Dust Cat1-22

Total Page:16

File Type:pdf, Size:1020Kb

Dust Cat1-22 Dust Collector Fittings And Woodworking Accessories All Sheet Metal Made in USA KenCraft Co Inc 821 N Westwood Ave Toledo OH 43607 Phone 419-536-0333 Fax 419-536-0944 www.kencraftcompany.com CAST ALUMINUM BLAST GATES SIZE ITEM NO PRICE SIZE ITEM NO PRICE 2” BG2 11.00 10” BG10 42.50 3” BG3 11.80 12” BG12 53.30 4” BG4 11.45 14” BG14 * 5” BG5 16.20 16” BG16* * 6” BG6 16.60 18” BG18* * 7” BG7 24.80 20” BG20* * 8” BG8 26.70 22” BG22* * 9” * BG9* 42.95 24” BG24* * * SPECIAL ORDER, CALL FOR AVAILABILITY— ALLOW FOR FREIGHT SHEET METAL BLAST GATE ADAPTERS 24 GAUGE SIZE ITEM NO. PRICE 4” BGA4 5.30 Sample blast gate with 5” BGA5 5.70 blast gate adapter 6” BGA6 6.05 BLAST GATES AND BLAST GATE ADAPTERS SOLD SEPERATELY SHEET METAL TAPER REDUCERS 26 GAUGE SIZE ITEM NO. PRICE 10x9 R109 13.40 10x8 R108 13.40 8x6 R86 10.05 8x7 R87 10.05 8x5 R85 9.99 7x6 R76 9.75 7x5 R75 9.75 6x5 R65 7.80 6x4 R64 7.80 6x3 R63 7.80 5x4 R54 7.80 5x3 R53 7.80 UNIVERSAL REDUCER 4x3 R43 7.80 JUST CUT TO SIZE 4x2 1/2 R425 14.95 4x2 R42 14.95 6” TO 1” PVC UR 5.95 METAL DUCT AND METAL FITTINGS SHOULD BE PROPERLY GROUNDED TO PREVENT STATIC ELECTRIC BUILD UP SHEET METAL WYE BRANCHES 24 GAUGE SIZE ITEM PRICE SIZE ITEM PRICE NO. NO. 10X10X10 Y101010 55.35 6x6x5 Y665 27.95 10X10X8 Y10108 55.35 6x6x4 Y664 29.15 10X10X6 Y10106 55.35 6x5x5 Y655 36.75 8x8x8 Y888 38.30 5x5x5 Y555 26.85 8x8x6 Y886 38.30 5x5x4 Y554 24.50 8x8x4 Y884 38.30 5x4x4 Y544 36.90 7X7X7 Y777 32.85 4x4x4 Y444 22.85 Custom Sizes Available. Please 6x6x6 Y666 29.25 allow 2 weeks lead time. Sheet metal reducers are available in a wide range of sizes. This allows a wye branch to be converted to the combination that is needed for your system. TRUE “Y” BRANCHES 26 GAUGE Available in 3 styles: - Crimped on two branches or TYxxx - Crimped on single side TYxxxB - No Crimp SIZE ITEM NO PRICE 4X4X4 TY444 / TY444B 24.50 5X4X4 TY544 / TY544B 24.50 5X5X5 TY555 / TY555B 24.50 True wye branches have the following crimp option. Please indicate which crimp you need 6X4X4 TY644 / TY644B 21.00 when ordering: - Crimped on two branches - Crimped on single side (B) 6x6x6 TY666 / TY666B 21.00 - Or specify NO CRIMP 8x8x8 TY888 / TY888B 24.50 SHEET METAL SADDLES SIZE ITEM NO PRICE 4” on 4” SAD44 26.60 4” on 6” SAD46 26.60 4” on 8” SAD48 26.60 6” on 6” SAD66 27.40 METAL DUCT AND METAL FITTINGS SHOULD BE PROPERLY GROUNDED TO PREVENT STATIC ELECTRIC BUILD UP SNAP LOCK PIPE 26 GAUGE SIZE ITEM NO PRICE SIZE ITEM PRICE 4x24 P424 5.75 4x60 P460 11.45 5x24 P524 6.90 5x60 P560 13.95 6x24 P624 7.90 6x60 P660 15.40 7x24 P724 8.50 7x60 P760 18.60 8x24 P824 9.80 8x60 P860 19.70 PIPE CAPS — 26 GAUGE CRIMPED UNCRIMPED SIZESIZESIZE ITEM NO PRICE SIZESIZESIZE ITEM NO PRICE 6” C6 6.25 6” CU6 6.25 5” C5 6.25 5” CU5 6.25 4” C4 6.25 4” CU4 6.25 24 gauge Galvanized No. 8 x 1/2 Zip Screws Hanger Strap Foil Tape 100 pc 50’ Roll 2.5” x 180’ Roll DUST COLLECTOR ACCESSORIES ITEM DESCRIPTION ITEM NO. PRICE 8 X 1/2” Zip Screws ZS812 3.99 Galvanized Strap GS50 13.60 Foil Tape FOTA 15.99 METAL DUCT AND METAL FITTINGS SHOULD BE PROPERLY GROUNDED TO PREVENT STATIC ELECTRIC BUILD UP HOSES ARE AVAILABLE IN STOCK IN 10 FOOT AND 5 FOOT SECTIONS!! PLASTIC REINFORCED CORRUGATED HOSE 15 mil SIZE ITEM NO. PRICE 2” X 10’ CH2 17.70 2” x 5’ CH2 - 1/2 10.45 2 1/2” X 10’ CH25 17.25 2 1/2” X 5’ CH25 - 1/2 10.15 Photo above is for plastic hose 3” X 10’ CH3 17.35 sized 2” through 4” diameters 3” X 5’ CH3 - 1/2 10.25 4” X 10’ CH4 23.90 4” X 5’ CH 4 - 1/2 14.10 5” X 10’ CH5 36.15 5” X 5’ CH5 - 1/2 21.30 WIRE REINFORCED CORRUGATED HOSE 24 mil SIZE ITEM PRICE Photo of 5” plastic hose 3” x 10’ WCH3 39.60 3” x 5’ WCH3 - 1/2 23.35 4” X 10’ WCH4 45.20 4” X 5’ WCH4 - 1/2 26.70 WIRE HOSE 5” X 10’ WCH5 50.70 5” X 5’ WCH5 - 1/2 29.85 6” X 10’ WCH6 55.00 6” X 5’ WCH6 - 1/2 32.35 8” x 10’ WCH8 73.99 Most hoses are available in lengths up 8” x 5’ WCH8 - 1/2 43.55 to 50’. These are special order. One and a half week lead time needed. Call or email for pricing. HOSE CONNECTORS 26 GAUGE SIZE ITEM NO PRICE 6” SHEET METAL HC6 3.90 5” SHEET METAL HC5 3.50 PVC Sheet Metal 4” SHEET METAL HC4M 3.10 4” PLASTIC/PVC HC4 2.80 3” PLASTIC/PVC HC3 1.35 METAL DUCT AND METAL FITTINGS SHOULD BE PROPERLY GROUNDED TO PREVENT STATIC ELECTRIC BUILD UP SHEET METAL ADJUSTABLE 45 DEGREE ELBOWS 26 GAUGE SIZE ITEM NO. PRICE 4” AE445 5.40 5” AE545 6.05 6” AE645 6.75 7” AE745 7.55 8” AE845 7.55 ADJUSTABLE SHEET METAL 90 DEGREE ELBOWS 26 GAUGE SIZE ITEM NO. PRICE 4” AE4 4.80 5” AE5 4.95 6” AE6 5.25 7” AE7 6.40 8” AE8 6.50 LONG SWEEP ELBOWS 20 GA 90 DEGREE 45 DEGREE SIZE ITEM NO PRICE ITEM NO PRICE 4” E490 25.75 E445 15.35 5” E590 31.45 E545 19.50 6” E690 36.35 E645 25.60 7” E790 45.60 E745 29.45 8” E890 53.85 E845 30.70 METAL DUCT AND METAL FITTINGS SHOULD BE PROPERLY GROUNDED TO PREVENT STATIC ELECTRIC BUILD UP WIRE HOSE CLAMPS SIZE ITEM NO PRICE SIZE ITEM NO PRICE 6” WHC6 .95 3” WHC3 .60 5” WHC5 .80 2 1/2” WHC25 .55 4” WHC4 .80 2” WHC2 .55 FLOOR SWEEP 24 Gauge SIZE ITEM NO PRICE 4” FLOOR 49.40 A floor sweep in the shop allows for quick, easy clean up of dust and chips that collect on the floor. Attach the floor sweep to a hose and a blast gate. When ready to sweep, simply open the gate and sweep your dust into the opening of the floor sweep. The debris is then taken into your dust collection system. Fast & easy clean up! ECONOMY FLOOR SWEEP 24 Gauge SIZE ITEM NO PRICE 4” ECONFLOOR 29.80 AIRTIGHT TAKE OFF 25 Gauge Used to convert a Flat/plain box into straight pipe and hose. SIZE ITEM NO PRICE Useful on the back or radial arm saw 6” STO6 8.35 boxes, table saw boxes etc. METAL DUCT AND METAL FITTINGS SHOULD BE PROPERLY GROUNDED TO PREVENT STATIC ELECTRIC BUILD UP Trash Can Dust Separator Universal Dust Port Fits 33 Gallon Trash Can Fits over a 3” Opening 20” Diameter Can Item # DP Item # LDCS Joiner Dust Hood Fits 6.5” x 6.5” Chute Universal Dust Hood Item # JDH Fits 4.5” opening Uses include: bandsaws, table saws, shapers, sanders Item #DH Table Saw Dust Hood Fits most 8”, 10” & 12” contractor type table saws Item # TSDH MACHINE ACCESSORIES ITEM DESCRIPTION OVERALL PIECE SIZE ITEM NO PRICE Trash Can Separator Fits 20” diameter can LDCS 30.90 Opening = 2.5” OD; Universal Dust Port DP 5.95 4” x 3.625” x 3.813” Opening = 4” OD; Joiner Dust Hood JDH 5.95 2.5” x 8.25” x 8.25” Universal Dust Hood 2.5” x 6.25” x 6.25” DH 5.95 Opening = 4” OD; Table Saw Dust Hood TSDH 6.95 2.5” x 12.25” x 12.25” METAL DUCT AND METAL FITTINGS SHOULD BE PROPERLY GROUNDED TO PREVENT STATIC ELECTRIC BUILD UP Be sure to visit our store or website for your woodworking needs: • Domestic & Exotic Hardwood lumber • Hardwood Moldings • Thin Stock Lumber • Turning Lumber • Ash Bat Blanks • Baltic Birch Plywood • Red Oak Plywood • Prefinished Maple Plywood • Phenolic Coated Plywood • Special Order Cherry, Walnut & Maple Plywood • Router Master Router Pad • Hardwood Dowels • Hot Melt Edgebanding • Whiteside Router Bits • The Kreg Jig • Veneers .
Recommended publications
  • Owner's Manual & Safety Instructions
    Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. 20i Visit our website at: http://www.harborfreight.com email our technical support at: [email protected] Visit our website at: http://www.harborfreight.com email our technical support at: [email protected] When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible. Copyright© 2020 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in Read this material before using this product. any shape or form without the express written consent of Harbor Freight Tools. Failure to do so can result in serious injury. Diagrams within this manual may not be drawn proportionally. Due to continuing SAVE THIS MANUAL. improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. table of contents Safety ......................................................... 2 Maintenance ............................................... 6 Specifications ............................................. 4 Parts List and Diagram ............................... 7 Setup .......................................................... 4 Warranty ..................................................... 8 Sa Operation .................................................... 4 F ety WarninG SyMBOLS anD DeFinitiOnS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
    [Show full text]
  • 2-1/2" Complete Dust Collection Network Assembled According to the Instructions
    INSTRUCTION SHEET Model No. 70259 WARNING Do not attempt to operate tool until it is completely 2-1/2" Complete Dust Collection Network assembled according to the instructions. WARNING QUESTION... Metal shavings or dust can set sawdust on fire. Collect wood materials only. Do not collect metal shavings or 1•847•780•6120 dust with anything that has metal in it. Disconnect dust collector system from any tool before working on metals. Visit us on the web at www.powertecproducts.com Remove all traces of wood dust from inside that tool’s dust traps. Remove all traces of metal shavings or dust before reconnecting the vacuum/dust collector. Put these instructions and the original sales invoice in a safe, dry place for future reference. CAUTION If using this Dust Collection Network to help keep airborne wood dust in heavy usage within acceptable limits, you IMPORTANT SAFETY INSTRUCTIONS must regularly monitor airborne dust and maintain the Dust This system is designed to be used with a vacuum cleaner/ Collection Network to avoid exceeding dust limits. Each dust extractor with at least 100 CFM. Always follow basic application is unique. The maintenance schedule must be safety precautions including the following. for the specific Dust Collection Network being used. IMPORTANT: Always ensure the dust collection network is WARNING properly grounded. If in doubt, contact an electrician. For your own safety, read and understand all warnings and SAVE ALL WARNINGS AND INSTRUCTIONS operating instructions before using any tool or equipment. FOR FUTURE REFERENCE WARNING UNPACKING Some dust created by operation of power tool contains chemicals known to the State of California to cause cancer, Refer to Figure 1 birth defects or other reproductive harm.
    [Show full text]
  • Easy Duct Technical Manual
    EASY DUCT™ TECHNICAL MANUAL THE EASY DUCT ADVANTAGE • Simple to install - No special tools or training required • Clamp-together components can be taken apart and reused • Flexible - Easily connects to existing ductwork • Components and adapters fit every system • Adjustable duct fittings simplify connections • Smooth interior surface helps prevent clogs EASY DUCT™ - TECHNICAL MANUAL EASY DUCT™ - TECHNICAL MANUAL TABLE OF CONTENTS DESCRIPTION PAGE Adjustable Nipple Assembly For Dry Application 34 Adjustable O-Ring Material 4 Air Volume Chart 37 Blast Gate (Auto) 17 Blast Gates (Manual & Energy Saving) 18-19 Bleed-In Valve 15 Branch Styles 31 Ceiling Hanging Method 23 Clamp Diagram 3 Clamp Gasketing Alternatives 4 Construction Methods 5 Diverter Valve 20 Dry System Installation 30 Elbows & Fittings 6 Engineering Specifications 1 Flanged Duct Specifications 2 Flashing (Wall & Roof) 21 Gauge Limitations 8 Gauge Upgrades For Elbows 7 Gripple Hanger System 24 High Temp Fume Or Exhaust Applications 28 In-Line Sound Silencer 26 Installing An In-Cut Or Tap-In 16 Labor Guidlines & What To Be Aware Of When Ordering 27 Leakage 10 No-Loss Stack-Head 26 Oil Mist Or Wet Application For Pipe 35 Oil Mist Or Wet Application For Installation Of Adjustable Nipple 36 Pipe Stand With Bracket Hanger 23 Reducer Styles 32 Rigid & Ultra Flex Hose 14 Rubber Flex Hose 13 Sizing A System & Cfm/Fpm Chart 11 Sizing Branches 33 Sizing Elbows & Special Components 12 Structural Integrity & Collapsibility 9 Wall Mounting 22 Wet System Installation 29 i Donaldson Torit donaldsontorit.com | 800-365-1331 1 EASY DUCT™ - TECHNICAL MANUAL EASY DUCT™ - TECHNICAL MANUAL ENGINEERING SPECIFICATIONS DUCT-WORK: All duct-work shall be of a clamp-together design using a die-formed, rolled edge in which is then joined together by a single lever clamp of similar material.
    [Show full text]
  • Woodworking Glossary, a Comprehensive List of Woodworking Terms and Their Definitions That Will Help You Understand More About Woodworking
    Welcome to the Woodworking Glossary, a comprehensive list of woodworking terms and their definitions that will help you understand more about woodworking. Each word has a complete definition, and several have links to other pages that further explain the term. Enjoy. Woodworking Glossary A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z | #'s | A | A-Frame This is a common and strong building and construction shape where you place two side pieces in the orientation of the legs of a letter "A" shape, and then cross brace the middle. This is useful on project ends, and bases where strength is needed. Abrasive Abrasive is a term use to describe sandpaper typically. This is a material that grinds or abrades material, most commonly wood, to change the surface texture. Using Abrasive papers means using sandpaper in most cases, and you can use it on wood, or on a finish in between coats or for leveling. Absolute Humidity The absolute humidity of the air is a measurement of the amount of water that is in the air. This is without regard to the temperature, and is a measure of how much water vapor is being held in the surrounding air. Acetone Acetone is a solvent that you can use to clean parts, or remove grease. Acetone is useful for removing and cutting grease on a wooden bench top that has become contaminated with oil. Across the Grain When looking at the grain of a piece of wood, if you were to scratch the piece perpendicular to the direction of the grain, this would be an across the grain scratch.
    [Show full text]
  • Wood Dust Collection System Design and Inspection
    WorkSafe Bulletin Wood dust collection system design and inspection The hazards of wood dust Wood dust emitted from sawing, planing, sanding, and other operations can cause a variety of health effects when inhaled. Depending on the type of wood used, the effects can range from allergies to nasal cancer. Wood dust is also flammable and combustible. Fine dust accumulations may explode if an ignition source (e.g., open flame, friction, or sparks) is present. A dust collection system can reduce the risks A properly designed wood dust collection system will reduce worker exposure and help prevent accumulations of dust around operating equipment. A typical system Dust collection system for a table saw consists of a capture hood, a fan, ducting, and a filter. Dust collection systems can be purchased or designed and constructed for a particular operation or piece of equipment. Equipment suppliers can provide some guidance. However, a professional mechanical engineer (P.Eng.) who specializes in dust control systems can ensure that a system is properly designed for a particular operation to maximize efficiency and safety. Ensuring a collection system works well The following recommendations can help ensure that a wood dust collection system works efficiently: • Place the collection hood as close as possible to the point of dust generation. • Ensure that the hood encloses the dust-producing operation as much as possible and does not interfere with the process. • Position the collection hood to take advantage of any Avoid sharp bends or connections in ducting inertia the dust might have (e.g., on the bottom of a saw blade designed to cut on the downstroke).
    [Show full text]
  • INDUSTRIAL STRENGTH Ductwork Direct Dust & Fume Collection Industrial Ventilation in Stock Ready to Ship Direct from the Manufacturer Product Catalog
    INDUSTRIAL STRENGTH Ductwork Direct Dust & Fume Collection Industrial Ventilation In Stock Ready to Ship Direct from the Manufacturer Product Catalog www.airhand.com Helpful Information Dust Collection Systems Dust collection systems can be complicated, here are a few simply steps to an effective and efficient dust collection system. We have simplified the dust collection system for smaller shops, it is important to know federal, state Definitions and localities have codes and regulations enforced by AHJ • CFM -Air Volume in Cubic Feet per Minute. (Authorities Having Jurisdiction) governing sales, construc- • FPM - Velocity of Air in Feet per Minute. tion, installation and or use of dust collection systems. • SP - Static Pressure. This is expressed There are five simple steps to an effective and efficient dust in inches water gauge. It is resistance to collection system: air at rest in a duct, and is also commonly called “resistance,” friction,” “friction loss” or 1. Draw a floor plan of your shop “pressure loss”. 2. Determine Duct Velocity (FPM) • VP - Velocity Pressure: expressed in inches water gauge. It is kinetic pressure in the 3. Determine Diameter and CFM of each Branch direction of flow necessary to cause air at 4. Determine Diameter and CFM of Main Duct rest to flow at a given velocity. 5. Figure System Resistance (SP - Static Pressure) Typical dust collection system 6" 8" 8" 5" 4" 4" 4" 5" Table Saw Lathe Radial Floorsweep Sander Dust Collector We ALWAYS recommend you do these calculations BEFORE you purchase your dust collector or ductwork. To properly size your dust collector, you NEED to know your CFM requirements and at what Static Pressure your system will be operating.
    [Show full text]
  • Extracurricular Project Enhances Student Learning: a Case Study
    AC 2010-145: EXTRACURRICULAR PROJECT ENHANCES STUDENT LEARNING: A CASE STUDY Nicholas Harlow, Western Kentucky University Nicholas Harlow is an undergraduate student in Mechanical Engineering and is currently in his senior year. He is also employed as a student worker for WKU’s Thermal-Fluid Mechanics Laboratory. Robert Choate, Western Kentucky University Robert Choate is an Associate Professor of Mechanical Engineering at Western Kentucky University. He teaches thermo-fluid and professional component courses, including Sophomore Design, Thermo-Fluid Systems Lab and ME Senior Project Design course sequence. Prior to teaching at WKU, he was a principal engineer for CMAC Design Corporation, designing telecommunication, data communication and information technology equipment. H. Joel Lenoir, Western Kentucky University Joel Lenoir is the Layne Professor of Mechanical Engineering at WKU, and primarily teaches in the dynamic systems and instrumentation areas of the curriculum. His industrial experience includes positions at Michelin Research and Oak Ridge National Laboratory, as well as extensive professional practice in regional design and manufacturing firms. Page 15.570.1 Page © American Society for Engineering Education, 2010 Extracurricular Project Enhances Student Learning: A Case Study Abstract Recently at Western Kentucky University’s mechanical engineering thermal-fluids laboratory, a student worker, the author of this paper, was given the opportunity to design, build, and test (DBT) a dust collector performance test bed. The development of this test bed was inspired by an article in Wood Magazine, which described a method for testing the performance of various portable dust collectors. The test bed developed is being used for instructional purposes in one laboratory course in the Mechanical Engineering (ME) Program.
    [Show full text]
  • MODEL G0548ZP G1028Z2/G1029Z2/G1029Z2P DUST COLLECTOR OWNER's MANUAL (For Models Manufactured Since 8/18)
    MODEL G0548ZP G1028Z2/G1029Z2/G1029Z2P DUST COLLECTOR OWNER'S MANUAL (For models manufactured since 8/18) 247570 G0548ZP G1028Z2/G1029Z2 COPYRIGHT © FEBRUARY, 2012 BY GRIZZLY INDUSTRIAL, INC. REVISED AUGUST, 2018 (MN) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL14676 PRINTED IN TAIWAN V2.08.18 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to proper installation in a safe environment, personnel training and usage authorization, proper inspection and maintenance, manual availability and compre- hension, application of safety devices, cutting/sanding/grinding tool integrity, and the usage of personal protective equipment. The manufacturer will not be held liable for injury or property damage from negligence, improper training, machine modifications or misuse. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement and other masonry products. • Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work.
    [Show full text]
  • Bright Ideas in a Basement Shop  Michael L
    AMERICA’S TOP SHOPS Bright Ideas in a Basement Shop michael l. maine There’s nothing dark and dreary about the workshop Mark Koritz built in the basement of his surburban St. Louis, Missouri, home. WORKING IN A LONG AND NARROW SHOP (above), Mark Koritz took advantage of the obvious storage possibilities—including the floor joists overhead—to keep his shop neat and orderly. Mark’s 30-year-old workbench (left) occupies a prime spot in the center of the shop. o say sunglasses are a benches with white drawers provide Sawdust on the floor is a rarity, requirement for spending time plenty of storage and reinforce the though, because of the four-bag, 3-hp Tin Mark Koritz’s workshop clean, tidy look Mark wanted. For remote-controlled dust-collection would be a stretch, but a bright space a touch of color and comfort, red, system. Six-inch PVC pipe attached to was a priority when Mark designed his yellow, blue, and green rubber mats are the floor joists runs the entire length 15×55' shop. placed at key workstations. of the shop. Branch lines between the “Lighting is a key factor in a shop. I “I’m a sort of a neat freak when joists lead to various workstations. had all the walls and the ceiling painted it comes to having a nice shop and Joints are sealed with rope caulk. The white to reflect light and make the home,” says Mark. “That is not to say system culminates in a small room at ceiling seem higher,” Mark explains.
    [Show full text]
  • How to Design a Dust Collection System
    THE WORLD’S FASTEST DUCTING How to Design A Dust Collection System Clamp together ducting 45% less labor to install Easy & fast to install, just clamp together, no rivets, screws 45% less downtime or welding needed for installation Adaptable to your existing ductwork Re-useable, easy to modify and easy to move as Local dealer support your needs change Leak-tight laser welded seams, Nordfab provides: instead of lock-form or spiral duct - which badly leaks quick delivery, order tracking and lower and allows debris harbors and snag opportunities freight costs THE WORLD’S FASTEST DUCTING Step One: Layout the Machinery Of Your Shop. The first consideration is the limitation of workshop space (ceiling height, obstructions, electrical service, etc.). It is advisable to place machines requiring the largest cubic feet per minute (CFM) of airflow closest to the dust collector. The required CFM for each machine may be available in your owner’s manual. If not, measure the diameter of the dust ports on the machine and use the chart below to estimate the CFM requirements (example: if your woodworking machine has a 3”port you can infer that it requires approximately 220 CFM). If a machine has multiple dust ports, the total CFM for the machine is the sum of all of the ports. Inlet Diameter 1” 1.5” 2” 2.5” 3” 4” 5” 6” 7” 8” 9” 10” CFM 24 53 98 150 220 395 614 884 1203 1570 1990 2455 Step Two: Draw a Top-Down View Sketch (to Scale) Of Your Machines and Dust Collector.
    [Show full text]
  • Newsletter October 2015 Newsletter August 2013Ugust 2013 Welcome Years
    North Texas Woodworkers Association See us at: www.ntwa.org Volume 24, Number 10 Newsletter October 2015 Newsletter August 2013ugust 2013 Welcome years. It is random in widths, lengths A large turnout for the October and thicknesses. He will send out the meeting was welcomed by President info when it becomes available. John Loftis. Shop Questions Daniel Nilius brought in a picture of a table pedestal that has compound curves and is looking for suggestions on ways to cut it. Joe Polich suggested gluing it up much like a box then cut the first curves; tape the cutoff back in place and cut the second curves. Steve Jenkins suggested using a shaper. There was a question on how to Guests make a picture frame back with the Mike Burnett from Addison. kick stand found on many frames. Steve Yauch suggested using a base Jim Rice is new to woodworking and to hold the frame instead of the kick is interested in segmented turnings. stand. Royce Davidson from Plano heard Joe Polich cautioned everyone who about NTWA through Woodcraft. He has a DeWalt benchtop planer that if builds benches, quilt racks and kids the elevation adjustment becomes “stuff.” very difficult, don’t lube the elevation screws. Remove the top of the Announcements planner and vacuum out all the chips Vic Gutekunst’s employer is looking that are jamming the chain drive. It for someone to come in to do shop is presumed the chips are a result of maintenance on woodworking forgetting to open your blast gate equipment. It is a part time position when you operate the planner.
    [Show full text]
  • Jointer Safety and Operation
    Jointer Safety and Operation *NOTICE* Rules and guidelines listed on this page are only reminders. Persons must read lab safety manual, machine manual, and be trained by WRL Manager. Safety Rules • Safety glasses are required. Hearing protection advised. • Always run dust collection with jointer. • Keep hands 4” away from cutter head. • Never pass hands over cutter head. • Don’t place thumbs at end of piece. Use a push block. • Don’t remove guard. • Don’t adjust out-feed table. • Don’t try to remove more than 1/16” at a time. • Don’t joint stock less than 1/4” thick. • Don’t joint material shorter than 10”. • Don’t joint dirty material or material that has paint on it. • Always joint with the grain. • Be cautious of loose knots, splits and other defects in wood. These defects can cause piece to jerk and can result in injury. • Never run materials containing nails, screws or other metallic objects. • Always stand at the side of the jointer by the cutter head. • All setups other than edging and facing must be approved by supervisor. • If machine is malfunctioning stop immediately and report to supervisor. Operation • Put on your safety glasses and hearing protection. • Clean stock with brush and check for defects and metal. • Set in-feed table so that no more than 1/16” will be removed. • Don’t adjust out-feed table. • Turn on dust collection and open blast gate. • Turn on jointer. • Make sure the cutter head is at full speed before running piece through jointer. • Run stock through jointer with slight even pressure against table and fence.
    [Show full text]