Hr-P94k/P54a
Total Page:16
File Type:pdf, Size:1020Kb
INSTRUCTIONS 3 Precautions 4 Controls English The rating plate and the safety caution are on the rear of the unit. Front panel Front panel WARNING: DANGEROUS VOLTAGE IN-SIDE 1 STANDBY/ON button WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO To turn the power on and off (standby mode). RAIN OR MOISTURE. Hi-Fi KARAOKE MULTI 6HEAD 2 Cassette loading slot STANDBY/ON TAPE POSITION ON SCREEN AUTO VOLTAGE B.E.S.T. PICTURE Load the video cassette here. The STANDBY/ON button does not completely shut off mains power from the unit, Hi-Fi Karaoke MULTI SYSTEM 1 MIC 2 PAL/MESECAM/NTSC3.58/4.43 3 1 but switches operating current on and off. NTSC PLAYBACK ON PAL TV 3 Rewind 1 button VIDEO CASSETTE PLAYER SUPER PAL NTSC POWER-ON STANDBY/REC OSD SP/LP/EP HEAD CLEANER VIDEO CASSETTE PLAYER HR-P94K To rewind the video tape and to start reverse shuttle search playback mode. HR-P94K 4 Play # button This unit is produced to comply with Standard IEC 60065. To start playback. 5 Fast forward ¡ button HR-P94K/P54A When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space To fast forward the video tape and to start forward shuttle search playback mode. on all sides to allow for ventilation (10 cm or more on both side, on top and at the rear.) 6 SP / LP / EP button When discarding batteries, environmental problems must be considered and the local rules To select the recording tape speed. or laws governing the disposal of these batteries must be followed strictly. Thank you for purchasing this JVC video cassette player. To ensure optimum performance Hi-Fi KARAOKE MULTI 6HEAD 7 § LONGPLAY RECORDING AUTO VOLTAGE B.E.S.T. PICTURE Stop/Eject button STANDBY/ON of this unit, please read this instruction manual thoroughly. Failure to heed the following precautions may result in damage to the player, remote To stop playback and to eject the video tape. MULTI SYSTEM control or video cassette player. PAL/MESECAM/NTSC3.58/4.43 NTSC PLAYBACK ON PAL TV 8 Record ¶ button SUPER POWER-ON STANDBY/REC PAL NTSC OSD SP/LP/EP 1. DO NOT place the player . HEAD CLEANER VIDEO CASSETTE PLAYER HR-P54A To start recording. Features Automatic features ... in an environment prone to extreme temperatures or humidity. HR-P54A 1 2 ... in direct sunlight. 9 OSD button • 3 system (PAL/MESECAM/NTSC) Auto power on ... in a dusty environment. To display the information on the television's display. • The video cassette player is automatically NTSC playback (on PAL television) ... in an environment where strong magnetic fields are generated. 0 Remote sensor window • turned on when the tape is inserted. RF output G/K switchable ... on a surface that is unstable or subject to vibration. For remote control operation. • Digital auto tracking 2. DO NOT block the player's ventilation openings or holes. Rear panel Auto rewind ! • HQ (High Quality) The video tape is automatically rewound (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may STANDBY / REC indicator • Auto playback function when the end of the tape is reached during not be able to get out.) • Lights when the power turns off (Standby mode) or during recording mode. • Repeat playback the play, recording or shuttle search forward 3. DO NOT place heavy objects on the player or remote control. • Blinks during recording pause mode. • 4. DO NOT place anything which might spill on top of the player or remote control. RF OUT Shuttle search mode. IN OUT @ R POWER-ON indicator • If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.) Still and slow motion Auto playback AUDIO L Lights when the power turns on. • 5. DO NOT expose the apparatus to dripping or splashing. ANT.IN Line recording If the video cassette’s safety tab has been VIDEO # MIC input terminals (HR-P94K only) • Karaoke (HR-P94K only) removed, playback will begin automatically 6. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place HR-P94K • B.E.S.T. (Biconditional Equalized Signal when the tape is inserted into the video any containers filled with water or liquids (such as cosmetics or medicines, flower vases, Tracking) picture system cassette player. potted plants, cups, etc.) on top of this unit. Rear panel 7. DO NOT place any naked flame sources, such as lighted candles, on the apparatus. 1 Power off eject 8. AVOID violent shocks to the player during transport. AC power cord Even when the video cassette player’s 2 power is off, pressing the eject button will Beware of moisture condensation RF. OUT terminal Moisture in the air will condense on the VCP when you move it from a cold place to a warm turn the power on and eject the tape. Once 3 AUDIO/VIDEO IN terminals ejected, the power will be turned off again place, or under extremely humid conditions — just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to 4 automatically. RF OUT AUDIO/VIDEO OUT terminals the tape. In conditions where condensation may occur, keep the VCP’s power turned on for IN OUT Auto head cleaning AUDIO 5 a few hours to let the moisture dry. L ANT. IN terminal ANT.IN When a tape is loaded or ejected the VCP VIDEO video head is cleaned automatically. When transporting ∗ The video cassette player illustrations appearing in this instruction manual are of the HR-P94K. PAL NTSC 7 Be sure to remove cassette from VCP before packing. HR-P54A 7 Only cassettes marked “VHS” can be used with this video cassette player. 7 Avoid violent shocks to the VCP during packing and transport. LPT0457-001A 5 Wireless remote control 6 On screen display Connection A (basic) 8 Setting the video channel When using the remote control for operation of the video cassette player, make sure that it When “O.S.D” is set to “ON” ( See “9 Mode set”), various operational indicators appear on In order to use the video cassette player it must be connected between the antenna and the To watch videos on your TV, it must be set to the same UHF channel as the video cassette is pointed at the remote sensor window. the TV screen. TV. player. This channel is used as the video channel. You can also use the player’s remote control to operate a JVC television. This video cassette player has been preset to UHF channel 36. 8 1 Connect your TV antenna cable to the video cassette player’s ANT. IN terminal. 1 Operation mode indicators 1 Note: ! STANDBY/ON button q6 2 Tape speed SP/LP/EP Connect one end of the provided RF antenna cable to the video cassette player’s ] 2 • When you have connected the VIDEO/AUDIO OUT terminals of this video cassette player To turn the power on and off (standby SP 3 NTSC 3.58 3 Colour system indicator 2 RF. OUT terminal and the other end to the TV’s antenna terminal. to your TV’s video/audio in terminals (connection B of the “Connections” section), setting @ TRACKING –/+ buttons 4 TV Tape direction TV/VCR the video channel is not necessary. In this case simply set the TV’s TV/VCR switch to VCR. To adjust tracking during playback. 5 Counter display Connect the power cord to your household AC outlet. – TRACKING + # 4 0000 / button 6 7 0 +++ + Audio mode display (HR-P94K only) 3 AUTO IMPORTANT: 0000/X To reset the tape counter. HIFI –9 : 59 : 59 5 7 PLAY 6 Tape position indicator $ ¡ Z L R Before performing the following steps, make sure the player's power is off and there FF button 8 Cassette loaded mark REW FF To fast forward the video tape. Also to is no cassette inserted in the player. start forward shuttle search playback. Connection B MENU PAUSE % 8 PAUSE button POWER-ON STANDBY/REC STOP Access video channel set mode. To freeze the picture during playback. For connection of a TV that has VIDEO/AUDIO IN/OUT terminals. This connection is Also to engage the recording pause 1 Hold down § on the video cassette + TV PR– TV + necessary to record TV programmes. Use RCA type pin connection cords (available from – mode. player until the both of POWER-ON audio/video stores) for connection. This connection is in addition to connection A. REC OK/OSD ^ 2/3 buttons and STANDBY/REC indicators light. POWER ON STANDBY/REC To set the mode. Connections indicator indicator LP00000-000 VCP/TV 7 Follow steps 1 and 2 of “Connection A”. TV +/– (TV Volume) buttons 1 1 Transmitting window To adjust the TV volume. Make sure that the power to the video cassette player and TV is off before making the Set video channels. & OK/OSD button TEST SIGNAL 2 TV/VCR (Player) button following connections. Connect the TV’s VIDEO OUT and AUDIO OUT terminals to the video cassette 2 Set your TV to UHF channel 36. • To fix the setting. The channel on To switch JVC TV’s mode between TV 2 player’s VIDEO IN and AUDIO IN terminals. • If the two vertical white bars appear • To display the information on the and VIDEO. clearly on the screen as shown in the which the screen television's display. 3 TV button Connect the TV’s VIDEO IN and AUDIO IN terminals to the VCP’s VIDEO OUT and illustration on the right, press OK to the left appear * ¶ REC button To enable remote control of JVC TV.