1-800-543-6915 www.childrenscornerpatterns.com

Robert Vintage Classic styles also matter when you put little ones to bed. Now that our Robert pattern is available in a wider range of sizes, you can make these vintage pajamas for all your little ladies and gents.

Supplies Robert Children’s Corner pattern Piping – 3 yards Tracing Paper Notions per the pattern Fabric Requirements (in yards)

Sizes 6m-24mo 3-6 7-8 10-14

7 1 3 45" wide 1 /8 2 /4 3 3 /8

7 1 5 3 54/60" wide 1 /8 2 /4 2 /8 2 /4

Cutting Instructions 1. Trace front using tracing paper starting and stopping at fold line. Measure ¼” over from the fold line toward the , and draw a line parallel to the fold line. Connect this line to the and the . This is your new shirt front pattern piece.

Cutting Layout

aamas

old ine 45/54 wide sies 6mo-6 old

hirt ac ollar ocet odiied ants ront asitand ocet

odiied hirt ront hirt on leee

ants ants odiied ants ac acin

elae

45 wide sies -14 2. Place tracing paper on the original shirt front again, old ocet ollar acin and measure ¼” from the fold line toward the shirt hirt ac odiied asitand hirt ront ocet front. Draw a line parallel to the fold line. Continue ants ants on leee

tracing the front facing. This piece should be 1 ½” hirt odiied ants ront wide. This is your new facing piece. odiied ants ac

elae 54/60 wide sies -14 old

ollar hirt ac odiied asitand on leee hirt ront ocet

ocet ants acin hirt hirt

odiied ants ac odiied ants ront

elae

12/2018 1 3. For the main part of the , measure down ¾” from the fold line, draw a line, and trace the lower part of the pocket. For the pocket , measure down 1” from the fold line, and draw a line, and trace the part of the pocket. Cut one piece of piping the same width as the main pocket. Trim piping allowance to ¼”.

ocet old ine old ine ew ttin ine ew ttin ine

ain ocet

4. For pants front and back, fold up the bottom of the pattern pieces ¼” below the fold line at hem to account for the added cuff. 3. Trim piping seam allowance to ¼”. Stitch piping to the right side of the shirt front starting 1/8” 5. For the shirt cuff, do not use the pattern piece before the center front line. Pivot at the corner and provided. Instead, cut two rectangles of fabric 12” continue down the front of the shirt (on the right- long by the width in the table below for your size. hand side for girls, left-hand side for boys). Clip Cut two pieces of piping the same length. Trim seam allowance at corner diagonally. piping seam allowance to ¼”. Do not use the shirt

6m-24mo 3-6 7-14 Shirt cuff 1 3" 4" 4 /2" width to cut

cuff in the pattern.

6. For the pants cuff, cut two rectangles of fabric 3” wide by 15” long. Cut two pieces of piping the same length. Trim piping seam allowance to ¼”. 4. Stitch piping on the other front edge the same way but stopping and easing piping off the edge at the 7. Cut these and the remaining pieces according third . to pattern instructions using the cutting layout provided. 5. Place facing on shirt with right sides together. Stitch in place starting at center front, pivot, and stitch down front edge following stitching from Shirt Construction piping. Clip seam as shown in step #8. Trim corner 1. Follow steps #1-3. diagonally. Turn right side out.

2. Stitch piping to the top edge of the main pocket piece. Stitch the pocket cuff to the pocket with right sides together and following the stitching line from the piping. Press seams toward main pocket. Complete the pocket construction according to the pattern.

2 Robert Vintage Pajamas www.childrenscornerpatterns.com 6. Cut one piece of piping to fit the outside edge of the . Trim piping seam allowance to ¼”. Stitch piping to the top collar pivoting at corners. Pull ½” of the cording on each side, and trim the cording to

reduce bulk.

7. Follow steps #9-13 and 15.

8. For long , skip steps #16-20. Fold shirt cuff, fold in half with wrong sides together. Stitch piping to raw edge of folded cuff. Pull 1/4” of the cording on each side, and trim the cording to reduce bulk.

9. Place cuff on bottom edge of sleeve with right sides together and piping between. Stitch cuff to sleeve following stitching from piping. Finish seam, and press toward sleeve. Trim excess cuff.

cording to reduce bulk. 10. Finish sleeve with step #21. Skip the remainder of the sleeve cuff instructions. 3. Place cuff on bottom edge of pants with right sides together and piping between. Stitch cuff to pants 11. Continue with the Robert shirt instructions at step following stitching from piping. Finish seam, and #30. Remember to sew your on the press toward pants. Trim excess cuff. same side with the piping down the entire front of the shirt. The are sewn to the side with the 4. Stitch inseam with right sides together, matching piping stopping at the third buttonhole. center front and back seams and cuff seams. Finish seam, and press to back. Pants Construction 5. Finish pants following steps #16-19. 1. Follow steps #1-9 for the pants. We made our pants unlined and without .

2. Fold pants cuff, fold in half with wrong sides together. Stitch piping to raw edge of folded cuff. Instructions by Pull 1/4” of the cording on each side, and trim the Susan Whitman

3 Robert Vintage Pajamas www.childrenscornerpatterns.com