DOCSLIB.ORG

Dual-Port Rs-422/485 Serial Interface Pc↔422/485 Serial Interface Converter

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Dual-Port Rs-422/485 Serial Interface Pc↔422/485 Serial Interface Converter © 2000. All rights reserved. Black Box Corporation. DUAL-PORT RS-422/485 SERIAL INTERFACE PC↔422/485 SERIAL INTERFACE CONVERTER These Converters let you double the RS-422 or RS-485 devices connected to your PC—or interface up to 31 or 62 IC600C IC030C-R2 RS-485 devices. IC173C IC170C Key Features ith the Dual-Port RS-422/485 to support up to 32 drivers and 32 The interface installs in just Supports RS-422/485 WSerial Interface card, you can receivers on one line. minutes. Turn off the PC’s power interface connections. add bar-code readers, scales, drill The interface is easy to and disconnect the power cord, presses, time clocks, and other configure. Simply set the address then remove the PC case and Directly address up to devices to your PC—and you and IRQ via DIP switches and on- screw holding the blank metal slot 64 RS-485 devices from don’t need additional line drivers board jumpers. cover. Remove the blank metal your PC. or converters. It even interfaces Troubleshooting’s a breeze, slot cover. Insert the board, to factory- automation equipment. too. A utility software package is replace the slot cover, screw, and No line driver or The IC600C Card uses the included with your Card for quick PC case. Replace the PC case converter needed. 16550 UART chip which features a diagnostics. and reconnect the power cord. Each port occupies 8 programmable baud rate, data Or, choose the PC↔422/485 You’re ready to go! format, and interrupt control, and Serial Interface Converter to link Connect your RS-422/485 consecutive I/O a 16-byte FIFO. The IC173C Card up to 31 devices. Two models are factory automation equipment to locations and has base uses the 16850 UART, and has a available: your PC with one of these cards. addressing that’s user- 128-byte FIFO buffer. • IC030C-R2 features a 16550 selectable. And you can set each serial UART and a 16-byte FIFO port as COM1 or COM2, so it’s buffer. Full- or half-duplex compatible with most • IC170C has a 16850 UART operation. communications software and and a 128-byte FIFO buffer. Easy to install. languages. Drivers and receivers for RS-422/485 are provided on the Utility software serial port. included for The RS-422 mode runs point- diagnostics. to-point and supports up to 10 receivers, and the RS-485 mode has the electrical characteristics 15798 1. Add bar code readers, scales, drill presses, time clocks, and other devices to your PC—without additional line drivers or converters. Technically Speaking ecause RS-422 and RS-485 are other types of interfaces. RS- can be active at any given • S2 sets the address for Bdifferential interfaces, they’re 422 signal levels range from 0 time). Port 2. to +5 volts. The standard does less susceptible to line noise, so About the UART Chip • Setting either switch “on” or not define a physical data integrity is never a problem. A UART (Universal Asynchronous “closed” corresponds to a “0” connector. • RS-422 is an Electronic Receiver/Transmitter) is an in the address, while leaving it Industries Association (EIA) • RS-485 is an EIA serial integrated circuit that converts “off” or “open” corresponds standard for a balanced interface standard for bytes from the computer bus into to a “1.” balanced, multipoint interface system with a high level of serial bits for transmission. Setting the Interrupts that incorporate tri-state noise immunity. It’s a Setting the interrupts on the card drivers providing high The 16550 UART features a 16- differential interface that is as simple as moving a jumper. defines voltage levels and tolerance to noise. Like RS- byte FIFO buffer for speeds of up • Move the jumper to the IRQ4 driver/receiver electrical 232, RS-485 is a differential to 115.2 kbps. The 16850 UART has setting for COM1. specifications. On this type of interface. It allows cable a 128-byte FIFO buffer for speeds interface, the difference in lengths up to 4000 feet (about of up to 460.8 kbps (sustained). • Move the jumper to the IRQ3 voltage between a pair of 1200 meters) and data rates up setting for COM2. Selecting the Address outputs or inputs defines logic to 10 Mbps. The signal levels Each serial port on the Interface levels. Contrast this to the RS- for RS-485 also range from 0 to occupies 8 consecutive I/I 232 interface, in which the +5 volts. This interface is ideal locations. DIP switches are used logic levels are defined as the for multi-drop or network to set the addresses for Ports 1 difference in voltage between environments, since it has a and 2. a single signal and a common tri-state driver (this allows the ground signal. Differential electrical presence of the • S1 sets the base address for interfaces are more immune to driver to be removed from the Port 1. noise or voltage spikes than line, so that only one driver Specifications Protocol: Asynchronous Temperature: Operating: 0 to 50° C (32 to 122° F); Storage: -20 to 70°C Speed: IC600C, IC030C-R2: Up to (-4 to 158° F) 115.2 Kbps; IC173C, IC170C: 460.8 kbps (sustained); (maximum rate Relative Humidity: 90% depends upon software, CPU, MTBF: > 150,000 hours and cable length) MTTR: < 0.25 hour Connectors: IC600C, IC173C: (2) DB9 male; IC030C-R2, IC170C: Manufacturing: IPC 610-A Class-III Ordering Information (1) DB25 male standards adhered to with a 0.1 ITEM CODE visual AQL and 100% functional Communications Chip: IC600C, testing; Boards are built to UL® Dual-Port RS-422/485 Serial Interface Card IC030C-R2: 16550 UART; IC173C, 94V0 rating and are 100% IC170C: 16850 UART 16550 UART.................................................................IC600C electrically tested. Boards are 16850 UART.................................................................IC173C Maximum Data Distance: Up to solder mask over bare copper or 1219.2 m (4000 feet) tin nickel. PC↔422/485 Serial Interface Converters Modem Control Signals: RS-422: Power: From the PC bus 16550 UART ..........................................................IC030C-R2 RTS and CTS Size: Half-card 16850 UART.................................................................IC170C System Requirements: ISA bus You may also need… Shipping Weight: 2 lb. (0.9 kg) Modular Thumbscrew Adapter Kits For IC600C: DB9 Female to RJ-45 Female (8-Wire) ..............FA756 For IC030C-R2: DB25 Female to RJ-45 Female (8-Wire)............FA771 15798 2..
Load more

Recommended publications
  • DAN189 EXAR UARTS in GPS APPLICATIONS March 2007 EXAR UARTS in GPS APPLICATIONS
    DAN189 EXAR UARTS IN GPS APPLICATIONS March 2007 EXAR UARTS IN GPS APPLICATIONS 1.0 INTRODUCTION This application note describes where an Exar UART can be used in a Global Positioning System (GPS) application. GPS has traditionally been used in military applications such as marine navigation, aircraft navigation, and weapon’s guidance. However, GPS applications have recently expanded to industrial and consumer applications such as vehicle navigation systems, fleet management, and personal navigation. In these applications, the Exar UART can be used in the GPS receiver and in the GPS application. FIGURE 1. GPS APPLICATION EXAMPLES GPS Applications Marine Navigation System Aircraft Navigation System Vehicle Navigation System Fleet Management System Personal Navigation System GPS Receiver TX RX UART RX TX UART 1.1 GPS Receiver A GPS receiver typically includes the following: • RF block for receiving the GPS data and converting it to digital data • Microprocessor for processing the data • ROM to store the firmware for processing the data • RAM used by the microprocessor for data processing • UART to send data to the GPS application The figure below shows a block diagram of a GPS receiver. FIGURE 2. GPS RECEIVER BLOCK DIAGRAM ROM RAM RF Block TX Microprocessor UART RX 1 DAN189 EXAR UARTS IN GPS APPLICATIONS The figure below shows a block diagram of an automobile GPS navigation system: FIGURE 3. AUTOMOBILE GPS NAVIGATION SYSTEM EXAMPLE Keypad ROM RAM Radio CD RX GPS UART Microprocessor DVD TX LCD The UART that has been used in the GPS receiver or in the GPS application has typically been an industry standard 16550 UART or a UART that is available on the microprocessor.
    [Show full text]
  • Ds430 Opb 16550 Uart
    0 OPB 16550 UART (v1.00d) DS430 December 2, 2005 0 0 Product Specification Introduction LogiCORE™ Facts This document provides the specification for the OPB Core Specifics 16550 UART (Universal Asynchronous QPro™-R Virtex™-II, QPro Receiver/Transmitter) Intellectual Property (IP). Virtex-II, Spartan™-II, Spartan-IIE, Supported Device Spartan-3, Spartan-3E, Virtex, The OPB 16550 UART described in this document has Family Virtex-II, Virtex-II Pro, Virtex-4, been designed incorporating features described in Virtex-E National Semiconductor PC16550D UART with FIFOs data Version of Core opb_uart16550 v1.00d sheet (June,1995),Discontinued (http://www.national.com/pf/PC/PC16550D.html). Resources Used The National Semiconductor PC16550D data sheet is Min Max referenced throughout this document and should be Slices 283 417 used as the authoritative specification. Differences LUTs 328 545 between the National Semiconductor implementation and the OPB 16550 UART Point Design implementation FFs 275 338 are highlighted and explained in Specification Block RAMs Exceptions. Provided with Core Features Documentation Product Specification • Hardware and software register compatible with all Design File Formats VHDL standard 16450 and 16550 UARTs Constraints File N/A • Implements all standard serial interface protocols Verification N/A - 5, 6, 7, or 8 bits per character Instantiation Template N/A - Odd, Even, or no parity detection and generation Reference Designs None - 1, 1.5, or 2 stop bit detection and generation Design Tool Requirements - Internal baud rate generator and separate receiver Xilinx Implementation ISE 6.1i or later clock input Tools - Modem control functions Verification ModelSim SE/EE 5.8e or later Simulation IPModelSim SE/EE 5.8e or later - False start bit detection and recovery - Prioritized transmit, receive, line status, and Synthesis XST modem control interrupts Support - Line break detection and generation Support provided by Xilinx, Inc.
    [Show full text]
  • Serial Communication Buses
    Computer Architecture 10 Serial Communication Buses Made wi th OpenOffi ce.org 1 Serial Communication SendingSending datadata oneone bitbit atat oneone time,time, sequentiallysequentially SerialSerial vsvs parallelparallel communicationcommunication cable cost (or PCB space), synchronization, distance ! speed ? ImprovedImproved serialserial communicationcommunication technologytechnology allowsallows forfor transfertransfer atat higherhigher speedsspeeds andand isis dominatingdominating thethe modernmodern digitaldigital technology:technology: RS232, RS-485, I2C, SPI, 1-Wire, USB, FireWire, Ethernet, Fibre Channel, MIDI, Serial Attached SCSI, Serial ATA, PCI Express, etc. Made wi th OpenOffi ce.org 2 RS232, EIA232 TheThe ElectronicElectronic IndustriesIndustries AllianceAlliance (EIA)(EIA) standardstandard RS-232-CRS-232-C (1969)(1969) definition of physical layer (electrical signal characteristics: voltage levels, signaling rate, timing, short-circuit behavior, cable length, etc.) 25 or (more often) 9-pin connector serial transmission (bit-by-bit) asynchronous operation (no clock signal) truly bi-directional transfer (full-duplex) only limited power can be supplied to another device numerous handshake lines (seldom used) many protocols use RS232 (e.g. Modbus) Made wi th OpenOffi ce.org 3 Voltage Levels RS-232RS-232 standardstandard convertconvert TTL/CMOS-levelTTL/CMOS-level signalssignals intointo bipolarbipolar voltagevoltage levelslevels toto improveimprove noisenoise immunityimmunity andand supportsupport longlong cablecable lengthslengths TTL/CMOS → RS232: 0V = logic zero → +3V…+12V (SPACE) +5V (+3.3V) = logic one → −3V…−12V (MARK) Some equipment ignores the negative level and accepts a zero voltage level as the "OFF" state The "dead area" between +3V and -3V may vary, many receivers are sensitive to differentials of 1V or less Made wi th OpenOffi ce.org 4 Data frame CompleteComplete one-byteone-byte frameframe consistsconsists of:of: start-bit (SPACE), data bits (7, 8), stop-bits (MARK) e.g.
    [Show full text]
  • SCR1 SDK. Altera Arria-V Starter Kit Edition. Quick Start Guide
    SCR1 SDK. Altera Arria-V Starter Kit Edition. Quick Start Guide © Syntacore, [email protected] Version 1.4, 2019-04-08 Table of Contents Revision History . 2 1. Setup equipment. 3 1.1. Prerequisites . 3 2. SDK HW assembly . 4 2.1. Connecting serial console . 4 2.2. Pins assignment. 4 3. Arria-V HW image update . 6 4. Booting the new FPGA image . 8 5. Resetting the board: . 9 6. UART connection settings . 9 7. Using UART terminal . 10 7.1. Load binary images to the Memory address . 10 7.2. Example: Dhrystone run from TCM memory . 12 7.3. Using OpenOCD. 13 7.3.1. Installing OpenOCD . 13 7.3.2. Starting the OpenOCD server. 13 7.3.3. Downloading and running an image using OpenOCD. 14 8. Building SDK FPGA-project for the Arria V GX SDK. 16 8.1. General structure of the SDK project. 16 8.2. Additional requirements for compilation . 16 8.3. Building SDK FPGA project. 17 8.3.1. FPGA firmware generation (sof-format) . 17 8.3.2. Converting FPGA-image to the board flash memory image (flash-format) . 17 8.3.3. SDK-specific pins assignment in FPGA-project . 19 8.4. SCR1 SDK FPGA-project functional description . 20 8.4.1. Common project structure . 20 8.4.2. Qsys SoC module structure. 20 8.4.3. Description of the blocks used in the SDK project . 21 8.4.3.1. SCR1-core. 21 8.4.3.2. AXI bridge . 21 8.4.3.3. Opencores UART 16550 IP . 21 8.4.4.
    [Show full text]
  • Low-Profile PCI Cards: a New Approach to Inner Space • Lavalanche Winners! • Distributor Profile Lava I/O News
    April 2002 Vol.4 No.4 Inside this issue: • Low-profile PCI cards: A New Approach to Inner Space • Lavalanche Winners! • Distributor profile Lava I/O News Low-Profile PCI Cards: A New Approach to Inner Space Most of us remember our first impression on looking inside the chassis of a desktop or tower computer: is that all there is? Apart from the motherboard, power supply, drives and cables, a few cards, and dust bunnies, things were pretty empty in there. And while we knew that air had to circulate inside the case, the empty spaces inside still seemed a bit large. Notebook computers came along and really confirmed the impression that the inside of typical computers had enough extra space for a game of baseball. sets standards for the PCI bus generally. As well as defining a maximum height for Low-profile PCI cards follow the “PCI Local cards designated as “low-profile”, the low-pro- The reason for all the empty space is historical: Bus Specification, Revision 2.2” or later, but file PCI specification also outlines two low-pro- the original PC's expansion cards were loaded in addition adopt the form factor require- file PCI card lengths —short (called “MD1”) with lots of separate and large components. ments of the new "PCI Engineering Change and long (“MD2”).An MD1 low-profile card has They were rather tall, and needed to be so. Notice —Low Profile PCI Card". Designed as a a maximum length of 4.72" (119.91 mm). An However, as integrated circuit technology collaborative effort by the PCI Special Interest MD2 card is longer than an MD1 card, but not advanced, expansion boards got smaller and Group and companies including IBM and longer than 6.6" (167.64 mm).
    [Show full text]
  • Z182 Com Port Appnote
    HIGH PERFORMANCE PC COMMUNICATION Zilog PORT USING THE Z182 MICROCONTROLLER HIGH PERFORMANCE PC COMMUNICATION PORT USING THE Z182 o meet the demands of high speed communications on the Information Superhighway, Zilog's Z182-based PC Communication Port "COMPORT.S™" software code provides the user with increased data buffering capabilities for faster communication between PCs T and modems. INTRODUCTION With the advent of the Information Superhighway, users will handle heavy traffic at only a sustained rate of 57.6 Kbps. be able to access information quickly and easily by means This factor, combined with limited CPU bandwidth (due to of PC/Modem communications. However, user-friendly complex operating systems), means users cannot take full operating systems, capable of processing large amounts advantage of the high throughput that today’s modems of data, become so performance intensive that data com- can accommodate. munication becomes a bottleneck. Although there have been many advances in modem and PC design, a satis- PC Week's labs (July 1992) analyzed the serial card factory solution to the PC/modem communication bottle- bottleneck issue and their tests showed that a standard neck has not been found. serial card could not reliably sustain data transfer over 19.2 Kbps. However, when using a 16550 UART loaded The PC/Modem communication bottleneck is caused by serial card, the user could expect 57.6 Kbps of reliable, the PC standard serial cards used to connect to the sustained data transfer. This is great for V.32bis, but what modems. Conventional serial cards were designed to about V.FAST and beyond? Serial Port Limitations If you look at a PC Standard Serial Card, you will find a 8250 quickly to interrupts in a multi-tasking system? The answer or 16450 UART as well as RS-232 line drivers.
    [Show full text]
  • XR20M1170 Data Sheet
    XR20M1170 I2C/SPI UART WITH 64-BYTE FIFO JUNE 2019 REV. 1.1.2 GENERAL DESCRIPTION FEATURES 1.62 to 3.6 Volt operation The XR20M11701 is a high performance universal asynchronous receiver and transmitter (UART) with Selectable I2C/SPI interface 64 byte TX and RX FIFOs and a selectable I2C/SPI SPI clock frequency up to slave interface. The XR20M1170 operates from 1.62 to 3.63 volts. The enhanced features in the 18MHz at 3.3V XR20M1170 include a programmable fractional baud 16MHz at 2.5V rate generator, an 8X and 4X sampling rate that 8MHz at 1.8V allows for a maximum baud rate of 16Mbps at 3.3V. The standard features include 16 selectable TX and Full-featured UART RX FIFO trigger levels, automatic hardware (RTS/ Data rate of up to 16Mbps at 3.3V CTS) and software (Xon/Xoff) flow control, and a Data rate of up to 12.5Mbps at 2.5V complete modem interface. Onboard registers provide the user with operational status and data Data rate of up to 8Mbps at 1.8V error flags. An internal loopback capability allows Fractional baud rate generator system diagnostics. The XR20M1170 is available in Transmit and receive FIFOs of 64 bytes the 24-pin QFN, 16-pin QFN, 24-pin TSSOP and 16- 16 selectable TX and RX FIFO trigger levels pin TSSOP packages. Automatic hardware (RTS/CTS) flow control NOTE: 1 Covered by U.S. Patent #5,649,122 Automatic software (Xon/Xoff) flow control APPLICATIONS Halt and resume transmission control Portable appliances Automatic RS-485 half-duplex direction control output via RTS# Battery-operated devices Wireless Infrared (IrDA 1.0 and 1.1) encoder/ Cellular data devices decoder Factory automation and process controls Automatic sleep mode (< 15uA at 3.3V) General purpose I/Os Full modem interface Crystal oscillator (up to 24MHz) or external clock (up to 64MHz) input 24-QFN, 16-QFN, 24-TSSOP, 16-TSSOP packages FIGURE 1.
    [Show full text]
  • Microprocessors and Microcontrollers (EE-231) Main Objectives
    Microprocessors and Microcontrollers (EE-231) Main Objectives • 16550 Communication Device • ADC and DAC interfacing 16550 Programmable Communications Interface • National Semiconductor Corp’s PC16550D is a programmable communications interface designed to connect to virtually any type of serial interface. • 16550 is a universal asynchronous receiver/transmitter (UART) fully compatible with Intel microprocessors. • 16550 operates at 0–1.5 M baud. – baud rate is bps (bits transferred per second) including start, stop, data, and parity • 16550 also includes a programmable baud rate generator and separate FIFOs for input and output data to ease the load on the microprocessor. • Each FIFO contains 16 bytes of storage. • The most common communications interface found in the PC and many modems. Asynchronous Serial Data • Asynchronous serial data are transmitted and received without a clock and in frames as shown in figure. – each frame contains a start bit, seven data bits, parity, and one stop bit • Most Internet services use 10 bits, but normally do not use parity. • instead, eight data bits are transferred, replacing parity with a data bit 16550 Functional Description • The device is available as a 40-pin DIP (dual in-line package) or as a 44-pin PLCC (plastic leadless chip carrier). • Two completely separate sections are responsible for data communications. – the receiver and the transmitter • Because each sections is independent, 16550 is able to function in simplex, half-duplex, or full-duplex modes. The pin-out of the 16550 UART. 16550 Functional Description • A major feature of the 16550 is its internal receiver and transmitter FIFO (first-in, first-out) memories. • Because each is 16 bytes deep, the UART requires attention from the processor only after receiving 16 bytes of data.
    [Show full text]
  • Operating System Support Matrix
    Operating System Win Win Win Win Win Win Win Win THEOS Product Description Win Win Win Win Windows Win XP Win XP Server Server Server Server Server Server Win 7 Win 7 Win 8 Win 8 Server Server Win 8.1 Win 8.1 Corona DOS Win 3.x Win NT4 Win 95 Win 98 Win 98SE Win Me Win 2000 Server Server Vista Vista Thin a Mac 8.6+ QNX 6.2 THEOS SCO 5.07 SCO 6.0 32 64 2003 2003 R2 2003 R2 2008 2008 2008 R2 32 64 32 64 2012 2012 R2 32 64 Linux Ver. 5.0 2000 2003 64 32 64 Client 32 32 64 32 64 64 64 64 PL182 USB-Serial Links USB-Serial Link 2-232-DB9 Two RS-232, 9-pin DB-9s USB-Serial Link 4-232-DB9 Four RS-232, 9-pin DB-9s USB-Serial Link 4-232-DB9 Cabled Four RS-232, 9-pin DB-9s with fan-out cable Serial PCIe SSerial-PCIe One 25-pin port, 16550 UART SSerial-PCIe/LP One 25-pin port, 16550 UART, low-profile DSerial-PCIe Two 9-pin ports, 16550 UARTs DSerial-PCIe/LP Two 9-pin ports, 16550 UARTs, low-profile Quattro-PCIe Four 9-pin ports, 16550 UARTs Serial PCI SSerial-PCI One 9-pin port, 16550 UART ? SSerial-PCI/LP One 25-pin port, 16550 UART, low-profile ? RS422 SS-PCI One 9-pin port, 16550 UART, RS-422 pinout ? LavaPort-650 One 9-pin port, 16650 UART ? DSerial-PCI Two 9-pin ports, 16550 UARTs
    [Show full text]
  • Add Ports to Your PC with These PCI Cards Featuring High-Speed Buffered Uarts
    FREE 24-hour Tech Support: 724-746-5500 blackbox.com © 2010. All rights reserved. Black Box Corporation. PCI Cards Add ports to your PC with these PCI cards featuring high-speed buffered UARTs. 4/12/2010 #26217 ­­1 of 6 Connect up to 31 RS-485 devices to each port on the Quad-Port RS-232/422/485 PCI Card. FEaturES » Provide an easily configurable interface that’s simple to connect. » Some models meet a variety of interface Quad-Port RS-232/422/485 standards. PCI Card » Advanced buffered UARTs for faster (IC974C) data transmission. » Low-profile models fit in the PCI slots of newer, slimmer PCs. » Opto-isolation available on some models. » Drivers for all Windows operating systems are included. Time Clocks OVERVIEW When you need to add extra PCI ports to your personal com puter, In both RS-232 and RS-422 modes, the PCI cards work seamlessly select a PCI card from Black Box®. All our cards feature speedy with your standard operating system’s serial driver. In RS-485 mode, buffered Universal Asynchronous Receiver/Trans mitters (UARTs); the cards’ special autoenable feature allows the RS-485 ports to be these are integrated circuits that convert bytes from the computer viewed by the operating system as a COM port. This enables you to bus into serial bits for transmission. use a standard COM driver (instead of a custom software driver) for The cards are designed to maxi mize DOS, Linux®, OS/2®, QNX, your high-speed Windows® 95/98/Me/XP, Windows 2000, Windows NT®, and UNIX® RS-485 connections.
    [Show full text]
  • 8-Port PCI Express Serial Card with 16550 UART
    8-Port PCI Express Serial Card with 16550 UART Product ID: PEX8S1050LP Add eight RS-232 DB9 serial ports to your desktop computer, through two PCIe expansion card slots. This PCI express serial card, with two breakout cables, provides you with multiple ports to connect a wide variety of serial peripherals, at speeds of up to 921.4Kbps. Connect your Peripherals with 8 Serial Ports The PCI express serial port card makes it easy to add serial ports to connect your peripherals including printers, scanners, credit/debit card readers, PIN pads and modems, industrial controls and more. The 8 port PCIe serial card includes 2 breakout cables - each with 4 DB9 connectors. Versatile Use The low profile PCIe serial card is the ideal choice for adding serial ports, even when space is at a premium. The DB9 serial card is designed to fit into small form factor and standard computer cases. The card comes pre-configured with a low-profile bracket, and includes two optional full-profile brackets, so installation is easy regardless of the case form factor. www.startech.com 1 800 265 1844 Maximum Compatibility With broad OS support, including for Windows and Linux, this PCI Express card is easy to integrate into mixed environments. PEX8S1050LP is backed by a StarTech.com lifetime warranty and free lifetime technical support. www.startech.com 1 800 265 1844 Certifications, Reports Applications and Compatibility • Manufacturing (CNC machinery, process control equipment, bar code scanners, serial printers) • POS (credit/debit card readers, receipt printers,
    [Show full text]
  • RS232/422/485 Serial Communications
    RS232/422/485 Serial Communications Users Manual (SERIAL) Version 5.1 August 19, 2011 This software is provided as-is. There are no warranties, expressed or implied. Copyright (C) 2011 All rights reserved MarshallSoft Computing, Inc. Post Office Box 4543 Huntsville AL 35815 USA Email: [email protected] Web: www.marshallsoft.com MARSHALLSOFT is a registered trademark of MarshallSoft Computing. 1 TABLE OF CONTENTS 1 The UART Page 3 1.1 Emulated UARTs Page 3 1.2 UART Types Page 3 1.2.1 National 8250 Page 3 1.2.2 National 16450 Page 3 1.2.3 National 16550 Page 3 1.2.4 StarTech 16650 Page 3 1.2.5 Texas Instruments 16750 Page 3 1.3 UART Operation Page 4 1.4 RS-232 Signals Page 5 1.5 UART Registers Page 6 1.6 Register Summary Page 7 2 Modems Page 10 2.1 Modem Standards Page 10 2.1.1 Speed Page 10 2.1.2 Data Compression Page 10 2.1.3 Error Control Page 10 2.2 Modem AT Command Set Page 11 2.3 Flow Control Page 11 2.4 Modem Initialization Page 12 2.5 Modem CONNECT Page 12 2.6 More Modem Documentation Page 12 3 RS422 and RS485 Page 13 4 Other Serial Devices Page 13 2 1 The UART The heart of serial communications is the "Universal Asynchronous Receiver Transmitter” or UART for short. The UART is responsible for controlling the computer's RS-232/422/485 port. 1.1 Emulated UARTs Some computers, particularly laptops and Handheld / Pocket PC’s, do not contain real UART chips.
    [Show full text]