2004 Turbo® Sport Cyclocomputer

2004 TURBO® SPORT CYCLOCOMPUTER

Congratulations on your purchase! You are now the owner of one of the world’s most advanced cyclocomput- ers. Your Specialized Turbo® Sport a revolutionary new three-line LCD screen. The large, easy to read, digits allow you to view two functions simultaneously and the alphanumeric dot matrix display provides a quick reference to the currently displayed function. The Turbo® Sport has been designed to provide the best combina- tion of performance, features, durability and ease of use.

3 7

4 5

8 6

2 1

FIGURE 1

This illustration describes the screen display and buttons MODE/SET rocker switch Dot-matrix Display Area Digital Display Area Wheel Option Indicator MPH or KM/H indicator

1 The following 7 functions 31.8mm mounting are available on your bracket (1) Turbo® Sport: Wired Speed sensor (1) SPEED – Current Speed Magnet with screw (1) AVSPD – Average speed Adhesive backed MXSPD – Maximum Speed magnet (1) TRIP – Trip Distance Cable tie wraps (5) ODO – Odometer (total Mounting bracket sizing distance) straps (3) ATM – Automatic Start/Timer FIGURE 2 CLOCK – Digital 12/24 Hour Clock Battery Installation and replacement- FIGURE 2 Before using your Turbo® This computer Sport Computer you will also features: need to install the battery. Wired speed sensing Turn the computer over so bottom of the case with the The Turbo® Sport wired Two function LCD Display the display is facing down- tip of a pen or a paper speed sensor can mount on Second Wheel Option ward. Use a coin to clip. This will clear all the the right or the left side of Easy Calibration Mode unthread the battery cap data and re-start the the fork blade. Use the Water resistant housing from the Computer. Install Computer. If you need to

2 Year Warranty the battery (model replace the battery, make a 4 screws CR2032, Specialized P/N note of your odometer 481-3004) with the posi- reading and wheel circum- CR2032 battery THE FOLLOWING tive pole (+) facing ference settings before ITEMS ARE INCLUDED upward. Carefully thread removing it. You can then Rubber O-ring IN YOUR TURBO® the battery cap back onto re-enter the data when you SPORT PACKAGE: the case with a coin. (See restart the Computer. Turbo® Computer Figure 3) If, after battery CR-2032 Lithium Battery replacement, the LCD dis- FIGURE 3: BATTERY (1) play is blank or shows INSTALLATION Tightening Battery Door (1) incomplete digits, turn the sequence 26.0mm mounting Computer over and press Mounting the Turbo® FIGURE 3 bracket (1) the “AC” button on the Sport: 2 3 cable tie-wraps provided to clean the spoke that you up when wheel speed is position the sensor. Do not plan to attach the magnet detected or when the tighten until the final place- to. Remove the backing MODE or SET button is ment of the sensor magnet from the adhesive tape and pressed. In order to oper- is correct. (See figure 4). firmly press the magnet ate your computer it must Wheel magnets have been onto spoke. The tape uses be placed in various FIGURE 6 provided for both tradition- a special pressure sensitive “modes” (i.e. odometer al round adhesive. To ensure a mode, distance mode). The spokes and strong bond, please wait at To test for proper installa- computer can be cycled bladed (flat) least 12 hours for the tion of the magnet, trans- through these modes by aerodynamic adhesive to cure before mitter and Computer, acti- pressing the “MODE” but- spokes. riding your bicycle. vate the Computer by push- ton located on the right- ing the ‘MODE’ (right side) hand side the MODE/SET Attach the Attach the appropriate button. Pick up the front of rocker switch. There are magnet to a FIGURE 4 mount (26.0mm and the bicycle and spin the six cycling modes avail- spoke across 31.8mm sizes are includ- front wheel. The “wheel able: 1) Clock Mode, 2) from the transmitter with ed) to the handlebar using option” indicator will flash. Odometer Mode, 3) Trip the magnet screw. The the bracket screw provid- If it does not flash, check Distance Mode 4) Average clearance between the ed. Tighten so that the the sensor and magnet Speed Mode, 5) Maximum magnet and the transmitter bracket cannot rotate on alignment. Realign as nec- Speed Mode, 6) Automatic should be approximately the handlebar. There are essary until the “wheel Timer Mode. Once you 1/32”-1/16” several sizing straps pro- option” indicator flashes familiarize yourself with (1-2mm). vided to fit different diame- while spinning the wheel the mode operation you Tighten the mag- ter bars. (See figure 6). will find it very easy to net and transmit- Slide the Computer for- navigate. The following ter. Do not over- ward onto the mount until OPERATION AND flowchart outlines the tighten the mag- it ‘snaps’ into place with PROGRAMMING mode sequence. Once a net screw. (See an audible click. Plug the When your Turbo® Comp particular mode has been figure 5). wire from the speed sensor has not detected any speed entered, its values can be FIGURE 5 into the socket on the bot- input for 30 minutes, it will reset or adjusted by press- For wheels with tom of your Computer To enter sleep-mode in order ing and holding the “SET ” bladed spokes: remove the Computer, to conserve battery power. button for three seconds. Use some isopropyl (rub- remove the speed wire During sleep mode only the bing) alcohol or a mild then push it backward until digital clock is displayed. detergent to thoroughly it releases from the mount. The computer will wake it 1. Setting the 4 5 play language mode. odometer setting is correct CLOCK I push the “SET” button five (Note: The “MODE” button ODO times to exit odometer may be held to quickly I 2. Miles or Kilometers mode. (Otherwise, see scroll to the correct digit.) TRIP I selection: “Setting the programmable Press the “SET” button to AVSPD Your Turbo® Sport will odometer” below). select the next digit to the I record distance and speed right. Repeat this process MXSPD I in either miles (m & m/h) until all five digits are ATM or kilometers (K & Km/h). 3. Setting the entered as your existing Please note that miles can Programmable Odometer: mileage. (See figure 7) Display Language only be selected when the This mode is useful if you Your Turbo® can display language setting is English. have replaced the battery information on the dot- All other languages display and would like to retain the 4. Wheel Circumference matrix display area in six only kilometers. (See mileage you have already different languages: “Setting the Display ridden. To access the English (ENGL), German Language” above). To Programmable odometer (GER), French (FR), Italian enter your selection of mode, first advance to the (ITA), Dutch (NED), and miles or kilometers, push Odometer Mode by press- Spanish (ESP). To select the “MODE” button until ing “MODE” button until your language push the ODO appears in the Dot- ODO appears in the Dot- mode button repeatedly matrix Display Area (This matrix Display Area. Hold until CLOCK is displayed in is called the odometer down the “SET” button for the Dot-matrix Display mode). Next, hold down three seconds (If you have Area. Then, depress hold the “SET” button for three selected English language, the “MODE” button for seconds. The “Km” or “m” the Km/h indicator will FIGURE 7 three seconds. The selected indicator will begin blink- flash. If the Km/h setting is Selection: language will be dis- ing. You may now alter- correct press the “SET” but- To set the circumference for played. Use the “MODE” nate between miles and ton once) and a five-digit the type of tires you are button to scroll through the kilometers by pressing the number will appear. You using, you can use languages. When the “MODE” button. When the are now in the program- Specialized’s “Easy selected language is dis- correct choice is flashing, mable odometer mode. To Calibration Mode” or played (default language is select it by pressing the enter a mileage into the measure your actual tire English), press the “SET” “SET” button. You will now odometer, press the circumference by the roll- button once to confirm enter the “Programmable “MODE” button until the out method. Two different your selection and exit dis- Odometer” mode. If the flashing digit is correct. tire diameters may be 6 7 entered by using the now show the currently rider weight. Generic Tire Size Chart Computer’s “Second selected tire size for wheel This chart is for non- Wheel Option.” option #1. To scroll through 1. Extend a tape measure Specialized tires the preprogrammed tire out to 3000mm (120 inch- 26 X 1.75 sizes press the “MODE” es) and lock it in place. 2140 Easy Calibration Mode: button. When you reach 2. With your tire inflated to 26 X 2.0 Your Turbo® Sport has the desired tire size press its proper pressure, place 2074 been preprogrammed with the “SET” button once to the valve at the 6:00 posi- 26 X 2.1 the following 14 select it and enter Easy tion (at the bottom) directly 2090 Specialized tire sizes: Calibration Mode for wheel over the start of the meas- 650C X 20 26 X 1.0 option #2. Follow the same uring tape. 1945 26 X 2.2 procedure to program the 3. Roll the wheel one com- 700C X 26 26 X 1.25 wheel #2 tire size and tap plete revolution until the 2124 650c X 20 the “SET” button to exit valve stem is again at the 700C X 38 26 X 1.5 Easy Calibration Mode. 6:00 position. Read the 2170 700c X 20 tape directly under the 26 X 1.9 Roll Out Method valve and note the distance Programming 700c X 23 The roll out method will in millimeters. (To convert the circumference: 26 X 1.95 inches to millimeters, multi- To enter the tire circumfer- 700c X 26 ply inches by 25.4). Use ence number, select the 26 X 2.0 this number to replace the Odometer (ODO) mode 700c X 32 default (default values are and then hold down the 26 X 2.1 2073 for wheel one, and “MODE” button for three 700c X 38 2134 for wheel two) when seconds. The display will When using Easy programming your now show the currently Calibration Mode, the Computer. (See figure 9). selected tire size for wheel Turbo® Sport will display You may also use option #1. (See figure 10). the tire size on its LCD dis- the following quick- If necessary scroll through play screen. (See figure 8) reference chart: the preprogrammed tire FIGURE 8 The Easy Calibration Mode sizes by tapping the is accessed by entering the provide the most accurate Roll Forward “MODE” button until the Odometer (ODO) mode Computer calibration and stem display shows MM and and holding down the can take into account vari- four-digit number. This “MODE” button for three ables such as inflation number represents your Wheel Circumfrence seconds. The display will pressure, rim width and tire circumference in mil- 8 FIGURE 9 9 limeters. Press the 5. Setting the Clock Press the “SET” button to displayed up to 99.9 M/h “MODE” button until the Your Turbo® Sport features accept the hour selection. (99.9 Km/h) with a resolu- flashing digit is correct. a digital clock. To access The minutes will flash and tion of 0.1 M/h (0.1 (Note: The “MODE” but- the “clock mode” press can be adjusted by press- Km/h) ton may be held to scroll and the “MODE” button ing the “MODE” button. to the correct digit.) Press repeatedly until CLOCK (Hold the “MODE” button the “SET” button to select appears in the Dot-matrix to scroll through the digits Average Speed (AVSPD)- the next digit to the right. Display Area. To set the quickly) Press the “SET” The Average Speed is Repeat the process until clock, press the “SET” but- button to set the minutes shown on the lower line all four digits are entered ton for three seconds. The and return to clock mode Digital Display Area up to as your tire circumference. display will flash either 99.9 M/h (99.9 Km/h) Press the “SET” button twelve (12:) or twenty four with a resolution of 0.1 once to select it and enter (24:). Select between 12: 6. AutomaticTimer Mode M/h (0.1 Km/h) the circumference for or 24: mode by pressing The Turbo® Sport has an The average speed is wheel option #2. Follow the “MODE” button. Press Automatic Timer Mode based upon the ATM time. the same procedure to the “SET” button to confirm (ATM) The ATM selection The resolution of the aver- program the wheel #2 tire your selection. The hour allows you to keep track of age speed data on the size and tap the “SET” digit will now begin flash- your actual riding time. Digital Display Area is button to exit circumfer- ing. Press the “MODE” The ATM timer only oper- shown in 0.1M/h or Km/h ence programming mode. ates when the wheel is rotating and cannot be turned on or off manually. Note: The average speed (AVSPD) calculation is based upon the ATM time.

COMPUTER FUNCTIONS

Speedometer (SPEED)- FIGURE 11 Your current speed is FIGURE 12 button to adjust the hour always displayed in large digits. AM/PM is selected digits on the top line of the increments. (See figure 12) FIGURE 10 by scrolling the hour digit. LCD screen. The speed is 10 11 Maximum Speed operates only when there is Odometer (ODO)- Turbo® Sport is capable of (MXSPD)- speed input and is dis- The odometer will record storing two tire sizes. You The Maximum Speed is played In the Digital the total distance traveled can change between the shown on the lower line of Display Area of the screen up to 99,999 miles or kilo- two sizes by entering the Digital Display Area up meters and then roll to Distance Mode and select- to 99.9 M/h (99.9 Km/h) zero. The odometer can be ing TRIP. Then, press the with a resolution of 0.1 Trip Distance (DST)- reset by pressing the “SET” “MODE” button for three M/h (0.1 Km/h) The max- Trip distance mode will button for three seconds. seconds. The second wheel imum speed is retained in record up to 999.99 miles The total distance is shown mode indicator will change memory and updated or kilometers and then roll on the lower line if the from 1 to 2. Mileage when a higher speed is to zero. The trip distance screen. recorded will be cumulative maintained for three sec- can be reset by pressing between the two sizes. (An onds. The maximum speed the “SET” button for three accessory handlebar mount can be reset by pressing seconds. The resolution is Programmable Odometer- is available from your the “SET” button for three 0.01 miles (0.01 The odometer digits are Specialized dealer. P/N seconds. (See figure 13) Kilometers). The trip dis- programmable. This is 4814-5045 tance is shown on the convenient for transferring lower line if the screen. your hard-earned mileage that is usually lost when TROUBLESHOOTING: changing batteries or Display is blank: Computers. Change the battery or press the AC button on the bottom of the case Clock- Display shows Your Turbo® Sport is partial digits: equipped with a digital Press the AC button on the clock. The clock can be set bottom of the case. FIGURE 13 to operate in either 12 or Speed/distance not record- 24-hour mode. ing: Check sensor/magnet alignment. Make sure that FIGURE 14 Auto Start/Stop Timer Second Wheel Option- the sensor is no more than (ATM)- In ATM mode the For riders who own more 1/16” (2mm) from the timer function records the than one bicycle or who magnet. Replace transmit- actual time spent riding. It frequently change tires, the ter battery if necessary. 12 13 Recalibrate Computer and regularly. If any of the S-store online at transmitter. components come loose, it Trip Distance (DST) WWW.SPECIALIZED.COM Entire screen is dark: could become tangled in 0 to 999.99 miles or Km Did you leave the bike your spokes and cause an DESCRIPTION PART# parked in the hot direct accident. Odometer (ODO) STANDARD WHEEL sun when it was parked? If • See your authorized 0 to 99,999 miles or Km MAGNET 480-3003 so, move the bike to the Specialized dealer if you CR-2032 TURBO® shade. The data will be have any trouble installing Stopwatch (TM) BATTERY 480-3004 OK. or maintaining your 0 to 9hrs, 59min, 59sec. ADHESIVE BACKED Computer moves Computer. recycling type WHEEL MAGNET on handlebar: • Clean the unit with a 4800-3002 Tighten mount or add siz- mild detergent and a soft Automatic Timer (ATM) CENTER MOUNT ing straps to improve fit on dry cloth. Never use any 0 to 9hrs, 59min, 59sec. 4814-5035 handlebar. kind of solvent or alcohol. recycling type TURBO SPORT/COMP • The Turbo® Sport 2ND BIKE KIT 4814-5045 IMPORTANT! Computer is intended for Interval Timer (INT) TURBO SPORT/COMP • Pay attention to traffic use on bicycles only and 5 seconds to 9hrs, 59 SENSOR WIRE and road conditions at all should not be used on any min, 59 sec. 4814-5055 times. Your first obligation motorized vehicle. TURBO MOUNT ONLY is to be attentive and to Distance 26.0MM 4814-5060 ride safely. SPECIFICATIONS: Countdown(DISTÚ) TURBO MOUNT ONLY • Do not expose it to direct Current Speed: .01 to 999.99Miles 31.8MM 4814-5065 sunlight except when you 0.0 to 99.90 MPH are riding. .01 to 999.99Kilometers • Do not disassemble you 0.0 to 99.90 Km/H Turbo®. There are no user Operating Temperature serviceable parts inside. Average Speed (AVS) 40°F to 104°F (4°C to Two Year Limited • Make sure the magnet 0.0 to 199.9 MPH 40°C) Warranty: and the transmitter are well Specialized Bicycle Components Inc. warrants the Original aligned. Check them regu- 0.0 to 199.9 Km/H Purchaser of this Specialized® larly. The following replacement Turbo® Sport cyclocomputer that • Keep the Computer and Maximum Speed (MXS) parts are available from the product is free from defects of all of its components tightly 0.0 to 199.9 MPH your Specialized dealer or material and workmanship under normal use and service for a peri- attached, and check them to 199.9 Km/H by visiting the Specialized od of two (2) years from the date 14 15 of the original purchase. If within authorized to assume any liability two (2) year from the date of that on behalf of Specialized Bicycle original purchase, this product is Components, Inc. in connection found to be defective in material or with the sale of this product. Some workmanship under normal use or states do not allow the exclusion or service, Specialized Bicycle limitation of incidental or conse- Components Inc. will, at its sole quential damages or limitations on option, repair or replace the prod- how long an implied warranty uct without charge; provided that lasts, so the above limitation or the Original Purchaser returns the exclusion may not apply to you. product, securely packaged, This warranty gives you specific postage prepaid to: Specialized legal rights, and you may also Bicycle Components Inc., 1137 have other rights which vary from South, 3800 West Salt Lake City, state to state. UT 84104, USA. Attn: Turbo® Sport Warranty. Be sure to include a letter indicating the specific rea- Turbo® is a registered trade- sons for returning the product and mark of Specialized Bicycle proof of date of purchase. Components Inc. This warranty does not apply to, © 2003 Specialized Bicycle and is void as to, defects or physi- Components Inc. cal damage resulting from abuse, WWW.SPECIALIZED.COM neglect, improper repair, improper fit, alterations, modifications or use contrary to that intended by the manufacturer. Except to the extent prohibited by applicable law, any implied warranty of mer- chantability or fitness for a particular use or purpose is limited in duration of this limited warranty. Specialized Bicycle Sportonents, Inc. shall not be liable for any acci- dental or consequential damages arising from any breach of any expressed or implied warranty on this product. This warranty is exclusive and in lieu of all other warranties, expressed or implied, and all other remedies, guaranties or liabilities arising by law or otherwise. Note: This warranty does not per- tain to batteries. No person or representative is