt Back (2 Dart) Module 9: Drafting for Fuller Figures Module 10: Trace the Draft Module 11: Make Sample Module 12: Fit Sample Module 13: Pattern Amendments Module 14: Finalise Block Module 15: Draft a Waistband Module 16: Draft a Shaped Waistband Module 17: Draft a Facing Module 18: Draft a Lining Module 19: The End How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 1 Introduction 8:26mins Chapter 1: What is a Skirt Block 00:33 Chapter 2: Suggested Materials 03:31 Key Learnings: What you will learn in the class Tools and equipment required How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 2 How to Measure 31:51mins Chapter 1: Measure Mannequin 00:33 Chapter 2: Measure Person 09:14 Chapter 3: Measure Fuller Figure 16:54 Chapter 4: Measure Yourself 22:35 Key Learnings: Understand the correct location of the waist, high hip and low hip Learn how to measure accurately The differences in measuring a fuller figure Tips for measuring yourself How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 3 Complete Calculations 33:38mins Chapter 1: Understand Ease 01:51 Chapter 2: Ease Amount (Smaller Size) 02:59 Chapter 3: Ease Amount (Fuller Figure) 05:30 Chapter 4: Skirt Block Calculations Step 2 10:26 Chapter 5: Skirt Block Calculations Step 3 15:53 Chapter 6: Why Darts? 16:13 Chapter 7: 1 Dart Skirt Block 23:08 Chapter 8: 2 Dart Skirt Block 25:22 Chapter 9: No Darts 27:13 Chapter 10: Use a 2 Dart Skirt Block 28:10 Chapter 11: Excel Sheet 28:55 Key Learnings: Understand ease, why it is required in a garment Ease measurements for smaller sizes and fuller figures Convert your measurements into figures for drafting Understand the importance of darts and how to calculate them How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 4 Drafting Initial Template 18:45mins Chapter 1: Tools and Equipment 02:15 Chapter 2: Drafting Tips 06:19 Chapter 3: Drafting Template 07:37 Chapter 4: Depth Measurements 13:52 Key Learnings: Tools and equipment for pattern cutting Drafting tips Complete the initial template using the measurements calculated in Module 3 Draft the template for the front and back of the skirt How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 5 Drafting Skirt Front (1 Dart) 13:54mins Chapter 1: Side Seam Calculation 04:38 Chapter 2: Dart Calculation 05:22 Chapter 3: Low Hip 09:19 Chapter 4: High Hip 10:08 Key Learnings: Apply your measurements to the initial template (Module 4) Draft the front of a 1 dart skirt block How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 6 Drafting Skirt Back (1 Dart) 20:45mins Chapter 1: Centre Back Dart 00:53 Chapter 2: Side Seam Calculation 05:44 Chapter 3: Dart Calculation 06:07 Chapter 4: Low Hip 10:11 Chapter 5: High Hip 15:17 Key Learnings: Apply your measurements to the initial template (Module 4) Draft the back of a 1 dart skirt block How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 7 Drafting Skirt Front (2 Dart) 14:53mins Chapter 1: Side Seam Calculation 04:07 Chapter 2: Dart Calculation 04:59 Chapter 3: Low Hip 10:56 Chapter 4: High Hip 12:56 Key Learnings: Apply your measurements to the initial template (Module 4) Draft the front of a 2 dart skirt block How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 8 Drafting Skirt Back (2 Dart) 27:56mins Chapter 1: Centre Back Dart 00:40 Chapter 2: Side Seam Calculation 05:35 Chapter 3: Dart Calculation 06:12 Chapter 4: Low Hip 14:23 Chapter 5: High Hip 19:32 Key Learnings: Apply your measurements to the initial template (Module 4) Draft the back of a 2 dart skirt block How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 9 Drafting for Fuller Figures 27:00mins Chapter 1: 1 Dart Skirt Block 02:46 Chapter 2: Slanted Waist - Front 03:23 Chapter 3: Side Seam - Front (1 Dart) 08:34 Chapter 4: Slanted Waist - Back 11:03 Chapter 5: Centre Back Dart Length 12:48 Chapter 6: Back Dart Length 13:18 Chapter 7: Side Seam - Back (1 Dart) 14:55 Chapter 8: 2 Dart Skirt Block 19:29 Chapter 9: Dart Distance 20:13 Chapter 10: Side Seam - Front (2 Dart) 21:08 Chapter 11: Side Seam - Back (2 Dart) 24:16 Key Learnings: Understand the differences you can encounter with a fuller figure Learn fuller figure variations for a 1 dart block Learn fuller figure variations for a 2 dart block How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 10 Trace the Draft 33:09mins Chapter 1: Tracing Tips 01:33 Chapter 2: Adding Seam Allowances 08:57 Chapter 3: Front Grainline 12:51 Chapter 4: Hem Allowance 13:26 Chapter 5: Back Grainline 14:10 Chapter 6: Truing Darts 15:52 Chapter 7: Truing Seams 24:11 Chapter 8: Add Notches 31:14 Key Learnings: Learn how to accurately trace a pattern How to true seams and darts Understand how to add seam allowances How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 11 Make Sample 57:19mins Chapter 1: Prepare Fabric 05:04 Chapter 2: Cut out Pattern 08:32 Chapter 3: Marking Fabric 13:27 Chapter 4: Sewing Darts 25:05 Chapter 5: Sewing Seams 38:03 Chapter 6: Stay Stitching 48:40 Key Learnings: Learn how to make a basic sample skirt (toile, calico) Understand what fabric to use for a sample Learn about the grainline on patterns Tips for marking a sample skirt How to stay stitch a sample garment How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 12 Fit Sample 26:36mins Chapter 1: Garment Balance 02:42 Chapter 2: Check Ease 04:05 Chapter 3: Waist Position 06:52 Chapter 4: Side Seam Shape 07:52 Chapter 5: Darts 08:48 Chapter 6: Fitting Person 11:29 Chapter 7: Fitting Fuller Figure 17:50 Chapter 8: Fitting Yourself 19:47 Key Learnings: Learn how to position a sample on a mannequin or a person Understand the main fitting issues that may occur Gain tips for fitting on a mannquin, person and yourself Understand the difference when fitting on a fuller figure How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 13 Pattern Amendments 40:26mins Chapter 1: Side Seam Adjustments 02:52 Chapter 2: Dart Adjustments 14:30 Chapter 3: Waist Adjustment 22:15 Chapter 4: Fuller Figure 27:11 Chapter 5: 2 Dart Adjustment 34:39 Chapter 6: Labelling Pattern 35:23 Key Learnings: Learn how to amend the fitting issues discussed in Module 12 on the paper pattern Understand how to amend the side seams of the pattern How to change the placement and length of the darts at the front and the back Learn how to change the position of the waist at the front and the back Discuss common fitting issues for a fuller figure pattern How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 14 Finalise Block 31:31mins Chapter 1: Truing Pattern 01:42 Chapter 2: Tracing Pattern 06:59 Chapter 3: Labelling 18:15 Chapter 4: Using Pattern Notcher 27:17 Chapter 5: Using Awl 28:01 Key Learnings: Finalise the drafted pattern Understand how to true seams and darts Position the pattern into card Learn how to use a pattern notcher and awl Tips for storing patterns How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 15 Draft a Waistband 39:09mins Chapter 1: Zipper through Waistband 03:39 Chapter 2: Waistband Width 07:41 Chapter 3: Waistband Grainline 10:50 Chapter 4: Waistband with Extension 18:50 Chapter 5: Waistband Extension Single Side 24:34 Chapter 6: Waistband Extension Both Sides 31:34 Chapter 7: Button & Buttonhole Placement 34:02 Key Learnings: Learn how to draft a waistband for your skirt block and other skirt patterns Standard width for waistbands How to draft a straight waistband that the zipper goes through How to draft a straight waistband with an extension Button and buttonhole position How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 16 Draft a Shaped Waistband 29:40mins Chapter 1: Waistband Width 03:00 Chapter 2: Zipper through Waistband 09:58 Chapter 3: Waistband Facing 14:31 Chapter 4: Favouring Facing 15:46 Chapter 5: Waistband with Extension 22:11 Chapter 6: Adjust Skirt for Lower Waist 27:47 Key Learnings: Learn to draft a shaped waistband for the skirt block How to lower the waist of the skirt block Standard waistband widths How to draft a shaped waistband that the zipper goes through How to draft a shaped waistband with an extension Understand favouring for a waistband facing How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 17 Draft a Facing 17:02mins Chapter 1: Facing Width 02:41 Chapter 2: Favouring Facing 07:49 Key Learnings: How to draft a facing for your skirt block or another skirt pattern Standard facing widths Understand favouring for a facing How to Draft a Skirt Block www.madetosew.com © Copyright Made to Sew 2020 Module 18 Draft a Lining 21:41mins Chapter 1: Lining Adjustments 00:46 Chapter 2: Convert Darts to Pleats 02:18 Chapter 3: Adding Ease 02:45 Chapter 4: Ease for a Fuller Figure 04:46 Chapter 5: Lining for a Straight Waistband 05:08 Chapter 6: Loose Lining Hem 05:43 Chapter 7: Lining for Shaped Waistband 11:19 Chapter 8: Lining for Facing 13:31 Chapter 9: Bagged Lining Hem 15:36 Key Learnings:
Load more

Recommended publications
  • Contour Fashion BA (Hons)
    Contour Fashion BA (Hons) Equipment List 2013 BA (Hons) 1. Basic Equipment Basic sewing and pattern cutting equipment is necessary for ALL students undertaking the Contour Fashion BA (Hons) course. You are expected to provide the following basic equipment for yourselves: Pattern master Tape measure French curves Flexi curve and/or flexible 30cm ruler Propelling pencils Black fine felt tip pens Magic tape/Sellotape Eraser Machine Tweezers Pattern Notcher Tracing Wheel Notepads Pattern Awl Scissors (fabric) Scissors (paper) Embroidery scissors Stitch unpicker Cloth marking pencils Designer Fashion Tape Metre Rule Pins and hand sewing needles. You may be familiar with most of the equipment listed above. These can all be purchased from the ‘Morplan’ Student Catalogue 2012 or alternatively go to: www.morplan.com/students . You must allow 7 to 10 working days for delivery so don’t leave ordering your equipment to the last minute! You will also need to purchase a bobbin and bobbin case, for the DMU lockstitch machines, from the DMU Materials Shop on the Mezzanine floor in the Fletcher Tower. To do this you need to purchase a pink card which gives you credit from the same shop. We will give you more information about this when you arrive for Fresher’s Week and this equipment can also be purchased then. Books ‘Pattern Cutting for Lingerie, Beachwear and Leisurewear by Ann Haggar ‘Metric Pattern Cutting’ (Womenswear) by Winifred Aldridge 2. Additional Sewing Equipment It is desirable to have your own domestic sewing machine, because many of the sewing techniques taught can be practised on a domestic sewing machine.
    [Show full text]
  • Blouse, Tie & Dye and Creation of Jawellery
    SESSION:- 2013-2014 {DIPLOMA IN FASHION DESIGNING AND GARMENT TECHNOLOGY} A PROJECT REPORT ON SAREE-BLOUSE, TIE & DYE AND CREATION OF JAWELLERY Under Supervision of: Submitted by: Mr. DINESH KUMAR GAUTAM SWETA JAISWAL Principal Mr. PREM CHANDRA VERMA DEPARTMENT OF FASHION DESIGNING AND GARMENT TECHNOLOGY GOVT. GIRLS POLYTECHNIC, VARANASI PREFACE Fashion Technology viewed as one of the most demanding and professional career of word. It is in this context that Govt. Polytechnic of U.P. began a new trade Named Fashion Technology from 1996 the syllabusas if the course strikes a find balance creativity and individual expression in the one hand commercial and industrial in the other. This course has an opportunity to work with the faculty on exciting constancy project. In this project which is supplement at the paper for the final examination 2013-2014 an attempt has been made to the find a design for saree & jewelry. In this project I have endeavored in the above direction with the local availabele means and resources possibility for better achievement is always there. The great vedic Literature we may guide us in creating new design. Fashion Technology in my view is art of imagination and creation SWETA JAISWAL F.D. & G.T. IIIrd Year Govt. Girls Polytechnic Varanasi CERTIFICATE This is to certify that he dissertation entitled Saree Blouse, Tie & Dye creation of jewelry being submitted by Miss. SWETA JAISWAL Partial fulfillment of the Requirement for the award of Diploma in the Fashion Technology, Submitted to Govt. Girls Polytechnic, Varanasi is a reward of student own work cried by her under my Supervision and guidance, the matter embodied in her dissertation has not been submitted of any other Diploma.
    [Show full text]
  • Sewing Technology
    SYLLABUS OF SEMESTER SYSTEM FOR THE TRADE OF Sewing Technology Under Craftsmen Training Scheme (CTS) (One year/Two Semesters) Redesigned in 2014 By Government of India Ministry of Labour & Employment (DGE&T) J. GENERAL INFORMATION 1. Name of the Trade : Sewing Techno log y 2. NCO Code : 7433.10 3. Duration of craftsmen Training : One year (2 Semesters) th 4. Entry Qualification : Passed 10 class Under 10+2 System of examination 5. Unit Stre ng th 16 trainees 6. Space Norms 64 sq m (4 Sq.m/trainee) 7. Power Norms 05 kw 8. Instructo r's Qualification i. NTC/NAC in sewin technology(earlier trade name as "cutting & sewing") with three years Experience in relevant field Or ii. Diploma in Garment fabricating technology/ costume design with Two yea rs' Experience in relevant field Or iii. Degree in Fashion & apparel Technology With one year experience in relevant field 9. Desirable Qualification : Preference will be given to a candidate With Craft Instructors Training certificate (CITS) in Cutting & Sewing (earlier trade name as "cutting & sewing") Note: Out of two instructors required for the unit 1+1, one must have Degree/Diploma & other must have NTC/NAC qualifications 2 OBJECTI VE OF THE COURSE : To create skilled work force for Self Employment/Working in garment manufacturing Industry as - • Sewing Machine Operator • Assistant to Designer • Assistant worker in Boutique • Sample room designer • Sample Coo rdinator 3 Syllabus for the trade of "Sew ing Technology " under craftsmen training scheme First Semester {Common for Sewing Technology & Dress Designing) Semester code no. : sewing tech. - 01 Duration : Six months - - Week Trade Practical Trade Theory No.
    [Show full text]
  • SKSAMT15 Create a Pattern Via Modelling / Draping
    SKSAMT15 Create a pattern via modelling / draping Overview This standard is for those who develop patterns by draping and modelling cloth using a dress form. The job role may involve: 1 assess a design for draping /modelling suitability 2 drape or model a garment on to a dress form 3 produce a pattern SKSAMT15 Create a pattern via modelling / draping 1 SKSAMT15 Create a pattern via modelling / draping Performance criteria You must be able to: P1 select the appropriate dress form, tools and work aids P2 ensure key land marks are indicated clearly and accurately including P2.1 neck P2.2 waist P2.3 shoulder P2.4 side seams P2.5 princess seam P2.6 hip P3 create a bridge from bust point to bust point if necessary P4 use pins to mark key points such as P4.1 centre bust P4.2 top shoulder P4.3 arm hole depth P4.4 centre of armscye P4.5 centre neck P5 select fabric that is compatible with the intended design, materials and production process P6 measure, cut, and press fabric for modelling P7 mark grain lines, reference lines and pattern information onto fabric P8 pin the fabric to the dress form and position to create the desired effect including P8.1 darts P8.2 tucks P8.3 gathers P9 determine final design and mark the location of seam lines, darts, tucks etc. P10 remove the design from the dress form and lay flat P11 unpin the garment and use rulers and design curves to connect, smooth out and finalise the markings P12 add seam lines and cut off excess fabric P13 re-pin and replace the design onto the dress form P14 check and confirm the fit and
    [Show full text]
  • Table of Contents
    HOW TO START SEWING : ASSEMBIL Table of Contents About Assembil 1 Basic Fabric 20 Introduction 3 Thread 20 Different Ways to Learn 4 Needle Threader 21 How To Use This Book 4 Small Sewing Scissors or Thread Snips 22 Key Methods and Details for Professional Results 5 Fabric Shears 23 The How and Why of Sewing 5 When to Buy New Shears 23 Pins 24 Part 1 Chapter 4 Basic Hand Sewing Exercises 25 Getting Started 7 Exercise 4.01 : Hand Sewing Preparation 26 Exercise 4.02 : Basting (with Large Backstitches) 33 Exercise 4.03 : Running Stitch (with Thread Knots) 38 Chapter 1 An Introduction to Sewing Clothing 9 Chapter 5 The Basic Process 10 Seams and Seam Allowance 43 Design, Pattern, Cut and Sew 10 Joining Fabric to Make Garments 44 What Is a Seam? 44 What Is Seam Allowance (SA)? 44 Chapter 2 What Is a Seam Finish? 44 The Basic Process of Hand Sewing 11 How Much Space is Provided as Seam Allowance? 46 What Is Sewing? 12 Concentrate on Stitching Line 46 The Anatomy of a Needle 12 Seam Allowance Value 46 The Basic Process of Hand Sewing 13 What Is a Stitch? 14 What Are Stitching Lines? 14 Chapter 6 : Equipment and Materials List Elements of Neat Stitching 14 Measure, Mark and Press 47 Correct Fabric / Thread / Needle Combination 14 Tape Measure 48 Correct Support for the Fabric 14 Ruler 48 Securing the Thread in the Fabric 15 Tailor’s Chalk 48 Trimming the Excess Thread 15 Chalk Pencils 49 What Is Tension? 16 Iron and Ironing Board 49 Chapter 3 : Equipment and Materials List Chapter 7 Hand Sewing 17 Hand Sewing a Seam 51 Buying Sewing Equipment
    [Show full text]
  • Suppliers to the Garment Manufacturing Industry 107348 East08 IFC-Welcome:PG 1/5/09 09:30 Page 2
    107348_East08_FC-BC:Pg 1/5/09 09:38 Page FC2 2009 ...suppliers to the garment manufacturing industry 107348_East08_IFC-Welcome:PG 1/5/09 09:30 Page 2 We welcome you to Dear Customer, our teams in Huddersfield… Welcome to the 2009 Eastman Staples catalogue, the “One Stop …here to help you, when you want! Shop” for clothing manufacture. This year’s catalogue has been completely redesigned in a more contemporary manner to reflect a company that is constantly moving forward with the times. Containing products for use from design through cutting to finishing, including many component products and of course the world famous range of Eastman cutting machines. We manufacture a high percentage of the products that we sell which, combined with our bulk purchasing power for the rest of the product range, allows us to be competitively priced whilst maintaining high quality and providing fast response. Established in 1921, Eastman Staples has been a leader in its field for many decades. We are geared up to supply customers from the smallest size up to the largest bulk buying factories located anywhere in the world. Commercial Director I hope that you enjoy looking through our catalogue which with nearly 2,000 products shown will satisfy most requirements, but if there is any item that you cannot see, please do not hesitate to contact us and one of our highly experienced staff members will be happy to source it for you. Colin I Werb Managing Director Sales & Accounts Head Office: Machines Eastman Staples Limited 131 Lockwood Road Huddersfield England HD1 3QW tel: +44 (0) 1484 88 88 88 fax: +44 (0) 1484 88 88 00 email: [email protected] website: www.eastman.co.uk Parts …our UK Nationwide Delivery Fleet Deliveries where you want, when you want… Prices valid at time of going to press and may change without prior notification.
    [Show full text]
  • For Men & Women
    MAKING Click on any image to go to the related material for Men & Women Keyhole Buttonholes Project-Garment Galleries the DVD Video Demos Printable Patterns All content © 2009 by David Page Coffin RTW & Custom Galleries Sources & Links Click Here to launch DPC’s blog for more info about using this DVD Click this symbol to return to this page Click this symbol to go to next page 1 BONUS CHAPTER Using an Eyelet Plate to Make Keyhole Buttonholes Eyelet Plates and Cutters Keyhole buttonholes are designed to An eyelet plate, shown in photos 1 and 2, covers prevent distortion when the closure is your feed dogs and provides a post on which under strain during wear. Without the ex- to position the precut hole for your keyhole, tra space provided by the keyhole shape, plus a slot that allows the needle to make a zig- 2 an ordinary buttonhole will be distorted zag stitch. The post is slotted, too, so the needle as the shank pulls against the end of the can swing inside it to form the inner edge of the hole. On pants, I’d suggest using key- eyelet (photo 3). The black plastic plate in photo holes for any and all buttonholes, wheth- 2 (sitting on top of my Bernina plate) is from my er on button flies, pocket flaps, or waist dear old Pfaff; notice that its slot is oriented in closures. I only recently got a sewing the opposite direction compared to the Bernina machine that could make keyhole but- plate (this apparently makes no difference), and tonholes, but I had already developed a that it has “toes” designed to snap into the feed- way of making keyhole buttonholes with dog holes on the machine, instead of screwing an eyelet plate.
    [Show full text]
  • Metric Pattern Cutting for Women's Wear
    Metric Pattern Cutting for Women’s Wear Also available Metric Pattern Cutting for Children’s Wear Fashion Buying Third Edition Second Edition Winifred Aldrich Helen Goworek 978 06320 5265 3 978 14051 4992 1 Metric Pattern Cutting for Menswear Pattern Cutting for Lingerie, Beachwear and Leisurewear Fourth Edition Second Edition Winifred Aldrich Ann Haggar 978 14051 3141 4 978 14051 1858 3 Fabric, Form and Flat Pattern Cutting The Apparel Industry Second Edition Second Edition Winifred Aldrich Richard M. Jones 978 14051 3620 4 978 14051 3599 3 Pattern Cutting for Women’s Tailored Jackets Fashion Source Book Winifred Aldrich Second Edition 978 06320 5467 1 Kathryn McKelvey 978 14051 2693 9 Fashion Designer’s Handbook for Adobe Illustrator Marianne Centner & Frances Vereker Illustrating Fashion 978 14051 6055 1 Second Edition Kathryn McKelvey & Janine Munslow Introduction to Clothing Manufacture 978 14051 3952 6 Second Edition Gerry Cooklin Carr & Latham’s Technology of Clothing Manufacture 978 06320 5846 4 Fourth Edition Revised by David J. Tyler Careers in Fashion and Textiles 978 14051 6198 5 Helen Goworek 978 14051 1834 7 Metric Pattern Cutting for Women’s Wear Fifth edition Winifred Aldrich © Winifred Aldrich 1976, 1979, 1982, 1985, 1989, 1990, 1994, 1997, 2004, 2008 Blackwell Publishing editorial offi ces: Blackwell Publishing Ltd, 9600 Garsington Road, Oxford OX4 2DQ, UK Tel: +44 (0)1865 776868 Blackwell Publishing Inc., 350 Main Street, Malden, MA 02148-5020, USA Tel: +1 781 388 8250 Blackwell Publishing Asia Pty Ltd, 550 Swanston Street, Carlton, Victoria 3053, Australia Tel: +61 (0)3 8359 1011 The right of the Author to be identifi ed as the Author of this Work has been asserted in accordance with the Copyright, Designs and Patents Act 1988.
    [Show full text]
  • Packaging of Competency Standards for National Qualification
    Occupational Standards for Caribbean Vocational Qualifications (CVQ) CCGPAMT0301 CVQ Level 3 – APPAREL MANUFACTURING TECHNOLOGY Unit Number Unit Title Requirement U58603 Construct and adapt patterns to customer requirements Mandatory U58703 Lay-up, mark-in and cut materials Mandatory U58803 Produce sample garments for manufacture Mandatory U58903 Handle and measure garments Mandatory U59003 Resolve quality issues and provide technical feedback Mandatory U59103 Plan apparel production schedule Mandatory U59203 Produce final apparel production schedule Mandatory U59303 Generate electronic patterns Mandatory U59403 Illustrate fashion design concept Mandatory U59503 Develop and grade garment pattern Mandatory U59603 Generate cutting lay plans Mandatory U59703 Create garment specifications and monitor product life cyle Mandatory U59803 Maintain a clean and safe work area Mandatory U59903 Provide leadership for your team Mandatory U60003 Develop and monitor operational plans Mandatory U60103 Manage professional relationship and develop yourself To obtain a Caribbean Vocational Qualification (CVQ) all Mandatory Units must be achieved. Legend to Qualification code CCGPAMT0301 CARICOM Code Occupational Number Sector Qualification Level Occupational Area Key: CC – CARICOM; GP – Garment Production; AMT - Apparel Manufacturing Technology; 3 - Level 3; 01 - Numerical sequence Approved @ 2016 Caribbean Community (CARICOM) Legend to Unit Code Example: U58603 U58603 Unit Unit Number Qualification level Key: U – Unit; 612 – Unit #: 03 – Qualification level Approved @ 2016 Caribbean Community (CARICOM) ACKNOWLEDGEMENTS The Technical and Vocational Education and Training Council would like to thank the following for their contribution to the development of this document: Creative Skill Set: www.standards.creativeskillset.org National Occupational Standards: Scottish Qualification Authority Members of the Apparel Manufacturing Technology Working Group Ms. Joy Prime Samuel Jackman Prescod Polytechnic Ms.
    [Show full text]
  • FAB-212 Flat Patternmaking II
    BERGEN COMMUNITY COLLEGE BUSINESS, ARTS & SOCIAL SCIENCES Fashion Apparel Design (FAB) Departmental Policy Syllabus FAB-212 Flat Pattern Design II Course & Section: Instructor: Credits: 3 | Lecture [2.00], Laboratory [2.00] Email: Pre/Co-requisites: FAB-112 Office Hours: Classroom: Co-requisites: FAB-213 COURSE DESCRIPTION This course builds on FAB-112, providing students with more advanced flat patternmaking techniques. Students develop sloper variations including the two-piece sleeve, jacket and pleated pants slopers. STUDENT LEARNING OUTCOMES After successfully completing all course activities, the student will be able to: 1) Develop the jacket sloper with sleeves, and the sleeveless dress sloper. 2) Develop complex sleeve variations including kimono, dolman sleevesand fitted dropped shoulder sleeve. 3) Draft pleated pants and jean. 4) Demonstrate how to incorporate stretch and knits into pattern development. MEANS OF ASSESSMENT Students will be assessed through a variety of methods, including: 1) Tests 2) Assignments 3) Journal 4) Final Project REQUIRED TEXTBOOK & RESOURCES Armstrong, Helen Joseph; Pattern Making for Fashion Design, 5 Ed, Harper Collins, New York, 2005. ISBN-13: 978-0136069348 Kopp, Rolfo & Zelin; How to Draft Basic Patterns, 3 Ed, Fairchild, 1984. ISBN-13: 978-0870054679 Gross, Kopp, Rolfo & Zelin; Designing Apparel Through the Flat Pattern, 6 Ed, Fairchild, 1991. ISBN-13: 978-0870057373 STUDENT SUPPLIES Pattern Paper Oaktag Carbon Paper Muslin in Variety of Weights as Required Hip Curve Armhole Curve L Ruler Clear Plastic Ruler Measuring Tape Tailors Chalk Paper Scissors Fabric Scissors Pattern notcher Hand Sewing Needles Straight Pins Soft and Hard Drawing Pencils Pencil Sharpener Narrow Black Twill Tape Narrow Sharpies in Red, Black and Blue SUGGESTED RESOURCES UniversityOfFashion.com WGSN.com Asapofga.com Assist-intl.com Cutplan.com Fabricad.com GGT.com Handford, Jack, Professional Pattermnaking for Designers, Plycon Press, California, 1984.
    [Show full text]
  • LMT00 Textiles, Clothing and Footwear Training Package
    LMT00 Textiles, Clothing and Footwear Training Package Volume 6 of 19 Clothing Production Version Number: 3 Review Date: June 2009 Textiles Clothing and Footwear Training Package LMT00 Version 3 © Commonwealth of Australia 2005 This work has been produced with the assistance of funding provided by the Commonwealth Government through Department of Education Science and Training (DEST). An individual may make a photocopy of all or part of the work for their personal use. A Registered Training Organisation may make photocopies of all or part of the work for the teaching purposes of that organisation, including for supply to its students provided that any consideration does not exceed the marginal cost of preparation, reproduction, assembly and delivery. Except as permitted under the Copyright Act 1968, all other rights are reserved. Requests for permission may be directed to: Branch Manager, Technology and Information Services Branch, Industry Skills Development Group, Department of Education, Science and Training, GPO Box 9880 Canberra City, ACT, 2601. Website: www.dest.gov.au This work is the result of wide consultations with Australian industry participants. It is a collaborative view and does not necessarily represent the view of DEST or any specific body. For the sake of brevity it may omit factors which could be pertinent in particular cases. While care has been taken in the preparation of this Training Package, DEST and the original developer do not warrant that any licensing or registration requirements specified here are either complete or up-to-date for your State or Territory. DEST and the original developer do not accept any liability for any damage or loss (including indirect and consequential loss) incurred by any person as a result of relying on the information contained in this Training Package.
    [Show full text]
  • Sewing Technology
    COMPETENCY BASED CURRICULUM FOR THE TRADE OF Sewing Technology SEMESTER-I & II UNDER CRAFTSMAN TRAINING SCHEME (CTS) IN SEMESTER PATTERN BY GOVERNMENT OF INDIA MINISTRY OF SKILL DEVELOPMENT& ENTREPRENEURSHIP DIRECTORATE GENERAL OF TRAINING 1 CONTENTS Sl. Topics Page No. No. 01 Introduction 02 General Information 03 Course Structure 04 Job Roles 4.1 Brief Description 4.2 NOS & QP/NCO Mapping 05 NSQF Level Compliance 06 General Training Plan, Examination & Pass regulation 07 Learning Outcomes 08 Assessable Outcomes with Assessment Criteria 09 Syllabus Content with Time Structure 9.1 9.1 Syllabus content for Professional Skill & Knowledge 9.2 9.2 Syllabus Content of Core Skills 10 Employability Skills 10.1 General Information 10.2 Distribution of Topics Between Semesters for Employability Skills 10.3 Syllabus Content of Employability Skill 11 Infrastructure 12 Assessment Standard 12.1 Assessment Guideline 12.2 Internal Assessments (Formative Assessment) 12.3 Final Assessment- All India Trade Test (Summative Assessment) 13 List of Tools & Equipment-Annexure I 14 Guidelines for Instructors and Paper Setters- Annexure II 15 List of Trade Committee Members 2 1. INTRODUCTION India is one of the youngest nations in the world. Our youth are our strength. However, a challenge facing the country is that of skilling our youth as per the demands of the industry. Recognizing the need for quickly coordinating the skill development and entrepreneurship efforts of all concerned stakeholders, the Government of India created the Ministry of Skill Development and Entrepreneurship on 9th November, 2014. To create further convergence between the Vocational Training System through Industrial Training Institutes (ITIs) and the new skill initiatives of the Government, the Training and Apprenticeship Training divisions from the Directorate General of Employment and Training (DGET) under the Ministry of Labour and Employment stand transferred to the Ministry of Skill Development and Entrepreneurship (MSDE) with effect from 16th April, 2015.
    [Show full text]